Yaesu Musen 30453X20 PORTABLE MARINE TRANSCEIVER User Manual HX290 pmd
Yaesu Musen Co., Ltd. PORTABLE MARINE TRANSCEIVER HX290 pmd
Users Manual
FCC ID:K6630453X20 / IC: 511B-30453X20 HX290 Floating Marine Transceiver Owner’s Manual HX290 Page 1 Vertex Standard Co., Ltd. FCC ID:K6630453X20 / IC: 511B-30453X20 TABLE OF CONTENTS QUICK REFERENCE GUIDE ........................................................................................................ 3 1. GENERAL INFORMATION .................................................................................................... 4 1.1 INTRODUCTION ......................................................................................................... 4 4.2 RF EXPOSURE SAFETY STATEMENT ................................................................... 4 2. ACCESSORIES ...................................................................................................................... 5 2.1 PACKING LIST ........................................................................................................... 5 2.2 OPTIONS ..................................................................................................................... 5 3. ABOUT THIS RADIO ............................................................................................................ 6 3.1 ABOUT THE VHF MARINE BAND .......................................................................... 6 3.2 ABOUT WATER RESISTANCE ................................................................................. 6 3.3 DISTRESS AND HAILLING (CHANNEL 16) ............................................................ 6 3.4 CALLING ANOTHER VESSEL (CHANNEL 16 OR 9) ............................................ 7 3.5 OPERATING ON CHANNEL 13 ............................................................................... 8 3.6 OPERATING ON CHANNEL 67 ............................................................................... 8 3.7 SIMPLEX/DUPLEX CHANNEL USE ......................................................................... 8 4. GETTING STARTED ............................................................................................................ 10 4.1 RADIO CARE ............................................................................................................ 10 4.2 BELT CLIP INSTALLATION AND REMOVAL ........................................................ 10 4.3 BATTERIES AND CHARGERS ............................................................................... 11 4.3.1 BATTERY SAFETY ....................................................................................... 11 4.3.2 BATTERY INSTALLATION / REMOVAL ....................................................... 12 4.3.3 BATTERY CHARGING ................................................................................. 13 5. CONTROLS AND INDICATORS ......................................................................................... 14 5.1 CONTROLS AND SWITCHES ................................................................................ 14 5.2 LCD INDICATORS .................................................................................................... 17 6. BASIC OPERATION ............................................................................................................ 18 6.1 PROHIBITED COMMUNICATIONS ......................................................................... 18 6.2 INITIAL SETUP ......................................................................................................... 18 6.3 RECEPTION .............................................................................................................. 18 6.4 TRANSMISSION ....................................................................................................... 19 6.4.1 TRANSMIT TIME-OUT TIMER (TOT) ........................................................... 19 6.5 USA, CANADA, AND INTERNATIONAL CHANNELS .............................................. 20 6.6 KEYPAD LOCKING .................................................................................................. 20 6.7 NOAA WEATHER CHANNELS ............................................................................... 21 6.7.1 NOAA WEATHER ALERT ............................................................................. 21 6.7.2 NOAA WEATHER ALERT TESTING ............................................................ 21 6.8 PRESET CHANNELS (0 ~ 9): INSTANT ACCESS ................................................ 22 6.8.1 PROGRAMMIMG ......................................................................................... 22 6.8.2 OPERATION ................................................................................................. 22 6.9 SCANNING ................................................................................................................ 23 6.9.1 SELECTING THE SCAN TYPE .................................................................... 23 6.9.2 PROGRAMMING SCAN MEMORY ............................................................ 24 6.9.3 MEMORY SCANNING (M-SCAN) ................................................................ 24 6.9.4 PRIORITY SCANNING (P-SCAN) ................................................................ 24 6.10 DUAL WATCH ........................................................................................................... 25 7. MENU (“SET”) MODE .......................................................................................................... 26 8. MAINTENANCE .................................................................................................................... 28 8.1 GENERAL .................................................................................................................. 28 8.2 REPLACEMENT PARTS .......................................................................................... 28 8.3 TROUBLESHOOTING CHART ................................................................................ 29 9. VHF MARINE CHANNEL ASSIGNMENT .......................................................................... 30 10. WARRANTY .......................................................................................................................... 36 11. INSTALLATION OF OPTION .............................................................................................. 39 11.1 FBA-42 ALKALINE BATTERY CASE ........................................................................ 39 12. SPECIFICATIONS ................................................................................................................. 40 12.1 GENERAL .................................................................................................................. 40 12.2 TRANSMITTER ......................................................................................................... 40 12.3 RECEIVER ................................................................................................................ 40 13. FCC & CANADA RADIO LICENSE INFORMATION ....................................................... 41 14. FCC NOTICE ....................................................................................................................... 42 Page 2 HX290 Vertex Standard Co., Ltd. FCC ID:K6630453X20 / IC: 511B-30453X20 QUICK REFERENCE GUIDE This transceiver is equipped with the E2O (Easy-To-Operate) system. You can do the basic operation in numerical order of the illustration below. [PWR/VOL] KNOB Rotate this knob clockwise to turn on the radio, and adjust the audio level. [PTT] SWITCH MIC Speak into the microphone in a normal voice level while pressing this switch. When transmitting, position your mouth 1 inch (2.5 cm) away from the small mic hole. Speak slowly and clearly into the microphone. [16/9] BUTTON Press to recall channel 16. Press and hold to recall channel 9. [H/L( [SQL] BUTTON )] BUTTON Press this key first, then press the [ ] key to squelch or press the [] key to un-squelch the radio. Press to toggle the transmit power between High (5W) and Low (1W). []/[] BUTTONS Selects the operating channel. NOTE For additional details, refer to next page or section “5. CONTROLS AND INDICATORS”. HX290 Page 3 Vertex Standard Co., Ltd. FCC ID:K6630453X20 / IC: 511B-30453X20 1. GENERAL INFORMATION 1.1 INTRODUCTION Congratulations on your purchase of the HX290! The HX290 is a JIS-8/IPX8 Submersible Floating 5-Watt portable two way marine transceiver. The transceiver has all allocated USA, International, or Canadian channels. It has emergency channel 16 which can be immediately selected from any channel by pressing the key. NOAA (National Oceanic and Atmospheric Administration) Weather channels can also be accessed immediately by pressing and holding the key. The HX290 includes the following features: 10 Programmable Preset Channels, Memory, Priority, Dual Watch Scanning, NOAA Weather Alert, easy-toread large LCD display, EEPROM memory back-up, Battery Life displayed on LCD, Glow-In-The-Dark strip, and a transmit Time-Out Timer (TOT). The HX290 transmitter provides a full 5 Watt of transmit power and also is selectable to 1 Watt to assist the user in ensuring maximum battery life. JIS-8/IPX8: 1.5 m (about 5Ft) for 30 minutes 1.2 RF EXPOSURE SAFETY STATEMENT Your wireless handheld portable transceiver contains a low power transmitter. When the Push-to-Talk (PTT) button is pushed, the transceiver sends out radio frequency (RF) signals. In August 1996, the Federal Communications Commission adopted RF exposure guidelines with safety levels for hand-held wireless devices. This device is authorized to operate at a duty factor not to exceed 50% (this corresponds to 50% transmission time and 50% reception time). WARNING: To maintain compliance with the FCC’s RF exposure guidelines, this transmitter and its antenna must maintain a separation distance of at least 1 inch (2.5 centimeters) from your face. Speak in a normal voice, with the antenna pointed up and away from the face at the required separation distance. In order to comply with FCC/IC RF Exposure requirements for body-worn operations, this radio must be utilized with the supplied belt-clip accessory (Vertex Part No. CLIP-22). Use only the supplied antenna. Unauthorized antennas, modifications, or attachments could damage the transmitter, and may violate FCC regulations. Page 4 HX290 FCC ID:K6630453X20 / IC: 511B-30453X20 2. ACCESSORIES 2.1 PACKING LIST When the package containing the transceiver is first opened, please check it for the following contents: HX290 Transceiver CAT460 Antenna FNB-110LI 7.4 V, 1170 mAh Li-Ion Battery Pack CD-52 Charger Cradle for HX290 PA-44B 120VAC Wall Charger for CD-52 E-DC-19A DC Cable with 12 V Cigarette Lighter Plug CLIP-22 Belt Clip Hand Strap Owner’s Manual 2.2 OPTIONS MH-73A4B MH-57A4B VC-24 VC-27 CN-3 CD-52 FNB-110LI FBA-42 PA-44B/C/U E-DC-19A Speaker/Microphone Mini Speaker/Microphone VOX Headset Earpiece/Microphone Radio-to-Ship’s Antenna Adapter Charger Cradle 7.4 V, 1170 mAh Li-Ion Battery Pack Alkaline Battery Case AC Wall Charger for the CD-52 DC Cable with 12 V Cigarette Lighter Plug : “B” suffix is for use with 120 VAC (Type-A plug), “C” suffix is for use with 230 VAC (Type-C plug), and “U” suffix is for use with 230 VAC (Type-BF plug). Note: Before operating the HX290 for the first time, it is recommended that the battery be charged. Please see section “4.3.3 BATTERY CHARGING” for details. HX290 Page 5 Vertex Standard Co., Ltd. FCC ID:K6630453X20 / IC: 511B-30453X20 3. ABOUT THIS RADIO 3.1 ABOUT THE VHF MARINE BAND The radio frequencies used in the VHF marine band lie between 156 and 162 MHz. The marine VHF band provides communications over distances that are essentially “Line of sight” Actual transmission range depends much more on antenna type, gain and height than on the power output of the transmitter. On a fixed mount 25 W radio transmission expected distances can be greater than 15 miles, for a portable 5 W radio transmission the expected distance can be greater than 5 miles in “Line of sight”. The user of a Marine VHF radio is subject to severe fines if the radio is used on land. The reasoning for this is you may be near an inland waterway, or propagation anomalies may cause your transmission to be heard in a waterway. If this occurs, depending upon the marine VHF channel on which you are transmitting, you could interfere with a search and rescue case, or contribute to a collision between passing ships. For VHF Marine channel assignments refer to section “9”. WARNING This radio is capable of transmitting on Marine VHF. The FCC allows the use of VHF Marine band on water areas only. However the FCC does not allow the use of the VHF Marine band when on land. If persons use the VHF Marine Band on land and interfere with others communicating, the FCC will be notified and search for the interference. Responsible parties found to be transmitting on the VHF Marine Band on land could be fined up to $10,000 for the first offense. 3.2 ABOUT WATER RESISTANCE Water resistance of the transceiver is ensured only when the battery pack is attached to the transceiver and MIC/SP cap is installed in the MIC/SP jack. 3.3 DISTRESS AND HAILLING (CHANNEL 16) Channel 16 is known as the Hail and Distress Channel. An emergency may be defined as a threat to life or property. In such instances, be sure the transceiver is on and set to “Channel 16”. Then use the following procedure: ) switch and say “Mayday, Mayday, May1. Press the PTT (Push-To-Talk: day. This is _____, _____, _____” (your vessel’s name). 2. Then repeat once: “Mayday, _____” (your vessel’s name). 3. Now report your position in latitude/longitude, or by giving a true or magnetic bearing (state which) to a well-known landmark such as a navigation Page 6 HX290 Vertex Standard Co., Ltd. FCC ID:K6630453X20 / IC: 511B-30453X20 aid or geographic feature such as an island or harbor entry. 4. Explain the nature of your distress (sinking, collision, aground, fire, heart attack, life-threatening injury, etc.). 5. State the kind of assistance your desire (pumps, medical aid, etc.). 6. Report the number of persons aboard and condition of any injured. 7. Estimate the present seaworthiness and condition of your vessel. 8. Give your vessel’s description: length, design (power or sail), color and other distinguishing marks. The total transmission should not exceed 1 minute. 9. End the message by saying “OVER”. Release the PTT ( ) switch and listen. 10. If there is no answer, repeat the above procedure. If there is still no response, try another channel. 3.4 CALLING ANOTHER VESSEL (CHANNEL 16 OR 9) Channel 16 may be used for initial contact (hailing) with another vessel. However, its most important use is for emergency messages. This channel must be monitored at all times except when actually using another channel. It is monitored by the U.S. and Canadian Coast Guards and by other vessels. Use of channel 16 for hailing must be limited to initial contact only. Calling should not exceed 30 seconds, but may be repeated 3 times at 2-minute intervals. In areas of heavy radio traffic, congestion on channel 16 resulting from its use as a hailing channel can be reduced significantly in U.S. waters by using Channel 9 as the initial contact (hailing) channel for non-emergency communications. Also hailing on channel 9, the calling time should not exceed 30 seconds but may be repeated 3 times at 2-minute intervals. Prior to making contact with another vessel, refer to the channel charts in this manual, and select an appropriate channel for communications after initial contact. For example, Channels 68 and 69 of the U.S. VHF Charts are some of the channels available to non-commercial (recreational) boaters. Monitor your desired channel in advance to make sure you will not be interrupting other traffic, and then go back to either channel 16 or 9 for your initial contact. When the hailing channel (16 or 9) is clear, state the name of the other vessel you wish to call and then “this is” followed by the name of your vessel and your Station License (Call Sign). When the other vessel returns your call, immediately request another channel by saying “go to”, the number of the other channel, and “over”. Then switch to the new channel. When the new channel is not busy, call the other vessel. ) switch. After a transmission, say “over”, and release the PTT (Push-To-Talk: When all communication with the other vessel is completed, end the last transHX290 Page 7 Vertex Standard Co., Ltd. FCC ID:K6630453X20 / IC: 511B-30453X20 mission by stating your Call Sign and the word “out”. Note that it is not necessary to state your Call Sign with each transmission, only at the beginning and end of the contact. Remember to return to Channel 16 when not using another channel. 3.5 OPERATING ON CHANNEL 13 Channel 13 is used at docks, bridges and for maneuvering in port. Messages on this channel must concern navigation only, such as meeting and passing in restricted waters. In emergencies and when approaching blind river bends, High power is allowed. Pressing the key will change the power output from Low Power (1 Watt) to High (5 Watts). When you change from this channel then return to it, low power will be automatically selected. 3.6 OPERATING ON CHANNEL 67 When channel 67 is used for navigational bridge-to-bridge traffic between ships, High power may be used temporarily (in the USA band) by pressing the key. When release the PTT ( ) switch, the transceiver will revert to low power. 3.7 SIMPLEX/DUPLEX CHANNEL USE Refer to the section “9. VHF MARINE CHANNEL ASSIGNMENT” for instructions on use of simplex and duplex channels. NOTE All channels are factory-programmed in accordance with FCC, Industry Canada, and International regulations. The mode of operation cannot be altered from simplex to duplex or vice-versa. Simplex (ship to ship) or duplex (marine operator) mode is automatically activated, depending on the channel and whether the USA, Canadian or International operating band is selected. Page 8 HX290 Vertex Standard Co., Ltd. FCC ID:K6630453X20 / IC: 511B-30453X20 MEMO HX290 Page 9 Vertex Standard Co., Ltd. FCC ID:K6630453X20 / IC: 511B-30453X20 4. GETTING STARTED 4.1 RADIO CARE CAUTION Before following the instructions below, insure the battery pack is in place and firmly connected. Care must be taken if the radio was dropped and a close inspection may be needed to insure the radio case and gaskets are in adequate condition. The design of the HX290 allows water to enter between the radio and the battery pack, however waterproof performance is not compromised. After using the HX290 in salt water environment is recommended to clean the radio with fresh water by rinsing the battery and radio (separately) under a sink facet or by dunking in a fresh water. After washing,use a soft cloth to thoroughly dry all parts of the radio and battery. This will keep the radio parts and the battery clean and in top operating condition. 4.2 BELT CLIP INSTALLATION AND REMOVAL To install the Belt Clip: align the Belt Clip to the groove of the Battery pack, then press the Belt Clip downward until it locks in place with a “Click.” To remove the Belt Clip: press the Belt Clip Tab away from the battery pack to unlock the Belt Clip, then slide the Belt Clip upward to remove it. Belt Clip Tab Page 10 HX290 Vertex Standard Co., Ltd. FCC ID:K6630453X20 / IC: 511B-30453X20 4.3 BATTERIES AND CHARGERS If the radio has never been used, or its charge is depleted, it may be charged by connecting the CD-52 Charger Cradle with the PA-44B battery charger, as shown in the illustration. If 12V DC power is available, the optional E-DC-19A DC Cable with 12 V Cigarette Lighter Plug or the optional E-DC-6 DC Cable may be used for charging the battery. The PA-44B, E-DC-19A, and E-DC-6 will charge a completely discharged FNB-110LI battery pack in about 6 hours. The FNB-110LI is a high performance Li-Ion battery providing high capacity in a compact package. CAUTION To avoid risk of explosion and injury, FNB-110LI battery pack should only be removed, charged or recharged in non-hazardous environments. 4.3.1 BATTERY SAFETY Battery packs for your transceiver contain Li-Ion batteries. This type of battery stores a charge powerful enough to be dangerous if misused or abused, especially when removed from the transceiver. Please observe the following precautions: DO NOT SHORT BATTERY PACK TERMINALS: Shorting the terminals that power the transceiver can cause sparks, severe overheating, burns, and battery cell damage. If the short is of sufficient duration, it is possible to melt battery components. Do not place a loose battery pack on or near metal surfaces or objects such as paper clips, keys, tools, etc. When the battery pack is installed on the transceiver, the terminals that transfer current to the transceiver are not exposed. The terminals that are exposed on the battery pack when it is mounted on the transceiver are charging terminals only and do not constitute a hazard. DO NOT INCINERATE: Do not dispose of any battery in a fire or incinerator. The heat of fire may cause battery cells to explode and/or release dangerous gases. Battery Maintenance For safe and proper battery use, please observe the following: Battery packs should be charged only in non-hazardous environments; Use only STANDARD HORIZON-approved batteries; Use only a STANDARD HORIZON approved charger. The use of any other charger may cause permanent damage to the battery. Follow charging instructions provided with the chargers. Keep the battery contacts clean. HX290 Page 11 Vertex Standard Co., Ltd. FCC ID:K6630453X20 / IC: 511B-30453X20 Battery Storage Store the batteries in a cool place to maximize storage life. Since batteries are subject to self-discharge, avoid high storage temperatures that cause large self-discharge rates. After extended storage, a full recharge is recommended. Battery Recycling DO NOT PLACE USED BATTERIES IN YOUR REGULAR TRASH! LI-ION BATTERIES MUST BE COLLECTED, RECYCLED OR DISPOSED OF IN AN ENVIRONMENTALLY SOUND MANNER. The incineration, land filling or mixing of Li-Ion batteries with the municipal solid waste stream is PROHIBITED BY LAW in most areas. Return batteries to an approved Li-Ion battery recycler. This may be where you purchased the battery. Contact your local waste management officials for other information regarding the environmentally sound collection, recycling and disposal of Li-Ion batteries. 4.3.2 BATTERY INSTALLATION/REMOVAL To install the battery pack, hold the transceiver with your left hand, so your palm is over the speaker and your thumb is on the top of the belt clip. Insert the battery pack into the battery compartment on the back of the radio while tilting the Belt Clip outward, then push the bottom side of the battery pack until the battery pack locks with the Battery Pack Latch. To remove the battery, turn the radio off. Slide the Battery Pack Latch on the bottom of the radio, then slide the battery downward and out from the radio while holding the Belt Clip. HAND STRAP INSTALLATION Page 12 HX290 Vertex Standard Co., Ltd. FCC ID:K6630453X20 / IC: 511B-30453X20 4.3.3 BATTERY CHARGING 1. Turn the transceiver off. 2. Insert the DC plug from the PA-44B into the DC jack on the CD-52 side panel, then plug the PA-44B into the AC line outlet. 3. Insert the HX290 (with the battery pack) into the CD-52; the antenna should be at the left side when viewing the charger from the front. 4. If the HX290 is inserted correctly, the LED indicator will glow red. A fully-discharged pack will be charged completely in approximately 6 hours. 5. When charging is completed, the red LED indicator will change to green. Remove the transceiver from the CD-52, and unplug the PA-44B from the AC line outlet. PA-44B CD-52 CAUTION The CD-52 is NOT designed to be waterproof. Do not attempt to charge in water hazardous locations. NOTE The CD-52 is only designed for the charging of the HX290’s battery, and is not suitable for other purposes. The CD-52 may contribute noise to TV and radio reception in the immediate vicinity, so we do not recommend its use adjacent to such device. HX290 Page 13 Vertex Standard Co., Ltd. FCC ID:K6630453X20 / IC: 511B-30453X20 5. CONTROLS AND INDICATORS 5.1 CONTROLS AND SWITCHES NOTE This section defines each control of the transceiver. For detailed operating instructions, refer to section “6. BASIC OPERATION”. Refer to illustrations for the location of the following controls, switches, and connections. NOTE When transmitting, position your mouth about 1/2 to 1 inch (1.2 ~ 2.5 cm) away from the small mic hole. Speak slowly and clearly into the microphone. ANT Jack (Top Panel) The supplied CAT460 flexible antenna is attached here. MIC/SP Jack (Top Panel) The jack accepts the optional MH-73A4B Speaker/Microphone, MH-57A4B Mini Speaker/Microphone, VC-24 VOX Headset, or VC-27 Earpiece/Microphone. When this jack is used, the internal speaker and microphone are disabled. Page 14 HX290 Vertex Standard Co., Ltd. FCC ID:K6630453X20 / IC: 511B-30453X20 POWER Switch/VOLUME Control (VOL) Turns the transceiver on and off as well as adjusts the speakers audio volume. Turn this knob clockwise to turn the radio on and increase the speakers audio volume. Turn fully counter-clockwise to turn the radio off. PTT (Push-To-Talk: ) Switch When pushed activates the transmitter. LCD Display This display shows current operating conditions, as indicated on the page 17. Keypad Key Pressing this key immediately recalls channel 16 from any channel location. Holding down this key recalls channel 9. Pressing this key again reverts to the previous selected working channel. Key Press this key to toggle the transmitter output power between “High” (5 Watts) and “Low” (1 Watt) power. This key does not function on the “Transmission Inhibited” and “Low power only” channels. Secondary use: Hold down this key to lock the keypad (except the keys and PTT ( ) switch) so that they are not accidentally changed. The “ ” icon will appear at the bottom right corner on the display, to indicate that the functions are locked. Hold down this key until the “ ” icon disappears to unlock the radio. Advanced use: When the key is held and the key is pressed, the radio will change the priority channel between the Channel 16, Channel 9, and the Preset Channel. Key Press this key to recall the user preset memory channels (shown as memory channel number “0” - “9” on the display). Press the or key to select the desired preset channel. Press and hold this key for two seconds to memorize the selected channel into the preset memory. HX290 Page 15 Vertex Standard Co., Ltd. FCC ID:K6630453X20 / IC: 511B-30453X20 Key Press the key momentarily to increase the channel one step. Hold the key down to increase the channel continuously. Secondary use: Used to adjust the squelch threshold level up after the key is pressed. Key Press the key momentarily to decrease the channel one step. Hold the key down to decrease the channel continuously. Secondary use: key is pressed. Used to adjust the squelch threshold level down after the Key Press this key to activate the squelch adjusting mode. Press the or key to adjust the squelch threshold level. Press and hold this key for 3 seconds to open the squelch, allowing you to monitor the operating channel. Release the key to resume normal (quiet) monitoring. Key Starts scanning and priority scanning of programmed channels. Secondary use: Press and hold the key for two seconds to activate the Dual Watch feature. Key Press to stop the Scan, Priority Scan, or Dual Watch feature. Secondary use: Press and hold this key to immediately recall the last-used NOAA Weather Channel from any channel location. Recalls the previously- selected workkey is pressed again. ing channel when the Advanced use: When the key is held and the key is pressed, the radio will change the marine band between the USA, International, and Canadian channels. Speaker The internal speaker is located here. Microphone The internal microphone is located here. When transmitting, position your mouth about 1/2 to 1 inch (1.2 ~ 2.5 cm) away from the small mic hole. Speak slowly and clearly into the microphone. Page 16 HX290 Vertex Standard Co., Ltd. FCC ID:K6630453X20 / IC: 511B-30453X20 Battery Pack Lock (Bottom side) Slide the Battery Pack Lock to the “” position for battery removal. 5.2 LCD INDICATORS “ ” Indicator This indicator appears when a signal is being received. “ ” Indicator This indicator appears during transmission. “ ” Indicators This indicator shows the TX output power is “Low” (1 Watt) power. “ ” Indicator ” icon is shown on the When the “ LCD, all keys are disabled except for the PTT ( ), , and keys. “ “ “ “ “ ” Battery Indicator ”: Full battery ”: Lower battery ”: Battery is very low (Blinking)”: Prepare to charge the battery “ ” Indicator This indicator appears when the Dual Watch is activated. “ “ ” Indicator ”: NOAA weather channel is selected. “ ”: “Weather Alert” is received. “PRI” Indicator This indicator shows the channel is in the transceiver’s “Priority Channel”. HX290 SQL Indicator This indicator shows the squelch level. “P” Indicator This indicator shows the channel is in the “Preset Channel”. “U/I/C” Indicator These indicators show the “band” of operation for the particular channel. “U” indicates the USA band; “I” indicates the International band; and “C” indicates the Canadian band. “SCN” Indicator This indicator appears when the Scan is activated. Channel Display The operating channel is shown on the LCD in both the transmission and reception modes. Page 17 Vertex Standard Co., Ltd. FCC ID:K6630453X20 / IC: 511B-30453X20 6. BASIC OPERATION 6.1 PROHIBITED COMMUNICATIONS The FCC prohibits the following communications: False distress or emergency messages: Messages to “any boat” except in emergencies and radio tests; Messages to or from a vessel on land; Transmission while on land; Obscene, indecent, or profane language (potential fine of $10,000). 6.2 INITIAL SETUP 1. Install the battery pack on the transceiver (see section “4.3.2 BATTERY INSTALLATION/REMOVAL”). 2. Install the antenna onto the transceiver; hold the bottom end of the antenna, then screw it onto the mating connector on the transceiver until it is snug. Do not over-tighten. 6.3 RECEPTION 1. Turn the VOL knob clockwise to turn the transceiver on. 2. Press the key to activate the squelch adjusting mode (The “SQL” indicator will blink). Press the key until the “ ” indicator will appear on the display, then press the key again. 3. Turn up the VOL knob until the noise or audio from the speaker is at a comfortable level. 4. Press the key, then press the key until the random noise disappears. This state is known as the “Squelch Threshold”. 5. Press the or key to select the desired channel. Refer to the channel chart on page 33 for available channels. 6. When a signal is received, adjust the VOL knob to the desired listening level. The “ ” indicator in the LCD is displayed indicating that the channel is being used. Page 18 HX290 Vertex Standard Co., Ltd. FCC ID:K6630453X20 / IC: 511B-30453X20 6.4 TRANSMISSION 1. Perform “6.3 RECEPTION” discussion above. 2. Before transmitting, monitor the channel and make sure it is clear. THIS IS AN FCC REQUIREMENT! 3. For communications over short distances, press the key to select the Low power (1 watt: “ ” icon appears). Note: Transmitting on Low power prolongs battery life. Low power should be selected whenever possible. 4. If using Low power is not effective, select High power (5 watts: “ ” icon disappears) by pressing the key. 5. When receiving a signal, wait until the incoming signal stops before transmitting. The transceiver cannot transmit and receive simultaneously. ) switch to transmit. Dur6. Press the PTT (Push-To-Talk: ing transmission, the “ ” indicator will appear on the display. 7. Position your mouth about 1/2 to 1 inch (1.2 ~ 2.5 cm) away from the mic hole. Speak slowly and clearly into the microphone. 8. When the transmission is finished, release the PTT ( ) switch. 6.4.1 TRANSMIT TIME - OUT TIMER (TOT) While the PTT ( ) switch is held down, transmission time is limited to 5 minutes. This prevents prolonged (unintentional) transmissions. About 10 seconds before automatic transmitter shutdown, a warning beep will sound from the speaker. The transceiver automatically switches to the receiving mode, even if the PTT ( ) switch is held down. Before transmitting again, the PTT ( ) switch must first be released, then wait 10 seconds and then pressed again. This Time-Out-Timer (TOT) prevents a continuous transmission that would result from an accidentally stuck PTT ( ) switch. The PTT ( ) switch is ignored for 10 seconds after the transceiver automatically switches to the receiving mode by the TOT feature. HX290 Page 19 Vertex Standard Co., Ltd. FCC ID:K6630453X20 / IC: 511B-30453X20 6.5 USA, CANADIAN, AND INTERNATIONAL CHANNELS 1. To change from US to International or Canadian Marine Channels, hold down the key and press the key. The band will change from USA, to International, and to Canadian with each press. 2. “U” appears on the LCD for the USA band, “I” appears for the International band, and “C” appears for the Canadian band 3. Refer to the marine channel charts in section “9 VHF MARINE CHANNEL ASSIGNMENTS” for allocated channels. 6.6 KEYPAD LOCKING In order to prevent accidental channel change, the HX290’s keypad may be locked out. Hold down the key to lock the keypad (except the keys and PTT ( ) switch) so that they are not accidentally changed. The “ ” icon will appear on the channel number of the display, to indicate that the functions are locked. Hold down the Page 20 key until the “ ” icon disappears to unlock the radio. HX290 Vertex Standard Co., Ltd. FCC ID:K6630453X20 / IC: 511B-30453X20 6.7 NOAA WEATHER CHANNELS In the event of a major storm or other appreciable weather condition requiring vessels at sea (or other bodies of water) to be notified, the NOAA (National Oceanographic and Atmospheric Administration) broadcasts a 1050 Hz tone which the HX290 can detect and alert you of pending storm warnings. The 1050 Hz tone, when detected, will produce a loud beep in the speaker of the HX290, to signal that a Weather Alert Broadcast is being received. 1. To receive a NOAA (National Oceanic and Atmospheric Administration) weather broadcast, press and hold the key. The transceiver changes to the weather channel mode and recalls the last used NOAA weather channel. This mode consists of a preset memory bank containing the NOAA weather channels. or key to change to other weather channels. 2. Press the 3. To exit from the weather channel mode, press and hold the key. The transceiver will revert to the channel you were using prior to switching to the weather channel mode. 6.7.1 NOAA WEATHER ALERT In the event of extreme weather disturbances such as storms and hurricanes, NOAA sends a “weather alert” consisting of a 1050 Hz tone, followed by weather reports on the weather channels. When a “weather alert” is received on a weather channel, the transceiver emits a beep tone and “ ” icon is shown on the display. Press the key to stop the beep tone and listen to the weather reports. NOTE Options for the Weather Alert feature are available, refer to Menu Mode Item “ALt (WX ALERT)” on page 27 for details. 6.7.2 NOAA WEATHER ALERT TESTING In order to test this system, NOAA broadcasts the 1050 Hz tone every Wednesday sometime between 11 AM and 1 PM local time. You may use this opportunity to test your HX290 periodically to confirm that the Weather Alert feature is working, or for training crew members on how to configure the HX290 to receive the NOAA Weather Alerts. HX290 Page 21 Vertex Standard Co., Ltd. FCC ID:K6630453X20 / IC: 511B-30453X20 6.8 PRESET CHANNELS (0 ~ 9): INSTANT ACCESS Ten user assigned channels can be programmed for instant access. Pressing the key activates the user assigned channel bank. 6.8.1 PROGRAMMING 1. Select the desired channel to be saved into the Preset Channel bank using the or key. 2. Press and hold the key until the channel number blinks. The “P” icon and Preset Channel number blink, then release the key. 3. Press the or key to select the desired Preset Chan0 ” ~ “9 9”). If you see the “Underscore” between the current channel nel (“0 number and the Preset Channel number, it means that the Preset Channel currently has no data written on it (i.e. the channel is “free”). 4. Press the key to program the current channel into the Preset Channel bank. 5. Repeat steps 3 and 4 to program the other channel into the Preset Channels, if desired. 6. To delete a Preset Channel, select the Preset Channel number to be deleted using the or key, then press and hold the key until the Preset Channel number is removed from the display, and the Preset Channel number is changed to the next Preset Channel number. 6.8.2 OPERATION 1. Press the key to change the transceiver to the Preset Channel mode. The “P” icon and Preset Channel number will appear on the display. 2. Press the or key to select the desired Preset Chan0” through “9 9”). nels (“0 3. To exit from the Preset Channel mode, press the key. The transceiver will revert to the channel you were on prior to switching to the Preset Channel mode. Page 22 HX290 Vertex Standard Co., Ltd. FCC ID:K6630453X20 / IC: 511B-30453X20 6.9 SCANNING The HX290 will automatically scan channels by two ways of methods of “Memory Scan” and “Priority Scan”. The “Memory Scan” scan channels programmed into Preset Channel Memory and also Scan Channel Memory. The “Priority Scan” channels programmed into Preset Channel Memory and also Scan Channel Memory and the priority channel (Channel 16). When an incoming signal is detected on one of the channels during scan, the transceiver will pause on that channel, allowing you to listen to the incoming transmission. The transceiver will automatically start scanning again after the transmission stops. 6.9.1 SELECTING THE SCAN TYPE 1. Turn the transceiver off by rotating the VOL knob fully counter-clockwise. key, and then turn on the transceiver 2. Hold down the while still holding down the key. SEt 3. “SEt SEt” will appear on the display, indicating the Menu (“Set”) Mode has been activated. 4. Press the key, repeatedly if necessary to select the SC Menu item “SC SC”. PS (Priority Scan)” or or key to select “PS 5. Press the MS (Memory Scan)”. The factory default is “PS PS (Priority “MS Scan)”. 6. After completing your selection, turn the transceiver off and on by rotating the VOL knob. Preset Channel “5” Preset Channel “0” Preset Channel “4” Scan Memory Channel Preset Channel “3” Scan Memory Channel “MEMORY” SCAN HX290 Preset Channel “5” Scan Memory Channel Scan Memory Channel Preset Channel “1” Preset Channel “4” Preset Channel “2” Scan Memory Channel Preset Channel “0” Scan Memory Channel Preset Channel “1” Preset Channel “2” Preset Channel “3” Scan Memory Channel Scan Memory Channel “PRIORITY” SCAN Page 23 Vertex Standard Co., Ltd. FCC ID:K6630453X20 / IC: 511B-30453X20 6.9.2 PROGRAMMING SCAN MEMORY 1. Turn the transceiver off by rotating the VOL knob fully counter-clockwise. 2. Hold down the key, and then turn on the transceiver while still holding down the key. SEt 3. “SEt SEt” will appear on the display, indicating the Menu (“Set”) Mode has been activated. 4. Press the key, repeatedly if necessary to select the SCn Menu item “SCn SCn”. 5. Press the or key to select desired channel to be scanned, then press the key. The “SCN” icon appears on the display, which indicates the channel has been selected to the scan channel. 6. Repeat step 5 for all the desired channels to be programmed into scan memory. 7. To DELETE a channel from the list, select the channel then press the key. The “SCN” icon disappears from the display. 8. When you have completed programming the scan memory, turn the transceiver off and on by rotating the VOL knob. 6.9.3 MEMORY SCANNING (M-SCAN) 1. Adjust the SQL level until background noise is eliminated by pressing the key followed by the or key. 2. To start scanning, press the key. The scan proceed by order of the Scan Memory Channel and the Preset Channel and stops scanning when a transmission is received. Scanning will resume when the incoming signal disappears at the end of the transmission. The “SCN” icon will appear at the left of the channel number on the display during scanning. 3. To stop the scan, press the key briefly. 6.9.4 PRIORITY SCANNING (P-SCAN) 1. Adjust the SQL level until background noise is eliminated by pressing the key followed by the or key. 2. To start scanning, press the key. The scan proceeds from the lowest to the highest programmed channel and the Priority Channel (Channel 16). The “PRI” and “SCN” icons will appear at the left of the channel number on the display during scanning. 3. Even when the transceiver stops and listens to the signal of a programmed Page 24 HX290 Vertex Standard Co., Ltd. FCC ID:K6630453X20 / IC: 511B-30453X20 channel, the transceiver will “dual watch” between this channel and the priority channel. This allows the radio to be able to receive calls on Channel 16 (Priority Channel) even when the radio is receiving on another channel. 4. To stop the scan, press the key briefly. 6.10 DUAL WATCH The Dual Watch feature allows the radio watch the Priority Channel (Channel 16) and one other channel. 1. Select the desired channel using the or key. 2. Press and hold the key for two seconds to activate the Dual Watch feature. A “ ” icon will appear on the upper left of the display when the Dual Watch feature is activated. 3. When a transmission is received on the “Priority Channel (Channel 16)”, the radio receives the “Priority Channel” until the incoming signal disappears. 4. When the radio receives a transmission on the working channel, the radio will dual watch between the working channel and Priority Channel (Channel 16). 5. The Dual Watch feature will resume when the incoming signal disappears at the end of the transmission. 6. To stop the Dual Watch feature and return to normal operation, press the key briefly. HX290 Page 25 Vertex Standard Co., Ltd. FCC ID:K6630453X20 / IC: 511B-30453X20 7. MENU (“SET”) MODE The HX290’s Menu Mode allows a number of the HX290 operating parameters to be custom-configured for your operating requirements. The Menu Mode is easy to activate and set, using the following procedure: 1. Turn the transceiver off by rotating the VOL knob fully counter-clockwise. 2. Hold down the key, and then turn on the transceiver while still holding down the key. SEt 3. “SEt SEt” will appear on the display, indicating the Menu (“Set”) Mode has been activated. 4. Press the key to select the Menu item to be adjusted. 5. Press the or key to enable adjustment of the selected Menu item. 6. Press the key to select the status or value of the Menu item. 7. After completing your adjustment, turn the transceiver off and on by rotating the VOL knob. Page 26 HX290 Vertex Standard Co., Ltd. FCC ID:K6630453X20 / IC: 511B-30453X20 LP (LAMP MODE) Function: Selects the Lamp illumination method for the LCD/ Keypad. Available Values: on / kEY / oFF Default: kEY on: Illuminates the LCD/Keypad continuously. kEY: Illuminates the LCD/Keypad for 5 seconds when any key is pressed. oFF: Turns off the backlight for the LCD and keys. bP (BEEP) Function: Enable/Disable the Keypad beeper. Available Values: HI / Lo / oFF Default: HI SC (SCAN TYPE) Function: Selects the Scan mode. Available Values: PS (Priority Scan) / MS (Memory Scan) Default: PS (Priority Scan) ALt (WX ALERT) Function: Enable/Disable the Weather Alert feature. Available Values: ON / OFF Default: ON SCn (SCAN CHANNEL) Function: Stores the Scan Channel. Refer to section “6.9.2 PROGRAMMING SCAN MEMORY” for programming. HX290 Page 27 Vertex Standard Co., Ltd. FCC ID:K6630453X20 / IC: 511B-30453X20 8. MAINTENANCE 8.1 GENERAL The inherent quality of the solid-state components in STANDARD HORIZON radios will provide many years of continuous use. Take the following precautions to prevent damage to the radio. To prevent corrosion of electrical contacts and keep the water resistance, keep the microphone connected or the jack covered at all times. Never key the transmitter unless an antenna or suitable dummy load is connected to the antenna receptacle. Ensure that the input voltage does not exceed the value specified in your Owner’s Manual. Use only STANDARD HORIZON-approved accessories and replacement parts. 8.2 REPLACEMENT PARTS Occasionally an owner needs a replacement part. These can be ordered from our Parts Department by writing or calling (in USA or Canada), or Standard Horizon/Vertex Standard authorized dealers (outside USA or Canada). Marine Division of Vertex Standard US Headquarters 10900 Walker Street, Cypress, CA 90630, U.S.A. Telephone (714) 827-7600 Commonly requested parts, and their part numbers are listed below. CAT460 Antenna: Q3000176 VOL Knob: RA1193900 MIC/SP Rubber Cap: RA1194200 MIC/SP Plastic Cap: RA108700B CLIP-22 Belt Clip: AAH97X001 Hand Strap: S6000418 Page 28 HX290 Vertex Standard Co., Ltd. FCC ID:K6630453X20 / IC: 511B-30453X20 8.3 TROUBLESHOOTING CHART SYMPTOM The key does not start the scan. PROBABLE CAUSE REMEDY No channels memorized. Enter desired channels into the Preset Channels or Scan Memory Channels. Refer to section 6.8.1 or 6.9.2 of this manual. Squelch is not adjusted. Adjust the squelch to threshold or to the point where noise just disappears. Further adjustment of the squelch control may eliminate incoming signals. Proper operation not followed. HOLD down the the key. Low battery. Charge battery. Refer to section 4.2.3 of this manual. Audio volume level is too low. Turn the VOL knob clockwise. Some keys do not operate. Key Lock is on. Turn Key Lock off. Refer to section 5.1 of this manual ( key). Cannot select keylock function. Proper operation not followed. Hold down the onds. Charging indicator on CD-52 does not illumininate. Defective battery FNB-110LI. Contact your Standard Horizon dealer. Cannot select between USA, INTL, or Canadian bands. Speaker audio is not heard when the key is press and held. HX290 key and press key for 2 sec- Page 29 Vertex Standard Co., Ltd. FCC ID:K6630453X20 / IC: 511B-30453X20 9. VHF MARINE CHANNEL ASSIGNMENTS Tables on the following columns list the VHF Marine Channel assignments for U.S.A. and International use. Below are listed some data about the charts. 1. VTS. Where indicated, these channels are part of the U.S. Coast Guard’s Vessel Traffic System. 2. Alpha channel numbers, that is, channel numbers followed by the letter A (such as Channel 07A) are simplex channels on the U.S.A. or Canadian channel assignments whose counterparts in the International assignments are duplex channels. International channels do not use “alpha” numbers. If you call the Coast Guard on Channel 16, they will sometimes ask you to “go to channel 22 Alpha.” This is a channel assigned to U.S.A, and Canadian Coast Guards for handling distress and other calls. If your radio is set for International operation you will go to Channel 22 instead of 22A, and will not be able to communicate with the Coast Guard. To use Channel 22A, your radio must be set for USA or Canada operation, usually by a U/ I/C (USA/International/Canada) control or combination of controls. Channel 22 (without an “A”) is an International duplex channel for port operations. Some radios indicate an “A” adjacent to the alpha channels on the display; on others “alpha” is not indicated but the proper channel is selected based on the U/I/C setting. 3. Bridge-to-Bridge channels (for example, Channel 13) are for use by bridge operators on inter-coastal waterways and rivers. It is also used by marine vessels in the vicinity of these bridges for navigation and for communicating with the bridge operators. Note that a limit of 1 Watt is specified for these channels. 4. The S/D column on the chart indicates either S (simplex) or D (duplex). Simplex means transmitting and receiving on the same frequency. Only one party at a time can talk, unlike a telephone. Be sure to say “over” and release your microphone push-to-talk switch at the end of each transmission. Duplex operation involves the use of one frequency for transmitting and a separate frequency for receiving. On channels specified as duplex on the charts, correct mode of operation is established automatically by your radio when you select a channel; you cannot change the mode. And you still must release the push-to-talk switch after each transmission in order to listen to the radio. 5. Channels normally used by recreational boaters are those that include the term “non-commercial” in the Channel Use column of the chart. Some of these are shared with other users and some are used only in certain geographic regions. Page 30 HX290 Vertex Standard Co., Ltd. FCC ID:K6630453X20 / IC: 511B-30453X20 6. Marine vessels equipped with VHF radios are required to monitor Channel 16. 7. 156.050 MHz and 156.175 MHz are available for port operations and commercial communications purposes when used only within the U.S. Coast Guard designated Vessel Traffic Services (VTS) area of New Orleans, on the lower Mississippi River from the various pass entrances in the Gulf of Mexico to Devil’s Swamp Light at River Mile 242.4 above head of passes near Baton Rouge. 8. 156.250 MHz is available for port operations communications use only within the U.S. Coast Guard designated VTS radio protection areas of New Orleans and Houston described in Sec. 80.383. 156.250 MHz is available for intership port operations communications used only within the area of Los Angeles and Long Beach harbors, within a 25- nautical mile radius of Point Fermin, California. 9. 156.550 MHz, 156.600 MHz and 156.700 MHz are available in the U.S. Coast Guard designated port areas only for VTS communications and in the Great Lakes available primarily for communications relating to the movement of ships in sectors designated by the St. Lawrence Seaway Development Corporation or the U.S. Coast Guard. The use of these frequencies outside VTS and ship movement sector protected areas is permitted provided they cause no interference to VTS and ship movement communications in their respective designated sectors. 10. Use of 156.875 MHz is limited to communications with pilots regarding the movement and docking of ships. Normal output power must not exceed 1 watt. 5: 156.375 MHz and 156.650 MHz are available primarily for intership navigational communications. These frequencies are available between coast and ship on a secondary basis when used on or in the vicinity of locks or drawbridges. Normal output power must not exceed 1 watt. Maximum output power must not exceed 10 watts for coast stations or 25 watts for ship stations. 11. On the Great Lakes, in addition to bridge-to-bridge communications, 156.650 MHz is available for vessel control purposes in established vessel traffic systems. 156.650 MHz is not available for use in the Mississippi River from South Pass Lighted Whistle Buoy “2” and Southwest Pass entrance Mid-channel Lighted Whistle Buoy to mile 242.4 above Head of Passes near Baton Rouge. Additionally it is not available for use in the Mississippi River-Gulf Outlet, the Mississippi River-Gulf Outlet Canal, and the Inner Harbor Navigational Canal, except to aid the transition from these areas. HX290 Page 31 Vertex Standard Co., Ltd. FCC ID:K6630453X20 / IC: 511B-30453X20 12. Use of 156.375 MHz is available for navigational communications only in the Mississippi River from South Pass Lighted Whistle Buoy “2” and Southwest Pass entrance Mid channel Lighted Whistle Buoy to mile 242.4 above head of Passes near Baton Rouge, and in addition over the full length of the Mississippi River-Gulf Outlet Canal from entrance to its junction with the Inner Harbor Navigation Canal, and over the full length of the Inner Harbor Navigation Canal from its junction with the Mississippi River to its entry to Lake Pontchartrain at the New Seabrook vehicular bridge. 13. Within 120 km (75 miles) of the United States/Canada border, in the area of the Puget Sound and the Strait of Juan de Fuca and its approaches, 157.425 MHz is half of the duplex pair designated as Channel 88. In this area, Channel 88 is available to ship stations for communications with public coast stations only. More than 120 km (75 miles) from the United States/Canada border in the area of the Puget Sound and the Strait of Juan de Fuca, its approaches, the Great Lakes, and the St. Lawrence Seaway, 157.425 MHz is available for intership and commercial communications. Outside Puget Sound area and its approaches and the Great Lakes, 157.425 MHz is also available for communications between commercial fishing vessels and associated aircraft while engaged in commercial fishing activities. 14. When the frequency 156.850 MHz is authorized, it may be used additionally for search and rescue training exercises conducted by state or local governments. 15. The frequency 156.850 MHz is additionally available to coast stations on the Great Lakes for transmission of scheduled Coded Marine Weather Forecasts (MAFOR), Great Lakes Weather Broadcast (LAWEB) and scheduled Notices to Mariners or Bulletins. F3C and J3C emissions are permitted. Coast Stations on the Great Lakes must cease weather broadcasts which cause interference to stations operating on 156.800 MHz until the interference problem is resolved. 16. The frequency 157.100 MHz is authorized for search and rescue training exercises by state or local government in conjunction with U.S. Coast Guard stations. Prior U.S. Coast Guard approval is required. Use must cease immediately on U.S. Coast Guard request. 17. The duplex pair for channel 20 (157.000/161.600 MHz) may be used for ship to coast station communications. 18. Available for assignment to coast stations, the use of which is in accord with an agreed program, for the broadcast of information to ship stations concerning the environment. Page 32 HX290 Vertex Standard Co., Ltd. FCC ID:K6630453X20 / IC: 511B-30453X20 CH 01 01A 02 03 03A 04 04A 05 05A 06 07 07A 08 09 10 11 12 13 14 15 15 16 17 18 18A 19 19A 19A 20 20A 21 21A 22 22A 23 23A 24 25 26 27 28 HX290 VHF MARINE CHANNEL CHART I S/D TX RX CHANNEL USE X D 156.050 160.650 Public Correspondence (Marine Operator) 156.050 Port Operation and Commercial. VTS in selected areas X D 156.100 160.700 Public Correspondence (Marine Operator) X D 156.150 160.750 Public Correspondence (Marine Operator) 156.150 U.S. Government Only, Coast Guard X D 156.200 160.800 Public Correspondence (Marine Operator), Port operation, ship movement 156.200 Pacific coast: Coast Guard, East Coast: Commercial fishing X D 156.250 160.850 Public Correspondence (Marine Operator), Port operation, ship movement 156.250 Port operation. VTS in Seattle X S 156.300 Inter-ship Sefety X D 156.350 160.950 Public Correspondence (Marine Operator), Port operation, ship movement 156.350 Commercial X S 156.400 Commercial (Inter-ship only) X S 156.450 Boater Calling channel, Commercial & Non-commercial (Recreational) X S 156.500 Commercial X S 156.550 Commercial. VTS in selected areas. X S 156.600 Port operation. VTS in selected areas. X S 156.650 Inter-ship Navigation Safety (Bridge-to-bridge) X S 156.700 Port operation. VTS in selected areas. --156.750 Environmental (Receive only) X S 156.750 Commercial, non-commercial, ship movement (1 W) X S 156.800 International Distress, Safety and Calling X S 156.850 State Controlled (1 W) X D 156.900 161.500 Port operation, ship movement 156.900 Commercial X D 156.950 161.550 Port operation, ship movement 156.950 US: Commercial 156.950 Coast Guard X D 157.000 161.600 Canadian Coast Guard Only, International: port operations and shipment 157.000 Port operation X D 157.050 161.650 Port operation, ship movement 157.050 U.S. Government Only, Canadian Coast Guard X D 157.100 161.700 Port operation, ship movement 157.100 US and Canadian Coast Guard Liaison and Maritime Safety Information Broadcasts announced on channel 16 X D 157.150 161.750 Public Correspondence (Marine Operator) 157.150 U.S. Government Only X D 157.200 161.800 Public Correspondence (Marine Operator) X D 157.250 161.850 Public Correspondence (Marine Operator) X D 157.300 161.900 Public Correspondence (Marine Operator) X D 157.350 161.950 Public Correspondence (Marine Operator) X D 157.400 162.000 Public Correspondence (Marine Operator) Page 33 Vertex Standard Co., Ltd. FCC ID:K6630453X20 / IC: 511B-30453X20 CH 60 61 61A 62 62A 63 63A 64 64A 65A 66 66A 67 68 69 70 71 72 73 74 75 76 77 77 78 78A 79 79A 65 Page 34 VHF MARINE CHANNEL CHART I S/D TX RX CHANNEL USE X D 156.025 160.625 Public Correspondence (Marine Operator) X D 156.075 160.675 Public Correspondence (Marine Operator), Port operation, ship movement 156.075 Public Coast: Coast Guard; East Coast: commercial fishing only X D 156.125 160.725 Public Correspondence (Marine Operator), Port operation, ship movement 156.125 Public Coast: Coast Guard; East Coast: commercial fishing only X D 156.175 160.775 Public Correspondence (Marine Operator), Port operation, ship movement 156.175 Port Operation and Commercial. VTS in selected areas. X D 156.225 160.825 Public Correspondence (Marine Operator), Port operation, ship movement 156.225 Public Correspondence (Marine Operator), Port operation, ship movement X D 156.275 160.875 Public Correspondence (Marine Operator), Port operation, ship movement 156.275 Port Operations X D 156.325 160.925 Public Correspondence (Marine Operator), Port operation, ship movement 156.325 Port Operations X S 156.375 US: Commercial. Used for Bridge-to-bridge com munications in lower Mississippi River. Inter-ship only, Canada: Commercial fishing, S&R X S 156.425 Non-commercial (Recreational) X S 156.475 US: Non-commercial (Recreational), Canada: Commercial fishing only, International: Inter-ship, Port operations and Ship movement X S 156.525 Digital selective calling (voice communications not allowed) X S 156.575 US, Canada: Non-commercial (Recreational), International: Port operations and Ship movement X S 156.625 Non-commercial (Inter-ship only) X S 156.675 US: Port Operations, Canada: Commercial fish ing only, International: Inter-ship, Port operations and Ship movement X S 156.725 US: Port Operations, Canada: Commercial fishing only, International: Inter-ship, Port operations and Ship movement X S 156.775 Port Operations (Inter-ship only) (1W) X S 156.825 Port Operations (Inter-ship only) (1W) 156.875 Port Operations (Inter-ship only) (1W) X S 156.875 Port Operations (Inter-ship only) X D 156.925 161.525 Public Correspondence (Marine Operator), Port operation, ship-movement 156.925 Non-commercial (Recreational) X D 156.975 161.575 Port operation and Ship movement 156.975 Commercial HX290 Vertex Standard Co., Ltd. FCC ID:K6630453X20 / IC: 511B-30453X20 CH 80 80A 81 81A 81A 82 82A 83 83 83A 84 85 86 87 87A 88 88A WX01 WX02 WX03 WX04 WX05 WX06 WX07 WX08 WX09 WX10 NOTE: VHF MARINE CHANNEL CHART I S/D TX RX CHANNEL USE X D 157.025 161.625 Port operation, ship movement X X 157.025 Commercial X D 157.075 161.675 Port operation, ship movement 157.075 U.S. Government Only Environmental protection operations. 157.075 Canadian Coast Guard Only X D 157.125 161.725 Public Correspondence (Marine Operator), Port operation, ship movement X X 157.125 U.S. Government Only, Canadian Coast Guard Only D 157.175 161.775 Canadian Coast Guard Only X D 157.175 161.775 Public Correspondence (Marine Operator) X X 157.175 U.S. Government Only, Canadian Coast Guard Only X X X D 157.225 161.825 Public Correspondence (Marine Operator) X X X D 157.275 161.875 Public Correspondence (Marine Operator) X X X D 157.325 161.925 Public Correspondence (Marine Operator) X X S 157.375 Port operation, ship movement 157.375 Public Correspondence (Marine Operator) X X S 157.425 Port operation, ship movement 157.425 Commercial, Inter-ship Only X X X S --162.550 Weather (receive only) X X X S --162.400 Weather (receive only) X X X S --162.475 Weather (receive only) X X X S --162.425 Weather (receive only) X X X S --162.450 Weather (receive only) X X X S --162.500 Weather (receive only) X X X S --162.525 Weather (receive only) X X X S --161.650 Weather (receive only) X X X S --161.775 Weather (receive only) X X X S --163.275 Weather (receive only) Simplex channels, 3A, 21A, 23A, 61A, 64A, 81A, 82A and 83A CANNOT be lawfully used by the general public in U.S.A. waters. HX290 Page 35 Vertex Standard Co., Ltd. FCC ID:K6630453X20 / IC: 511B-30453X20 10. WARRANTY Marine Products Limited Warranty PLEASE NOTE The following “Limited Warranty” is for valid for products that have been purchased in the United States and Canada. For limited Warranty details outside the United States, contact the dealer in your country. STANDARD HORIZON (a division of VERTEX STANDARD) warrants, to the original purchaser only, each new Marine Communications Product (“Product”) manufactured and/or supplied by STANDARD HORIZON against defects in materials and workmanship under normal use and service for a period of time from the date of purchase as follows: Fixed Mount and Portable Transceivers 1 year - if purchased before 01/01/91 3 years - if purchased between 01/01/91 and 01/01/94 3 years Waterproof - if purchased after 01/01/94 Loud hailers 1 year - if purchased before 01/01/91 3 years - if purchased after 01/01/91 Associated Chargers 1 year - if purchased before 01/01/91 3 years - if purchased after 01/01/91 Associated Batteries - 18 months. Note: Batteries will be deemed defective only if storage capacity drops below 80% of rated capacity or if leakage develops. Associated Accessories - 1 year. Includes: Microphones/Handsets, External Speakers, Antennas, Carrying Accessories, Power Supplies, and Signaling Boards. To receive warranty service, the purchaser must deliver the Product, transportation and insurance prepaid, to STANDARD HORIZON (a division of VERTEX STANDARD). Include proof of purchase indicating model. serial number, and date of purchase. STANDARD HORIZON will return the Product to the purchaser freight prepaid. Products purchased prior to January 1, 1991 will bear the STANDARD HORIZON warranty terms in effect prior to that date. In the event of a defect, malfunction or failure of the Product during the warranty period, STANDARD HORIZON’s liability for any breach of contract or any breach of express or implied warranties in connection with the sale of Products shall be limited solely to repair or replacement, at its option, of the Product or part(s) therein which, upon examination by STANDARD HORIZON, Page 36 HX290 Vertex Standard Co., Ltd. FCC ID:K6630453X20 / IC: 511B-30453X20 appear to be defective or not up to factory specifications. STANDARD HORIZON may, at its option, repair or replace parts or subassemblies with new or reconditioned parts and subassemblies. Parts thus repaired or replaced are warranted for the balance of the original applicable warranty. STANDARD HORIZON will not warrant installation, maintenance or service of the Products. In all instances, STANDARD HORIZON’s liability for damages shall not exceed the purchase price of the defective Product. This warranty only extends to Products sold within the 50 States of the United States of America and the District of Columbia. STANDARD HORIZON will pay all labor to repair the product and replacement parts charges incurred in providing the warranty service except where purchaser abuse or other qualifying exceptions exist. The purchaser must pay any transportation expenses incurred in returning the Product to STANDARD HORIZON for service. This limited warranty does not extend to any Product which has been subjected to misuse, neglect, accident, incorrect wiring by anyone other than STANDARD HORIZON, improper installation, or subjected to use in violation of instructions furnished by STANDARD HORIZON, nor does this warranty extend to Products on which the serial number has been removed, defaced, or changed. STANDARD HORIZON cannot be responsible in any way for ancillary equipment not furnished by STANDARD HORIZON which is attached to or used in connection with STANDARD HORIZON’s Products, or for the operation of the Product with any ancillary equipment, and all such equipment is expressly excluded from this warranty. STANDARD HORIZON disclaims liability for range, coverage, or operation of the Product and ancillary equipment as a whole under this warranty. STANDARD HORIZON reserves the right to make changes or improvements in Products, during subsequent production, without incurring the obligation to install such changes or improvements on previously manufactured Products. The implied warranties which the law imposes on the sale of this Product are expressly LIMITED, in duration, to the time period specified above. STANDARD HORIZON shall not be liable under any circumstances for consequential damages resulting from the use and operation of this Product, or from the breach of this LIMITED WARRANTY, any implied warranties, or any contract with STANDARD HORIZON. IN CONNECTION WITH THE SALE OF ITS PRODUCTS, STANDARD HORIZON MAKES NO WARRANTIES, EXPRESS OR IMPLIED AS TO THE MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE, EXCEPT AS EXPRESSLY SET FORTH HEREIN. HX290 Page 37 Vertex Standard Co., Ltd. FCC ID:K6630453X20 / IC: 511B-30453X20 Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitation on how long an implied warranty lasts, so the above limitations or exclusions may not apply. This warranty gives specific legal rights, and there may be other rights which may vary from state to state. ONLY PRODUCTS SOLD ON OR AFTER JANUARY 1, 1991 ARE COVERED UNDER THE TERMS OF THIS LIMITED WARRANTY. ON-LINE WARRANTY REGISTRATION THANK YOU for buying STANDARD HORIZON (a division of Vertex Standard) products! We are confident your new radio will serve your needs for many years! Please visit www.standardhorizon.com to register the HX290 Marine VHF. It should be noted that visiting the Web site from time to time may be beneficial to you, as new products are released they will appear on the STANDARD HORIZON Web site. Product Support Inquiries If you have any questions or comments regarding the use of the HX290, you can visit the STANDARD HORIZON Web site to send an E-mail or contact the Product Support team at (714) 827-7600 ext 6300 M-F 7:005:00PST. In addition to the warranty, STANDARD HORIZON includes a lifetime “flat rate” program to provide service after the warranty period has expired. If you wish to obtain the flat rate price for out-of-warranty repair, you must include the information on the Owner’s Record with the unit when you return it to your Dealer or to STANDARD HORIZON. Lifetime Flat Rate Service Program: For the original Owner only, for the lifetime of the unit, STANDARD HORIZON will repair the unit to original specifications. Note: The flat rate amount is payable by the Owner only if STANDARD HORIZON or the STANDARD HORIZON Dealer determines that a repair is needed. After the repair, a 90-day warranty will be in effect from the date of return of the unit to the .Owner. This service program is not available for equipment which has failed as a result of neglect, accident, breakage, misuse, improper installation or modification, or water damage (depending on the product). Page 38 HX290 Vertex Standard Co., Ltd. FCC ID:K6630453X20 / IC: 511B-30453X20 11. INSTALLATION OF OPTION 11.1 FBA-42 ALKALINE BATTERY CASE FBA-42 is a battery case that holds six AA size Alkaline batteries and is used with the HX290 transceiver. When the FBA-42 is installed into the HX290 the radio can withstand immersion in water up to 1.5 m (about 5Ft) for 30 minutes. 1. On the FBA-42, remove the battery case cover. When it is hard to remove the battery case cover, put a coin to the edge of the battery compartment ( ) then pry open the battery case cover. 2. Slide the six AA size Alkaline batteries into the FBA-42 Battery Case with the Negative (–) side of the batteries touching the spring connections inside the FBA-42 Battery Case. 3. Attach the battery cover to the FBA-42 Battery Case while being careful so that o-ring is not twisted. 4. Insert the FBA-42 Battery Case into the battery compartment on the back of the HX290 transceiver while tilting the Belt Clip outward, then push the bottom side of the FBA-42 Battery Case until the Battery Case locks with the Battery Pack Latch. HX290 Page 39 Vertex Standard Co., Ltd. FCC ID:K6630453X20 / IC: 511B-30453X20 12. SPECIFICATIONS Performance specifications are nominal, unless otherwise indicated, and are subject to change without notice. 12.1 GENERAL Frequency Ranges: Channel Spacing: Frequency Stability: Emission Type: Antenna Impedance: Supply Voltage: Current Consumption: Operating Temperature: Case Size (W x H x D): Weight (Approx.): TX: 156.025 MHz - 157.425 MHz RX: 156.050 MHz - 163.275 MHz 25 kHz ±5 ppm (–4 °F to +140 °F [–20 °C to +60 °C]) 16K0G3E 50 7.4V DC, Negative Ground (Battery Terminal) 320 mA (Receive, Typical at AF MAX.) 50 mA (Standby) 1.6 A / 0.7 A (TX: 5 W / 1W) –4 °F to +140 °F (–20 °C to +60 °C) 2.24” x 5.24” x 1.73” (57 x 133 x 44 mm) (w/o knob & antenna) 10.9 oz (310 g) (w/FNB-110LI, Belt Clip, & Antenna) 12.2 TRANSMITTER RF Power Output: Modulation Type: Maximum Deviation: Spurious Emission: Microphone Impedance: 5 W / 1 W (@7.4 V ) Variable Reactance ±5 kHz –75 dBc typical 2 k 12.3 RECEIVER Circuit Type: Intermediate Frequencies: Adjacent Channel Selectivity: Intermodulation: Hum & Noise Ratio: Sensitivity: Selectivity: AF Output (Internal SP): Double-Conversion Superheterodyne 1st: 21.7 MHz, 2nd: 450 kHz 70 dB typical 68 dB typical 40 dB typical 0.25 μV for 12 dB SINAD 25 kHz (–70 dB) 700 mW @16 for 10 % THD (@7.4 V) Measured in accordance with TIA/EIA-603. Page 40 HX290 Vertex Standard Co., Ltd. FCC ID:K6630453X20 / IC: 511B-30453X20 13. FCC & CANADA RADIO LICENSE INFORMATION Standard Horizon radios comply with the Federal Communication Commission (FCC) and Industry-Canada requirements that regulate the Maritime Radio Service. 13.1 MARITIME STATION LICENSE An FCC ship station license is no longer required for any vessel traveling in U.S. waters which uses a VHF marine radio, RADAR or EPIRB, and which is not required to carry radio equipment. However, any vessel required to carry a marine radio on an international voyage, carrying a HF single side band radiotelephone or marine satellite terminal. FCC license forms, including applications for ship (605) and land station licenses can be downloaded via the Internet at www.fcc.gov/Forms/Form605/605.html. To obtain a form from the FCC, call (888) 225-5322. 13.2 MARINE RADIO CALL SIGN Currently the FCC does not require recreational boaters to have a Ship Radio Station License. The USCG recommends the boats registration number and the state to be used. 13.3 CANADIAN SHIP STATION LICENSING You may need a license when traveling in Canada. If you do need a license contact their nearest field office or regional office or write: Industry Canada Radio Regulatory Branch Attn: DOSP 300 Slater Street Ottawa, Ontario Canada, KIA 0C8 13.4 FCC / INDUSTRY CANADA INFORMATION The following data pertaining to the transceiver is necessary to fill out the license application. FCC Type Accepted: ........................................................................... Part 80 Output Power with FNB-V105LI: ................................... 1.0/5.0 W (Low/High) Emission: ......................................................................................... 16K0G3E Frequency Range: .................................................... 156.025 to 163.275MHz FCC Type Number: .................................................................. K6630453X20 Industry Canada Type Approval: ........................................... 511B-30453X20 HX290 Page 41 Vertex Standard Co., Ltd. FCC ID:K6630453X20 / IC: 511B-30453X20 14. FCC NOTICE Unauthorized changes or modifications to this equipment may void compliance with FCC Rules. Any change or modification must be approved in writing by STANDARD HORIZON, a Marine Division of VERTEX STANDARD. NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced marine electronics technician for help. Page 42 HX290 Vertex Standard Co., Ltd. FCC ID:K6630453X20 / IC: 511B-30453X20 This device complies with part 15 of the FCC rules. Operation is subject to the condition that this device does not cause harmful interference. Part 15.21: Changes or modifications to this device not expressly approved by Vertex Standard could void the User’s authorization to operate this device. HX290 Page 43 Vertex Standard Co., Ltd. FCC ID:K6630453X20 / IC: 511B-30453X20 Marine Division of VERTEX STANDARD US Headquarters 10900 Walker Street, Cypress, CA 90630, U.S.A. Page 44 Copyright 2011 VERTEX STANDARD CO., LTD. All rights reserved. No portion of this manual may be reproduced without the permission of VERTEX STANDARD CO., LTD. Printed in China HX290 Vertex Standard Co., Ltd.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No XMP Toolkit : 3.1-701 Producer : Acrobat Distiller 9.4.0 (Windows) Creator Tool : PageMaker 7.0J Modify Date : 2011:01:11 11:38:53+09:00 Create Date : 2010:12:03 08:02:38+09:00 Metadata Date : 2011:01:11 11:38:53+09:00 Format : application/pdf Title : HX290.pmd Creator : yohtaki Document ID : uuid:7fb4cee8-333b-4bde-9729-e6c2cddc80c2 Instance ID : uuid:e5c52d58-4e92-4487-a06d-465bacd2b4ae Has XFA : No Page Count : 44 Author : yohtakiEXIF Metadata provided by EXIF.tools