XAC Automation E200CP Terminal User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3419323
Application ID	kPMDfGGwUa72/UY2t6xeBA==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	120.99kB (1512329 bits)
Date Submitted	2017-06-09 00:00:00
Date Available	2017-12-07 00:00:00
Creation Date	2017-06-02 17:03:06
Producing Software	GPL Ghostscript 9.07
Document Lastmod	2017-06-02 17:03:06
Document Title	Installation Guide_xCL_E200CP_TUV Op 40C_add rear cover warning_add FCC 20cm
Document Creator	PDFCreator Version 1.7.1
Document Author:	eric_hong

CLOUD POS PAYMENT DEVICE
XCL_E200CP SERIES
INSTALLATION GUIDE
1. DEVICE OVERVIEW
Key Buttons & Interface Ports (Figure 1):
Figure 1
FRONT SIDE
Touch Panel
Smart Card Reader (SCR) slot
Smart Card Reader LED indicator
Magnetic Strip Reader (MSR) slot
Magnetic Strip Reader (MSR) LED indicator
13 keys Rubber PINPAD
Camera
Contactless LED indicator
Figure 2
LEFT SIDE
SAM Card Slot
10
Audio Jack
11
Buzzer
Figure 3
REAR SIDE
Ethernet Port
USB Host Port
Cash Draw Port
10
USB Type C Device Port
11
12V DC Power Jack
Figure 4
REAR SIDE
12
Speaker
13
Stand Mounting Holes
â–  Power Adapter spec:
Input: 100 ~240 AC
Output: 12V DC
(Use only the AC adapter approved and provided by XAC Automation Corporation for
use with this device. Use of any other AC adapter may cause a risk of fire or explosion)
Operating Temperature: 0 C to 40 C
2. USING THE MAGNETIC CARD READER
Swipe the card through the slot with magnetic stripe side facing the same direction as the
display.
Figure 5
3. USING THE IC CARD READER
Insert an IC card into the slot (Figure 6) with the chip side facing the same direction as the
touch panel
Figure 6
4. USING THE CONTACTLESS CARD READER
Tap the contactless card on top of the contactless logo
Figure 7
5. HOW TO INSERT SAM
Insert an SAM card into the slot (Figure 8) with the chip side facing
Figure 8
6. HOW TO OPEN SAM COVER
Take the screw out (1) and then pull out the SAM cover (2)
Figure 9
7. HOW TO OPEN IO COVER
Push the IO TOP cover (1) and then pull out the IO cover (2)
Figure 10
CAUTION:
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES
ACCORDING TO THE INSTRUCTIONS.
The IO & SAM covers provide for SAM card and I/O port installation Removal Warning:
When removing the screw of SAM cover and the IO,SAM covers for the purposes of SAM card and I/O port
installation, remember to put back the cover and the screw before power on the POS.
FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which case the user will be required to correct
the interference at his owns expense.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
XAC Automation Corporation
886-3-577-2738
The above information is the exclusive intellectual property of XAC Automation Corporation and shall not be
disclosed, distributed or reproduced without permission of XAC Automation Corporation.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 8
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:d790df66-49cd-11e7-0000-14e8d5bd1cf0
Producer                        : GPL Ghostscript 9.07
Keywords                        : ()
Modify Date                     : 2017:06:02 17:03:06+08:00
Create Date                     : 2017:06:02 17:03:06+08:00
Creator Tool                    : PDFCreator Version 1.7.1
Document ID                     : uuid:d790df66-49cd-11e7-0000-14e8d5bd1cf0
Format                          : application/pdf
Title                           : Installation Guide_xCL_E200CP_TUV Op 40C_add rear cover warning_add FCC 20cm
Creator                         : eric_hong
Description                     : ()
Author                          : eric_hong
Subject                         : 

EXIF Metadata provided by EXIF.tools