Xmark IPSR 434MHz International Patient Security Receiver User Manual

Xmark Corporation 434MHz International Patient Security Receiver Users Manual

Users Manual

Service LightThe red service light is located on the lower side of the Receiver, next  to  the  service  pin,  and  is  used  for  troubleshooting.Red Service LED state DescriptionO Normal operation.Flashing every 0.5 sec. Uncongured Receiver. Run Auto Congure using the PS System Man-ager.On Failure. Check power supply to the device. Download Neuron rmware to the Receiver using the PS System Manager.Momentarily on Service pin pressed.WarrantyStanley Healthcare Solutions’ products are warranted against defects in materials and workmanship and shall perform in accordance with published specifications for a period of one year. Stanley Healthcare Solutions’ warranty is limited solely to the repair or replacement of the defective part or product. Stanley  Healthcare Solutions  reserves  the  right  to  change product specifications without notice.Limitation of LiabilityThis Product has been designed for use to assist in the preven-tion of patient abduction and/or wandering incidents.The range, accuracy, function and performance of this Prod-uct may vary from the published specifications due to many factors, including, but not limited to, site impairments from structural effects, metal objects in the vicinity, placement of the receiver and transmitter, interference from other electrical devices,  atmospheric  effects,  installation,  and  maintenance. There may be other factors, which also affect performance of this Product. XMARK Corporation (“XMARK”) does not guarantee that this Product will detect 100% of patient abductions and/or wandering incidents, nor does XMARK guarantee that this Product will not return false reports of calls for patient abduc-tions and/or wandering incidents.Monthly testing and maintenance of this Product, as described in the Product documentation, is essential to verify the system is operating correctly and to ensure that the probability of detect-ing an alarm and/or locating the transmitter are maximized. The failure to undertake regular testing and maintenance will increase the risk of system failure and failure to detect patient abductions and/or wandering incidents. The failure to under-take regular testing and maintenance will increase the risk of false reports of patient abductions and/or wandering incidents.XMARK hereby disclaims all warranties, express or implied, arising out of or in connection with any of its Products of the use or performance thereof, including but not limited to, where allowable by law,  all other implied warranties or conditions of merchantability, fitness for a particular purpose, and those arising by statute or otherwise in law or from a course of dealing or usage of trade.XMARK’s liability to you or anyone claiming through or on behalf of you with respect to any claim or loss arising out of the use or misuse of XMARK’s Product, defective prod-ucts or materials, improper installation or maintenance of XMARK’s Product or products or the system in which they are incorporated, or alleged to have resulted from an act or omission of  XMARK or any person, negligent or otherwise, shall be limited to the following, at XMARK’s sole option:1)  the repair or replacement of defective Product or materials supplied by XMARK during the warranty period as set out in the Product documentation; or, at the option of  XMARK, 2)  a refund of the purchase price of the Product supplied by XMARK.In no event shall XMARK be liable for general, specific, indirect, consequential, incidental, exemplary or punitive damages or any losses or expenses suffered by you or anyone else, whether or not XMARK, or its employees, officers, agents, resellers or installers has been informed of the risk of such loss or expense and whether or not such losses or expenses were foreseeable.StatementsUnited States—Federal Communication Commission (FCC)This device complies with Part 15 of the FCC Rules. Opera-tion is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the  FCC Rules. These limits are designed to  provide reasonable protection against harmful interference when the equipment  is  operated  in  a  commercial environment. This equipment generates,  uses, and  can  radiate radio  frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Warning:  Changes  or  modifications  not  expressly  approved  by XMARK could void the user’s authority to operate the equipment.Canada—Industry CanadaThe term “IC:” before the certification/registration number only  signifies  that  Industry  Canada  technical  specifications were met.European Union—CE DeclarationXMARK  hereby declares  that  this  radio  frequency receiver is  in  compliance  with  the  essential  requirements and  other relevant provisions of the following EU directives: (1) RTTE Directive 1999/5/EC, (2) CE mark Directive 2004/108/CE, and (3) LVD 2006/95/EC.Patient Security Receiver Installation Guide
Important!Have you: •  Pulled network and power cable?•  Resolved power supply requirements?•  Selected the location for the PS Receiver?Materials Required•  International Patient Security Receiver (p/n 816A1001)•  Facility fl oor plan indicating Receiver position and net-work wiring path•  105 Ω network terminator (p/n 805A2401)  - if this is the last device on the network segmentSpeci cationsRecommended Receiver Antenna OrientationFor best coverage, ensure that the antennas are at least 3 ft. (91 cm) from metal objects, such as fram-ing or air ducts. Do not encase, wrap, or otherwise cover the antennas.One antenna must be pointing downward with the second antenna aimed horizontally into a clear area, free of metal objects. The two antennas must be at right angles to one another.Use the illustrations below as a guideline for antenna orientation.Certi ed to the ISO 9001 Quality StandardPart Number: 816A1001Model International Patient Security ReceiverPart Number 816A1001Frequency 434.17  MHzSupply Voltage 12-30 VDCCurrent Draw 150 mA max. @ 12 V, 80 mA max. @ 24VDetectionRadius 35 ft. (11 m) for typical Receiver setup50 ft (15 m) Receiver in open spaceCommunications LonWorks two wireEthernet port - currently non-functional. Temperature Operating: 32°F to 120°F (0°C to 49°C)Storage: -22° to 158° F (-30° to 70°C)Humidity 0-85% RH @ 70°F (21°C), non-con-densingDimensions Approximately 6.1 x 4.9 x 1.7 in. (155 x 125 x 45 mm)Weight Approximately 8.5 oz. (240 g)Read these  instructions  thoroughly before installing  the  PS  Receiver.  Faulty  installation can lead to system failure.Patient Security Receiver Installation Guide309 Legget Drive    Ottawa, ON  K2K 3A3    Canada Telephone: 1.866.559.6275   International: +1 (613) 592.6997   Facsimile:  (613) 592.4296Web site: www.stanleyhealthcare.com©  2010 XMARK Corporation. All Rights Reserved.Printed in Canada. October 2010. 981-806009-000 Rev 03.
4  Install the Mounting Plate. Referring to the facility floor plan, decide the position of the Receiver. Do not place near metal objects and structural frames. Ensure that the service light will be visible and that space is allowed for the antennas.  Install the mounting plate using one of the following methods. A  Fasten to a suspended ceiling guy wire, using:•  1 multi-function Caddy clip •  2 machine screws•  2 hex nuts•  2 lock washers, OR B  Install directly to a ceiling or a wall using:•  2 wood screws•  2 hollow wall anchors, ORInstall to a receptacle box, using:•  2 machine screws5  Install the Receiver to the Mounting Plate.Plug the  wired  terminal  block  into  the  Receiver and install the Receiver onto the Mounting Plate, using the screws removed in Step 2. DO NOT place excess net-work and power supply wires inside the Receiver case.6  Attach the two clips to lock the antennas in place. Final StepsOnce all devices are installed, power up  the  Receiver and other  devices.  Using the  PS System Manager, run  Auto Configure to  install  the  new devices, and then configure them for operation.The coverage area of the Receiver must also be checked.  Status LightThe green status light is located on the front of the Receiver, and indicates the current status of the Receiver.Green Status LED stateDescriptionOff No tags within range or no power.Flashing coincident with tag transmissionsThe Receiver is receiving tag transmissions. Flashing steady for two seconds, off for one second repeatedlyWink command currently operating.NOTE: Intermittent flashes between the steady two second flash indicates the presence of tags within the area.On Failure. Check power connections or download rmware to the Receiver using the PS System Manager.Installation Considerations•  Position the Receiver beneath ceiling obstructions—When  installing  above drop ceilings,  mount  the Receiver below metal duct work and pipes•  If ceiling tiles are foil-backed, mount Receiver below. •  Route cables up and away from the Receiver—When the cable is not in conduit, route it directly away from the Receiver for at least 1 foot (30 cm). •  Install the Receiver temporarily until testing is com-plete—Fastenings should be secure enough that the Receiver can be permanently mounted without dis-turbing its orientation.•  Point the horizontal antenna into a clear area, away from metal  objects—One  antenna always  points downwards, with the second antenna (horizontal) at a 90 degree angle (can be adjusted to suit site condi-tions). Make sure the horizontal antenna is not run-ning parallel to cabling in the ceiling. •  Observe  temperature  and  humidity  restrictions—Refer to the Specifications table. •  Leave slack in the cable—Leave at least 10 ft. (3 m) of slack in the communication and power cables to allow for adjustments in the location of the Receiver. •  No user adjustments to internal circuitry—Tampering may cause component or system failure, or both, and will void the warranty.Installing the Patient Security ReceiverThe steps below correspond to the numbers in Figure 1.1  Record the LonWorks Neuron ID number.Locate and record the LonWorks Neuron ID number onto the facility floor plan indicating the Receiver’s position and network wiring path. Affix one of the supplied Neuron ID labels on the floor plan and affix the other on the Receiver in a visible location.2  Remove the  Mounting Plate  from the  Receiver by sliding it  off. If the Receiver is  to  be installed to  a receptacle box, pass the  network and power supply wires through the hole in the Mounting Plate. 3  Wire the terminal block.Connect the LonWorks Network IN, Network OUT, and Power Supply to the terminals. If the Receiver is at the end of the network segment, then terminate the network segment with a 105 Ω terminator.  •  Ensure that the power supply and net-work are turned off to prevent electrical shock or damage to equipment. •  Touch your hand to ground to discharge any electrostatic charge before handling the Receiver.Do not supply power to the Receiver or any other network device until all connections are complete.Patient Security Receiver Installation Guide
Figure 1: Physical Connections for the ReceiverPlace one Neuron ID label onthe Receiver in a visible location. For ceiling mounts, fasten to a suspended ceilingguy wire using a caddy clip.4B6POS+NEG-POWERNETWORKINNETWORKOUTIf the Receiver is at the end of thenetwork segment,use a terminator as shown below.!Labelled "OUT"DO NOT CONNECTPOS+NEG-POWERNETWORKIN!ITEM A105    terminator(at each end  of network)Labelled "OUT"DO NOT CONNECTIf the Receiver is not at the end of the network segment,connect the wires as shown below.(non-polarized)(non-polarized)(non-polarized)Patient Security Receiver Installation Guide

Navigation menu