Yaesu Musen 20485X40 Amateur Radio with scanning receiver User Manual Operating Manual

Download:
Mirror Download [FCC.gov]
Document ID	2578124
Application ID	A6Sfh4y1VH+s3GE1yfxBjA==
Document Description	User Manual Part 2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	260.93kB (3261670 bits)
Date Submitted	2015-04-08 00:00:00
Date Available	2015-07-07 00:00:00
Creation Date	2015-04-08 11:19:34
Producing Software	Adobe PDF Library 10.0.1
Document Lastmod	2015-04-08 11:19:47
Document Title	Operating Manual
Document Creator	Adobe InDesign CS6 (Windows)
Document Author:	YAESU MUSEN CO., LTD.

Application for FCC / IC
FCC ID: K6620485X40
IC: 511B-20485X40
Connecting the Radio
Connecting the controller to the main body
Caution
Make sure the power supply is switched OFF before connecting the cable between the controller and
the main body.
1 Plug the connector of the controller cable into the
[CONTROL] jack at the front of the main body
until a click sound is heard
Main
body
Controller
cable
2 Plug the other connector of the controller cable
into the [CONTROL] jack at the back of the
controller until a click sound is heard
Before Using
Controller
Controller cable
Connecting the microphone
1 Plug the microphone connector into the [MIC]
ABC
Connecting the antenna
1 Attach the antenna co-axial cable to the [ANT]
terminal at the back of the main body and tighten
the connector
Microphone
PQRS
TUV
WXYZ
P1
JKL
MNO
LAMP
Tips • To remove the microphone, pull the connector out
while pressing the latch.
• Using the optional microphone extension kit “MEK2”, a microphone with a 8-pin connector can be
used. A microphone extension cable (about 3 m
long) is also included in MEK-2. Use it to install the
microphone in locations which cannot be reached
by the attached microphone cable.
DEF
GHI
LOCK
MIC
jack at the front of the main body until a click
sound is heard
P3
P4
P2
DTMF MICROPHONE
MH-48
Connector
Main
body
本体
（後面）
(rear side)
同軸ケーブル端子
Co-axial
cable connector
17
Application for FCC / IC
FCC ID: K6620485X40
IC: 511B-20485X40
Connecting the Radio
Connecting the external power supply equipment
When using this radio as a fixed station, use an external 12 V DC power source.
Cautions
zz Use an external power source capable of supplying DC 13.8 V, a current capacity of 20 A or more
(FTM-100DR).
zz Make sure to switch OFF the power of the external power source before connecting.
1 Connect the red wire (+) of the provided DC power supply cable to the positive
(+) terminal of the external power source, and the black wire (-) to the negative (-)
terminal of the external power source
Connect the DC power supply cable to the connector of the power cord of the main
body
Press the plug into the connector until a click sound is heard.
ヒューズ
ホルダー
Fuse
holder
Before Using
Power 電源コード
cord (DC
(direct（DC(直流)
current)
13.8 V) 13.8V）
DC
power supply
DC電源ケーブル
（付属品）
cable (accessory)
Rear
side of main body
本体後面
Red
赤色
AC
line
AC100V
コンセント
outlet
18
Direct current
13.8
V DC power
直流安定化
Black
黒色
supply
電源装置
Application for FCC / IC
FCC ID: K6620485X40
IC: 511B-20485X40
Setting Up the micro-SD Card
The following operations can be carried out by using a micro-SD card in this radio.
• Backing up the information and settings of the radio
• Saving the information in the memory channels
• Saving the settings in the set-up mode
• Saving the GPS log data
• Saving data that has been downloaded using the GM function and WIRES-X function
• Exchanging the saved data among multiple radios
Micro-SD cards that can be used
2 GB, 4 GB, 8 GB, 16 GB and 32 GB micro-SDHC cards can be used in this radio.
Cautions
zz The micro-SD or micro-SDHC cards are not provided with the product.
zz Not all micro-SD and micro-SDHC cards sold commercially are guaranteed to work with this
product.
• Do not bend the micro-SD card or place heavy objects on top of it.
• Do not touch the terminal face of the micro-SD card with your bare hands.
• Micro-SD cards that are initialized in other devices may not record normally when
used in this device. Re-initialize the micro-SD card in this radio when using a card
that has been initialized in another device. (Refer to Page xx on how to initialize the
memory card)
• Do not pull the micro-SD card out, or switch the power to the radio OFF when reading
or writing data to the card.
• Do not insert anything other than a micro-SD card into the micro-SD card slot of the
radio.
• Do not pull out or insert the micro-SD card with unreasonable force.
• When a single micro-SD card is used for a long period of time, writing and deletion of
data may become disabled. Use a new micro-SD card when data can no longer be
written or erased.
• Note that Yaesu shall not be liable for any damages suffered as a result of data loss
or corruption in use of the micro-SD card.
Before Using
Things to note when using micro-SD cards
19
Application for FCC / IC
FCC ID: K6620485X40
IC: 511B-20485X40
Setting Up the micro-SD Card
Installing the micro-SD card
1 Press
for 2 seconds or longer to switch off the
power to the main body
2 Insert the micro-SD card into the micro-SD card slot,
with the terminal face on top, until a click sound is
heard
microSD
card slot
Cautions  Insert the micro-SD card in the correct direction.
D
 o not touch the terminal of the micro-SD card
with your hands.
Before Using
Terminal
face
microSD card
After the power is switched on, the “
” icon will be
displayed at the top right of the display.
Tip
It may take a while for the icon to appear depending on
the card capacity.
Removing the micro-SD card
1 Press
for 2 seconds or longer to switch off the power to the main body
2 Push in on the microSD card
20
A click sound will be heard and the micro-SD card will be pushed outward.
Pull the micro-SD card from the micro-SD card slot
Application for FCC / IC
FCC ID: K6620485X40
IC: 511B-20485X40
Setting Up the micro-SD Card
Initializing the micro-SD card
When using a new micro-SD card, initialize the micro-SD card according to the following
procedure.
Caution
Upon initialization, all the data recorded in the micro-SD card will be erased. Check the contents of
the micro-SD card before initialization.
1 Press
for one second or longer
The set-up menu will be displayed.
The menu list will be displayed.
3 Turn the DIAL to select [4 FORMAT], then press
Before Using
2 Turn the DIAL to select [11 SD], then press
The format confirmation screen will be displayed.
4 Turn the DIAL to select [OK?], then press
The micro-SD card will be initialized.
Tip
To cancel initialization, turn the DIAL to select [Cancel],
then press
“Completed” will be displayed when initialization
is completed and the screen will then return to the
menu list.
21
Basic Operations
Application for FCC / IC
FCC ID: K6620485X40
IC: 511B-20485X40
Receiving
Turning the power on
1 Press
for 2 seconds or longer
The power will be switched on, and the display will
appear on the screen.
Tips • When switching the power on for the first time after
purchasing, or after resetting, a screen requesting
the call sign of your own station be entered, will be
displayed.
• From the second time onwards, the call sign of your
own station entered the first time will be displayed.
Switching the power off
Before Using
1 Press
for 2 seconds or longer
The screen display will disappear, and the power will be switched off.
Inputing the call sign
When switching the power on for the first time after
purchasing, or after resetting the device, a screen
requesting the call sign of your own station be entered
will be displayed.
The call sign is used to identify the transmitting station when communicating in the
digital mode.
1 Turn the DIAL to select the desired characters, then
press
Tips • Up to 10 characters (letters, numbers, and a hyphen )
can be entered.
• Refer to Page xx on how to operate the character input
screen.
2 Press
The screen will change.
Thereafter, the entered call sign is displayed at the
bottom of the power on screen, and the display will
switch to the frequency display screen (dual band
screen).
22
Application for FCC / IC
FCC ID: K6620485X40
IC: 511B-20485X40
Receiving
Switching the operating band
The two bands are displayed at the top and bottom of the dual band screen. You
can change the frequency and type of radio wave only for “operating band” which is
displayed at the lower part of the screen. The other band is called “sub-band” which is
displayed at the top part of the screen.
1 Press
Pressing each time switches the operating band
between Band A and Band B.
Adjusting the volume
Turning clockwise increases the volume whereas
turning counterclockwise decreases the volume.
Before Using
1 Turn VOL
23
Application for FCC / IC
FCC ID: K6620485X40
IC: 511B-20485X40
Receiving
Adjusting the squelch level
Annoying noises can be muted when a signal cannot be detected. Band A and Band B
squelch levels can be individually adjusted. Noise can be canceled more easily when
the squelch level is increased but it may become more difficult to pick up weak signals.
Adjust the squelch level as required.
1 Press [SQL]
The sub-band will be displayed, and the current
squelch level will be displayed on the SQL meter.
Before Using
2 Turn the DIAL to adjust the squelch level
The squelch level displayed on the sub-band display
and the level displayed on the SQL meter will be
changed.
Tip
24
If you do not perform any operation for 3 seconds after
changing the meter display or turning the DIAL, the
screen will return to the normal screen.
Application for FCC / IC
FCC ID: K6620485X40
IC: 511B-20485X40
Receiving
Tuning the radio
●●Using the knobs
1 Turn the DIAL
The frequency will increase when the knob is turned
in a clockwise direction and decrease when turned in
a counter-clockwise direction.
●●Using the microphone keys
1 Press [UP] or [DWN]
DWN
UP
Before Using
The frequency increases when [UP] is pressed, and
decreases when [DWN] is pressed.
25
Application for FCC / IC
FCC ID: K6620485X40
IC: 511B-20485X40
Communicating
Transmitting
1 Press and hold the microphone [PTT]
Keep the microphone at a distance of about 1 inch away
from the mouth when talking.
MIC
PTT
ABC
GHI
DEF
JKL
MNO
PQRS
TUV
WXYZ
P1
P3
P4
P2
DTMF MICROPHONE
MH-48
The top half of the
indicator will light red.
Before Using
3 Release [PTT]
The red bar and PO meter level will disappear and the radio will return to the
receiving state.
Tips
• Refrain from transmitting continuously for a long period of time as much as possible. The
temperature of the main body will rise and this may result in burns and equipment failure due to
overheating.
• “ERROR TX FREQ” will be displayed when attempting to transmit on a frequency that is not in the
amateur band.
26
LOCK
Tip
MIC
LAMP
The top half of the indicator will light red.
Talk directly into the microphone [MIC]
Application for FCC / IC
FCC ID: K6620485X40
IC: 511B-20485X40
Communicating
Adjusting the transmit power
When communicating with a nearby station, the transmit power can be reduced to save
on energy consumption.
1 Press
Pressing
each time switches the transmission
power in the following order.
“HI” → “LO” → “MD”
Model
HI
MD
LO
FTM-100DR
0W
20W
5W
Adjusting the sensitivity of the microphone
The sensitivity (gain) of the microphone can be adjusted.
for one second or longer
The set-up menu will be displayed.
Before Using
1 Press
2 Turn the DIAL to select [2 TX/RX], then press
The menu list will be displayed.
3 Turn the DIAL to select [2 MIC GAIN], then press
The microphone gain setting value will be displayed.
4 Turn the DIAL to select the desired microphone gain
“1 MIN” → “2 LOW” → “3 NORMAL” → “4 HIGH”
Tip
Factory default value: NORMAL
5 Press
for one second or longer
The sensitivity is set and the display returns to the previous screen.
Tip
You can also return to the previous screen by pressing
3 times.
27
Application for FCC / IC
FCC ID: K6620485X40
IC: 511B-20485X40
Communicating
Communicating in the FM mode
Choose the operating band
Select “MANUAL (FM)” as the modulation mode
Turn the DIAL to tune in to the frequency
Press and hold the microphone [PTT] to talk
Tip
You can also use the half deviation. From [2 TX/RX] → [8 HALF DEVIATION] in the set-up menu,
select “ON”.
Before Using
28
Application for FCC / IC
FCC ID: K6620485X40
IC: 511B-20485X40
Specification
●●General
TX 144 - 146 MHz or 144 - 148 MHz
430 - 440 MHz or 430 - 450 MHz
RX 108 - 137 MHz (Air Band)
137 - 174 MHz (144 MHz HAM)
174 - 400 MHz (GEN1)
400 - 480 MHz (430 MHz HAM)
480 - 999.99 MHz (GEN2)
Channel steps
5/6.25/8.33/10/12.5/15/20/25/50/100 kHz
(8.33 kHz : only for Air band)
Emission Type
F1D, F2D, F3E, F7W
Frequency stability
±2.5 ppm −4°F to +140°F (−20°C to +60°C)
Antenna impedance
50 Ω
Supply Voltage
Norminal 13.8 V DC, negative ground
Current consumption
0.5 A (receive)
11 A (50 W TX, 144 MHz)
12 A (50 W TX, 430 MHz)
Operating temperature
−4°F to +140°F (−20°C to +60°C)
Case size
Radio unit: 5.5" (W) × 1.6" (H) × 4.9" (D) (140 × 40 × 125 mm) w/o fan
Controller: 5.5" (W) × 2.8" (H) × 0.8" (D) (140 × 72 × 20 mm)
Weight (approx.)
2.64 lbs (1.2 kg) with radio unit, controller, control cable
RF power output
50/20/5 W
Modulation type
F1D, F2D, F3E : Variable Reactance Modulation
F7W : 4FSK (C4FM)
Spurious emission
At least 60 dB below
Microphone impedance
●●Transmitter
DATA terminal input impedance:
Before Using
Frequency range
About 2 kΩ
About 10 kΩ
29
Application for FCC / IC
FCC ID: K6620485X40
IC: 511B-20485X40
Specification
●●Receiver
Circuit type
Double conversion super-heterodyne
Intermediate frequencies :
A band:
1st : 47.25 MHz, 2nd :450 kHz
B band:
1st : 44.85 MHz, 2nd : 450 kHz
Receiver Sensitivity
108 - 137 MHz (AM)
137 - 140 MHz (FM)
140 - 150MHz (FM)
150 - 174 MHz (FM)
174 - 222 MHz (FM)
222 - 300 MHz (FM)
SINAD
300 - 336 MHz (AM)
336 - 420 MHz (FM)
420 - 470 MHz (FM)
470 - 520 MHz (FM)
800 - 900 MHz (FM)
900 - 999.99 MHz (FM)
Before Using
Digital mode
140 - 150 MHz (Digital)
420 - 470 MHz (Digital)
0.8μV typ for 10 dB SINAD
0.25μV for 12 dB SINAD
0.2μV typ for 12 dB SINAD
0.2μV for 12 dB SINAD
0.4μV typ for 12 dB SINAD
0.8μV typ for 12 dB SINAD
Cellular blocked (USA only)
0.19μV typ for BER 1%
0.19μV typ for BER 1%
Squelch sensitivity
0.16μV (144/430 MHz)
Selectivity
AM, FM 12 kHz/35 kHz (−6 dB/−60 dB)
AF output
3 W (8 Ω, THD10%, 13.8 V) internal speaker
8 W (4 Ω, THD10%, 13.8 V) Optional MLS-200-M10
AF output impedance
4 - 16 Ω
Strength of secondary radio waves:
4 nW and below
Cautions
zz Rated values are at normal temperature and pressure.
zz Ratings and specifications are subject to change without notice.
30
0.8μV typ for 10 dB SN
0.2μV for 12 dB SINAD
0.2μV for 12 dB SINAD
0.25μV for 12 dB SINAD
0.3μV typ for 12 dB SINAD
0.25μV typ for 12 dB
Application for FCC / IC
FCC ID: K6620485X40
IC: 511B-20485X40
Specification
Before Using
1. Changes or modifications to this device not expressly approved by YAESU MUSEN could void the
user’s authorization to operate this device.
2. This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference including received, interference that may cause undesired operation.
3. The scanning receiver in this equipment is incapable of tuning, or readily being altered, by the User
to operate within the frequency bands allocated to the Domestic public Cellular Telecommunications
Service in Part 22.
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject
to the following two conditions: (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit
pas produire de brouillage, et (2) l'utilisateur de l’appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
DECLARATION BY MANUFACTURER
The Scanner receiver is not a digital scanner and is incapable of being converted or modified to a
digital scanner receiver by any user.
WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE
SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW.
31
Application for FCC / IC
FCC ID: K6620485X40
IC: 511B-20485X40
YAESU MUSEN CO., LTD.
Tennozu Parkside Building
2-5-8 Higashi-Shinagawa, Shinagawa-ku, Tokyo
140-0002 Japan
YAESU USA
6125 Phyllis Drive, Cypress, CA 90630, U.S.A.
YAESU UK
Unit 12, Sun Valley Business Park, Winnall Close
Winchester, Hampshire, SO23 0LB, U.K.
Copyright 2015
YAESU MUSEN CO., LTD.
All rights reserved.
No portion of this manual
may be reproduced
without the permission of
YAESU MUSEN CO., LTD.
Printed in Japan
1409P-AO

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Author                          : YAESU MUSEN CO., LTD.
Create Date                     : 2015:04:08 11:19:34-04:00
Modify Date                     : 2015:04:08 11:19:47-04:00
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Metadata Date                   : 2015:04:08 11:19:47-04:00
Creator Tool                    : Adobe InDesign CS6 (Windows)
Format                          : application/pdf
Title                           : Operating Manual
Creator                         : YAESU MUSEN CO., LTD.
Document ID                     : uuid:c39619d5-c561-40cb-b1f6-c63359594649
Instance ID                     : uuid:6768ebca-77c1-40dd-bfe1-c5e320889e73
Producer                        : Adobe PDF Library 10.0.1
Page Count                      : 16

EXIF Metadata provided by EXIF.tools