Yaesu Musen 30593X3D MOBILE MARINE TRANSCEIVER User Manual GX6000 Owner s Manual
Yaesu Musen Co., Ltd. MOBILE MARINE TRANSCEIVER GX6000 Owner s Manual
Contents
OM User Manual 10
18.9 18.9.1 NMEA 0183 IN/OUT Data Speed This menu is used to setup the NMEA 0183 baud rate of the GPS input (Blue and Green wires) and DSC output (Gray and Brown wires). The default setting is 4800 bps. When 38400 bps is selected the AIS sentences (VDM) and DSC sentences (DSC & DSE) both are output on the Gray and Brown wires after a DSC distress, position request or AIS transmission is received. 1. ] “SETUP” “GPS SETUP” “NMEA 0183 IN/OUT” 2. Rotate the DIAL/ENT knob to select “DATA SPEED”, then press the [SELECT] soft key. 3. Rotate the DIAL/ENT knob to select the desired speed from “4800bps” and “38400bps”. 4. Press the [ENTER] soft key to save the new setting. 5. Press the CLEAR key to return to radio operation. 18.9.2 Output Sentences This selection is used to setup the NMEA output sentences of the GX6000. By default, all the NMEA sentences are turned “ON”. 1. ] “SETUP” “GPS SETUP” “NMEA 0183 IN/OUT” 2. Rotate the DIAL/ENT knob to select “OUTPUT SENTENCES”, then press the [SELECT] soft key. 3. Rotate the DIAL/ENT knob to select the desired sentence type, then press the [SELECT] soft key. Page 124 GX6000 4. 5. 6. 7. Rotate the DIAL/ENT knob to select “ON” or “OFF”. Press the [ENTER] soft key to save the new setting. Repeat steps 3 through 5 to set the other sentences. Press the CLEAR key to return to radio operation. NOTE • Data output will be performed based on the data acquisition order of priority configured from “ORDER OF PRIORITY”. Refer to section “18.1 ORDER OF PRIORITY” for details. • While “UNIT POWER” of “OPTION GPS UNIT” is set to OFF, NMEA sentences will not be output. (OPTION GPS reception data will be output as is.) • The output interval of each NMEA sentence depends on the output timing on the input device. However, sentences which include POS data will be output at intervals of two seconds or less. • When all sentences are set to be output, depending on the baud rate, not all sentences can be output at intervals of one second or less. GSA and GSV sentences will be output at intervals of around five seconds. 18.10 Position Data Output Select the connection device to be used when outputting position data. 1. ] “SETUP” “GPS SETUP” “OPTION GPS UNIT” 2. Rotate the DIAL/ENT knob to select “POS DATA OUTPUT”, then press the [SELECT] soft key. 3. Rotate the DIAL/ENT knob to select “NMEA 2000” or “NMEA 0183”, then press the [SELECT] soft key. 4. Rotate the DIAL/ENT knob to select “OFF” or “ON”. 5. Press the [ENTER] soft key to store the new setting. 6. Press the CLEAR key to return to radio operation. GX6000 Page 125 18.11 OPTION GPS UNIT Change the optional GPS Antenna (SCU-31) setting. 18.11.1 Unit Power When you use the SCU-31, set this selection to “ON”. The default setting is “OFF”. 1. ] “SETUP” “GPS SETUP” “OPTION GPS UNIT” 2. Rotate the DIAL/ENT knob to select “UNIT POWER”, then press the [SELECT] soft key. 3. Rotate the DIAL/ENT knob to select “OFF” or “ON”. 4. Press the [ENTER] soft key to store the new setting. 5. Press the CLEAR key to return to radio operation. 18.11.2 Pinning This selection is used to enable or disable position updates when the vessel is not underway. The default setting is “ON”. 1. ] “SETUP” “GPS SETUP” “OPTION GPS UNIT” 2. Rotate the DIAL/ENT knob to select “PINNING”, then press the [SELECT] soft key. 3. Rotate the DIAL/ENT knob to select “OFF” or “ON”. ON: When pinning is turned on, the GX6000 will not update its position unless the ship’s speed over approximately 0.4 knot. OFF: When the vessel is underway or stopped, the GX6000 continuously updates its position. This improves accuracy of the position fix. 4. Press the [ENTER] soft key to save the new setting. 5. Press the CLEAR key to return to radio operation. Page 126 GX6000 18.11.3 Differential GPS This selection enables or disables differential GPS function by SBAS (Satellite Based Augmentation System) such as WAAS, EGNOS and MSAS. In some areas (Australia for example), the GPS reception can have problems on enabling the SBAS. The default setting is “OFF”. 1. ] “SETUP” “GPS SETUP” “OPTION GPS UNIT” 2. Rotate the DIAL/ENT knob to select “DIFFERENTIAL GPS”, then press the [SELECT] soft key. 3. Rotate the DIAL/ENT knob to select “OFF” or “ON”. 4. Press the [ENTER] soft key to store the new setting. 5. Press the CLEAR key to return to radio operation. 18.11.4 Logger Interval 1. ] “SETUP” “GPS SETUP” “OPTION GPS UNIT” 2. Rotate the DIAL/ENT knob to select “LOGGER INTERVAL”, then press the [SELECT] soft key. 3. Rotate the DIAL/ENT knob to select the desired time and press the [ENTER] soft key. Note: Log time for each logger interval setting 15 sec: Aprox. 25 hours 30 sec: Aprox. 50 hours 1 min: Aprox. 100 hours 2 min: Aprox. 200 hours 5 min: Aprox. 500 hours 4. Press the CLEAR key to return to radio operation. GX6000 Page 127 18.11.5 Log Erase 1. ] “SETUP” “GPS SETUP” “OPTION GPS UNIT” 2. Rotate the DIAL/ENT knob to select “LOG ERASE”, then press the [SELECT] soft key. 3. Press the [YES] soft key. (To cancel, press the [NO] soft key.) 4. Press the [OK] soft key. 5. Press the CLEAR key to return to radio operation. 18.12 SUMMARY OF THE GPS SETUP Item Description ORDER OF PRIORITY Sets the order of priority of the connection devices when obtaining position information COMPASS DIRECTION Selects the compass direction to be displayed LOCATION FORMAT Selects the coordinate system to be displayed TIME OFFSET Sets the offset time from the UTC (available only when “LOCAL” is selected in the item “TIME AREA”) TIME AREA Selects the time location to be displayed, from UTC or local TIME FORMAT Selects the time format to be displayed, 12-hour or 24-hour (fixed to “24H” when “UTC” is selected in the item “TIME AREA”) UNITS OF MEASURE Selects the unit if measure when displaying speed, distance, and altitude Default Value 122 COURSE-UP 122 ddd°mm.mmmm 122 00:00 123 UTC 123 24hour 123 SPEED: kts (knots) DISTANCE: nm (nautical mile) ALTITUDE: ft (feet) MAGNETIC VARIATION Enables/disables the magnetic OFF variation function NMEA 0183 IN/OUT DATA SPEED Page 128 Sets the NMEA 0183 data speed Page NMEA-0183 4800bps 123 123 124 GX6000 Item Description Default Value OUTPUT SENTENCES Enables/disables NMEA sentences GLL: ON GGA: ON GSA: ON GSV: ON RMC: ON DSC/DSE: ON POS DATA OUTPUT Selects the connection device NMEA 2000: OFF when outputting position data NMEA-0183: OFF OPTION GPS UNIT UNIT POWER Enables/disables the OPTION GPS UNIT PINNING Turns on or off GPS position updates for vessel not underway DIFFERENTIAL GPS Turns on or off of use of SBAS LOGGER INTERVAL Selects the interval time of logging LOG ERASE Erases the log data GX6000 Page 124 125 OFF 126 OFF 126 ON 2 min 127 127 128 − Page 129 19 SSM-70H (RAM4) REMOTE MIC OPERATION When a remote microphone is connected to the GX6000, all VHF, DSC, setup menus, AIS, Navigation, GM (Group Monitor) functions and PA/Fog modes can be remotely operated. The SSM-70H’s operation is same as GX6000 except the receiver audio volume setting and squelch level setting. The reason for the same operation is to make the operation of the radio and SSM-70H mic easy. For specific operation of the SSM-70H mic review sections in the radio manual. The SSM-70H is supplied with 23 feet (7 m) of routing cable and can be extended up to 70 feet (21 m) using three 23 feet (7 m) extension cables model CT-100. The Intercom feature can be used between the SSM-70H and the GX6000. In addition, speaker wires are supplied at the panel mount of the routing cable for external speakers to be connected in noisy environments. 19.1 REMOTE MIC CONTROLS Power/VOL knob Press and hold this knob to turn the transceiver and the remote mic on or off. Rotate this knob to adjust the internal speaker volume. Page 130 GX6000 DIAL/ENT knob While the normal screen is displayed, rotate the DIAL/ENT knob to select your desired channel. While the MENU screen is displayed, rotate the knob to select your desired menu item. Secondary use Press this knob to enter a selection in the MENU. SQL key (Squelch control) Press this key to activate the squelch adjusting mode. Press the CH▲ or CH▼ key to adjust the squelch threshold level. PTT (Push-To-Talk) switch Push this switch to enable the transmitter. CLEAR/ key Press this key to cancel a menu selection. Press and hold this key to activate the key lock function. Press and hold this key again to deactivate the key lock function. Microphone The internal microphone transmits your voice reducing background noise using Clear Voice Noise Reduction Technology. Note: Position your mouth about 1/2” (1.5 cm) away from the microphone hole and speak in a normal voice. ◄/► key Press these keys to switch the function of soft keys Secondary use While the MENU screen is displayed, press the key to slide the on-screen menu to the right/left side. MENU key Press this key to access the MENU. CH▼/CH▲ key These keys are used to change the operating channel. Press the key momentarily, the channel increases/decreases one step. Holding the key, the channel increases/decreases continuously. Secondary use While the MENU screen is displayed, press the key to slide the on-screen menu upward/downward. When in the PA or Fog mode, press the key to change the channel. Display Full dot matrix display, 222 by 162 pixels. Soft keys These three programmable keys can be customized through the setup menu mode. When pressing one of these keys briefly, the key functions will appear at the bottom of the display. Refer to section “19.2 RAM4 SOFT KEY ASSIGNMENT” for details. Strobe Light When the [STROBE] soft key is pressed, the internationally-recognized GX6000 Page 131 Morse Code “S.O.S” message will light and flash repeatedly. From MENU → SETUP → CONFIGURATION → STROBE LED, you can select one option from “CONTINUOUS”, “SOS”, “BLINK 1”, “BLINK 2” and “BLINK 3”. 16/S key Pressing this key immediately recalls channel 16 from any channel location. Holding down this key recalls the SUB channel (The default setting is channel 9). Pressing this key again reverts to the previous selected working channel. Speaker The internal speaker is located here. DATA jack Use the micro USB type B jack for SSM-70H (RAM4) firmware updates. Note: When the DATA jack is securely covered with rubber cap, the SSM70H meets the waterproofing performance. DISTRESS key This key is used to send a DSC distress call. Refer to section “10 DIGITAL SELECTIVE CALLING (DSC)”. 19.2 RAM4 SOFT KEY ASSIGNMENT From this menu, you can assign desired functions to each RAM4 soft key from numbers 01 to 12. You can also set how long the soft key icon will be displayed after the corresponding soft key is pressed. The keys maybe setup to control the following functions: DISPLAY FUNCTION NONE TX HI/LO WX/CH SCAN DUAL WATCH MARK POSITION SCAN MEMORY PRESET MAN OVER BOARD NOISE CANCEL CH NAME STROBE SCRAMBLER COMPASS WAYPOINT FOG HORN INTERCOM − GPS LOGGER AIS DISPLAY HORN BUTTON PUBLIC ADDRESS RX RECORD RX SENSE Page 132 Selects transmit power. Switches channels between weather and marine. Turns on or off scanning function. Starts and stops dual watch scan. Marks the current position for a “Waypoint”. Add or remove channels from memory channel scan. Programs or deletes the preset memory channel. Marks the position where a person falls overboard. Enables the noise canceling settings display. Edit channel names. Turns on or off the strobe light LED. Configures the secret communication settings. Enables the “Compass” display. Enables the “Waypoint” or “Route” navigation display. Select FOG HORN mode. Activates intercom between radio and RAM4 mic (optional RAM4 required). Starts and stops logging position data. Shows the “AIS” display. Activates the Fog Horn function. Activates the PA function. Records received voices. Toggles between LOCAL and DISTANCE. SOFT KEY NUMBERS ASSIGNED AS DEFAULT (See the next page.) − 02 01 05 06 09 04 10 03 12 07 11 GX6000 DISPLAY SOFT KEY NUMBERS ASSIGNED AS DEFAULT FUNCTION PLAY (See the next page.) Plays recorded voices. 08 NOTE You can assign functions to soft keys on each of the transceiver and the optional SSM-70H (RAM4) remote mic. 19.2.1 Key Assignment Configure all settings on the SSM-70H (RAM4) remote mic for which you want to assign functions to soft keys. 1. ] “SETUP” “CONFIGURATION” “SOFT KEY” 2. Rotate the DIAL/ENT knob to select “KEY ASSIGNMENT”, then press the [SELECT] soft key. 3. Rotate the DIAL/ENT knob to select the key number to be programmed, and press the [SELECT] soft key. 4. Rotate the DIAL/ENT knob to select a new function to be assigned, and press the [ENTER] soft key. Available functions are listed below. By selecting “NONE” the soft key assignment is removed. 5. Repeat steps 3 and 4 to program other soft keys. Up to 24 functions can be assigned. The VHF radio's functions can be assigned to the maximum of 12 soft keys. Pressing the ►/◄ key each time shows three different soft keys. 01 02 03 04 05 06 07 08 09 10 11 12 (The illustration above is the default setting.) 6. Press the CLEAR/ GX6000 key to return to radio operation. Page 133 20 CONNECTING A USB DATA TERMINAL TO THE PC The GX6000 settings can be programmed using the USB terminal and PC Programming Software. You can also download the log data from the radio by using the PC Programming Software which may be downloaded from the Standard Horizon website. The PC Programming Software is compatible with Windows®. To connect a PC, use the supplied USB cable through the DATA jack of the GX6000. DATA jack supplied USB cable CAUTION The DATA jack is NOT designed to be waterproof when the cover is opened. Connect the radio and PC in a dry location. If you have further questions, please feel free to contact Product Support at: Phone: (800) 767-2450 Email: marinetech@yaesu.com 21 MAINTENANCE The inherent quality of the solid-state components used in this transceiver will provide many years of continuous use. Taking the following precautions will prevent damage to the transceiver. • Never key the microphone unless an antenna or suitable dummy load is connected to the transceiver. • Ensure that the supply voltage to the transceiver does not exceed 16 VDC or fall below 11 VDC. • Use only STANDARD HORIZON approved accessories and replacement parts. In the unlikely event of serious problems, please contact your Dealer or our repair facility. Address and phone numbers for this facility, as well as warranty information, are contained in section “23 WARRANTY”. GX6000 Page 134 21.1 REPLACEMENT PARTS Occasionally an owner needs a replacement mounting bracket or knob. These can be ordered from our Parts Department by emailing yaesuparts@yaesu.com or calling: Marine Division of YAESU U.S.A. 6125 Phyllis Drive, Cypress, California 90630 Telephone (714) 827-7600 Commonly requested parts, and their part numbers are listed below. • Power Cord: T9027407 • VOL and SQL Knob: RA6057800 • DIAL/ENT Knob: RA6057700 • Mounting Bracket: RA6060600 • Mounting Bracket Knob: RA0978600 • Microphone Hanger: RA0458800 • RAM4 Mic Routing Cable Assembly: S8101512 • USB Cable: T9101648 21.2 FACTORY SERVICE In the unlikely event that the radio fails to perform or needs servicing, please contact the following: Standard Horizon Attention Marine Repair Department 6125 Phyllis Drive, Cypress, California 90630, U.S.A. Telephone (800) 366-4566 For repairs in Canada Westcom Marine 488 East 62nd Avenue Vancouver BC V5X2G1 Telephone (604) 327-6280 An “RA” (Return Authorization) number is not necessary to send a product in for service. Include a brief note describing the problem along with your name, return address, phone number, and proof of purchase. GX6000 Page 135 21.3 TROUBLESHOOTING CHART SYMPTOM PROBABLE CAUSE Transceiver fails to power up. No DC voltage to the transceiver, or blown fuse. Transceiver blows fuse when connected to power supply. Reversed power wires. Popping or whining noise from the speaker while engine runs. Sound is not emitted from the internal or external speaker. Sound is not emitted from the PA speaker. Receiving station reports low transmit power, even with transceiver set to HI power. “HI BATTERY” or “ L O B AT T E RY ” message appears when the power is turned on. Your position is not displayed. Engine noise. Accessory cable. Accessory cable. Antenna. Check the connections of the accessory cable. PA speaker cable (RED/SHIELD) shorted together. Have the antenna checked or test the transceiver with another antenna. If the problem persists, contact your Dealer for servicing. The power supply voltage is too high or too low. Confirm that the connected power supply voltage is between 11 volts and 16.5 volts DC. SCU-31 cable. Accessory cable. Check the SCU-31 cable connection. Check the accessory cable connection. Some GPS use the battery ground for NMEA connection. Check the output signal format of the GPS navigation receiver. This radio requires NMEA 0183 and NMEA 2000 format with GLL, RMB, or RMC sentence as an output signal. If the GPS has a baud rate setting make sure to select 4800 and parity to NONE. Setting of the GPS chart plotter. Page 136 REMEDY a. Check the 12VDC battery connections and the fuse. b. The key needs to be pressed and held to turn the radio on. Check the power cable for DC voltage, or replace the fuse (7A). Make sure the red wire is connected to the positive (+) battery post, and the black wire is connected to the negative (–) battery post. If the fuse still blows, contact your Dealer. Re-route the DC power cables away from the engine. Add noise suppressor on power cable. Change to resistive spark plug wires and/or add an alternator whine filter. Check the connections of the accessory cable. External speaker cable (WHITE/ SHIELD) shorted together. GX6000 22 CHANNEL ASSIGNMENTS Tables on the following columns list the VHF Marine Channel assignments for U.S.A. and International use. Below are listed some data about the charts. 1. VTS. Where indicated, these channels are part of the U.S. Coast Guard’s Vessel Traffic System. 2. Alpha channel numbers, that is, channel numbers followed by the letter A (such as Channel 07A) are simplex channels on the U.S.A. or Canadian channel assignments whose counterparts in the International assignments are duplex channels. International channels do not use “alpha” numbers. If you call the Coast Guard on Channel 16, they will sometimes ask you to “go to channel 22 Alpha”. This is a channel assigned to U.S.A, and Canadian Coast Guards for handling distress and other calls. If your radio is set for International operation you will go to Channel 22 instead of 22A, and will not be able to communicate with the Coast Guard. To use Channel 22A, your radio must be set for USA or Canada operation, usually by a U/I/C (USA/International/Canada) control or combination of controls. Channel 22 (without an “A”) is an International duplex channel for port operations. Some radios indicate an “A” adjacent to the alpha channels on the display; on others “alpha” is not indicated but the proper channel is selected based on the U/I/C setting. 3. Bridge-to-Bridge channels (for example, Channel 13) are for use by bridge operators on inter-coastal waterways and rivers. It is also used by marine vessels in the vicinity of these bridges for navigation and for communicating with the bridge operators. Note that a limit of 1 Watt is specified for these channels. 4. The S/D column on the chart indicates either S (simplex) or D (duplex). Simplex means transmitting and receiving on the same frequency. Only one party at a time can talk, unlike a telephone. Be sure to say “over” and release your microphone push-to-talk switch at the end of each transmission. Duplex operation involves the use of one frequency for transmitting and a separate frequency for receiving. On channels specified as duplex on the charts, correct mode of operation is established automatically by your radio when you select a channel; you cannot change the mode. And you still must release the push-to-talk switch after each transmission in order to listen to the radio. 5. Channels normally used by recreational boaters are those that include the term “non-commercial” in the Channel Use column of the chart. Some of these are shared with other users and some are used only in certain geographic regions. GX6000 Page 137 6. Marine vessels equipped with VHF radios are required to monitor Channel 16. 7. 156.050 MHz and 156.175 MHz are available for port operations and commercial communications purposes when used only within the U.S. Coast Guard designated Vessel Traffic Services (VTS) area of New Orleans, on the lower Mississippi River from the various pass entrances in the Gulf of Mexico to Devil’s Swamp Light at River Mile 242.4 above head of passes near Baton Rouge. 8. 156.250 MHz is available for port operations communications use only within the U.S. Coast Guard designated VTS radio protection areas of New Orleans and Houston described in Sec. 80.383. 156.250 MHz is available for intership port operations communications used only within the area of Los Angeles and Long Beach harbors, within a 25- nautical mile radius of Point Fermin, California. 9. 156.550 MHz, 156.600 MHz and 156.700 MHz are available in the U.S. Coast Guard designated port areas only for VTS communications and in the Great Lakes available primarily for communications relating to the movement of ships in sectors designated by the St. Lawrence Seaway Development Corporation or the U.S. Coast Guard. The use of these frequencies outside VTS and ship movement sector protected areas is permitted provided they cause no interference to VTS and ship movement communications in their respective designated sectors. 10. Use of 156.875 MHz is limited to communications with pilots regarding the movement and docking of ships. Normal output power must not exceed 1 watt. 5: 156.375 MHz and 156.650 MHz are available primarily for intership navigational communications. These frequencies are available between coast and ship on a secondary basis when used on or in the vicinity of locks or drawbridges. Normal output power must not exceed 1 watt. Maximum output power must not exceed 10 watts for coast stations or 25 watts for ship stations. 11. On the Great Lakes, in addition to bridge-to-bridge communications, 156.650 MHz is available for vessel control purposes in established vessel traffic systems. 156.650 MHz is not available for use in the Mississippi River from South Pass Lighted Whistle Buoy “2” and Southwest Pass entrance Mid-channel Lighted Whistle Buoy to mile 242.4 above Head of Passes near Baton Rouge. Additionally, it is not available for use in the Mississippi River-Gulf Outlet, the Mississippi River-Gulf Outlet Canal, and the Inner Harbor Navigational Canal, except to aid the transition from these areas. 12. Use of 156.375 MHz is available for navigational communications only in the Mississippi River from South Pass Lighted Whistle Buoy “2” and SouthPage 138 GX6000 13. 14. 15. 16. 17. 18. west Pass entrance Mid channel Lighted Whistle Buoy to mile 242.4 above head of Passes near Baton Rouge, and in addition over the full length of the Mississippi River-Gulf Outlet Canal from entrance to its junction with the Inner Harbor Navigation Canal, and over the full length of the Inner Harbor Navigation Canal from its junction with the Mississippi River to its entry to Lake Pontchartrain at the New Seabrook vehicular bridge. Within 120 km (75 miles) of the United States/Canada border, in the area of the Puget Sound and the Strait of Juan de Fuca and its approaches, 157.425 MHz is half of the duplex pair designated as Channel 88. In this area, Channel 88 is available to ship stations for communications with public coast stations only. More than 120 km (75 miles) from the United States/Canada border in the area of the Puget Sound and the Strait of Juan de Fuca, its approaches, the Great Lakes, and the St. Lawrence Seaway, 157.425 MHz is available for intership and commercial communications. Outside Puget Sound area and its approaches and the Great Lakes, 157.425 MHz is also available for communications between commercial fishing vessels and associated aircraft while engaged in commercial fishing activities. When the frequency 156.850 MHz is authorized, it may be used additionally for search and rescue training exercises conducted by state or local governments. The frequency 156.850 MHz is additionally available to coast stations on the Great Lakes for transmission of scheduled Coded Marine Weather Forecasts (MAFOR), Great Lakes Weather Broadcast (LAWEB) and scheduled Notices to Mariners or Bulletins. F3C and J3C emissions are permitted. Coast Stations on the Great Lakes must cease weather broadcasts which cause interference to stations operating on 156.800 MHz until the interference problem is resolved. The frequency 157.100 MHz is authorized for search and rescue training exercises by state or local government in conjunction with U.S. Coast Guard stations. Prior U.S. Coast Guard approval is required. Use must cease immediately on U.S. Coast Guard request. The duplex pair for channel 20 (157.000/161.600 MHz) may be used for ship to coast station communications. Available for assignment to coast stations, the use of which is in accord with an agreed program, for the broadcast of information to ship stations concerning the environment. GX6000 Page 139 CH 01 01A 02 03 03A 04 04A 05 05A 06 07A 08 09 10 11 12 13 14 15 07 15 16 17 18 18A 19 1019 2019 19A 19A 20 1020 2020 20A 21 21A 21B 22 22A 23 23A Page 140 VHF MARINE CHANNEL CHART S/D TX RX CHANNEL USE D 156.050 160.650 Public Correspondence (Marine Operator) Port Operation and Commercial. 156.050 VTS in selected areas D 156.100 160.700 Public Correspondence (Marine Operator) D 156.150 160.750 Public Correspondence (Marine Operator) U.S. Government Only, Coast Guard 156.150 Correspondence (Marine Operator), D 156.200 160.800 Public Port operation, ship movement Pacific coast: Coast Guard, East Coast: 156.200 Commercial fishing Correspondence (Marine Operator), D 156.250 160.850 Public Port operation, ship movement 156.250 Port operation. VTS in Seattle 156.300 Inter-ship Safety Correspondence (Marine Operator), D 156.350 160.950 Public Port operation, ship movement 156.350 Commercial 156.400 Commercial (Inter-ship only) Boater Calling channel, Commercial & 156.450 Non-commercial (Recreational) 156.500 Commercial 156.550 Commercial. VTS in selected areas. 156.600 Port operation. VTS in selected areas. Inter-ship Navigation Safety (Bridge-toS 156.650 bridge) 156.700 Port operation. VTS in selected areas. --156.750 Environmental (Receive only) Commercial, non-commercial, ship 156.750 movement (1 W) 156.800 International Distress, Safety and Calling 156.850 State Controlled (1 W) D 156.900 161.500 Port operation, ship movement 156.900 Commercial D 156.950 161.550 Port operation, ship movement 156.950 161.550 156.950 US: Commercial 156.950 Coast Guard Coast Guard Only, D 157.000 161.600 Canadian International: port operations and shipment 157.000 161.600 157.000 Port operation D 157.050 161.650 Port operation, ship movement U.S. Government Only, Canadian Coast 157.050 Guard --161.650 CMB Service D 157.100 161.700 Port operation, ship movement US and Canadian Coast Guard Liaison 157.100 and Maritime Safety Information Broadcasts announced on channel 16 D 157.150 161.750 Public Correspondence (Marine Operator) 157.150 U.S. Government Only GX6000 CH 23B 24 25 25B 26 27 28 28B 60 61 61A 62A 63 64 64A S/D 62 63A 66A 67 68 69 70 71 72 73 65 65A 66 GX6000 VHF MARINE CHANNEL CHART TX RX CHANNEL USE --161.750 CMB Service 157.200 161.800 Public Correspondence (Marine Operator) 157.250 161.850 Public Correspondence (Marine Operator) --161.850 CMB Service 157.300 161.900 Public Correspondence (Marine Operator) 157.350 161.950 Public Correspondence (Marine Operator) 157.400 162.000 Public Correspondence (Marine Operator) --162.000 CMB Service 156.025 160.625 Public Correspondence (Marine Operator) Correspondence (Marine Operator), 156.075 160.675 Public Port operation, ship movement Public Coast: Coast Guard; 156.075 East Coast: commercial fishing only Correspondence (Marine Operator), 156.125 160.725 Public Port operation, ship movement Public Coast: Coast Guard; 156.125 East Coast: commercial fishing only Correspondence (Marine Operator), 156.175 160.775 Public Port operation, ship movement Port Operation and Commercial. 156.175 VTS in selected areas. Correspondence (Marine Operator), 156.225 160.825 Public Port operation, ship movement Public Correspondence (Marine 156.225 Operator), Port operation, ship movement Correspondence (Marine Operator), 156.275 160.875 Public Port operation, ship movement 156.275 Port Operations Correspondence (Marine Operator), 156.325 160.925 Public Port operation, ship movement 156.325 Port Operations US: Commercial. Used for Bridgeto-bridge communications in lower 156.375 Mississippi River. Inter-ship only. Canada: Commercial fishing, S&R 156.425 Non-commercial (Recreational) US: Non-commercial (Recreational), Canada: Commercial fishing only, 156.475 International: Inter-ship, Port operations and Ship movement selective calling (voice --156.525 Digital communications not allowed) US, Canada: Non-commercial (Recreational), 156.575 International: Port operations and Ship movement 156.625 Non-commercial (Inter-ship only) US: Port Operations, Canada: Commercial fishing only, 156.675 International: Inter-ship, Port operations and Ship movement Page 141 VHF MARINE CHANNEL CHART TX RX CHANNEL USE US: Port Operations, Canada: Commercial fishing only, 74 X X X 156.725 International: Inter-ship, Port operations and Ship movement 75 X X X 156.775 Port Operations (Inter-ship only) (1W) 76 X X X 156.825 Port Operations (Inter-ship only) (1W) 77 X X 156.875 Port Operations (Inter-ship only) (1W) 77 156.875 Port Operations (Inter-ship only) Correspondence (Marine Operator), 78 D 156.925 161.525 Public Port operation, ship-movement 1078 156.925 2078 161.525 78A X X 156.925 Non-commercial (Recreational) 79 D 156.975 161.575 Port operation and Ship movement 1079 156.975 2079 161.575 79A X X 156.975 Commercial 80 D 157.025 161.625 Port operation, ship movement 80A X X 157.025 Commercial 81 D 157.075 161.675 Port operation, ship movement U.S. Government Only 81A 157.075 Environmental protection operations. 81A 157.075 Canadian Coast Guard Only Correspondence (Marine Operator), 82 D 157.125 161.725 Public Port operation, ship movement U.S. Government Only, 82A X X 157.125 Canadian Coast Guard Only 83 D 157.175 161.775 Public Correspondence (Marine Operator) U.S. Government Only, 83A X X 157.175 Canadian Coast Guard Only 83B --161.775 CMB Service 84 X X X D 157.225 161.825 Public Correspondence (Marine Operator) 85 X X X D 157.275 161.875 Public Correspondence (Marine Operator) 86 X X X D 157.325 161.925 Public Correspondence (Marine Operator) 87 X X 157.375 Port operation, ship movement 87A 157.375 Public Correspondence (Marine Operator) 88 X X 157.425 Port operation, ship movement 88A 157.425 Commercial, Inter-ship Only WX01 X X X --162.550 Weather (receive only) WX02 X X X --162.400 Weather (receive only) WX03 X X X --162.475 Weather (receive only) WX04 X X X --162.425 Weather (receive only) WX05 X X X --162.450 Weather (receive only) WX06 X X X --162.500 Weather (receive only) WX07 X X X --162.525 Weather (receive only) WX08 X X X --161.650 Weather (receive only) WX09 X X X --161.775 Weather (receive only) WX10 X X X --163.275 Weather (receive only) NOTE: Simplex channels, 03A, 21A, 23A, 61A, 64A, 81A, 82A and 83A CANNOT be lawfully used by the general public in U.S.A. waters. CH Page 142 S/D GX6000 23 WARRANTY Marine Products Limited Warranty PLEASE NOTE The following “Limited Warranty” is for valid for products that have been purchased in the United States and Canada. For limited Warranty details outside the United States, contact the dealer in your country. STANDARD HORIZON (a division of YAESU U.S.A.) warrants, to the original purchaser only, each new Marine Communications Product (“Product”) manufactured and/or supplied by STANDARD HORIZON against defects in materials and workmanship under normal use and service for a period of time from the date of purchase as follows: Fixed Mount and Portable Transceivers 1 year - if purchased before 01/01/91 3 years - if purchased between 01/01/91 and 01/01/94 3 years Waterproof - if purchased after 01/01/94 Loud hailers 1 year - if purchased before 01/01/91 3 years - if purchased after 01/01/91 Associated Chargers 1 year - if purchased before 01/01/91 3 years - if purchased after 01/01/91 Associated Batteries - 1 year. Note: Batteries will be deemed deflective only if storage capacity drops below 80% of rated capacity or if leakage develops. Associated Accessories - 1 year. Includes: Microphones/Handsets, External Speakers, Antennas, Carrying Accessories, Power Supplies, and Signaling Boards. To receive warranty service, the purchaser must deliver the Product, transportation and insurance prepaid, to STANDARD HORIZON, Attention Marine repairs 6125 Phyllis Drive, Cypress, California 90630, U.S.A. Include proof of purchase indicating model. serial number, and date of purchase. STANDARD HORIZON will return the Product to the purchaser freight prepaid. Products purchased prior to January 1, 1991 will bear the STANDARD HORIZON warranty terms in effect prior to that date. In the event of a defect, malfunction or failure of the Product during the warranty period, STANDARD HORIZON’s liability for any breach of contract or any breach of express or implied warranties in connection with the sale of Products shall be limited solely to repair or replacement, at its option, of the Product or GX6000 Page 143 part(s) therein which, upon examination by STANDARD HORIZON, appear to be defective or not up to factory specifications. STANDARD HORIZON may, at its option, repair or replace parts or subassemblies with new or reconditioned parts and subassemblies. Parts thus repaired or replaced are warranted for the balance of the original applicable warranty. STANDARD HORIZON will not warrant installation, maintenance or service of the Products. In all instances, STANDARD HORIZON’s liability for damages shall not exceed the purchase price of the defective Product. This warranty only extends to Products sold within the 50 States of the United States of America and the District of Columbia. STANDARD HORIZON will pay all labor to repair the product and replacement parts charges incurred in providing the warranty service except where purchaser abuse or other qualifying exceptions exist. The purchaser must pay any transportation expenses incurred in returning the Product to STANDARD HORIZON for service. This limited warranty does not extend to any Product which has been subjected to misuse, neglect, accident, incorrect wiring by anyone other than STANDARD HORIZON, improper installation, or subjected to use in violation of instructions furnished by STANDARD HORIZON, nor does this warranty extend to Products on which the serial number has been removed, defaced, or changed. STANDARD HORIZON cannot be responsible in any way for ancillary equipment not furnished by STANDARD HORIZON which is attached to or used in connection with STANDARD HORIZON’s Products, or for the operation of the Product with any ancillary equipment, and all such equipment is expressly excluded from this warranty. STANDARD HORIZON disclaims liability for range, coverage, or operation of the Product and ancillary equipment as a whole under this warranty. STANDARD HORIZON reserves the right to make changes or improvements in Products, during subsequent production, without incurring the obligation to install such changes or improvements on previously manufactured Products. The implied warranties which the law imposes on the sale of this Product are expressly LIMITED, in duration, to the time period specified above. STANDARD HORIZON shall not be liable under any circumstances for consequential damages resulting from the use and operation of this Product, or from the breach of this LIMITED WARRANTY, any implied warranties, or any contract with STANDARD HORIZON. IN CONNECTION WITH THE SALE OF ITS PRODUCTS, STANDARD HORIZON MAKES NO WARRANTIES, EXPRESS OR IMPLIED AS TO THE MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE, EXCEPT AS EXPRESSLY SET FORTH HEREIN. Page 144 GX6000 Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitation on how long an implied warranty lasts, so the above limitations or exclusions may not apply. This warranty gives specific legal rights, and there may be other rights which may vary from state to state. ONLY PRODUCTS SOLD ON OR AFTER JANUARY 1, 1991 ARE COVERED UNDER THE TERMS OF THIS LIMITED WARRANTY. ON-LINE WARRANTY REGISTRATION THANK YOU for buying STANDARD HORIZON (a division of YAESU U.S.A.) products! We are confident your new radio will serve your needs for many years! Please visit www.standardhorizon.com to register your Marine VHF. It should be noted that visiting the website from time to time may be beneficial to you, as new products are released they will appear on the STANDARD HORIZON website. Also a statement regarding product support should be added to the manual. Product Support Inquiries If you have any questions or comments regarding the use of the radio, you can visit the STANDARD HORIZON website to send an E-Mail or contact the Product Support team at (714) 827-7600 ext 6300 M-F 8:00-5:00 PST. In addition to the warranty, STANDARD HORIZON includes a lifetime “flat rate” and “customer loyalty” programs to provide service after the warranty period has expired. If you wish to obtain the flat rate price for out-of-warranty repair, you must include the information on the Owner’s Record with the unit when you return it to your Dealer or to STANDARD HORIZON. Lifetime Flat Rate Service Program: For the original Owner only, for the lifetime of the unit, STANDARD HORIZON will repair the unit to original specifications. Note: The flat rate amount is payable by the Owner only if STANDARD HORIZON or the STANDARD HORIZON Dealer determines that a repair is needed. After the repair, a 90-day warranty will be in effect from the date of return of the unit to the Owner. This service program is not available for equipment which has failed as a result of neglect, accident, breakage, misuse, improper installation or modification, or water damage (depending on the product). GX6000 Page 145 24 SPECIFICATIONS Performance specifications are nominal, unless otherwise indicated, and are subject to change without notice. Measured in accordance with TIA/EIA-603. 24.1 GENERAL 24.2 TRANSMITTER 24.3 RECEIVER (for Voice and DSC) Channels............................................................... All USA, International and Canadian Normal Input Voltage...................................................................................... 13.8 V DC Operating Voltage Range......................................................................... 11 V to 16.5 V Current Drain Standby............................................................................................................0.55 A Receiver (at Maximum AF Output)....................................................................0.9 A Transmit.................................................................................... 5.0 A (Hi), 1.0 A (Lo) DSC Transmitted Call Log...........................................................................................24 DSC Distress Call Log.................................................................................................27 DSC Received Call Log...............................................................................................64 Individual Call Directory...............................................................................................80 Group Call Directory....................................................................................................32 Waypoint Directory....................................................................................................100 Display Type................................................................................ 2.8” x 2” (70 x 51 mm) Full Dot Matrix (222 x 162 pixels) Dimensions (WxHxD)................................. 6.9” x 4.3” x 6.8” (175.5 x 110 x 173.3 mm) Flush-Mount Dimensions (WxHxD)............. 6.2” x 3.7” x 6.2” (157.4 x 93.4 x 158 mm) Weight .................................................................................................. 3.7 lbs (1.66 kg) Frequency Range................................................. 156.025 MHz to 157.425 MHz (USA) 156.025 MHz to 161.600 MHz (INTERNATIONAL) RF Output Power..............................................................................25 W (Hi), 1 W (Lo) Conducted Spurious Emissions.......................... Less than −80 dBc (Hi), −66 dBc (Lo) Audio Response.......................................................... within +1/−3dB of a 6 dB/Octave pre-emphasis characteristic at 300 to 3000 Hz Audio Distortion........................................................................................Less than 5 % Modulation....................................................16K0G3E (for Voice), 16K0G2B (for DSC) Frequency Stability..........................................................±0.0003 % (−20 °C to +60 °C) FM Hum and Noise............................................................................................... 50 dB Frequency Range............................................................156.050 MHz to 163.275 MHz Sensitivity 20 dB Quieting.............................................................................................. 0.35 µV 12 dB SINAD................................................................................................ 0.30 µV Squelch Sensitivity (Threshold).................................................................... 0.13 µV Modulation Acceptance Bandwidth.................................................................. ±7.5 kHz Selectivity (Typical) Spurious and Image Rejection................................80 dB for Voice (75 dB for DSC) Intermodulation and Rejection................................80 dB for Voice (75 dB for DSC) Audio Output................................................ 10 W (at 8 ohms external speaker output) Audio Response.......................................................... within +1/–3dB of a 6 dB/Octave de-emphasis characteristic at 300 to 3000 Hz Page 146 GX6000 Frequency Stability..........................................................±0.0003 % (–20 °C to +60 °C) Channel Spacing................................................................................................. 25 kHz DSC Format...........................................................................................ITU-R M.493-13 Attenuator (Local).....................................................................................Approx. 10 dB 24.4 RECEIVER (for AIS) 24.5 NMEA INPUT/OUTPUT 24.6 SCU-31 EXTERNAL GPS ANTENNA (Optional) Frequency.................................................. 161.975 MHz (CH A), 162.025 MHz (CH B) Sensitivity................................................................................ 0.5 µV (at 12 dB SINAD) Selectivity(Typical) Spurious and Image Rejection......................................................................... 70 dB Intermodulation and Rejection......................................................................... 70 dB 4800 Baud selected: NMEA 0183 Input (4800 baud)............................GGA, GLL, GNS, RMC, GSA, & GSV NMEA 0183 Output (4800 baud)......................................DSC, DSE, GGA, GLL, GNS, RMC, GSA & GSV NMEA 0183-HS AIS Output (38400 baud)............................................................. VDM 38400 Baud selected: NMEA 0183-HS Input (38400 baud)....................GGA, GLL, GNS, RMC, GSA, & GSV NMEA 0183-HS Output (38400 baud)..............................DSC, DSE, GGA, GLL, GNS, RMC, GSA, GSV VDM NMEA 0183-HS AIS Output (38400 baud)............................................................. VDM Receiver Channels..................................................................................... 66 Channels Sensitivity.......................................................................................Less than –147 dBm Time to First Fix...............................................................1 minute typical (@Cold Start) 5 seconds typical (@ Hot Start) Geodetic Datum................................................................................................ WGS84 GX6000 Page 147 24.7 DIMENSIONS 6.2" (155.4 mm) 6" (152.4 mm) 1" (26.3 mm) 5.7" (147 mm) 4.3" (108 mm) 3.6" (91.4 mm) 4.33" (110 mm) 6.9" (175.5 mm) 1.8" (45.4 mm) 1.9" (48.5 mm) 6.1" (155.4 mm) 6" (152.4 mm) 1" (26.3 mm) 3.6" (91.4 mm) 1" (25 mm) 6.6" (168.4 mm) 3.3" (84 mm) 1.8" (45.4 mm) Page 148 5.8" (147 mm) 4.3W" (108 mm) 5.3" (135 mm) 4.3" (110 mm) 4.3" (110 mm) 6.9" (175.5 mm) 1.9" (48.5 mm) GX6000 25 FCC RADIO LICENSE INFORMATION Standard Horizon radios comply with the Federal Communication Commission (FCC) requirements that regulate the Maritime Radio Service. 25.1 STATION LICENSE 25.2 RADIO CALL SIGN 25.3 CANADIAN SHIP STATION LICENSING An FCC ship station license is no longer required for any vessel traveling in U.S. waters (except Hawaii) which is under 20 meters in length. However, any vessel required to carry a marine radio on an international voyage, carrying a HF single side band radiotelephone or marine satellite terminal is required to have a ship station license. FCC license forms, including applications for ship (605) and land station licenses can be downloaded via the Internet at https://www.fcc.gov/fcc-form-605. To obtain a form from the FCC, call (888) 225-5322. Currently the FCC does not require recreational boaters to have a Ship Radio Station License. The USCG recommends the boats registration number and the state to be used when calling another vessel. You may need a license when traveling in Canada. If you do need a license contact their nearest field office or regional office or write: Industry Canada Radio Regulatory Branch Attn: DOSP 300 Slater Street Ottawa, Ontario Canada, KIA 0C8 25.4 FCC / INDUSTRY CANADA INFORMATION The following data pertaining to the transceiver is necessary to fill out the license application. Type Acceptance........................................................................... FCC Part 80 Output Power.................................................1 Watt (low) and 25 Watts (high) Emission...........................................................................16K0G3E, 16K0G2B Frequency Range.......................................................156.025 to 163.275 MHz FCC Type Number..................................................................... K6630593X3D Industry Canada Type Approval............................................. 511B-30593X3D GX6000 Page 149 26 FCC NOTICE NOTICE Unauthorized changes or modifications to this equipment may void compliance with FCC Rules. Any change or modification must be approved in writing by STANDARD HORIZON. NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. WARNING It is a violation of the rules of the Federal Communications Commission to input an MMSI that has not been properly assigned to the end user, or to otherwise input any inaccurate data in this device. Page 150 GX6000 GX6000 Page 151 THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. Changes or modifications to this device not expressly approved by YAESU U.S.A. could void the User’s authorization to operate this device. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope rayonnée quivalente (p.i.r.e.) ne dépassepas l’intensité nécessaire à l’établissement d’une communication satisfaisante. This radio transmitter (identify the device by certification number, or model number if Category II) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Le présent émetteur radio (identifier le dispositif par son numéro de certification ou son numéro de modèle s’il fait partie du matériel de catégorie I) a été approuvé par Industrie Canada pour fonctionner avec les types d’antenne énumérés ci-dessous et ayant un gain admissible maximal et l’impédance requise pour chaque type d’antenne. Les types d’antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l’exploitation de l’émetteur. l’établissement d’une communication satisfaisante. CAN ICES-3 (B) / NMB-3 (B) Page 152 GX6000 cut here 10 158 mm Use this template to mark the location where the rectangular hole for the flush mount is to be cut. TEMPLATE for the GX6000 94 mm Page 153
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.7 Linearized : Yes Author : YAESU MUSEN CO., LTD. Create Date : 2017:04:20 08:42:53+09:00 Modify Date : 2017:12:28 14:34:08-05:00 XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Metadata Date : 2017:12:28 14:34:08-05:00 Creator Tool : Adobe InDesign CS6 (Windows) Format : application/pdf Title : GX6000 Owner's Manual Creator : YAESU MUSEN CO., LTD. Document ID : uuid:112d15f1-a9de-4850-adcb-22217bc0dc57 Instance ID : uuid:6308761d-b2c0-4f46-95e0-168fea11ca79 Producer : Adobe PDF Library 10.0.1 Page Count : 33EXIF Metadata provided by EXIF.tools