Yaesu Musen 30443X3D MOBILE MARINE TRANSCEIVER User Manual GX2200 Operating Manual

Yaesu Musen Co., Ltd. MOBILE MARINE TRANSCEIVER GX2200 Operating Manual

Operating Manual 2

Download:
Mirror Download [FCC.gov]
Document ID	2127076
Application ID	bmU7Q4PhVUcc5huKfC1wFQ==
Document Description	Operating Manual 2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	271.11kB (3388813 bits)
Date Submitted	2013-11-25 00:00:00
Date Available	2014-01-09 00:00:00
Creation Date	2013-11-14 16:51:26
Producing Software	Adobe PDF Library 10.0.1
Document Lastmod	2013-11-14 16:51:45
Document Title	GX2200_Operating Manual
Document Creator	Adobe InDesign CS6 (Windows)
Document Author:	YAESU MUSEN CO., LTD.

FCC ID:K6630443X3D
IC:511B-30443X3D
!DISTRESS ALERT!
4. W h e n a D S C d i s t r e s s a c k n o w l e d g m e n t i s Nature
of:Undesignated
33 37.120 N
received, a distress alarm sounds and Channel Position:118
09.580 W
POS Time: 10:00
TX in: 02:25
16 is automatically selected. The display shows
Wait for ACK
PAUSE
CANCEL
the MMSI of the ship responding to your distress.
!DISTRESS ALERT!
RECEIVED  ACK: acknowledgment signal is Received
Acknowledged
Name:USCG
received.
ID:101234567
Since: 00:15
RECEIVED  RLY: relay signal is received from
OK
another vessel or coast
station.
5. Press the PTT switch and state your name, vessel name, number of
persons on board and the distress situation, then say âoverâ and wait for
a reply from the acknowledging ship.
6. To turn off the distress alarm before the radio retransmits the distress
call, press the 169 key.
Transmitting a DSC Distress Alert with Nature of Distress
The GX2200 is capable of transmitting a DSC distress alert with the following
âNature of Distressâ categories:
Undesignated, Fire, Flooding, Collision, Grounding, Capsizing, Sinking,
Adrift, Abandoning, Piracy, MOB
1. Press the
key. The âD S C M e n u â will
appear.
2. Rotate the CH knob to select âDISTRESS ALERT
MSGâ.
soft key. (To cancel, press the
3. Press the
soft key.) The âDISTRESS ALERT MSGâ
menu will appear on the display.
soft key, then rotate the CH
4. Press the
knob to select the desired nature of distress category.
Nature of distress categories: Fire, Flood, Collision, Grounding, Capsizing, Sinking, Adrift, Abandoning, Piracy, and MOB.
soft key.
5. Press the
6. Press and hold the DISTRESS key until a distress
alert is transmitted.
7. Perform the steps 1 through 6 of the basic operation described in the previous section.
CALL
MENU
GX2200
&5% /GPW
+PFKXKFWCN
)TQWR
#NN 5JKRU
2154GSWGUV
215 4GRQTV
&+564'55#.'46/5)
37+6
5'.'%6
&+564'55#.'46/5)
0CVWTG QH7PFGUKIPCVGF
2QUKVKQP   0
  9
215 6KOG 
2TGUU=&+564'55?UGE
HQT&+564'55VTCPUOKV
0#674'
2156/
37+6
!NATURE OF!
UNDESIGNATED
Fire
Flooding
Collision
Grounding
Capsizing
SELECT
QUIT
!NATURE OF!
Undesignated
FIRE
Flooding
Collision
Grounding
Capsizing
SELECT
QUIT
Page 51
YAESU MUSEN CO., LTD.
FCC ID:K6630443X3D
IC:511B-30443X3D
Transmitting a DSC Distress Alert with Manual Position of Input
When the GX2200 is not connected to a GPS receiver, you may input the
latitude and longitude of your vessel manually before you send a DSC
distress alert.
&5% /GPW
key. The âD S C M e n u â will +PFKXKFWCN
1. Press the
)TQWR
appear.
#NN 5JKRU
2154GSWGUV
215 4GRQTV
2. Rotate the CH knob to select âDISTRESS ALERT &+564'55#.'46/5)
37+6
5'.'%6
MSGâ.
soft key. (To cancel, press the &+564'55#.'46/5)
3. Press the
QH7PFGUKIPCVGF
soft key.) The âDISTRESS ALERT MSGâ 0CVWTG
2QUKVKQP   A
  A
menu will appear on the display.
215 6KOG 
2TGUU=&+564'55?UGE
HQT&+564'55VTCPUOKV
soft key.
4. Press the
37+6
0#674' 2156/
5. Enter UTC time in the 24-hour format and the lati- -POS/POS Time Inputtude and longitude of your vessel. Rotate the CH Position: -- --.---_
--- --.---_
knob to select the number and press the
POS Time:--:--[UTC]
soft key to move the cursor to the next character.
QUIT
ENT
BACK
You may backspace the cursor by pressing the -POS/POS Time InputPosition: 33 37.120 N
soft key if you make a mistake.
118 09.580 W
6. When you have completed your selection, press POS Time:10:00[UTC]
QUIT
ENT
BACK
soft key for two seconds to
and hold in the
save the setting.
7. Press and hold the DISTRESS key until a distress alert is transmitted.
8. Perform the steps 1 through 6 of the basic operation described in the
previous section.
CALL
MENU
Pausing a DSC Distress Call
After a DSC distress call is transmitted, the DSC distress call is repeated
every 4 minutes until the call is canceled by the user or until the radio is
turned on and off again. The GX2200 has provision to suspend (pause) the
retransmitting of the distress call by the procedure below.
1. After the distress call is transmitted, the radio will
show the top display to the right.
Looking at this display you will notice âTX in:
0 2 : 2 5 â, this is the time when the radio will
re-transmit the DSC distress call.
2. To suspend re-transmitting the DSC call, press
the
soft key.
3. To resume counting down to transmit the DSC
soft key.
Distress call, press the
Page 52
!DISTRESS ALERT!
Nature of:Undesignated
Position: 33 37.120 N
118 09.580 W
POS Time: 10:00
TX in: 02:25
Wait for ACK
PAUSE
CANCEL
!DISTRESS ALERT!
Retransmission is
now pausing!
TX in: 02:25
RESUME
CANCEL
GX2200
YAESU MUSEN CO., LTD.
FCC ID:K6630443X3D
IC:511B-30443X3D
Canceling a DSC Distress Call
If a DSC distress call was sent by error the GX2200 allows you to send a
message to other vessels to cancel the distress call that was made.
Press the
soft key, then press the
!DISTRESS ALERT!
Nature of:Undesignated
Position: 33 37.120 N
118 09.580 W
POS Time: 10:00
TX in: 02:25
Wait for ACK
PAUSE
CANCEL
soft key.
&+564'55 %#0%'.
6TCPUOKV!
;'5
01
9.3.2 Receiving a DSC Distress Call
1. When a DSC distress call is received, an emergency alarm sounds.
2. Press any key to stop the alarm.
3. The display shows the position of the vessel in
distress. To show additional information of the
vessel in distress, rotate the CH knob counter
clockwise (refer to the second display).
4GEGKXGF &+564'55
0COG
+&
5KPEG 
&+564'55 +0(1
0CVWTG QH7PFGUKIPCVG
&+56 +&
#%%'26
2#75'
37+6
4GEGKXGF &+564'55
&+56 +&
2QUKVKQP   0
  9
215 6KOG 
&+56 0/
$4)
#%%'26
2#75'
37+6
On the display you will notice 3 soft key selections. These selections are
described below:
: Press this key to accept the DSC distress call and to switch to
Channel 16.
Note: If a key is not pressed for 10 seconds or longer the radio will automatically select Channel 16.
: Press this key to temporarily disable automatic switching to
Channel 16.
: Press this key to quit the automatic Channel 16 switching and
revert to the last selected working channel.
4GEGKXGF &+564'55
soft key to enter the âWaypoint
4. Press the
0COG
+&
Inputâ menu, then enter the desired waypoint
5KPEG 
&+564'55 +0(1
QH7PFGUKIPCVG
name (up to 11 characters), described previously 0CVWTG
&+56 +&
37+6
926
(select the letter/number by rotating the CH knob
and move the cursor by pressing the
soft keys).
The ID is the MMSI from the vessel in distress.
GX2200
Page 53
YAESU MUSEN CO., LTD.
FCC ID:K6630443X3D
IC:511B-30443X3D
5. When you finish entering the waypoint name,
press and hold the
soft key to replace the
display to the waypoint screen. The display indicates the distance and direction of the distressed
vessel, and also the compass indicates the
distressed vessel by dot (ď).
6. To stop navigating to a waypoint, press one of the
soft keys, then press the
soft key. The
radio is switched to the normal mode.
9C[RQKPV+PRWV
+&
2QUKVKQP   0
  9
$#%-
16
9
$4) 6
&560/
  0
  9
4CPIG 0/ .1% #/
NOTE
You must continue monitoring Channel 16 as a coast station may
require assistance in the rescue attempt.
NOTE
When there is an unread distress alert, â â icon will appear on
the display. You may review the unread distress alert from the DSC
log, refer to the section â9.13.2 Reviewing DSC Distress Logged
Calls.â
Page 54
GX2200
YAESU MUSEN CO., LTD.
FCC ID:K6630443X3D
IC:511B-30443X3D
9.4
ALL SHIPS CALL
The all ships call function allows contact to be established with DSC
equipped vessels without having their MMSI in the individual calling directory. Also, priority for the call can be designated as âUrgencyâ or âSafetyâ.
URGENCY Call: This type of call is used when a vessel may not truly be in
distress, but have a potential problem that may lead to a
distress situation. This call is the same as saying âPAN PAN,
PAN PAN, PAN PANâ on Channel 16.
SAFETY Call: This type of call is used to transmit boating safety information to other vessels. This message usually contains information about an overdue boat, debris in the water, loss of a
navigation aid or an important meteorological message. This
call is the same as saying âSecurite, Securite, Securite.â
9.4.1 Transmitting an All Ships Call
1. Press the
key. The âDSC Menuâ will
appear.
2. Rotate the CH knob to select âAll SHIPSâ.
soft key. (To cancel, press
3. Press the
the
soft key.)
4. Rotate the CH knob to select the nature of
call (âSAFETYâ or âURGENCYâ), then press the
soft key.
5. Rotate the CH knob to select the operating
channel you want to communicate on, then
soft key.
press the
soft key to transmit the
6. Press the
selected type of all ships call.
7. After the all ships call is transmitted, the
transceiver will switch to the selected channel.
8. Listen to the channel to make sure it is not
busy, then key the microphone and say âPAN
PAN, PAN PAN, PAN PANâ or âSecurite,
Securite, Securiteâ depending on the priority of the call.
9. Press the
soft key to exit the all
ships call menu.
CALL
MENU
GX2200
&5% /GPW
+0&+8+&7#.
)TQWR
#NN 5JKRU
215 4GSWGUV
215 4GRQTV -DSC Menu&KUVTGUU#NGTV/5)
Individual
37+6
5'.'%6 Group
ALL SHIPS
POS Request
POS Report
-CategorySAFETY Auto POS Polling
QUIT
UrgencySELECT
5GNGEV +PVGTUJKR %*

SELECT





QUIT
37+6
5'.'%6
-All Ships CallCategory:Safety
CH: 06
Transmit?
QUIT
YES
-All Ships CallCategory:Safety
CH: 06
Transmiting
-All Ships CallCategory:Safety
CH: 06
Since: 00:25
QUIT
Page 55
YAESU MUSEN CO., LTD.
FCC ID:K6630443X3D
IC:511B-30443X3D
9.4.2 Receiving an All Ships Call
Received All Ships
1. When an all ships call is received, an emergency
Name:Horizon
ID:123456789
alarm will sound.
Category:Safety
CH: 06
Since: 01:03
The display shows the MMSI of the vessel transQUIT
ACCEPT
PAUSE
mitting the all ships call and the radio will change
Received All Ships
Name:Horizon
to the requested channel after 10 seconds.
ID:123456789
Category:Safety
2. Press any key to stop the alarm.
CH: 06
Since: 01:03
3. Monitor the requested channel until the all ships
QUIT
voice communication is completed.
9 75#
On the display you will notice 3 soft key selec- 51)/2
%1) 6
tions. These selections are described below:
  0

 9
: Press this key to accept the DSC all .1% 
#/
5#('6;
ships call and to switch to requested channel.
Note: If a key is not pressed for 30 seconds or longer the radio will automatically change to the requested channel.
: Press this key to temporarily disable automatic switching to the
requested channel.
Note: In some cases automatically switching to a requested channel might disrupt import ongoing communications. This feature allows
commercial users to suspend channel switching and stay on the working
channel selected before the all ships call was received.
: Press this key to quit the automatic channel switching and revert
to the last selected working channel.
key to return to the channel display.
4. Press the
06
NOTE
When there is an unread all ships call, â â icon will appear on the
display. You may review the unread all ships call from the DSC log,
refer to the section â9.13.3 Reviewing Other Logged Calls.â
Page 56
GX2200
YAESU MUSEN CO., LTD.
FCC ID:K6630443X3D
IC:511B-30443X3D
9.5
INDIVIDUAL CALL
This feature allows the GX2200 to contact another vessel with a DSC VHF
radio and automatically switch the receiving radio to a desired communications channel. This feature is similar to calling a vessel on CH16 and requesting to go to another channel (switching to the channel is private between the
two stations). Up to 80 individual contacts may be programmed.
9.5.1 Setting up the Individual / Position Call Directory
The GX2200 has a DSC directory that allows you to store a vessel or
personâs name and the MMSI (Maritime Mobile Service Identity Number)
number associated with vessels you wish to transmit individual calls, auto
polling, position request, position report, and polling transmissions.
To transmit an individual call you must program this directory with information
of the persons you wish to call, similar to a cellular phones telephone directory.
1. Press and hold the
key until âSetup
Menuâ appears.
2. Rotate the CH knob to select âDSC SETUPâ
menu.
soft key, then select
3. Press the
DIRECTORYâ
âINDIVIDUAL
with the CH
knob.
soft key.
4. Press the
5. Select âADDâ with the CH knob, then press
soft key.
the
6. Rotate the CH knob to scroll through the
first letter of the name of the vessel or
person you want to reference in the directory.
soft key to store the first
7. Press the
letter in the name and step to the next letter
to the right.
8. Repeat steps 6 and 7 until the name is
complete. The name can consist of up to
eleven characters, if you do not use all
eleven characters press the
soft key
to move to the next space. This method can
also be used to enter a blank space in the
name.
CALL
MENU
GX2200
6HWXS 0HQX
*(1(5$/ 6(783
&+ )XQFWLRQ 6HWXS
'6& 6HWXS
$,6&RPSDVV6HWXS
:D\SRLQW 6HWXS
6HWXS 0HQX
*366HWXS
*HQHUDO6HWXS
48,76HWXS
6(/(&7 &+ )XQFWLRQ
'6&6(783
$,6&RPSDVV6HWXS
:D\SRLQW 6HWXS
*366HWXS
48,7
6(/(&7
-DSC SetupINDIVIDUAL DIRECTORY
Individual Reply
Individual Ack
Individual Ring
Group -Individual
Directory
DirectoryPosition
Reply
ADD
QUIT
SELECT Edit
Delete
QUIT
SELECT
-Individual DirectoryIndividual
Name
ID:--------ENT
QUIT
BACK
-Individual DirectoryIndividual
Horizon
Name
ID:--------ENT
BACK
QUIT
Page 57
YAESU MUSEN CO., LTD.
FCC ID:K6630443X3D
IC:511B-30443X3D
If a mistake was made entering in the name repeat pressing the
soft key until the wrong character is selected, then rotate the CH knob to
correct the entry.
9. After the eleventh letter or space has been entered, press and hold the
soft key to advance to the MMSI number entry.
-Individual Directory10. Rotate the CH knob to scroll through
Individual Name
numbers, 0-9. To enter the desired number
Horizon
ID:123456789
and move one space to the right by pressing
QUIT
ENT
BACK
soft key. Repeat this procedure
the
until all nine space of the MMSI number are
entered.
If a mistake was made entering in the MMSI number repeat pressing the
soft key until the wrong number is selected, then rotate the CH
knob to correct the entry.
soft key.
11. To store the data entered, press and hold the
12. To enter another individual address, repeat steps 5 through 11.
soft key three times to return to radio operation.
13. Press the
9.5.2 Setting up the Individual Call Reply
This menu item sets up the radio to automatically (default setting) or manually respond to a DSC individual call requesting you to switch to a working
channel for voice communications. When âManualâ is selected the MMSI of
the calling vessel is shown allowing you to see who is calling. This function is
similar to caller id on a cellular phone.
6HWXS 0HQX
1. Press and hold the
key until âSetup *(1(5$/
6(783
&+ )XQFWLRQ 6HWXS
Menuâ appears.
'6& 6HWXS
$,6&RPSDVV6HWXS
2. Rotate the CH knob to select âDSC SETUPâ :D\SRLQW 6HWXS
6HWXS 0HQX
*366HWXS
*HQHUDO6HWXS
48,76HWXS
6(/(&7 &+ )XQFWLRQ
menu.
'6&6(783
$,6&RPSDVV6HWXS
soft key, then select
3. Press the
:D\SRLQW
-DSC
Setup- 6HWXS
*366HWXS
Individual
Directory
48,7
6(/(&7
âINDIVIDUAL REPLYâ with the CH knob.
INDIVIDUAL
REPLY
Individual Ack
Individual Ring
soft key.
4. Press the
Group Directory
-Individual ReplyPosition
Reply
AUTOMATIC
5. Rotate the CH knob to select âAUTOMATICâ SELECT
QUIT
Manual
or âMANUALâ.
soft key to store the
6. Press the
QUIT
ENT
selected setting.
soft key two times to return to radio operation.
7. Press the
CALL
MENU
Page 58
GX2200
YAESU MUSEN CO., LTD.
FCC ID:K6630443X3D
IC:511B-30443X3D
9.5.3 Enabling the Individual Call Acknowledgment
The radio can select either reply message âAbleâ (default) or âUnableâ when
the individual reply setting (described in the previous section) is set to
âAUTOMATICâ.
6HWXS 0HQX
1. Press and hold the
key until âSetup *(1(5$/
6(783
&+ )XQFWLRQ 6HWXS
Menuâ appears.
'6& 6HWXS
$,6&RPSDVV6HWXS
2. Rotate the CH knob to select âDSC SETUPâ :D\SRLQW 6HWXS
6HWXS 0HQX
*366HWXS
*HQHUDO6HWXS
48,76HWXS
6(/(&7 &+ )XQFWLRQ
menu.
'6&6(783
$,6&RPSDVV6HWXS
soft key, then select
3. Press the
:D\SRLQW
-DSC
Setup- 6HWXS
*366HWXS
Individual
Directory
48,7
6(/(&7
âINDIVIDUAL ACKâ with the CH knob.
Individual
Reply
INDIVIDUAL ACK
Individual Ring
soft key.
4. Press the
Group Directory
+PFKXKFWCN #EM
Position
Reply
#$.'
61 %1/2.;
5. Rotate the CH knob to select âABLE TO SELECT
QUIT
7PCDNG
COMPLYâ or âUNABLEâ.
soft key to store the
6. Press the
37+6
'06
selected setting.
soft key two times to return to radio operation.
7. Press the
CALL
MENU
9.5.4 Transmitting an Individual Call
This feature allows the user to contact another vessel with a DSC radio. This
feature is similar to calling a vessel on CH16 and requesting to go to another
channel.
Individual Call using the Individual/Position Directory
&5% /GPW
key. The âDSC Menuâ will +0&+8+&7#.
1. Press the
)TQWR
appear.
#NN 5JKRU
215 4GSWGUV
2. Rotate the CH knob to select âINDIVIDUALâ. 215 4GRQTV
+PFKXKFWCN %CNN
&KUVTGUU#NGTV/5)
*14+<10
37+6
5'.'%6 ;#'57
(To cancel, press the
soft key.)
5VCPFCTF
5WP .KIJV
soft key. The transceiver 5GNGEV $QD
3. Press the
+PVGTUJKR %*
37+6
5'.'%6 0'9 +&
will beep, and the last individual calls will 



appear.

+PFKXKFWCN %CNN

4. Rotate the CH knob to select an individual 5'.'%6
0COG*QTK\QP
37+6
+&
%CVGIQT[4QWVKPG
you want to contact.
%* 
Press the
soft key to select an indi6TCPUOKV!
37+6
;'5
vidual other than those on the display.
+PFKXKFWCN %CNN
0COG*QTK\QP
soft key, then rotate the
5. Press the
+&
%CVGIQT[4QWVKPG
CH knob to select the operating channel
%* 
you want to communicate on, then press
6TCPUOKVVKPI
the
soft key.
soft key to transmit the individual DSC signal.
6. Press the
CALL
MENU
GX2200
Page 59
YAESU MUSEN CO., LTD.
FCC ID:K6630443X3D
IC:511B-30443X3D
7. When an individual call acknowledgment is received, the established
channel is automatically changed to the channel which is selected on
step 5 above and a ringing tone sounds.
+PFKXKFWCN %CNN
soft key to listen to the
8. Press the
0COG*QTK\QP
+&
channel to make sure it is not busy, then
%CVGIQT[4QWVKPG
%* 
5KPEG 
press the microphoneâs PTT switch and talk
9CKVKPI HQT #%37+6
4'5'0&
into the microphone to the other vessel.
Individual Call by Manually Entering a MMSI
You may enter an MMSI number manually to contact without storing it in the
individual directory.
&5% /GPW
key. The âDSC Menuâ will
1. Press the
+0&+8+&7#.
)TQWR
appear.
#NN 5JKRU
+PFKXKFWCN %CNN
215 4GSWGUV
*14+<10
215 4GRQTV
2. Rotate the CH knob to select âINDIVIDUALâ.
;#'57
&KUVTGUU#NGTV/5)
37+6
5'.'%65VCPFCTF
(To cancel, press the
soft key.)
5WP .KIJV
$QD
soft key. The transceiver
3. Press the
37+6
5'.'%6 0'9 +&
will beep, and the last individual calls will
+PFKXKFWCN %CNN
/#07#.
*QTK\QP
appear.
;#'57 -Individual Call5VCPFCTF
soft key, then select
4. Press the
5WP .KIJV
Input MMSI
$QD
37+6
âMANUALâ with the CH knob.
5'.'%6
ID:--------soft key.
5. Press the
QUIT
SELECT
BACK
-Individual
Call6. Rotate the CH knob to select the first
Input MMSI
number of the MMSI which you want to
ID:345678901
soft key to
contact, then press the
QUIT
SELECT
BACK
step to the next number.
7. Repeat step 6 to set the MMSI number (nine digits).
If a mistake was made entering in the MMSI number, repeat pressing
the
key until the wrong number is selected, then rotate the CH
knob to correct the entry.
5GNGEV +PVGTUJKR %*
8. When finished entering the MMSI number,


press and hold the
soft key.



9. Rotate the CH knob to select the operating

37+6
5'.'%6
channel you want to communicate on, then
-Individual CallName:
press the
soft key.
ID:345678901
Category:Routine
soft key to transmit the
10. Press the
CH: 08
individual DSC signal.
Transmit?
CALL
MENU
YES
QUIT
11. When an individual call acknowledgment is received, the established
channel is automatically changed to the channel which is selected on
step 9 above and a ringing tone sounds.
Page 60
GX2200
YAESU MUSEN CO., LTD.
FCC ID:K6630443X3D
IC:511B-30443X3D
12. Press the
soft key to listen to the
channel to make sure it is not busy, then
press the microphoneâs PTT switch and talk
into the microphone to the other vessel.
+PFKXKFWCN %CNN
0COG
+&
%CVGIQT[4QWVKPG
%* 
5KPEG 
9CKVKPI HQT #%4'5'0&
37+6
9.5.5 Receiving an Individual Call
When an individual DSC call is received, the radio will automatically respond
(default setting) to the calling ship, and switch to the requested channel for
voice communications. Refer to section â9.5.2 Setting up the Individual Call
Replyâ to change the reply to manual if you want to see who is calling before
replying to the call.
Automatic reply:
+PFKXKFWCN
1. When an individual call is received, an individual 4GEGKXGF
0COG*QTK\QP
+&
call ringing alarm sounds.
%CVGIQT[4QWVKPG
%* 
5KPEG 
The radio automatically switches to the requested
%QPPGEVGF
37+6
channel. The display shows the MMSI of the
9
75#
vessel calling.
51)/2
2. Press any key to stop the alarm.
%1) 6
3. Press the microphoneâs PTT switch and talk into   0
  9
.1%  #/
5#('6;
the microphone to the other vessel.
4. Press the
soft key to return to radio operation.
06
Manual reply:
+PFKXKFWCN
1. When an individual call is received, an individual 4GEGKXGF
0COG*QTK\QP
+&
call ringing alarm sounds.
%CVGIQT[4QWVKPG
%* 
5KPEG 
The display shows the MMSI of the vessel transmitting the individual call and the radio will change #%%'26 2#75' 37+6
4GEGKXGF +PFKXKFWCN
0COG*QTK\QP
to the requested channel after 10 seconds.
+&
%CVGIQT[4QWVKPG
2. Press any key to stop the alarm.
%* 
5KPEG 
3. Monitor the requested channel until the message
%QPPGEVGF
37+6
is completed.
9 75#
On the display you will notice 3 soft key selec- 51)/2
%1) 6
tions. These selections are described below:
  0
  9
: Press this key to accept the DSC individ- .1%
 #/ 5#('6;
ual call and to switch to requested channel.
Note: If a key is not pressed for 30 seconds or longer the radio will automatically change to the requested channel.
06
GX2200
Page 61
YAESU MUSEN CO., LTD.
FCC ID:K6630443X3D
IC:511B-30443X3D
: Press this key to temporarily disable automatic switching to the
requested channel.
Note: In some cases automatically switching to a requested channel might disrupt import ongoing communications. This feature allows
commercial users to suspend channel switching and stay on the working
channel selected before the all ships call was received.
: Press this key to quit the automatic channel switching and revert
to the last selected working channel.
key to return to the channel display.
4. Press the
NOTE
When there is an unread individual call, â â icon will appear on the
display. You may review the unread individual call from the DSC log,
refer to the section â9.13.3 Reviewing Other Logged Calls.â
9.5.6 Setting up the Individual Call Ringer
When an individual call is received the radio will produce a ringing sound for
2 minutes. This selection allows the individual call ringer time to be changed.
1. Press and hold the
key until âSetup
Menuâ appears.
2. Rotate the CH knob to select âDSC SETUPâ
menu.
soft key, then select
3. Press the
RINGâ
âINDIVIDUAL
with the CH knob.
soft key.
4. Press the
5. Rotate the CH knob to select ringing time of
individual calls.
soft key to store the
6. Press the
selected setting.
soft key two times to
7. Press the
return to radio operation.
CALL
MENU
Page 62
6HWXS 0HQX
*(1(5$/ 6(783
&+ )XQFWLRQ 6HWXS
'6& 6HWXS
$,6&RPSDVV6HWXS
:D\SRLQW 6HWXS
6HWXS 0HQX
*366HWXS
*HQHUDO6HWXS
48,76HWXS
6(/(&7 &+ )XQFWLRQ
'6&6(783
$,6&RPSDVV6HWXS
:D\SRLQW
-DSC
Setup- 6HWXS
*366HWXS
Individual
Directory
48,7
6(/(&7
Individual
Reply
Individual Ack
INDIVIDUAL RING
Group Directory
Position Reply
QUIT
SELECT
+PFKXKFWCN 4KPI
&'(#7.6 /+0
 UGE
 UGE
 UGE
'06
37+6
GX2200
YAESU MUSEN CO., LTD.
FCC ID:K6630443X3D
IC:511B-30443X3D
The GX2200 has the capability to turn off the individual call ringer.
6HWXS 0HQX
1. Press and hold the
key until âSetup *(1(5$/
6(783
&+ )XQFWLRQ 6HWXS
Menuâ appears.
'6& 6HWXS
$,6&RPSDVV6HWXS
2. Rotate the CH knob to select âDSC SETUPâ :D\SRLQW 6HWXS
6HWXS 0HQX
*366HWXS
*HQHUDO6HWXS
48,76HWXS
6(/(&7 &+ )XQFWLRQ
menu.
'6&6(783
$,6&RPSDVV6HWXS
soft key, then select âDSC
3. Press the
:D\SRLQW
'6&
6HWXS 6HWXS
*366HWXS
,QGLYLGXDO$FN
BEEPâ with the CH knob.
48,7
6(/(&7
,QGLYLGXDO
5LQJ
*URXS 'LUHFWRU\
3RVLWLRQ 5HSO\
soft key.
4. Press the
$XWR 326 ,QWHUYDO
'6& %((3
5. Rotate the CH knob to select âIndividualâ, 6(/(&7
-DSC48,7
BeepSelect Call
soft key.
then press the
Individual
6. Rotate the CH knob to select âOffâ.
Beep
On
soft key to store the
7. Press the
QUIT
ENT
selected setting.
soft key three times to return to radio operation.
8. Press the
CALL
MENU
To re-enable the ringer tone, repeat the above procedure, rotating the CH
knob to select âOnâ in step 6 above.
GX2200
Page 63
YAESU MUSEN CO., LTD.
FCC ID:K6630443X3D
IC:511B-30443X3D
9.6
GROUP CALL
This feature allows the user to contact a group of specific vessels (e.g.
members of a yacht club) using DSC radios with group call function to automatically switch to a desired channel for voice communications. This function is very useful for yacht clubs and vessels traveling together that want
to collectively make announcements on a predetermined channel. Up to 32
group MMSIs may be programmed.
9.6.1 Setting up a Group Call
For this function to operate, the same group MMSI (Maritime Mobile Service
Identity Number) must be programmed into all the DSC VHF radios within
the group of vessels that will be using this feature. To understand Group
MMSI programming, first a ship MMSI has to be understood.
Ship MMSI: The first three digits called MID (Mobile Identity Group) of a ship
MMSI denote the country the ship registered for an MMSI. The last 6 digits
are specific to the ships ID.
Ship MMSI Example: If your MMSI is â366123456â, â366â is MID which
denote the country and â123456â is your ships MMSI.
Group MMSI:
ď˛ Group MMSI numbers are not assigned by the FCC or other organizations licensed to assign ship MMSI numbers.
ď˛ The first digit of a group MMSI is always set to â0â by International rules.
All Standard Horizon radios are preset so when programming a group
MMSI the first digit is set to â0â.
ď˛ The USCG recommends programming the MID of a ship MMSI into the
Second, Third and Fourth digits of the group MMSI as it denotes the area
the ship is located in.
ď˛ The last 5 digits are decided upon by persons in the group. This is an
important step as all radios in the group must contain the same group
MMSI so they can be contacted by each other. There is a chance that
another group of vessels may program in the same group MMSI. If this
happens, simply change one or more of the last 5 digits of the group
MMSI.
Page 64
GX2200
YAESU MUSEN CO., LTD.
FCC ID:K6630443X3D
IC:511B-30443X3D
6HWXS 0HQX
1. Press and hold the
key until âSetup *(1(5$/
6(783
&+ )XQFWLRQ 6HWXS
Menuâ appears.
'6& 6HWXS
$,6&RPSDVV6HWXS
2. Rotate the CH knob to select âDSC SETUPâ :D\SRLQW 6HWXS
6HWXS 0HQX
*366HWXS
*HQHUDO6HWXS
48,76HWXS
6(/(&7 &+ )XQFWLRQ
menu.
'6&6(783
$,6&RPSDVV6HWXS
soft key, then select
3. Press the
:D\SRLQW
-DSC
Setup- 6HWXS
*366HWXS
Individual
Directory
48,7
6(/(&7
âGROUP DIRECTORYâ with the CH knob.
Individual
Reply
Individual Ack
soft key, then select âADDâ Individual Ring
4. Press the
GROUP DIRECTORY
Position -Group
Reply Directorywith the CH knob.
QUIT
SELECT
ADD
Edit
soft key.
5. Press the
Delete
6. Rotate the CH knob to scroll through the
-Group DirectoryName
first letter of the name of the group you Group
QUIT
SELECT
want to reference in the directory.
ID:0--------Group Directorysoft key to store the first
7. Press the
QUIT
ENT
BACK
Group Name
Horizon
letter in the name and step to the next letter
ID:0-------to the right.
QUIT
ENT
BACK
8. Repeat step 6 and 7 until the name is
-Group Directorycomplete. The name can consist of up to Group Name
eleven characters, if you do not use all Horizon
eleven characters press the
soft key ID:023456789
QUIT
ENT
BACK
to move to the next space. This method can
also be used to enter a blank space in the
name.
If a mistake was made entering in the name repeat pressing the
soft key until the wrong character is selected, then rotate the CH knob to
correct the entry.
9. After the eleventh letter or space has been entered, press and hold the
soft key to advance to the group MMSI number entry.
10. Rotate the CH knob to select the second number of the MMSI (nine
digits: first digit permanently set to â0â) which you want to contact, then
soft key to step to the next number. Repeat this procepress the
dure until all eight spaces of the MMSI number are entered.
If a mistake was made entering in the MMSI number repeat pressing the
soft key until the wrong number is selected, then rotate the CH
knob to correct the entry.
soft key.
11. To store the data entered, press and hold the
12. To enter another group address, repeat steps 5 through 11.
soft key three times to return to radio operation.
13. Press the
CALL
MENU
GX2200
Page 65
YAESU MUSEN CO., LTD.
FCC ID:K6630443X3D
IC:511B-30443X3D
9.6.2 Transmitting a Group Call
Group Call using the Group Directory
&5% /GPW
key. The âDSC Menuâ will +0&+8+&7#.
1. Press the
)TQWR
appear.
#NN 5JKRU
215 4GSWGUV
2. Rotate the CH knob to select âGROUPâ. (To 215 4GRQTV &5% /GPW
&KUVTGUU#NGTV/5)
+PFKXKFWCN
37+6
5'.'%6 )4172
cancel, press the
soft key.)
#NN 5JKRU
215 4GSWGUV
soft key. The transceiver
3. Press the
215 4GRQTV
)TQWR
%CNN
&KUVTGUU#NGTV/5)
37+6
5'.'%6
will beep, and the last group calls will *14+<10
5WP.KIJV
(KUJGT
appear.
75%)
;#'57
+PVGTUJKR %*
4. Rotate the CH knob to select a group you 5'.'%6 5GNGEV

37+6
0'9 +&

want to contact.



Press the
soft key to select a group

37+6
5'.'%6
)TQWR
%CNN
other than those on the display.
0COG*14+<10
+&
soft key, rotate the CH %CVGIQT[4QWVKPG
5. Press the
%* 
knob to select the operating channel you
)TQWR %CNN
6TCPUOKV!
0COG*14+<10
37+6
+&
want to communicate on, then press the ;'5 %CVGIQT[4QWVKPG
%* 
soft key.
6TCPUOKVKPI
soft key to transmit the
6. Press the
)TQWR %CNN
group call signal.
0COG*14+<10
+&
7. When the group call signal is sent, the
%CVGIQT[4QWVKPG
%* 
5KPEG 
display will be as shown in the illustration at
37+6
the right.
8. After the group call is transmitted, all the
radios in the group will switch to the designated channel.
9. Listen to the channel to make sure it is not busy, then press the microphoneâs PTT switch and call the other vessel you desire to communicate
with.
CALL
MENU
Page 66
GX2200
YAESU MUSEN CO., LTD.
FCC ID:K6630443X3D
IC:511B-30443X3D
Group Call by Manually Entering an MMSI
This feature allows you to contact a group of vessels by entering in their
group MMSI manually.
&5% /GPW
key. The âDSC Menuâ will +PFKXKFWCN
1. Press the
)4172
appear.
#NN 5JKRU
215 4GSWGUV
2. Rotate the CH knob to select âGROUPâ. (To 215 4GRQTV )TQWR %CNN
&KUVTGUU#NGTV/5)
*14+<10
5'.'%6 5WP.KIJV37+6
cancel, press the
soft key.)
(KUJGT
75%)
soft key. The transceiver
3. Press the
;#'57
)TQWR
%CNN
/#07#.
will beep, and the last group calls will *14+<105'.'%6 0'9 +& 37+6
5WP.KIJV
(KUJGT
appear.
75%)
-Group Call;#'57
soft key, then select 5'.'%6
4. Press the
37+6
Input Group
âMANUALâ with the CH knob.
ID:0--------Group Callsoft key.
5. Press the
QUIT
SELECT
BACK
Input Group
6. Rotate the CH knob to select the first ID:034567891
5GNGEV +PVGTUJKR %*

number of the MMSI (nine digits: first digit
QUIT
SELECT 
BACK

permanently set to â0â) which you want to


soft key to
contact, then press the

37+6
5'.'%6
step to the next number.
-Group CallName:
7. Repeat step 6 to set the MMSI number.
ID:034567891
Category:Routine
If a mistake was made entering in the MMSI
CH: 08
)TQWR %CNN
Transmit?
number, repeat pressing the
soft
0COG
QUIT
YES
+&
%CVGIQT[4QWVKPG
key until the wrong number is selected,
%* 
-Group Callthen rotate the CH knob to correct the entry.
Name: 6TCPUOKVVKPI
ID:034567891
8. When finished entering the MMSI number, Category:Routine
CH: 08
Since: 00:25
press and hold the
soft key.
QUIT
9. Rotate the CH knob to select the operating
channel you want to communicate on, then
soft key.
press the
soft key to transmit the group call signal.
10. Press the
11. After the group call is transmitted, all the radios in the group will switch
to the designated channel.
12. Listen to the channel to make sure it is not busy, then press the PTT
switch and talk into the microphone to the group of vessels.
CALL
MENU
GX2200
Page 67
YAESU MUSEN CO., LTD.
FCC ID:K6630443X3D
IC:511B-30443X3D
9.6.3 Receiving a Group Call
4GEGKXGF )4172
1. When a group call is received, the GX2200 will
0COG*14+<10
+&
produce a ringing alarm sound.
%CVGIQT[5CHGV[
%* 
5KPEG 
2. The display shows the group MMSI number.
37+6
#%%'26
2#75'
3. Press any key to stop the alarm.
4. Monitor the channel for the person calling the group for a message.
On the display you will notice 3 soft key selections. These selections are
described below:
: Press this key to accept the group call and to switch to requested channel.
Note: If a key is not pressed for 30 seconds or longer the radio will automatically change to the requested channel.
: Press this key to temporarily disable automatic switching to the
requested channel.
: Press this key to quit the automatic channel switching and revert
to the last selected working channel.
4GEGKXGF )4172
5. If you want to respond, monitor the channel to
0COG*14+<10
+&
make sure it is clear, then press the microphoneâs %CVGIQT[5CHGV[
%* 
5KPEG 
PTT switch and talk into the microphone to the
37+6
group of vessels.
6. Press the
soft key to return to radio operation.
NOTE
When there is an unread group call, â â icon will appear on the
display. You may review the unread group call from the DSC log,
refer to the section â9.13.3 Reviewing Other Logged Calls.â
Page 68
GX2200
YAESU MUSEN CO., LTD.
FCC ID:K6630443X3D
IC:511B-30443X3D
9.6.4 Setting up the Group Call Ringer
The GX2200 has the capability to turn off the group call ringer.
6HWXS 0HQX
1. Press and hold the
key until âSetup *(1(5$/
6(783
&+ )XQFWLRQ 6HWXS
Menuâ appears.
'6& 6HWXS
$,6&RPSDVV6HWXS
2. Rotate the CH knob to select âDSC SETUPâ :D\SRLQW 6HWXS
6HWXS 0HQX
*366HWXS
*HQHUDO6HWXS
48,76HWXS
6(/(&7 &+ )XQFWLRQ
menu.
'6&6(783
$,6&RPSDVV6HWXS
soft key, then select âDSC
3. Press the
:D\SRLQW
'6&
6HWXS 6HWXS
*366HWXS
,QGLYLGXDO$FN
BEEPâ with the CH knob.
48,7
6(/(&7
,QGLYLGXDO
5LQJ
*URXS 'LUHFWRU\
3RVLWLRQ 5HSO\
soft key.
4. Press the
$XWR 326 ,QWHUYDO
'6& %((3
5. Rotate the CH knob to select âGroupâ, then 6(/(&7
&5%48,7
$GGR
5GNGEV %CNN
soft key.
press the
)TQWR
6. Rotate the CH knob to select âOffâ.
$GGR
1HH
soft key to store the
7. Press the
37+6
'06
selected setting.
soft key several times to return to radio operation.
8. Press the
CALL
MENU
To re-enable the ringer tone, repeat the above procedure, rotating the CH
knob to select âOnâ in step 6 above.
GX2200
Page 69
YAESU MUSEN CO., LTD.
FCC ID:K6630443X3D
IC:511B-30443X3D
9.7
POSITION REQUEST
Advancements in DSC have made it possible to poll the location of another
vessel and show the position of that vessel on the display of the GX2200.
Standard Horizon has taken this feature one step further, if any compatible GPS chart plotter is connected to the GX2200, the polled position of
the vessel is shown on the display of the GPS chart plotter making it easy
to navigate to the location of the polled vessel. This is a great feature for
anyone wanting to know the position of another vessel. For example your
buddy that is catching fish, or finding the location of a person you are cruising with.
NOTE
The other vessel must have an operating GPS receiver connected
to its DSC radio and must not have its radio set not to deny position
requests.  (Refer the section â9.5 INDIVIDUAL CALLâ to enter information into the individual directory).
9.7.1 Setting up a Position Request Reply
The GX2200 can be set up to automatically (default setting) or manually
send your position when requested by another vessel. This selection is
important if you are concerned about someone polling the position of your
vessel that you may not want to. In the manual mode you will see the MMSI
(Maritime Mobile Service Identity Number) or persons name shown on the
display allowing you to choose to send your position to the requesting vessel.
1. Press and hold the
key until âSetup Menuâ
appears.
2. Rotate the CH knob to select âDSC SETUPâ menu.
soft key, then select âPOSITION
3. Press the
REPLYâ with the CH knob.
soft key, then select âAUTOMATICâ
4. Press the
or âMANUALâ. In âAUTOMATICâ mode, after a DSC
POS request is received, the radio will automatically transmit your vesselâs position. In âMANUALâ
mode, the display of the GX2200 will show who is
requesting the position and the
soft key
on radio has to be pressed to send your position
to the requesting vessel.
CALL
MENU
6HWXS 0HQX
*(1(5$/ 6(783
&+ )XQFWLRQ 6HWXS
'6& 6HWXS
$,6&RPSDVV6HWXS
:D\SRLQW 6HWXS
*366HWXS
6HWXS 0HQX
*HQHUDO6HWXS
&+ )XQFWLRQ 6HWXS
'6&6(783
$,6&RPSDVV6HWXS
:D\SRLQW 6HWXS
*366HWXS
48,7
6(/(&7
-DSC SetupIndividual Directory
Individual Reply
Individual Ack
Individual Ring
Group Directory
POSITION REPLY
SELECT
QUIT
-Position ReplyAUTOMATIC
Manual
ENT
Page 70
48,7
6(/(&7
QUIT
GX2200
YAESU MUSEN CO., LTD.
FCC ID:K6630443X3D
IC:511B-30443X3D
5. Press the
6. Press the
soft key to store the selected setting.
soft key two times to return to radio operation.
9.7.2 Transmitting a Position Request to Another Vessel
Position Request using the Individual/Position Directory
&5% /GPW
key. The âDSC Menuâ will +0&+8+&7#.
1. Press the
)TQWR
appear.
#NN 5JKRU
215 4GSWGUV
2. R o t a t e t h e C H k n o b t o s e l e c t â P O S 215 4GRQTV &5% /GPW
&KUVTGUU#NGTV/5)
+PFKXKFWCN
37+6
5'.'%6 )TQWR
REQUESTâ, then press the
soft key.
#NN 5JKRU
215 4'37'56
3. Rotate the CH knob to select a name that
215 4GRQTV
215 4GSWGUV
%CNN
&KUVTGUU#NGTV/5)
37+6
5'.'%6
was stored in the individual/position direc- *14+<10
;#'57
5VCPFCTF
tory.
5WP .KIJV
215 4GSWGUV %CNN
$QD
soft key to select an indi- 5'.'%6 0'9 0COG*QTK\QP
Press the
37+6
+&+&
%CVGIQT[4QWVKPG
vidual other than those on the display.
6TCPUOKV!
soft key, then press the
4. Press the
37+6
;'5
soft key to transmit the position 215 4GSWGUV %CNN
0COG*QTK\QP
+&
request DSC call.
%CVGIQT[4QWVKPG
5. When the GX2200 receives the position
215 4GSWGUV %CNN
6TCPUOKVKPI
0COG*QTK\QP
from the polled vessel it is shown on the
+&
%CVGIQT[4QWVKPG
radio display and also transferred to a GPS
5KPEG 
9CKVKPI HQT #%chart plotter with NMEA DSC and DSE
37+6
4'5'0&
sentences.
soft key to return to radio operation.
6. Press the
CALL
MENU
NOTE
If the GX2200 does not receive a position data from the polled
vessel, the display will show âNO POSITION DATA.â
Position Request by Manually Entering an MMSI
This feature allows you to request the position of a vessel by manually entering the MMSI of the ship you want to ask the position.
key. The âDSC Menuâ will
1. Press the
appear.
2. R o t a t e t h e C H k n o b t o s e l e c t â P O S
REQUESTâ, then press the
soft key.
soft key.
3. Press the
CALL
MENU
&5% /GPW
+PFKXKFWCN
)TQWR
#NN 5JKRU
215 4'37'56
215 4GRQTV
215 4GSWGUV %CNN
&KUVTGUU#NGTV/5)
5'.'%6
*14+<10
5'.'%6
GX2200
37+6
;#'57
5VCPFCTF
5WP .KIJV
$QD
0'9 +&
37+6
Page 71
YAESU MUSEN CO., LTD.
FCC ID:K6630443X3D
IC:511B-30443X3D
2154GSWGUV%CNN
4. Rotate the CH knob to select âMANUAL,â then
/#07#.
*QTK\QP
press the
soft key.
;#'57
5VCPFCTF
5WP .KIJV
5. Rotate the CH knob to select the first
$QD
37+6
5'.'%6
number of the MMSI (nine digits) which you
want to contact, then press the
soft
-POS Request Callkey to step to the next number.
Input MMSI
6. Repeat step 5 to set the MMSI number.
ID:--------Request CallIf a mistake was made entering in the MMSI SELECT -POS
QUIT
BACK
Input MMSI
number, repeatedly press the
soft
ID:345678901
key until the wrong number is selected, then
QUIT
SELECT
BACK
rotate the CH knob to correct the entry.
-POS Request Call7. When finished entering the MMSI number,
Name:
ID:345678901
Category:Routine
press and hold the
soft key.
soft key to transmit the
8. Press the
215 4GSWGUV %CNN
Transmit?
0COG QUIT
YES
+&
position request DSC call.
%CVGIQT[4QWVKPG
9. When the GX2200 receives the position
5KPEG 
9CKVKPI HQT #%from the polled vessel it is shown on the
37+6
4'5'0&
radio display and also transferred to the
GPS chart plotter with NMEA DSC and
DSE sentences.
soft key to return to radio operation.
10. Press the
9.7.3 Receiving a Position Request
When a position request call is received from another vessel, a ringing alarm
sounds and the requesting vesselâs information will be shown in the display.
Operation and transceiver function differs depending on âPosition Replyâ
in the âDSC Setupâ menu setting discussed below:
Automatic reply:
1. When a position request call is received, a calling
alarm sounds 4 times. Then requested position
coordinates are transmitted automatically to the
vessel requesting your vessels position.
2. To exit from position request display, press the
Page 72
Received POS Request
Name:Horizon
ID:123456789
Category:Routine
Since: 01:03
QUIT
soft key.
GX2200
YAESU MUSEN CO., LTD.
FCC ID:K6630443X3D
IC:511B-30443X3D
Manual reply:
1. When a position request call is received from
another vessel, the display will be as shown in
the illustration at the right.
2. A ringing alarm sounds 4 times. To send your
vessels position to the requesting vessel, press
the REPLY soft key. Or to exit from position
request display, press the
soft key.
Received POS Request
Name:Horizon
ID:123456789
Category:Routine
Since: 01:03
REPLY
QUIT
Received POS Request
Name:Horizon
ID:123456789
Category:Routine
Since: 01:03
Transmitted
QUIT
9.7.4 Setting up a Position Request Ringer
The GX2200 has the capability to turn off the position request ringer.
6HWXS 0HQX
1. Press and hold the
key until âSetup *(1(5$/
6(783
&+ )XQFWLRQ 6HWXS
Menuâ appears.
'6& 6HWXS
$,6&RPSDVV6HWXS
2. Rotate the CH knob to select âDSC SETUPâ :D\SRLQW 6HWXS
6HWXS 0HQX
*366HWXS
*HQHUDO6HWXS
48,76HWXS
6(/(&7 &+ )XQFWLRQ
menu.
'6&6(783
$,6&RPSDVV6HWXS
soft key, then select âDSC
3. Press the
:D\SRLQW
'6&
6HWXS 6HWXS
*366HWXS
,QGLYLGXDO$FN
BEEPâ with the CH knob.
48,7
6(/(&7
,QGLYLGXDO
5LQJ
*URXS 'LUHFWRU\
5HSO\
soft key, then select âPOS 3RVLWLRQ
4. Press the
$XWR 326 ,QWHUYDO
'6& %((3
Requestâ with the CH knob.
48,7
6(/(&7
&5% $GGR
soft key, then select âOffâ
5. Press the
5GNGEV %CNN
2154GSWGUV
with the CH knob.
$GGR
soft key to store the
6. Press the
1HH
37+6
'06
selected setting.
7. Press the
soft key several times to return to radio operation.
CALL
MENU
To re-enable the ringer tone, repeat the above procedure, rotating the CH
knob to select âOnâ in step 5 above.
GX2200
Page 73
YAESU MUSEN CO., LTD.
FCC ID:K6630443X3D
IC:511B-30443X3D
9.8
POSITION REPORT
The feature is similar to position request, however instead of requesting a
position of another vessel this function allows you to send your position to
another vessel. Your vessel must mark the internal GPS receiver for the
GX2200 to send the position.
NOTE
To transmit a position report call, the GX2200 individual directory
must be programmed with stations you wish to send your position
to. To setup this directory refer to section â9.5.1 Setting up the Individual / Position Call Directory.â
9.8.1 Transmitting a DSC Position Report Call
DSC Position Report Call using the Individual/Position Directory
key. The âDSC Menuâ will
1. Press the
appear.
2. Rotate the CH knob to select âPOS REPORTâ.
(To cancel, press the
soft key.)
soft key.
3. Press the
4. Rotate the CH knob to select the name in
soft
the directory, then press the
key.
soft key to send your
5. Press the
position to the selected vessel.
soft key to return to radio
6. Press the
operation.
CALL
MENU
&5% /GPW
+0&+8+&7#.
)TQWR
#NN 5JKRU
&5% /GPW
215 4GSWGUV
+PFKXKFWCN
215 4GRQTV
)TQWR
&KUVTGUU#NGTV/5)
#NN 5JKRU37+6
5'.'%6
215 4GSWGUV
215 4'4146
&KUVTGUU#NGTV/5)
37+6
215 4GRQTV %CNN
/CPWCN
5'.'%6
*14+<10
;#'57
5VCPFCTF
5WP .KIJV215 4GRQTV %CNN
$QD
0COG*QTK\QP
37+6
5'.'%6
+&
%CVGIQT[4QWVKPG
215 4GRQTV %CNN
6TCPUOKV!
0COG*QTK\QP
;'5
+&
%CVGIQT[4QWVKPG
37+6
215 4GRQTV %CNN
6TCPUOKVKPI
0COG*QTK\QP
+&
%CVGIQT[4QWVKPG
5KPEG 
6TCPUOKVVGF
37+6
Page 74
GX2200
YAESU MUSEN CO., LTD.
FCC ID:K6630443X3D
IC:511B-30443X3D
DSC Position Report Call Manually Entering an MMSI
This feature allows you to send your position to another vessel by manually
entering the MMSI of the ship you want to send your position to.
&5% /GPW
key. The âDSC Menuâ will +PFKXKFWCN
1. Press the
)TQWR
appear.
#NN 5JKRU
215 4GSWGUV
2. Rotate the CH knob to select âPOS REPORTâ. 215 4'4146
&KUVTGUU#NGTV/5)
215 4GRQTV
%CNN
37+6
5'.'%6
(To cancel, press the
soft key.)
/#07#.
*QTK\QP
;#'57
soft key. The transceiver
3. Press the
5VCPFCTF
5WP .KIJV
will beep, and the POS report call menu will
$QD
37+6
5'.'%6
appear.
-POS Report Call4. Rotate the CH knob to select âMANUALâ, Input MMSI
then press the
soft key.
ID:---------POS Report Call5. Rotate the CH knob to select the first
QUIT
SELECT
BACK
Input MMSI
number of the MMSI which you want to
ID:345678901
soft key to
contact, then press the
-POS Report CallName:
QUIT
SELECT
BACK
step to the next number.
ID:345678901
Category:Routine
6. Repeat step 5 to set the MMSI number.
-POS Report CallTransmit?
Name:
If a mistake was made entering in the MMSI
QUIT
YES
ID:345678901
Category:Routine
number, repeatedly press the
soft
215 4GRQTV %CNN
key until the wrong number is selected,
0COG Transmiting
+&
then rotate the CH knob to correct the entry. %CVGIQT[4QWVKPG
5KPEG 
7. When finished entering the MMSI number,
6TCPUOKVVGF
37+6
press and hold the
soft key.
soft key to send your position to the selected vessel.
8. Press the
soft key to return to radio operation.
9. Press the
CALL
MENU
9.8.2 Receiving a DSC Position Report Call
When another vessel transmits their vessels location to the GX2200 the
following will happen:
POS REPORT
1. A ringing sound will be produced when the call is Received
Name:Horizon
ID:123456789
received and NMEA sentences (DSC, DSE) are Category:Routine
Since: 01:03
outputted so the position can be shown on a chart
-POS INFOQUIT
TO WPT
SAVE
plotter or a computer.
2. Press any key to stop ringing.
3. Rotate the CH knob to see position information of the station.
4. To exit to radio mode, press the
soft key.
GX2200
Page 75
YAESU MUSEN CO., LTD.
FCC ID:K6630443X3D
IC:511B-30443X3D
9.8.3 Navigating to a Position Report
The GX2200 has a feature that allows navigation to a received position
report call by using the compass display. Navigating to the position of a position report call may be enabled by the procedure below.
1. After the position report call has been
soft key.
received, press the
2. To start navigating using the compass
display, press and hold the
soft key
until the compass page is shown. The
display indicates the distance and direction
of the received vessel, and also the
compass indicates the received vessel by
dot (ď).
Received POS REPORT
Name:Horizon
ID:123456789
Category:Routine
Since:-Waypoint
01:03
Input-POS
WPT INFOName:Horizon
QUIT
SAVE ID:123456789
TO WPT
Position: 33 33.120N
118 06.230W
ENT
BACK
QUIT
16
25W
BRG:300 T
DST:45.0NM
33 37.120 N
118 09.580 W
Range 50NM LOC 12:56AM
9.8.4 Stopping Navigation to a Position Report
1. Press one of the soft keys to show the key selections.
2. Press the
key. The radio will stop navigating to a the waypoint and the Normal VHF display
will be shown.
16
9
$4) 6
&560/
  0
  9
5612
.+56
(70%
9.8.5 Saving a Position Report as a Waypoint
The GX2200 can save a position report call in the radioâs memory as a
waypoint.
1. After the position report call has been
soft key.
received, press the
2. Rotate the CH knob to change the first
letter in the name of the waypoint and press
the
soft key.
3. Repeat step 2 until the WPT name is
entered.
soft key to save
4. Press and hold the
the waypoint into memory.
Page 76
Received POS REPORT
Name:Horizon
ID:123456789
Category:Routine
Since: 01:03
-POS INFOTO WPT
SAVE
QUIT
-Waypoint InputWPT Name:Horizon
ID:123456789
Position: 33 33.120N
118 06.230W
ENT
BACK
QUIT
GX2200
YAESU MUSEN CO., LTD.
FCC ID:K6630443X3D
IC:511B-30443X3D
9.8.6 Navigating to a Saved Waypoint
1. Press and hold the
key until âSetup
Menuâ appears.
2. Select âGENERAL SETUPâ with the CH knob.
soft key, then select
3. Press the
âDISPLAYâ with the CH knob.
soft key
4. Press the
5. Rotate the CH knob to select âWAYPOINTâ
soft key.
and press the
6. Rotate the CH knob to select the waypoint
soft key.
name and press the
key so show the compass
7. Press the
display and to navigate to the waypoint.
The display indicates the distance and
direction of the saved waypoint, and also
the compass indicates the saved waypoint
by dot (ď).
CALL
MENU
6HWXS 0HQX
*(1(5$/ 6(783
&+ )XQFWLRQ 6HWXS
'6& 6HWXS
$,6&RPSDVV6HWXS
:D\SRLQW
6HWXS
*HQHUDO6HWXS0HQX
*366HWXS
',63/$<
48,7
6(/(&7 6HQVLWLYLW\
'LPPHU
&RQWUDVW
8QLWRI0HDVXUH
&KURNC[
0QTOCN 10($'DWD,Q2XW
48,7
6(/(&7
#+5
%QORCUU
9#;21+06
)25 5VCVWU
37+6
'06
-Waypoint DirectorySwim Point
FISHING PT
Port
SELECT
-Waypoint InputWPT Name:FISHING PT
ID:--------QUIT
Position: 33 33.120N
118 06.230W
QUIT
ENT
16
25W
BRG:300 T
DST:45.0NM
33 37.120 N
118 09.580 W
Range 50NM LOC 12:56AM
To stop the navigation to a saved waypoint, perform the steps 1 to 5 above,
except selecting âNORMALâ in the step 5.
GX2200
Page 77
YAESU MUSEN CO., LTD.
FCC ID:K6630443X3D
IC:511B-30443X3D
9.8.7 Setting up a Position Report Ringer
The GX2200 has the capability to turn off the position report ringer.
1. Press and hold the
key until âSetup
Menuâ appears.
2. Rotate the CH knob to select âDSC SETUPâ
menu.
soft key, then select âDSC
3. Press the
BEEPâ with the CH knob.
soft key, then select âPOS
4. Press the
Reportâ with the CH knob.
soft key, then select âOffâ
5. Press the
with the CH knob.
soft key to store the
6. Press the
selected setting.
CALL
MENU
7. Press the
6HWXS 0HQX
*(1(5$/ 6(783
&+ )XQFWLRQ 6HWXS
'6& 6HWXS
$,6&RPSDVV6HWXS
:D\SRLQW 6HWXS
6HWXS 0HQX
*366HWXS
*HQHUDO6HWXS
48,76HWXS
6(/(&7 &+ )XQFWLRQ
'6&6(783
$,6&RPSDVV6HWXS
:D\SRLQW 6HWXS
*366HWXS
'6&
6HWXS
48,7
6(/(&7
,QGLYLGXDO$FN
,QGLYLGXDO 5LQJ
*URXS 'LUHFWRU\
3RVLWLRQ 5HSO\
$XWR 326 ,QWHUYDO
'6& %((3
6(/(&7
48,7
&5% $GGR
5GNGEV %CNN
2154GRQTV
$GGR
1HH
'06
37+6
soft key several times to return to radio operation.
To re-enable the ringer tone, repeat the above procedure, rotating the CH
knob to select âOnâ in the step 5 above.
Page 78
GX2200
YAESU MUSEN CO., LTD.
FCC ID:K6630443X3D
IC:511B-30443X3D
9.9
MANUAL INPUT OF A GPS LOCATION (LAT/LON)
You may send the latitude and longitude of your vessel manually even if the
GX2200 is located in an area where GPS reception is limited.
After the position is entered, transmitting a DSC distress, position request, or
position report will contain the manually entered position.
6HWXS 0HQX
1. Press and hold the
key until âSetup *(1(5$/
6(783
&+ )XQFWLRQ 6HWXS
Menuâ appears.
'6& 6HWXS 6HWXS 0HQX
*HQHUDO6HWXS
$,6&RPSDVV6HWXS
)XQFWLRQ 6HWXS
6HWXS
2. Rotate the CH knob to select âGPS SETUPâ :D\SRLQW&+
'6& 6HWXS
*366HWXS
48,7
6(/(&7 $,6&RPSDVV6HWXS
menu.
:D\SRLQW 6HWXS
*366(783
48,7
6(/(&7
soft key, then select
3. Press the
*366HWXS0HQX
âPOSITION INPUTâ with the CH knob.
3LQQLQJ
7LPH 2IIVHW
$UHD
soft key. The transceiver 7LPH
4. Press the
7LPH 'LVSOD\
0DJQHWLF
will beep, and the display will be as shown 326,7,21,1387
48,7
6(/(&7
in the illustration on the right.
-POS/POS Time Input5. Enter the latitude/longitude of your vessel
Position: -- --.---_
--- --.---_
and your local UTC time in the 24-hour
POS Time:--:--[UTC]
notation by the CH knob. Rotate the CH
QUIT
ENT
BACK
knob to select the number and press the
-POS/POS Time InputPosition: 33 37.120 N
soft key to move the cursor to the
118 09.580 W
next character. You may backspace the
POS Time:10:00[UTC]
cursor by pressing the
soft key, if
QUIT
ENT
BACK
you make a mistake.
soft key to store the selected setting.
6. Press and hold the
soft key two times to return to radio operation.
7. Press the
CALL
MENU
GX2200
Page 79
YAESU MUSEN CO., LTD.
FCC ID:K6630443X3D
IC:511B-30443X3D
9.10 AUTO POS POLLING
The GX2200 has the capability to automatically track four stations
programmed into the individual directory.
The following procedure allows the time interval between position requests
to be setup.
9.10.1 Setting up the Polling Time Interval
1. Press and hold the
key until âSetup
Menuâ appears.
2. Rotate the CH knob to select âDSC SETUPâ
menu.
soft key, then select âAUTO
3. Press the
POS INTERVALâ with the CH knob.
soft key.
4. Press the
5. Rotate the CH knob to select the desired
interval time (30 second, 1, 2, 3, 4, 5, 10,
20, 30 and 40 minutes) and press the
soft key.
soft key two times to
6. Press the
return to radio operation.
CALL
MENU
6HWXS 0HQX
*(1(5$/ 6(783
&+ )XQFWLRQ 6HWXS
'6& 6HWXS
$,6&RPSDVV6HWXS
:D\SRLQW 6HWXS
6HWXS 0HQX
*366HWXS
*HQHUDO6HWXS
48,76HWXS
6(/(&7 &+ )XQFWLRQ
'6&6(783
$,6&RPSDVV6HWXS
:D\SRLQW
&5%
5GVWR 6HWXS
*366HWXS
+PFKXKFWCN4GRN[
48,7
6(/(&7
+PFKXKFWCN#EM
+PFKXKFWCN 4KPI
)TQWR &KTGEVQT[
2QUKVKQP 4GRN[
#761215+06'48#.
37+6
5'.'%6
-Auto POS Interval30 sec
1 MIN
min
min
min
min
QUIT
ENT
9.10.2 Selecting Stations to be Automatically Polled (Tracked)
NOTE
The radio uses the individual directory to select stations. Refer to
section â9.5.1 Setting up the Individual / Position Call Directoryâ
and to enter MMSI of stations you want to poll before proceeding.
1. Press the
key. The âDSC Menuâ will
appear.
2. Rotate the CH knob to select âAUTO POS
POLLINGâ, then press the
soft key.
3. Rotate the CH knob to select the âSELECT
ADDRESSâ, then press the
soft key.
4. The radio will show 4 calling stations to be
selected, select âCALL 1â and press the
soft key.
CALL
MENU
&5% /GPW
+0&+8+&7#.
)TQWR
#NN 5JKRU
215 4GSWGUV
215 4GRQTV
&5% /GPW
&KUVTGUU#NGTV/5)
)TQWR
37+6
5'.'%6
#NN 5JKRU
2154GSWGUV
215 4GRQTV
&KUVTGUU#NGTV/5)
#76121521..+0)
37+6
5'.'%6
-Auto POS PollingActivation
SELECT ADDRESS
-Auto POS PollingCALL 1:
SELECT
Call 2:
Call 3:
Call 4:
SELECT
Page 80
QUIT
CALL
QUIT
GX2200
YAESU MUSEN CO., LTD.
FCC ID:K6630443X3D
IC:511B-30443X3D
#WVQ 215 2QNNKPI
5. T h e r a d i o w i l l s h o w t h e s t a t i o n s *14+<10
programmed in the individual directory. ;#'57
(KUJGT
75%)
-Auto POS PollingRotate the CH knob to select the desired
CALL 1:HORIZON
5'.'%6 Call 2: 37+6
station and press the
soft key.
Call 3:
Call 4:
6. Repeat steps 4 and 5 for CALL 2, CALL 3
QUIT
SELECT
CALL
and CALL 4 entries.
soft key three times to exit to the radio
7. When finished, press the
mode.
9.10.3 Enabling/Disabling Auto POS Polling
1. Press the
key. The âDSC Menuâ will
appear.
2. Rotate the CH knob to select âAUTO POS
POLLINGâ, then press the
soft key.
3. Rotate the CH knob to select the âACTIVATIONâ, then press the
soft key.
4. Select âSTARTâ to enable transmissions to
the stations or âSTOPâ to disable transmissions to stations.
soft key.
5. Press the
soft key two times to
6. Press the
return to radio operation.
&5% /GPW
CALL
MENU
+0&+8+&7#.
)TQWR
#NN 5JKRU
215 4GSWGUV
215 4GRQTV &5% /GPW
&KUVTGUU#NGTV/5)
)TQWR
5'.'%6 #NN 5JKRU37+6
2154GSWGUV
215 4GRQTV
&KUVTGUU#NGTV/5)
#76121521..+0)
37+6
5'.'%6
-Auto POS PollingACTIVATION
Select Address
-Auto POS PollingSTART
SELECT
Stop
QUIT
QUIT
ENT
NOTE
When the radio receives position reports from a
called vessel the display will show the image as
in the right and also output NMEA 0183 DSC
and DSE sentences to a GPS chart plotter.
GX2200
4GEGKXGF 215 4'2.;
0COG*QTK\QP
+&
%CVGIQT[4QWVKPG
5KPEG 
215 +0(1
37+6
Page 81
YAESU MUSEN CO., LTD.
FCC ID:K6630443X3D
IC:511B-30443X3D
9.11 DSC TEST
This function is used to contact another DSC equipped vessel to ensure the
DSC functions of the radio are operating.
NOTE
To use this feature, the radio you will be transmitting the test call to
needs to have the DSC Test feature.
To perform the DSC test you will need to enter a MMSI of another vessel into
the individual directory or manually enter in the MMSI using the procedure
below.
9.11.1 Programming MMSI into Individual Directory
Refer to section â9.5.1 Setting up the Individual / Position Call Directoryâ.
9.11.2 DSC Test call by using Individual/Position Directory
1. Press the
key. The âDSC Menuâ will
appear.
2. Rotate the CH knob to select âDSC TESTâ,
then press the
soft key.
3. Rotate the CH knob to select the ship name
soft key.
and press the
soft key to transmit the
4. Press the
DSC test call to the other vessel.
soft key to return to radio
5. Press the
operation.
&5% /GPW
CALL
MENU
+0&+8+&7#.
)TQWR
#NN 5JKRU
215 4GSWGUV &5% /GPW
215 4GRQTV
215 4GSWGUV
&KUVTGUU#NGTV/5)
215 4GRQTV
37+6
5'.'%6 &KUVTGUU#NGTV/5)
#WVQ 215 2QNNKPI
&5% .QI
&5% 6'56
5'.'%6
37+6
6GUV %CNN
/#07#.
*QTK\QP
;#'57
5VCPFCTF
6GUV %CNN
5WP .KIJV
/CPWCN
$QD
*14+<10
37+6
5'.'%6 ;#'57
5VCPFCTF
5WP .KIJV
$QD
37+6
5'.'%6
6GUV %CNN
0COG*QTK\QP
+&
6GUV %CNN
0COG*QTK\QP
6TCPUOKV!
+&
37+6
;'5
5KPEG 
9CKVKPI HQT #%37+6
4'5'0&
NOTE
After the radio receives a test call reply from
the vessel that was called, the radio will ring
and show âTEST ACKâ display, which confirms
the radio you called received the test call.
Page 82
4GEGKXGF 6'56 #%0COG*QTK\QP
+&
%CVGIQT[4QWVKPG
5KPEG 
37+6
GX2200
YAESU MUSEN CO., LTD.
FCC ID:K6630443X3D
IC:511B-30443X3D
9.11.3 DSC Test Call by Manually Entering an MMSI
1. Press the
key. The âDSC Menuâ will
appear.
2. Rotate the CH knob to select âDSC TESTâ,
then press the
soft key.
3. Rotate the CH knob to select âMANUALâ and
soft key.
press the
4. Rotate the CH knob to select the first digit
soft key.
in the MMSI and press the
5. Repeat step 4 until all the numbers of the
MMSI are shown on the display.
soft key to show
6. Press and hold the
the test call page.
soft key to transmit the
7. Press the
DSC test call to the other vessel.
soft key to return to radio
8. Press the
operation.
&5% /GPW
CALL
MENU
+0&+8+&7#.
)TQWR
#NN 5JKRU
215 4GSWGUV &5% /GPW
215 4GRQTV
215 4GSWGUV
&KUVTGUU#NGTV/5)
215 4GRQTV
37+6
5'.'%6 &KUVTGUU#NGTV/5)
#WVQ 215 2QNNKPI
&5% .QI
&5% 6'56
5'.'%6
37+6
6GUV %CNN
/#07#.
*QTK\QP
;#'57
5VCPFCTF
-Test Call5WP .KIJV
$QD
Input MMSI
37+6
5'.'%6
ID:---------Test CallSELECT
QUIT
BACK
Input MMSI
ID:3456789016GUV %CNN
0COG
+&
QUIT
SELECT %CVGIQT[4QWVKPG
BACK
6TCPUOKV!
37+6
;'5
6GUV %CNN
0COG
+&
5KPEG 
9CKVKPI HQT #%37+6
4'5'0&
NOTE
After the radio receives a test call reply from
the vessel that was called, the radio will ring
and show âTEST ACKâ display, which confirms
the radio you called received the test call.
GX2200
Received TEST ACK
Name:
ID:345678901
Category:Routine
Since: 00:25
QUIT
Page 83
YAESU MUSEN CO., LTD.
FCC ID:K6630443X3D
IC:511B-30443X3D
9.12 POLLING CALL
The GX2200 has the capability to track another vessel.
9.12.1 Transmitting a Polling Call to Another Vessel
Polling Call using the Individual/Position Call Directory
1. Press the
key. The âDSC Menuâ will
appear.
2. Rotate the CH knob to select âPOLLINGâ,
then press the
soft key.
3. Rotate the CH knob to select a name that
was stored in the individual/position call
soft key.
directory, then press the
soft key to transmit the
4. Press the
polling call.
5. After a polling call is transmitted, if the reply
signal is not received, âWaiting for ACKâ
is shown on the display which means the
GX2200 is waiting for the vessel you called
to send an acknowledgement.
6. To transmit the call again, press the RESEND
soft key.
7. When an acknowledgement is received from
the polled vessel, the GX2200 will show the
display as in the right.
soft key to return to radio
8. Press the
operation.
CALL
MENU
Page 84
&5% /GPW
+0&+8+&7#.
)TQWR
#NN 5JKRU
215 4GSWGUV
215 4GRQTV &5% /GPW
215 4GRQTV
&KUVTGUU#NGTV/5)
37+6
5'.'%6 &KUVTGUU#NGTV/5)
#WVQ 215 2QNNKPI
&5% .QI
&5% 6GUV
21..+0)
5'.'%6
37+6
2QNNKPI%CNN
/CPWCN
*14+<10
;#'57
5VCPFCTF
5WP .KIJV
2QNNKPI%CNN
$QD
37+6
5'.'%6
0COG*QTK\QP
+&
%CVGIQT[4QWVKPG
6TCPUOKV!
37+6
;'5
2QNNKPI%CNN
0COG*QTK\QP
+&
%CVGIQT[4QWVKPG
5KPEG 
9CKVKPI HQT #%4'5'0&
37+6
4GEGKXGF21..+0)#%0COG*QTK\QP
+&
%CVGIQT[4QWVKPG
5KPEG 
37+6
GX2200
YAESU MUSEN CO., LTD.
FCC ID:K6630443X3D
IC:511B-30443X3D
Polling Call by Manually Entering an MMSI
This feature allows you to contact a vessel by manually entering the MMSI of
the ship you want to track.
key. The âDSC Menuâ will
1. Press the
appear.
2. Rotate the CH knob to select âPOLLINGâ,
then press the
soft key.
3. Rotate the CH knob to select âMANUALâ  and
soft key.
press the
4. Rotate the CH knob to select the first
number in the MMSI and press the
soft key.
5. Repeat step 4 until all the digits of the MMSI
are shown on the display.
6. If a mistake was made entering in the MMSI
number, repeatedly press the
soft
key until the wrong digit is selected, then
rotate the CH knob to correct the entry.
7. When finished entering the MMSI number,
press and hold the
soft key.
soft key to transmit the
8. Press the
polling call.
soft key to return to radio
9. Press the
operation.
&5% /GPW
CALL
MENU
+0&+8+&7#.
)TQWR
#NN 5JKRU
215 4GSWGUV
215 4GRQTV &5% /GPW
215 4GRQTV
&KUVTGUU#NGTV/5)
37+6
5'.'%6 &KUVTGUU#NGTV/5)
#WVQ 215 2QNNKPI
&5% .QI
&5% 6GUV
21..+0)
5'.'%6
37+6
2QNNKPI%CNN
/#07#.
*QTK\QP
;#'57
5VCPFCTF
5WP .KIJV
$QD
5'.'%6
2QNNKPI%CNN
37+6
+PRWV //5+
+&
5'.'%6
37+6
$#%-
2QNNKPI%CNN
+PRWV //5+
+&
5'.'%6
$#%-
37+6
2QNNKPI%CNN
0COG
+&
%CVGIQT[4QWVKPG
6TCPUOKV!
37+6
;'5
9.12.2 Receiving a Polling Call
When another vessel transmits a polling call to the GX2200 the following will
happen:
1. When a polling call is received, the radio will automatically respond to the calling vessel.
2. To exit from the polling call display, press the
soft key.
GX2200
2QNNKPI%CNN
0COG*QTK\QP
+&
%CVGIQT[4QWVKPG
5KPEG 
4'2.+'&
37+6
Page 85
YAESU MUSEN CO., LTD.
FCC ID:K6630443X3D
IC:511B-30443X3D
9.13 DSC LOG OPERATION
The GX2200 logs transmitted calls, received DSC distress calls, and other
calls (individual, group, all ships, etc.). The DSC log feature is similar to an
answer machine where calls are recorded for review and a â â icon will
appear on the radios display. The GX2200 can store up to 24 transmitted
calls, up to the latest 27 distress calls, and up to the latest 64 other calls
(individual, group, all ships, position report, position request ack, test call
ack, and polling calls).
NOTE
When the âDSC LOGâ menu is selected, the GX2200 may display
high-priority logged call automatically.
9.13.1 Reviewing and Resending a Transmitted Logged Call
The GX2200 allows transmitted logged calls to be reviewed and to resend
the call.
key. The âDSC Menuâ will
1. Press the
appear.
2. Rotate the CH knob to select âDSC LOGâ
menu.
3. Press the
soft key, then confirm
âTRANSMITTED LOGâ is selected.
4. Press the
soft key, then rotate the
CH knob to select the station (name or
MMSI number) you want to review and/or
resend the call.
5. Press the
soft key to review details
for the selected station.
6. Press the
soft key to resend the call
or press the
soft key to go back to
the DSC transmitted call list.
CALL
MENU
Page 86
&5% /GPW
+0&+8+&7#.
)TQWR
#NN 5JKRU
215 4GSWGUV
215 4GRQTV &5% /GPW
#NN 5JKRU
&KUVTGUU#NGTV/5)
37+6
5'.'%6 215 4GSWGUV
215 4GRQTV
&KUVTGUU#NGTV/#)
#WVQ 215 2QNNKPI
&5% .1)
5'.'%6
37+6
-DSC LogTRANSMITTED LOG
Distress Log
Other Call Log
Log Delete
6TCPUOKVVGF .QI
# 5#('6;
SELECT
# &KUVTGUU
QUIT
# ;#'57
# 
5'.'%6
37+6
-Transmitted LogALL Ships Call
Date:09/03
Time:09:50AM
Category:Safety
CH: 06
CALL
QUIT
GX2200
YAESU MUSEN CO., LTD.
FCC ID:K6630443X3D
IC:511B-30443X3D
9.13.2 Reviewing a Logged DSC Distress Call
The GX2200 allows logged DSC distress call to be reviewed.
1. Press the
key. The âD S C M e n u â will
appear.
2. Rotate the CH knob to select âDSC LOGâ menu.
soft key, then rotate the CH
3. Press the
knob to select âDISTRESS LOGâ.
soft key, then rotate the CH
4. Press the
knob to select the station (name or MMSI
number) you want to review and/or relay the
distress call to other vessels.
Note: When there is an unread received call,
â â icon will appear behind the station name (or
MMSI number).
5. Press the
soft key to review details for the
selected station.
soft key to return to radio oper6. Press the
ation.
&5% /GPW
CALL
MENU
+0&+8+&7#.
)TQWR
#NN 5JKRU
215 4GSWGUV
215 4GRQTV
&KUVTGUU#NGTV/5)
37+6
5'.'%6
&5% /GPW
#NN 5JKRU
215 4GSWGUV
215 4GRQTV
&KUVTGUU#NGTV/#)
#WVQ 215 2QNNKPI
&5% .1)
5'.'%6
37+6
-DSC LogTransmitted Log
DISTRESS LOG
Other Call Log
Log Delete
SELECT
QUIT
-Distress Log08:15
234567891
06:36
18:42
Pamle
SUN LIGHT
SELECT
QUIT
-Distress LogDistress
Name:
ID:234567891
Time:08:15
-DIST INFONature of:Undesignate
QUIT
NOTE
Not all DSC radios can receive a DSC distress relay call.
GX2200
Page 87
YAESU MUSEN CO., LTD.
FCC ID:K6630443X3D
IC:511B-30443X3D
9.13.3 Reviewing Other Logged Calls
1. Press the
key. The âDSC Menuâ will
appear.
2. Rotate the CH knob to select âDSC LOGâ
menu.
soft key, then rotate the
3. Press the
CH knob to select âOTHER CALL LOGâ.
soft key, then rotate the
4. Press the
CH knob to select the station (name or
MMSI number) you want to review and/or
call back. When there is an unread received
call, â â icon will appear behind the station
name (or MMSI number).
soft key to review details
5. Press the
for the selected station.
soft key to return to radio
6. Press the
operation.
CALL
MENU
&5% /GPW
+0&+8+&7#.
)TQWR
#NN 5JKRU
215 4GSWGUV &5% /GPW
215 4GRQTV
#NN 5JKRU
&KUVTGUU#NGTV/5)
215 4GSWGUV
37+6
5'.'%6
215 4GRQTV
&KUVTGUU#NGTV/#)
#WVQ 215 2QNNKPI
&5% .1)
5'.'%6
37+6
-DSC LogTransmitted Log
Distress Log
OTHER CALL LOG
Log Delete
1VJGT %CNN .QI
SELECT



*14+<10
QUIT
5VCPFCTF

1VJGT %CNN .QI
+PFKXKFWCN
5'.'%6
0COG*QTK\QP
+&
6KOG
%CVGIQT[5CHGV[
%* 
37+6
37+6
9.13.4 Deleting a Call from the DSC Log Directory
1. Press the
key. The âDSC Menuâ will
appear.
2. Rotate the CH knob to select âDSC LOGâ
menu.
soft key, then rotate the
3. Press the
CH knob to select âLOG DELETEâ menu.
soft key, then rotate the
4. Press the
CH knob to select the category (âTRANSMITTED LOGâ, âDISTRESS LOGâ or âOTHER
CALL LOGâ) to be deleted.
soft key, then rotate the
5. Press the
CH knob to select âALL LOG DELETEâ or
âVIEW LOG LISTâ.
1) If you want to delete all stations at a time,
select the âALL LOG DELETEâ with the
CH knob, press the
soft key.
CALL
MENU
Page 88
&5% /GPW
+0&+8+&7#.
)TQWR
#NN 5JKRU
215 4GSWGUV
215 4GRQTV
&5% /GPW
&KUVTGUU#NGTV/5)
37+6
5'.'%6 #NN 5JKRU
215 4GSWGUV
215 4GRQTV
&KUVTGUU#NGTV/#)
#WVQ 215 2QNNKPI
&5% .1)
5'.'%6
37+6
-DSC LogTransmitted Log
Distress Log
Other Call Log
LOG DELETE
SELECT
-Log DeleteTransmitted
QUITLog
DISTRESS LOG
Other Call Log
QUIT
SELECT
-Distress LogALL LOG DELETE
View Log List
SELECT
QUIT
GX2200
YAESU MUSEN CO., LTD.
FCC ID:K6630443X3D
IC:511B-30443X3D
âAll Log Deleteâ
âView Log Listâ
2) If you want to delete
&KUVTGUU .QI
-Distress Logone of the logged
08:15
234567891
&GNGVG .QI
06:36 Pamle
#NN FKTGEVQT[
18:42 SUN LIGHT
stations, select the
#TG [QWT UWTG!
âV I E W L O G L I S T â
37+6
1QUIT
DELETE
with the CH knob,
&KUVTGUU .QI
&KUVTGUU .QI
then press the
&GNGVG .QI
&GNGVG .QI
#NN FKTGEVQT[

s o f t k e y.
#TG [QWT UWTG!
%QORNGVG
Rotate the CH knob
37+6
37+6
1to select the station
&KUVTGUU .QI
&GNGVG .QI
(name or MMSI

number) to be delet%QORNGVG
ed, then press the
37+6
soft key.
3) The display will show âAre you sure?â. Press the
soft key.
soft key six times to return to radio operation.
6. Press the
GX2200
Page 89
YAESU MUSEN CO., LTD.
FCC ID:K6630443X3D
IC:511B-30443X3D
10 GENERAL SETUP
The optional CMP30 (RAM3) Remote Station Microphone can also
change the setup menu using the following procedure.
10.1 DISPLAY
The GX2200 can select additional screens other than the default   normal
(radio) display.
Refer to section â8.5 DISPLAY TYPEâ for details.
10.2 LOCAL DISTANCE RECEIVER ATTENUATOR
In some areas, signals from external sources may cause interference to
receiving marine transmissions. The GX2200 has two selections, âDistanceâ used to receive weak signals (default), and âLocalâ - which attenuates strong
signals that may be interfering with reception.
1. Press and hold the
key until âSetup Menuâ
appears.
2. Rotate the CH knob to select âGENERAL SETUPâ
menu.
soft key, then select âSENSI3. Press the
TIVITYâ with the CH knob.
soft key.
4. Press the
5. Rotate the CH knob to select âLOCALâ. The receiver sensitivity is now reduced.
soft key to store the selected
6. Press the
level.
soft key two times to return to
7. Press the
radio operation.
CALL
MENU
6HWXS 0HQX
*(1(5$/ 6(783
&+ )XQFWLRQ 6HWXS
'6& 6HWXS
$,6&RPSDVV6HWXS
:D\SRLQW 6HWXS
*366HWXS
48,7
6(/(&7
*HQHUDO6HWXS0HQX
'LVSOD\
6(16,7,9,7<
'LPPHU
&RQWUDVW
8QLWRI0HDVXUH
10($'DWD,Q2XW
6(/(&7
48,7
5GPUKVKXKV[
&+56#0%'
.QECN
'06
37+6
To return to normal sensitivity, repeat the above procedure, rotating the CH
knob to select âDISTANCEâ in step 5 above.
NOTE
In most cases, âDistanceâ should be used. If âLocalâ is selected,
remember the setting should be changed to âDistanceâ when navigating away from land to receive weak signals.
Page 90
GX2200
YAESU MUSEN CO., LTD.
FCC ID:K6630443X3D
IC:511B-30443X3D
10.3 DIMMER ADJUSTMENT
This menu selection adjusts the backlight intensity.
1. Press and hold the
key until âSetup Menuâ
appears.
2. Rotate the CH knob to select âGENERAL SETUPâ
menu.
soft key, then select âDIMMERâ
3. Press the
with the CH knob.
soft key.
4. Press the
5. Rotate the CH knob to select the desired level
(âHIGHâ is default). When âOFFâ is selected, the
lamp is turned off.
soft key to store the selected
6. Press the
level.
soft key two times to return to
7. Press the
radio operation.
6HWXS 0HQX
CALL
MENU
*(1(5$/ 6(783
&+ )XQFWLRQ 6HWXS
'6& 6HWXS
$,6&RPSDVV6HWXS
:D\SRLQW 6HWXS
*366HWXS
48,7
6(/(&7
*HQHUDO6HWXS0HQX
'LVSOD\
6HQVLWLYLW\
',00(5
&RQWUDVW
8QLWRI0HDVXUH
10($'DWD,Q2XW
48,7
6(/(&7
-DimmerHIGH
QUIT
ENT
10.4 DISPLAY CONTRAST
The display contrast can be adjusted to suit overhead or dash board installations.
1. Press and hold the
key until âSetup Menuâ
appears.
2. Rotate the CH knob to select âGENERAL SETUPâ
menu.
soft key, then select âCONTRASTâ
3. Press the
with the CH knob.
soft key.
4. Press the
5. Rotate the CHANNEL selector knob to select the
desired level. The contrast level can be set from â0â
to â31â (â15â is default).
soft key to store the selected
6. Press the
level.
soft key two times to return to
7. Press the
radio operation.
6HWXS 0HQX
CALL
MENU
GX2200
*(1(5$/ 6(783
&+ )XQFWLRQ 6HWXS
'6& 6HWXS
$,6&RPSDVV6HWXS
:D\SRLQW 6HWXS
*366HWXS
48,7
6(/(&7
*HQHUDO6HWXS0HQX
'LVSOD\
6HQVLWLYLW\
'LPPHU
&2175$67
8QLWRI0HDVXUH
10($'DWD,Q2XW
48,7
6(/(&7
-Contrast20
19
18
17
16
15
ENT
QUIT
Page 91
YAESU MUSEN CO., LTD.
FCC ID:K6630443X3D
IC:511B-30443X3D
10.8 UNIT OF MEASURE
Allows navigation and AIS displays to be shown in âKnotâ, âMile/Hourâ or
âKilo-Meter/Hourâ (for speed), âNautical Mileâ or âKilo-Meterâ (for distance),
and âFeetâ or âMeterâ (for altitude).
NOTE
GPS fix from the internal antenna or a NMEA signal from an external
GPS or chart plotter must be received.
6HWXS 0HQX
1. Press and hold the
key until âSetup Menuâ *(1(5$/
6(783
&+ )XQFWLRQ 6HWXS
appears.
'6& 6HWXS
$,6&RPSDVV6HWXS
:D\SRLQW 6HWXS
2. Rotate the CH knob to select âGPS SETUPâ menu.
*366HWXS
48,7
soft key, then rotate the CH 6(/(&7
3. Press the
*HQHUDO6HWXS0HQX
knob to select âUNIT OF MEASUREâ.
'LVSOD\
6HQVLWLYLW\
'LPPHU
soft key.
4. Press the
&RQWUDVW
81,72)0($685(
5. Rotate the CH knob to select âSPEEDâ, âDISTANCEâ, 10($'DWD,Q2XW
48,7
6(/(&7
or âALTITUDEâ which you wish to change.
-Unit of Measuresoft key, then rotate the CH SPEED
6. Press the
Distance
knob to select desired unit. Available selections Altitude
are KTS (knots), MPH (mile/hour), or KMH (kiloQUIT
SELECT
meter/hour) for speed, NM (nautical mile), SM
-Speed UnitKTS:KNOTS
(status mile) or KM (kilometer) for distance, and MPH:Mile/Hour
KMH:Kilo-Meter/Hour
FT (feet) or M (meter) for altitude.
soft key to store the selected
7. Press the
QUIT
ENT
level.
soft key three times to return to radio operation.
8. Press the
CALL
MENU
Page 92
GX2200
YAESU MUSEN CO., LTD.
FCC ID:K6630443X3D
IC:511B-30443X3D
10.9 NMEA DATA IN/OUT
This menu is used to setup the NMEA 0183 baud rate of the GPS input (Blue
and Green wires) and DSC output (Gray and Brown wires). The default
setting is 4800 bps.
When 38400 bps is selected the AIS sentences (VDM) and DSC sentences
(DSC & DSE) both are output on the Gray and Brown wires after a DSC
distress, position request or AIS transmission is received.
1. Press and hold the
key until âSetup Menuâ
appears.
2. Rotate the CH knob to select âGENERAL SETUPâ
menu.
soft key, then rotate the CH
3. Press the
knob to select âNMEA DATA IN/OUTâ.
soft key.
4. Press the
5. Rotate the CH knob to select the desired baud
rate.
soft key to store the new
6. Press the
setting.
soft key two times to return to
7. Press the
radio operation.
CALL
MENU
6HWXS 0HQX
*(1(5$/ 6(783
&+ )XQFWLRQ 6HWXS
'6& 6HWXS
$,6&RPSDVV6HWXS
:D\SRLQW 6HWXS
*366HWXS
48,7
6(/(&7
*HQHUDO6HWXS0HQX
'LVSOD\
6HQVLWLYLW\
'LPPHU
&RQWUDVW
8QLWRI0HDVXUH
10($'$7$,1287
48,7
6(/(&7
0/'#&CVC+P1WV
$25
DRU
37+6
'06
10.10 KEY BEEP
This selection is used to select the beep tone volume level when a key is
pressed.
1. Press and hold the
key until âSetup Menuâ
appears.
2. Rotate the CH knob to select âGENERAL SETUPâ
menu.
soft key, then rotate the CH
3. Press the
knob to select âKEY BEEPâ.
soft key.
4. Press the
5. Rotate the CH knob to select the desired level.
The beep level can be set from âLEVEL 1â to
âLEVEL 6â, âHIGHâ, or âOFFâ.
soft key to store the selected
6. Press the
level.
soft key two times to return to
7. Press the
radio operation.
CALL
MENU
GX2200
6HWXS 0HQX
*(1(5$/ 6(783
&+ )XQFWLRQ 6HWXS
'6& 6HWXS
$,6&RPSDVV6HWXS
:D\SRLQW 6HWXS
*366HWXS
48,7
6(/(&7
*HQHUDO6HWXS0HQX
6HQVLWLYLW\
'LPPHU
&RQWUDVW
8QLWRI0HDVXUH
10($'DWD,Q2XW
.(<%((3
6(/(&7
48,7
-Key BeepHIGH
Level
Level
Level
Level
Level
ENT
QUIT
Page 93
YAESU MUSEN CO., LTD.
FCC ID:K6630443X3D
IC:511B-30443X3D
10.11 FOG ALERT TONE FREQUENCY
The function allows the radio to be setup to send the proper fog frequency
which is dependant on vessel size, shown below:
70 - 200Hz: Vessel that are 660 feet (200 meters) or more in length
130 - 350Hz: Vessel that are 247.5 feet (75 meters) or more but less than
660 feet (200 meters) in length
250 - 525Hz: Vessel that are 66 feet (20 meters) or more but less than 247.5
feet (75 meters) in length
250 - 525Hz: Vessel that are 39.6 feet (12 meters) or more but less than 66
feet (20 meters) in length
1. Press and hold the
key until âSetup Menuâ
appears.
2. Rotate the CH knob to select âGENERAL SETUPâ
menu.
soft key, then rotate the CH
3. Press the
knob to select âFOG FREQUENCYâ.
soft key.
4. Press the
5. Rotate the CH knob to select the desired tone
frequency.
soft key to store the selected
6. Press the
level.
soft key two times to return to
7. Press the
radio operation.
CALL
MENU
6HWXS 0HQX
*(1(5$/ 6(783
&+ )XQFWLRQ 6HWXS
'6& 6HWXS
$,6&RPSDVV6HWXS
:D\SRLQW 6HWXS
*366HWXS
48,7
6(/(&7
*HQHUDO6HWXS0HQX
'LPPHU
&RQWUDVW
8QLWRI0HDVXUH
10($'DWD,Q2XW
.H\%HHS
)2*)5(48(1&<
6(/(&7
48,7
(QI(TGSWGPE[
*\
*\
*\
*\
*\
*<
'06
37+6
NOTE
By default the radio Fog frequency is set to 400Hz. In most cases
this frequency should not be changed unless the vessel is very large.
Page 94
GX2200
YAESU MUSEN CO., LTD.
FCC ID:K6630443X3D
IC:511B-30443X3D
10.12 STATION NAME
This function allows you to change the name of the radio or second station
microphone.
Example: âRadio - Cabinâ, âRAM1 - Flybridgeâ
1. Press and hold the
key until âSetup Menuâ
appears.
2. Rotate the CH knob to select âGENERAL SETUPâ
menu.
soft key, then rotate the CH
3. Press the
knob to select âSTATION NAMEâ.
soft key.
4. Press the
5. With the second station microphone connected,
rotate the CH knob to select the unit (âRadioâ or
soft
âRAM1â) to be named, then press the
key.
6. Rotate the CH knob to scroll through the first
letter of the new station name.
soft key to store the first letter
7. Press the
in the name and step to the next letter to the right.
CALL
MENU
6HWXS 0HQX
*(1(5$/ 6(783
&+ )XQFWLRQ 6HWXS
'6& 6HWXS
$,6&RPSDVV6HWXS
:D\SRLQW 6HWXS
*366HWXS
48,7
6(/(&7
*HQHUDO6HWXS0HQX
&RQWUDVW
8QLWRI0HDVXUH
10($'DWD,Q2XW
.H\%HHS
)RJ)UHTXHQF\
67$7,211$0(
6(/(&7
48,7
-Station NameSelect Unit
Radio
Unit Name
RADIO
QUIT
ENT
-Station NameSelect Unit
Radio
Unit Name
Cabin
ENT
BACK
QUIT
8. Repeat step 6 and 7 until the name is complete.
The name can consist of up to eight characters, if you do not use all
eight characters press the
soft key to move to the next space.
This method can also be used to enter a blank space in the name. If a
mistake was made entering in the name repeatedly press the
soft key until the wrong character is selected, then rotate the CH knob to
correct the entry.
soft key to enter the name.
9. Press and hold the
10. If you want to enter the name of the other connected RAM3 or radio,
repeat steps 5 through 9.
soft key three times to return to radio operation.
11. Press the
GX2200
Page 95
YAESU MUSEN CO., LTD.
FCC ID:K6630443X3D
IC:511B-30443X3D
10.13 SOFT KEYS
This menu item allows selection of the number of soft keys, soft key selection
and how long the display will show the soft key icon after a soft key is pressed.
6HWXS 0HQX
1. Press and hold the
key until âSetup *(1(5$/
6(783
&+ )XQFWLRQ 6HWXS
Menuâ appears.
'6& 6HWXS
$,6&RPSDVV6HWXS
*HQHUDO6HWXS0HQX
6HWXS
2. Rotate the CH knob to select âGENERAL :D\SRLQW8QLWRI0HDVXUH
*366HWXS
10($'DWD,Q2XW
6(/(&7 .H\%HHS 48,7
SETUPâ menu.
)RJ)UHTXHQF\
6WDWLRQ1DPH
soft key, then rotate the
3. Press the
62)7.(<6
48,7
6(/(&7
CH knob to select âSOFT KEYSâ.
5QHV -G[U
07/$'4 1( 51(6 -';5
soft key, then rotate the -G[#UUKIPOGPV
4. Press the
-G[6KOGT
CH knob to âNUMBER OF SOFT KEYSâ.
-Number of Soft Keyssoft key, then rotate the 5'.'%6 3
5. Press the
37+6
CH knob to select the number of soft keys
(3 through 10).
QUIT
ENT
5QHV
-G[U
soft key, then rotate the 0WODGT QH 5QHV
6. Press the
-G[U
-';#55+)0/'06
CH knob to âKEY ASSIGNMENTâ (to change -G[6KOGT
the use of selected soft keys).
-Assignment37+6
5'.'%6 [KEY 1]:SCAN
soft key.
7. Press the
[Key 2]:DW
[Key
3]:WX
8. Rotate the CH knob to select the key (âKEY1â,
âKEY2â, or âKEY3â) to be programmed, and
QUIT
SELECT
-G[#UUKIPOGPV
soft key.
press the
010'
&+//'4
5%#0
9. Rotate the CH knob to select the new func- &9
+%
tion to be assigned, and press the
2#(1)
37+6
'06
soft key. Available functions are listed in the
next page. Repeat steps 8 and 9 to program
the other soft keys.
5QHV -G[U
key, then rotate the CH
10. Press the
0WODGT QH 5QHV -G[U
-G[#UUKIPOGPV
knob to select âKEY TIMERâ (selects how
-';6+/'4
long the soft key icon will be shown on the
-G[6KOGT
 UGE
37+6
5'.'%6
display after a soft key is pressed; default  UGE
5'%
 UGE
is 5 seconds). Then, press the
soft  UGE
 UGE
37+6
key.
'06
11. Rotate the CH knob to select the time.
soft key to store the selected setting.
12. Press the
soft key three times to return to radio operation.
13. Press the
CALL
MENU
Page 96
GX2200
YAESU MUSEN CO., LTD.
FCC ID:K6630443X3D
IC:511B-30443X3D
DISPLAY
DIMMER
SCAN
DW
IC
PA/FOG
CPS: COMPASS
WPT
AIS
AIS AL
PRESET
MARK
PSET 0 - PSET 9
GX2200
FUNCTION
Select the menu for the display and key back light intensity
Starts and stops scanning.
Starts and stops dual watch scan.
Activates intercom between radio and RAM3 mic (optional RAM3 required).
Activates the PA / Fog Horn function.
Shows the âCompassâ display.
Shows the âWaypointâ navigation display.
Shows the âAISâ display.
Toggles the AIS alarm âonâ and âoffâ.
Porgrams or deletes the preset memory channel.
Mark the current position for a âWaypointâ.
Immediately recalls the preset memory channel.
Page 97
YAESU MUSEN CO., LTD.
FCC ID:K6630443X3D
IC:511B-30443X3D
11 CHANNEL FUNCTION SETUP
11.1 CHANNEL GROUP
This section selects a channel group from USA, Canada, and International.
Refer to section â8.6 USA, CANADA, AND INTERNATIONAL MODEâ for
details.
11.2 SCAN MEMORY
To be able to scan channels the radio must be programmed. This section
allows channels to be stored in scan memory.
Refer to section â8.9.2 Programming Scan Memoryâ for details.
11.3 SCAN TYPE
This selection is used to select the scan mode between âMemory Scanâ and
âPriority Scanâ.  The default setting is âPriority Scanâ.
Refer to section â8.9.1 Selecting the Scan Typeâ for details.
11.4 SCAN RESUME
This selection is used to select the time the GX2200 waits after a transmission ends before the radio start to scan channels again. The default setting is
2 seconds.
1. Press and hold the
key until âSetup Menuâ
appears.
2. Rotate the CH knob to select âCH FUNCTION
SETUPâ.
soft key, then select âS C A N
3. Press the
RESUMEâ with the CH knob.
soft key.
4. Press the
5. Rotate the CH knob to select the desired resume
time, default is 2 seconds. The resume time can
be set to â1SECâ through â5SECâ or âOffâ. In the âOffâ
selection, the scanner will resume after the other
station stops transmitting (carrier drops).
soft key to store the new
6. Press the
setting.
soft key several times to return
7. Press the
to radio operation.
CALL
MENU
Page 98
6HWXS 0HQX
*(1(5$/ 6(783
&+ )XQFWLRQ 6HWXS
'6& 6HWXS
$,6&RPSDVV6HWXS
:D\SRLQW 6HWXS
*366HWXS
48,7
6(/(&7
6HWXS 0HQX
*HQHUDO6HWXS
&+)81&7,216(783
'6& 6HWXS
$,6&RPSDVV6HWXS
:D\SRLQW 6HWXS
*366HWXS
48,7
6(/(&7
&+ )XQFWLRQ 6HWXS
&+ *URXS
6FDQ 0HPRU\ &+
6FDQ 7\SH
6&$1 5(680(
3ULRULW\ &+
6HFRQG&+
6(/(&7
48,7
-Scan Resume5 sec
4 sec
3 sec
2 SEC
1 sec
Off
ENT
QUIT
GX2200
YAESU MUSEN CO., LTD.
FCC ID:K6630443X3D
IC:511B-30443X3D
11.5 PRIORITY CHANNEL
By default the radio priority channel is set to Channel 16. This procedure
allows the radio to use a different priority channel used when priority scanning.
1. Press and hold the
key until âSetup Menuâ
appears.
2. Rotate the CH knob to select âCH FUNCTION
SETUPâ.
soft key, then select âPRIORITY
3. Press the
CHâ with the CH knob.
soft key.
4. Press the
5. Rotate the CH knob to select the desired channel
to be a priority.
soft key to store the new
6. Press the
setting.
soft key two times to return to
7. Press the
radio operation.
6HWXS 0HQX
CALL
MENU
*(1(5$/ 6(783
&+ )XQFWLRQ 6HWXS
'6& 6HWXS
$,6&RPSDVV6HWXS
:D\SRLQW 6HWXS
*366HWXS
48,7
6(/(&7
6HWXS 0HQX
*HQHUDO6HWXS
&+)81&7,216(783
'6& 6HWXS
$,6&RPSDVV6HWXS
:D\SRLQW 6HWXS
*366HWXS
48,7
6(/(&7
&+ )XQFWLRQ 6HWXS
&+ *URXS
6FDQ 0HPRU\ &+
6FDQ 7\SH
6FDQ 5HVXPH
35,25,7< &+
6HFRQG&+
48,7
6(/(&7
-Priority CH20A
20
19A
18A
17
16
ENT
QUIT
11.6 SECOND CHANNEL
*************************
1. Press and hold the
key until âSetup Menuâ
appears.
2. Rotate the CH knob to select âCH FUNCTION
SETUPâ.
soft key, then select âSECOND
3. Press the
CHâ with the CH knob.
soft key.
4. Press the
5. Rotate the CH knob to select the desired channel.
soft key to store the new
6. Press the
setting.
soft key two times to return to
7. Press the
radio operation.
6HWXS 0HQX
CALL
MENU
*(1(5$/ 6(783
&+ )XQFWLRQ 6HWXS
'6& 6HWXS
$,6&RPSDVV6HWXS
:D\SRLQW 6HWXS
*366HWXS
6(/(&7
&+)81&7,216(783
'6& 6HWXS
$,6&RPSDVV6HWXS
:D\SRLQW 6HWXS
*366HWXS
6(/(&7
48,7
&+ )XQFWLRQ 6HWXS
&+ *URXS
6FDQ 0HPRU\ &+
6FDQ 7\SH
6FDQ 5HVXPH
3ULRULW\ &+
6(&21'&+
6(/(&7


$

$
$
(17
GX2200
48,7
6HWXS 0HQX
*HQHUDO6HWXS
48,7
6HFRQG&+
48,7
Page 99
YAESU MUSEN CO., LTD.
FCC ID:K6630443X3D
IC:511B-30443X3D
11.7 WEATHER ALERT
Enables/disables the NOAA Weather Alert function. The default setting is
âONâ.
1. Press and hold the
key until âSetup Menuâ
appears.
2. Rotate the CH knob to select âCH FUNCTION
SETUPâ.
soft key, then select âWX ALERTâ
3. Press the
with the CH knob.
soft key.
4. Press the
5. Rotate the CH knob to select âONâ or âOFFâ.
soft key to store the selected
6. Press the
level.
soft key two times to return to
7. Press the
radio operation.
6HWXS 0HQX
CALL
MENU
*(1(5$/ 6(783
&+ )XQFWLRQ 6HWXS
'6& 6HWXS
$,6&RPSDVV6HWXS
:D\SRLQW 6HWXS
*366HWXS
48,7
6(/(&7
6HWXS 0HQX
*HQHUDO6HWXS
&+)81&7,216(783
'6& 6HWXS
$,6&RPSDVV6HWXS
:D\SRLQW 6HWXS
*366HWXS
48,7
6(/(&7
&+ )XQFWLRQ 6HWXS
6FDQ 0HPRU\ &+
6FDQ 7\SH
6FDQ 5HVXPH
3ULRULW\ &+
6HFRQG&+
:;$/(57
6(/(&7
48,7
-WX AlertON
Off
QUIT
ENT
11.8 CHANNEL NAME
When the radio (âNormalâ) mode is selected, the display will show a name
under the channel number. This name describes the use of the channel. The
radio has the capability to customize the name by the procedure below.
Example: CH69 PLEASURE to HOOKUP
1. Press and hold the
key until âSetup Menuâ
appears.
2. Rotate the CH knob to select âCH FUNCTION
SETUPâ.
soft key, then select âCH NAMEâ
3. Press the
with the CH knob.
soft key.
4. Press the
CALL
MENU
6HWXS 0HQX
*(1(5$/ 6(783
&+ )XQFWLRQ 6HWXS
'6& 6HWXS
$,6&RPSDVV6HWXS
:D\SRLQW 6HWXS
*366HWXS
6(/(&7
48,7
6HWXS 0HQX
*HQHUDO6HWXS
&+)81&7,216(783
'6& 6HWXS
$,6&RPSDVV6HWXS
:D\SRLQW 6HWXS
*366HWXS
6(/(&7
48,7
&+ )XQFWLRQ 6HWXS
6FDQ 7\SH
6FDQ 5HVXPH
3ULRULW\ &+
6HFRQG&+
:;$OHUW
&+ 1$0(
6(/(&7
Page 100
48,7
GX2200
YAESU MUSEN CO., LTD.

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : Yes
Author                          : YAESU MUSEN CO., LTD.
Create Date                     : 2013:11:14 16:51:26+09:00
Modify Date                     : 2013:11:14 16:51:45+09:00
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Metadata Date                   : 2013:11:14 16:51:45+09:00
Creator Tool                    : Adobe InDesign CS6 (Windows)
Format                          : application/pdf
Title                           : GX2200_Operating Manual
Creator                         : YAESU MUSEN CO., LTD.
Document ID                     : uuid:c8bcfd9a-8e84-4da0-80cf-2c34def5f09d
Instance ID                     : uuid:e92564ee-bbc8-4564-978a-3871c2333843
Producer                        : Adobe PDF Library 10.0.1
Page Count                      : 50

EXIF Metadata provided by EXIF.tools

Yaesu Musen 30443X3D MOBILE MARINE TRANSCEIVER User Manual GX2200 Operating Manual

Yaesu Musen Co., Ltd. MOBILE MARINE TRANSCEIVER GX2200 Operating Manual

Contents

Operating Manual 2

FCC ID Filing: K6630443X3D

Navigation menu

Namespaces

Views

Navigation