XceedID XF2100C Multi-Tech Credential Reader User Manual

XceedID Corporation Multi-Tech Credential Reader Users Manual

Users Manual

DescriptionThe Multi-technology Readers feature a rugged design and can be installed almost anywhere. Durable, weatherproof, UV-resistant materials, along with advanced electronics and circuitry, protect readers against inclement weather and exposure to sunlight. Mounting the Reader1. Find a suitable mounting position on the door frame or wall. Note: For out of doors or wet locations, it is recommended that the gasket provided be installed on the base as shown in Figure 2. 2. Drill two mounting holes a minimum of 3.25” (82.6 cm) apart on the mounting surface of the door frame or wall. Refer to Figure 3. 3. Drill one .625” (1.587 cm) diameter hole in wall for the pigtail wire connection.4. Follow the cable connection chart. Connect power at the panel when installation is complete.5. Mount the base plate to the wall using the supplied screws.6. Install gasket if required, see Figure 2.7. Install top cover straight on to the reader base. Do not force the cover on. The four cover guides should ensure the connector seats correctly. 8. Verify the connection is secure and install the security screws at the top and bottom of the reader.9. Place a screw head cover over each of the screws. The screw head cover should be flush with the reader once in place.5.850 [148.6]1.160[29.5]1.750[44.5]front view side viewXceedID Corporation3899 Hancock ExpresswaySecurity, CO 80911Tel: 303-273-9930Fax: 303-273-9937www.xceedid.comMulti-technology ReadersInstallation Guide Figure 1. Multi-technology Readers Figure 2. Gasket Installation Figure 3. Figure 4. Aligning base plate and top cover
SpecificationsThe voltage specification for this reader is 8-16 VDC. Higher voltage with the specifications provides better performance and cable run distances.The recommended cable gauge is 18-gauge to 22-gauge. Check with the cable supplier to determine the best choice for the application and installation distance.FCC complianceThe FCC requires the following statement: This reader usesradio frequency energy and has been tested, and complieswith the limits of FCC testing. Changes, modification,or disregard of proper installation and instructions notexpressly approved by XceedID, and is strictly prohibited bythe FCC and could void the user’s authority to operate theequipment.a. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. b. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.Colors Black (standard), charcoalPower supply Linear DCVoltage range 8 - 16 VDCMaximum and Average Current rangeXF2110C: 173 mA (max), 155mA (aver)XF2100C: 157 mA (max), 141 mA (aver)XF1100C: 132 mA(max), 116 mA (aver)Temperature range -31 F to 149 F-35 C to 65 CCard read distance Distance can vary depending on reader, installation conditions and credential type.Cable distance to panel 200 ft. max (22 gauge)300 ft. max. (20 gauge)500 ft. max. (18 gauge)Wiegand output Up to 200 bits depending on configuration and card technologyTamper output Open CollectorRegulatory approvals and standardsUL, CE, and FCC (part 15)ISO Standards ISO 14443AISO 15693Ordering InformationProduct DescriptionXF-1100-B (Standard Black)Mullion mount; Wiegand outputXF-2100-B (Standard Black)1-Gang US mount; Wiegand outputXF-2110-B (Standard Black)1-Gang US mount; Keypad; Wiegand outputXF-1100-C (Charcoal) Mullion mount; Wiegand outputXF-2100-C (Charcoal) 1-Gang US mount; Wiegand outputXF-2110-C (Charcoal) 1-Gang US mount; Keypad; Wiegand outputTesting the Reader1. Power up the reader. A red LED will light followed by a beeper tone, which indicates the reader is ready.2. Present a proper card, which has been programmed to operate the reader. * A green LED indicates a registered badge read. * A red LED indicates idle (ready to read) state in the Wiegand mode. Removing the Cover1. Remove the plugs and security screws.2. Slide cover off perpendicular to base.Trouble Shooting1. If reader does not behave normally upon installation, verify that cover and base are connected properly: The reader is shipped unassembled. To assemble, pull cover away from base and rotate until the connector port on the base is aligned with the connector port on the cover. Snap shut.2. Only connect wires necessary for use. Cut and/or isolate unused wires. Connecting unnecessary wires may lead to unexpected reader behavior. 3. If multiple reader units are installed in close proximity or back to back, RF interference may result in reduced read range performance. 4. A recurrent triple beep audio sequence may indicate that the cover is not seated properly. Remove cover and check for bent or broken pins in the connector.Copyright © 2007-2011, XceedID. All rights reserved. Revised 2/1/2011.Connecting the Cable1. The readers are supplied with a 12-conductor cable pigtail. Ensure the reader wiring is disconnected at the host panel until all connections are made at the reader. Use the cable connection chart below:2. Use a DC Power source between 8-16 volts.3. Verify the reader is properly grounded by attaching the ground wire to an earth ground connection at the power supply or panel end of the cable.Yellow BeeperBlue HoldPurple FutureGreen Wiegand Data 0 or RS485AWhite Wiegand Data 1 or RS485AOrange Green LEDBrown Red LEDRed Power + DC (6-16 VDC)Black GroundPink Not UsedGray Not UsedDrain Shield Ground

Navigation menu