XYZprinting 3F11X 3D Printer User Manual QUICK GUIDE F1 1 PLUS EN V1 indd

Download:
Mirror Download [FCC.gov]
Document ID	2473989
Application ID	2kZ3WXVN9V/OHnR1GUPeGQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	115.55kB (1444437 bits)
Date Submitted	2014-12-16 00:00:00
Date Available	2014-12-16 00:00:00
Creation Date	2014-12-12 09:12:33
Producing Software	Acrobat Distiller 11.0 (Windows)
Document Lastmod	2014-12-12 09:12:33
Document Title	QUICK GUIDE_F1.1 PLUS_EN_V1.indd
Document Creator	PScript5.dll Version 5.2.2
Document Author:	TB495046

ENG
da Vinci 1.1 Plus Quick Guide
•
•
•
•
P1
Product Manual
XYZware
Print Bed Leveling and Product Specification
Support Details
02-08
09
10-11
12
V1
Product Overview
Cartridge Slot
Display Panel
Remove the
packaging supports
Extruder Module
LAN Port
Z-Axis
USB Port
Front Door
Print Bed
Power Switch
USB Flash Disk Slot
Power Connector
Remove the print bed
fixing screws and printing
module fixers
Accessory Checklist
Maintenance Tools
．USB Flash Drive
．Cartridge Locker
USB Cable
．U
．Filament Cartridge
．Side Cover Plate x2
．Glue Stick
．Power Cord
USB Content:
-Quick Guide
-Important Notice
-User Manual
-XYZware Manual
-Software
-Tutorial Video
-Print Sample
． Copper Brush
． Scraper
Cleaning Wire
． Clea
Important Safety Instruction for Use of Maintenance Tools
•The maintenance tools provided should be only handled by an adult. Please keep the tools away from children.
Incorrect handling or maintenance of the printer may cause damage to the product or personal injury.
•Be sure to maintain the printer while the print bed is cool.
•The scraper is used to remove the object from the print bed when printing has finished and the print bed is cool.
•Over time, carbon deposits or filament dust buildup in the nozzle may decrease its performance. It is advised to
clean the nozzle with the cleaning wire by activating "CLEAN NOZZLE" mode after every 25-hour of printing.
•Molten filament may be left on the tip or surface of the extruder and inside the drive gear and may decrease the
performance of the printer, or lead to calibration result of “Error”. The copper brush is used to clean and remove the
filament pieces from the extruder in these cases.
Important Safety Instruction
Do not place the printer in humid or dusty environment such as bathrooms and high traffic areas. Do not place the
printer on a rickety surface and/or inclined position. Printer may fall down/or tumble and it may cause serious injury.
Do not touch the interior of the printer while printing. As it may be hot and include moving parts. Please keep the front
door closed during printing to avoid injury.
P2
V1
Open the box
Note: All packaging materials should be removed before powering up the printer.
1 Open the box and remove
the accessories and the
cushion.
2 Take out the printer by
the grip holds.
Tape x2
4 Open the top cover, and
remove the cushions by
the extruder
7 Remove the cushions by
the print bed.
5 Remove the cardboard.
8 Remove the cardboard.
10 Insert the USB flash drive to install XYZware
for printing.
P3
all tapes.
Cable tie
x1
Packing support x2
3 Remove plastic bag and
6 Remove the tape on the
print bed.
9 Remove the bottom
screw and plastic piece
under print bed.
11 Use the USB cable to connect the printer
to PC. Connect the power cord to the
printer then turn on the power switch.
V1
Initial Settings
After powering on the printer for the first time, complete the simple setup as instructed on the screen.
Then select language and press
Home Menu
to proceed.
Filament
Network Status
Load, unload filament and view the
information about the filament.
Display online status of Wi-Fi
or Ethernet network.
Browse the file for
printing
Print from the cloud
gallery
Print from USB flash drive*,
"My Gallery" and sample
folder.
Browse the content of
XYZprinting gallery and
select for printing.
Settings
View the printer
status and system
settings.
Function
Guidelines
Home menu
basic operation
introduction.
*Please export .stl files into .3w format via XYZware before printing.
P4
V1
Load Filament
First install the cartridge to the cartridge slot…
1 Remove the filament
stopper and tape.
2 Install the new filament
cartridge into the empty slot.
3 Place and push to click the cartridge.
4 Select "Filament" > "Cartridge " > "Load".
Guide
Hole
Cartridge
Top
cover
5 Insert filament into the guide hole until the printer starts to load filament.
(When the loading begins, you will hear the sound of motor and can see
the filament is pulled into the printer.)
Note : Before pushing the filament into the guide hole, please cut the tip of the filament off at a 45°
angle with a cutting pliers, filament loading will be easier.
6 If filament doesn't come out from the nozzle,please press "Retry" or "Cancel". When filament is
dripping off the nozzle,tap
P5
to finish.
V1
Sample Print
1 Select "Print" > "Sample " on the screen.
2 Select a sample to print, and tap
to print.
3 Apply glue stick gently and evenly to the print bed base on the
size of the printing object previewed on screen, and press
on the screen. You may click
to print.
for "Printer info" during printing.
5 Remove the printed object when the
print bed has descended.
P6
4 Printing process is shown
6 Cover a damp cloth on the cold print
bed for 2-3 minutes, and wipe the
glue off gently (Scrape off the glue if
necessary).
V1
Cloud Gallery
1 Once the printer is connected
to the Internet, select "Gallery"
to go to XYZprinting cloud
gallery.
2 Browse the Gallery and switch among different categories; tap on
the desired model for a zoomed-in preview.
3 Preview the image and
information of the selected
model, and tap
to
proceed.
4 Press
to download, and wait for the download to complete.
Caution:
Before printing any model from any media, always remember to apply glue to the printing area on the
printing bed. To clean the printing bed after printing is complete, please refer to the Sample Printing
section.
P7
V1
Unload filament
Please always complete the procedure for " Unload Filament " before changing a new cartridge.
1 Select "Filament" > "Cartridge" > "Unload" on the screen
2 F i l a m e n t i s u n l oa d e d f ro m
extruder automatically. Gently
pull filament out from the guide
hole when prompted.
3 When filament is pulled out,
press
4 Remove cartridge locker
and the catridge.
Filament troubleshooting
When the filament is loaded automatically or is stuck in the extruder module, please first unload filament by
following the steps above. And then press on the black rubber fixers on either ends of the filament tube. You may
also follow the instructions on the screen for troubleshooting.
Status
1 If the filament is stuck in the
extruder module, press the release
arm on the side of the extruder
module to extract the stuck
filament.
P8
2 If the filament is stuck at the
entrance of the guide tube,
please press the release arm by
the entrance to extract the stuck
filament.
3 After removing the filament, plug
the filament tube directly back to
its original position to complete
the re-installation.
V1
XYZware
To transmit print object(s) via USB flash drive or PC to your da Vinci printer, please prepare the file with
XYZware. When your PC is connected to the printer, you can send the object(s) to printer directly.
XYZware virtualizes the printing platform on the screen. You may move, rotate and resize the object(s)
in the software, and send the file for printing via USB flash drive or PC.
Save .stl file
Export to .3w format
Import .stl,.3w file
Zoom in/out
Setup printing preference, and
send for printing
Setup XYZware language
and preview colors
Check and update
software and firmware
version, link to
XYZprinting website
Switch views
Move object
Rotate object
Resize object
View info
about object
Remove object
from the visual
plate
Check the
temperature of
extruder/print
bed, cartridge
statistics and
printing progress
XYZware is compatible with Windows XP, Windows 7+ and Mac OS 10.7+, please install the software
via the USB flash drive in accessory tray or download the latest XYZware for your OS from XYZprinting
website:
http://support.xyzprinting.com/Support/downloads
For the latest software updates and further information. Please go to:
http://support.xyzprinting.com/Support/manuals
* Note :
Some instruction and video tutorials might require online registration to obtain authorization.
Please sign up for XYZprinting membership before downlloading XYZware.
P9
V1
This print bed has been calibrated by our professional technician
before shipment. Do not adjust the platform yourself unless
necessary, or contact the customer service center.
Print Bed Calibration
1.Check for firmware update
In XYZware, select “About” > “Firmware Update”.
2.Activate Calibration
Select "Setting">"Printer Settings">
"Maintenance" >"Calibrate Print Bed" and
press
to perform calibration.
The printer starts automatic measurement.
Wait for 2~3 minutes and verify the data shown.
Note: During the measurement process, the print bed
and extruder module will be heated.
Care should be taken during operation!
3.Wait for detecting
What does “detecting” do:
The printer measures the distance between the detecting pin and 3 measurement points at the corners of the
print bed to check if the platform is leveled. When the height of the 3 points are no more than ±0.2 from each
other, the print bed is leveled.
4.Check the detecting result on the display
１."Calibration Completed”
- ready to print
The print bed is leveled;
adjustment to the print bed is
not required.
Skip step 5 & 6, and press
to
２."Calibration Not Completed”
and "Error" is shown - cleaning &
leveling is required
The detecting point is too
high/low for detection or the
pin/measurement point is
covered by molten plastic.
Press
and proceed step 5 and 6.
3."Calibration Not Completed”
- leveling is required
Unleveled print bed may
affect printout quality. Please
level the printbed based on
the value of P1, P2 and P3.
Press
and proceed step 6.
finish.
P 10
V1
5.Clean the detecting pin
Select “Clean Nozzle” function, and brush the molten filament and dust from the detecting pin while the
extruder is heated up.
Clean the detecting pin with the copper brush
Clean the 3 measurement points
Activate " Setting" > "Printer Settings">
"Maintenance">"Clean Nozzle".
6.Level the print bed
1.The value indicates the height of point P1 P2 P3 ; greater value indicates the higher the detected point is.
2. Turn the 3 turning screws at location "a", "b", "c" under the print bed to level the platform.
P1
P3
P2
How to adjust :
• Turn clockwise to raise, turn counterclockwise to lower.
• Adjust screw a and b may offset the diagonal. (e.g. Left turn screw b will lead to the descendant of point 2.)
• Tuning the screw for a full circle will change the value by 0.5. A single push to the screw will change the
value by 0.2 to 0.25.
Thumb of rules:
• Adjust the values to the 2.3-2.6 range.
• 3 values should be no more than ±0.2 from each other.
When finishing the adjustment, repeat the calibration from step 2 until it shows "Calibration Completed".
Specifications
Model Name
da Vinci 1.1 Plus 3D Printer
Nozzle Diameter 0.4mm
Print Technology
Fused Filament Fabrication(FFF)
AC Input
Print Head
Single Head
Build Volume
20 x 20 x 20 cm
100 - 127V~4.0A 50/60Hz
200 - 240V~2.0A 50/60Hz
Connectivity
(W x D x H)
USB 2.0 / WiFi
LAN / USB Flash Drive
Layer
Standard 200 microns
Display
5" TFT LCD
Resolution
Speed 300 microns
Control Method
Touch Panel
Setting
Ultra fast 400 microns
Indicator
Speaker
Custom 100-400 microns
Weight
27 Kg
Filament Diameter 1.75mm
P 11
V1
Support Details
The troubleshooting instruction may guide you to fix the problem. If any error persists, please contact
customer service center for support.
Customer Support Center:http://support.xyzprinting.com
Technical Support (US):supportus@xyzprinting.com
Technical Support (EU):supporteu@xyzprinting.com
Other Region:support@xyzprinting.com
Service
Code
Symptom
Action
Service
Code
Symptom
Action
0 0 0 3 problem
Reboot the printer.
0 0 2 9 Cartridge 1 empty
Replace cartridge 1 before
printing.
0 0 0 7 Cartridge 1 chip error
0030
X-axis movement
abnormalities
Y-axis movement
0031
abnormalities
Check motor/sensor connections.
Check sensor position.
Check motor/sensor connections.
Check sensor position.
0 0 1 4 problem
Reinstall the cartridge 1 or
change a new cartridge.
Reinstall the cartridge 1 or
change a new cartridge.
Check connections, reboot the
printer.
Check connections, reboot the
printer.
Check connections, reboot the
printer.
Check connections, reboot the
printer.
0 0 2 8 Cartridge 1 not installed
Install/reinstall cartridge 1.
0 2 0 1 between PC and printer the cable between printer and PC.
Print bed heating
0 0 0 8 Cartridge 1 chip error
Print bed heating
0 0 1 0 problem
Extruder 1 heating
0 0 1 1 problem
Print bed heating
0 0 1 3 problem
Extruder 1 heating
Check motor/sensor connections.
Check sensor position.
Check if SD card is inserted
0 0 4 0 Internal storage error correctly.
0032
Z-axis movement
abnormalities
0 0 5 0 Memory error
Internal
0 0 6 0 communication error
Connection error
Reboot the printer.
Reboot the printer.
Reconnect PC to printer, or hotplug
Action
Error message
The printer is handling other task
Try again after all tasks are completed. Also check the information shown on printer display.
Unable to update printer firmware
Check Internet connectivity/Update firmware again later.
Filament 1 jammed
Unload and reload cartridge 1 and clean the nozzle.
Filament 1 loading problem
Unload and reload cartridge 1.
Filament 1 installation problem
Reinstall the cartridge 1 or change a new cartridge.
Top cover open
Close the top cover.
Filament 1 level low: 30m left
Replace cartridge 1 when necessary.
Filament 1 level low: 5m left
Replace cartridge 1 immediately.
Federal Communications Commission (FCC) Statement
You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s
authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
XYZprinting is not responsible for any radio or television interference caused by using other than recommended cables and connectors
or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user's authority
to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of
the FCC RF Rules. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used
for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located
or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation
instructions and consider removing the no-collocation statement.
P 12
V1

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : TB495046
Create Date                     : 2014:12:12 09:12:33+08:00
Modify Date                     : 2014:12:12 09:12:33+08:00
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Format                          : application/pdf
Creator                         : TB495046
Title                           : QUICK GUIDE_F1.1 PLUS_EN_V1.indd
Creator Tool                    : PScript5.dll Version 5.2.2
Producer                        : Acrobat Distiller 11.0 (Windows)
Document ID                     : uuid:f679dc15-2061-453f-8f1e-34039067587f
Instance ID                     : uuid:da32ee74-e1d7-40cc-bd5f-9c4e9f121a25
Page Count                      : 12

EXIF Metadata provided by EXIF.tools