Xirgo Technologies XT1000 Wireless Zigbee Sensor User Manual user guide

Xirgo Technologies Inc. Wireless Zigbee Sensor user guide

user guide

1XT-1010 User GuideModel: XT-1010FCC ID: GKM-XT1000IC: 10281A-XT1000Version 1.1
2Table of ContentsDocument Change History .......................................................................................... 31. Introduction ........................................................................................................... 41.1 Feature Matrix................................................................................................................................................................................. 42. Hardware Description ............................................................................................. 52.1 Hardware Specifications ............................................................................................................................................................. 62.2 Cable Harness Description......................................................................................................................................................... 62.3 LED Description.............................................................................................................................................................................. 73. Device Mounting Options: ...................................................................................... 73.1 Screw Mounting.............................................................................................................................................................................. 73.2 Magnetic Mounting........................................................................................................................................................................ 83.3 VHB Tape Mounting...................................................................................................................................................................... 84. Quick Start Guide.................................................................................................... 94.1 Device Installation......................................................................................................................................................................... 94.2 Pairing the XT1010Z and the XT4860G5 ...........................................................................................................................104.3 Unpairing Devices........................................................................................................................................................................10
3Document Change HistoryRevisionDateAuthorChanges1.08/28/2014Johnny ChenDocument Creation1.19/2/2014Johnny ChenRevision Based on Nader’s Feedback
41. IntroductionThe XT-1010 is a wireless ZigBee sensor that pairs with the XT-4860G5 generally known as the BaseUnit to provide inclination data based on a 3-axis digital accelerometer readout with an accuracy of±1 degree. Additional general purpose digital IO sensors can also be queried and transmitted to theXT-4860G5. The XT-1010 leverages a high efficiency solar energy harvesting platform to support longterm, remote deployments without the burden of frequent battery replacement. This installationguide describes the physical hardware, associated parts, mounting options, and a quick start-upprocedure.1.1 Feature MatrixFeature DescriptionXT-1010High Efficiency Solar Panel6600mAh Rechargeable Li-Ion BatteryDiagnostic LEDsOptional Digital IO Sensors and 1-Wire Serial BusZigBee pairing with XT-4860G5Inclinometer Data based on 3-axis Dig Accel. with 1 deg. accuracyOver-the-air FW upgrade via XT-4860G5
52. Hardware DescriptionBelow is a depiction of key interfaces of the XT-1010:An optional Cable Harness that interfaces with the unit is shown below. The Cable providesexternal power, when available, as well as interface to the IO HW optionsSolar PanelLED IndicatorsDevice LabelZigBee PairingButton8-Pin BayonetConnector
62.1 Hardware SpecificationsZigBee SpecificationTechnologyZigBee IEEE 802.15.4 DSSS modemFrequency Band2405-2483.5MHzAntenna gain0.5 dBi (peak again), -0.5 dBi (Average gain)Transmit power12dBm/MHzData Rate250 kbpsPower RequirementsD.C. Power (if Avail.)8-24V, 12 V nominalBatteryInternal 6600mAh rechargeable Li-IonPhysical ConnectionInterface Connector8-pin Bayonet typeProgrammingSerial (UART Logic Level)MechanicalCase MaterialABS plastic with weather-proofing for outdoor useDimension7.6” X 4.9” X 1.4”Weight18 oz.Operating Temperature-30°C to +70°CProtection RatingIP672.2 Cable Harness DescriptionPin #WireColorPin NameFunctional DescriptionPort Characteristic1WhiteIN1Ignition Sense8v to 24v, Internally pulled low2YellowIN2Input port2.4 to 24V, < 0.2 VNote: Internally pulled high3BlackGroundGround4GreenOutOutput Port (Defaulted open circuit)5BlueUART-RxExternal battery negative terminal3.3V Logic InterfaceCom Port Settings:Baud rate: 115200 bps; Flow control:None; 8N16BrownUART-Tx3.3V Logic InterfaceCom Port Settings:Baud rate: 115200 bps; Flow control:None;8N17RedVBATTMain battery voltage, DC8-24 V, 12V Nom.8OrangeADCAnalog Input8-24 V
72.3 LED Description3. Device Mounting Options:3.1 Screw MountingThe XT-1010 can be mounted via 4 mounting screw, 2 per side as depicted below.LEDDescriptionStatusGPS (Green)Pairing SuccessfulSolid for 30 Seconds then OFFStand-by for PairingBlinking Steadily
83.2 Magnetic MountingThe XT-1010 can also be provided with 4 pre-installed (or kitted separately) magnets as depictedbelow.3.3 VHB Tape MountingFor semi-permanent mounting option, the device can be mounted with 3M VHB tape as shownbelow.
94. Quick Start Guide4.1 Device InstallationThe XT1010 (Sensor unit) pairs with the XT-4860G5 (Base unit) and provides inclinometer databased on the on-board 3-axis digital accelerometer output which in turn is transmitted to enduser Server over the cellular network. The proper installation of the unit is critical to acquiringaccurate inclinometer data. An application note entitled “Installing and Pairing the XT-4860 andXT-1010 for Wireless Inclinometer Functionality” contains detailed instructions for installing andpairing the two devices. This quick start guide will give you basic steps for installation andpairing of the two devices. Refer to the application note for any additional detail and instructions.When installing the device, make sure the Base unit (XT-4860G5) faces the Sensor unit (XT-1010)Each Unit has a label near the 8-pin Connector to show the direction of device installation. TheBase and the Sensor must be on the same plane and facing each other for optimal performance.The picture below illustrates the ideal orientation of the two devicesAs an example, below depicts possible mounting positions of the two Units for a man-liftapplication.FACE BASE UNITFACE SENSOR
104.2 Pairing the XT1010Z and the XT4860G5With both Base and Sensor units properly oriented, the pairing process of the two devices canbegin. Note that only one Sensor unit can be paired with one Base unit. During the pairing process,the devices are calibrated and normalized relative to each other. Once the calibration is complete,the Devices must not be moved or repositioned.To begin the pairing process, press the black button located near the circular connector on theside of the Base unit for 5 seconds. You should see the amber LED light (marked with “Z”) flashing4 times per second. This LED pattern signifies that the Base unit is searching for the Sensor unitthat it is meant to pair with. There is a 60-second window for the pairing process to complete. Ifthe pairing process was not successful within 60 seconds, then the unit will return to itsconfigured normal state and the process needs to be repeated if pairing is still needed. At anytime during pairing, the process can be stopped or reset by pressing and holding the button oneither device for 15 seconds, then releasing, or by simply waiting for a timeout.During the Base unit 60-second pairing time, press and hold the pairing button on the Sensor unitfor 5 seconds. The green LED (marked with a “C”) will flash 4 times per second as well. A typicalpairing process takes about 3 to 5 seconds after pressing the pairing buttons of both Units. Aftersuccessful pairing, the Base unit’s orange LED will turn off and the Sensor unit’s green LED willturn solid for 30 seconds, then it will turn off. After the pairing process, the Sensor unit willautomatically send inclinometer data to the base unit at a rate of 1 sample per 5 seconds.4.3 Un-pairing DevicesTo un-pair a set of paired XT-4860 and XT-1010 devices, press and hold the button on the XT-4860 device for 15 seconds, then release. That device will attempt to notify its XT-1010 pair ofthe pairing reset. There is no LED feedback for a pairing reset. The pairing reset can be performedindividually on an XT-4860 or XT-1010 device if the paired device is no longer present.Pairing Button
11FCC/IC:REGULATORY COMPLIANCE INFORMATIONThis equipment with FCC-ID: GKM-XT1000 and IC: 10281A-XT-1000, Model: XT-1010is subject to the Federal Communications Commission (FCC) and Industry Canada (IC) rules.NOTICE:Changes or modifications not expressly approved by the party responsible for compliance could void the user'sauthority to operate the equipment.This device complies with Part 15 of the FCC Rules and with license exempt Radio Standard Specifications ofIndustry Canada.Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and(2) this device must accept any interference received, including interference that may cause undesiredoperation.Les changements ou modifications non expressément approuvés par la partie responsable de la conformitépourraient annuler l'autorité de l'utilisateur à utiliser l'équipement.Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts delicence. L'exploitation est autorisée aux deux conditions suivantes :(1) l'appareil ne doit pas produire de brouillage, et(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage estsusceptible d'en compromettre le onctionnemenRadio frequency radiation exposure Information:This equipment complies with FCC radiation exposure limits set forth for an uncontrolledenvironment. This equipment should be installed and operated with minimum distance of 20 cmbetween the radiator and your body. This transmitter must not be co-located or operating inconjunction with any other antenna or transmitter.

Navigation menu