Wyse Technology J400 Windows-based Terminal User Manual 883792 01A 94A5XL J400 JB QSG

Download:
Mirror Download [FCC.gov]
Document ID	328827
Application ID	gCBKrrznrGFRwN2NM2U/JA==
Document Description	Installation guide
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	49.79kB (622376 bits)
Date Submitted	2003-05-28 00:00:00
Date Available	2003-05-28 00:00:00
Creation Date	1999-03-24 14:35:53
Producing Software	Acrobat Distiller 5.0.5 (Windows)
Document Lastmod	2003-05-15 14:38:03
Document Title	883792-01A 94A5XL J400 [JB] QSG.fm
Document Creator	FrameMaker 6.0
Document Author:	mraboy

Model J400 - Winterm™ 941G XL XPE-Based Terminal
Quick-Start Guide
➊
Connect –
Caution: Improper connection, mounting, or use of this product could result in component failure and/or flash
memory corruption. Read the following caution statements before setting up and operating the terminal.
(FIGURE TO BE SUPPLIED)
PS/2-type mouse interface
Parallel port
Network connection, 10/100Base-T
Serial port
PS/2-type keyboard interface
6 Video port
7 USB port (2)
8 Speaker out
9 Line in
10 Microphone
11
12
13
14
+12V Power cable interface
Floppy drive (optional)
USB port (2)**
CD-ROM drive (optional)
Caution Statements:
Setup
•
Do not connect power until all other connections are made. Connecting or disconnecting components
or devices on the back panel when the terminal is receiving power can cause power surges and damage the
terminal. (USB ports are hot-swappable.)
•
Do not force a connector into its socket. If any undue resistance is encountered, ensure that the connector is
correctly oriented to the receptacle.
Orientation and Venting
•
Mount the terminal only as shown above or in accordance with the instructions provided with the Wyseapproved wall mount (see Note that follows). Improper orientation (such as component side down, where the
back panel’s symbols are upside down) could inhibit the dissipation of heat from the terminal and damage it.
•
Allow sufficient space around the terminal for ventilation; do not place the terminal in any enclosure that
restricts airflow around the terminal; do not place any objects on the terminal. Product environmental
specifications are available through Wyse’s Web site at http://www.wyse.com/products/winterm/products.htm.
*Supplied for U.S.A.; in other locales, check package contents or contact your Wyse reseller.
**Front USB ports not available if floppy drive option is installed.
Power Sources
•
To ensure regulatory compliance, use only the power supply included in the shipping box, or a
Wyse-approved equivalent, with the terminal. Also, the noise suppressor (ferrite bead) included in the box
with the terminal must be installed on the network cable as described following these caution statements.
Refer to the regulatory notices in the terminal’s on-line documentation at http://www.wyse.com/products/
winterm/quickstart/9000.htm.
•
To prevent accidental loss of power, brown out, and spikes which could damage the terminal, avoid
connecting it to any form of switching device (including power strips) or hard resetting the terminal by holding
down the power button.
•
When turning off the terminal, be sure to perform a complete shutdown (via the user interface or power
button); do not disconnect the power cord, shut off power at a circuit breaker, etc., to turn off the terminal.
Note: Visit http://www.wyse.com/products/accessories/mounting.htm for information about approved wall-mount
and monitor-mount accessory kits.
Note: Rubber feet are provide for horizontal orientation on hard surfaces and plastic cylinder supports are
provided for vertical orientation. Insert terminal into cylinders with the power button at the top, then press cylinder
ends firmly towards the terminal.
Note: To ensure that the product
complies with EN55022B and FCC
Class B requirements, follow these
instructions to install the ferrite bead
on your LAN cable.
➋
Turn On –
Important: By unpacking and using the terminal, you
agree to be bound by the license agreements in the users
and administrators guides. See those agreements for
specific details at http://www.wyse.com/products/winterm/
quickstart/9000.htm.
(FIGURE TO BE SUPPLIED)
➌ Configure – Setup is quick and simple...
The terminal is preset to auto-login as User (password: User). For administrative access, the terminal is preset to
accept the user name Administrator (password: Administrator). VNC is also preset to start automatically
(password: Wyse). User names are not case sensitive; passwords are case sensitive. To log in as administrator
hold down the Shift key while logging out of the user account until you get to the login screen, then enter the user
name and password for the administrator account.
Caution: It is strongly advised that the administrative password be changed immediately upon configuring the
terminal for use.
➍
Help – Need more information, upgrades/accessories, or Wyse’s automatedwarranty registration‚ process?
http://www.wyse.com/products/winterm/quickstart/9000.htm
Need more information on Wyse Rapport, the remote management software that comes with this terminal?
http://www.wyse.com/bundle
‚
Register within 90 days to get 2 years’ extended warranty at no cost.
Wyse Technology Inc.
3471 North First Street
San Jose, CA 95134-1801 U.S.A.
883792-01 Rev. A
April 2003
©2003 Wyse Technology Inc. All rights reserved.
xiii
FCC Statement
This equipment has been tested and found to comply with the limits for either Class A or
Class B digital devices (refer to "Terminal Requirements Compliance"), pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and the receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
Caution
Changes or modifications not covered in this manual must be approved in
writing by the manufacturer’s Regulatory Engineering department. Changes
or modifications made without written approval may void the user’s authority
to operate the equipment.
Terminal Requirements Compliance
FCC Compliance
The Models 9235LE, 9440XL, and 9450XE terminals meet Class B requirements.
IEC/EN Compliance
The Model 9235LE, 9440XL, and 9450XE terminals meet Class B requirements.
Canadian DOC Notices
Refer to the previous section, "Terminal Requirements Compliance," to find out to which
terminal model each of the statements below refers.
Class A
This digital apparatus does not exceed the Class A limits for radio noise emissions from
digital apparatus set out in the Radio Interference Regulations of the Canadian
Department of Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites
applicables aux appareils numériques de la classe A prescrites dans le Réglement sur le
brouillage radioélectrique édicté par le Ministère des Communications du Canada.
xiv
Class B
This digital apparatus does not exceed the Class B limits for radio noise emissions from
digital apparatus set out in the Radio Interference Regulations of the Canadian
Department of Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites
applicables aux appareils numériques de la classe B prescrites dans le Réglement sur le
brouillage radioélectrique édicté par le Ministère des Communications du Canada.
IEC/EN Notice
These products conform to the requirements of IEC950 and EN60950.
These products conform to requirements of EN55022 for Class A equipment or EN55022
for Class B equipment (refer to "Terminal Requirements Compliance").
Caution
For use with supplied power adaptor. Replace only with the same or
equivalent type as recommended by the manufacturer.
Model 9235LE Terminals
For use with External Power Supply DVE Model DSA-0301-05 or certified equivalent
model supplied by the manufacturer.
Model 9440XL Terminals
For use with External Power Supply Flytech/CARRY-I Model FT-8006A or certified
equivalent model supplied by the manufacturer.
Model 9450XE Terminal
For use with External Power Supply Li Shin Model LSE9802A1255 or certified equivalent
model supplied by the manufacturer.
Battery Information
The 9450XE terminal contains a replaceable battery.
Warning
There is a risk of explosion if the battery is replaced by an incorrect type.
Always dispose of used batteries according to the instructions accompanying
the battery.
Noise Suppressor
A noise suppressor (ferrite bead) must be installed on the network cable of your terminal.
This installation is necessary to maintain compliance with U.S. FCC B limits and European
CISPR B EN55022 Class B limits. The noise suppressor is supplied by the manufacturer
and is packed in your terminal’s shipping carton.
xv
Cable Notice
The use of shielded I/O cables is required when connecting this equipment to any and all
optional peripheral or host devices. Failure to do so may cause interference and violate
FCC and international regulations for electromagnetic interference.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Modify Date                     : 2003:05:15 14:38:03-07:00
Create Date                     : 1999:03:24 14:35:53Z
Page Count                      : 5
Creation Date                   : 1999:03:24 14:35:53Z
Mod Date                        : 2003:05:12 16:51:27-07:00
Producer                        : Acrobat Distiller 5.0.5 (Windows)
Author                          : mraboy
Metadata Date                   : 2003:05:12 16:51:27-07:00
Creator                         : mraboy
Title                           : 883792-01A 94A5XL J400 [JB] QSG.fm

EXIF Metadata provided by EXIF.tools