Yaesu Musen 30593X3D MOBILE MARINE TRANSCEIVER User Manual GX6000 Owner s Manual

Yaesu Musen Co., Ltd. MOBILE MARINE TRANSCEIVER GX6000 Owner s Manual

OM User Manual 7

Page 84 GX600011 NAVIGATIONThe GX6000 is capable of storing up to 250 waypoints for navigation using the compass page.You can also navigate to DSC distress calls with position or a position received from another DSC radio using DSC polling.11.1 WAYPOINT OPERATION11.1.1 Starting and Stopping NavigationNavigation by Using the Waypoint Directory1. []  “NAVI”  “WAYPOINT”2. Rotate the DIAL/ENT knob to select the desired category (“HISTORY” or “MEMORY”), then press the [SELECT] soft key.3. Rotate the DIAL/ENT knob to select a waypoint, then press the [SELECT] soft key. The navigation screen will appear. The screen includes the distance and direction to the destination, and the waypoint is indicated by a dot () inside the compass. 4. Press one of the soft keys to show the key selections. Press the [STOP] soft key to stop the navigation.Navigation by Manually Entering a Waypoint1. []  “NAVI”  “WAYPOINT”2. Rotate the DIAL/ENT knob to select “MANUAL”, then press the [SELECT] soft key.3. If you want to give the waypoint an easy-to-nd name, rotate the DIAL/ENT knob to select “NAME:”, press the [SELECT] soft key, then enter the name. For details, refer to “10.4.1 Setting up the Individual / Position Call Directory”.
Page 85GX60004. Rotate the DIAL/ENT knob to select “POSITION:”, then press the [SELECT] soft key.5. Rotate the DIAL/ENT knob to select the rst number of latitude, then press the [SELECT] soft key to step to the next number. 6. Repeat step 5 to set the position. If a mistake was made, rotate the DIAL/ENT knob to select “←” or “→”, press the [SELECT] soft key until the wrong character is selected, then perform step 5.7. When nished programming the position, press the [FINISH] soft key. The display will return to the previous screen.8. Rotate the DIAL/ENT knob to select “SAVE & GOTO”, then press the [SELECT] soft key. To set the Waypoint as a temporary destination without saving and start the navigation, select “GOTO” and press the [SELECT] soft key. The navigation screen will appear. The screen includes the distance and direction to the destination, and the waypoint is indicated by a dot () inside the compass.9. Press one of the soft keys to show the key selections. Press the [STOP] soft key to stop the navigation.11.1.2 Setting Up Waypoint DirectoryMarking a PositionThis feature allows the radio to mark the current position of the vessel.1. []  “SETUP”  “WAYPOINT SETUP”  “MARK POSITION”2. Rotate the DIAL/ENT knob to select “NAME:”, then press the [SELECT] soft key. 3. Enter the waypoint name by rotating the DIAL/ENT knob and the [SELECT] soft key. When nished entering the name (using fteen char-acters or less), press the [FINISH] soft key.
Page 86 GX60004. If you want to modify the position, rotate the DIAL/ENT knob to select “POSITION:”, press the [SELECT] soft key, then enter the new coordinates. When nished modifying the position, press the [FINISH] soft key.5. Rotate the DIAL/ENT knob to select “SAVE”, then press the [SELECT] soft key to save the mark posi-tion into memory. 6. Press the CLEAR key to return to radio operation.Adding a Waypoint1. []  “SETUP”  “WAYPOINT SETUP”  “WAYPOINT DIRECTORY”2. Rotate the DIAL/ENT knob to select “ADD”, then press the [SELECT] soft key.3. Rotate the DIAL/ENT knob to select “NAME:”, then press the [SELECT] soft key. 4. Enter the waypoint name by rotating the DIAL/ENT knob and the [SELECT] soft key. When nished entering the name (using fteen char-acters or less), press the [FINISH] soft key.5. Rotate the DIAL/ENT knob to select “POSITION:”, press the [SELECT] soft key, then enter the coordinates. When nished entering the position, press the [FINISH] soft key.6. Rotate the DIAL/ENT knob to select “SAVE”, then press the [SELECT] soft key to save the waypoint into memory. 7. Press the CLEAR key to return to radio operation.Editing a WaypointThis function allows a previously entered waypoint to be edited. 1. []  “SETUP”  “WAYPOINT SETUP”  “WAYPOINT DIRECTORY”2. Rotate the DIAL/ENT knob to select “EDIT”, then press the [SELECT] soft key.
Page 87GX60003. Rotate the DIAL/ENT knob to select the waypoint to be edited, then press the [SELECT] soft key to show the waypoint input display. 4. Rotate the DIAL/ENT knob to select “NAME:” or “POSITION:”, then press the [SELECT] soft key.5. Rotate the DIAL/ENT knob to select “←” or “→”, press the [SELECT] soft key until the character to be changed is selected, then enter a new character. 6. Repeat step 5 until the waypoint is updated. When nished editing, press the [FINISH] soft key.7. Rotate the DIAL/ENT knob to select “SAVE”, then press the [SELECT] soft key to store the edited waypoint into memory.8. Press the CLEAR key to return to radio operation.Deleting a Waypoint1. []  “SETUP”  “WAYPOINT SETUP”  “WAYPOINT DIRECTORY”2. Rotate the DIAL/ENT knob to select “DELETE”, then press the [SELECT] soft key.3. Rotate the DIAL/ENT knob to select the waypoint to be deleted, then press the [SELECT] soft key. 4. Conrm the waypoint to be deleted, rotate the DIAL/ENT knob to select “OK”, then press the [SELECT] soft key. 5. Press the CLEAR key to return to radio operation.Saving a DSC Position Call as a WaypointWhen a position is received from another DSC radio the GX6000 allows the position to be saved as a waypoint.Refer to section “10.7.4 Saving the Reported Position as a Waypoint” for details.
Page 88 GX600011.1.3 Selecting the Display RangeThis menu item allows setting of the range on the compass display. 1. []  “SETUP”  “WAYPOINT SETUP”  “DISPLAY RANGE”2. Rotate the DIAL/ENT knob to select desired range. (Unit of measure depends on the settings in the GPS SETUP menu. Refer to section “18.7 UNITS OF MEASURE”.)3. Press the [ENTER] soft key to store the selected setting.4. Press the CLEAR key to return to radio operation.11.1.4 Selecting the Arrival RangeThis menu item sets the distance to alert you when you are within the specied arrival range of the waypoint.1. []  “SETUP”  “WAYPOINT SETUP”  “ARRIVAL RANGE”2. Rotate the DIAL/ENT knob to select desired range. (Unit of measure depends on the settings in the GPS SETUP menu. Refer to section “18.7 UNITS OF MEASURE”.)3. Press the [ENTER] soft key to store the selected setting.4. Press the CLEAR key to return to radio operation.11.2 ROUTING OPERATIONThe GX6000 allows you to set 1 to 15 waypoints along the route.Current positionWPTVia1Via2Via3Via14Via15Routing to a Waypoint11.2.1 Setting Up Routing DirectoryNOTEAll the destinations and via-points must be programmed as waypoints in the GX6000 memory. Refer to section “11.1.2 Setting Up Waypoint Directory”.
Page 89GX6000Adding a Route1. []  “SETUP”  “WAYPOINT SETUP”  “ROUTE DIRECTORY”2. Rotate the DIAL/ENT knob to select “ADD”, then press the [SELECT] soft key.3. Rotate the DIAL/ENT knob to select “NAME:”, then press the [SELECT] soft key. 4. Enter the route name by rotating the DIAL/ENT knob and the [SELECT] soft key. When nished entering the name (using fteen char-acters or less), press the [FINISH] soft key.5. Rotate the DIAL/ENT knob to select “ROUTE POINTS”, press the [SELECT] soft key. 6. Rotate the DIAL/ENT knob to select “WPT:”, then press the [SELECT] soft key. 7. Rotate the DIAL/ENT knob to select a waypoint, then press the [SELECT] soft key. 8. Rotate the DIAL/ENT knob to select “Via1”, then press the [SELECT] soft key. 9. Rotate the DIAL/ENT knob to select a waypoint, then press the [SELECT] soft key. 10. Repeat steps 8 and 9 to add more via-points.11. Press the [BACK] soft key. 12. Rotate the DIAL/ENT knob to select “SAVE”, then press the [SELECT] soft key to store the route into memory. 13. Press the CLEAR key to return to radio operation.Editing a RouteThis function allows a previously entered route to be edited. 1. []  “SETUP”  “WAYPOINT SETUP”  “ROUTE DIRECTORY”
Page 90 GX60002. Rotate the DIAL/ENT knob to select “EDIT”, then press the [SELECT] soft key.3. Rotate the DIAL/ENT knob to select the route to be edited, then press the [SELECT] soft key to show the route input display. 4. Perform steps 3 to 11 of the previous page until the route is updated.5. Rotate the DIAL/ENT knob to select “SAVE”, then press the [SELECT] soft key to store the edited route into memory. 6. Press the CLEAR key to return to radio operation.Deleting a Route1. []  “SETUP”  “WAYPOINT SETUP”  “ROUTE DIRECTORY”2. Rotate the DIAL/ENT knob to select “DELETE”, then press the [SELECT] soft key.3. Rotate the DIAL/ENT knob to select the route to be deleted, then press the [SELECT] soft key. 4. Conrm the route to be deleted, rotate the DIAL/ENT knob to select “OK”, then press the [SELECT] soft key. 5. Press the CLEAR key to return to radio operation.11.2.2 Starting and Stopping Route Navigation1. []  “NAVI”  “ROUTE”2. Rotate the DIAL/ENT knob to select the desired category (“HISTORY” or “MEMORY”), then press the [SELECT] soft key.
Page 91GX60003. Rotate the DIAL/ENT knob to select a route, then press the [SELECT] soft key. The navigation screen with “RUT” indicator appears. 4. A message “ARRIVED” will appear when you have reached to the rst target point. To start navigation to the next target, press the [YES] soft key. 5. Press one of the soft keys to show the key selections. Press the [STOP] soft key to stop the navigation.11.2.3 Changing the Destination1. On the navigation screen, press one of the soft keys to show the key selections.2. Press the [NEXT TG] soft key.3. Rotate the DIAL/ENT knob to select desired destina-tion, then press the [SELECT] soft key.4. The navigation screen with a new destination appears.11.2.4 Selecting Automatic or Manual RoutingThis selection allows you to start navigation to the next target automatically or manually when your vessel has arrived at a waypoint.1. []  “SETUP”  “WAYPOINT SETUP”  “ROUTING OPERATION”2. Rotate the DIAL/ENT knob to select “AUTO” or “MANUAL”, then press the [ENTER] soft key.3. Press the CLEAR key to return to radio operation.
Page 92 GX600012 GM OPERATIONThe GM (Group Monitor) feature of the GX6000 utilizes the same system as the DSC Group call and Auto Position Polling, to display the group members' locations. 12.1 SETTING UP GM OPERATIONThe GX6000 is capable of storing up to 10 groups with 1 to 9 members each.12.1.1 Setting Up GM Group DirectoryNOTE• For this function to operate, the same group MMSI must be programmed into each transceiver of group members to be monitored. Refer to section “10.5.1 Setting up a Group Call” for details.• Group members for GM operation can only be selected from the Individual/Position Call directory, there for all members that you want to monitor have to be stored in the directory. Refer to section “10.4.1 Setting up the Individual / Position Call Directory” for details.1. []  “SETUP”  “GM SETUP”  “GM GROUP DIRECTORY”2. Rotate the DIAL/ENT knob to select “ADD”, then press the [SELECT] soft key.3. Rotate the DIAL/ENT knob to select “NAME:”, then press the [SELECT] soft key. 4. Enter the route name by rotating the DIAL/ENT knob and the [SELECT] soft key. When nished entering the name (using eleven char-acters or less), press the [FINISH] soft key.5. Rotate the DIAL/ENT knob to select “GM ID:”, press the [SELECT] soft key, then enter the group MMSI number. When nished entering the MMSI, press the [FINISH] soft key.6. Rotate the DIAL/ENT knob to select “MEMBER”, then press the [SELECT] soft key.
Page 93GX60007. Rotate the DIAL/ENT knob to select a list number, then press the [SELECT] soft key.8. Rotate the DIAL/ENT knob to select a member from the Individual directory, then press the [SELECT] soft key. 9. Repeat steps 8 to add members to the group, then press the [BACK] soft key.10. Press the [BACK] soft key to return to the “NAME:” and “GM ID:” screen.11. Rotate the DIAL/ENT knob to select “SAVE” to store the data, then press the [ENTER] soft key. 12. To enter another group directory, repeat steps 2 through 11.13. Press the CLEAR key to return to radio operation.12.1.2 Setting Up the Polling Time Interval1. []  “SETUP”  “GM SETUP”  “INTERVAL”2. Rotate the DIAL/ENT knob to select the desired interval time, then press the [ENTER] soft key.3. Press the CLEAR key to return to radio operation.12.1.3 Enabling/Disabling Transmission during GM Operation1. []  “SETUP”  “GM SETUP”  “GM TX”2 Rotate the DIAL/ENT knob to select the desired transmission type, then press the [ENTER] soft key.OFF: Disables the transmission during GM operation.ON GM: Enables the transmission during the GM target display.ON ALL: Enables the transmission during the GM operation.3. Press the CLEAR key to return to radio operation.

Navigation menu