Yamaha 170602_mtx_mrx_xmv_ex_rcps_v310_rev10_en MTX3, MTX5 D, MRX7 XMV Series, EXi8, EXo8 Remote Control Protocol Specifications V3.1.0 Mtx Mrx Ex Spec V310 En

User Manual: Yamaha MTX3, MTX5-D, MRX7-D, XMV Series, EXi8, EXo8 Remote Control Protocol Specifications V3.1.0

Open the PDF directly: View PDF .
Page Count: 124

Download
Open PDF In Browser	View PDF

MTX3, MTX5-D, MRX7-D,
XMV Series, EXi8, EXo8
Remote Control Protocol Specifications
Version 3.1.0 rev10
Release   Jun 19th, 2017
This specification document applies to MTX3, MTX5-D, MRX7-D, XMV, EXi8, and EXo8 V3.10 and later.

Table of contents
0. Revision History............................................................................................................................... 4
1. Setup................................................................................................................................................. 8
1.1.

Connection Procedure.................................................................................................................................................... 8

1.2.

Configuring the Remote Controller................................................................................................................................. 9

1.3.

Device Configuration.................................................................................................................................................... 10
1.3.1. MTX3, MTX5-D and MRX7-D.......................................................................................................................... 10
1.3.2. XMV, EXi8 and EXo8....................................................................................................................................... 10
1.3.3. MRX7-D and Remote Control Setup List......................................................................................................... 10

2. Command List................................................................................................................................ 11
2.1.

Commands from a device sent to a remote controller.................................................................................................. 11

2.2.

Commands for controlling a device.............................................................................................................................. 11

2.3.

Extended commands.................................................................................................................................................... 12

3. Command Specifications.............................................................................................................. 13
3.1.

Basic Command Specifications.................................................................................................................................... 13

3.2.

Commands a Device Sends to a Remote Controller.................................................................................................... 14
3.2.1. Device status change notification..................................................................................................................... 14
3.2.2. Parameter change notification......................................................................................................................... 15
3.2.3. Meter information notification........................................................................................................................... 16
3.2.4. Preset change notification................................................................................................................................ 16
3.2.5. Snapshot change notification........................................................................................................................... 17
3.2.6. Event processing change notification............................................................................................................... 17

3.3.

Commands for controlling a device.............................................................................................................................. 20
3.3.1. Device status query.......................................................................................................................................... 20
3.3.2. Device run mode change................................................................................................................................. 21
3.3.3. MTX external control protocol run mode setting.............................................................................................. 22
3.3.4. Parameter query.............................................................................................................................................. 24
3.3.5. Parameter setting............................................................................................................................................. 26
3.3.6. Meter control.................................................................................................................................................... 30
3.3.7. Preset processing............................................................................................................................................ 32
3.3.8. Snapshot Recall processing............................................................................................................................. 32

3.4.

Extended commands.................................................................................................................................................... 33
3.4.1. Product information query request................................................................................................................... 33
3.4.2. Preset processing request............................................................................................................................... 35
3.4.3. Event processing request................................................................................................................................. 36

3.5.

Command Errors.......................................................................................................................................................... 50
3.5.1. Command Error Notifications........................................................................................................................... 50

4. Command Sequence...................................................................................................................... 51
4.1.

Communication start sequence.................................................................................................................................... 52

4.2.

Parameter sync sequence............................................................................................................................................ 54

4.3.

Parameter query sequence at any given time.............................................................................................................. 55

4.4.

Meter data request/query sequence............................................................................................................................. 56

4.5.

Preset recall request sequence.................................................................................................................................... 56

4.6.

Sequence when parameters are changed by another controller.................................................................................. 57

5. Meter Value..................................................................................................................................... 58
6. Parameter Value Details................................................................................................................ 59
6.1.

Fader parameter........................................................................................................................................................... 59
6.1.1. Fader with "-Infinity to 0dB" range.................................................................................................................... 59
6.1.2. Fader with "-Infinity to 10dB" range.................................................................................................................. 61

6.2.

Other parameters (MTX3, MTX5-D)............................................................................................................................. 63
6.2.1. INPUT PATCH................................................................................................................................................. 63
6.2.2. INPUT CHANNEL............................................................................................................................................ 64
6.2.2.1. 3BAND EQ....................................................................................................................................... 64
6.2.2.2. GATE............................................................................................................................................... 65
6.2.2.3. COMPRESSOR............................................................................................................................... 67
6.2.2.4. AGC................................................................................................................................................. 68
6.2.2.5. DUGAN AUTOMIXER...................................................................................................................... 69

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

2

Table of contents
6.2.3.
6.2.4.

6.2.5.

6.2.6.

6.2.7.

6.2.8.

6.3.

EFFECT........................................................................................................................................................... 70
ZONE............................................................................................................................................................... 71
6.2.4.1. PAGING (MTX5-D only)................................................................................................................... 71
6.2.4.2. 1st/2nd PRIORITY........................................................................................................................... 72
6.2.4.3. ANC.................................................................................................................................................. 73
ROUTER.......................................................................................................................................................... 73
6.2.5.1. ROUTER.......................................................................................................................................... 73
6.2.5.2. OSCILLATOR.................................................................................................................................. 74
OUTPUT CHANNEL........................................................................................................................................ 74
6.2.6.1. 4BAND EQ....................................................................................................................................... 74
6.2.6.2. SPEAKER PROCESSOR................................................................................................................ 75
OUTPUT PATCH............................................................................................................................................. 75
6.2.7.1. OUTPUT PATCH............................................................................................................................. 75
6.2.7.2. YDIF PATCH.................................................................................................................................... 76
MY4-AEC......................................................................................................................................................... 77
6.2.8.1. MY4-AEC Input Patch...................................................................................................................... 77
6.2.8.2. MY4-AEC FBS................................................................................................................................. 77

Other parameters (MRX7-D)........................................................................................................................................ 78
6.3.1. Ambient Noise Compensator........................................................................................................................... 78
6.3.2. Auto Gain Control............................................................................................................................................. 78
6.3.3. Combiner.......................................................................................................................................................... 78
6.3.3.1. Room Combiner............................................................................................................................... 78
6.3.3.2. Room Combiner plus Automixer...................................................................................................... 78
6.3.4. Dynamics......................................................................................................................................................... 78
6.3.4.1. Compressor...................................................................................................................................... 78
6.3.4.2. Gate/Ducking................................................................................................................................... 79
6.3.4.3. Limiter.............................................................................................................................................. 79
6.3.4.4. Paging Ducker.................................................................................................................................. 79
6.3.5. Effect................................................................................................................................................................ 80
6.3.6. EQ.................................................................................................................................................................... 81
6.3.6.1. GEQ................................................................................................................................................. 81
6.3.6.2. PEQ.................................................................................................................................................. 81
6.3.7. Filter................................................................................................................................................................. 81
6.3.7.1. HPF/LPF/BPF.................................................................................................................................. 81
6.3.8. Mixer................................................................................................................................................................ 81
6.3.8.1. Dugan Automixer............................................................................................................................. 81
6.3.9. Oscillator.......................................................................................................................................................... 82
6.3.10. Paging.............................................................................................................................................................. 82
6.3.11. Speech Privacy................................................................................................................................................ 82
6.3.12. Speaker Processor........................................................................................................................................... 82
6.3.13. MY4-AEC (MTX5-D only)................................................................................................................................. 82
6.3.13.1. MY4-AEC FBS................................................................................................................................. 82

7. Parameter List................................................................................................................................ 83
7.1.

MTX3/MTX5-D.............................................................................................................................................................. 83

7.2.

MRX7-D...................................................................................................................................................................... 101

7.3.

XMV Series................................................................................................................................................................. 107

7.4.

EXi8............................................................................................................................................................................ 108

7.5.

EXo8........................................................................................................................................................................... 109

7.6.

MY4-AEC.................................................................................................................................................................... 110
7.6.1. MTX3, MTX5-D.............................................................................................................................................. 110
7.6.2. MRX7-D......................................................................................................................................................... 110

8. Meter List...................................................................................................................................... 111
8.1.

MTX3/MTX5-D............................................................................................................................................................ 111

8.2.

MRX7-D...................................................................................................................................................................... 114

8.3.

XMV Series................................................................................................................................................................. 122

8.4.

EXi8............................................................................................................................................................................ 123

8.5.

EXo8........................................................................................................................................................................... 124

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

3

0. Revision History
Version
V1.0.0
V1.0.1

Date
Sep. 1, 2013
Sep. 25, 2013

V1.0.2

Jan.14, 2014

V1.0.3

May 23, 2014

V1.3.0

Nov. 1, 2014

V2.0.3

Aug. 25, 2015

V2.1.0

Dec. 22, 2015

Section
7
7
8
3.1
3.1
3.2.4
3.2.4, 3.4.3
3.2.4, 3.4.3
3.3.1
3.3.3
3.4.3
4
4
6
7
7
7
8
3.3.1, 4

Description
Initial version
Added note (*1) to XMV "InputSelect" parameter
Added *2 to XMV "ATT" and "DigitalATT"
Separated Meter List of EXi8 and EXo8
Added Heart beat command
Added explanation for escape character
Added note for "1-10) Time synchronization notification "
Added time set and get commands
Added DST related commands
Added note for "2-1) Device run mode query"
Modified description text and added note for "2-9) Keepalive activation setting"
Added alert event log related commands
Fixed text "devstatus devmode" to "devstatus runmode" in communication start process explanation
Fixed communication start process flow diagram
Added parameter value detail for MY4-AEC (table 12, 13, 14)
Added parameter "MYInsert 16 Channel" to Parameter List
Added MY4-AEC parameters to Parameter List
Amend description for parameter "Power" in XMV Parameter List
Added MY4-AEC address to Meter List
Added clarification of [devstatus runmode] command, which is necessary to establish remote control
communication.
1.3.1, 1.3.2 Increased total number of remote controller devices which can simultaneously access the MTX
system.
3.1
Fixed some incorrect values in the "Normalized Value" column of the table, and in the note below the
table.
3.3.5
Added "setr" command, which allows relative inc/dec level control.
6
Added "value to data" tables for fader parameters.
7
Added comments in remarks column for when "setr" command is available.
7
Added "DigitalInputSensitivity" parameter for XMV
1, 3.2.2, 3.3.4 Added MRX7-D
3.3.5, 3.3.6, 6.
7, 8
1.3.3
Added "MRX7-D and Remote Control Setup List"
2, 3.2.3.
Added "NOTIFY ssrecall" command
2, 3.2.4.
Added "NOTIFY sscurrent_ex"command
2, 3.2.4.
Added "NOTIFY ssrecall_ex" command
2, 3.3.8.
Added "ssrecall_ex"command
3.1.
Amended raw value examples for 400Hz and 2kHz
3.2.2. 1-5) Amended "Detail"
3.3.4. 2-10)
3.3.4. 2-11)
3.3.5 2-13)
3.3.5 2-14)
3.3.5 2-15)
6
Fixed MTX5 parameter in "1.Input Patch"
7
Fixed Category of "INPUT CHANNEL"
7
Amended to clarify Analog Gain to "Gain"and Digital Gain to "D.Gain"
7
Fixed "Xpos" in "MATRIX"
7
Fixed "UniqueId" in "OUTPUT CHANNEL" of "SPEAKER PROCESSOR"
7
Fixed "Xpos" in "OUTPUT PORT" of "OUTPUT PORT"
7
Amended "Remarks" in "MY4-AEC"
3.2.2
Added new 'Important' comment regarding Parameter change notification raw/normalised values in
MRX7-D part
7
Fixed Remark for "Channel Name" parameter in MTX3/MTX5-D part
7
Fixed ElmNo for "ROUTER" parameter in MTX3/MTX5-D part
7
Fixed "INPUT CHANNEL LEVEL" & "INPUT CHANNEL MUTE" parameters in MTX3/MTX5-D part
7
Fixed "INPUT CHANNEL DCA" parameters in MTX3/MTX5-D part
7
Fixed "MATRIX OUTPUT MASTER" parameters in MTX3/MTX5-D part
7
Added "ZONE DCA/MUTE" parameters in MTX3/MTX5-D part
7
Fixed Remark for "EQ/GEQ Gain" parameter in MRX7-D
7
Added "Acoustic Echo Canceller" parameters in MRX7-D
7
Added "Revolabs Control" parameters in MRX7-D
7
Fixed Remark for "ChannelName" parameters in XMV series
8
Fixed Meter Name for "OUTPUT PORT OUTPUT(SLOT)" in MTX3/MTX5-D part
8
Fixed Meter Name for "Matrix Mixer" in MRX7-D part

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

4

0. Revision History
Version
V2.2.0

Date
Jun. 21, 2016

Section
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8
8

Description
Added "B/W(Q)" parameter for PEQ in MRX7-D part
Added "Paging Ducker", "Effect" and "Pitch Shift FBS" parameters in MRX7-D part
Added "B/W(Q)" parameter for Speaker Processor PEQ in MRX7-D part
Fixed Remarks for "GAIN/HPF" of "MIC/LINE INPUT MONO CH STRIP 1-8(16)" in "INPUT
CHANNEL" category in MTX3/MTX5-D part
Changed parameter name "DCA Fader 8(16) Channel" to "Fader 8(16) Channel" for "INPUT
CHANNEL LEVEL" in MTX3/MTX5-D part
Changed parameter name "DCA Fader 6 Channel" to "Fader 6 Channel" for "INPUT CHANNEL
LEVEL" in MTX3/MTX5-D part
Changed parameter name "DCA Mute 6 Channel" to "Mute 6 Channel" for "INPUT CHANNEL
MUTE" in MTX3/MTX5-D part
Changed parameter name "DCA Fader 8 Channel" to "Fader 8 Channel" for "INPUT CHANNEL
LEVEL" in MTX3/MTX5-D part
Changed parameter name "DCA Mute 8 Channel" to "Mute 8 Channel" for "INPUT CHANNEL
MUTE" in MTX3/MTX5-D part
Added "INPUT CHANNEL DCA" and "INPUT CHANNEL MUTE" categories in MTX3/MTX5-D part
Deleted duplicated "INPUT CHANNEL DCA / MUTE" parameters between "MIC/LINE INPUT MONO
CH STRIP 1-8(16)" and "LINE INPUT ST/MONO CH STRIP 1L-3R" in MTX3/MTX5-D part
Merged "ZONE DCA/MUTE" parameters into "ZONE" category in MTX3/MTX5-D part
Added "DCA Mute 8(16) Channel" for Zone in MTX3/MTX5-D part
Changed parameter name "DCA Fader 8(16) Channel" to "Fader 8(16) Channel" for "MATRIX
OUTPUT MASTER" in MTX3/MTX5-D part
Added "Paging Ducker" parameters for Dynamics in MRX7-D part
Added "Effect" parameters in MRX7-D part
Added "Notch FBS" parameters and "Pitch Shift FBS" parameters in MRX7-D part
Added "Delay Matrix" parameters for Mixer in MRX7-D part
Added "Paging Ducker" parameters for Dynamics in MRX7-D part
Added "Delay Matrix" parameters for Mixer in MRX7-D part

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

5

0. Revision History
Version
V3.0.0

Date
Feb. 24, 2017

Section
2
3.3.5
3.4.2
3.4.3 3-27)
3.4.3 3-28)
4
4
5
6
6
7

7

7
7
7

7
7
7
7
7
8
8
8
8
8
8
8

Description
Changed command category name "Preset recall processing" to "Preset processing request" in 2.
Command List
Added Notes in "Parameter setting" for "2-14) Normalized value parameter setting".
Unified term "Snapshot (preset) list" to "Preset list".
Simplified command names deleting "(for list)".
Ameneded detail of "Normal procedure"
"snapshot (preset) control" to "Snapshot or Preset"
"snapshot (preset) display" to "Preset list display"
Unified term "Snapshot (preset)" to "Preset".
Amended "1.Level Meter, Hold Meter" to "1.Level Meter, Hold Meter, GR Meter".
Changed the command number 22 and bigger number due to modification above "21.Pitch Shift
FBS"
Amended "Group(9 - 16 Channnel) " to "Group(9 - 24 Channnel)" in "23.Dugan Automixer"
Improved parameter name in MTX3/MTX5-D part :
"MIC/LINE INPUT MONO CH STRIP 1-8(16)" to "INPUT CH STRIP 1-8(16)"
"LINE INPUT ST/MONO CH STRIP 1L-3R" to "STEREO INPUT CHANNEL STIN 1L-3R"
"DIRECT INPUT MONO CH STRIP 1-8" to "DIRECT INPUT CHANNEL CH 9 - 16 ( 17 - 24 )"
"Ducking 8 Channel" to "PRIORITY DUCKER"
"Router 40(48) Input 1 Output" to "PRIORITY SOURCE"
"Router 40(48) Input 1 Output" to "ANC SOURCE"
Marged two lines for MTX3 and MTX5-D parameters into one line for simplification in MTX3/MTX5-D
part :
"STIN 1L-3R 3BAND EQ"
"GroupMaster" in "INPUT CHANNEL DCA"
"GroupMaster" in "INPUT CHANNEL DCA MUTE"
"ZONE OUT GroupMaster"
"ZONE OUT MUTE GroupMaster"
Moved "EFFECT" for siplification within MTX3/MTX5-D part.
Added "Dugan Auto Mixer" in MTX3/MTX5-D part.
Amended parameter name in MTX3/MTX5-D part :
"MixBus 26(34) Input x 8(16) Output(STEREO) -> (MONO)" to "MATRIX (ZONE OUT MONO) 26(34)
Input x 8(16) Output" for "MATRIX"
"MixBus 26(34) Input x 8(16) Output (MONO) -> (STEREO)" -> "MATRIX (ZONE OUT STEREO)
26(34) Input x 8(16) Output" for "MATRIX"
Added notes about parameters in MTX3/MTX5-D part :
"MATRIX(MONO) 26(34) Input x 8(16) Output" in "MATRIX"
"MATRIX(STEREO) 26(34) Input x 8(16) Output" in "MATRIX"
Amended parameter name "Matrix Mixer 22(30) Input 2 Output" to "Matrix Mixer 22(30) Input 4
Output" in MTX3/MTX5-D part.
Combined "2nd PRIORITY DUCKER", "1st PRIORITY DUCKER", "ANC" and "SOURCE SELECT"
for simplification in MTX3/MTX5-D part.
Added remarks for "Dugan Auto Mixer" in MRX7-D part.
Fixed remarks for "DigitalInputSensitivity" in XMV part.
Amended remarks in MTX3/MTX5-D part.
Fixed UniqueId "20004" to "20024" for "INPUT(YDIF)" in MTX3/MTX5-D part.
Added "Dugan Auto Mixer" in MTX3/MTX5-D part.
Added variation "40 OUT" , "48 OUT" and "56 OUT" for "Matrix Mixer" in MRX7-D part.
Fixed Meter Name for "Speaker Processor" in MRX7-D part.
Added meter Type "gr" for "Speaker Processor" in MRX7-D part.
Added channel number in MRX7-D part :
"Room Combiner plus Auto Mixer ( Mic 17 - 24 Channel )"
"Dugan Automixer 17 - 24 Channel"

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

6

0. Revision History
Version
V3.1.0

Date
Jun.19, 2017

Section
2,3,4,6,7,8
2.1. 1-7)
1-8)
1-10)
2.2. 2-5)
2-19)
2.3. 3-10)
3-11)
3-27)
3-28)
3-31)
2.3. 3-31)
3-32)
3.2.3
3.2.4
3.2.5
3.2.5 1-10)
3.2.6
3.3.2
3.3.2 2-5)
3.3.5 2-16)
3.3.7
3.3.8 2-21)
3.4.3 3-10)
3-11)
3.3.6 2-17)
2-18)
3.4.3 3-16)
3-18)
3-20)
3-22)
3-24)
3.4.3 3-28)
:
3-32)
3-38)
3-41)
3-42)
3.4.3 3-16)
3-31)
3-32)
3.4.3 3-28)
3.4.3 3-27)
3-28)
3-31)
3-32)
3-37)
3-38)
6
6
7
7
7
7
7
7

Description
Added Table of contents.
Rearranged format of section number and renumbering.
Modified "Notification detail" and "Request details".

Added description in Remarks.
Unified titles in command list of "2. Command List" and section names in command detail of
"3. Command Specifications"

Corrected references information in "Details:".
Added "Details:" for command options.

Added "Notes:" for command option and detail.

"Added commands "Details:".
Added command "option2" example.
Amended description in "Details:" and "Example".

Deleted "14. MY4-AEC Digtal I/O SRC" parameters in MTX3/MTX5-D part.
Rearranged tables according to the order of "7.Parameter List".
Added "PAGING","OSCILLATOR" and "PILOT TONE" parameters in MTX3/MTX5-D part.
Added "Paging" parameters in MRX7-D part.
Changed maximum value of "Utility/InputSelect" parameter in XMV part.
Added "ChUtility/InputSelect" parameter in XMV part.
Added "Note(*3)" for "Utility/InputSelect","ChUtility/InputSelect" parameters in XMV part.
Amended Block Diagram in XMV part.

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

7

1. Setup
1.1. Connection Procedure
Connection when using the NETWORK connector to perform remote control using this protocol
MTX3
Remote Controller

Ethernet

Network
Switch

Ethernet

Ethernet

Network
Switch

Ethernet

Ethernet

Network
Switch

Ethernet

MTX5-D
Remote Controller

MRX7-D
Remote Controller

* Also for XMV, EXi8 and EXo8.
XMV can be controlled with the protocol in this document without MTX3, MTX5-D or MRX7-D.
Connection when using the REMOTE connector to perform remote control using this protocol
MTX3
Remote Controller

RS-232C (Crossover cable)

MTX5-D
Remote Controller

RS-232C (Crossover cable)

MRX7-D
Remote Controller

RS-232C (Cross cable)

* XMV, EXi8 and EXo8 do not have REMOTE connectors

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

8

1. Setup

1.2. Configuring the Remote Controller
MTX3, MTX5-D and MRX7-D can be controlled from an external controller through the Ethernet (NETWORK) connector and RS-232C
(REMOTE) connector.
XMV, EXi8 and EXo8 can be controlled from an external controller through the Ethernet (NETWORK) connector.
The configuration on the remote controller side for each type of connection is shown below.
Ethernet (NETWORK connector) control
IP Address: Specify the IP address of the device you want to control.
IP Port No.: 49280
RS-232C (REMOTE connector) control
Bit Rate: The specified bit rate.
Data: 8 bits
Parity: none
Stop bit: 1 bit
Flow Control : none
RS-232C port pin assignment
Pin
1
2
3
4
5

Name
NC
RxD
TxD
DTR
GND

In/Out
In
Out
Out
-

Pin
6
7
8
9

Name
DSR
RTS
CTS
NC

In/Out
In
Out
In
-

* Pin 4 and Pin 6 are connected internally.
* Pin 7 and Pin 8 are connected internally.

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

9

1. Setup

1.3. Device Configuration
1.3.1. MTX3, MTX5-D and MRX7-D
MTX3, MTX5-D and MRX7-D can be controlled from an external controller through a NETWORK and RS-232C connector.
Up to nine remote controller devices can connect simultaneously to one MTX or MRX device, eight via the NETWORK
connector and one via the RS232 connector.
The procedure to configure the second control port of MTX3, MTX5-D and MRX7-D is shown below, this is found in MTX-MRX
Editor - System Menu- > Remote control.

(1)

(2)

(1) Select an MTX or MRX within the MTX/MRX system.
(2) Select BIT RATE of 38400 or 115200 for RS-232C control.
After selecting all the parameters, click OK to complete the procedure.
* In the case of the MTX5-D NETWORK remote control connection, either network connector (Primary or Secondary) can be
used when DANTE Daisy Chain mode is selected.
If using DANTE Redundant mode, only the Primary network connection and/or RS-232C connection can be used for remote
control.

1.3.2. XMV, EXi8 and EXo8
XMV, EXi8 and EXo8 can be controlled via an external device through a NETWORK connector.
Up to eight remote controller devices can connect simultaneously.
As remote control of XMV, EXi8 and EXo8 is performed via the NETWORK connector only, there is no requirement to configure
the port using MTX-MRX Editor for remote control.
When XMV, Exi8 and EXo8 are connected and controlled from MTX3, MTX5-D or MRX7-D, up to seven remote controller
devices can be used for these devices.

1.3.3. MRX7-D and Remote Control Setup List
Remote Parameter control for MRX7-D is managed via the Remote Control Setup List. This list must first be created in MTXMRX Editor in order to specify which Parameters can be controlled from an external remote controller. This list will be upoaded
to MRX7-D during Synchronisation.

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

10

2. Command List
2.1. Commands from a device sent to a remote controller
No.
1-1 Device status change
notification
1-2
1-3
1-4
1-5 Parameter change
notification
1-6
1-7 Meter information
notification
1-8 Preset change notification
1-9
1-10 Snapshot change
1-11 notification
1-12 Event processing change
notification
1-13

Notification details
Device run mode notification

Reply from device
NOTIFY devstatus runmode ...

Device error status notification
Current Fs (sampling frequency) setting
notification
Current word clock status notification
Parameter change notification raw value
Parameter change notification normalized value
Scheduler on/off change notification
Meter information notification

NOTIFY devstatus error ...
NOTIFY devstatus fs ...

Current Preset number change notification
Preset recall start notification
Current Snapshot number change notification
Snapshot recall start notification
Media insertion notification

NOTIFY sscurrent ...
NOTIFY ssrecall ...
NOTIFY sscurrent_ex ...
NOTIFY ssrecall_ex ...
NOTIFY event MTX:Media ...

NOTIFY devstatus lockstatus ...
NOTIFY set ...
NOTIFY setn ...
NOTIFY set(setn) MTX:EvntScd_On ...
NOTIFY mtr ...

Time synchronization notification  NOTIFY event MTX:AbsoluteTime ...

1-14

Time synchronization notification  NOTIFY event MTX:SetAbsoluteTime…

1-15

DST enable change notification

NOTIFY event MTX:DSTSetEnable…

1-16

DST offset time change notification

NOTIFY event MTX:DSTSetOffset…

1-17

DST start time change notification

NOTIFY event MTX:DSTSetStartTime…

1-18

DST end time change notification

NOTIFY event MTX:DSTSetEndTime…

1-19

DST start/end day change notification (day/week) NOTIFY event MTX:DSTSetDayWeek…

1-20

DST start/end day change notification (day)

NOTIFY event MTX:DSTSetDay…

1-21

Song play mode notification

1-22

Play, stop, and other transport operation
notification
Playback song notification

NOTIFY event MTX:
AudioPlayerSetPlayMode ...
NOTIFY event MTX:
AudioPlayerTransport ...
NOTIFY event MTX:
AudioPlayerSetCurrentSong ...
NOTIFY event MTX:
SynchronizationSetStatus ...

1-23
1-24

MTX Editor synchronization processing
notification

Remarks
"emergency" is invalid on the XMV, EXi8
and EXo8.

This command is available only for MRX7-D
This command is available only for MRX7-D
This command is invalid on the XMV, EXi8
and EXo8.
This command is invalid on the EXi8 and
EXo8.
This command is invalid on the EXi8 and
EXo8.
This command is invalid on the XMV, EXi8
and EXo8.
This command is invalid on the XMV, EXi8
and EXo8.
This command is invalid on the XMV, EXi8
and EXo8.
This command is invalid on the XMV, EXi8
and EXo8.
This command is invalid on the XMV, EXi8
and EXo8.
This command is invalid on the XMV, EXi8
and EXo8.
This command is invalid on the XMV, EXi8
and EXo8.
This command is invalid on the XMV, EXi8
and EXo8.
This command is invalid on the XMV, EXi8
and EXo8.
This command is invalid on the XMV, EXi8
and EXo8.

2.2. Commands for controlling a device
No.
2-1 Device status query

Request details
Device run mode query

Command string
devstatus runmode

2-2
2-3
2-4
2-5 Device run mode change

Device error status query
Current Fs (sampling frequency) status query
Current word clock status query
Device run mode change

2-6 MTX external control
protocol run mode setting
2-7
2-8
2-9
2-10 Parameter query
2-11
2-12

Result and change notification character
encoding setting
Value notification mode setting
Normalization resolution setting
Keepalive activation setting
Raw value parameter query
Normalized value parameter query
Scheduler status notification

devstatus error
devstatus fs
devstatus lockstatus
devmode normal
devmode emergency
scpmode encoding ...

2-13 Parameter setting
2-14
2-15

set ...
setn ...
setr…

2-16

Raw value parameter setting
Normalized value parameter setting (*)
Relative value parameter setting
(INC/DEC level control)
Scheduler setting

2-17 Meter control
2-18
2-19 Preset processing

Transmission request
Stop request
Preset current number query processing

mtrstart ...
mtrstop ...
sscurrent ...

2-20

Preset recall processing

ssrecall ...

2-21 Snapshot processing

Snapshot recall processing

ssrecall_ex ...

scpmode valuetype ...
scpmode resolution ...
scpmode keepalive ...
get ...
getn ...
get(getn,gett) MTX:EvntScd_On ...

set(setn,sett) MTX:EvntScd_On ...

Remarks
"emergency" is invalid on the XMV, EXi8
and EXo8.

"emergency" is invalid on the XMV, EXi8
and EXo8.

This command is invalid on the XMV, EXi8
and EXo8.

This command is invalid on the XMV, EXi8
and EXo8.

This command is invalid on the XMV, EXi8
and EXo8.
This command is invalid on the XMV, EXi8
and EXo8.
This command is available only for MRX7-D

* When value is set "1023" (default:1000), control resolution becomes same as "Raw value" command.
See "6.1. Fader parameter" for the "Nomalised value" vs "Raw value" when the value is set "1023"

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

11

2. Command List

2.3. Extended commands
No.
3-1 Product information
3-2 query request
3-3
3-4
3-5
3-6
3-7
3-8 Preset processing
request
3-9
3-10 Event processing
request
3-11
3-12
3-13
3-14
3-15
3-16
3-17
3-18
3-19
3-20
3-21
3-22
3-23
3-24
3-25
3-26
3-27
3-28
3-29
3-30
3-31
3-32
3-33
3-34
3-35
3-36
3-37
3-38
3-39
3-40
3-41
3-42
3-43

Request details
MTX external control protocol version query
Parameter set version query
Firmware version query
Product name query
Serial number query
Device ID query
Device name query
Number of Preset lists

Command string
devinfo protocolver ...
devinfo paramsetver ...
devinfo version ...
devinfo productname ...
devinfo serialno ...
devinfo deviceid ...
devinfo devicename ...
ssnum ...

Remarks

This command is invalid on the XMV, EXi8
and EXo8.
Nth preset information
ssinfo ...
This command is invalid on the XMV, EXi8
and EXo8.
Time synchronization 
event MTX:AbsoluteTime ...
This command is invalid on the EXi8 and
EXo8.
Time synchronization 
event MTX:SetAbsoluteTime ...
This command is invalid on the EXi8 and
EXo8.
Time query
event MTX:GetAbsoluteTime ...
This command is invalid on the EXi8 and
EXo8.
DST enable/disable setting
event MTX:DSTSetEnable…
This command is invalid on the XMV, EXi8
and EXo8.
DST enable/disable query
event MTX:DSTGetEnable…
This command is invalid on the XMV, EXi8
and EXo8.
DST status query
event MTX:DSTGetStatus…
This command is invalid on the XMV, EXi8
and EXo8.
DST offset time setting
event MTX:DSTSetOffset…
This command is invalid on the XMV, EXi8
and EXo8.
DST offset time query
event MTX:DSTGetOffset…
This command is invalid on the XMV, EXi8
and EXo8.
DST start time setting
event MTX:DSTSetStartTime…
This command is invalid on the XMV, EXi8
and EXo8.
DST start time query
event MTX:DSTGetStartTime…
This command is invalid on the XMV, EXi8
and EXo8.
DST end time setting
event MTX:DSTSetEndTime…
This command is invalid on the XMV, EXi8
and EXo8.
DST end time query
event MTX:DSTGetEndTime…
This command is invalid on the XMV, EXi8
and EXo8.
DST start/end day setting (day/week)
event MTX:DSTSetDayWeek…
This command is invalid on the XMV, EXi8
and EXo8.
DST start/end day query (day/week)
event MTX:DSTGetDayWeek…
This command is invalid on the XMV, EXi8
and EXo8.
DST start/end day setting (day)
event MTX:DSTSetDay…
This command is invalid on the XMV, EXi8
and EXo8.
DST start/end day query (day)
event MTX:DSTGetDay…
This command is invalid on the XMV, EXi8
and EXo8.
DST start/end day setting query
event MTX:DSTGetDaySetting…
This command is invalid on the XMV, EXi8
and EXo8.
Current folder information query
event MTX:AudioPlayerGetCurrentDir ...
This command is invalid on the XMV, EXi8
and EXo8.
Current folder move query
event MTX:AudioPlayerSetCurrentDir ...
This command is invalid on the XMV, EXi8
and EXo8.
Folder name query
event MTX:AudioPlayerGetDirName ...
This command is invalid on the XMV, EXi8
and EXo8.
File name query
event MTX:AudioPlayerGetFileName ...
This command is invalid on the XMV, EXi8
and EXo8.
Folder name list query
event MTX:AudioPlayerGetDirNameList ... This command is invalid on the XMV, EXi8
and EXo8.
File name list query
event MTX:AudioPlayerGetFileNameList ... This command is invalid on the XMV, EXi8
and EXo8.
Song play mode query
event MTX:AudioPlayerGetPlayMode ...
This command is invalid on the XMV, EXi8
and EXo8.
Song play mode setting
event MTX:AudioPlayerSetPlayMode ...
This command is invalid on the XMV, EXi8
and EXo8.
Song playback status query
event MTX:AudioPlayerGetStatus ...
This command is invalid on the XMV, EXi8
and EXo8.
Play, stop, and other transport operation
event MTX:AudioPlayerTransport ...
This command is invalid on the XMV, EXi8
and EXo8.
Currently playing or selected song
event MTX:AudioPlayerGetCurrentSong ... This command is invalid on the XMV, EXi8
information query
and EXo8.
Playback song designation
event MTX:AudioPlayerSetCurrentSong ... This command is invalid on the XMV, EXi8
and EXo8.
MTX Editor synchronization processing query event MTX:SynchronizationGetStatus ...
This command is invalid on the XMV, EXi8
and EXo8.
Number of alert event log query
event MTX:EventLogGetLogNumber…
Alert event log query
event MTX:EventLogGetLog…
Query for alert event log as list
event MTX:EventLogGetLogList…
Clear alert event log
event MTX:EventLogClear…

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

12

3. Command Specifications
3.1. Basic Command Specifications
Below is the syntax of commands exchanged between a device and remote controller.
   . . .  
- Each command must end with LF (0x0A).
- LF (0x0A) code can be sent as heart-beat command.
Refer to section 3.3.3: "2-9) Keepalive activation setting" for description of run mode setting, which describes the use of this heart-beat
command.
- Character type letter(s) in command line must be bracketed by double quotations.
When double quotation itself needs to be included in command line, use "escape character" as shown below.
Backslash works as an escape character to express following one character for double quotation and backslash.
Syntax
\\
\"

Meaning
\
"

Description
backslash
double quotation

- At least one space is necessary between a command name and an option and between options.
- Commands must be expressed using ASCII characters. Other characters are not allowed.
- Option strings that express parameter values are shown below.
Value
-Infinity
-18dB
-6.5dB
0dB
10dB
2kHz
400Hz
Pan L 63
Pan Center
Pan R 63

Displayed string
"-INFINITY"
"-18.00"
"-6.50"
"0.00"
"10.00"
"2.00k"
"400"
"L63"
"C"
"R63"

ON

"ON"

OFF

"OFF"

INVERTED
NORMAL

"INVERTED"
"NORMAL"

Raw value
-13801
-1800
-650
0
1000
2000000
400000
-63
0
+63
0
1
0
1
1
0

Normalized value
0
453
677
804
1000
667
435
0
500
1000
500
1000
0
1000
1000
0

* For other parameters, see section 6, "Parameter Value Details," provided later.
* Normalized value is a converted value when minimum value of the parameter is as 0 and maximum value of the parameter is as 1000*1.
Example: -inf as minimum mapped 0, 10dB as maximum mapped 1000, 0dB mapped 804 for level parameter.
*1: This value is set by 2-8) Normalization resolution setting, default resolution is 1000.

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

13

3. Command Specifications

3.2. Commands a Device Sends to a Remote Controller
3.2.1. Device status change notification
1-1) Device run mode notification
Command
NOTIFY devstatus

Example:

Option 1
runmode

Option 2
"emergency"
"update"
"normal"

Description
Emergency run mode
Update mode
Normal run mode

Notification: NOTIFY devstatus runmode "normal"
Meaning: The run mode was changed to normal mode.

1-2) Device error status notification
Command
NOTIFY devstatus

Option 1
error

Option 2
"flt/xxxx"
"err/xxxx"
"wrn/xxxx"

Description
Alert fault information
Alert error information
Alert warning information

"flt/message// xnnn onf (sssss) ID-xxx 2012/12/31 23:59:59"
"err/message// xnnn onf (sssss) ID-xxx 2012/12/31 23:59:59"
"wrn/message// xnnn onf (sssss) ID-xxx 2012/12/31 23:59:59"
The first three characters indicate the alert type.
Alert message (The section from "/" to "//" after the alert type is the message data.)
. . . up to 32 characters (ascii characters)
Alert number (panel display number)
. . . 2 or 3 digit hexadecimal notation (The x at the front indicates hexadecimal notation.)
Alert on/off
...P
 ersistent alerts turn on when an alert condition occurs and turn off when they are cleared.
Single-shot alerts turn on while an alert condition is true.
sssss = Identical alert count (a counter that indicates the number of identical alerts, normally set to 1)
		 . . . Decimal notation
xxx = UNIT ID number . . . 3-digit hexadecimal
Date
Time
Details:

"flt/xxxx" =
"err/xxxx" =
"wrn/xxxx" =
		
message =
		
nnn =
		
onf =
		

Example:

Notification: NOTIFY devstatus error "err/DCP[0] communication error// x53 on (1) ID-001 2013/1/22 11:38:23"
Meaning: Error alert 53 occurred.

1-3) Current Fs (sampling frequency) setting notification
Command
NOTIFY devstatus

Example:

Option 1
fs

Option 2
"unknown"
44.1kHz
"48kHz"

Description
Fs undefined
44.1kHz
48kHz

Notification: NOTIFY devstatus fs "44.1kHz"
Meaning: Fs was changed to 44.1 kHz.

1-4) Current word clock status notification
Command
NOTIFY devstatus
Example:

Option 1
lockstatus

Option 2
"unlock"
"lock"

Description
Unlock
Lock

Notification: NOTIFY devstatus lockstatus "lock"
Meaning: Word clock was locked.

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

14

3. Command Specifications
3.2.2. Parameter change notification
1-5) Parameter change notification raw value
Parameter change notification normalized value
MTX3,MTX5-D,XMV,EXi8,EXo8
Command
NOTIFY set

Option 1
Option 2 Option 3 Option 4 Option 5
MTX:mem_MemNo/UniqueId/ElmNo/Xpos/Ypos/ 0
0
"(value)" "(string)"
PrmNo/IndexNo
NOTIFY setn MTX:mem_MemNo/UniqueId/ElmNo/Xpos/Ypos/ 0
0
"(value)" "(string)"
PrmNo/IndexNo
Details:

Example:

MemNo =
UniqueId =
ElmNo =
Xpos =
Ypos =
PrmNo =
IndexNo =
"(value)" =
"(string)" =

Description
Parameter change
raw value
Parameter change
normalized value

See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
See section 3.1, "Basic Command Specifications," or section 7, "Parameter List."
See section 3.1, "Basic Command Specifications," or section 7, "Parameter List."

Notification: NOTIFY set MTX:mem_512/60000/0/0/0/0/0 0 0 -7760 "-77.60"
Meaning: DCA Fader 1ch level was changed to "-77.60."

MRX7-D
Command
Option 1
NOTIFY set MTX:Index_IndexNo
NOTIFY setn MTX:Index_IndexNo
Details:

Option 2 Option 3 Option 4 Option 5
Description
0
0
"(value)" "(string)" Parameter change raw value
0
0
"(value)" "(string)" Parameter change normalized value

IndexNo = Index number assigned in Remote Control Setup List
"(value)" = See section 3.1, "Basic Command Specifications," or section 7, "Parameter List."
"(string)" = See section 3.1, "Basic Command Specifications," or section 7, "Parameter List."

Example:
Notification: NOTIFY set MTX:Index_1 0 0 -7760 "-77.60"
		 (V2.02 or earlier NOTIFY set MTX:Index_001 0 0 -7760 "-77.60")
Meaning: Level of the parameter assigned to Index 1 in Remote Control List was changed to "-77.60".
Important:

If a parameter is assigned to multiple Index numbers in the Remote Control Setup List, Notification is only
provided to the lowest assigned Index number.

1-6) Scheduler on/off change notification
Command
NOTIFY set(setn)

Option 1
Option 2
MTX:EvntScd_On 0

Option 3
0

Option 4
1
0

Option 5
"1"
"0"

Description
Scheduler on
Scheduler off

* For setn, option 4 is expressed using a normalized value.
Example:

Notification: NOTIFY set MTX:EvntScd_On 0 0 1 "1"
Meaning: The scheduler was turned on.

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

15

3. Command Specifications
3.2.3. Meter information notification
1-7) Meter information notification
MTX3,MTX5-D,XMV,EXi8,EXo8
Command
NOTIFY mtr
Details:

Option 1
MTX:mtr_MemNo/UniqueId/meter

Option 2
level
gr

Option 3
(meter)

Description
Level meter value
gr meter value

MemNo = See section 8, "Meters."
UniqueId = See section 8, "Meters."
(meter) = See section 5, "Meter Values."

Example:
Notification: NOTIFY mtr MTX:mtr_512/20020/meter level 71 71 71 71 71 71 69 68
		 * The meter value is expressed using a 2-digit hexadecimal.
Meaning: Output levels for ch1 to 8 Level are sent.
MRX7-D
Command
NOTIFY mtr

Details:

Option 1
MTX:Index_IndexNo

Option 2
level
gr
hold

Option 3
(meter)

Description
Level meter value
gr meter value
Hold meter value

IndexNo = Index number assigned in Remote Control Setup List
(meter) = See section 5, "Meter Values."

Example:
Notification:
		
		
Meaning:

NOTIFY mtr MTX:Index_2 level 71 71 71 71 71 71 69 68
(V2.02 or earlier NOTIFY mtr MTX:Index_002 level 71 71 71 71 71 71 69 68)
* The meter value is expressed using a 2-digit hexadecimal.
Output levels for Ch1 to 8 which are assigned to Index 2 in Remote Control list are sent.

3.2.4. Preset change notification
1-8) Current Preset number change notification
Command
NOTIFY sscurrent
Details:
Example:

Option 1
(index)

Description
Current preset number change notification

(index) = Current preset index number
Notification: NOTIFY sscurrent 10
Meaning: Current preset was changed to index 10 (preset 10).

1-9) Preset recall start notification
Command
NOTIFY ssrecall
Details:
Example:

Option 1
(index)

Description
Preset recall process started

(index) = Preset index number
Notification: NOTIFY ssrecall 10
Meaning: Preset recall process for Index 10 preset started.

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

16

3. Command Specifications
3.2.5. Snapshot change notification
1-10) Current Snapshot number change notification
Command
NOTIFY sscurrent_ex
Details:
Example:

Option 1
list

Option 2
(index)

Description
Current preset number change notification

(index) = Index number for Snapshot assiged in Remote Control Setup List
Notification: NOTIFY sscurrent_ex list 5
Meaning: Snapshot recall occurred for the Snapshot assigned to index 5 in Remote Control Setup List

1-11) Snapshot recall start notification
Command
NOTIFY ssrecall_ex
Details:
Example:

Option 1
list

Option 2
(index)

Description
Snapshot recall start notification

(index) = Index number for Snapshot assiged in Remote Control Setup List
Notification: NOTIFY ssrecall_ex list 5
Meaning: Snapshot recall process for Index 5 started.

3.2.6. Event processing change notification
1-12) Media insertion notification
Command
NOTIFY event

Option 1
MTX:Media

Option 2
"sdcard=inserted"
"sdcard=extracted"

Description
An SD memory card was inserted.
An SD memory card was removed.

Example:

Notification: NOTIFY event MTX:Media "sdcard=inserted"
Meaning: An SD memory card was inserted into an SD memory card slot and was detected normally.
		 * SD Card should not be removed when the MTX is powered on.
1-13) Time synchronization notification 
Command
NOTIFY event

Option 1
MTX:AbsoluteTime

Details:

Year (Gregorian)
Month (1 to 12)
Day (1 to 31)
Hour (0 to 23)
Minute (0 to 59)
Second (0 to 59)
* DST (Daylight Saving Time) is not accounted for.

yyyy =
mm =
dd =
hh =
mm =
ss =
		
Example:

Note:

Option 2
"yyyy/mm/dd hh:mm:ss"

Description
Time synchronization notification

Notification: NOTIFY event MTX:AbsoluteTime "2013/1/25 10:58:19"
Meaning: The time was set to January 25, 2013, 10 hours 58 minutes 19 seconds.
This command’s option1 string "MTX:AbsoluteTime" is retained to keep compatibility with previous programming using
the previous protocol. The command’s function is identical to the new format shown below.
Device sends both format commands when time is set in order to keep compatibility with program which done for old
format in past.
Ignore this command and process new format command in new program.

1-14) Time synchronization notification 
Command
NOTIFY event

Option 1
MTX:SetAbsoluteTime

Details:

Year (Gregorian)
Month (1 to 12)
Day (1 to 31)
Hour (0 to 23)
Minute (0 to 59)
Second (0 to 59)
* DST (Daylight Saving Time) is not accounted for.

yyyy =
mm =
dd =
hh =
mm =
ss =
		
Example:

Option 2
"yyyy/mm/dd hh:mm:ss"

Description
Time synchronization notification

Notification: NOTIFY event MTX:SetAbsoluteTime "2013/1/25 10:58:19"
Meaning: The time was set to January 25, 2013, 10 hours 58 minutes 19 seconds

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

17

3. Command Specifications
1-15) DST enable change notification
Command
NOTIFY event
Example:

Option 1
MTX:DSTSetEnable

Option 2
"enable"
"disable"

Description
DST enable
DST disable

Notification: NOTIFY event MTX:DSTSetEnable "enable"
Meaning: DST was enabled

1-16) DST offset time change notification
Command
NOTIFY event
Details:

Example:

Option 1
MTX:DSTSetOffset

Option 2
"offset=hh:mm"

Description
DST offset time change notification

hh = Hour (0 to 2)
mm = Minute (0 to 59)
Notification: NOTIFY event MTX:DSTSetOffset "01:00"
Meaning: DST offset was set one hour

1-17) DST start time change notification
Command
NOTIFY event
Details:

Example:

Option 1
MTX:DSTSetStartTime

Option 2
"time=hh:mm"

Description
DST start time change notification

hh = Hour (0 to 23)
mm = Minute (0 to 59)
Notification: NOTIFY event MTX:DSTSetStartTime "time=12:00"
Meaning: DST start time was set to 12:00

1-18) DST end time change notification
Command
NOTIFY event

Option 1
MTX:DSTSetEndTime

Details:

hh = Hour (0 to 23)
mm = Minute (0 to 59)

Example:

Option 2
"time=hh:mm"

Description
DST end time change notification

Notification: NOTIFY event MTX:DSTSetEndTime "time=12:00"
Meaning: DST end time was set to 12:00

1-19) DST start/end day change notification (day/week)
Command
NOTIFY event
Details:

Option 1
MTX:DSTSetDayWeek
xxxx =
yyyy =
zzzz =
uuuu =
vvvv =
wwww =

Option 2
Description
"s_weekindex=xxxx|s_day=yyyy|s_month=zzzz|
DST start/end day change
e_weekindex=uuuu|e_day=vvvv|e_month=wwww" notification (day/week)

Start week (First, Second, Third, Fourth, Fifth, Last)
Start day (Sun, Mon, Tue, Wed, Thu, Fri, Sat)
Start month (Jan, Feb, Mar, Apr, May, Jun, Jul, Aug, Sep, Oct, Nov, Dec)
End week (First, Second, Third, Fourth, Fifth, Last)
End day (Sun, Mon, Tue, Wed, Thu, Fri, Sat)
End month (Jan, Feb, Mar, Apr, May, Jun, Jul, Aug, Sep, Oct, Nov, Dec)

Example:
Notification: NOTIFY event MTX:DSTSetDayWeek "s_weekindex=Last|s_day=Sun|s_month=Mar|
		 e_weekindex=Last|e_day=Sun|e_month=Oct"
Meaning: DST start/end days were set as from last Sunday in March to last Sunday in October

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

18

3. Command Specifications
1-20) DST start/end day change notification (day)
Command
NOTIFY event
Details:

Example:

Option 1
MTX:DSTSetDay
xxxx =
yyyy =
zzzz =
wwww =

Option 2
"s_month=xxxx|s_date=yyyy|e_month=zzzz|
e_date=wwww"

Description
DST start/end day change
notification (day)

Start month (Jan, Feb, Mar, Apr, May, Jun, Jul, Aug, Sep, Oct, Nov, Dec)
Start day (1 ~ 31)
End month (Jan, Feb, Mar, Apr, May, Jun, Jul, Aug, Sep, Oct, Nov, Dec)
End day (1 ~ 31)

Notification: NOTIFY event MTX:DSTSetDay "s_month=Mar|s_date=10|e_month=Nov|e_day=3"
Meaning: DST start day was set to March 10th and DST end day was set to Novenber 3rd

1-21) Song play mode notification
Command
NOTIFY event

Example:

Option 1
MTX:AudioPlayerSetPlayMode

Option 2
"playmode=one"
"playmode=repeat one"
"playmode=all"
"playmode=repeat all"
"playmode=shuffle"

Description
One song play mode
One song repeat
All song play
All songs repeat
Shuffle repeat

Notification: NOTIFY event MTX:AudioPlayerSetPlayMode "playmode=repeat one"
Meaning: The play mode was changed to one song repeat.

1-22) Play, stop, and other transport operation notification
Command
NOTIFY event

Example:

Option 1
MTX:AudioPlayerTransport

Option 2
"operation=stop"
"operation=play"
"operation=pause"

Description
Stop
Play
Pause

Notification: NOTIFY event MTX:AudioPlayerTransport "operation=stop"
Meaning: Playback was paused.

1-23) Playback song notification
Command
NOTIFY event
Details:

Option 1
MTX:AudioPlayerSetCurrentSong
xxxx =
yyyy =
zzzz =
wwww =

Example:
Notification:
		
Meaning:
		
		
Note:

Option 2
Description
"dirpath=xxxx|dirname=yyyy|fileindex= Playback song designation
zzzz|filename=wwww"

Directory path (index expression)
Directory name (name of the folder)
File index
File name
NOTIFY event MTX:AudioPlayerSetCurrentSong
"dirpath=0/1|dirname=Folder #1|fileindex=2|filename=xxxx.mp3"
The playback song was set to index number 1 "xxxx.mp3" in the "Folder #1" folder of 0/1
(index expression).
* "0/1" expresses the root folder number/sub folder number (the root folder number is always fixed at 0).

The character encoding for directory and file names conforms to the setting specified by the scpmode encoding
command.

1-24) MTX Editor synchronization processing notification
Command
NOTIFY event
Example:

Note:

Option 1
MTX:SynchronizationSetStatus

Option 2
"active"
"inactive"

Description
Synchronization start
Synchronization end

Notification: NOTIFY event MTX:SynchronizationSetStatus "active"
Meaning: Synchronization processing was started between MTX and MTX Editor.
When this notification is received, because the internal MTX settings may have changed significantly, we recommend
that you verify the connection by querying relevant parameters.

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

19

3. Command Specifications

3.3. Commands for controlling a device
3.3.1. Device status query
2-1) Device run mode query
Command

Option 1

devstatus

runmode

Description
Queries the run mode

Response
Response string
OK devstatus runmode "emergency"
OK devstatus runmode "update"
OK devstatus runmode "normal"
Example:

Command:
Response:
Meaning:
		
Note:

Description
Emergency run mode
Update mode
Normal run mode

devstatus runmode
OK devstatus runmode "normal"
Query the run mode.
The device is currently in normal run mode.

After device responds with -OK devstatus runmode "normal"-, device starts to send commands.
In order to establish remote control communication, the external controller must send [devstatus runmode] command
to the device and await response. When the device responds as [OK devstatus runmode "normal"], the device is ready
to receive commands.

2-2) Device error status query
Command
devstatus

Option 1
error

Description
Queries the error status

Response
Response string
OK devstatus error "none"
OK devstatus error "flt/xxxx"
OK devstatus error "err/xxxx"
OK devstatus error "wrn/xxxx"

Description
No alerts
fault alert
error alert
warning alert

"flt/message// xnnn onf (sssss) ID-xxx 2012/12/31 23:59:59"
"err/message// xnnn onf (sssss) ID-xxx 2012/12/31 23:59:59"
"wrn/message// xnnn onf (sssss) ID-xxx 2012/12/31 23:59:59"
The first three characters indicate the alert type.
Alert message (The section from "/" to "//" after the alert type is the message data.)
. . . up to 32 characters (ascii characters)
Alert number (panel display number)
. . . 2 or 3 digit hexadecimal notation (The x at the front indicates hexadecimal notation.)
Alert on/off
...P
 ersistent alerts turn on when an alert condition occurs and turn off when they are cleared.
Single-shot alerts turn on while an alert condition is true.
sssss = Identical alert count (a counter that indicates the number of identical alerts, normally set to 1)
		 . . . Decimal notation
xxx = UNIT ID number . . . 3- digit hexadecimal
Date
Time
Details:

"flt/ xxxx" =
"err/ xxxx" =
"wrn/ xxxx" =
		
message =
		
nnn =
		
onf =
		

Example:

Command:
Response:
Meaning:
		

devstatus error
OK devstatus error "err/DCP[0] communication error// x53 on (1) ID-001 2013/1/22 11:38:23"
Query the alert status.
Error alert 53 is occurring.

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

20

3. Command Specifications
2-3) Current Fs (sampling frequency) status query
Command

Option 1

devstatus

fs

Description
Queries Fs

Response
Response string
OK devstatus fs "unknown"
OK devstatus fs "44.1kHz"
OK devstatus fs "48kHz"
Example:

Command:
Response:
Meaning:
		

Description
Fs undefined
44.1kHz
48kHz

devstatus fs
OK devstatus fs "44.1kHz"
Query Fs.
The current Fs is 44.1 kHz.

2-4) Current word clock status query
Command

Option 1

devstatus

lockstatus

Description
Queries the word clock lock status

Response
Response string
OK devstatus lockstatus "unlock"
OK devstatus lockstatus "lock"
Example:

Command:
Response:
Meaning:
		

Description
Unlock
Lock

devstatus lockstatus
OK devstatus lockstatus "lock"
Query the word clock lock status.
Locked

3.3.2. Device run mode change
2-5) Device run mode change
Command
devmode

Option 1
normal
emergency

Description
Sets the run mode to normal
Sets the run mode to emergency

Response
Response string
OK devmode normal
OK devmode emergency
Example:

Command:
Response:
Meaning:
		

Description
Normal run mode change complete
Emergency run mode change complete

devmode emergency
OK devmode emergency
Change to emergency mode.
Run mode was changed to emergency.

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

21

3. Command Specifications
3.3.3. MTX external control protocol run mode setting
2-6) Result and change notification character encoding setting
Command
scpmode

Option 1
encoding

Option 2
ascii
utf8

Description
ASCII encoding mode (default setting)
UTF-8 encoding mode

Response
Response string
OK scpmode encoding ascii
OK scpmode encoding utf8
Example:

Command:
Response:
Meaning:
		

Description
ASCII encoding mode change complete
UTF-8 encoding mode change complete

scpmode encoding utf8
OK scpmode encoding utf8
Change the result and change notification encoding code to UTF-8.
The encoding mode was changed to UTF-8.

2-7) Value notification mode setting
Command
scpmode

Option 1
valuetype

Option 2
raw
normalized

Description
Raw value mode (default setting)
Normalized value mode

Response
Response string
OK scpmode valuetype raw
OK scpmode valuetype normalized
Example:

Command:
Response:
Meaning:
		

Description
Raw value mode change complete
Normalized value mode change complete

scpmode valuetype normalized
OK scpmode valuetype normalized
Change parameter change notifications to normalized value mode.
Parameter change notifications were changed to normalized value mode.

2-8) Normalization resolution setting
Command
scpmode
Details:

Option 1
resolution

Option 2
(res)

Description
Resolution for normalized value notifications
(default setting = 1000)

(res) = Resolution for normalized values

Response
Response string
OK scpmode resolution xxxx
Details:
Example:

xxxx = Specified resolution

Command:
Response:
Meaning:
		

Description
The resolution for normalized value notifications
* Specified resolution should be more than 100.

scpmode resolution 128
OK scpmode resolution 128
Set the resolution of normalized values for setn commands to 128.
The resolution of normalized values for setn commands was set to 128.

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

22

3. Command Specifications
2-9) Keepalive activation setting
Command
scpmode

Option 1
keepalive

Option 2
(interval)

Details:
(interval) = Timeout value (msec)
					

Description
Maximum interval for a client to send some kind of message,
including heart beats (default setting = disabled)

* Timeout value should be more than 1000.
* The actual timeout value will be increased by 1 second.

Response
Response string
OK scpmode keepalive xxxx
Details:
Example:

xxxx = The specified timeout value (msec)

Command:
Response:
Meaning:
		
Note:

Description
Keepalive activated notification

scpmode keepalive 2000
OK scpmode keepalive 2000
Set the timeout value to 2000 msec (2 seconds).
The timeout value was set to 2000 msec (2 seconds).

When unexpected disconnection happens, remote controller can’t finish communication with closing process.
In such case, device has to keep status "connected" and remote controller can’t establish new connection after that.
In order to prevent the situation above, device watches keepalive command if connection with remote controller is still
alive.
If device doesn’t receive keepalive command within timeout value which is set by this command, device terminates
connection by itself.
After the Keepalive activation command has been activated, the Remote controller must send any command or
LF(0x0A) code as a heart beat to the device within the timeout value.

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

23

3. Command Specifications
3.3.4. Parameter query
2-10) Raw value parameter query
MTX3,MTX5-D,XMV,EXi8,EXo8
Command
get
Details:

Option 1
MTX:mem_MemNo/UniqueId/ElmNo/Xpos/
Ypos/PrmNo/IndexNo
MemNo =
UniqueId =
ElmNo =
Xpos =
Ypos =
PrmNo =
IndexNo =

Option 2
0

Option 3
0

Description
Raw value parameter query
request

See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."

Response
Response string
OK get MTX:mem_MemNo/UniqueId/ElmNo/Xpos/Ypos/
PrmNo/IndexNo 0 0 (value)
Details:

MemNo =
UniqueId =
ElmNo =
Xpos =
Ypos =
PrmNo =
IndexNo =
(value) =

Example:

Command:
Response:
Meaning:
		

Description
Raw value parameter query response

See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
See section 3.1, "Basic Command Specifications," or section 7, "Parameter List."
get MTX:mem_512/60000/0/0/0/0/0 0 0
OK get MTX:mem_512/60000/0/0/0/0/0 0 0 -7760
Query the 1ch level of the DCA fader with raw values.
The 1ch level of the DCA fader is -77.60.

MRX7-D
Command
get

Option 1
MTX:Index_IndexNo

Option 2

Details:

IndexNo = Index number assigned in Remote Control Setup List

0

Option 3
0

Description
Raw value parameter query request

Response
Response string
OK get MTX:Index_IndexNo 0 0 (value)
Details:

Example:

Description
Raw value parameter query response

IndexNo = Index number assigned in Remote Control Setup List
"(value)" = See section 3.1, "Basic Command Specifications," or section 7, "Parameter List."

Command:
Response:
		
Meaning:
		

get MTX:Index_1 0 0
OK get MTX:Index_1 0 0 -7760
(V2.02 or earlier OK get MTX:Index_001 0 0 -7760)
Query level of the parameter assigned to Index 1 in Remote Control Setup List using raw values.
Level of the Parameter that is assigned to Index 1 in Remote Control Setup List is -77.60.

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

24

3. Command Specifications
2-11) Normalized value parameter query
MTX3,MTX5-D,XMV,EXi8,EXo8
Command
getn
Details:

Option 1
MTX:mem_MemNo/UniqueId/ElmNo/Xpos/
Ypos/PrmNo/IndexNo
MemNo =
UniqueId =
ElmNo =
Xpos =
Ypos =
PrmNo =
IndexNo =

Option 2
0

Option 3
0

Description
Normalized value parameter
query request

See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."

Response
Response string
OK getn MTX:mem_MemNo/UniqueId/ElmNo/Xpos/Ypos/
PrmNo/IndexNo 0 0 (value)
Details:

MemNo =
UniqueId =
ElmNo =
Xpos =
Ypos =
PrmNo =
IndexNo =
(value) =

Example:

Command:
Response:
Meaning:
		

Description
Normalized value parameter query response

See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
See section 3.1, "Basic Command Specifications," or section 7, "Parameter List."
getn MTX:mem_512/60000/0/0/0/0/0 0 0
OK getn MTX:mem_512/60000/0/0/0/0/0 0 0 408
Query the 1ch level of the DCA fader with normalized values.
The 1ch level of the DCA fader is 408.

MRX7-D
Command
getn

Option 1
MTX:Index_IndexNo

Option 2

Details:

IndexNo = Index number assigned in Remote Control Setup List

0

Option 3
0

Description
Normalized value parameter query request

Response
Response string
OK getn MTX:Index_IndexNo 0 0 (value)
Details:

Description
Normalized value parameter query response

IndexNo = Index number assigned in Remote Control Setup List
"(value)" = See section 3.1, "Basic Command Specifications," or section 7, "Parameter List."

Example:

Command:
Response:
		
Meaning:
		

getn MTX:Index_1 0 0
OK getn MTX:Index_1 0 0 408
(V2.02 or earlier OK getn MTX:Index_001 0 0 408)
Query level of a parameter assigned to Index 1 in Remote Control Setup List using normalized
values. Level of the parameter which is assigned to Index 1 in Remote Control Setup List is 408.

2-12) Scheduler status query
Command
get(getn,gett)

Option 1
MTX:EvntScd_On

Option 2
0

Option 3
0

Description
Queries the scheduler status

* For getn, the response will contain a normalized value; for gett, the response will contain a text string.
Response
Response string
OK get MTX:EvntScd_On 0 0 1
OK get MTX:EvntScd_On 0 0 0
Example:

Command:
Response:
Meaning:
		

Description
Scheduler on
Scheduler off

get MTX:EvntScd_On 0 0
OK get MTX:EvntScd_On 0 0 1
Query the scheduler status.
Enabled

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

25

3. Command Specifications
3.3.5. Parameter setting
2-13) Raw value parameter setting
MTX3,MTX5-D,XMV,EXi8,EXo8
Command
set
Details:

Option 1
MTX:mem_MemNo/UniqueId/ElmNo/
Xpos/Ypos/PrmNo/IndexNo
MemNo =
UniqueId =
ElmNo =
Xpos =
Ypos =
PrmNo =
IndexNo =
(value) =

Option 2
0

Option 3
0

Option 4
(value)

Description
Raw value parameter
setting

See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
See section 3.1, "Basic Command Specifications," or section 7, "Parameter List."

Response
Response string
OK set MTX:mem_MemNo/UniqueId/ElmNo/Xpos/Ypos/
PrmNo/IndexNo 0 0 (value) "(string)"
OKm set MTX:mem_MemNo/UniqueId/ElmNo/Xpos/Ypos/
PrmNo/IndexNo 0 0 (value) "(string)"

Description
Raw value parameter setting response

* If the requested parameter value is outside the range, the value is adjusted within the range and set.
If this occurs, the result notification will be OKm instead of OK.
Details:

MemNo =
UniqueId =
ElmNo =
Xpos =
Ypos =
PrmNo =
IndexNo =
(value) =
"(string)" =

Example:

Command:
Response:
Meaning:
		

See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
See section 3.1, "Basic Command Specifications," or section 7, "Parameter List."
See section 3.1, "Basic Command Specifications," or section 7, "Parameter List."
set MTX:mem_512/60000/0/0/0/0/0 0 0 -7760
OK set MTX:mem_512/60000/0/0/0/0/0 0 0 -7760 "-77.60"
Set the 1ch level of the DCA fader to a raw value of -77.60.
The 1ch level of the DCA fader was set to "-77.60".

MRX7-D
Command
set

Option 1
MTX:Index_IndexNo

Option 2

Details:

IndexNo = Index number assigned in Remote Control Setup List
(value) = See section 3.1, "Basic Command Specifications," or section 7, "Parameter List."

0

Option 3
0

Option 4
(value)

Description
Raw value parameter
setting

Response
Response string
OK set MTX:Index_IndexNo 0 0 (value) "(string)"
OKm set MTX:Index_IndexNo 0 0 (value) "(string)"

Description
Raw value parameter setting response

* If the requested parameter value is outside the range, the value is adjusted within the range and set.
If this occurs, the resulting notification will be Okm instead of OK.
Details:

Example:

IndexNo = Index number assigned in Remote Control Setup List
(value) = See section 3.1, "Basic Command Specifications," or section 7, "Parameter List."
"(string)" = See section 3.1, "Basic Command Specifications," or section 7, "Parameter List."

Command:
Response:
		
Meaning:
		

set MTX:Index_1 0 0 -7760
OK set MTX:Index_1 0 0 -7760 "-77.60"
(V2.02 or earlier OK set MTX:Index_001 0 0 -7760 "-77.60")
Set the parameter assigned to Index 1 in Remote Control Setup List to -77.60 using raw values.
Level of a parameter which is assigned to Index 1 in Remote Control Setup List was set to "-77.60".

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

26

3. Command Specifications
2-14) Normalized value parameter setting
MTX3,MTX5-D,XMV,EXi8,EXo8
Command
setn

Option 1
MTX:mem_MemNo/UniqueId/ElmNo/
Xpos/Ypos/PrmNo/IndexNo

Details:

MemNo =
UniqueId =
ElmNo =
Xpos =
Ypos =
PrmNo =
IndexNo =
(value) =
		

Option 2
0

Option 3
0

Option 4
(value)

Description
Normalized value
parameter setting

See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
See section 3.1, "Basic Command Specifications," or section 7, "Parameter List." (*)
* When value is set "1023" (default:1000), control resolution becomes same as "Raw value" command.
See "6.1 Fader parameter " for the "Nomalised value" vs "Raw value" when the value is set "1023"

Response
Response string
OK setn MTX:mem_MemNo/UniqueId/ElmNo/Xpos/Ypos/
PrmNo/IndexNo 0 0 (value) "(string)"
OKm setn MTX:mem_MemNo/UniqueId/ElmNo/Xpos/Ypos/
PrmNo/IndexNo 0 0 (value) "(string)"

Description
Normalized value parameter setting response

* If the requested parameter value is outside the range, the value is adjusted within the range and set.
If this occurs, the result notification will be OKm instead of OK.
Details:

MemNo =
UniqueId =
ElmNo =
Xpos =
Ypos =
PrmNo =
IndexNo =
(value) =
"(string)" =

Example:

Command:
Response:
Meaning:
		

See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
See section 3.1, "Basic Command Specifications," or section 7, "Parameter List."
See section 3.1, "Basic Command Specifications," or section 7, "Parameter List."
setn MTX:mem_512/60000/0/0/0/0/0 0 0 408
OKm setn MTX:mem_512/60000/0/0/0/0/0 0 0 408 "-20.56"
Set the 1ch level of the DCA fader to a normalized value of 408.
The 1ch level of the DCA fader was set to "-20.56".

MRX7-D
Command
setn

Option 1
MTX:Index_IndexNo

Option 2
0

Option 3
0

Option 4
(value)

Description
Normalized value
parameter setting

Details:

IndexNo = Index number assigned in Remote Control Setup List
(value) = See section 3.1, "Basic Command Specifications," or section 7, "Parameter List."(*)
		 * When value is set "1023" (default:1000), control resolution becomes same as "Raw value" command.
See "6.1 Fader parameter " for the "Nomalised value" vs "Raw value" when the value is set "1023"
Response
Response string
OK setn MTX:Index_IndexNo 0 0 (value) "(string)"
OKm setn MTX:Index_IndexNo 0 0 (value) "(string)"

Description
Normalized value parameter setting response

* If the requested parameter value is outside the range, the value is adjusted within the range and set.
If this occurs, the result notification will be OKm instead of OK.
Details:

Example:

IndexNo = Index number assigned in Remote Control Setup List
(value) = See section 3.1, "Basic Command Specifications," or section 7, "Parameter List."
"(string)" = See section 3.1, "Basic Command Specifications," or section 7, "Parameter List."

Command:
Response:
		
Meaning:
		

setn MTX:Index_1 0 0 408
OK setn MTX:Index_1 0 0 408 "-21.50"
(V2.02 or earlier OK setn MTX:Index_001 0 0 408 "-21.50")
Set a parameter assigned to Index 1 in Remote Control Setup List to 408 using normalized values.
Level of a parameter which is assigned to index 1 in Remote Control Setup List was set to 408 "-21.50".

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

27

3. Command Specifications
2-15) Relative value parameter setting
MTX3,MTX5-D,XMV,EXi8,EXo8
Command
setr

Option 1
MTX:mem_MemNo/UniqueId/ElmNo/
Xpos/Ypos/PrmNo/IndexNo

Details:

MemNo =
UniqueId =
ElmNo =
Xpos =
Ypos =
PrmNo =
IndexNo =
"(value)" =
		
Note:

Option 2
0

Option 3
0

Option 4
"(value)"

Description
Relative value set
command.

See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
relative value to increase or decrease.
(See "Fader Parameter" table in section 6 Parameter Value Details )

This command is available only for fader type parameters. See "Remarks" column in section 7 Parameter List for
information regarding which parameters support this command.
The Parameter will be set to a new value which equals the sum of the parameter's original value and the relative value
given by this command.
The parameter value range is 0 - 1023 as shown in the "Fader Parameter" table in section 6 Parameter Value Details.
For example, when the relative value is set to 64, 16 level steps can be achieved from the remote controller.
(1024/64 = 16)

Response
Response string
OK setr MTX:mem_MemNo/UniqueId/ElmNo/Xpos/Ypos/
PrmNo/IndexNo 0 0 (value)
OKm setr MTX:mem_MemNo/UniqueId/ElmNo/Xpos/Ypos/
PrmNo/IndexNo 0 0 (value)

Description
Relative value set command response.

* When the sum of current value and relative value is outside of parameter value range (0-1023), a limiting process is
automatically applied.
In such case, "OKm" response will be sent back, instead of normal "OK" response.
Details:

MemNo =
UniqueId =
ElmNo =
Xpos =
Ypos =
PrmNo =
IndexNo =
"(value)" =
		

See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
See section 7, "Parameter List."
relative value to increase or decrease.
(See "Fader Parameter" table in section 6 Parameter Value Details )

Example:

setr MTX:mem_512/60000/0/0/0/0/0 0 0 100
OK setr MTX:mem_512/60000/0/0/0/0/0 0 0 -1900
Set DCA-A Fader to+100 step increase.
The level of the DCA-A fader was set to "-19.00"dB.

Command:
Response:
Meaning:
		

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

28

3. Command Specifications
MRX7-D
Command
setr

Option 1
MTX:Index_IndexNo

Option 2
0

Option 3

Option 4
"(value)"

0

Description
Relative value set
command.

Details:

IndexNo = Index number assigned in Remote Control Setup List
(value) = relative value to increase or decrease.
		 (See "Fader Parameter" table in section 6 Parameter Value Details )
Note:

This command is available only for fader type parameters. See "Remarks" column in section 7 Parameter List for
information regarding which parameters support this command.
The Parameter will be set to a new value which equals the sum of the parameter's original value and the relative value
given by this command.
The parameter value range is 0 - 1023 as shown in the "Fader Parameter" table in section 6 Parameter Value Details.
For example, when the relative value is set to 64, 16 level steps can be achieved from the remote controller.
(1024/64 = 16)

Response
Response string
OK setr MTX:Index_IndexNo 0 0 (value)
OKm setr MTX:Index_IndexNo 0 0 (value)

Description
Normalized value parameter setting response

* If the requested parameter value is outside the range, the value is adjusted within the range and set.
If this occurs, the result notification will be OKm instead of OK.
Details:

IndexNo = Index number assigned in Remote Control Setup List
(value) = relative value to increase or decrease.
		 (See "Fader Parameter" table in section 6 Parameter Value Details )
Example:

Command:
Response:
		
Meaning:
		

setr MTX:Index_1 0 0 100
OK setr MTX:Index_1 0 0 -1900
(V2.02 or earlier OK setr MTX:Index_001 0 0 -1900)
Set the parameter assigned to index 1 in Remote Control Setup List to 100 step increase.
Level of the parameter which is assigned to index 1 in Remote Control Setup List was set to "-19.00".

2-16) Scheduler setting
Command
set(setn,sett)

Option 1
MTX:EvntScd_On 0

Option 2

Option 3
0

Option 4
1
0

Description
Scheduler on
Scheduler off

* For setn, specify a normalized value; for sett, specify option 4 with a character string.
Response
Response string
OK set MTX:EvntScd_On 0 0 1 "1"
OK set MTX:EvntScd_On 0 0 0 "0"
Example:

Command:
Response:
Meaning:
		

Description
Scheduler enabled response
Scheduler disabled response

set MTX:EvntScd_On 0 0 1
OK set MTX:EvntScd_On 0 0 1 "1"
Enable the scheduler.
The scheduler was enabled.

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

29

3. Command Specifications
3.3.6. Meter control
2-17) Transmission request
MTX3,MTX5-D,XMV,EXi8,EXo8
Command
mtrstart
Details:

Option 1
Option 3
MTX:mtr_MemNo/UniqueId/meter (interval)

Description
Requests that the specified meter data be transmitted.

MemNo = See section 8, "Meter List."
UniqueId = See section 8, "Meter List."
(interval) = Minimum transmission interval (msec)

Response
Response string
OK mtrstart MTX:mtr_MemNo/UniqueId/meter
Details:

Example:

Description
Meter data transmission setting complete

MemNo = See section 8, "Meter List."
UniqueId = See section 8, "Meter List."

Command:
Notification:
		
		
		
Meaning:
		

mtrstart MTX:mtr_512/20020/meter 1000
OK mtrstart MTX:mtr_512/20020/meter
NOTIFY mtr MTX:mtr_512/20020/meter level 71 71 71 71 71 71 69 68
NOTIFY mtr MTX:mtr_512/20020/meter level 71 71 71 71 71 71 69 68
* The meter value is expressed using a 2-digit hexadecimal.
Send the meter data of ch1 to 8 output levels at 1000 msec intervals.
A request for the ch1 to 8 output levels was received, so the data will be transmitted.

MRX7-D
Command
mtrstart

Option 1
MTX:Index_IndexNo

Option 2
level

Option 3
(interval)

gr
hold
Details:

Description
Requests specified level meter data be
transmitted.
Requests specified Gain Reduction meter
data be transmitted.
Requests specified Hold meter data be
transmitted.

IndexNo = Index number assigned in Remote Control Setup List
(interval) = Minimum transmission interval (msec)

Response
Response string
OK mtrstart MTX:Index_IndexNo level
OK mtrstart MTX:Index_IndexNo gr
OK mtrstart MTX:Index_IndexNo hold
Details:

Description
Level meter data transmission setting complete
Gain Reduction meter data transmission setting complete
Hold meter data transmission setting complete

IndexNo = Index number assigned in Remote Control Setup List

Example:

Command: mtrstart MTX:Index_2 level 1000
Notification: OK mtrstart MTX:Index_2 level
		 NOTIFY mtr MTX:Index_2 level 71 71 71 71 71 71 69 68
		 NOTIFY mtr MTX:Index_2 level 71 71 71 71 71 71 69 68
		 (V2.02 or earlier OK mtrstart MTX:Index_002 level
			
NOTIFY mtr MTX:Index_002 level 71 71 71 71 71 71 69 68
			
NOTIFY mtr MTX:Index_002 level 71 71 71 71 71 71 69 68)
		 * The meter value is expressed using a 2-digit hexadecimal.
Meaning: Send the meter data of ch1 to 8 which are assigned to Index 1 in Remote Control Setup List using
		 1000 msec intervals.
		 A request for Ch1 to 8 which are assigned to Index 1 in Remote control Setup List was received,
		 data will be transmitted.

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

30

3. Command Specifications
2-18) Stop request
MTX3,MTX5-D,XMV,EXi8,EXo8
Command
mtrstop
Details:

Option 1
MTX:mtr_MemNo/UniqueId/meter

Description
Requests that the specified meter data be stopped.

MemNo = See section 8, "Meter List."
UniqueId = See section 8, "Meter List."

Response
Response string
OK mtrstop MTX:mtr_MemNo/UniqueId/meter
Details:

Description
Meter data stop setting complete

MemNo = See section 8, "Meter List."
UniqueId = See section 8, "Meter List."

Example:

Command:
Notification:
Meaning:
		

mtrstop MTX:mtr_512/20020/meter
OK mtrstop MTX:mtr_512/20020/meter
Stop the meter data of ch1 to 8 output levels.
The request to stop the meter data of ch1 to 8 output levels was received.

MRX7-D
Command
mtrstop

Option 1
MTX:Index_IndexNo

Option 3
level
gr
hold

Details:

Description
Requests that the specified level meter data be stopped
Requests that the specified Gain Reduction meter data be
stopped
Requests that the specified hold meter data be stopped

IndexNo = Index number assigned in Remote Control Setup List

Response
Response string
OK mtrstop MTX:Index_IndexNo level
OK mtrstop MTX:Index_IndexNo gr
OK mtrstop MTX:Index_IndexNo hold
Details:
Example:

Description
Level meter data stop setting complete
Gain Reduction meter data stop setting complete
Hold meter data stop setting complete

IndexNo = Index number assigned in Remote Control Setup List

Command:
Notification:
		
Meaning:
		
		

mtrstop MTX:Index_2 level
OK mtrstop MTX:Index_2 level
(V2.02 or earlier OK mtrstop MTX:Index_002 level)
Stop the meter data of ch1 to 8 which are assigned to Index 2 in Remote Control Setup List.
The request to stop the meter data of ch1 to 8 which are assigned to Index 2 in Remote Control
Setup List was received.

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

31

3. Command Specifications
3.3.7. Preset processing
2-19) Preset current number query processing
Command

Description
Queries the current preset number (index)

sscurrent
Response
Response string
OK sscurrent (index) unmodified

Description
Current preset number queried
(There is no parameter change after recalling.)
Current preset number queried
(There is a parameter change after recalling.)

OK sscurrent (index) modified
Details:

(index) = Current preset number

Example:

Command:
Notification:
Meaning:
		
		

sscurrent
OK sscurrent 10 unmodified
Query the last index number (preset number) that was recalled.
The index number (preset number) is index 10 (preset 10), and no parameter has changed after
recalling.

2-20) Preset recall processing
Command

Option 1

ssrecall

(index)

Details:

(index) = Snapshot (preset) number

Description
Recalls the preset at the specified index from the preset list.

Response
Response string

Description

OK ssrecall (index)
Details:

Requested index

(index) = Snapshot (preset) number

Example:

Command:
Notification:
Meaning:
		

ssrecall 1
OK ssrecall 1
Recall the preset at index 1 (preset 1).
The preset at index 1 (preset 1) was recalled.

3.3.8. Snapshot Recall processing
2-21) Snapshot recall processing
Command
ssrecall_ex
Details:

Option 1
list

Option 2
(index)

Description
Recall Snapshot or SnapshotGroup assigned in Remote
Control Setup List.

Index = Index number assigned in Remote Control Setup List

Response
Response string
OK ssrecall_ex list (index)
Details:
Example:

Description
Index number assigned in Remote Control Setup List

Index = Index number assigned in Remote Control Setup List

Command:
Notification:
Meaning:
		

ssrecall_ex list 3
OK ssrecall_ex list 3
Recall the Snapshot assigned to index 3 in Remote Control Setup List.
The Snapshot assigned to Index 2 in Remote Control Setup List was recalled.

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

32

3. Command Specifications

3.4. Extended commands
3.4.1. Product information query request
3-1) MTX external control protocol version query
Command

Option 1

devinfo

protocolver

Description
Queries the MTX external control protocol version

Response
Response string
OK devinfo protocolver "xxxx"
Details:

Description
MTX external control protocol version

xxxx = Version

Example:

Command:
Notification:
Meaning:
		

devinfo protocolver
OK devinfo protocolver "1.0.0"
Query the protocol version.
Protocol version = V1.0.0

3-2) Parameter set version query
Command

Option 1
paramsetver

devinfo

Description
Queries the parameter set version

Response
Response string
OK devinfo paramsetver "xxxx"
Details:

Description
Parameter set version

xxxx = Version

Example:

Command:
Notification:
Meaning:
		

devinfo paramsetver
OK devinfo paramsetver "MTX:1.2.0"
Query the parameter set version.
Parameter set version = V1.2.0

3-3) Firmware version query
Command
devinfo

Option 1
version

Description
Queries the firmware version

Response
Response string
OK devinfo version "xxxx"
Details:

Description
Firmware version

xxxx = Version

Example:

Command:
Notification:
Meaning:
		

devinfo version
OK devinfo version "1.0.0"
Query the firmware version.
Firmware version = V1.00

3-4) Product name query
Command
devinfo

Option 1
productname

Description
Queries the product name

Response
Response string
OK devinfo productname "xxxx"
Details:
Example:

Description
Product name

xxxx = Product name

Command:
Notification:
Meaning:
		

devinfo productname
OK devinfo productname "MTX3"
Query the product name.
Product name = "MTX3"

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

33

3. Command Specifications
3-5) Serial number query
Command
devinfo

Option 1
serialno

Description
Queries the serial number

Response
Response string
OK devinfo serialno "xxxx"
Details:

Description
Serial number

xxxx = Serial number

Example:

Command:
Notification:
Meaning:
		

devinfo serialno
OK devinfo serialno "ZA37640CHNET101001"
Query the serial number.
Serial number = "ZA37640CHNET101001"

3-6) Device ID query
Command
devinfo

Option 1
deviceid

Description
Queries the device ID

Response
Response string
OK devinfo deviceid "xxxx"

Description
Device ID

Details:
xxxx = Device ID
		 * 3-digit hexadecimal
Example:

Command:
Notification:
Meaning:
		
Note:

devinfo deviceid
OK devinfo deviceid "001"
Query the device ID.
Device ID = "001"

The device ID corresponds to the UNIT ID.

3-7) Device name query
Command
devinfo

Option 1
devicename

Description
Queries the device name assigned by the user

Response
Response string
OK devinfo devicename "xxxx"
Details:
Example:

xxxx = Device name

Command:
Notification:
Meaning:
		
Note:

Description
Device name assigned by the user

devinfo devicename
OK devinfo devicename "MTX3"
Query the device name.
Device name = "MTX3"

The character encoding for the device name conforms to the setting specified by the scpmode encoding command.

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

34

3. Command Specifications
3.4.2. Preset processing request
3-8) Number of Preset lists
Command

Description
Queries the number of preset lists

Response string

Description
The number of preset lists

ssnum
Response
OK ssnum (num)
Details:

(num) = Quantity

Example:

Command:
Notification:
Meaning:
		

ssnum
OK ssnum 51
Query the number of presets.
The number of presets is 51.

3-9) Nth preset information
Command
ssinfo

Option 1
(index)

Description
Queries the preset information at the specified index in the
preset list.

Response
Response string
OK ssinfo (index) "xxxxxx" (attrib) "yyyyyy" "zzzzzz"

Description
Preset information at the specified index in the preset list.

Details:

(index) = Requested index number
"xxxxxxx" = Text expressing the relevant preset number
(attrib) = Relevant preset attribute
		 preinst = preinstalled preset
		 reserve = reserved area
		 user
= user preset available
		 empty = empty
"yyyyyyy" = = title text of the relevant preset
"zzzzzz" = comment text of the relevant preset.
		
(reserved for future use. MTX does not currently use comments. "" will be returned.)
Example:

Command:
Notification:
Meaning:
		
		
		
		
		
Note:

ssinfo 10
OK ssinfo 10 "10" user "Preset 10" ""
Query the contents of the preset at index 10 (preset 10).
The preset at index 10 contains
display number = "10"
title = "Preset 10"
comment = ""
and is a stored preset.

The character encoding for preset titles and comments conforms to the setting specified by the scpmode encoding
command.

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

35

3. Command Specifications
3.4.3. Event processing request
3-10) Time synchronization 
Command
event
Details:

yyyy =
mm =
dd =
hh =
mm =
ss =
		

Option 1
MTX:AbsoluteTime

Option 2
"yyyy/mm/dd hh:mm:ss"

Description
Changes the time

Year (Gregorian)
Month (1 to 12)
Day (1 to 31)
Hour (0 to 23)
Minute (0 to 59)
Second (0 to 59)
* DST (Daylight Saving Time) is not accounted for.

Response
Response string
OK event MTX:AbsoluteTime "caught"
Example:

Command:
Notification:
Meaning:
		

Description
Time change complete

event MTX:AbsoluteTime "2013/1/25 11:56:14"
OK event MTX:AbsoluteTime "caught"
Set the time to January 25, 2013, 11 hours 56 minutes 14 seconds.
The time was set.

3-11) Time synchronization 
Command
event
Details:

yyyy =
mm =
dd =
hh =
mm =
ss =
		

Option 1
MTX:SetAbsoluteTime

Option 2
"yyyy/mm/dd hh:mm:ss"

Description
Changes the time

Year (Gregorian)
Month (1 to 12)
Day (1 to 31)
Hour (0 to 23)
Minute (0 to 59)
Second (0 to 59)
* DST (Daylight Saving Time) is not accounted for.

Response
Response string
OK event MTX:SetAbsoluteTime "caught"
Example:

Command:
Notification:
Meaning:
		

Description
Time change complete

event MTX:SetAbsoluteTime "2013/1/25 11:56:14"
OK event MTX:SetAbsoluteTime "caught"
Set the time to January 25, 2013, 11 hours 56 minutes 14 seconds.
The time was set.

3-12) Time query
Command
event

Option 1
MTX:GetAbsoluteTime

Option 2
""

Description
Time query with absolute time

Response
Response string
OK event MTX:GetAbsoluteTime "yyyy/mm/dd hh:mm:ss"

Description
Current time info with absolute time

Details:

yyyy =
mm =
dd =
hh =
mm =
ss =
		

Year (Gregorian)
Month (1 to 12)
Day (1 to 31)
Hour (0 to 23)
Minute (0 to 59)
Second (0 to 59)
* DST (Daylight Saving Time) is not accounted for.

Example:

event MTX:GetAbsoluteTime ""
OK event MTX:GetAbsoluteTime "2014/1/25 11:56:14"
Get current time with absolute time
Current time is January 25 2014, 11 hours 56 minutes 14 seconds

Command:
Notification:
Meaning:
		

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

36

3. Command Specifications
3-13) DST enable/disable setting
Command

Option 1
MTX:DSTSetEnable

event

Option 2
"enable"
"disable"

Description
Set DST enable
Set DST disable

Response
Response string
OK event MTX:DSTSetEnable "enable"
OK event MTX:DSTSetEnable "disable"
Example:

Command:
Notification:
Meaning:
		

Description
DST was enabled
DST was disabled

event MTX:DSTSetEnable "enable"
OK event MTX:DSTSetEnable "enable"
Set DST enable
DST was enabled

3-14) DST enable/disable query
Command

Option 1
MTX:DSTGetEnable

event

Option 2
""

Description
DST enable/disable query

Response
Response string
OK event MTX:DSTGetEnable "enable"
OK event MTX:DSTGetEnable "disable"
Example:

Command:
Notification:
Meaning:
		

Description
DST is enable
DST is disable

event MTX:DSTGetEnable ""
OK event MTX:DSTGetEnable "enable"
Get DST setting
DST is enable

3-15) DST status query
Command

Option 1
MTX:DSTGetStatus

event

Option 2
""

Description
DST status query

Response
Response string
OK event MTX:DSTGetStatus "on"
OK event MTX:DSTGetStatus "off"
Example:

Command:
Notification:
Meaning:
		

Description
Working with DST
Not working with DST

event MTX:DSTGetStatus ""
OK event MTX:DSTGetStatus "on"
Get DST working status
Working with DST

3-16) DST offset time setting
Command
event

Option 1
MTX:DSTSetOffset

Option 2
"offset=hh:mm"

Description
Set DST offset

Details:

hh = Hour (0 to 2)
mm = Minute (0 to 59)
		 (Up to 2 hours can be set)
Response
Response string
OK event MTX:DSTSetOffset "offset=hh:mm"
Details:

Example:

Description
DST offset was set

hh = Hour (0 to 2)
mm = Minute (0 to 59)

Command:
Notification:
Meaning:
		

event MTX:DSTSetOffset "offset=1:00"
OK event MTX:DSTSetOffset "offset=1:00"
Set DST offset to 1 hour
DST offset was set to 1 hour

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

37

3. Command Specifications
3-17) DST offset time query
Command

Option 1
MTX:DSTGetOffset

event

Option 2
""

Description
Get DST offset

Response
Response string
OK event MTX:DSTGetOffset "offset=hh:mm"
Details:

Description
DST offset

hh = Hour (0 to 2)
mm = Minute (0 to 59)

Example:

Command:
Notification:
Meaning:
		

event MTX:DSTGetOffset ""
OK event MTX:DSTGetOffset "offset=01:00"
Get DST offset
DST offset was set to 1 hour

3-18) DST start time setting
Command
event
Details:

Option 1
MTX:DSTSetStartTime

Option 2
"time=hh:mm"

Description
Set DST start time

hh = Hour (0 to 23)
mm = Minute (0 to 59)

Response
Response string
OK event MTX:DSTSetStartTime "time=hh:mm"
Details:

Description
DST start time was set

hh = Hour (0 to 23)
mm = Minute (0 to 59)

Example:

Command:
Notification:
Meaning:
		

event MTX:DSTSetStartTime "time=12:00"
OK event MTX:DSTSetStartTime "time=12:00"
Set DST start time to 12:00
DST start time was set to 12:00

3-19) DST start time query
Command
event

Option 1
MTX:DSTGetStartTime

Option 2
""

Description
Get DST start time

Response
Response string
OK event MTX:DSTGetStartTime "time=hh:mm"
Details:

Example:

Description
DST start time

hh = Hour (0 to 23)
mm = Minute (0 to 59)

Command:
Notification:
Meaning:
		

event MTX:DSTGetStartTime ""
OK event MTX:DSTGetStartTime "time=12:00"
Get DST start time
DST start time is 12:00

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

38

3. Command Specifications
3-20) DST end time setting
Command
event
Details:

Option 1
MTX:DSTSetEndTime

Option 2
"time=hh:mm"

Description
Set DST end time

hh = Hour (0 to 23)
mm = Minute (0 to 59)

Response
Response string
OK event MTX:DSTSetEndTime "time=hh:mm"
Details:

Description
DST end time was set

hh = Hour (0 to 23)
mm = Minute (0 to 59)

Example:

Command:
Notification:
Meaning:
		

event MTX:DSTSetEndTime "time=12:00"
OK event MTX:DSTSetEndTime "time=12:00"
Set DST end time to 12:00
DST end time was set to 12:00

3-21) DST end time query
Command
event

Option 1
MTX:DSTGetEndTime

Option 2
""

Description
Get DST end time

Response
Response string
OK eventMTX:DSTGetEndTime "time=hh:mm"
Details:

Description
DST end time

hh = Hour (0 to 23)
mm = Minute (0 to 59)

Example:

Command:
Notification:
Meaning:
		

event MTX:DSTGetEndTime ""
OK event MTX:DSTGetEndTime "time=12:00"
Get DST end time
DST end time is 12:00

3-22) DST start/end days setting (day/week)
Command
event
Details:

Option 1
MTX:DSTSetDayWeek
xxxx =
yyyy =
zzzz =
uuuu =
vvvv =
wwww =

Option 2
Description
"s_weekindex=xxxx|s_day=yyyy|s_month=zzzz|
Set DST start/end days by day
e_weekindex=uuuu|e_day=vvvv|e_month=wwww" and week

Start week (First, Second, Third, Fourth, Fifth, Last)
Start day (Sun, Mon, Tue, Wed, Thu, Fri, Sat)
Start month (Jan, Feb, Mar, Apr, May, Jun, Jul, Aug, Sep, Oct, Nov, Dec)
End week (First, Second, Third, Fourth, Fifth, Last)
End day (Sun, Mon, Tue, Wed, Thu, Fri, Sat)
End month (Jan, Feb, Mar, Apr, May, Jun, Jul, Aug, Sep, Oct, Nov, Dec)

Response
Response string
OK event MTX:DSTSetDayWeek "s_weekindex=xxxx|s_day=yyyy|
s_month=zzzz|e_weekindex=uuuu|e_day=vvvv|e_month=wwww"
Details:

xxxx =
yyyy =
zzzz =
uuuu =
vvvv =
wwww =

Example:
Command:
		
Notification:
		
Meaning:
		

Description
DST start/end days by day and week was set

Start week (First, Second, Third, Fourth, Fifth, Last)
Start day (Sun, Mon, Tue, Wed, Thu, Fri, Sat)
Start month (Jan, Feb, Mar, Apr, May, Jun, Jul, Aug, Sep, Oct, Nov, Dec)
End week (First, Second, Third, Fourth, Fifth, Last)
End day (Sun, Mon, Tue, Wed, Thu, Fri, Sat)
End month (Jan, Feb, Mar, Apr, May, Jun, Jul, Aug, Sep, Oct, Nov, Dec)
event MTX:DSTSetDayWeek "s_weekindex=Last|s_day=Sun|s_month=Mar|e_weekindex=Last|
e_day=Sun|e_month=Oct"
OK event MTX:DSTSetDayWeek "s_weekindex=Last|s_day=Sun|s_month=Mar|
e_weekindex=Last|e_day=Sun|e_month=Oct"
Set DST start/end days as from last Sunday in March to last Sunday in October
DST start/end days was set as from last Sunday in March to last Sunday in October

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

39

3. Command Specifications
3-23) DST start/end days query (day/week)
Command
event

Option 1
MTX:DSTGetDayWeek

Option 2
""

Description
Get DST start/end days by day and week

Response
Response string
OK event MTX:DSTGetDayWeek "s_weekindex=xxxx|s_day=yyyy|
s_month=zzzz|e_weekindex=uuuu|e_day=vvvv|e_month=wwww"
Details:

xxxx =
yyyy =
zzzz =
uuuu =
vvvv =
wwww =

Example:

Command:
Notification:
		
Meaning:
		
Note:

Description
DST start/end days by day and week

Start week (First, Second, Third, Fourth, Fifth, Last)
Start day (Sun, Mon, Tue, Wed, Thu, Fri, Sat)
Start month (Jan, Feb, Mar, Apr, May, Jun, Jul, Aug, Sep, Oct, Nov, Dec)
End week (First, Second, Third, Fourth, Fifth, Last)
End day (Sun, Mon, Tue, Wed, Thu, Fri, Sat)
End month (Jan, Feb, Mar, Apr, May, Jun, Jul, Aug, Sep, Oct, Nov, Dec)
event MTX:DSTGetDayWeek ""
OK event MTX:DSTGetDayWeek "s_weekindex=Last|s_day=Sun|s_month=Mar|
e_weekindex=Last|e_day=Sun|e_month=Oct"
Get DST start/end days by day and week
DST start/end days is set as from last Sunday in March to last Sunday in October

When DST is set not by "day and week" but by "day", error returns.

3-24) DST start/end days setting (day)
Command
event
Details:

Option 1
MTX:DSTSetDay
xxxx =
yyyy =
zzzz =
wwww =

Option 2
"s_month=xxxx|s_date=yyyy|e_month=zzzz|
e_date=wwww"

Description
Set DST start/end days by day

Start month (Jan, Feb, Mar, Apr, May, Jun, Jul, Aug, Sep, Oct, Nov, Dec)
Start day (1 ~ 31)
End month (Jan, Feb, Mar, Apr, May, Jun, Jul, Aug, Sep, Oct, Nov, Dec)
End day (1 ~ 31)

Response
Response string
OK event MTX:DSTSetDay "s_month=xxxx|s_date=yyyy|
e_month=zzzz|e_date=wwww"
Details:

Example:

xxxx =
yyyy =
zzzz =
wwww =

Command:
Notification:
Meaning:
		

Description
DST start/end days by day was set

Start month (Jan, Feb, Mar, Apr, May, Jun, Jul, Aug, Sep, Oct, Nov, Dec)
Start day (1 ~ 31)
End month (Jan, Feb, Mar, Apr, May, Jun, Jul, Aug, Sep, Oct, Nov, Dec)
End day (1 ~ 31)
event MTX:DSTSetDay "s_month=Mar|s_date=10|e_month=Nov|e_day=3"
OK event MTX:DSTSetDay "s_month=Mar|s_date=10|e_month=Nov|e_day=3"
Set DST start/end days as from March 10 to November 3
DST start/end days was set as from March 10 to November 3

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

40

3. Command Specifications
3-25) DST start/end days query (day)
Command
event

Option 1
MTX:DSTGetDay

Option 2
""

Description
Set DST start/end days by day

Response
Response string
Description
OK event MTX:DSTGetDay "s_month=xxxx|s_date=yyyy|e_month=zzzz|e_date=wwww" DST start/end days by day
Details:

xxxx =
yyyy =
zzzz =
wwww =

Example:

Command:
Notification:
Meaning:
		
Note:

Start month (Jan, Feb, Mar, Apr, May, Jun, Jul, Aug, Sep, Oct, Nov, Dec)
Start day (1 ~ 31)
End month (Jan, Feb, Mar, Apr, May, Jun, Jul, Aug, Sep, Oct, Nov, Dec)
End day (1 ~ 31)
event MTX:DSTGetDay ""
OK event MTX:DSTGetDay "s_month=Mar|s_date=10|e_month=Nov|e_day=3"
Get DST start/end days by date
DST start/end days is from March 10 to November 3

When DST is set not by "day" but by "day and week", error returns.

3-26) DST start/end days setting query
Command
event

Option 1
MTX:DSTGetDaySetting

Option 2
""

Description
Get DST start/end days format, "day
and week" or "day"

Response
Response string
OK event MTX:DSTGetDaySetting "setting=dayweek"
OK event MTX:DSTGetDaySetting "setting=day"
Example:

Command:
Notification:
Meaning:
		

Description
DST start/end days are set by "day and week"
DST start/end days are set by "day"

event MTX:DSTGetDaySetting ""
OK event MTX:DSTGetDaySetting "setting=dayweek"
Get DST start/end days format, "day and week" or "day"
DST start/end days were set by "day and week"

3-27) Current folder information query
Command
event

Option 1
MTX:AudioPlayerGetCurrentDir

Option 2
""

Description
Queries the current folder information.

Response
Response string
OK event MTX:AudioPlayerGetCurrentDir "dirpath=xxxx|dirname=yyyy|
subdirnum=zzzz|filenum=wwww"
OKm event MTX:AudioPlayerGetCurrentDir "sdcard is not inserted"

Description
Current folder information
There is no SD memory card inserted.

* OKm is returned if there is no SD memory card inserted.
Details:
xxxx = Directory path (index expression)
			
0 : Root Folder Number(the root folder number is always fixed at 0)
			 0/nnnn : Root Folder Number/Sub Folder Number
yyyy = Directory name (name of the folder)
zzzz = The number of sub folders in the current directory
wwww = The number of files in the current directory
Example:

Command:
Notification:
Meaning:
		

event MTX:AudioPlayerGetCurrentDir ""
OK event MTX:AudioPlayerGetCurrentDir "dirpath=0|dirname=|subdirnum=4|filenum=2"
Query the current folder information.
The current folder contains four directories and two files.

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

41

3. Command Specifications
3-28) Current folder move query
Command
event

Option 1
MTX:AudioPlayerSetCurrentDir

Option 2
"dirpath=0"
"dirpath=0/nnnn"

Description
Moves the current folder(To root folder)
Moves the current folder(To sub folder)

Details:		 Directory path (index expression)
			
0 : Root Folder Number(the root folder number is always fixed at 0)
			 0/nnnn : Root Folder Number/Sub Folder Number
Note:

The range of sub folder is "0" to "total number of sub folders -1".
Use "3-27) Current folder information query" to get total number of sub folders
Song files in root folder of SD card and song files in sub folders of root folder are supported. Files placed in "deeper"
folders are not supported.

Response
Response string
OK event MTX:AudioPlayerSetCurrentDir "dirpath=xxxx|dirname=yyyy|
subdirnum=zzzz|filenum=wwww"
OKm event MTX:AudioPlayerSetCurrentDir "sdcard is not inserted"

Description
Current folder information
There is no SD memory card inserted.

* OKm is returned if there is no SD memory card inserted.
Details:
xxxx = Directory path (index expression)
			
0 : Root Folder Number(the root folder number is always fixed at 0)
			 0/nnnn : Root Folder Number/Sub Folder Number
yyyy = Directory name (name of the folder)
zzzz = The number of sub folders in the current directory
wwww = The number of files in the current directory
Example:

Command:
Notification:
Meaning:
		
		
		

event MTX:AudioPlayerSetCurrentDir "dirpath=0/1"
OK event MTX:AudioPlayerSetCurrentDir "dirpath=0/1|dirname=songs|subdirnum=0|filenum=3"
Make the 0/1 (index expression) directory the current directory.
The 0/1 (index expression) directory was made the current directory. This folder contains no sub
directories and three files.
* "0/1" expresses the root folder number/sub folder number (the root folder number is always fixed at 0).

3-29) Folder name query
Command
event
Details:
Note:

Option 1
MTX:AudioPlayerGetDirName

Option 2
"dirindex=xxxx"

Description
Folder name query

xxxx = Folder index number
The range of index numbers is "0" to "total number of sub folders - 1".
Use "3-27) Current folder information query" or "3-28) Current folder move query" to get total number of sub folders.
This command is valid only when current folder is “route”, otherwise (when current folder is sub folder) error will return.

Response
Response string
OK event MTX:AudioPlayerGetDirName "dirname=xxxx"
OKm event MTX:AudioPlayerGetDirName "sdcard is not inserted"

Description
Folder name
There is no SD memory card inserted.

* OKm is returned if there is no SD memory card inserted.
Details:
Example:

xxxx = Folder name

Command:
Notification:
Meaning:
		

event MTX:AudioPlayerGetDirName "dirindex=1"
OK event MTX:AudioPlayerGetDirName "dirname=songs"
Query the directory name of folder index number 1 (index expression).
The directory name is "songs".

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

42

3. Command Specifications
3-30) File name query
Command
event
Details:
Note:

Option 1
MTX:AudioPlayerGetFileName

Option 2
"fileindex=xxxx"

Description
File name query

xxxx = File index number
The range of index numbers is "0" to "total number of files - 1".
Use "3-27) Current folder information query" or "3-28) Current folder move query" to get total number of files.

Response
Response string
OK event MTX:AudioPlayerGetFileName "filename=xxxx"
OKm event MTX:AudioPlayerGetFileName "sdcard is not inserted"

Description
File name
There is no SD memory card inserted.

* OKm is returned if there is no SD memory card inserted.
Details:

xxxx = File name

Example:

Command:
Notification:
Meaning:
		

event MTX:AudioPlayerGetFileName "fileindex=1"
OK event MTX:AudioPlayerGetFileName "filename=xxxx.mp3"
Query the file name of file index number 1 (index expression).
The file name is "xxxx.mp3".

3-31) Folder name list query
Command
event
Details:

Note:

Option 1
MTX:AudioPlayerGetDirNameList

Option 2
Description
"dirindex=XXXX-xxxx" Folder name list: Multiple folder name
query

XXXX = the first index number of desired range for list (index expression)
xxxx = the last index number of desired range for list (index expression)
→ Cannot be set to a value greater than the number of folders.
→ The first number cannot be greater than the last number.
→ By changing the first and last numbers, you can query the list of folder names in that range.
"XXXX" should be 0 or greater.
"xxxx" should be smaller total number of sub folders - 1 or smaller.
Use "3-27) Current folder information query" or "3-28) Current folder move query" to get total number of sub folders.

Response
Response string
Description
OK event MTX:AudioPlayerGetDirNameList "dirindex=XXXX-xxxx|dirname0=yyyy| ... " Folder name list
OKm event MTX:AudioPlayerGetDirNameList "sdcard is not inserted"
There is no SD memory card inserted.
* OKm is returned if there is no SD memory card inserted.
Details:

Example:

XXXX = the first index number of desired range for list (index expression)
xxxx = the last index number of desired range for list (index expression)
yyyy = Directory names

Command:
Notification:
Meaning:
		

event MTX:AudioPlayerGetDirNameList "dirindex=0-1"
OK event MTX:AudioPlayerGetDirNameList "dirindex=0-1|dirname0=Folder #1|dirname1=Folder #2"
Query the directory names of folder list number 0 and 1 (index expression).
The directory name of folder list number 0 is "Folder #1", and that of folder list number 1 is "Folder #2".

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

43

3. Command Specifications
3-32) File name list query
Command
event
Details:

Note:

Option 1
MTX:AudioPlayerGetFileNameList

Option 2
Description
"fileindex=XXXX-xxxx" Folder name list: Multiple file name
query

XXXX = the first index number of desired range for list (index expression)
xxxx = the last index number of desired range for list (index expression)
→ Cannot be set to a value greater than the number of files.
→ The first number cannot be greater than the last number.
→ By changing the first and last numbers, you can query the list of file names in that range.
"XXXX" should be 0 or greater.
"xxxx" should be smaller total number of sub folders - 1 or smaller.
Use "3-27) Current folder information query" or "3-28) Current folder move query" to get total number of files.

Response
Response string
Description
OK event MTX:AudioPlayerGetFileNameList "fileindex=XXXX-xxxx|filename0=yyyy| ... " File name list
OKm event MTX:AudioPlayerGetFileNameList "sdcard is not inserted"
There is no SD memory card inserted.
* OKm is returned if there is no SD memory card inserted.
Details:

XXXX = the first index number of desired range for list (index expression)
xxxx = the last index number of desired range for list (index expression)
yyyy= File names

Example:

Command:
Notification:
Meaning:
		

event MTX:AudioPlayerGetFileNameList "fileindex=0-1"
OK event MTX:AudioPlayerGetFileNameList "fileindex=0-1|filename0=xxxx.mp3|filename1=xxxx2.mp3"
Query the file names of file list number 0 and 1 (index expression).
The file name of file list number 0 is "xxxx.mp3", and that of file list number 1 is "xxxx2.mp3".

3-33) Song play mode query
Command
event

Option 1
MTX:AudioPlayerGetPlayMode

Option 2
""

Description
Queries the play mode

Response
Response string
OK event MTX:AudioPlayerGetPlayMode "playmode=one"
OK event MTX:AudioPlayerGetPlayMode "playmode=repeat one"
OK event MTX:AudioPlayerGetPlayMode "playmode=all"
OK event MTX:AudioPlayerGetPlayMode "playmode=repeat all"
OK event MTX:AudioPlayerGetPlayMode "playmode=shuffle"
OKm event MTX:AudioPlayerGetPlayMode "sdcard is not inserted"

Description
One song play mode
One song repeat
All song play
All songs repeat
Shuffle repeat
There is no SD memory card inserted.

* OKm is returned if there is no SD memory card inserted.
Example:

Command:
Notification:
Meaning:
		

event MTX:AudioPlayerGetPlayMode ""
OK event MTX:AudioPlayerGetPlayMode "playmode=one"
Query the play mode.
The play mode is set to one song play mode.

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

44

3. Command Specifications
3-34) Song play mode setting
Command
event

Option 1
Option 2
MTX:AudioPlayerSetPlayMode "playmode=one"
"playmode=repeat one"
"playmode=all"
"playmode=repeat all"
"playmode=shuffle"

Description
One song play mode
One song repeat
All song play
All songs repeat
Shuffle repeat

Response
Response string
OK event MTX:AudioPlayerSetPlayMode "playmode=one"
OK event MTX:AudioPlayerSetPlayMode "playmode=repeat one"
OK event MTX:AudioPlayerSetPlayMode "playmode=all"
OK event MTX:AudioPlayerSetPlayMode "playmode=repeat all"
OK event MTX:AudioPlayerSetPlayMode "playmode=shuffle"
OKm event MTX:AudioPlayerSetPlayMode "sdcard is not inserted"

Description
One song play mode
One song repeat
All song play
All songs repeat
Shuffle repeat
There is no SD memory card inserted.

* OKm is returned if there is no SD memory card inserted.
Example:

Command:
Notification:
Meaning:
		

event MTX:AudioPlayerSetPlayMode "playmode=one"
OK event MTX:AudioPlayerSetPlayMode "playmode=one"
Set the play mode to one song play mode.
The play mode was set to one song play mode.

3-35) Song playback status query
Command
event

Option 1
MTX:AudioPlayerGetStatus

Option 2
""

Description
Song playback status query

Response
Response string
OK event MTX:AudioPlayerGetStatus "status=stop"
OK event MTX:AudioPlayerGetStatus "status=play"
OK event MTX:AudioPlayerGetStatus "status=pause"
OKm event OK event MTX:AudioPlayerGetStatus "sdcard is not inserted"

Description
Stop
Play
Pause
There is no SD memory card inserted.

* OKm is returned if there is no SD memory card inserted.
Example:

Command:
Notification:
Meaning:
		

event MTX:AudioPlayerGetStatus ""
OK event MTX:AudioPlayerGetStatus "status=stop"
Query the song playback status.
Stopped

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

45

3. Command Specifications
3-36) Play, stop, and other transport operation
Command
event

Option 1
MTX:AudioPlayerTransport

Option 2
"operation=stop"
"operation=play"
"operation=pause"
"operation=prev"
"operation=next"

Description
Stop
Play
Pause
Beginning of the previous song
Next song

Response
Response string
OK event MTX:AudioPlayerTransport "operation=stop"
OK event MTX:AudioPlayerTransport "operation=play"
OK event MTX:AudioPlayerTransport "operation=pause"
OK event MTX:AudioPlayerTransport "operation=prev"
OK event MTX:AudioPlayerTransport "operation=next"
OKm event MTX:AudioPlayerTransport "sdcard is not inserted"
OKm event MTX:AudioPlayerTransport "song is not set up"

Description
Stop
Play
Pause
Beginning of the previous song
Next song
There is no SD memory card inserted.
The playback song is not specified.

* OKm is returned if there is no SD memory card inserted or the playback song is not specified.
Example:

Command:
Notification:
Meaning:
		

event MTX:AudioPlayerTransport "operation=stop"
OK event MTX:AudioPlayerTransport "operation=stop"
Stop playback.
Playback was stopped.

3-37) Currently playing or selected song information query
Command
event

Option 1
MTX:AudioPlayerGetCurrentSong

Option 2
""

Description
Queries the currently playing or
selected song information

Response
Response string
OK event MTX:AudioPlayerGetCurrentSong "dirpath=xxxx|dirname=yyyy|
fileindex=zzzz|filename=wwww"
OKm event MTX:AudioPlayerGetCurrentSong "sdcard is not inserted"
OKm event MTX:AudioPlayerGetCurrentSong "song is not set up"

Description
Currently playing or selected song
information
There is no SD memory card inserted.
The playback song is not specified.

* OKm is returned if there is no SD memory card inserted or the playback song is not specified.
Details:
xxxx = Directory path (index expression)
			
0 : Root Folder Number(the root folder number is always fixed at 0)
			 0/nnnn : Root Folder Number/Sub Folder Number
yyyy = Directory name (name of the folder)
zzzz = File index number
wwww = File name
Example:

Command:
Notification:
		
Meaning:
		
		
		

event MTX:AudioPlayerGetCurrentSong ""
OK event MTX:AudioPlayerSetCurrentSong "dirpath=0/1|dirname=Folder #1|fileindex=2|
filename=xxxx.mp3"
Query the information of the song currently being played.
The song that is being played is index number 2 "xxxx.mp3" in the "Folder #1" folder of directory
path 0/1 (index expression).
* "0/1" expresses the root folder number/sub folder number (the root folder number is always fixed at 0).

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

46

3. Command Specifications
3-38) Playback song designation
Command
event

Option 1
Option 2
MTX:AudioPlayerSetCurrentSong "dirpath=xxxx|fileindex=yyyy"

Description
Playback song designation

Details:
xxxx= Directory path (index expression)
			
0 : Root Folder Number(the root folder number is always fixed at 0)
			 0/nnnn : Root Folder Number/Sub Folder Number
yyyy= File index number
Note:

The range of sub folder numbers is "0" to "total number of sub folders - 1".
The range of file numbers is "0" to "total number of files - 1".
Use "3-27) Current folder information query" or "3-28) Current folder move query" to get total number of sub folders
and files.
Song files in root folder of SD card and song files in sub folders in root folder are supported. Files placed in "deeper"
folder can't be supported.

Response
Response string
OK event MTX:AudioPlayerSetCurrentSong "dirpath=xxxx|dirname=yyyy|
fileindex=zzzz|filename=wwww"
OKm event MTX:AudioPlayerSetCurrentSong "sdcard is not inserted"

Description
The specified song that will be played
There is no SD memory card inserted.

* OKm is returned if there is no SD memory card inserted.
Details:
xxxx = Directory path (index expression)
			
0 : Root Folder Number(the root folder number is always fixed at 0)
			 0/nnnn : Root Folder Number/Sub Folder Number
yyyy = Directory name (name of the folder)
zzzz = File index number
wwww = File name
Example:

Command:
Notification:
		
Meaning:
		
		
		

event MTX:AudioPlayerSetCurrentSong "dirpath=0/1|fileindex=2"
OK event MTX:AudioPlayerSetCurrentSong "dirpath=0/1|dirname=Folder #1|fileindex=2|
filename=xxxx.mp3"
Play the file at file index number 2 in the directory path 0/1 folder (index expression).
The playback song was set to file index number 2 "xxxx.mp3" in "Folder #1" folder of directry path
0/1 (index expression).
* "0/1" expresses the root folder number/sub folder number (the root folder number is always fixed at 0).

3-39) MTX Editor synchronization processing query
Command
event

Option 1
MTX:SynchronizationGetStatus

Option 2
""

Description
MTX Editor synchronization
processing query

Response
Response string
OK event MTX:SynchronizationGetStatus "active"
OK event MTX:SynchronizationGetStatus "inactive"
Example:

Command:
Notification:
Meaning:
		
Note:

Description
In the process of synchronizing
Not in the process of synchronizing

event MTX:SynchronizationGetStatus ""
OK event MTX:SynchronizationGetStatus "inactive"
Query the synchronization status between the MTX and MTX Editor.
Not in the process of synchronizing

The character encoding for directory and file names conforms to the setting specified by the scpmode encoding
command.

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

47

3. Command Specifications
3-40) Number of alert event log query
Command
event

Option 1
MTX:EventLogGetLogNumber

Option 2
""

Description
Number of event log query

Response
Response string
OK event MTX:EventLogGetLogNumber "lognum=xxxx"
Details:

Description
Number of event log

xxxx= number of event log

Example:

Command:
Notification:
Meaning:
		

event MTX:EventLogGetLogNumber ""
OK event MTX:EventLogGetLogNumber "lognum=6"
Query the number of event logs
Number of event log is 6

3-41) Alert event log query
Command
event
Details:
Note:

Option 1
MTX:EventLogGetLog

Option 2
"logindex=xxxx"

Description
Event log query

xxxx= Index number of event log
The range of index numbers is "0" to "total number of event logs - 1".
Use "3-40) Number of alert event log query" to get total number of event logs.

Response
Response string
OK event MTX:EventLogGetLog "logxxxx=(AlertData)"

Description
Event log

Details:

xxxx= Index number of event log
(AlertData)= "flt/message// xnnn onf (sssss) ID-xxx yyyy/mm/dd hh:mm:ss"
		 "err/message// xnnn onf (sssss) ID-xxx yyyy/mm/dd hh:mm:ss"
		 "wrn/message// xnnn onf (sssss) ID-xxx yyyy/mm/dd hh:mm:ss"
		 First 3 letter describes type of event ( i.e. flt = fault, err = error, wrn = warning)
			 message = Alert message string - Maximum 32 letter (ascii character)
			
nnn = Alert number (same as number displayed on front panel of device)
				 - 2 or 3 digit hexadecimal.
			
onf = alert ON/OFF
				 Event of status change (e.g. wordclock unlock) sends ON when the remarkable
				 event starts, sends OFF when the event ends.
				 Momentary event (e.g. SD card player error) sends only ON when it happens.
			
sssss = counter of alarm ( Count up same Alert, normally as 1) as decimal counter.
			
xxx = UNIT ID as 3 degit hexadecimal.
			
yyyy = Year (Gregorian)
			
mm = Month (1 to 12)
			
dd = Day (1 to 31)
			
hh = Hour (0 to 23)
			
mm = Minute (0 to 59)
			
ss = Second (0 to 59)
Example:

Command:
Notification:
		
Meaning:
		

event MTX:EventLogGetLog "logindex=2"
OK event MTX:EventLogGetLog "log2=err/DCP[0] communication error// x53 on (1) ID-001
2013/1/22 11:38:23"
Query of event log at index number 2.
Event log of index no.2 is error alert no. 53.

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

48

3. Command Specifications
3-42) Query for alert event log as list
Command
event
Details:
Note:

Option 1
MTX:EventLogGetLogList

Option 2
"logindex=xxxx-xxxx"

Description
Query for event log list

xxxx-xxxx= First index number - Last index number
The range of index numbers is "0" to "total number of event logs - 1".
Use "3-40) Number of alert event log query" to get total number of event logs.

Remark: Do not allow exceed number of event log.
First index number should be less than Last index number.
One message can query up to 10 logs.
Response
Response string
Description
OK event MTX:EventLogGetLogList "logindex=x-x|log0=(AlertData)|log1=(AlertData)|…" Query for event log as list
Details:

xxxx-xxxx= First index number - Last index number
(AlertData)= "flt/message// xnnn onf (sssss) ID-xxx yyyy/mm/dd hh:mm:ss"
		 "err/message// xnnn onf (sssss) ID-xxx yyyy/mm/dd hh:mm:ss"
		 "wrn/message// xnnn onf (sssss) ID-xxx yyyy/mm/dd hh:mm:ss"
		 First 3 letter describes type of event
			 message = Alert message string - Maximum 32 letter (ascii character)
			
nnn = Alert number (same as number displayed on front panel of device)
				 - 2 or 3 digit hexadecimal.
			
onf = alert ON/OFF
				 Event of status change (e.g. wordclock unlock) sends ON when the remarkable
				 event starts, sends OFF when the event ends.
				 Momentary event (e.g. SD card player error) sends only ON when it happens.
			
sssss = counter of alarm ( Count up same Alert, normally as 1) as decimal counter.
			
xxx = UNIT ID as 3 degit hexadecimal.
			
yyyy = Year (Gregorian)
			
mm = Month (1 to 12)
			
dd = Day (1 to 31)
			
hh = Hour (0 to 23)
			
mm = Minute (0 to 59)
			
ss = Second (0 to 59)
Example:

command:
Notification:
		
Meanings:
		

event MTX:EventLogGetLogList "logindex=0-5"
OK event MTX:EventLogGetLogList logindex=0-5|log0=err/DCP[0] communication error// x53 on (1)
ID-001 2013/1/22 11:38:23|log1=flt/System error// x01 on ….
Query for list of event log of index number 0 to 5.
Alert of index number 0 to 5 is, index number 0, error alert no.53/ index number 1, error alert ….

3-43) Clear alert event log
Command
event

Option 1
MTX:EventLogClear

Option 2
""

Description
Clear event log

Response
Response string
OK event MTX:EventLogClear "lognum=0"
Example:

Command:
Notification:
Meaning:
		

Description
Number of cleared event log

event MTX:EventLogClear ""
OK event MTX:EventLogClear "lognum=0"
Clear event log
Cleared event log

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

49

3. Command Specifications

3.5. Command Errors
3.5.1. Command Error Notifications
Error notification that indicates errors in commands.
If an error is found when the command is sent, this notification is returned instead of the normal successful notification.
[Notification syntax]
Command name
Error code

ERROR  
Alphanumeric
Alphanumeric

Name of the command that caused the error
Error description
* See the error codes below.

Error code
Error code
UnknownCommand
WrongFormat

InvalidArgument

UnknownAddress
UnknownEventID
TooLongCommand
AccessDenied

Busy
ReadOnly
NoPermission
InternalError

Description
Ignored because it was an unknown command.
Ignored because the command parameter format was wrong and could not be interpreted.
Examples:
The number of parameters is wrong.
The parameter syntax is wrong.
Ignored because the command parameter content was outside the appropriate range and
could not be interpreted.
Examples:
The parameter value is outside the range.
The parameter syntax does not comply with the specifications.
The letter case of the parameter is wrong.
Ignored because the specified address does not exist.
Ignored because the specified event ID does not exist.
Could not be interpreted because the command was too long.
Procedure rejected because the peer device is not in an normal running state.
Examples:
Rejected because an ssrecall command was received in emergency run
mode.
The device is busy processing; it can’t receive commands.
Ignored because an attempt was made to set a parameter at a read-only address.
Ignored because you do not have access permission.
An internal error may have occurred.
Examples:
Failed to process the command.
Attempted to query or change the value of a parameter that does not exist
in the device.

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

50

4. Command Sequence
Below are examples of how to process remote control.
When viewed from the controller, the following major phases exist in order to perform remote control.

Start procedure

Communication start
• Wait for the device to start (devstatus)

Initial setting
• MTX external control protocol setting
(scpmode)
• Parameter syncing (get, set, etc.)

Normal procedure
• Detect operation of controls.
• Receive communication from the
device.

Normal procedure details
Detects the operation
of controls by the user.
• Operation of a parameter control
• Operation of a Snapshot or Preset

Send request commands
depending on the
operation.

•
•
•
•
•

set
setn
sett
setr
ssrecall, etc.

Information query trigger
caused by user operation
• Preset list display
• device information display

Send request commands
depending on the
necessary information.

•
•
•
•

sscurrent
ssnum
ssinfo
devinfo, etc.

Meter display is necessary.

Request periodically.

• mtrstart

• OK
• OKm
• NOTIFY

Apply changes depending on the
notification.

Control or display
• Position change
• Display change
For various events
• Parameter syncing
• Event processing

The controller designer needs to design and implement the blue items in the above figure.
The detailed sequences of various procedures are provided below.

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

51

4. Command Sequence

4.1. Communication start sequence
The amount of time for the controller and the controlled device to start is different.
Remote control is an act of controlling the controlled device from the controller, so the controller must wait for the controlled device to
become ready.
The controller needs to wait using the sequence below.
1. If an Ethernet connection is required, the remote controller needs to establish a logical session, with the MTX device(s) based
on IP address(es) and port number.
(This is not necessary for a connection that only needs to be connected physically, as in RS-232C.)
2. After the session is established, the controller sends devstatus commands at 1 second or longer intervals.
3. If "OK devstatus runmode" is returned, the controller should check the information.
4. If the controller determines that the controlled device is in normal running mode, the controller can start sending command
strings to change parameter value and preset etc. If the controlled device is not in normal running mode, the controller continues
trying.

Note:

In order to establish remote control communication, the external controller must send [devstatus runmode] command to the
device and await response. When the device responds as [OK devstatus runmode "normal"], the device is ready to receive
commands.

Time

Remote controller

Controlled device
* If the communication path is
already established, the
controller sends devstatus
runmode at 1 second or longer
intervals until a result
notification is returned.

Establish communication path to
controlled device.

devstatus runmode
devstatus runmode
devstatus runmode

1 second or longer intervals
1 second or longer intervals

........

devstatus runmode
OK devstatus runmode "normal"
Connection detected.

The controller checks the run
mode included in the result
notifications to see if the
device is ready to start remote
control communication.
The device may also actively
send change notifications, so
the controller must monitor
both result and change
notifications.

The reason for using such a sequence is provided below.
Example when the controller starts earlier than the controlled device

Remote controller

Connected physically

Controlled device

Normally running

devstatus runmode
Connection unknown
Waiting to start

devstatus runmode

Device starting

devstatus runmode
........

OK devstatus runmode "normal"

Device normal running

Connection detection

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

52

4. Command Sequence
Example when the controlled device starts earlier than the controller

Remote controller

Connected physically

Starting

Controlled device

Device starting

Device normal running

Connection unknown

devstatus runmode
OK devstatus runmode "normal"

Connection detection
* With the first devstatus runmode
request, a result notification is
returned.

Controller can recognize that Controlled device is ready to receive commands when there is response for "devstatus runmode" command.
In case of Ethernet connection, Ethernet logical session (e.g. port open) should be established before sending "devstatus runmode".

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

53

4. Command Sequence

4.2. Parameter sync sequence
Immediately after communication starts, the controller does not know anything about the most recent status of the controlled device.
Therefore, the controller must query all parameters that it plans to handle.
This also applies for when preset recall is executed, because the controller does not know how the device has changed.

Querying the most recent status of the controlled device or when a snapshot recall occurs

Remote controller

Controlled device

Normally running
Connection detection
Apply

get MTX:mem_512/60000/0/0/0/0/0 0 0

Normally running
Communication possible

OK get MTX:mem_512/60000/0/0/0/0/0 0 0 -7760

get MTX:mem_XXX/XXXXX/X/X/X/X/X X X
Apply

OK get MTX:mem_XXX/XXXXX/X/X/X/X/X X X

get MTX:mem_XXX/XXXXX/X/X/X/X/X X X
Apply

OK get MTX:mem_XXX/XXXXX/X/X/X/X/X X X

......

* Repeat get for all the necessary parameters.

Synced

Synced

Example 1: Query the DCA fader value.
get MTX:mem_512/60000/0/0/0/0/0 0 0
Query the 1ch level of the DCA fader with raw values.
OK get MTX:mem_512/60000/0/0/0/0/0 0 0 -7760
The 1ch level of the DCA fader is -77.60.
Example 2: Set the DCA fader value.
set MTX:mem_512/60000/0/0/0/0/0 0 0 -7760
Set the 1ch level of the DCA fader to a raw value of -77.60.
OK set MTX:mem_512/60000/0/0/0/0/0 0 0 -7760 "-77.60"
The 1ch level of the DCA fader was set to "-77.60".
Executing this sequence synchronizes the status with the controlled device.
However, if the controller receives a change notification from the controlled device during this query sequence, the controller needs to
query again.
Note that, as with a GPI controller made by user, if you want to apply the physical positions of the controller to the device, there is no
need to execute the above sequence.
If you want to apply the physical positions of the controller to the device immediately after a connection is established, without any user
interaction, simply use set commands to do so.

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

54

4. Command Sequence
Applying the most recent status of the controller to the device

Remote controller

Controlled device

Normally running
Connection detection
Apply

set MTX:mem_512/60000/0/0/0/0/0 0 0 -7760

Normally running
Communication possible

OK set MTX:mem_512/60000/0/0/0/0/0 0 0 -7760 "-77.60"

OK set MTX:mem_XXX/XXXXX/X/X/X/X/X X X XXXX
Apply

OK set MTX:mem_XXX/XXXXX/X/X/X/X/X X X XXXX "XXXX"

OK set MTX:mem_XXX/XXXXX/X/X/X/X/X X X XXXX
Apply

OK set MTX:mem_XXX/XXXXX/X/X/X/X/X X X XXXX "XXXX"

......

* Repeat get for all the necessary parameters.

Synced

Synced

Depending on the controller specifications, the above two sequences may be used in combination.
Example: The GPI fader uses the status of the controller, but other parameters use the status of the controlled device.

4.3. Parameter query sequence at any given time
LEDs and displays on the GUI
Indications are updated on the basis of the result notifications returned after the processing of the set commands.
Alternatively, send an explicit get request and apply the result to the indications, as shown below.

Remote controller

Controlled device

An event occurs that
calls for a value to be queried
Apply

get MTX:mem_512/XXXXX/X/X/X/X/X X X
OK get MTX:mem_512/XXXXX/X/X/X/X/X X X

One example of using this sequence would
be for refreshing the UI after boot-up or after
changing tabs.

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

55

4. Command Sequence

4.4. Meter data request/query sequence
The controller requests meter data by specifying the meter data address and the minimum transmission interval.
The meter transmission stops after 10 seconds. To continue receiving data, make another request before the 10 seconds pass.

Remote controller

Controlled device
mtrstart MTX:mtr_512/20020/level 1000

OutputLevelMeter
request

Start measuring
10 seconds

OK mtrstart MTX:mtr_512/20020/level

NOTIFY mtr MTX:mtr_512/20020/level level 71 71 ...

Apply
Request periodically
at 10 seconds or
Apply
shorter intervals

OutputLevelMeter
request

1000 ms or longer
intervals

NOTIFY mtr MTX:mtr_512/20020/level level 69 69 ...

1000 ms or longer
intervals

............

Apply

NOTIFY mtr MTX:mtr_512/20020/level level 70 70 ...

mtrstart MTX:mtr_512/20020/level 1000
Start measuring
10 seconds

OK mtrstart MTX:mtr_512/20020/level

* Transmission for 10 seconds after a request
If another request is received, restart measuring the time.

4.5. Preset recall request sequence
Upon receiving a result notification in response to a Preset Recall request, you need to execute the parameter sync sequence.

Remote controller

Remote control
To the parameter
sync sequence

Controlled device
ssrecall 10
OK ssrecall 10

In addition, if a Preset recall occurs internally in the controlled device (e.g. by front panel button press) or when such a request is
received from another controller, the controller receives a change notification that indicates that all parameters have changed (see the
next section). If this occurs, the controller needs to execute the parameter sync sequence.

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

56

4. Command Sequence

4.6. Sequence when parameters are changed by another controller
If the controller sends a parameter set request, a change notification is returned immediately.
However, if parameters change internally in the controlled device (this includes changes in parameters that occur as a result of a
controller operation on another parameter) or due to a request from another controller, a parameter change notification is received, as
shown below.
The controller receiving a parameter change notification updates its own status if necessary.

Remote controller

Apply parameter changes
or proceed to the
parameter sync sequence

Controlled device
NOTIFY ...
Sampled
parameter
changes

Recall operation or
parameter change
by the controlled device
or another controller

The way in which parameter change notifications are sent varies depending on the value notification mode specified in the MTX external
control protocol mode.

Advice for choosing normalized/raw value mode.
If you want to handle a value with a given range, such as in an MIDI controller,
• Set the value notification mode to normalized value notification mode, and specify the required resolution.
• Use setn/getn to perform processing from the controller.
• Apply changes to the controller according to NOTIFY setn.
Conversely, for a highly functional PC application where you want to use all the internal parameters,
• Set the MTX external control protocol mode to raw value mode.
• Use set/get to perform processing from the controller.
• Apply changes to the controller according to NOTIFY set.
• Use setn/getn for certain parameters when necessary.

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

57

5. Meter Value
Level Meter, Hold Meter, GR Meter
Value
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
NOTE:

Data
-126dBFS or less
-125dBFS
-124dBFS
-123dBFS
-122dBFS
-121dBFS
-120dBFS
-119dBFS
-118dBFS
-117dBFS
-116dBFS
-115dBFS
-114dBFS
-113dBFS
-112dBFS
-111dBFS
-110dBFS
-109dBFS
-108dBFS
-107dBFS
-106dBFS
-105dBFS
-104dBFS
-103dBFS
-102dBFS
-101dBFS
-100dBFS
-99dBFS
-98dBFS
-97dBFS
-96dBFS
-95dBFS

Value
20
21
22
23
24
25
26
27
28
29
2A
2B
2C
2D
2E
2F
30
31
32
33
34
35
36
37
38
39
3A
3B
3C
3D
3E
3F

Data
-94dBFS
-93dBFS
-92dBFS
-91dBFS
-90dBFS
-89dBFS
-88dBFS
-87dBFS
-86dBFS
-85dBFS
-84dBFS
-83dBFS
-82dBFS
-81dBFS
-80dBFS
-79dBFS
-78dBFS
-77dBFS
-76dBFS
-75dBFS
-74dBFS
-73dBFS
-72dBFS
-71dBFS
-70dBFS
-69dBFS
-68dBFS
-67dBFS
-66dBFS
-65dBFS
-64dBFS
-63dBFS

Value
40
41
42
43
44
45
46
47
48
49
4A
4B
4C
4D
4E
4F
50
51
52
55
54
55
56
57
58
59
5A
5B
5C
5D
5E
5F

Data
-62dBFS
-61dBFS
-60dBFS
-59dBFS
-58dBFS
-57dBFS
-56dBFS
-55dBFS
-54dBFS
-53dBFS
-52dBFS
-51dBFS
-50dBFS
-49dBFS
-48dBFS
-47dBFS
-46dBFS
-45dBFS
-44dBFS
-43dBFS
-42dBFS
-41dBFS
-40dBFS
-39dBFS
-38dBFS
-37dBFS
-36dBFS
-35dBFS
-34dBFS
-33dBFS
-32dBFS
-31dBFS

Value
60
61
62
63
66
65
66
67
68
69
6A
6B
6C
6D
6E
6F
70
71
72
77
74
77
76
77
78
79
7A
7B
7C
7D
7E
7F

Data
-30dBFS
-29dBFS
-28dBFS
-27dBFS
-26dBFS
-25dBFS
-24dBFS
-23dBFS
-22dBFS
-21dBFS
-20dBFS
-19dBFS
-18dBFS
-17dBFS
-16dBFS
-15dBFS
-14dBFS
-13dBFS
-12dBFS
-11dBFS
-10dBFS
-9dBFS
-8dBFS
-7dBFS
-6dBFS
-5dBFS
-4dBFS
-3dBFS
-2dBFS
-1dBFS
0dBFS
OVER

A device may not be able to send all the values depending on how precise the device processes values internally.

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

58

6. Parameter Value Details
6.1. Fader parameter
6.1.1. Fader with "-Infinity to 0dB" range
Value
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63

Data
-InfdB
-138.00dB
-136.00dB
-134.00dB
-133.00dB
-132.00dB
-131.00dB
-130.00dB
-129.00dB
-128.00dB
-127.00dB
-126.00dB
-125.00dB
-124.00dB
-123.00dB
-122.00dB
-121.00dB
-120.00dB
-119.00dB
-118.00dB
-117.00dB
-116.00dB
-115.00dB
-114.00dB
-113.00dB
-112.00dB
-111.00dB
-110.00dB
-109.00dB
-108.00dB
-107.00dB
-106.00dB
-105.00dB
-104.00dB
-103.00dB
-102.00dB
-101.50dB
-101.00dB
-100.50dB
-100.00dB
-99.50dB
-99.00dB
-98.50dB
-98.00dB
-97.50dB
-97.00dB
-96.50dB
-96.00dB
-95.50dB
-95.00dB
-94.50dB
-94.00dB
-93.50dB
-93.00dB
-92.50dB
-92.00dB
-91.50dB
-91.00dB
-90.50dB
-90.00dB
-89.50dB
-89.00dB
-88.50dB
-88.00dB

Value
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127

Data
-87.50dB
-87.00dB
-86.50dB
-86.00dB
-85.50dB
-85.00dB
-84.50dB
-84.00dB
-83.50dB
-83.00dB
-82.50dB
-82.00dB
-81.50dB
-81.00dB
-80.50dB
-80.00dB
-79.50dB
-79.00dB
-78.50dB
-78.00dB
-77.80dB
-77.60dB
-77.40dB
-77.20dB
-77.00dB
-76.80dB
-76.60dB
-76.40dB
-76.20dB
-76.00dB
-75.80dB
-75.60dB
-75.40dB
-75.20dB
-75.00dB
-74.80dB
-74.60dB
-74.40dB
-74.20dB
-74.00dB
-73.80dB
-73.60dB
-73.40dB
-73.20dB
-73.00dB
-72.80dB
-72.60dB
-72.40dB
-72.20dB
-72.00dB
-71.80dB
-71.60dB
-71.40dB
-71.20dB
-71.00dB
-70.80dB
-70.60dB
-70.40dB
-70.20dB
-70.00dB
-69.80dB
-69.60dB
-69.40dB
-69.20dB

Value
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191

Data
-69.00dB
-68.80dB
-68.60dB
-68.40dB
-68.20dB
-68.00dB
-67.80dB
-67.60dB
-67.40dB
-67.20dB
-67.00dB
-66.80dB
-66.60dB
-66.40dB
-66.20dB
-66.00dB
-65.80dB
-65.60dB
-65.40dB
-65.20dB
-65.00dB
-64.80dB
-64.60dB
-64.40dB
-64.20dB
-64.00dB
-63.80dB
-63.60dB
-63.40dB
-63.20dB
-63.00dB
-62.80dB
-62.60dB
-62.40dB
-62.20dB
-62.00dB
-61.80dB
-61.60dB
-61.40dB
-61.20dB
-61.00dB
-60.80dB
-60.60dB
-60.40dB
-60.20dB
-60.00dB
-59.80dB
-59.60dB
-59.40dB
-59.20dB
-59.00dB
-58.80dB
-58.60dB
-58.40dB
-58.20dB
-58.00dB
-57.80dB
-57.60dB
-57.40dB
-57.20dB
-57.00dB
-56.80dB
-56.60dB
-56.40dB

Value
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255

Data
-56.20dB
-56.00dB
-55.80dB
-55.60dB
-55.40dB
-55.20dB
-55.00dB
-54.80dB
-54.60dB
-54.40dB
-54.20dB
-54.00dB
-53.80dB
-53.60dB
-53.40dB
-53.20dB
-53.00dB
-52.80dB
-52.60dB
-52.40dB
-52.20dB
-52.00dB
-51.80dB
-51.60dB
-51.40dB
-51.20dB
-51.00dB
-50.80dB
-50.60dB
-50.40dB
-50.20dB
-50.00dB
-49.90dB
-49.80dB
-49.70dB
-49.60dB
-49.50dB
-49.40dB
-49.30dB
-49.20dB
-49.10dB
-49.00dB
-48.90dB
-48.80dB
-48.70dB
-48.60dB
-48.50dB
-48.40dB
-48.30dB
-48.20dB
-48.10dB
-48.00dB
-47.90dB
-47.80dB
-47.70dB
-47.60dB
-47.50dB
-47.40dB
-47.30dB
-47.20dB
-47.10dB
-47.00dB
-46.90dB
-46.80dB

Value
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319

Data
-46.70dB
-46.60dB
-46.50dB
-46.40dB
-46.30dB
-46.20dB
-46.10dB
-46.00dB
-45.90dB
-45.80dB
-45.70dB
-45.60dB
-45.50dB
-45.40dB
-45.30dB
-45.20dB
-45.10dB
-45.00dB
-44.90dB
-44.80dB
-44.70dB
-44.60dB
-44.50dB
-44.40dB
-44.30dB
-44.20dB
-44.10dB
-44.00dB
-43.90dB
-43.80dB
-43.70dB
-43.60dB
-43.50dB
-43.40dB
-43.30dB
-43.20dB
-43.10dB
-43.00dB
-42.90dB
-42.80dB
-42.70dB
-42.60dB
-42.50dB
-42.40dB
-42.30dB
-42.20dB
-42.10dB
-42.00dB
-41.90dB
-41.80dB
-41.70dB
-41.60dB
-41.50dB
-41.40dB
-41.30dB
-41.20dB
-41.10dB
-41.00dB
-40.90dB
-40.80dB
-40.70dB
-40.60dB
-40.50dB
-40.40dB

Value
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383

Data
-40.30dB
-40.20dB
-40.10dB
-40.00dB
-39.90dB
-39.80dB
-39.70dB
-39.60dB
-39.50dB
-39.40dB
-39.30dB
-39.20dB
-39.10dB
-39.00dB
-38.90dB
-38.80dB
-38.70dB
-38.60dB
-38.50dB
-38.40dB
-38.30dB
-38.20dB
-38.10dB
-38.00dB
-37.90dB
-37.80dB
-37.70dB
-37.60dB
-37.50dB
-37.40dB
-37.30dB
-37.20dB
-37.10dB
-37.00dB
-36.90dB
-36.80dB
-36.70dB
-36.60dB
-36.50dB
-36.40dB
-36.30dB
-36.20dB
-36.10dB
-36.00dB
-35.90dB
-35.80dB
-35.70dB
-35.60dB
-35.50dB
-35.40dB
-35.30dB
-35.20dB
-35.10dB
-35.00dB
-34.90dB
-34.80dB
-34.70dB
-34.60dB
-34.50dB
-34.40dB
-34.30dB
-34.20dB
-34.10dB
-34.00dB

Value
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447

Data
-33.90dB
-33.80dB
-33.70dB
-33.60dB
-33.50dB
-33.40dB
-33.30dB
-33.20dB
-33.10dB
-33.00dB
-32.90dB
-32.80dB
-32.70dB
-32.60dB
-32.50dB
-32.40dB
-32.30dB
-32.20dB
-32.10dB
-32.00dB
-31.90dB
-31.80dB
-31.70dB
-31.60dB
-31.50dB
-31.40dB
-31.30dB
-31.20dB
-31.10dB
-31.00dB
-30.90dB
-30.80dB
-30.70dB
-30.60dB
-30.50dB
-30.40dB
-30.30dB
-30.20dB
-30.10dB
-30.00dB
-29.95dB
-29.90dB
-29.85dB
-29.80dB
-29.75dB
-29.70dB
-29.65dB
-29.60dB
-29.55dB
-29.50dB
-29.45dB
-29.40dB
-29.35dB
-29.30dB
-29.25dB
-29.20dB
-29.15dB
-29.10dB
-29.05dB
-29.00dB
-28.95dB
-28.90dB
-28.85dB
-28.80dB

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

Value
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511

Data
-28.75dB
-28.70dB
-28.65dB
-28.60dB
-28.55dB
-28.50dB
-28.45dB
-28.40dB
-28.35dB
-28.30dB
-28.25dB
-28.20dB
-28.15dB
-28.10dB
-28.05dB
-28.00dB
-27.95dB
-27.90dB
-27.85dB
-27.80dB
-27.75dB
-27.70dB
-27.65dB
-27.60dB
-27.55dB
-27.50dB
-27.45dB
-27.40dB
-27.35dB
-27.30dB
-27.25dB
-27.20dB
-27.15dB
-27.10dB
-27.05dB
-27.00dB
-26.95dB
-26.90dB
-26.85dB
-26.80dB
-26.75dB
-26.70dB
-26.65dB
-26.60dB
-26.55dB
-26.50dB
-26.45dB
-26.40dB
-26.35dB
-26.30dB
-26.25dB
-26.20dB
-26.15dB
-26.10dB
-26.05dB
-26.00dB
-25.95dB
-25.90dB
-25.85dB
-25.80dB
-25.75dB
-25.70dB
-25.65dB
-25.60dB

59

6. Parameter Value Details
Value
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575

Data
-25.55dB
-25.50dB
-25.45dB
-25.40dB
-25.35dB
-25.30dB
-25.25dB
-25.20dB
-25.15dB
-25.10dB
-25.05dB
-25.00dB
-24.95dB
-24.90dB
-24.85dB
-24.80dB
-24.75dB
-24.70dB
-24.65dB
-24.60dB
-24.55dB
-24.50dB
-24.45dB
-24.40dB
-24.35dB
-24.30dB
-24.25dB
-24.20dB
-24.15dB
-24.10dB
-24.05dB
-24.00dB
-23.95dB
-23.90dB
-23.85dB
-23.80dB
-23.75dB
-23.70dB
-23.65dB
-23.60dB
-23.55dB
-23.50dB
-23.45dB
-23.40dB
-23.35dB
-23.30dB
-23.25dB
-23.20dB
-23.15dB
-23.10dB
-23.05dB
-23.00dB
-22.95dB
-22.90dB
-22.85dB
-22.80dB
-22.75dB
-22.70dB
-22.65dB
-22.60dB
-22.55dB
-22.50dB
-22.45dB
-22.40dB

Value
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639

Data
-22.35dB
-22.30dB
-22.25dB
-22.20dB
-22.15dB
-22.10dB
-22.05dB
-22.00dB
-21.95dB
-21.90dB
-21.85dB
-21.80dB
-21.75dB
-21.70dB
-21.65dB
-21.60dB
-21.55dB
-21.50dB
-21.45dB
-21.40dB
-21.35dB
-21.30dB
-21.25dB
-21.20dB
-21.15dB
-21.10dB
-21.05dB
-21.00dB
-20.95dB
-20.90dB
-20.85dB
-20.80dB
-20.75dB
-20.70dB
-20.65dB
-20.60dB
-20.55dB
-20.50dB
-20.45dB
-20.40dB
-20.35dB
-20.30dB
-20.25dB
-20.20dB
-20.15dB
-20.10dB
-20.05dB
-20.00dB
-19.95dB
-19.90dB
-19.85dB
-19.80dB
-19.75dB
-19.70dB
-19.65dB
-19.60dB
-19.55dB
-19.50dB
-19.45dB
-19.40dB
-19.35dB
-19.30dB
-19.25dB
-19.20dB

Value
640
641
642
643
644
645
646
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
664
665
666
667
668
669
670
671
672
673
674
675
676
677
678
679
680
681
682
683
684
685
686
687
688
689
690
691
692
693
694
695
696
697
698
699
700
701
702
703

Data
-19.15dB
-19.10dB
-19.05dB
-19.00dB
-18.95dB
-18.90dB
-18.85dB
-18.80dB
-18.75dB
-18.70dB
-18.65dB
-18.60dB
-18.55dB
-18.50dB
-18.45dB
-18.40dB
-18.35dB
-18.30dB
-18.25dB
-18.20dB
-18.15dB
-18.10dB
-18.05dB
-18.00dB
-17.95dB
-17.90dB
-17.85dB
-17.80dB
-17.75dB
-17.70dB
-17.65dB
-17.60dB
-17.55dB
-17.50dB
-17.45dB
-17.40dB
-17.35dB
-17.30dB
-17.25dB
-17.20dB
-17.15dB
-17.10dB
-17.05dB
-17.00dB
-16.95dB
-16.90dB
-16.85dB
-16.80dB
-16.75dB
-16.70dB
-16.65dB
-16.60dB
-16.55dB
-16.50dB
-16.45dB
-16.40dB
-16.35dB
-16.30dB
-16.25dB
-16.20dB
-16.15dB
-16.10dB
-16.05dB
-16.00dB

Value
704
705
706
707
708
709
710
711
712
713
714
715
716
717
718
719
720
721
722
723
724
725
726
727
728
729
730
731
732
733
734
735
736
737
738
739
740
741
742
743
744
745
746
747
748
749
750
751
752
753
754
755
756
757
758
759
760
761
762
763
764
765
766
767

Data
-15.95dB
-15.90dB
-15.85dB
-15.80dB
-15.75dB
-15.70dB
-15.65dB
-15.60dB
-15.55dB
-15.50dB
-15.45dB
-15.40dB
-15.35dB
-15.30dB
-15.25dB
-15.20dB
-15.15dB
-15.10dB
-15.05dB
-15.00dB
-14.95dB
-14.90dB
-14.85dB
-14.80dB
-14.75dB
-14.70dB
-14.65dB
-14.60dB
-14.55dB
-14.50dB
-14.45dB
-14.40dB
-14.35dB
-14.30dB
-14.25dB
-14.20dB
-14.15dB
-14.10dB
-14.05dB
-14.00dB
-13.95dB
-13.90dB
-13.85dB
-13.80dB
-13.75dB
-13.70dB
-13.65dB
-13.60dB
-13.55dB
-13.50dB
-13.45dB
-13.40dB
-13.35dB
-13.30dB
-13.25dB
-13.20dB
-13.15dB
-13.10dB
-13.05dB
-13.00dB
-12.95dB
-12.90dB
-12.85dB
-12.80dB

Value
768
769
770
771
772
773
774
775
776
777
778
779
780
781
782
783
784
785
786
787
788
789
790
791
792
793
794
795
796
797
798
799
800
801
802
803
804
805
806
807
808
809
810
811
812
813
814
815
816
817
818
819
820
821
822
823
824
825
826
827
828
829
830
831

Data
-12.75dB
-12.70dB
-12.65dB
-12.60dB
-12.55dB
-12.50dB
-12.45dB
-12.40dB
-12.35dB
-12.30dB
-12.25dB
-12.20dB
-12.15dB
-12.10dB
-12.05dB
-12.00dB
-11.95dB
-11.90dB
-11.85dB
-11.80dB
-11.75dB
-11.70dB
-11.65dB
-11.60dB
-11.55dB
-11.50dB
-11.45dB
-11.40dB
-11.35dB
-11.30dB
-11.25dB
-11.20dB
-11.15dB
-11.10dB
-11.05dB
-11.00dB
-10.95dB
-10.90dB
-10.85dB
-10.80dB
-10.75dB
-10.70dB
-10.65dB
-10.60dB
-10.55dB
-10.50dB
-10.45dB
-10.40dB
-10.35dB
-10.30dB
-10.25dB
-10.20dB
-10.15dB
-10.10dB
-10.05dB
-10.00dB
-9.95dB
-9.90dB
-9.85dB
-9.80dB
-9.75dB
-9.70dB
-9.65dB
-9.60dB

Value
832
833
834
835
836
837
838
839
840
841
842
843
844
845
846
847
848
849
850
851
852
853
854
855
856
857
858
859
860
861
862
863
864
865
866
867
868
869
870
871
872
873
874
875
876
877
878
879
880
881
882
883
884
885
886
887
888
889
890
891
892
893
894
895

Data
-9.55dB
-9.50dB
-9.45dB
-9.40dB
-9.35dB
-9.30dB
-9.25dB
-9.20dB
-9.15dB
-9.10dB
-9.05dB
-9.00dB
-8.95dB
-8.90dB
-8.85dB
-8.80dB
-8.75dB
-8.70dB
-8.65dB
-8.60dB
-8.55dB
-8.50dB
-8.45dB
-8.40dB
-8.35dB
-8.30dB
-8.25dB
-8.20dB
-8.15dB
-8.10dB
-8.05dB
-8.00dB
-7.95dB
-7.90dB
-7.85dB
-7.80dB
-7.75dB
-7.70dB
-7.65dB
-7.60dB
-7.55dB
-7.50dB
-7.45dB
-7.40dB
-7.35dB
-7.30dB
-7.25dB
-7.20dB
-7.15dB
-7.10dB
-7.05dB
-7.00dB
-6.95dB
-6.90dB
-6.85dB
-6.80dB
-6.75dB
-6.70dB
-6.65dB
-6.60dB
-6.55dB
-6.50dB
-6.45dB
-6.40dB

Value
896
897
898
899
900
901
902
903
904
905
906
907
908
909
910
911
912
913
914
915
916
917
918
919
920
921
922
923
924
925
926
927
928
929
930
931
932
933
934
935
936
937
938
939
940
941
942
943
944
945
946
947
948
949
950
951
952
953
954
955
956
957
958
959

Data
-6.35dB
-6.30dB
-6.25dB
-6.20dB
-6.15dB
-6.10dB
-6.05dB
-6.00dB
-5.95dB
-5.90dB
-5.85dB
-5.80dB
-5.75dB
-5.70dB
-5.65dB
-5.60dB
-5.55dB
-5.50dB
-5.45dB
-5.40dB
-5.35dB
-5.30dB
-5.25dB
-5.20dB
-5.15dB
-5.10dB
-5.05dB
-5.00dB
-4.95dB
-4.90dB
-4.85dB
-4.80dB
-4.75dB
-4.70dB
-4.65dB
-4.60dB
-4.55dB
-4.50dB
-4.45dB
-4.40dB
-4.35dB
-4.30dB
-4.25dB
-4.20dB
-4.15dB
-4.10dB
-4.05dB
-4.00dB
-3.95dB
-3.90dB
-3.85dB
-3.80dB
-3.75dB
-3.70dB
-3.65dB
-3.60dB
-3.55dB
-3.50dB
-3.45dB
-3.40dB
-3.35dB
-3.30dB
-3.25dB
-3.20dB

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

Value
960
961
962
963
964
965
966
967
968
969
970
971
972
973
974
975
976
977
978
979
980
981
982
983
984
985
986
987
988
989
990
991
992
993
994
995
996
997
998
999
1000
1001
1002
1003
1004
1005
1006
1007
1008
1009
1010
1011
1012
1013
1014
1015
1016
1017
1018
1019
1020
1021
1022
1023

Data
-3.15dB
-3.10dB
-3.05dB
-3.00dB
-2.95dB
-2.90dB
-2.85dB
-2.80dB
-2.75dB
-2.70dB
-2.65dB
-2.60dB
-2.55dB
-2.50dB
-2.45dB
-2.40dB
-2.35dB
-2.30dB
-2.25dB
-2.20dB
-2.15dB
-2.10dB
-2.05dB
-2.00dB
-1.95dB
-1.90dB
-1.85dB
-1.80dB
-1.75dB
-1.70dB
-1.65dB
-1.60dB
-1.55dB
-1.50dB
-1.45dB
-1.40dB
-1.35dB
-1.30dB
-1.25dB
-1.20dB
-1.15dB
-1.10dB
-1.05dB
-1.00dB
-0.95dB
-0.90dB
-0.85dB
-0.80dB
-0.75dB
-0.70dB
-0.65dB
-0.60dB
-0.55dB
-0.50dB
-0.45dB
-0.40dB
-0.35dB
-0.30dB
-0.25dB
-0.20dB
-0.15dB
-0.10dB
-0.05dB
0.00dB

60

6. Parameter Value Details
6.1.2. Fader with "-Infinity to 10dB" range
Value
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63

Data
-InfdB
-138.00dB
-135.00dB
-132.00dB
-129.00dB
-126.00dB
-123.00dB
-120.00dB
-117.00dB
-114.00dB
-111.00dB
-108.00dB
-105.00dB
-102.00dB
-99.00dB
-96.00dB
-95.00dB
-94.00dB
-93.00dB
-92.00dB
-91.00dB
-90.00dB
-89.00dB
-88.00dB
-87.00dB
-86.00dB
-85.00dB
-84.00dB
-83.00dB
-82.00dB
-81.00dB
-80.00dB
-79.00dB
-78.00dB
-77.80dB
-77.60dB
-77.40dB
-77.20dB
-77.00dB
-76.80dB
-76.60dB
-76.40dB
-76.20dB
-76.00dB
-75.80dB
-75.60dB
-75.40dB
-75.20dB
-75.00dB
-74.80dB
-74.60dB
-74.40dB
-74.20dB
-74.00dB
-73.80dB
-73.60dB
-73.40dB
-73.20dB
-73.00dB
-72.80dB
-72.60dB
-72.40dB
-72.20dB
-72.00dB

Value
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127

Data
-71.80dB
-71.60dB
-71.40dB
-71.20dB
-71.00dB
-70.80dB
-70.60dB
-70.40dB
-70.20dB
-70.00dB
-69.80dB
-69.60dB
-69.40dB
-69.20dB
-69.00dB
-68.80dB
-68.60dB
-68.40dB
-68.20dB
-68.00dB
-67.80dB
-67.60dB
-67.40dB
-67.20dB
-67.00dB
-66.80dB
-66.60dB
-66.40dB
-66.20dB
-66.00dB
-65.80dB
-65.60dB
-65.40dB
-65.20dB
-65.00dB
-64.80dB
-64.60dB
-64.40dB
-64.20dB
-64.00dB
-63.80dB
-63.60dB
-63.40dB
-63.20dB
-63.00dB
-62.80dB
-62.60dB
-62.40dB
-62.20dB
-62.00dB
-61.80dB
-61.60dB
-61.40dB
-61.20dB
-61.00dB
-60.80dB
-60.60dB
-60.40dB
-60.20dB
-60.00dB
-59.80dB
-59.60dB
-59.40dB
-59.20dB

Value
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191

Data
-59.00dB
-58.80dB
-58.60dB
-58.40dB
-58.20dB
-58.00dB
-57.80dB
-57.60dB
-57.40dB
-57.20dB
-57.00dB
-56.80dB
-56.60dB
-56.40dB
-56.20dB
-56.00dB
-55.80dB
-55.60dB
-55.40dB
-55.20dB
-55.00dB
-54.80dB
-54.60dB
-54.40dB
-54.20dB
-54.00dB
-53.80dB
-53.60dB
-53.40dB
-53.20dB
-53.00dB
-52.80dB
-52.60dB
-52.40dB
-52.20dB
-52.00dB
-51.80dB
-51.60dB
-51.40dB
-51.20dB
-51.00dB
-50.80dB
-50.60dB
-50.40dB
-50.20dB
-50.00dB
-49.80dB
-49.60dB
-49.40dB
-49.20dB
-49.00dB
-48.80dB
-48.60dB
-48.40dB
-48.20dB
-48.00dB
-47.80dB
-47.60dB
-47.40dB
-47.20dB
-47.00dB
-46.80dB
-46.60dB
-46.40dB

Value
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255

Data
-46.20dB
-46.00dB
-45.80dB
-45.60dB
-45.40dB
-45.20dB
-45.00dB
-44.80dB
-44.60dB
-44.40dB
-44.20dB
-44.00dB
-43.80dB
-43.60dB
-43.40dB
-43.20dB
-43.00dB
-42.80dB
-42.60dB
-42.40dB
-42.20dB
-42.00dB
-41.80dB
-41.60dB
-41.40dB
-41.20dB
-41.00dB
-40.80dB
-40.60dB
-40.40dB
-40.20dB
-40.00dB
-39.90dB
-39.80dB
-39.70dB
-39.60dB
-39.50dB
-39.40dB
-39.30dB
-39.20dB
-39.10dB
-39.00dB
-38.90dB
-38.80dB
-38.70dB
-38.60dB
-38.50dB
-38.40dB
-38.30dB
-38.20dB
-38.10dB
-38.00dB
-37.90dB
-37.80dB
-37.70dB
-37.60dB
-37.50dB
-37.40dB
-37.30dB
-37.20dB
-37.10dB
-37.00dB
-36.90dB
-36.80dB

Value
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319

Data
-36.70dB
-36.60dB
-36.50dB
-36.40dB
-36.30dB
-36.20dB
-36.10dB
-36.00dB
-35.90dB
-35.80dB
-35.70dB
-35.60dB
-35.50dB
-35.40dB
-35.30dB
-35.20dB
-35.10dB
-35.00dB
-34.90dB
-34.80dB
-34.70dB
-34.60dB
-34.50dB
-34.40dB
-34.30dB
-34.20dB
-34.10dB
-34.00dB
-33.90dB
-33.80dB
-33.70dB
-33.60dB
-33.50dB
-33.40dB
-33.30dB
-33.20dB
-33.10dB
-33.00dB
-32.90dB
-32.80dB
-32.70dB
-32.60dB
-32.50dB
-32.40dB
-32.30dB
-32.20dB
-32.10dB
-32.00dB
-31.90dB
-31.80dB
-31.70dB
-31.60dB
-31.50dB
-31.40dB
-31.30dB
-31.20dB
-31.10dB
-31.00dB
-30.90dB
-30.80dB
-30.70dB
-30.60dB
-30.50dB
-30.40dB

Value
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383

Data
-30.30dB
-30.20dB
-30.10dB
-30.00dB
-29.90dB
-29.80dB
-29.70dB
-29.60dB
-29.50dB
-29.40dB
-29.30dB
-29.20dB
-29.10dB
-29.00dB
-28.90dB
-28.80dB
-28.70dB
-28.60dB
-28.50dB
-28.40dB
-28.30dB
-28.20dB
-28.10dB
-28.00dB
-27.90dB
-27.80dB
-27.70dB
-27.60dB
-27.50dB
-27.40dB
-27.30dB
-27.20dB
-27.10dB
-27.00dB
-26.90dB
-26.80dB
-26.70dB
-26.60dB
-26.50dB
-26.40dB
-26.30dB
-26.20dB
-26.10dB
-26.00dB
-25.90dB
-25.80dB
-25.70dB
-25.60dB
-25.50dB
-25.40dB
-25.30dB
-25.20dB
-25.10dB
-25.00dB
-24.90dB
-24.80dB
-24.70dB
-24.60dB
-24.50dB
-24.40dB
-24.30dB
-24.20dB
-24.10dB
-24.00dB

Value
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447

Data
-23.90dB
-23.80dB
-23.70dB
-23.60dB
-23.50dB
-23.40dB
-23.30dB
-23.20dB
-23.10dB
-23.00dB
-22.90dB
-22.80dB
-22.70dB
-22.60dB
-22.50dB
-22.40dB
-22.30dB
-22.20dB
-22.10dB
-22.00dB
-21.90dB
-21.80dB
-21.70dB
-21.60dB
-21.50dB
-21.40dB
-21.30dB
-21.20dB
-21.10dB
-21.00dB
-20.90dB
-20.80dB
-20.70dB
-20.60dB
-20.50dB
-20.40dB
-20.30dB
-20.20dB
-20.10dB
-20.00dB
-19.95dB
-19.90dB
-19.85dB
-19.80dB
-19.75dB
-19.70dB
-19.65dB
-19.60dB
-19.55dB
-19.50dB
-19.45dB
-19.40dB
-19.35dB
-19.30dB
-19.25dB
-19.20dB
-19.15dB
-19.10dB
-19.05dB
-19.00dB
-18.95dB
-18.90dB
-18.85dB
-18.80dB

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

Value
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511

Data
-18.75dB
-18.70dB
-18.65dB
-18.60dB
-18.55dB
-18.50dB
-18.45dB
-18.40dB
-18.35dB
-18.30dB
-18.25dB
-18.20dB
-18.15dB
-18.10dB
-18.05dB
-18.00dB
-17.95dB
-17.90dB
-17.85dB
-17.80dB
-17.75dB
-17.70dB
-17.65dB
-17.60dB
-17.55dB
-17.50dB
-17.45dB
-17.40dB
-17.35dB
-17.30dB
-17.25dB
-17.20dB
-17.15dB
-17.10dB
-17.05dB
-17.00dB
-16.95dB
-16.90dB
-16.85dB
-16.80dB
-16.75dB
-16.70dB
-16.65dB
-16.60dB
-16.55dB
-16.50dB
-16.45dB
-16.40dB
-16.35dB
-16.30dB
-16.25dB
-16.20dB
-16.15dB
-16.10dB
-16.05dB
-16.00dB
-15.95dB
-15.90dB
-15.85dB
-15.80dB
-15.75dB
-15.70dB
-15.65dB
-15.60dB

61

6. Parameter Value Details
Value
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575

Data
-15.55dB
-15.50dB
-15.45dB
-15.40dB
-15.35dB
-15.30dB
-15.25dB
-15.20dB
-15.15dB
-15.10dB
-15.05dB
-15.00dB
-14.95dB
-14.90dB
-14.85dB
-14.80dB
-14.75dB
-14.70dB
-14.65dB
-14.60dB
-14.55dB
-14.50dB
-14.45dB
-14.40dB
-14.35dB
-14.30dB
-14.25dB
-14.20dB
-14.15dB
-14.10dB
-14.05dB
-14.00dB
-13.95dB
-13.90dB
-13.85dB
-13.80dB
-13.75dB
-13.70dB
-13.65dB
-13.60dB
-13.55dB
-13.50dB
-13.45dB
-13.40dB
-13.35dB
-13.30dB
-13.25dB
-13.20dB
-13.15dB
-13.10dB
-13.05dB
-13.00dB
-12.95dB
-12.90dB
-12.85dB
-12.80dB
-12.75dB
-12.70dB
-12.65dB
-12.60dB
-12.55dB
-12.50dB
-12.45dB
-12.40dB

Value
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639

Data
-12.35dB
-12.30dB
-12.25dB
-12.20dB
-12.15dB
-12.10dB
-12.05dB
-12.00dB
-11.95dB
-11.90dB
-11.85dB
-11.80dB
-11.75dB
-11.70dB
-11.65dB
-11.60dB
-11.55dB
-11.50dB
-11.45dB
-11.40dB
-11.35dB
-11.30dB
-11.25dB
-11.20dB
-11.15dB
-11.10dB
-11.05dB
-11.00dB
-10.95dB
-10.90dB
-10.85dB
-10.80dB
-10.75dB
-10.70dB
-10.65dB
-10.60dB
-10.55dB
-10.50dB
-10.45dB
-10.40dB
-10.35dB
-10.30dB
-10.25dB
-10.20dB
-10.15dB
-10.10dB
-10.05dB
-10.00dB
-9.95dB
-9.90dB
-9.85dB
-9.80dB
-9.75dB
-9.70dB
-9.65dB
-9.60dB
-9.55dB
-9.50dB
-9.45dB
-9.40dB
-9.35dB
-9.30dB
-9.25dB
-9.20dB

Value
640
641
642
643
644
645
646
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
664
665
666
667
668
669
670
671
672
673
674
675
676
677
678
679
680
681
682
683
684
685
686
687
688
689
690
691
692
693
694
695
696
697
698
699
700
701
702
703

Data
-9.15dB
-9.10dB
-9.05dB
-9.00dB
-8.95dB
-8.90dB
-8.85dB
-8.80dB
-8.75dB
-8.70dB
-8.65dB
-8.60dB
-8.55dB
-8.50dB
-8.45dB
-8.40dB
-8.35dB
-8.30dB
-8.25dB
-8.20dB
-8.15dB
-8.10dB
-8.05dB
-8.00dB
-7.95dB
-7.90dB
-7.85dB
-7.80dB
-7.75dB
-7.70dB
-7.65dB
-7.60dB
-7.55dB
-7.50dB
-7.45dB
-7.40dB
-7.35dB
-7.30dB
-7.25dB
-7.20dB
-7.15dB
-7.10dB
-7.05dB
-7.00dB
-6.95dB
-6.90dB
-6.85dB
-6.80dB
-6.75dB
-6.70dB
-6.65dB
-6.60dB
-6.55dB
-6.50dB
-6.45dB
-6.40dB
-6.35dB
-6.30dB
-6.25dB
-6.20dB
-6.15dB
-6.10dB
-6.05dB
-6.00dB

Value
704
705
706
707
708
709
710
711
712
713
714
715
716
717
718
719
720
721
722
723
724
725
726
727
728
729
730
731
732
733
734
735
736
737
738
739
740
741
742
743
744
745
746
747
748
749
750
751
752
753
754
755
756
757
758
759
760
761
762
763
764
765
766
767

Data
-5.95dB
-5.90dB
-5.85dB
-5.80dB
-5.75dB
-5.70dB
-5.65dB
-5.60dB
-5.55dB
-5.50dB
-5.45dB
-5.40dB
-5.35dB
-5.30dB
-5.25dB
-5.20dB
-5.15dB
-5.10dB
-5.05dB
-5.00dB
-4.95dB
-4.90dB
-4.85dB
-4.80dB
-4.75dB
-4.70dB
-4.65dB
-4.60dB
-4.55dB
-4.50dB
-4.45dB
-4.40dB
-4.35dB
-4.30dB
-4.25dB
-4.20dB
-4.15dB
-4.10dB
-4.05dB
-4.00dB
-3.95dB
-3.90dB
-3.85dB
-3.80dB
-3.75dB
-3.70dB
-3.65dB
-3.60dB
-3.55dB
-3.50dB
-3.45dB
-3.40dB
-3.35dB
-3.30dB
-3.25dB
-3.20dB
-3.15dB
-3.10dB
-3.05dB
-3.00dB
-2.95dB
-2.90dB
-2.85dB
-2.80dB

Value
768
769
770
771
772
773
774
775
776
777
778
779
780
781
782
783
784
785
786
787
788
789
790
791
792
793
794
795
796
797
798
799
800
801
802
803
804
805
806
807
808
809
810
811
812
813
814
815
816
817
818
819
820
821
822
823
824
825
826
827
828
829
830
831

Data
-2.75dB
-2.70dB
-2.65dB
-2.60dB
-2.55dB
-2.50dB
-2.45dB
-2.40dB
-2.35dB
-2.30dB
-2.25dB
-2.20dB
-2.15dB
-2.10dB
-2.05dB
-2.00dB
-1.95dB
-1.90dB
-1.85dB
-1.80dB
-1.75dB
-1.70dB
-1.65dB
-1.60dB
-1.55dB
-1.50dB
-1.45dB
-1.40dB
-1.35dB
-1.30dB
-1.25dB
-1.20dB
-1.15dB
-1.10dB
-1.05dB
-1.00dB
-0.95dB
-0.90dB
-0.85dB
-0.80dB
-0.75dB
-0.70dB
-0.65dB
-0.60dB
-0.55dB
-0.50dB
-0.45dB
-0.40dB
-0.35dB
-0.30dB
-0.25dB
-0.20dB
-0.15dB
-0.10dB
-0.05dB
0.00dB
0.05dB
0.10dB
0.15dB
0.20dB
0.25dB
0.30dB
0.35dB
0.40dB

Value
832
833
834
835
836
837
838
839
840
841
842
843
844
845
846
847
848
849
850
851
852
853
854
855
856
857
858
859
860
861
862
863
864
865
866
867
868
869
870
871
872
873
874
875
876
877
878
879
880
881
882
883
884
885
886
887
888
889
890
891
892
893
894
895

Data
0.45dB
0.50dB
0.55dB
0.60dB
0.65dB
0.70dB
0.75dB
0.80dB
0.85dB
0.90dB
0.95dB
1.00dB
1.05dB
1.10dB
1.15dB
1.20dB
1.25dB
1.30dB
1.35dB
1.40dB
1.45dB
1.50dB
1.55dB
1.60dB
1.65dB
1.70dB
1.75dB
1.80dB
1.85dB
1.90dB
1.95dB
2.00dB
2.05dB
2.10dB
2.15dB
2.20dB
2.25dB
2.30dB
2.35dB
2.40dB
2.45dB
2.50dB
2.55dB
2.60dB
2.65dB
2.70dB
2.75dB
2.80dB
2.85dB
2.90dB
2.95dB
3.00dB
3.05dB
3.10dB
3.15dB
3.20dB
3.25dB
3.30dB
3.35dB
3.40dB
3.45dB
3.50dB
3.55dB
3.60dB

Value
896
897
898
899
900
901
902
903
904
905
906
907
908
909
910
911
912
913
914
915
916
917
918
919
920
921
922
923
924
925
926
927
928
929
930
931
932
933
934
935
936
937
938
939
940
941
942
943
944
945
946
947
948
949
950
951
952
953
954
955
956
957
958
959

Data
3.65dB
3.70dB
3.75dB
3.80dB
3.85dB
3.90dB
3.95dB
4.00dB
4.05dB
4.10dB
4.15dB
4.20dB
4.25dB
4.30dB
4.35dB
4.40dB
4.45dB
4.50dB
4.55dB
4.60dB
4.65dB
4.70dB
4.75dB
4.80dB
4.85dB
4.90dB
4.95dB
5.00dB
5.05dB
5.10dB
5.15dB
5.20dB
5.25dB
5.30dB
5.35dB
5.40dB
5.45dB
5.50dB
5.55dB
5.60dB
5.65dB
5.70dB
5.75dB
5.80dB
5.85dB
5.90dB
5.95dB
6.00dB
6.05dB
6.10dB
6.15dB
6.20dB
6.25dB
6.30dB
6.35dB
6.40dB
6.45dB
6.50dB
6.55dB
6.60dB
6.65dB
6.70dB
6.75dB
6.80dB

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

Value
960
961
962
963
964
965
966
967
968
969
970
971
972
973
974
975
976
977
978
979
980
981
982
983
984
985
986
987
988
989
990
991
992
993
994
995
996
997
998
999
1000
1001
1002
1003
1004
1005
1006
1007
1008
1009
1010
1011
1012
1013
1014
1015
1016
1017
1018
1019
1020
1021
1022
1023

Data
6.85dB
6.90dB
6.95dB
7.00dB
7.05dB
7.10dB
7.15dB
7.20dB
7.25dB
7.30dB
7.35dB
7.40dB
7.45dB
7.50dB
7.55dB
7.60dB
7.65dB
7.70dB
7.75dB
7.80dB
7.85dB
7.90dB
7.95dB
8.00dB
8.05dB
8.10dB
8.15dB
8.20dB
8.25dB
8.30dB
8.35dB
8.40dB
8.45dB
8.50dB
8.55dB
8.60dB
8.65dB
8.70dB
8.75dB
8.80dB
8.85dB
8.90dB
8.95dB
9.00dB
9.05dB
9.10dB
9.15dB
9.20dB
9.25dB
9.30dB
9.35dB
9.40dB
9.45dB
9.50dB
9.55dB
9.60dB
9.65dB
9.70dB
9.75dB
9.80dB
9.85dB
9.90dB
9.95dB
10.00dB

62

6. Parameter Value Details

6.2. Other parameters (MTX3, MTX5-D)
6.2.1. INPUT PATCH
MTX3
Value
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30

MTX5-D
Displayed value
NONE
Input
1
2
3
4
5
6
7
8
ST IN
1L
1R
2L
2R
SD IN
L
R
YDIF
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16

Value
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30

Displayed value
NONE
Input
1
2
3
4
5
6
7
8
ST IN
1L
1R
2L
2R
SD IN
L
R
YDIF
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16

Value
Displayed value
31 Dante
1
32
2
33
3
34
4
35
5
36
6
37
7
38
8
39
9
40
10
41
11
42
12
43
13
44
14
45
15
46
16
47 SLOT
1
48
2
49
3
50
4
51
5
52
6
53
7
54
8
55
9
56
10
57
11
58
12
59
13
60
14
61
15
62
16

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

63

6. Parameter Value Details
6.2.2. INPUT CHANNEL
6.2.2.1. 3BAND EQ
Q

Type

Value Displayed value Value Displayed value Value Displayed value Value Displayed value
0
0.1
29
0.53
58
2.8
87
15.0
1
0.105
30
0.56
59
3.0
88
16.0
2
0.11
31
0.6
60
3.2
89
17.0
3
0.12
32
0.63
61
3.3
90
18.0
4
0.125
33
0.67
62
3.5
91
19.0
5
0.13
34
0.7
63
3.8
92
20.0
6
0.14
35
0.75
64
4.0
93
21.0
7
0.15
36
0.8
65
4.2
94
22.0
8
0.16
37
0.85
66
4.5
95
24.0
9
0.17
38
0.9
67
4.7
96
25.0
10
0.18
39
0.95
68
5.0
97
27.0
11
0.19
40
1.0
69
5.3
98
28.0
12
0.2
41
1.05
70
5.6
99
30.0
13
0.21
42
1.1
71
6.0 100
32.0
14
0.22
43
1.2
72
6.3 101
34.0
15
0.24
44
1.25
73
6.7 102
35.0
16
0.25
45
1.3
74
7.0 103
38.0
17
0.27
46
1.4
75
7.5 104
40.0
18
0.28
47
1.5
76
8 105
42.0
19
0.3
48
1.6
77
8.4 106
45.0
20
0.32
49
1.7
78
9.0 107
47.0
21
0.33
50
1.8
79
9.5 108
50.0
22
0.35
51
1.9
80
10.0 109
53.0
23
0.38
52
2.0
81
10.5 110
56.0
24
0.4
53
2.1
82
11.0 111
60.0
25
0.42
54
2.2
83
12.0 112
63.0
26
0.45
55
2.4
84
12.5
27
0.47
56
2.5
85
13.0
28
0.5
57
2.7
86
14.0

Value
0
1
2
3
4
5
6

Displayed value
PEQ
L.SHELF 6dB/Oct
L.SHELF 12dB/Oct
H.SHELF 6dB/Oct
H.SHELF 12dB/Oct
HPF
LPF

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

64

6. Parameter Value Details
6.2.2.2. GATE
Decay
Value Displayed value Value Displayed value Value Displayed value Value Displayed value
0
3msec
43
189msec
86
1.23sec 129
7.68sec
1
7msec
44
196msec
87
1.28sec 130
8.11sec
2
10msec
45
203msec
88
1.34sec 131
8.54sec
3
13msec
46
209msec
89
1.39sec 132
8.97sec
4
17msec
47
219msec
90
1.44sec 133
9.39sec
5
22msec
48
229msec
91
1.50sec 134
9.82sec
6
25msec
49
243msec
92
1.55sec 135
10.2sec
7
28msec
50
256msec
93
1.60sec 136
10.7sec
8
32msec
51
269msec
94
1.66sec 137
11.1sec
9
35msec
52
283msec
95
1.74sec 138
11.5sec
10
38msec
53
296msec
96
1.82sec 139
12.0sec
11
42msec
54
309msec
97
1.92sec 140
12.4sec
12
45msec
55
323msec
98
2.03sec 141
12.8sec
13
48msec
56
336msec
99
2.14sec 142
13.2sec
14
52msec
57
349msec 100
2.24sec 143
13.9sec
15
55msec
58
363msec 101
2.35sec 144
14.5sec
16
59msec
59
376msec 102
2.46sec 145
15.4sec
17
63msec
60
390msec 103
2.56sec 146
16.2sec
18
66msec
61
403msec 104
2.67sec 147
17.1sec
19
69msec
62
416msec 105
2.78sec 148
17.9sec
20
73msec
63
436msec 106
2.89sec 149
18.8sec
21
76msec
64
456msec 107
2.99sec 150
19.6sec
22
79msec
65
483msec 108
3.10sec 151
20.5sec
23
83msec
66
509msec 109
3.21sec 152
21.4sec
24
86msec
67
536msec 110
3.31sec 153
22.2sec
25
89msec
68
563msec 111
3.47sec 154
23.1sec
26
93msec
69
589msec 112
3.63sec 155
23.9sec
27
96msec
70
616msec 113
3.84sec 156
24.8sec
28
99msec
71
643msec 114
4.06sec 157
25.6sec
29
103msec
72
670msec 115
4.27sec 158
26.5sec
30
106msec
73
696msec 116
4.48sec 159
27.7sec
31
111msec
74
723msec 117
4.70sec 160
29.0sec
32
116msec
75
750msec 118
4.91sec 161
30.7sec
33
123msec
76
777msec 119
5.13sec 162
32.4sec
34
129msec
77
803msec 120
5.34sec 163
34.1sec
35
136msec
78
830msec 121
5.55sec 164
35.9sec
36
143msec
79
870msec 122
5.77sec 165
37.6sec
37
149msec
80
909msec 123
5.98sec 166
39.3sec
38
156msec
81
963msec 124
6.20sec 167
41.0sec
39
163msec
82
1.02sec 125
6.41sec 168
42.7sec
40
169msec
83
1.07sec 126
6.62sec
41
176msec
84
1.12sec 127
6.94sec
42
183msec
85
1.18sec 128
7.26sec

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

65

6. Parameter Value Details
Hold
Value Displayed value Value Displayed value Value Displayed value Value Displayed value
0
0.02msec
54
2.01msec 108
20.2msec 162
211msec
1
0.04msec
55
2.10msec 109
20.9msec 163
222msec
2
0.07msec
56
2.19msec 110
21.6msec 164
233msec
3
0.09msec
57
2.28msec 111
22.6msec 165
245msec
4
0.11msec
58
2.36msec 112
23.6msec 166
256msec
5
0.14msec
59
2.45msec 113
25.0msec 167
267msec
6
0.16msec
60
2.54msec 114
26.4msec 168
278msec
7
0.18msec
61
2.62msec 115
27.8msec 169
289msec
8
0.21msec
62
2.71msec 116
29.2msec 170
300msec
9
0.23msec
63
2.84msec 117
30.6msec 171
311msec
10
0.25msec
64
2.97msec 118
32.0msec 172
323msec
11
0.27msec
65
3.14msec 119
33.4msec 173
334msec
12
0.29msec
66
3.32msec 120
34.8msec 174
345msec
13
0.31msec
67
3.49msec 121
36.2msec 175
361msec
17
0.41msec
71
4.19msec 125
41.7msec 179
445msec
18
0.43msec
72
4.36msec 126
43.1msec 180
467msec
19
0.45msec
73
4.53msec 127
45.2msec 181
489msec
20
0.47msec
74
4.71msec 128
47.2msec 182
511msec
21
0.49msec
75
4.88msec 129
50.0msec 183
534msec
22
0.52msec
76
5.06msec 130
52.8msec 184
556msec
23
0.54msec
77
5.23msec 131
55.6msec 185
578msec
24
0.56msec
78
5.40msec 132
58.4msec 186
601msec
25
0.58msec
79
5.66msec 133
61.2msec 187
623msec
26
0.60msec
80
5.92msec 134
63.9msec 188
645msec
27
0.62msec
81
6.27msec 135
66.7msec 189
667msec
28
0.65msec
82
6.61msec 136
69.5msec 190
690msec
29
0.67msec
83
6.96msec 137
72.3msec 191
723msec
30
0.69msec
84
7.31msec 138
75.1msec 192
756msec
31
0.72msec
85
7.66msec 139
77.9msec 193
800msec
32
0.75msec
86
8.01msec 140
80.7msec 194
845msec
33
0.80msec
87
8.36msec 141
83.4msec 195
889msec
34
0.84msec
88
8.70msec 142
86.2msec 196
934msec
35
0.88msec
89
9.05msec 143
90.3msec 197
978msec
36
0.93msec
90
9.40msec 144
94.5msec 198
1.02sec
37
0.97msec
91
9.75msec 145
100msec 199
1.07sec
38
1.02msec
92
10.1msec 146
106msec 200
1.11sec
39
1.06msec
93
10.4msec 147
111msec 201
1.16sec
40
1.10msec
94
10.8msec 148
117msec 202
1.20sec
41
1.15msec
95
11.3msec 149
122msec 203
1.25sec
42
1.19msec
96
11.8msec 150
128msec 204
1.29sec
43
1.23msec
97
12.5msec 151
133msec 205
1.33sec
44
1.28msec
98
13.2msec 152
139msec 206
1.38sec
45
1.32msec
99
13.9msec 153
145msec 207
1.45sec
46
1.36msec 100
14.6msec 154
150msec 208
1.51sec
47
1.43msec 101
15.3msec 155
156msec 209
1.60sec
48
1.49msec 102
16.0msec 156
161msec 210
1.69sec
49
1.58msec 103
16.7msec 157
167msec 211
1.78sec
50
1.67msec 104
17.4msec 158
172msec 212
1.87sec
51
1.75msec 105
18.1msec 159
181msec 213
1.96sec
52
1.84msec 106
18.8msec 160
189msec
53
1.93msec 107
19.5msec 161
200msec

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

66

6. Parameter Value Details
6.2.2.3. COMPRESSOR
Ratio

Knee

Value Displayed value Value Displayed value Value Displayed value Value Displayed value
10
1.0:1
58
5.8:1 106
10.6:1 154
15.4:1
11
1.1:1
59
5.9:1 107
10.7:1 155
15.5:1
12
1.2:1
60
6.0:1 108
10.8:1 156
15.6:1
13
1.3:1
61
6.1:1 109
10.9:1 157
15.7:1
14
1.4:1
62
6.2:1 110
11.0:1 158
15.8:1
15
1.5:1
63
6.3:1 111
11.1:1 159
15.9:1
16
1.6:1
64
6.4:1 112
11.2:1 160
16.0:1
17
1.7:1
65
6.5:1 113
11.3:1 161
16.1:1
18
1.8:1
66
6.6:1 114
11.4:1 162
16.2:1
19
1.9:1
67
6.7:1 115
11.5:1 163
16.3:1
20
2.0:1
68
6.8:1 116
11.6:1 164
16.4:1
21
2.1:1
69
6.9:1 117
11.7:1 165
16.5:1
22
2.2:1
70
7.0:1 118
11.8:1 166
16.6:1
23
2.3:1
71
7.1:1 119
11.9:1 167
16.7:1
24
2.4:1
72
7.2:1 120
12.0:1 168
16.8:1
25
2.5:1
73
7.3:1 121
12.1:1 169
16.9:1
26
2.6:1
74
7.4:1 122
12.2:1 170
17.0:1
27
2.7:1
75
7.5:1 123
12.3:1 171
17.1:1
28
2.8:1
76
7.6:1 124
12.4:1 172
17.2:1
29
2.9:1
77
7.7:1 125
12.5:1 173
17.3:1
30
3.0:1
78
7.8:1 126
12.6:1 174
17.4:1
31
3.1:1
79
7.9:1 127
12.7:1 175
17.5:1
32
3.2:1
80
8.0:1 128
12.8:1 176
17.6:1
33
3.3:1
81
8.1:1 129
12.9:1 177
17.7:1
34
3.4:1
82
8.2:1 130
13.0:1 178
17.8:1
35
3.5:1
83
8.3:1 131
13.1:1 179
17.9:1
36
3.6:1
84
8.4:1 132
13.2:1 180
18.0:1
37
3.7:1
85
8.5:1 133
13.3:1 181
18.1:1
38
3.8:1
86
8.6:1 134
13.4:1 182
18.2:1
39
3.9:1
87
8.7:1 135
13.5:1 183
18.3:1
40
4.0:1
88
8.8:1 136
13.6:1 184
18.4:1
41
4.1:1
89
8.9:1 137
13.7:1 185
18.5:1
42
4.2:1
90
9.0:1 138
13.8:1 186
18.6:1
43
4.3:1
91
9.1:1 139
13.9:1 187
18.7:1
44
4.4:1
92
9.2:1 140
14.0:1 188
18.8:1
45
4.5:1
93
9.3:1 141
14.1:1 189
18.9:1
46
4.6:1
94
9.4:1 142
14.2:1 190
19.0:1
47
4.7:1
95
9.5:1 143
14.3:1 191
19.1:1
48
4.8:1
96
9.6:1 144
14.4:1 192
19.2:1
49
4.9:1
97
9.7:1 145
14.5:1 193
19.3:1
50
5.0:1
98
9.8:1 146
14.6:1 194
19.4:1
51
5.1:1
99
9.9:1 147
14.7:1 195
19.5:1
52
5.2:1 100
10.0:1 148
14.8:1 196
19.6:1
53
5.3:1 101
10.1:1 149
14.9:1 197
19.7:1
54
5.4:1 102
10.2:1 150
15.0:1 198
19.8:1
55
5.5:1 103
10.3:1 151
15.1:1 199
19.9:1
56
5.6:1 104
10.4:1 152
15.2:1 200
20.0:1
57
5.7:1 105
10.5:1 153
15.3:1 201
∞:1

Value Displayed value
0
HARD
1
1
2
2
3
3
4
4
5
5
Release
Same as 6.2.2.2. Gate
/ Decay

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

67

6. Parameter Value Details
6.2.2.4. AGC
Response Time
Value Displayed value Value Displayed value
0
100msec
30
2.20sec
1
150msec
31
2.30sec
2
200msec
32
2.40sec
3
250msec
33
2.50sec
4
300msec
34
2.60sec
5
350msec
35
2.70sec
6
400msec
36
2.80sec
7
450msec
37
2.90sec
8
500msec
38
3.00sec
9
550msec
39
3.10sec
10
600msec
40
3.20sec
12
700msec
42
3.40sec
13
750msec
43
3.50sec
14
800msec
44
3.60sec
15
850msec
45
3.70sec
16
900msec
46
3.80sec
17
950msec
47
3.90sec
18
1.00sec
48
4.00sec
19
1.10sec
49
4.10sec
20
1.20sec
50
4.20sec
21
1.30sec
51
4.30sec
22
1.40sec
52
4.40sec
23
1.50sec
53
4.50sec
24
1.60sec
54
4.60sec
25
1.70sec
55
4.70sec
26
1.80sec
56
4.80sec
27
1.90sec
57
4.90sec
28
2.00sec
58
5.00sec
29
2.10sec

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

68

6. Parameter Value Details
6.2.2.5. DUGAN AUTOMIXER
Mode
Value Displayed value
0
Mute
1
Man
2
Auto
Weight
Value Displayed value
-3000
-100.0
-2950
-29.5
-2900
-29.0
-2850
-28.5
:
:
:
:
-100
-1.0
-50
-0.5
0
0.0
50
0.5
100
1.0
:
:
:
:
1350
13.5
1400
14.0
1450
14.5
1500
15.0
Group
MTX3

MTX5-D

Value Displayed value
0
a
1
b

Value Displayed value
0
a
1
b
2
c
3
d

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

69

6. Parameter Value Details
6.2.3. EFFECT
Type
Value
0
1
2
3

Displayed value
Reverb Hall
Reverb Stage1
Karaoke Echo
Vocal Echo

RevHallTime/RevStageTime
Value
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28

Time(sec)

Time (msec) Value
135.5
86
138.6
87
141.8
88
144.9
89
148.1
90
151.2
91
154.4
92
157.5
93
160.7
94
163.8
95
167.0
96
170.1
97
173.3
98
176.4
99
179.6 100
182.7 101
185.9 102
189.0 103
192.2 104
195.3 105
198.5 106
201.6 107
204.8 108
207.9 109
211.1 110
214.2 111
217.4 112
220.5 113
223.7 114
226.8 115
230.0 116
233.1 117
236.3 118
239.4 119
242.6 120
245.7 121
248.9 122
252.0 123
255.2 124
258.3 125
261.5 126
264.6 127
267.7

Time (msec)
270.9
274.0
277.2
280.3
283.5
286.6
289.8
292.9
296.1
299.2
302.4
305.5
308.7
311.8
315.0
318.1
321.3
324.4
327.6
330.7
333.9
337.0
340.2
343.3
346.5
349.6
352.8
355.9
359.1
362.2
365.4
368.5
371.7
374.8
378.0
381.1
384.3
387.4
390.6
393.7
396.9
400.0

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

70

0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
2.0
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
3.0
3.1

Value
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57

KaraokeTime/VocalTime
Time(sec)
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
4.0
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
5.0
5.5
6.0
6.5
7.0
7.5
8.0
8.5
9.0
9.5
10.0

Value
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42

Time (msec) Value
0.4
43
3.2
44
6.4
45
9.5
46
12.7
47
15.8
48
19.0
49
22.1
50
25.3
51
28.4
52
31.6
53
34.7
54
37.9
55
41.0
56
44.2
57
47.3
58
50.5
59
53.6
60
56.8
61
59.9
62
63.1
63
66.2
64
69.4
65
72.5
66
75.7
67
78.8
68
82.0
69
85.1
70
88.3
71
91.4
72
94.6
73
97.7
74
100.9
75
104.0
76
107.2
77
110.3
78
113.5
79
116.6
80
119.8
81
122.9
82
126.1
83
129.2
84
132.4
85

6. Parameter Value Details
6.2.4. ZONE
6.2.4.1. PAGING (MTX5-D only)
Paging Source
MTX5-D
Value Displayed value Value Displayed value
0
NONE
31
YDIF IN 1
1
CH1
32
YDIF IN 2
2
CH2
33
YDIF IN 3
3
CH3
34
YDIF IN 4
4
CH4
35
YDIF IN 5
5
CH5
36
YDIF IN 6
6
CH6
37
YDIF IN 7
7
CH7
38
YDIF IN 8
8
CH8
39
YDIF IN 9
9
CH9
40
YDIF IN 10
10
CH10
41
YDIF IN 11
11
CH11
42
YDIF IN 12
12
CH12
43
YDIF IN 13
13
CH13
44
YDIF IN 14
14
CH14
45
YDIF IN 15
15
CH15
46
YDIF IN 16
16
CH16
47
ANC BUS1
17
STIN1L
48
ANC BUS2
18
STIN1R
19
STIN2L
20
STIN2R
21
STIN3L
22
STIN3R
23
CH17
24
CH18
25
CH19
26
CH20
27
CH21
28
CH22
29
CH23
30
CH24
Range
MTX5-D
Value Displayed value
-601
-∞
-600
-60.0dB
-599
-59.9dB
:
:
:
:
-2
-0.2dB
-1
-0.1dB
0
-0.0dB

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

71

6. Parameter Value Details
6.2.4.2. 1st/2nd PRIORITY
1st/2nd Priority Ducker Priority Source
MTX3
MTX5-D
Value Displayed value
0
NONE
1
CH1
2
CH2
3
CH3
4
CH4
5
CH5
6
CH6
7
CH7
8
CH8
9
STIN1L
10
STIN1R
11
STIN2L
12
STIN2R
13
STIN3L
14
STIN3R
15
CH9
16
CH10
17
CH11
18
CH12
19
CH13
20
CH14
21
CH15
22
CH16
23
YDIF IN 1
24
YDIF IN 2
25
YDIF IN 3
26
YDIF IN 4
27
YDIF IN 5
28
YDIF IN 6
29
YDIF IN 7
30
YDIF IN 8
31
YDIF IN 9
32
YDIF IN 10
33
YDIF IN 11
34
YDIF IN 12
35
YDIF IN 13
36
YDIF IN 14
37
YDIF IN 15
38
YDIF IN 16
39
ANC BUS1
40
ANC BUS2

Value Displayed value Value Displayed value
0
NONE
31
YDIF IN 1
1
CH1
32
YDIF IN 2
2
CH2
33
YDIF IN 3
3
CH3
34
YDIF IN 4
4
CH4
35
YDIF IN 5
5
CH5
36
YDIF IN 6
6
CH6
37
YDIF IN 7
7
CH7
38
YDIF IN 8
8
CH8
39
YDIF IN 9
9
CH9
40
YDIF IN 10
10
CH10
41
YDIF IN 11
11
CH11
42
YDIF IN 12
12
CH12
43
YDIF IN 13
13
CH13
44
YDIF IN 14
14
CH14
45
YDIF IN 15
15
CH15
46
YDIF IN 16
16
CH16
47
ANC BUS1
17
STIN1L
48
ANC BUS2
18
STIN1R
19
STIN2L
20
STIN2R
21
STIN3L
22
STIN3R
23
CH17
24
CH18
25
CH19
26
CH20
27
CH21
28
CH22
29
CH23
30
CH24

Release
Same as 6.2.2.2. Gate / Decay
Hold
Same as 6.2.2.2. Gate / Hold

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

72

6. Parameter Value Details
6.2.4.3. ANC
ANC Source
Same as 6.2.4.2. 1st/2nd PRIORITY / 1st/2nd Priority Ducker Priority Source
ANC Ratio
Value Displayed value
5
0.5:1
6
0.6:1
7
0.7:1
8
0.8:1
9
0.9:1
10
1.0:1
11
1.1:1
12
1.2:1
13
1.3:1
14
1.4:1
15
1.5:1
16
1.6:1
17
1.7:1
18
1.8:1
19
1.9:1
20
2.0:1

6.2.5. ROUTER
6.2.5.1. ROUTER
MTX3

MTX5-D

Value Displayed value
0
NONE
1
ZONE 1
2
ZONE 2
3
ZONE 3
4
ZONE 4
5
ZONE 5
6
ZONE 6
7
ZONE 7
8
ZONE 8
9
YDIF IN 1
10
YDIF IN 2
11
YDIF IN 3
12
YDIF IN 4
13
YDIF IN 5
14
YDIF IN 6
15
YDIF IN 7
16
YDIF IN 8
17
YDIF IN 9
18
YDIF IN 10
19
YDIF IN 11
20
YDIF IN 12
21
YDIF IN 13
22
YDIF IN 14
23
YDIF IN 15
24
YDIF IN 16

Value Displayed value Value Displayed value
0
NONE
17
YDIF IN 1
1
ZONE 1
18
YDIF IN 2
2
ZONE 2
19
YDIF IN 3
3
ZONE 3
20
YDIF IN 4
4
ZONE 4
21
YDIF IN 5
5
ZONE 5
22
YDIF IN 6
6
ZONE 6
23
YDIF IN 7
7
ZONE 7
24
YDIF IN 8
8
ZONE 8
25
YDIF IN 9
9
ZONE 9
26
YDIF IN 10
10
ZONE 10
27
YDIF IN 11
11
ZONE 11
28
YDIF IN 12
12
ZONE 12
29
YDIF IN 13
13
ZONE 13
30
YDIF IN 14
14
ZONE 14
31
YDIF IN 15
15
ZONE 15
32
YDIF IN 16
16
ZONE 16

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

73

6. Parameter Value Details
6.2.5.2. OSCILLATOR
Waveform
Value Displayed value
0
SINE 100Hz
1
SINE 1kHz
2
SINE 10kHz
3
Pink
4
Burst
5
VARI

6.2.6. OUTPUT CHANNEL
6.2.6.1. 4BAND EQ
Q
Same as 6.2.2.1. 3BAND EQ / Q
Type
Same as 6.2.2.1. 3BAND EQ / Type
B/W(Q)
Value
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28

Oct.
6.672
6.534
6.403
6.158
6.044
5.934
5.728
5.537
5.359
5.193
5.037
4.891
4.753
4.623
4.499
4.271
4.165
3.968
3.876
3.704
3.546
3.472
3.331
3.139
3.023
2.914
2.764
2.671
2.543

Value
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57

Oct.
2.426
2.319
2.189
2.100
1.991
1.917
1.804
1.703
1.612
1.530
1.456
1.388
1.327
1.270
1.170
1.125
1.084
1.010
0.945
0.888
0.837
0.792
0.751
0.714
0.681
0.650
0.597
0.573
0.531

Value
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86

Oct.
0.513
0.479
0.449
0.436
0.411
0.379
0.360
0.343
0.320
0.306
0.288
0.272
0.257
0.240
0.229
0.215
0.206
0.192
0.180
0.172
0.160
0.152
0.144
0.137
0.131
0.120
0.115
0.111
0.103

Value
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112

Oct.
0.096
0.090
0.085
0.080
0.076
0.072
0.069
0.066
0.060
0.058
0.053
0.052
0.048
0.045
0.042
0.041
0.038
0.036
0.034
0.032
0.031
0.029
0.027
0.026
0.024
0.023

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

74

6. Parameter Value Details
6.2.6.2. SPEAKER PROCESSOR
HPF/LPF Type

PEQ Type

Value
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19

Value
0
1
2
3
4
5
6
7
8
9

Displayed value
Thru
6dB/Oct
12dB/Oct AdjustGc
12dB/Oct Butrwrth
12dB/Oct Bessel
12dB/Oct Linkwitz
18dB/Oct AdjustGc
18dB/Oct Butrwrth
18dB/Oct Bessel
24dB/Oct AdjustGc
24dB/Oct Butrwrth
24dB/Oct Bessel
24dB/Oct Linkwitz
32dB/Oct AdjustGc
32dB/Oct Butrwrth
32dB/Oct Bessel
48dB/Oct AdjustGc
48dB/Oct Butrwrth
48dB/Oct Bessel
48dB/Oct Linkwitz

Limiter Release
Same as 6.2.2.2. GATE / Decay

Displayed value
PEQ
L.SHELF 6dB/Oct
L.SHELF 12dB/Oct
H.SHELF 6dB/Oct
H.SHELF 12dB/Oct
HPF
LPF
APF 1st
APF 2nd
Horn EQ

PEQ Q
Same as 6.2.2.1. 3BAND EQ / Q
B/W(Q)
Same as 6.2.6.1. 4BAND EQ / B/W(Q)

Limiter Attack/Release Mode
Value
0
1
2
3

Displayed value
Fast
Mid
Slow
Manual

6.2.7. OUTPUT PATCH
6.2.7.1. OUTPUT PATCH
MTX3

MTX5-D

Value Displayed value
0
NONE
1 OUTPUT CH1
2 OUTPUT CH2
3 OUTPUT CH3
4 OUTPUT CH4
5 OUTPUT CH5
6 OUTPUT CH6
7 OUTPUT CH7
8 OUTPUT CH8

Value
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16

Displayed value
NONE
OUTPUT CH1
OUTPUT CH2
OUTPUT CH3
OUTPUT CH4
OUTPUT CH5
OUTPUT CH6
OUTPUT CH7
OUTPUT CH8
OUTPUT CH9
OUTPUT CH10
OUTPUT CH11
OUTPUT CH12
OUTPUT CH13
OUTPUT CH14
OUTPUT CH15
OUTPUT CH16

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

75

6. Parameter Value Details
6.2.7.2. YDIF PATCH
MTX3

MTX5-D

Value Displayed value
0
NONE
1
CH1
2
CH2
3
CH3
4
CH4
5
CH5
6
CH6
7
CH7
8
CH8
9
STIN1L
10
STIN1R
11
STIN2L
12
STIN2R
13
STIN3L
14
STIN3R
15
ZONE 1
16
ZONE 2
17
ZONE 3
18
ZONE 4
19
ZONE 5
20
ZONE 6
21
ZONE 7
22
ZONE 8
23
THRU 1
24
THRU 2
25
THRU 3
26
THRU 4
27
THRU 5
28
THRU 6
29
THRU 7
30
THRU 8
31
THRU 9
32
THRU 10
33
THRU 11
34
THRU 12
35
THRU 13
36
THRU 14
37
THRU 15
38
THRU 16
39 OUTPUT CH1
40 OUTPUT CH2
41 OUTPUT CH3
42 OUTPUT CH4
43 OUTPUT CH5
44 OUTPUT CH6
45 OUTPUT CH7
46 OUTPUT CH8

Value Displayed value Value Displayed value
0
NONE
39
THRU 1
1
CH1
40
THRU 2
2
CH2
41
THRU 3
3
CH3
42
THRU 4
4
CH4
43
THRU 5
5
CH5
44
THRU 6
6
CH6
45
THRU 7
7
CH7
46
THRU 8
8
CH8
47
THRU 9
9
CH9
48
THRU 10
10
CH10
49
THRU 11
11
CH11
50
THRU 12
12
CH12
51
THRU 13
13
CH13
52
THRU 14
14
CH14
53
THRU 15
15
CH15
54
THRU 16
16
CH16
55 OUTPUT CH1
17
STIN1L
56 OUTPUT CH2
18
STIN1R
57 OUTPUT CH3
19
STIN2L
58 OUTPUT CH4
20
STIN2R
59 OUTPUT CH5
21
STIN3L
60 OUTPUT CH6
22
STIN3R
61 OUTPUT CH7
23
ZONE 1
62 OUTPUT CH8
24
ZONE 2
63 OUTPUT CH9
25
ZONE 3
64 OUTPUT CH10
26
ZONE 4
65 OUTPUT CH11
27
ZONE 5
66 OUTPUT CH12
28
ZONE 6
67 OUTPUT CH13
29
ZONE 7
68 OUTPUT CH14
30
ZONE 8
69 OUTPUT CH15
31
ZONE 9
70 OUTPUT CH16
32
ZONE 10
33
ZONE 11
34
ZONE 12
35
ZONE 13
36
ZONE 14
37
ZONE 15
38
ZONE 16

* About MTX3 23 to 38 (THRU1 to 16), MTX5-D 39 to 54 (THRU1 to 16)
Note the difference in behavior between the MTX Editor and MTX external control protocol. On the MTX editor, when you
press THRU, one of the 16 YDIF channels is selected automatically.
However, with the MTX external control protocol, you can select the channel freely.

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

76

6. Parameter Value Details
6.2.8. MY4-AEC
6.2.8.1. MY4-AEC Input Patch
Near-end Mic / From Far-end
Value
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46

PORT
NONE
Input

ST IN

SD IN
YDIF

DANTE

1
2
3
4
5
6
7
8
1L
1R
2L
2R
L
R
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16

Value
47 SLOT
48
49
50
51 Output
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66

PORT
1
2
3
4
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16

6.2.8.2. MY4-AEC FBS
Width

Depth

Value Displayed value
0
1/10oct
1
1/60oct
2
1/93oct

Value Displayed value
0
-6dB
1
-12dB
2
-18dB

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

77

6. Parameter Value Details

6.3. Other parameters (MRX7-D)
6.3.1. Ambient Noise Compensator
Ratio
Same as 6.2.4.3. ANC ANC Ratio in "Other Parameters (MTX3,MTX5-D)"

6.3.2. Auto Gain Control
Response Type
Same as 6.2.2.4. AGC Response Time in "Other Parameters (MTX3,MTX5-D)"

6.3.3. Combiner
6.3.3.1. Room Combiner
Source
Value Displayed value
0
BGM1
1
BGM2
2
BGM3
3
BGM4

6.3.3.2. Room Combiner plus Automixer
Source
Same as 6.3.3.1. Room Combiner Source in "Other Parameters (MTX3,MTX5-D)"
Mode
Same as 6.2.2.5. DUGAN AUTOMIXER Mode in "Other Parameters (MTX3,MTX5-D)"
Weight
Same as 6.2.2.5. DUGAN AUTOMIXER Weight in "Other Parameters (MTX3,MTX5-D)"

6.3.4. Dynamics
6.3.4.1. Compressor
Ratio
Same as 6.2.2.3. COMPRESSOR Ratio in "Other Parameters (MTX3,MTX5-D)"
Knee
Same as 6.2.2.3. COMPRESSOR Knee in "Other Parameters (MTX3,MTX5-D)"
Release
Same as 6.2.2.3. GATE Decay in "Other Parameters (MTX3,MTX5-D)"
Keyin(Mono)

Keyin(Stereo)

Value Displayed value
0
SELF
1
KEYIN

Value Displayed value
2
L
3
R
4
LR BOTH
5
KEYIN

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

78

6. Parameter Value Details
6.3.4.2. Gate/Ducking
Release
Same as 6.2.2.3. GATE Decay in "Other Parameters (MTX3,MTX5-D)"
Decay
Same as 6.2.2.3. GATE Decay in "Other Parameters (MTX3,MTX5-D)"
Hold
Same as 6.2.2.3. GATE Hold in "Other Parameters (MTX3,MTX5-D)"
Keyin(Mono)
Same as 6.3.4.1. Compressor Keyin(Mono)
Keyin(Stereo)
Same as 6.3.4.1. Compressor Keyin(Stereo)
6.3.4.3. Limiter
Release
Same as 6.2.2.3. GATE Decay in "Other Parameters (MTX3,MTX5-D)"
Keyin(Mono)
Same as 6.3.4.1. Compressor Keyin(Mono)
Keyin(Stereo)
Same as 6.3.4.1. Compressor Keyin(Stereo)
6.3.4.4. Paging Ducker
Range
Same as 6.2.4.1. PAGING Range in "Other Parameters (MTX3,MTX5-D)"

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

79

6. Parameter Value Details
6.3.5. Effect
Type
Same as 6.2.3. EFFECT Type in "Other Parameters (MTX3,MTX5-D)"
RevHallTime/RevStageTime
Same as 6.2.3. EFFECT RevHallTime/RevStageTime in "Other Parameters (MTX3,MTX5-D)"
KaraokeTime/VocalTime
Value
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51

Time(msec) Value
0.4
52
3.2
53
6.4
54
9.5
55
12.7
56
15.8
57
19.0
58
22.1
59
25.3
60
28.4
61
31.6
62
34.7
63
37.9
64
41.0
65
44.2
66
47.3
67
50.5
68
53.6
69
56.8
70
59.9
71
63.1
72
66.2
73
69.4
74
72.5
75
75.7
76
78.8
77
82.0
78
85.1
79
88.3
80
91.4
81
94.6
82
97.7
83
100.9
84
104.0
85
107.2
86
110.3
87
113.5
88
116.6
89
119.8
90
122.9
91
126.1
92
129.2
93
132.4
94
135.5
95
138.6
96
141.8
97
144.9
98
148.1
99
151.2 100
154.4 101
157.5 102
160.7 103

Time(msec) Value
163.8 104
167.0 105
170.1 106
173.3 107
176.4 108
179.6 109
182.7 110
185.9 111
189.0 112
192.2 113
195.3 114
198.5 115
201.6 116
204.8 117
207.9 118
211.1 119
214.2 120
217.4 121
220.5 122
223.7 123
226.8 124
230.0 125
233.1 126
236.3 127
239.4 128
242.6 129
245.7 130
248.9 131
252.0 132
255.2 133
258.3 134
261.5 135
264.6 136
267.7 137
270.9 138
274.0 139
277.2 140
280.3 141
283.5 142
286.6 143
289.8 144
292.9 145
296.1 146
299.2 147
302.4 148
305.5 149
308.7 150
311.8 151
315.0 152
318.1 153
321.3 154
324.4 155

Time(msec) Value
327.6 156
330.7 157
333.9 158
337.0 159
340.2 160
343.3 161
346.5 162
349.6 163
352.8 164
355.9 165
359.1 166
362.2 167
365.4 168
368.5 169
371.7 170
374.8 171
378.0 172
381.1 173
384.3 174
387.4 175
390.6 176
393.7 177
396.9 178
400.0 179
404.7 180
409.4 181
414.1 182
418.8 183
423.4 184
428.1 185
432.8 186
437.5 187
442.2 188
446.9 189
451.6 190
456.3 191
460.9 192
465.6 193
470.3 194
475.0 195
479.7 196
484.4 197
489.1 198
493.8 199
498.4 200
503.1 201
507.8 202
512.5 203
517.2 204
521.9 205
526.6 206
531.3 207

Time(msec) Value
535.9 208
540.6 209
545.3 210
550.0 211
554.7 212
559.4 213
564.1 214
568.8 215
573.4 216
578.1 217
582.8 218
587.5 219
592.2 220
596.9 221
601.6 222
606.3 223
610.9 224
615.6 225
620.3 226
625.0 227
629.7 228
634.4 229
639.1 230
643.8 231
648.4 232
653.1 233
657.8 234
662.5 235
667.2 236
671.9 237
676.6 238
681.3 239
685.9 240
690.6 241
695.3 242
700.0 243
704.7 244
709.4 245
714.1 246
718.8 247
723.4 248
728.1 249
732.8 250
737.5 251
742.2 252
746.9 253
751.6 254
756.3 255
760.9
765.6
770.3
775.0

Time(msec)
779.7
784.4
789.1
793.8
798.4
803.1
807.8
812.5
817.2
821.9
826.6
831.3
835.9
840.6
845.3
850.0
854.7
859.4
864.1
868.8
873.4
878.1
882.8
887.5
892.2
896.9
901.6
906.3
910.9
915.6
920.3
925.0
929.7
934.4
939.1
943.8
948.4
953.1
957.8
962.5
967.2
971.9
976.6
981.3
985.9
990.6
995.3
1000.0

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

80

6. Parameter Value Details
6.3.6. EQ
6.3.6.1. GEQ
Q
Same as 6.2.2.1. 3BAND EQ Q in "Other Parameters (MTX3,MTX5-D)"
6.3.6.2. PEQ
Q
Same as 6.2.2.1. 3BAND EQ Q in "Other Parameters (MTX3,MTX5-D)"
B/W(Q)
Same as 6.2.6.1. 4BAND EQ B/W(Q) in "Other Parameters (MTX3,MTX5-D)"
Type
Same as 6.2.2.1. 3BAND EQ Type in "Other Parameters (MTX3,MTX5-D)"

6.3.7. Filter
6.3.7.1. HPF/LPF/BPF
Filter Type
Same as 6.2.6.2. SPEAKER PROCESSOR HPF/LPF Type in "Other Parameters (MTX3,MTX5-D)"

6.3.8. Mixer
6.3.8.1. Dugan Automixer
Mode
Same as 6.2.2.5. DUGAN AUTOMIXER Mode in "Other Parameters (MTX3,MTX5-D)"
Weight
Same as 6.2.2.5. DUGAN AUTOMIXER Weight in "Other Parameters (MTX3,MTX5-D)"
Group(2 - 4 Channel)
Value Displayed value
0
a
1
b
Group(5 - 8 Channel)
Value Displayed value
0
a
1
b
2
c
3
d
Group(9 - 24 Channnel)
Value Displayed value
0
a
1
b
2
c
3
d
4
e
5
f
6
g
7
h

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

81

6. Parameter Value Details
6.3.9. Oscillator
Waveform
Same as 6.2.5.2. OSCILLATOR Waveform in "Other Parameters (MTX3,MTX5-D)"

6.3.10. Paging
Range
Same as 6.2.4.1. PAGING Range in "Other Parameters (MTX3,MTX5-D)"

6.3.11. Speech Privacy
Select Type
Value Displayed value
0
Forest
1
Seashore
2
Street
3
Building

6.3.12. Speaker Processor
HPF/LPF Type
Same as 6.2.6.2. SPEAKER PROCESSOR HPF/LPF Type in "Other Parameters (MTX3,MTX5-D)"
PEQ Q
Same as 6.2.2.1. 3BAND EQ Q in "Other Parameters (MTX3,MTX5-D)"
PEQ B/WQ
Same as 6.2.6.1. 4BAND EQ B/W(Q) in "Other Parameters (MRX7-D)"
PEQ Type
Same as 6.2.6.2. SPEAKER PROCESSOR PEQ Type in "Other Parameters (MTX3,MTX5-D)"
Limiter Release
Same as 6.2.2.2. GATE Decay in "Other Parameters (MTX3,MTX5-D)"
Limiter Attack/Release Mode
Same as 6.2.6.2. SPEAKER PROCESSOR Limiter Attack/Release Mode in "Other Parameters (MTX3,MTX5-D)"

6.3.13. MY4-AEC (MTX5-D only)
6.3.13.1.MY4-AEC FBS
Width
Same as 6.2.8.2. MY4-AEC FBS Width in "Other Parameters (MTX3,MTX5-D)"
Depth
Same as 6.2.8.2. MY4-AEC FBS Depth in "Other Parameters (MTX3,MTX5-D)"

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

82

7. Parameter List
7.1. MTX3/MTX5-D
Model

Access ID
MemNo
ElmNo
Xpos
Ypos
MTX3 MTX5-D (Memory UniqueId (Element
(X Position) (Y Position)
Number)
Number)
o
o 512
50000 0
0-7
0
(1-8ch)
o
o
o

PrmNo
(Parameter
Number)
0
1

IndexNo
Category
(Index
Number)
0
INPUT PORT

0

20001 0

0

0-21
0
(0-7:1-8ch
8-13:STIN1L-3R
14-21:9-16Ch
"DIRECT INPUT
CH")
0-7
(1-8ch)
0-21
(0-7:9-16ch
8-13:STIN1L-3R
14-21:17-24Ch
"DIRECT INPUT
CH")
0
0

0

INPUT PATCH

0

INPUT
INPUT
GAIN/
CHANNEL CHANNEL HPF
CH
1-8(16)

20003

o

o
o
o
o
o
o
o
o
o
o
o
o
o

20002 0
20005
20006
20002 0
20005
20006
20002 1
20005
20006
20002 1
20005
20006
20004 0
20007
20008

o
20004 0

o
o
o
o
o
o
o
o
o
o
o
o
o
o
o

Summing STEREO SUM

0

20004

o

INPUT
PORT
SETUP

0

20007

0-7
(1-8ch)

0-7
(9-16ch)
0-7
0
(1-8ch)
0-7
(9-16ch)
0-7
0
(1-8ch)
0-7
(9-16ch)
0-7
0
(1-8ch)

0-7
(1-8ch)

0

1

0

0

INPUT InputPatch In
PATCH 30(62)
Input x
22(30)
Output

PreInput
Section

In

HPF

3BAND
EQ

PEQ
PEQ
8(16)
Channel 3
Band

dB
-

Patch NONE YDIF IN 16
(SLOT
16)

Remarks

0:OFF
1:ON
0:STEREO
1:SUM
* Not saved to
presets
* See "6.2.1.
INPUT
PATCH" in
"6. Parameter
Values"

Phase OFF

ON

-

0:OFF
1:ON

D.Gain -96.0

24.0

dB

dB x 10
ex. -14.5dB x
10 = -145

Frequency 20.0

20.0k

Hz

Hz x 1000
ex. 1000Hz
x 1000 =
1000000

On

OFF

ON

-

0:OFF
1:ON

Q(*)

63.0

0.1

-

* Valid only for
PEQ
* See "6.2.2.1.
3BAND EQ" in
"6. Parameter
Values"
* (100 : Other
than Band A)
Hz x 1000
ex. 1000Hz x
1000 = 1000000
* Not adjustable
for HPF/LPF
dB x 10
ex. -14.5dB x 10
= -145
0:OFF
1:ON

0

Frequency 20.0(*) 20.0k

Hz

2

0

Gain(*) -18.0

18.0

dB

3

0

Bypass OFF

ON

-

0-7
(9-16ch)
0-7
0, 2
4
(1-8ch) (0:Band A
2:Band C)
0-7

0

Type

LPF

-

* See "6.2.2.1.
3BAND EQ" in
"6. Parameter
Values"

0

0

Property PEQOn OFF

ON

-

0:ON
1:OFF

20004 0

0-7
(1-8ch)

20008

0-7
(9-16ch)

20004 0
20007
20008

0-7
(1-8ch)

20004 1
20007
20008

0

Port

66
ON

unit

1

0-7
(9-16ch)

20004 0
20007
20008

0

0-7
(9-16ch)
0-7
0-2
0
(1-8ch) (0:Band A
1:Band B
0-7
(9-16ch) 2:Band C)

20008

20007

1

Internal
ST input
3ch AD

-6
OFF

MAX

Gain
+48V

0-2

o

MIN

INTERNAL Internal
Ch
HA
Head Amp
8ch AD

50001 0
o

o

Parameter Name

(9-16ch)
0-7
0
(1-8ch)

PEQ

0-7
(9-16ch)

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

83

7. Parameter List
Model

Access ID
MemNo
ElmNo
Xpos
Ypos
MTX3 MTX5-D (Memory UniqueId (Element
(X Position) (Y Position)
Number)
Number)
o
512
40002 0
0-7
0
(1-8ch)
o
40000
40001
0-7
o
(9-16ch)
o
40002 0
0-7
0
(1-8ch)
o
40000
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o

40001
40002 0
40000
40001
40002 0
40000
40001
40002 0
40000
40001
40002 1
40000
40001
40000 0
40002
40003
40000 0
40002
40003
40000 0
40002
40003
40000 0
40002
40003
40000 0
40002
40003
40000 0
40002
40003
40000 1
40002
40003
40005 0

o
o

40004
40005 0

o
o
o
o

40004
40005 2

o
o

40004
40005 2

o
o

40004
40005 2

o
o

40004

Remarks

0

dB

2

0

Attack 0

120

ms

3

0

Decay 3.2m

42.600 s

4

0

Hold

0.02m 1.96

s

* See "6.2.2.2.
GATE" in "6.
Parameter
Values"

0

0

ON

On

OFF

ON

-

0:OFF
1:ON

0

0

COMPRESSOR Compressor Dyn
8(16)
Channel

Threshold -54

0

dB

1

0

Ratio

1.0:1

∞:1

-

* See "6.2.2.3.
COMPRESSOR"
in "6. Parameter
Values"

2

0

Knee

HARD 5

-

* See "6.2.2.3.
COMPRESSOR"
in "6. Parameter
Values"

3

0

Attack 0

120

4

0

Release 3.2m

42.600 s

* See "6.2.2.2.
GATE" / Decay
in "6. Parameter
Values"

5

0

Gain

0.0

18.0

dB

dB x 10
ex. 5.2dB x 10
= 52

0

0

On

OFF

ON

-

0:OFF
1:ON

0

0

Feedback Dynamic Auto OFF
Suppressor
Detect
4(8)
Channel

ON

-

0:OFF
1:ON

1

0

Clear

ON

-

Write 1 to start
the clear process.
When the process
finishes, the value
automatically
returns to 0.

0-6
0
(Freq1-7)

0

DynFilter Frequency 20.0

20.0k

Hz

read-only
parameter

0

0

0

Fixed

OFF

ON

-

0:OFF
1:ON

0

1

0

Detect OFF

ON

-

0:OFF
1:ON

0

2

0

Clear

ON

-

Write 1 to start
the clear process.
When the process
finishes, the value
automatically
returns to 0.

0-7
(9-16ch)
0-7
0
(1-8ch)
0-7
(9-16ch)
0-7
0
(1-8ch)
0-7
(9-16ch)
0-7
0
(1-8ch)
0-7
(9-16ch)
0-7
0
(1-8ch)
0-7
(9-16ch)
0-7
0
(1-8ch)
0-7
(9-16ch)
0-7
0
(1-8ch)
0-7
(9-16ch)
0-3
0
(1-4ch)
0-7
(1-8ch)
0-3
0
(1-4ch)

0-3
(1-4ch)
0-7
(1-8ch)
0-3
(1-4ch)
0-7
(1-8ch)
0-3
(1-4ch)
0-7
(1-8ch)
0-3
(1-4ch)

unit

Range -70

0-7
(9-16ch)
0-7
0
(1-8ch)

Dyn

MAX

0

0-7
(9-16ch)
0-7
0
(1-8ch)

Gate
8(16)
Channel

MIN

dB

0-7
(9-16ch)
0-7
0
(1-8ch)

40005 1

1

Parameter Name

0

0-7
(9-16ch)
0-7
0
(1-8ch)

0-7
(1-8ch)

IndexNo
Category
(Index
Number)
0
INPUT
INPUT
GATE
CHANNEL CHANNEL
CH
1-8(16)

Threshold -72

0-7
(9-16ch)
0-7
0
(1-8ch)

40004

PrmNo
(Parameter
Number)
0

ON

FBS

On

OFF

OFF

* See "6.2.2.2.
GATE" in "6.
Parameter
Values"

ms

0-7
(1-8ch)

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

84

7. Parameter List
Model

Access ID
MemNo
ElmNo
Xpos
Ypos
MTX3 MTX5-D (Memory UniqueId (Element
(X Position) (Y Position)
Number)
Number)
512
40005 3
0-3
0-6
o
(1-4ch) (Freq1-7)
40004
0-7
o
(1-8ch)
40004 0
0-3
0
o
(1-4ch)
40005
0-7
o
(1-8ch)
40004
0-3
o
(1-4ch)
40005
0-7
o
(1-8ch)
40004
0-3
o
(1-4ch)
40005
0-7
o
(1-8ch)
40004 1
0-3
0
o
(1-4ch)
40005
0-7
o
(1-8ch)
60000 0
0-7
0
(1-8ch)
o

1

Level

2

Readable.
Writing is also
possible.

s

* See "6.2.2.4.
AGC" in "6.
Parameter
Values"

5

-

Noise OFF
Gate
On

ON

-

0:OFF
1:ON

On

OFF

ON

-

0:OFF
1:ON

Fader Level

-∞

10.00 dB

dB x 100
ex.-73.60dB x
100 = -7360
"setr" command
is available for
this parameter

On

OFF

ON

-

0:OFF
1:ON

-

Notification
only

ON

-

24.0

dB

0.1

-

CH * Ins.Out
->SLOT OUT *
CH * Ins.In ->
SLOT In *
dB x 10
ex. -14.5dB x
10 = -145
* See "6.2.2.1.
3BAND EQ" in
"6. Parameter
Values"
*(100 : Other
than Band A)
Hz x 1000
ex. 1000Hz x
1000 = 1000000

On

1

Hz

0

0

0

Channel Channel
Name
Name
8(16)
Channel

0

0

Insert

0

0
0

0

0-2
0
(0:Band A
1:Band B
2:Band C)
1

0

Frequency 20.0(*) 20.0k

Hz

0

2

0

Gain(*) -18.0

18.0

dB

* Not adjustable
for HPF/LPF
dB x 10
ex. -14.5dB x
10 = -145

0

3

0

Bypass OFF

ON

-

0

0, 2
4
(0:Band A
2:Band C)

0

Type

LPF

-

1

0

0

Property PEQOn OFF

ON

-

0:OFF
1:ON
* See "6.2.2.1.
3BAND EQ" in
"6. Parameter
Values"
0:ON
1:OFF

20033 0

30000 0
30001 0

o

Compensator Response 100m 5.0
Time

INPUT
Fader
CHANNEL 8(16)
LEVEL
Channel

0-7
0
(1-8ch)
0-15
(1-16ch)
0-7
0
(1-8ch)
0-15
(1-16ch)
0-15
0
(1-16ch)
0-5
(STIN1L3R)
0-5
(STIN1L3R)

0

STEREO
INPUT
CHANNEL
STIN
1L-3R

GAIN/
HPF
3BAND
EQ

On

ChName Name Charactor
(UTF-8)
48byte

Insert
Insert Insert OFF
with MY
card 16
Channel
Digital
Ch
D.Gain -96.0
Gain 6
Channel
PEQ 6
PEQ Q(*)
63.0
Channel 3
Band

o

o

o

o

o

o

o

o

o

Remarks

0

o

o

AutoGain
Control
4(8)
Channel

AGC

20.0k

unit

0-15
(1-16ch)

o

o

0

Frequency 20.0

MAX

0

70000 0

o

0

Feedback Fixed
Suppressor Filter
4(8)
Channel

MIN

0

o

o

Parameter Name

0

60001 0

o

IndexNo
Category
(Index
Number)
0
INPUT
INPUT
FBS
CHANNEL CHANNEL
CH
1-8(16)

0

o
o

PrmNo
(Parameter
Number)
0

0

PEQ

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

85

7. Parameter List
Model

Access ID
MemNo
ElmNo
Xpos
Ypos
MTX3 MTX5-D (Memory UniqueId (Element
(X Position) (Y Position)
Number)
Number)
o
512
40001 0
0-3
0
(STIN1Lo
40006
2R)
40001 0
0
o
o

o
o
o
o
o

o
o

120

0

4

0

Release 3.2m

42.600 s

0

5

0

Gain

0.0

18.0

dB

0

0

0

On

OFF

ON

-

0:OFF
1:ON

0

0

* See "6.2.2.4.
AGC" in "6.
Parameter Values"

1

0

AutoGain Compensator Response 100m 5.0
Control
Time
4 Channel
Level 1
5

s

0

0-3
0
(STIN1L2R)
0

40003
40007
40003
40007
40003
40007
60000

0

0

2

0

1

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

o
70004 0
60000 0
o

o
60001 0
o

o
70000 0

o
o

-

ms

40006

60001 0

o

HARD 5

70003

* See "6.2.2.3.
COMPRESSOR"
in "6. Parameter
Values"
* See "6.2.2.3.
COMPRESSOR"
in "6. Parameter
Values"

Attack 0

o

o

-

0

o

o

∞:1

3

40007

o

1.0:1

Remarks

0

40001 0
40006
40001 0

o

o

Ratio

40006

40001 1
40006
40003 0

o

dB

unit

Knee

o

o

0

MAX

0

40006

o

Threshold -54

MIN

2

o
o

IndexNo
Category
Parameter Name
(Index
Number)
0
INPUT
STEREO COMPRESSOR Compressor Dyn
CHANNEL INPUT
4 Channel
CHANNEL
0
STIN
1L-3R

0

40001 0

o

1

40006
40001 0

o

PrmNo
(Parameter
Number)
0

8-13
(ST IN
1L-ST
IN 3R)
16-21
(ST1LST3R)
8-13
(ST1LST3R)
16-21
(ST1LST3R)
0-5
(ST1LST3R)
14-21
(9-16Ch
"DIRECT
INPUT
CH")
22-29
(17-24Ch
"DIRECT
INPUT
CH")
14-21
(9-16Ch
"DIRECT
INPUT
CH")
22-29
(17-24Ch
"DIRECT
INPUT
CH")
8-15
(9-16ch)
0-7
(17-24ch)

On
AGC

Channel Channel
Name
Name 3
Channel
DIRECT
INPUT
Fader 8
INPUT
CHANNEL Channel
CHANNEL LEVEL
CH 9 - 16
(17 - 24)

Channel Channel
Name
Name 8
Channel

-

Noise OFF
GateOn

ON

-

0:OFF
1:ON

On

OFF

ON

-

0:OFF
1:ON

Fader Level

-∞

10.00 dB

dB x 100
ex.-73.60dB x
100 = -7360
"setr" command
is available for
this parameter

On

OFF

ON

0:OFF
1:ON

On
INPUT
Fader 6
CHANNEL Channel
LEVEL

* See "6.2.2.2.
GATE" / Decay
in "6. Parameter
Values"
dB x 10
ex. 5.2dB x 10
= 52

On

-

ChName Name Charactor
(UTF-8)
48byte
Fader Level -∞
10.00 dB

Notification
only

On

-

0:OFF
1:ON

-

Notification
Only

On

OFF

ON

ChName Name Charactor
(UTF-8)
48byte

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

dB x 100
ex.-73.60dB x
100 = -7360
"setr" command
is available for
this parameter

86

7. Parameter List
Model

Access ID
MemNo
ElmNo
PrmNo IndexNo
Category
Xpos
Ypos
MTX3 MTX5-D (Memory UniqueId (Element
(Parameter (Index
(X Position) (Y Position)
Number)
Number)
Number) Number)
512
20008 0
0-3
0
0
0
INPUT
EFFECT
o
(Fx.RTN1L
CHANNEL ST
20014
o
- 2R)
RETURN
1L-2R
o
20008 1
o
o

o

20014
70004 0
60000 1

o

o

2
o

0

0

0

0

0-21
0-7
(0-7:1-8ch
(A-H)
8-13:ST1L-ST3R
14-21:9-16Ch
"DIRECT INPUT
CH")
0-29
(0-15:1-16ch
16-21:ST1L-ST3R
22-29:17-24Ch
"DIRECT INPUT
CH")
0

0

0

0

EFFECT Fader 4
ST
Channel
RETURN

MIN

MAX

unit

-∞

10.00 dB

dB x 100
ex.-73.60dB x
100 = -7360

On

OFF

ON

-

0:OFF
1:ON

Charactor
(UTF-8)
48byte
OFF ON

-

On

Channel Channel
ChName Name
Name
Name 2
Channel
INPUT
INPUT
INPUT
DCA Assign
CHANNEL CHANNEL CHANNEL Assign On
DCA
DCA
DCA

Group Level
Master

o

o

o

2
50011 0

o

o

o

o
1

o
o

0-3
(0-3:CH1-4)

-∞

-

o

dB x 100
ex.-73.60dB x
100 = -7360
"setr" command
is available for
this parameter

INPUT
INPUT
DCA Mute DCA Assign OFF
CHANNEL CHANNEL
Assign On
MUTE
MUTE

ON

-

0:OFF
1:ON

Group MuteOn OFF
Master
Auto Mixer Master Override OFF
4 (8)
Channel

ON

-

ON

-

0:OFF
1:ON
0:OFF
1:ON

ON

-

0:OFF
1:ON

Auto

-

* See "6.2.2.5.
DUGAN
AUTOMIXER" in
"6. Parameter
Values"
* See "6.2.2.5.
DUGAN
AUTOMIXER" in
"6. Parameter
Values"
* See "6.2.2.5.
DUGAN
AUTOMIXER" in
"6. Parameter
Values"
0:OFF
1:ON

o
o
o

Dugan
Dugan
Auto Mixer AUTO
MIXER

1

0

Mute

Ch

OFF

Mode* Mute

1

Weight -100.0 15.0

dB

2

Group* a

-

0-7
(0-7:CH1-8)
0-3
(0-3:CH1-4)

o

0

0-7
(0-7:CH1-8)
0-3
(0-3:CH1-4)
0-7
(0-7:CH1-8)

b
d

3

0:OFF
1:ON

10.00 dB

0-7
(0-7:CH1-8)
0-3
(0-3:CH1-4)

o

0-1
(0:a
1:b)
0-3
(0:a
1:b
2:c
3:d)
0-1
(0:a
1:b)
0-3
(0:a
1:b
2:c
3:d)
0

0

Remarks

Fader Level

o

60001 1

o

6-7
0
(FxRtn1,
FxRtn2)
0-21
0-7
(0-7:1-8ch
(A-H)
8-13:ST1L-ST3R
14-21:9-16Ch
"DIRECT INPUT
CH")
0-29
(0-15:1-16ch
16-21:ST1L-ST3R
22-29:17-24Ch
"DIRECT INPUT
CH")
0

Parameter Name

Override OFF

ON

-

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

87

7. Parameter List
Model

Access ID
MemNo
ElmNo
PrmNo IndexNo
Category
Xpos
Ypos
MTX3 MTX5-D (Memory UniqueId (Element
(Parameter (Index
(X Position) (Y Position)
Number)
Number)
Number) Number)
512
20006 0
0-1
0
1
0
EFFECT
o
(Effect1-2)
20013
o
20006 1

o
o

20013

o

20013

20006

o

20006

o
o

o

Reverb Vocal Hall
Echo

Remarks
* See "6.2.3.
EFFECT" in "6.
Parameter Values"

10.0

s

* See "6.2.3.
EFFECT" in "6.
Parameter Values"

1

RevStage 0.3
Time

10.0

s

* See "6.2.3.
EFFECT" in "6.
Parameter Values"

2

Karaoke 0.4
Time

400

ms

* See "6.2.3.
EFFECT" in "6.
Parameter Values"

3

Vocal 0.4
Time

400

ms

* See "6.2.3.
EFFECT" in "6.
Parameter Values"

Level

0.00

dB

dB x 100
ex.-73.60dB x
100 = -7360
"setr" command
is available for
this parameter

0

1

0-33
0-15
0
(0-15:CH1-16
(MATRIX1-16
16-21:STIN1L-3R SEND)
22-29:CH17-24
30-33:FxRt1L-2R)

0

1

0-25
0-7
1
(0- 7:CH1-8
(MATRIX1-8
8-13:STIN1L-3R SEND)
14-21:CH9-16
22-25:FxRt1L-2R)

0

0-33
0-15
1
(0-15:CH1-16
(MATRIX1-16
16-21:STIN1L-3R SEND)
22-29:CH17-24
30-33:FxRt1L-2R)

0

1

unit

Simple RevHall 0.3
Effect Time

0-25
0-7
0
(0- 7:CH1-8
(MATRIX1-8
8-13:STIN1L-3R SEND)
14-21:CH9-16
22-25:FxRt1L-2R)

o

MAX

0

30002 1

o

MIN

Effect Type

20013

o

o

EFFECT Effect

20013
20006

o

Parameter Name

MATRIX

MATRIX MATRIX
SEND
(ZONE
OUT
MONO)
26(34)
Input x
8(16)
Output

Ch

-∞

When Input
channels are
set as Stereo,
Send to Matrix
parameters for
Stereo Input
channels are
linked.
On

OFF

ON

-

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

0:OFF
1:ON
When Input
channels are
set as Stereo,
Send to Matrix
parameters for
Stereo Input
channels are
linked.

88

7. Parameter List
Model

Access ID
MemNo
ElmNo
PrmNo IndexNo
Category
Xpos
Ypos
MTX3 MTX5-D (Memory UniqueId (Element
(Parameter (Index
(X Position) (Y Position)
Number)
Number)
Number) Number)
512
30002 1
0-25
0-7
0
0
MATRIX
(0- 7:CH1-8
(MATRIX1-8
8-13:STIN1L-3R SEND)
14-21:CH9-16
22-25:FxRt1L-2R)
o

1

0-33
0-15
0
(0-15:CH1-16
(MATRIX1-16
16-21:STIN1L-3R SEND)
22-29:CH17-24
30-33:FxRt1L-2R)

0

0-25
0-7
1
(0- 7:CH1-8
(MATRIX1-8
8-13:STIN1L-3R SEND)
14-21:CH9-16
22-25:FxRt1L-2R)

0

0-33
0-15
1
(0-15:CH1-16
(MATRIX1-16
16-21:STIN1L-3R SEND)
22-29:CH17-24
30-33:FxRt1L-2R)

0

1

0-25
0-7
2
(0- 7:CH1-8
(MATRIX1-8
8-13:STIN1L-3R SEND)
14-21:CH9-16
22-25:FxRt1L-2R)

0

1

0-33
0-15
2
(0-15:CH1-16
(MATRIX1-16
16-21:STIN1L-3R SEND)
22-29:CH17-24
30-33:FxRt1L-2R)

0

0-21
(0- 7:CH1-8
8-13:STIN1L-3R
14-21:CH9-16)
0-29
(0- 15:CH1-16
16-21:STIN1L-3R
22-29:CH17-24)
0-21
( 0- 7:CH1-8
8-13:STIN1L-3R
14-21:CH9-16 )
0-29
(0- 15:CH1-16
16-21:STIN1L-3R
22-29:CH17-24)

0-3
0
(0:FX 1 SEND
1:FX 2 SEND
2:ANC 1 SEND
3:ANC 2 SEND)

0

1

0

Parameter Name
MATRIX MATRIX Ch
SEND
(ZONE
OUT
STEREO)
26(34)
Input x
8(16)
Output

MIN
Level

-∞

MAX
0.00

unit
dB

When Input
channels are
set as Stereo,
Send to
Stereo Matrix
parameters for
Stereo Input
channels (i.e.
four parameters
in total) are
linked.
On

OFF

ON

-

When Input
channels are
set as Stereo,
Send to
Stereo Matrix
parameters for
Stereo Input
channels (i.e.
four parameters
in total) are
linked.

o

o

o

20010 0
o
20017 0
o
20010 0
o
20017 0
o

0:OFF
1:ON
When Input
channels are
set as Mono,
Send to
Stereo Matrix
parameters
for Mono Input
channels (i.e.
two parameters
in total) are
linked.

o

1

dB x 100
ex.-73.60dB x
100 = -7360
"setr" command
is available for
this parameter
When Input
channels are
set as Mono,
Send to
Stereo Matrix
parameters
for Mono Input
channels (i.e.
two parameters
in total) are
linked.

o

1

Remarks

FX/ANC Matrix
SEND
Mixer
22(30)
Input 4
Output

Ch

Pan

L63

R63

-

-63 :L63
0:C
63:R63
e.g. L31 = -31
Valid only for
odd channels
and available
only when
destination
Matrix channels
are paired.

Level

-∞

0.00

dB

dB x 100
ex.-73.60dB x
100 = -7360
"setr" command
is available for
this parameter

On

OFF

ON

-

0:OFF
1:ON

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

89

7. Parameter List
Model

Access ID
MemNo
ElmNo
Xpos
Ypos
MTX3 MTX5-D (Memory UniqueId (Element
(X Position) (Y Position)
Number)
Number)
512
50013 0
0
0-4
(0:1st MIC
1:MIC 2
o
2:MIC 3
3:MIC 4
4:SD)
o
50012 0
0
0
2
0
0

PrmNo
(Parameter
Number)
0

IndexNo
Category
(Index
Number)
0
ZONE ZONE
OUT
1-8(16)

0
0

0

Parameter Name
PAGING Router 48 In
Input 6
Output

MIN

MAX

unit

Patch None

ANC BUS 2

On
OFF
Range -∞

ON
0.0

dB

1

Attack 0.0

10.0

s

2

Release 0.0

10.0

s

ON

-

PAGING
16ch

On
Gain

o

o
o
9

o

20011 0
o

20018
o

o
o
o
o
o
o
o
o

20012 0
20019
20012
20019
20012
20019
20012

0-15
0-23
0
(ZONE1-16) (ZONE
GROUP1-24)
0
0-7
0
(0:ZONE1
2nd
PRIORITY
PRIORITY
SOURCE
:
7:ZONE8
2nd
PRIORITY
PRIORITY
SOURCE)
0-7
0
0
(ZONE1-8)

o

o
o
o

ANC BUS 2

Threshold -54

0

dB

1

Range -70

0

dB

2

Attack 0

240

ms

3

Release 3.2m

42.600 s

4

Hold

PRIORITY Dyn
DUCKER

0

Source Level

20012
20019
20011 0

20018

1
0

8-15
0
(8:ZONE1
1st
PRIORITY
PRIORITY
SOURCE
:
15:ZONE8
1st
PRIORITY
PRIORITY
SOURCE)

On
0

1st
PRIORITY In
PRIORITY SOURCE

* See "6.2.4.1.
PAGING" in
"6. Parameter
Values"

* See "6.2.4.1.
PAGING" in
"6. Parameter
Values"
s x 10
ex. 5.3s x 10
= 53
s x 10
ex. 5.3s x 10
= 53

* See "6.2.4.2.
1st/2nd
PRIORITY" in
"6. Parameter
Values"

* See "6.2.2.2.
GATE" /
Decay in "6.
Parameter
Values"
* See "6.2.2.2.
GATE" in "6.
Parameter
Values"

0.02m 1.96

s

-∞

0.00

dB

dB x 100
ex.-73.60dB x
100 = -7360
"setr" command
is available for
this parameter

OFF

ON

-

0:OFF
1:ON

20019

o

o

Patch None

0

2nd
PRIORITY In
PRIORITY SOURCE

20019
20012 1

o

0

20019
20012

o

Zone ZoneOn OFF
Group

Remarks

Patch None

ANC BUS 2

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

* See "6.2.4.2.
1st/2nd
PRIORITY" in
"6. Parameter
Values"

90

7. Parameter List
Model

Access ID
MemNo
ElmNo
Xpos
Ypos
MTX3 MTX5-D (Memory UniqueId (Element
(X Position) (Y Position)
Number)
Number)
o
512
20013 0
0-7
0
(ZONE1-8)
o
20020
o
20013
o
20020
o
20013
o
20020
20013
o
o

o

o
o
o

20013
20020
20011 0

20014 0

0

o

o

o

o
o
o
o
o
o

240

ms

3

Release 3.2m

42.600 s

4

Hold

Source Level

On
ANC
In
SOURCE

0.02m 1.96

s

-∞

0.00

dB

dB x 100
ex.-73.60dB x
100 = -7360
"setr" command
is available for
this parameter

OFF

ON

-

0:OFF
1:ON

Patch None

0.00

dB

dB x 100
ex.-73.60dB x
100 = -7360
"setr" command
is available for
this parameter

Threshold -∞

0.00

dB

dB x 100
ex.-73.60dB x
100 = -7360
"setr" command
is available for
this parameter

1

Time

0.1

5.0

s

sec x 10
ex. 3.8sec x 10
= 38

0

Program Max
Gain

0.0

18.0

dB

dB x 10
ex. 5.2dB x 10
= 52

1

Min
Gain

-18.0

0.0

dB

dB x 10
ex. -14.5dB x
10 = -145

2

Ratio

0.5:1

2.0:1

-

* See "6.2.4.3.
ANC" in "6.
Parameter
Values"

3

Response 1
Time

60

s

On

OFF

ON

-

Fader Level

-∞

10.00 dB

dB x 100
ex.-73.60dB x
100 = -7360
"setr" command
is available for
this parameter

On

OFF

ON

-

0:OFF
1:ON

-

Notification
Only

Ambient
Ambient Threshold -∞
Noise
Compensator
8 Channel

Gap

20021
20014
20021
20014 3
20021
60002 0

0
0-7
0
(ZONE1-8)

On

0

0

0

0

0

0

MATRIX Fader
OUTPUT 8(16)
MASTER Channel

0-15
(ZONE1-16)

70001 0
70005

0-7
0
(ZONE1-8)
0-15
(ZONE1-16)
0-7
0
(ZONE1-8)
0-7
(ZONE9-16)

* See "6.2.2.2.
GATE" /
Decay in "6.
Parameter
Values"
* See "6.2.2.2.
GATE" in "6.
Parameter
Values"

* See "6.2.4.2.
1st/2nd
PRIORITY" in
"6. Parameter
Values"

0

ANC

Remarks

ANC BUS 2

0

0

20021

o

o

Attack 0

20021

60003 0

o

2

20021

o
o

dB

20021

20014

o

0

0

20014

o

Range -70

20021

20014 2

o

o

0-7
0
(ZONE1-8)

20014

o

dB

16-23
0
(16:ZONE1
ANC
AMBIENT
SOURCE
:
23:ZONE8
ANC
AMBIENT
SOURCE)

20014 1

o

unit

0

1

20018

o

MAX

20020

o

o

MIN
Threshold -54

1

1st
PRIORITY Dyn
PRIORITY DUCKER

0

o

o

Parameter Name

20020
20013 1

o

IndexNo
Category
(Index
Number)
0
ZONE ZONE
OUT
1-8(16)

20020
20013

o

PrmNo
(Parameter
Number)
0

Channel Channel
Name
Name
8(16)
Channel

On

ChName Name Charactor
(UTF-8)
48byte

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

0:OFF
1:ON

91

7. Parameter List
Model

Access ID
MemNo
ElmNo
Xpos
Ypos
MTX3 MTX5-D (Memory UniqueId (Element
(X Position) (Y Position)
Number)
Number)
512
60002 1
0-7
0-7
o
(ZONE1-8) (A-H)
0-15
o
(ZONE1-16)
2
0
0-7
(A-H)
o

IndexNo
Category
(Index
Number)
0
ZONE ZONE
DCA/
MUTE
1-8(16)

Parameter Name
ZONE
OUT
DCA

DCA
Fader
8(16)
Channel

0

MIN

MAX

unit

DCA Assign OFF
Assign On

ON

Group Level
Master

10.00 dB

-∞

-

o

60003 1

o
o
o

PrmNo
(Parameter
Number)
0

2

o

20016 1

o
o

20023
20016 1

o
o

20023
50002 0

o

o

o

o

o

o

o

o

0-7
0-7
(ZONE1-8) (A-H)
0-15
(ZONE1-16)
0
0-7
(A-H)
0
0-7
(OUT1-8)
0-15
(OUT1-16)
0
0-7
(OUT1-8)
0-15
(OUT1-16)
0
0

0

0

ZONE
OUT
MUTE

DCA Mute DCA Assign OFF
8(16)
Assign On
Channel

0
0

0

0

0

0

ROUTER

ROUTOR Bus Out
Router
24(32)
Input x
8(16)
OSCILLATOR
Output

OSCILLATOR Oscillator
Mono

ON

-

Remarks
0:OFF
1:ON

dB x 100
ex.-73.60dB x
100 = -7360
"setr" command
is available for
this parameter
0:OFF
1:ON

Group MuteOn OFF ON
Master
In
Patch NONE YDIF
OUT
16

-

OSC On
Patch

OFF

ON

-

0:OFF
1:ON

Oscillator Level

-∞

0

dB

OFF

ON

-

dB x 100
ex.-73.60dB x
100 = -7360
"setr" command
is available for
this parameter
0:OFF
1:ON
Hz x 1000
ex. 1000Hz x
1000 = 1000000
* See "6.2.5.2.
OSCILLATOR"
in "6. Parameter
Values"

-

1

On

2

Vari
20.0(*) 20.0k
Frequency

Hz

3

Wave
form(*)

-

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

0:OFF
1:ON
* See "6.2.5.1.
ROUTER" in
"6. Parameter
Values"

92

7. Parameter List
Model

Access ID
MemNo
ElmNo
PrmNo IndexNo
Category
Xpos
Ypos
MTX3 MTX5-D (Memory UniqueId (Element
(Parameter (Index
(X Position) (Y Position)
Number)
Number)
Number) Number)
512
20017 0
0-7
0
0
0
OUTPUT OUTPUT
OUTPUT
o
(OUT1-8)
CHANNEL CH STRIP CHANNEL
1-8(16)
LEVEL
(1way/2way)
20024
0-15
o
(OUT1-16)
20017 1

o
o
o

o
o

20024
70002 0
70006
20018 0

o
o

20025
20018 0

o
o

20025
20019 0

o
o

20026
20019 0

o
o
o
o
o
o

20026

0-15
(OUT1-16)

20019 0

0-7
(OUT1-8)

20026

0-15
(OUT1-16)

20019 0

0-7
(OUT1-8)
0-15
(OUT1-16)
0-7
(OUT1-8)
0-15
(OUT1-16)
0-7
(OUT1-8)
0-15
(OUT1-16)
0

20026
20019 0

o
o

20026
20019 1

o
o

o

o

o

o

0-7
(OUT1-8)
0-15
(OUT1-16)
0-7
(OUT1-8)
0-7
(OUT9-16)
0-7
(OUT1-8)
0-15
(OUT1-16)
0-7
(OUT1-8)
0-15
(OUT1-16)
0-7
(OUT1-8)
0-15
(OUT1-16)
0-7
(OUT1-8)

20026
40006-40013 1
(40006:OUT1
40007:OUT2
: :
40013:OUT8)
40008-40023
(40008:OUT1
40009:OUT2
: :
40023:OUT16)
40006-40013 1
(40006:OUT1
40007:OUT2
: :
40013:OUT8)
40008-40023
(40008:OUT1
40009:OUT2
: :
40023:OUT16)

0

Parameter Name
Fader
8(16)
Channel

MIN

MAX

unit

Fader Level

-∞

10.00 dB

On

OFF

ON

On

-

Remarks
dB x 100
ex.-73.60dB x
100 = -7360
"setr" command
is available for
this parameter
0:OFF
1:ON

0

0

0

Channel Channel
Name
Name
8(16)
Channel

ChName Name Charactor
(UTF-8)
48byte

-

Notification
Only

0

0

0

DELAY

Delay On

-

0:OFF
1:ON

Delay
8(16)
Channel

1

4BAND
EQ

PEQ
PEQ
8(16)
Channel 4
Band

OFF

ON

Delay 0.00
Time

1000.00 ms

ms x 100
ex. 102.80ms x
100 = 10280

Q(*)

0.1

-

* See "6.2.2.1.
3BAND EQ" in
"6. Parameter
Values"
*(100 : Other
than Band A)
Hz x 1000
ex. 1000Hz x
1000 = 1000000
* Not adjustable
for HPF/LPF
dB x 10
ex. -14.5dB x
10 = -145
0:OFF
1:ON

0-3
0
(0:Band A
1:Band B
2:Band C
3:Band D) 1

0

63.0

0

Frequency 20.0(*) 20.0k

Hz

2

0

Gain(*) -18.0

18.0

dB

3

0

Bypass OFF

ON

-

0, 3
4
(0:Band A
3:Band D)

0

Type

LPF

-

* See "6.2.2.1.
3BAND EQ" in
"6. Parameter
Values"

0

0

0

Property PEQOn OFF

ON

-

0:ON
1:OFF

0

0

0

ON

-

0:OFF
1:ON

0

1

0

SPEAKER Speaker
Delay On
OFF
PROCESSOR Processor
1 Way
*Speaker
Processor
type (1 Way
or 2 Way) is
configurable
through
MTX Editor
software.
Delay 0.00
Time

PEQ

500.00 ms

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

ms x 100
ex. 102.80ms x
100 = 10280

93

7. Parameter List
Model

Access ID
MemNo
ElmNo
Xpos
Ypos
MTX3 MTX5-D (Memory UniqueId (Element
(X Position) (Y Position)
Number)
Number)
512
40006-40013 2
0
0
(40006:OUT1
o
40007:OUT2
: :
40013:OUT8)
40008-40023
(40008:OUT1
o
40009:OUT2
: :
40023:OUT16)
40006-40013 2
0
0
(40006:OUT1
o
40007:OUT2
: :
40013:OUT8)
40008-40023
(40008:OUT1
o
40009:OUT2
: :
40023:OUT16)
40006-40013 2
0
0
(40006:OUT1
o
40007:OUT2
: :
40013:OUT8)
40008-40023
(40008:OUT1
o
40009:OUT2
: :
40023:OUT16)
40006-40013 2
0
0
(40006:OUT1
o
40007:OUT2
: :
40013:OUT8)
40008-40023
(40008:OUT1
o
40009:OUT2
: :
40023:OUT16)
40006-40013 2
0
0
(40006:OUT1
o
40007:OUT2
: :
40013:OUT8)
40008-40023
(40008:OUT1
o
40009:OUT2
: :
40023:OUT16)
40006-40013 2
0
0
(40006:OUT1
o
40007:OUT2
: :
40013:OUT8)
40008-40023
(40008:OUT1
o
40009:OUT2
: :
40023:OUT16)
40006-40013 2
0
0
(40006:OUT1
o
40007:OUT2
: :
40013:OUT8)
40008-40023
(40008:OUT1
o
40009:OUT2
: :
40023:OUT16)

PrmNo
(Parameter
Number)
2

IndexNo
Category
(Index
Number)
0
OUTPUT OUTPUT
SPEAKER
CHANNEL CH STRIP PROCESSOR
1-8(16)
(1way/2way)

3

0

4

Parameter Name
Speaker
Band
Processor
1 Way
*Speaker
Processor
type (1 Way
or 2 Way) is
configurable
through
MTX Editor
software.

MIN

MAX

unit

Remarks

LPF
20.0
Frequency

20.0k

Hz

Hz x 1000
ex. 1000Hz
x 1000 =
1000000

HPF
20.0
Frequency

20.0k

Hz

Hz x 1000
ex. 1000Hz
x 1000 =
1000000

0

LPFType Thru

48dB/ Oct
Linkwitz

* See "6.2.6.2.
SPEAKER
PROCESSOR"
in "7. Parameter
Values"

5

0

HPFType Thru

48dB/ Oct
Linkwitz

* See "6.2.6.2.
SPEAKER
PROCESSOR"
in "7. Parameter
Values"

6

0

LPFGc(*) -6

6

dB

*Valid only for
AdjustGc

7

0

HPFGc(*) -6

6

dB

*Valid only for
AdjustGc

8

0

Polarity NORMAL INVERTED -

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

0:NORMAL
1:INVERTED

94

7. Parameter List
Model

Access ID
MemNo
ElmNo
Xpos
Ypos
MTX3 MTX5-D (Memory UniqueId (Element
(X Position) (Y Position)
Number)
Number)
512
40006-40013 4
0
0-5
(40006:OUT1
(0:Band A
o
40007:OUT2
1:Band B
: :
2:Band C
40013:OUT8)
3:Band D
4:Band E
40008-40023
5:Band F)
(40008:OUT1
o
40009:OUT2
: :
40023:OUT16)
40006-40013 4
0
(40006:OUT1
o
40007:OUT2
: :
40013:OUT8)
40008-40023
(40008:OUT1
o
40009:OUT2
: :
40023:OUT16)
40006-40013 4
0
(40006:OUT1
o
40007:OUT2
: :
40013:OUT8)
40008-40023
(40008:OUT1
o
40009:OUT2
: :
40023:OUT16)
40006-40013 4
0
(40006:OUT1
o
40007:OUT2
: :
40013:OUT8)
40008-40023
(40008:OUT1
o
40009:OUT2
: :
40023:OUT16)
40006-40013 4
0
(40006:OUT1
o
40007:OUT2
: :
40013:OUT8)
40008-40023
(40008:OUT1
o
40009:OUT2
: :
40023:OUT16)
40006-40013 5
0
0
(40006:OUT1
o
40007:OUT2
: :
40013:OUT8)
40008-40023
(40008:OUT1
o
40009:OUT2
: :
40023:OUT16)
40006-40013 5
0
0
(40006:OUT1
o
40007:OUT2
: :
40013:OUT8)
40008-40023
(40008:OUT1
o
40009:OUT2
: :
40023:OUT16)
40006-40013 5
0
0
(40006:OUT1
o
40007:OUT2
: :
40013:OUT8)
40008-40023
(40008:OUT1
o
40009:OUT2
: :
40023:OUT16)

PrmNo
(Parameter
Number)
0

IndexNo
Category
(Index
Number)
0
OUTPUT OUTPUT
SPEAKER
CHANNEL CH STRIP PROCESSOR
1-8(16)
(1way/2way)

1

0

2

Parameter Name
Speaker
PEQ
Processor
1 Way
*Speaker
Processor
type (1 Way
or 2 Way) is
configurable
through
MTX Editor
software.

MIN
Q(*)

63.0

MAX

Remarks

-

* See "6.2.2.1.
3BAND EQ" in
"7. Parameter
Values"

Frequency 20.0(*) 20.0k

Hz

*(For 500 : HORN EQ
100 : O
 ther than
Band A)
Hz x 1000
ex. 1000Hz x 1000 =
1000000

0

Gain(*) -18.0

18.0

dB

* Not
adjustable for
HPF/LPF/APF
1st/APF 2nd
dB x 10
ex. -14.5dB x
10 = -145

3

0

Bypass OFF

ON

-

0:OFF
1:ON

4

0

Type

Horn
EQ

-

* See "6.2.6.2.
SPEAKER
PROCESSOR"
in "7. Parameter
Values"

0

0

Limiter Threshold -54

0

dB

1

0

Attack 0.0

120.0 ms

ms x 10
ex. 24.5ms x
10 = 245

2

0

Release 3.2m

42.600 s

* See "6.2.2.2.
GATE" / Decay
in "7. Parameter
Values"

PEQ

0.1

unit

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

95

7. Parameter List
Model

Access ID
MemNo
ElmNo
Xpos
Ypos
MTX3 MTX5-D (Memory UniqueId (Element
(X Position) (Y Position)
Number)
Number)
512
40006-40013 5
0
0
(40006:OUT1
o
40007:OUT2
: :
40013:OUT8)
40008-40023
(40008:OUT1
o
40009:OUT2
: :
40023:OUT16)
40006-40013 5
0
0
(40006:OUT1
o
40007:OUT2
: :
40013:OUT8)
40008-40023
(40008:OUT1
o
40009:OUT2
: :
40023:OUT16)
40006-40013 5
0
0
(40006:OUT1
o
40007:OUT2
: :
40013:OUT8)
40008-40023
(40008:OUT1
o
40009:OUT2
: :
40023:OUT16)
40006-40013 6
0
0
(40006:OUT1
o
40007:OUT2
: :
40013:OUT8)
40008-40023
(40008:OUT1
o
40009:OUT2
: :
40023:OUT16)
40006-40013 6
0
0
(40006:OUT1
o
40007:OUT2
: :
40013:OUT8)
40008-40023
(40008:OUT1
o
40009:OUT2
: :
40023:OUT16)
40006-40013 6
0
0
(40006:OUT1
o
40007:OUT2
: :
40013:OUT8)
40008-40023
(40008:OUT1
o
40009:OUT2
: :
40023:OUT16)

PrmNo
(Parameter
Number)
3

IndexNo
Category
(Index
Number)
0
OUTPUT OUTPUT
SPEAKER
CHANNEL CH STRIP PROCESSOR
1-8(16)
(1way/2way)

4

0

5

0

0

0

1

2

Parameter Name

MIN

Speaker
Limiter On
OFF
Processor
1 Way
*Speaker
Processor
type (1 Way
or 2 Way) is
configurable
through
MTX Editor
software.
Attack Fast
Mode

MAX
ON

unit
-

Remarks
0:OFF
1:ON

Manual -

* See "6.2.6.2.
SPEAKER
PROCESSOR"
in "7. Parameter
Values"

Release Fast
Mode

Manual -

* See "6.2.6.2.
SPEAKER
PROCESSOR"
in "7. Parameter
Values"

Level

-∞

10.00 dB

dB x 100
ex.-73.60dB x
100 = -7360
"setr" command
is available for
this parameter

0

Mute

UNMUTED MUTED -

0

PEQOn OFF

Out

ON

-

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

0:UNMUTED
1:MUTED

0:ON
1:OFF

96

7. Parameter List
Model

Access ID
MemNo
ElmNo
Xpos
Ypos
MTX3 MTX5-D (Memory UniqueId (Element
(X Position) (Y Position)
Number)
Number)
512
40014-40017 1
0-1
0
(40014:OUT1
(0:LOW
o
40015:OUT3
1:HIGH)
: :
40017:OUT7)
40024-40031
(40024:OUT1
o
40025:OUT3
: :
40031:OUT15)
40014-40017 1
0
(40014:OUT1
o
40015:OUT3
: :
40017:OUT7)
40024-40031
(40024:OUT1
o
40025:OUT3
: :
40031:OUT15)
40014-40017 2
0
0
(40014:OUT1
(0:LOW)
o
40015:OUT3
: :
40017:OUT7)
40024-40031
(40024:OUT1
o
40025:OUT3
: :
40031:OUT15)
40014-40017 2
0-1
0
(40014:OUT1
(0:LOW
o
40015:OUT3
1:HIGH)
: :
40017:OUT7)
40024-40031
(40024:OUT1
o
40025:OUT3
: :
40031:OUT15)
40014-40017 2
0
0
(40014:OUT1
(0:LOW)
o
40015:OUT3
: :
40017:OUT7)
40024-40031
(40024:OUT1
o
40025:OUT3
: :
40031:OUT15)
40014-40017 2
0-1
0
(40014:OUT1
(0:LOW
o
40015:OUT3
1:HIGH)
: :
40017:OUT7)
40024-40031
(40024:OUT1
o
40025:OUT3
: :
40031:OUT15)
40014-40017 2
0
0
(40014:OUT1
(0:LOW)
o
40015:OUT3
: :
40017:OUT7)
40024-40031
(40024:OUT1
o
40025:OUT3
: :
40031:OUT15)
40014-40017 2
0-1
0
(40014:OUT1
(0:LOW
o
40015:OUT3
1:HIGH)
: :
40017:OUT7)
40024-40031
(40024:OUT1
o
40025:OUT3
: :
40031:OUT15)

PrmNo
(Parameter
Number)
0

IndexNo
Category
(Index
Number)
0
OUTPUT OUTPUT
SPEAKER
CHANNEL CH STRIP PROCESSOR
1-8(16)
(1way/2way)

1

0

2

0

3

Parameter Name

MIN

Speaker
Delay On
OFF
Processor
2 Way
*Speaker
Processor
type (1 Way
or 2 Way) is
configurable
through
MTX Editor
software.
Delay 0.00

MAX
ON

unit
-

Remarks
0:ON
1:OFF

500.00 ms

ms x 100
ex. 102.80ms x
100 = 10280

LPF
20.0
Frequency

20.0k

Hz

Hz x 1000
ex. 1000Hz
x 1000 =
1000000

0

HPF
20.0
Frequency

20.0k

Hz

Hz x 1000
ex. 1000Hz
x 1000 =
1000000

4

0

LPFType Thru

48dB/ Oct
Linkwitz

* See "6.2.6.2.
SPEAKER
PROCESSOR"
in "7. Parameter
Values"

5

0

HPFType Thru

48dB/ Oct
Linkwitz

* See "6.2.6.2.
SPEAKER
PROCESSOR"
in "7. Parameter
Values"

6

0

LPFGc(*) -6

6

dB

*Valid only for
AdjustGc

7

0

HPFGc(*) -6

6

dB

*Valid only for
AdjustGc

Band

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

97

7. Parameter List
Model

Access ID
MemNo
ElmNo
Xpos
Ypos
MTX3 MTX5-D (Memory UniqueId (Element
(X Position) (Y Position)
Number)
Number)
512
40014-40017 2
0-1
0
(40014:OUT1
(0:LOW
o
40015:OUT3
1:HIGH)
: :
40017:OUT7)
40024-40031
(40024:OUT1
o
40025:OUT3
: :
40031:OUT15)
40014-40017 3
0
0
(40014:OUT1
o
40015:OUT3
: :
40017:OUT7)
40024-40031
(40024:OUT1
o
40025:OUT3
: :
40031:OUT15)
40014-40017 4
0-1
0-5
(40014:OUT1
(0:LOW (0:Band A
o
40015:OUT3
1:HIGH) 1:Band B
: :
2:Band C
40017:OUT7)
3:Band D
4:Band E
40024-40031
5:Band F)
(40024:OUT1
o
40025:OUT3
: :
40031:OUT15)
40014-40017 4
(40014:OUT1
o
40015:OUT3
: :
40017:OUT7)
40024-40031
(40024:OUT1
o
40025:OUT3
: :
40031:OUT15)
40014-40017 4
(40014:OUT1
o
40015:OUT3
: :
40017:OUT7)
40024-40031
(40024:OUT1
o
40025:OUT3
: :
40031:OUT15)
40014-40017 4
(40014:OUT1
o
40015:OUT3
: :
40017:OUT7)
40024-40031
(40024:OUT1
o
40025:OUT3
: :
40031:OUT15)
40014-40017 4
(40014:OUT1
o
40015:OUT3
: :
40017:OUT7)
40024-40031
(40024:OUT1
o
40025:OUT3
: :
40031:OUT15)

PrmNo
(Parameter
Number)
8

IndexNo
Category
(Index
Number)
0
OUTPUT OUTPUT
SPEAKER
CHANNEL CH STRIP PROCESSOR
1-8(16)
(1way/2way)

0

0

0

0

1

0

2

Parameter Name

MIN

MAX

unit

Speaker
Band Polarity NORMAL INVERTED Processor
2 Way
*Speaker
Processor
type (1 Way
or 2 Way) is
configurable
through
MTX Editor
software.
Center Frequency 20.0
20.0k Hz

PEQ

Q(*)

63.0

0:NORMAL
1:INVERTED

Hz x 1000
ex. 1000Hz
x 1000 =
1000000

-

* See "6.2.2.1.
3BAND EQ" in
"7. Parameter
Values"

Frequency 20.0(*) 20.0k

Hz

*(For 500 : HORN EQ
100 : O
 ther than
Band A)
Hz x 1000
ex. 1000Hz x 1000 =
1000000

0

Gain(*) -18.0

18.0

dB

*Not adjustable
for HPF/LPF/
APF 1st/APF
2nd
dB x 10
ex. -14.5dB x
10 = -145

3

0

Bypass OFF

ON

-

0:ON
1:OFF

4

0

Type

Horn
EQ

-

* See "6.2.6.2.
SPEAKER
PROCESSOR"
in "7. Parameter
Values"

PEQ

0.1

Remarks

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

98

7. Parameter List
Model

Access ID
MemNo
ElmNo
Xpos
Ypos
MTX3 MTX5-D (Memory UniqueId (Element
(X Position) (Y Position)
Number)
Number)
512
40014-40017 5
0-1
0
(40014:OUT1
(0:LOW
o
40015:OUT3
1:HIGH)
: :
40017:OUT7)
40024-40031
(40024:OUT1
o
40025:OUT3
: :
40031:OUT15)
40014-40017 5
0
(40014:OUT1
o
40015:OUT3
: :
40017:OUT7)
40024-40031
(40024:OUT1
o
40025:OUT3
: :
40031:OUT15)
40014-40017 5
0
(40014:OUT1
o
40015:OUT3
: :
40017:OUT7)
40024-40031
(40024:OUT1
o
40025:OUT3
: :
40031:OUT15)
40014-40017 5
0
(40014:OUT1
o
40015:OUT3
: :
40017:OUT7)
40024-40031
(40024:OUT1
o
40025:OUT3
: :
40031:OUT15)
40014-40017 5
0
(40014:OUT1
o
40015:OUT3
: :
40017:OUT7)
40024-40031
(40024:OUT1
o
40025:OUT3
: :
40031:OUT15)
40014-40017 5
0
(40014:OUT1
o
40015:OUT3
: :
40017:OUT7)
40024-40031
(40024:OUT1
o
40025:OUT3
: :
40031:OUT15)

PrmNo
(Parameter
Number)
0

IndexNo
Category
(Index
Number)
0
OUTPUT OUTPUT
SPEAKER
CHANNEL CH STRIP PROCESSOR
1-8(16)
(1way/2way)

1

0

2

0

3

Parameter Name

MIN

Speaker
Limiter Threshold -54
Processor
2 Way
*Speaker
Processor
type (1 Way
or 2 Way) is
configurable
through
MTX Editor
software.
Attack 0.0

MAX
0

unit

Remarks

dB

120.0 ms

ms x 10
ex. 24.5ms x
10 = 245

Release 3.2m

42.600 s

* See "6.2.2.2.
GATE" / Decay
in "7. Parameter
Values"

0

On

ON

0:ON
1:OFF

4

0

Attack Fast
Mode

Manual -

* See "6.2.6.2.
SPEAKER
PROCESSOR"
in "7. Parameter
Values"

5

0

Release Fast
Mode

Manual -

* See "6.2.6.2.
SPEAKER
PROCESSOR"
in "7. Parameter
Values"

OFF

-

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

99

7. Parameter List
Model

Access ID
MemNo
ElmNo
Xpos
Ypos
MTX3 MTX5-D (Memory UniqueId (Element
(X Position) (Y Position)
Number)
Number)
512
40014-40017 6
0-1
0
(40014:OUT1
(0:LOW
o
40015:OUT3
1:HIGH)
: :
40017:OUT7)
40024-40031
(40024:OUT1
o
40025:OUT3
: :
40031:OUT15)
40014-40017 6
0
(40014:OUT1
o
40015:OUT3
: :
40017:OUT7)
40024-40031
(40024:OUT1
o
40025:OUT3
: :
40031:OUT15)
40014-40017 6
0
(40014:OUT1
o
40015:OUT3
: :
40017:OUT7)
40024-40031
(40024:OUT1
o
40025:OUT3
: :
40031:OUT15)
20021 0
0
0-7
o
(OUT1-8)
20028
0-15
o
(OUT1-16)
20022 0
0
0-15
o
(1-16ch)
20029
o
20023 0

o

20030
o
20023

o

20030
o
50010 0
o

o

o

o
1

o

o

0-7
0
(OUTPUT1-8)
0-39
(0- 7:OUTPUT1-8
8-23:DANTE1-16
24-39:SLOT1-16)
0-7
(OUTPUT1-8)
0-39
(0- 7:OUTPUT1-8
8-23:DANTE1-16
24-39:SLOT1-16)
0
0

0-15
(YDIF OUT
1-16)
0-31
(0-15:YDIF
OUT 1-16
16-32:Dante
OUT 1-16)

PrmNo
(Parameter
Number)
0

IndexNo
Category
(Index
Number)
0
OUTPUT OUTPUT
SPEAKER
CHANNEL CH STRIP PROCESSOR
1-8(16)
(1way/2way)

1

0

2

0

0

0

0

0

0

0

Parameter Name
Speaker
Out
Processor
2 Way
*Speaker
Processor
type (1 Way
or 2 Way) is
configurable
through
MTX Editor
software.

OUTPUT PORT

0

I/O

MAX

unit

Level

-∞

Mute

UNMUTED MUTED -

PEQOn OFF

10.00 dB

ON

-

Remarks
dB x 100
ex.-73.60dB x
100 = -7360
"setr" command
is available for
this parameter

0:UNMUTED
1:MUTED

0:ON
1:OFF

OUTPUT OutputPatch In
PATCH 8(16) Input
x 8(40)
Output

Patch NONE OUTPUT CH8
(SLOT
OUT 16)

* See "6.2.7.1.
OUTPUT PATCH"
in "6. Parameter
Values"

YDIF
Router
In
OUT
46(70)
PATCH Input x 16
Output
OUTPUT OutputPort Out
PORT
8(40)
Channel

Patch NONE OUTPUT CH8
(OUTPUT
CH16)
Polarity NORMAL INVERTED -

* See "6.2.7.2.
YDIF PATCH"
in "6. Parameter
Values"
0:NORMAL
1:INVERTED

Gain

1

0

MIN

PILOT
TONE

PilotTone
16(48)ch

Oscillator Level

-96.0

24.0

dB

dB x 10
ex. -14.5dB x
10 = -145

-∞

0.0

dB

dB x 100
ex.-73.60dB x
100 = -7360
"setr" command
is available for
this parameter
0:OFF
1:ON
0:OFF
1:ON

1

On

OFF

ON

-

0

ChSum On

OFF

ON

-

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

100

7. Parameter List

7.2. MRX7-D
Parameter Name
Ch

ANALOG IN

ANALOG OUT

Gain
+48V

-6
OFF

66
ON

unit
dB
-

Polarity

NORMAL

INVERTED

-

Gain

-96.0

24.0

dB

Polarity

NORMAL

INVERTED

-

Gain

-96.0

24.0

dB

Polarity

NORMAL

INVERTED

-

Gain

-96.0

24.0

dB

AEC

ON

OFF

ON

-

NR

ON

OFF

ON

-

Ambient

Threshold
Threshold

-72
-∞

-25
0.00

dB
dB

Gap

Threshold

-∞

0.00

dB

Time

0.1

5.0

s

MaxGain

0.0

18.0

dB

MinGain

-18.0

0.0

dB

Ratio*
0.5:1
ResponseTime 1
ON
OFF

2.0:1
60
ON

s
-

ResponseTime* 100m
Level
1
NoiseGateOn OFF

5.0
5
ON

s
-

On

ON

OFF

ON

-

BGM

Source*

BGM1

BGM4

-

ON

OFF

ON

-

Level

-∞

10.00

dB

ON

OFF

ON

-

Level

-∞

10.00

dB

ON

OFF

ON

-

Level

-∞

10.00

dB

ON

OFF

ON

-

Level

-∞

10.00

dB

ON

OFF

ON

-

Ch

SLOT OUT

Ch

DANTE OUT

Ch

Acoustic Echo Canceller

Ambient Noise Compensator

Program

On
Auto Gain Control

Combiner

Compensator

Room Combiner

Paging

RoomIn

RoomOut

Combine

MIN

MAX

Remarks
0:OFF
1:ON
0:NORMAL
1:INVERTED
dB x 10
e.g. -14.5dB x 10 = -145
0:NORMAL
1:INVERTED
dB x 10
e.g. -14.5dB x 10 = -145
0:NORMAL
1:INVERTED
dB x 10
e.g. -14.5dB x 10 = -145
0:OFF
1:ON
0:OFF
1:ON
dB x 100
e.g. -73.60dB x 100 = -7360
dB x 100
e.g. -73.60dB x 100 = -7360
sec x 10
e.g. 3.8sec x 10 = 38
dB x 10
e.g. 5.2dB x 10 = 52
dB x 10
e.g. -14.5dB x 10 = -145
* See "6.2.4.3. ANC" in "6. Parameter Values"
0:OFF
1:ON
* See "6.2.2.4. AGC" in "6. Parameter Values"
0:OFF
1:ON
0:OFF
1:ON
* See "6.3.3.1. Room Combiner" in "6.
Parameter Values"
0:OFF
1:ON
dB x 100
e.g. -73.60dB x 100 = -7360
"setr" command is available for this parameter
0:OFF
1:ON
dB x 100
e.g. -73.60dB x 100 = -7360
"setr" command is available for this parameter
0:OFF
1:ON
dB x 100
e.g. -73.60dB x 100 = -7360
"setr" command is available for this parameter
0:OFF
1:ON
dB x 100
e.g. -73.60dB x 100 = -7360
"setr" command is available for this parameter
0:OFF
1:ON

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

101

7. Parameter List
Combiner

Parameter Name
Room Combiner plus Master
Automixer

MAX

unit

OFF

ON

-

Mute

OFF

ON

-

ON

OFF

ON

-

Level

-∞

10.00

dB

Source*

BGM1

BGM4

-

ON

OFF

ON

-

Level

-∞

10.00

dB

ON

OFF

ON

-

Level

-∞

10.00

dB

ON

OFF

ON

-

Level

-∞

10.00

dB

ON

OFF

ON

-

Level

-∞

10.00

dB

Combine

ON

OFF

ON

-

MicCh

Mode*

Mute

Auto

-

Weight

-100.0

15.0

-

Override

OFF

ON

-

Override

OFF

ON

-

Mute

OFF

ON

-

OFF

ON

-

DelayTime

0.00

50.00

ms

ON

OFF

ON

-

DelayTime

0.00

250.00

ms

ON

OFF

ON

-

DelayTime

0.00

500.00

ms

ON

OFF

ON

-

DelayTime

0.00

1000.00

ms

MicsIn

BGM

Paging

RoomIn

RoomOut

Master

Delay

MIN
Override

Delay 50mSec ON

Delay
250mSec

Delay
500mSec

Delay
1000mSec

Remarks
0:OFF
1:ON
0:OFF
1:ON
0:OFF
1:ON
dB x 100
e.g. -73.60dB x 100 = -7360
"setr" command is available for this parameter
* See "6.3.3.1. Room Combine" in "6.
Parameter Values"
0:OFF
1:ON
dB x 100
e.g. -73.60dB x 100 = -7360
"setr" command is available for this parameter
0:OFF
1:ON
dB x 100
e.g. -73.60dB x 100 = -7360
"setr" command is available for this parameter
0:OFF
1:ON
dB x 100
e.g. -73.60dB x 100 = -7360
"setr" command is available for this parameter
0:OFF
1:ON
dB x 100
e.g. -73.60dB x 100 = -7360
"setr" command is available for this parameter
0:OFF
1:ON
* See "6.2.2.5. DUGAN AUTOMIXER" in "6.
Parameter Values"
* See "6.2.2.5. DUGAN AUTOMIXER" in "6.
Parameter Values"
0:OFF
1:ON
0:OFF
1:ON
0:OFF
1:ON
0:OFF
1:ON
ms x 100
e.g. 22.00ms x 100 = 2200
0:OFF
1:ON
ms x 100
e.g. 102.80ms x 100 = 10280
0:OFF
1:ON
ms x 100
e.g. 102.80ms x 100 = 10280
0:OFF
1:ON
ms x 100
e.g. 102.80ms x 100 = 10280

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

102

7. Parameter List
Dynamics

Parameter Name
Compressor
Dyn

Ducking

Gate

Limiter

Paging Ducker

Effect

Threshold
Ratio*

-54
1.0:1

0
∞:1

unit
dB
-

Knee*

HARD

5

-

Attack
Release*

0
3m

120
42.7

ms
s

Gain

0.0

18.0

dB

KeyIn

KeyIn*

SELF

KEYIN

-

On

ON

OFF

ON

-

Dyn

Threshold
Range
Attack
Release*

-54
-70
0
3m

0
0
240
42.7

dB
s

Hold*

0.02m

1.96

s

KeyIn

KeyIn*

SELF

KEYIN

-

On

ON

OFF

ON

-

Dyn

Threshold
Range
Attack
Decay*

-72
-70
0
3m

0
0
120
42.7

dB
s

Hold*

0.02m

1.96

s

KeyIn

KeyIn*

SELF

KEYIN

-

On

ON

OFF

ON

-

Dyn

Threshold
Attack

-54
0.0

0
120.0

dB
ms

Release*

3m

42.7

s

KeyIn

KeyIn*

SELF

KEYIN

-

On

ON

OFF

ON

-

Dyn

Range*

-∞

0.0

dB

Attack

0.0

10.0

s

Release

0.0

10.0

s

Hold

0.0

10.0

s

Trigger

OFF

ON

-

On

On

OFF

ON

-

Status

Range
Indicator
Type*

OFF

ON

-

Revaerb Hall

Vocal Echo

-

On

OFF

ON

-

RevHallTime*

0.3

10.0

s

RevStageTime* 0.3

10.0

s

KaraokeTime*
VocalTime*

1000.0
1000.0

ms
ms

Effect

SimpleEffect

MIN

0.4
0.4

MAX

Remarks
* See "6.2.2.3. COMPRESSOR" in "6.
Parameter Values"
* See "6.2.2.3. COMPRESSOR" in "6.
Parameter Values"
* See "6.2.2.2. GATE" / Decay in "6.
Parameter Values"
dB x 10
e.g. 5.2dB x 10 = 52
* See "6.3.4.1. Compressor" in "6. Parameter
Values"
0:OFF
1:ON

* See "6.2.2.2. GATE" / Decay in "6.
Parameter Values"
* See "6.2.2.2. GATE" in "6. Parameter
Values"
* See "6.3.4.1. Compressor" in "6. Parameter
Values"
0:OFF
1:ON

* See "6.2.2.2. GATE" in "6. Parameter
Values"
* See "6.2.2.2. GATE" in "6. Parameter
Values"
* See "6.3.4.1. Compressor" in "6. Parameter
Values"
0:OFF
1:ON
ms x 10
e.g. 24.5ms x 10 = 245
* See "6.2.2.2. GATE" / Decay in "6.
Parameter Values"
* See "6.3.4.1. Compressor" in "6. Parameter
Values"
0:OFF
1:ON
* See "6.2.4.1. PAGING" in "6. Parameter
Values"
s x 10
e.g. 5.3s x 10 = 53
s x 10
e.g. 5.3s x 10 = 53
s x 10
e.g. 5.3s x 10 = 53
0:OFF
1:ON
0:OFF
1:ON
0:OFF
1:ON
* See "6.2.3. EFFECT" in "6. Parameter
Values"
0:OFF
1:ON
* See "6.2.3. EFFECT" in "6. Parameter
Values"
* See "6.2.3. EFFECT" in "6. Parameter
Values"
* See "6.3.5. Effect" in "6. Parameter Values"
* See "6.3.5. Effect" in "6. Parameter Values"

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

103

7. Parameter List
EQ

GEQ

Parameter Name
Property

Limit

±15

-24

unit
dB

GEQOn

OFF

ON

-

Frequency

20.0

20.0k

Hz

Bypass

OFF

ON

-

Frequency

20.0

20.0k

Hz

Bypass

OFF

ON

-

Frequency

20.0

20.0k

Hz

Bypass

OFF

ON

-

GEQ

Q*
Gain
Bypass

63.0
-24.0
OFF

0.1
15.0
ON

dB
-

PEQ

Q*

63.0

0.1

-

Frequency

20.0*

20.0k

Hz

Gain*
Bypass

-18.0
OFF

18.0
ON

dB
-

Type

PEQ

LPF

-

Property

PEQOn

OFF

ON

-

Fader

Level

-∞

10.00

dB

ON

OFF

ON

-

Polarity

OFF

ON

-

Dynamic

AutoDetect

OFF

ON

-

FixedOn

ON

OFF

ON

-

Suppressor

Mode
Suppression
On

Speech
0
OFF

Music
9
ON

-

Frequency

20.0

20.0k

Hz

FilterType(*)

Thru

-

Gc*
ON

-6
OFF

48dB/Oct
Linkwitz
6
ON

Frequency

20.0

20.0k

Hz

FilterType*

Thru

-

Gc*
ON

-6
OFF

48dB/Oct
Linkwitz
6
ON

Frequency

20.0

20.0k

Hz

FilterType*

Thru

-

Gc*
Bypass

-6
OFF

48dB/Oct
Linkwitz
6
ON

Frequency

20.0

20.0k

Hz

FilterType*

Thru

-

Gc*
Bypass

-6
OFF

48dB/Oct
Linkwitz
6
ON

ON

OFF

ON

-

HPF

LPF

Notch

PEQ

Fader

Feedback
Suppressor

Notch FBS

Pitch Shift FBS

On
Filter

LPF

HPF

BPF

LPF

HPF

On

MIN

MAX

dB
-

dB
-

dB
-

dB
-

Remarks
0:±15
1:±12
2:±6
3:-24
0:OFF
1:ON
Hz x 1000
e.g. 1000Hz x 1000 = 1000000
0:OFF
1:ON
Hz x 1000
e.g. 1000Hz x 1000 = 1000000
0:OFF
1:ON
Hz x 1000
e.g. 1000Hz x 1000 = 1000000
0:OFF
1:ON
* See "6.3.6.1. GEQ" in "6. Parameter Values"
Value range varies with Limit
0:OFF
1:ON
* Available when PEQ type chosen
* See "6.2.2.1. 3BAND EQ" in "6. Parameter
Values"
Hz x 1000
e.g. 1000Hz x 1000 = 1000000
*100 : Other than Band A / B
* Not available when HPF/LPF type chosen
0:OFF
1:ON
* See "6.2.2.1. 3BAND EQ" in "6. Parameter
Values"
0:OFF
1:ON
dB x 100
e.g. -73.60dB x 100 = -7360
"setr" command is available for this parameter
0:OFF
1:ON
0:OFF
1:ON
0:OFF
1:ON
0:OFF
1:ON

0:OFF
1:ON
Hz x 1000
e.g. 1000Hz x 1000 = 1000000
* See "6.2.6.2. SPEAKER PROCESSOR" in
"6. Parameter Values"
*Available only when filter type is AdjustGc
0:OFF
1:ON
Hz x 1000
e.g. 1000Hz x 1000 = 1000000
* See "6.2.6.2. SPEAKER PROCESSOR" in
"6. Parameter Values"
*Available only when filter type is AdjustGc
0:OFF
1:ON
Hz x 1000
e.g. 1000Hz x 1000 = 1000000
* See "6.2.6.2. SPEAKER PROCESSOR" in
"6. Parameter Values"
*Available only when filter type is AdjustGc
0:OFF
1:ON
Hz x 1000
e.g. 1000Hz x 1000 = 1000000
* See "6.2.6.2. SPEAKER PROCESSOR" in
"6. Parameter Values"
*Available only when filter type is AdjustGc
0:OFF
1:ON
0:OFF
1:ON

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

104

7. Parameter List
Mixer

Parameter Name
Dugan Automixer
Master

Ch

Delay Matrix

Ch

MIN

MAX

unit

Override

OFF

ON

-

Mute

OFF

ON

-

Mode*

Mute

Auto

-

Weight*

-100.0

15.0

dB

Group*

a

Override

OFF

b (2 - 4 Channel) d (5 - 8 Channel)
h (9 - 16 Channel)
ON
-

Level

-∞

0.00

dB

On

OFF

ON

-

DelayTime

0.00

250.00

ms

500.00
Matrix Mixer

Oscillator Mono

Paging

Ch

Oscillator

On
Gain

ZoneGroup
Polarity

Level

-∞

0.00

dB

ON

OFF

ON

-

Level

-∞

0.0

dB

ON

OFF

ON

-

VariFrequency 20.0

20.0k

Hz

Waveform*

SINE 100Hz

VARI

-

On
Range

OFF
-∞

ON
0.0

dB

Attack

0.0

10.0

s

Release

0.0

10.0

s

ZoneOn
Polarity

OFF
NORMAL

ON
INVERTED

-

Revolabs control

Ch

ON

OFF

ON

Router

in

Patch

NONE

Source Selector

Position

Position

1

Speech Privacy

Source

SelectType*

Forest

2(2 Input)
4(4 Input)
8(8 Input)
16(16 Input)
24(24 Input)
32(32 Input)
64(64 Input)
4(4 position)
8(8 position)
16(16 position)
Building
-

ON

OFF

ON

-

Level

-∞

0.0

dB

MixRatio

10

70

-

Remarks
0:OFF
1:ON
0:OFF
1:ON
* See "6.2.2.5. DUGAN AUTOMIXER" in "6.
Parameter Values"
* See "6.2.2.5. DUGAN AUTOMIXER" in "6.
Parameter Values"
* See "6.3.8.1. Dugan Automixer" in "6.
Parameter Values"
0:OFF
1:ON
dB x 100
e.g. -73.60dB x 100 = -7360
"setr" command is available for this parameter
0:OFF
1:ON
ms x 100
e.g. 102.80ms x 100 = 10280
ms x 100
e.g. 102.80ms x 100 = 10280
dB x 100
e.g. -73.60dB x 100 = -7360
"setr" command is available for this parameter
0:OFF
1:ON
dB x 100
e.g. -73.60dB x 100 = -7360
"setr" command is available for this parameter
0:OFF
1:ON
Hz x 1000
e.g. 1000Hz x 1000 = 1000000
* See "6.2.5.2. OSCILLATOR" in "6.
Parameter Values"
* See "19. Paging Ducker" in "6. Parameter
Values"
s x 10
ex. 5.3s x 10 = 53
s x 10
ex. 5.3s x 10 = 53
0:NORMAL
1:INVERTED
0:OFF
1:ON

* See "6.3.11. Speech Privacy" in "6.
Parameter Values"
0:OFF
1:ON
dB x 100
ex. -73.60dB x 100 = -7360
"setr" command is available for this parameter

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

105

7. Parameter List
Speaker Processor

Parameter Name
In

Level

-∞

MAX
10.00

unit
dB

ON

OFF

ON

-

Delay

0.00

500.00

ms

LPFFrequency 20.0

20.0k

Hz

HPFFrequency 20.0

20.0k

Hz

LPFType

Thru

-

HPFType

Thru

LPFGc*
HPFGc*
Polarity

-6
-6
NORMAL

48dB/Oct
Linkwitz
48dB/Oct
Linkwitz
6
6
INVERTED

Center

Frequency

20.0

20.0k

Hz

PEQ

Q*

63.0

0.1

-

Frequency

20.0*

20.0k

Hz

Gain*

-18.0

18.0

dB

Bypass

OFF

ON

-

Type

PEQ

Horn EQ

-

Threshold
Attack

-54
0.0

0
120.0

dB
ms

Release

3m

42.7

s

ON

OFF

ON

-

AttackMode
ReleaseMode
Level

Fast
Fast
-∞

Manual
Manual
10.00

dB

Mute

UNMUTED

MUTED

-

PEQOn

ON*

OFF*

-

Delay

Band

Limiter

Out

MIN

dB
dB
-

Remarks
dB x 100
e.g. -73.60dB x 100 = -7360
"setr" command is available for this parameter
0:OFF
1:ON
ms x 100
e.g. 102.80ms x 100 = 10280
Hz x 1000
e.g. 1000Hz x 1000 = 1000000
Hz x 1000
e.g. 1000Hz x 1000 = 1000000
* See "6.2.6.2. SPEAKER PROCESSOR" in
"6. Parameter Values"
* See "6.2.6.2. SPEAKER PROCESSOR" in
"6. Parameter Values"
*Available only when filter type is AdjustGc
*Available only when filter type is AdjustGc
0:NORMAL
1:INVERTED
Hz x 1000
e.g. 1000Hz x 1000 = 1000000
* Available only when PEQ is APF 2nd
* See "6.2.2.1. 3BAND EQ" in "6. Parameter
Values"
*500 : When HORN EQ is chosen
100 : Other than Band A / B
Hz x 1000
e.g. 1000Hz x 1000 = 1000000
* Not available for HPF/LPF/APF or PEQ is
APF 2nd
dB x 10
e.g. -14.5dB x 10 = -145
0:OFF
1:ON
* See "6.2.6.2. SPEAKER PROCESSOR" in
"6. Parameter Values"
ms x 10
e.g. 24.5ms x 10 = 245
* See "6.2.2.2. GATE" / Decay in "6.
Parameter Values"
0:OFF
1:ON

dB x 100
e.g. -73.60dB x 100 = -7360
"setr" command is available for this parameter
0:UNMUTED
1:MUTED
*0:ON
1:OFF

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

106

7. Parameter List

7.3. XMV Series
Model

4ch
o
o
o
o
o

Access ID
MemNo
ElmNo
Xpos
Ypos
8ch 4ch D 8ch D (Memory UniqueId (Element
(X Position) (Y Position)
Number)
Number)
o
512
1
4
0 to 3
0
o
o
0 to 7
o
0 to 3
0
o
o
0 to 7
o
0 to 3
0
o
o
0 to 7
o
0 to 3
0
o
o
0 to 7
6
0
0
o
o
o

o

o

o

o

o

o

o

o

o

o
o

2

o
o

IndexNo
(Index
Number)
0

1

Parameter Name

MIN

Remarks

0

dB

Synchronized
with DigitalATT

0

Digital
ATT *2

-99

0

dB

Synchronized
with ATT

2

0

Mute

OFF

ON

-

0:OFF
1:ON

3

0

Polarity

Normal

Inverse

-

0:Normal
1:Inverse

0

0

Power

Standby Standby ON

-

InputSelect Analog
*1 *3

0:ON
1:Standby
Switching input
source of all
channel.
0:Analog
1:Digital
2.Multiple
0: -20dBFS
1: -3dBFS
Switching input
source of by
channel.
0:Analog
1:Digital

0

0

0

Utility

10

0

0

0

0

11

0 to 3

0

0

0

DigitalInput Type
0dB
Sensitivity
ChUtility Input
Analog
Select *3

0 to 7

0

0

0

0 to 3

0

0

0

0 to 7

0

0

0

o

unit

-99

0

0

MAX

Signal
ATT *2
Processing

7

o

o

PrmNo
(Parameter
Number)
0

Channel Channel
Name
Name 4
Channel
Channel
Name 8
Channel

ChName Name

Multiple -

+17dB

-

Digital

-

Character (UTF-8) 48byte

Notification only

*1 : Note
The XMV’s input sensitivity is -3dBFS (rated output at -3dBFS) when connected via digital (YDIF or Dante) and +4dBu (rated output
at +4dBu) when connected via analog.
Please set an appropriate level before switching input.
*2 : The ATT and DigitalATT parameters are always synchronized internally within an XMV amplifier.
Controlling either one will provide the same result.
*3 : When "Utility/InputSelect" is changed to "Analog (or Digital)", "ChUtility/InputSelect" for all channels will be forcibly changed to
Analog (or Digital).
When "ChUtility/InputSelect" for all channels are set as "Analog (or Digital)" and a channel is changed to “Digital (or Analog)”,
"Utility/InputSelect" will be forcibly changed to "Multiple".
< XMV Block Diagram > e.g. XMV4280/XMV4140/XMV4280-D/XMV4140-D

+-G

CH A, B, C, D
(E, F, G, H for XMV8xxx)

ATT

HA

AD
INPUT
SOURCE
SELECT

ATT
YDIF model only
YDIF
In

Out
INPUT
REDUNDANCY

-3dBFS
Dante model only
Dante

-20dBFS
DIGITAL INPUT
SENSITIVITY

ATT

DigitalATT

PRIMARY
Dante
Redundancy
SECONDARY

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

107

7. Parameter List

7.4. EXi8
Access ID
MemNo
ElmNo
PrmNo IndexNo
Xpos
Ypos
(Memory UniqueId (Element
(Parameter (Index
(X Position) (Y Position)
Number)
Number)
Number) Number)
512
1
3
0 to 7
0
0
0
1

Parameter Name

MIN

Signal
GAIN
Processing +48V

MAX

unit

-6
OFF

66
ON

dB
-

2

Phase

OFF

ON

-

3

On

OFF

ON

-

4

HPFOn

OFF

ON

-

5

HPFFrequency 20

20000

Hz

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

Remarks

0:OFF
1:ON
0:OFF
1:ON
0:OFF
1:ON
0:OFF
1:ON
Hz x 1000
ex. 1000Hz x
1000000

108

7. Parameter List

7.5. EXo8
Access ID
MemNo
ElmNo
PrmNo IndexNo
Xpos
Ypos
(Memory UniqueId (Element
(Parameter (Index
(X Position) (Y Position)
Number)
Number)
Number) Number)
512
1
3
0 to 7
0
0
0
1
2

Parameter Name
Signal
Polarity
Processing
On
Gain

MIN

MAX

unit

Normal

Inverse

-

OFF

ON

-

-96

24

dB

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

Remarks
0:Normal
1:Inverse
0:OFF
1:ON
dB x 10
ex. -14.5dB x
10 = -145

109

7. Parameter List

7.6. MY4-AEC
7.6.1. MTX3, MTX5-D
Access ID
MemNo
ElmNo
PrmNo IndexNo
Parameter Name
Xpos
Ypos
(Memory UniqueId (Element
(Parameter (Index
(X Position) (Y Position)
Number)
Number)
Number) Number)
512
20034
0
0
1
0
0
MY4MY4AEC
NearEndMic Patch
AEC
InputPatch
INPUT
PATCH

90000

OUTPUT CH16

On

OFF

ON

-

Effect
PttOn

1
OFF

4
ON

-

PttThreshold -80
MicType Fixed

-20
Moving

dB
-

Distance
On

2
OFF

40
ON

1

Width

1/10

1/93

2

Depth

-6

-18

On

OFF

ON

FarEndNR On

OFF

ON

meter
0:OFF
1:ON
oct
* See "6.2.8.2.
MY4-AEC FBS"
in "6. Parameter
Values"
dB
* See "6.2.8.2.
MY4-AEC FBS"
in "6. Parameter
Values"
0:OFF
1:ON
0:OFF
1:ON

Reference On

OFF

ON

1

0

0-3
(AEC1-4)

0

0

FromFarEnd

0

MY4AEC

1
2

Acoustic
AEC
Echo
Canceller 4
Channel

3
4

2
3

4

0-3
(AEC1-4)
0

0-3
(AEC1-4)

0

Remarks

NONE

1

0

unit

OUTPUT CH16

0

0-3
(AEC1-4)

MAX

NONE

1

1

MIN

5
0

FBS

0

MicNR

0-3
0
(0:Far-end A
1:Far-end B
2:Far-end C
3:Far-end D)
0-3
0
(0:Far-end A
1:Far-end B
2:Far-end C
3:Far-end D)

-

* See "12.
MY4-AEC
Input Patch" in
"6. Parameter
Values"
* See "12.
MY4-AEC
Input Patch" in
"6. Parameter
Values"
0:OFF
1:ON
0:OFF
1:ON
0:Fixed
1:Moving

0:OFF
1:ON

7.6.2. MRX7-D
AEC

Parameter Name
AEC

FBS

MicNR
FarEndNR
Reference
(FarEndMix)

On
Effect
PttOn
PttThreshold
MicType

OFF
1
OFF
-80
Fixed

MIN

MAX
ON
4
ON
-20
Moving

unit
dB
-

Remarks

Distance
On
Width

2
OFF
1/10

40
ON
1/93

Depth

-6

-18

On
On
On

OFF
OFF
OFF

ON
ON
ON

meter
oct
* See "6.2.8.2. MY4-AEC FBS" in "6.
Parameter Values"
dB
* See "6.2.8.2. MY4-AEC FBS" in "6.
Parameter Values"
-

0:Fixed
1:Moving

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

110

8. Meter List
8.1. MTX3/MTX5-D
Model
MTX3
o

Access ID
MemNo
Category
MTX5-D (Memory UniqueId
Number)
512
20000
INPUT PORT
o

o
o
o

20024
20001
20002
20003

o
o
o

o
o

INPUT(SLOT)
INPUT CHANNEL

EQ OUT

20009
20010
GATE

40000
40001
40000

o

INPUT(ANALOG)
INPUT(YDIF)

40002

o

Meter Name

COMP

40001

o
o
o
o

40002
40003
40006
50011

Dugan AUTO MIXER

Meter 12 Channel
(INPUT1-8, STIN1L-STIN2R)
Meter 16 Channel
(YDIF IN 1-16)

level

Meter 16 Channel
(SLOT IN 1-16)
Meter 22 Channel
(CH1-8, STIN1L-STIN3R, CH9-16)
Meter 8 Channel
(CH1-8)
Meter 22 Channel
(CH9-16, STIN1L-STIN3R, CH17-24)
Gate 8 Channel
(CH1-8)
Gate 8 Channel
(CH1-8)
Gate 8 Channel
(CH9-16)
Compressor 8 Channel
(CH1-8)
Compressor 4 Channel
(STIN1L-STIN2R)
Compressor 8 Channel
(CH1-8)
Compressor 8 Channel
(CH9-16)
Compressor 4 Channel
(STIN1L-STIN2R)
Auto Mixer 4 Channel
(CH1-4)

level

o

Auto Mixer 8 Channel
(CH1-8)
o

20005

o
o
o

POST ON

20011
20012
20009

o
o

20015
20012

o
o

o

o

o

1st PRIORITY PRIORITY
DUCKER

ANC AMBIENT SOURCE

20021
20015

o

2nd PRIORITY PRIORITY
DUCKER

20020
20014

o

ZONE

20019
20013

o

EFFECT RETURN

20022

ZONE OUT

Type (*)

Meter 22 Channel
(CH1-8, STIN1L-STIN3R, CH9-16)
Meter 8 Channel
(CH1-8)
Meter 22 Channel
(CH9-16, STIN1L-STIN3R, CH17-24)
Meter 4 Channel
(Fx RTN1 L-Fx RTN2 R)
Meter 4 Channel
(Fx RTN1 L-Fx RTN2 R)
Ducking 8 Channel
(ZONE1-8)
Ducking 8 Channel
(ZONE1-8)
Ducking 8 Channel
(ZONE1-8)
Ducking 8 Channel
(ZONE1-8)
Ambient Noise Compensator 8
Channel
ZONE 1-8(AMBIENT SOURCE)
Ambient Noise Compensator 8
Channel
ZONE 1-8(AMBIENT SOURCE)
Meter 8 Channel
ZONE 1-8
Meter 16 Channel
ZONE 1-16

level

Remarks
* Type is for "1-7)
Parameter change
notification" command
option2.

level
level
level
gr
gr
gr
gr
gr
gr
gr
gr
level
(See the
spread sheet
"Dugan
Automixer 2
- 4 Channel"
in MRX7-D
Meter List)
level
(See the
spread sheet
"Dugan
Automixer 5
- 8 Channel"
in MRX7-D
Meter List)
level
level
level
level
level
gr
gr
gr
gr
level
level
level
level

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

111

8. Meter List
Model
MTX3
o
o
o
o
o
o
o
o

Access ID
MemNo
Category
Meter Name
MTX5-D (Memory UniqueId
Number)
512
40006
OUTPUT CHANNEL OUTPUT CHANNEL(1way) Speaker Processor
SPEAKER PROCESSOR
(OUTPUT CH1)
LIMITER
40007
Speaker Processor
(OUTPUT CH2)
40008
Speaker Processor
(OUTPUT CH3)
40009
Speaker Processor
(OUTPUT CH4)
40010
Speaker Processor
(OUTPUT CH5)
40011
Speaker Processor
(OUTPUT CH6)
40012
Speaker Processor
(OUTPUT CH7)
40013
Speaker Processor
(OUTPUT CH8)
40008
Speaker Processor
o
(OUTPUT CH1)
40009
Speaker Processor
o
(OUTPUT CH2)
40010
Speaker Processor
o
(OUTPUT CH3)
40011
Speaker Processor
o
(OUTPUT CH4)
40012
Speaker Processor
o
(OUTPUT CH5)
40013
Speaker Processor
o
(OUTPUT CH6)
40014
Speaker Processor
o
(OUTPUT CH7)
40015
Speaker Processor
o
(OUTPUT CH8)
40016
Speaker Processor
o
(OUTPUT CH9)
40017
Speaker Processor
o
(OUTPUT CH10)
40018
Speaker Processor
o
(OUTPUT CH11)
40019
Speaker Processor
o
(OUTPUT CH12)
40020
Speaker Processor
o
(OUTPUT CH13)
40021
Speaker Processor
o
(OUTPUT CH14)
40022
Speaker Processor
o
(OUTPUT CH15)
40023
Speaker Processor
o
(OUTPUT CH16)

Type (*)
1 Way

gr

1 Way

gr

1 Way

gr

1 Way

gr

1 Way

gr

1 Way

gr

1 Way

gr

1 Way

gr

1 Way

gr

1 Way

gr

1 Way

gr

1 Way

gr

1 Way

gr

1 Way

gr

1 Way

gr

1 Way

gr

1 Way

gr

1 Way

gr

1 Way

gr

1 Way

gr

1 Way

gr

1 Way

gr

1 Way

gr

1 Way

gr

Remarks
* Type is for "1-7)
Parameter change
notification" command
option2.

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

112

8. Meter List
Model
MTX3
o
o
o
o
o
o
o
o

o

o

Access ID
MemNo
Category
Meter Name
MTX5-D (Memory UniqueId
Number)
512
40006
OUTPUT CHANNEL OUTPUT CHANNEL(2way) Speaker Processor 2 Way
SPEAKER PROCESSOR
(OUTPUT CH1 (Low))
LIMITER
40007
Speaker Processor 2 Way
(OUTPUT CH1 (High))
40008
Speaker Processor 2 Way
(OUTPUT CH3 (Low))
40009
Speaker Processor 2 Way
(OUTPUT CH3 (High))
40010
Speaker Processor 2 Way
(OUTPUT CH5 (Low))
40011
Speaker Processor 2 Way
(OUTPUT CH5 (High))
40012
Speaker Processor 2 Way
(OUTPUT CH7 (Low))
40013
Speaker Processor 2 Way
(OUTPUT CH7 (High))
40008
Speaker Processor 2 Way
o
(OUTPUT CH1 (Low))
40009
Speaker Processor 2 Way
o
(OUTPUT CH1 (High))
40010
Speaker Processor 2 Way
o
(OUTPUT CH3 (Low))
40011
Speaker Processor 2 Way
o
(OUTPUT CH3 (High))
40012
Speaker Processor 2 Way
o
(OUTPUT CH5 (Low))
40013
Speaker Processor 2 Way
o
(OUTPUT CH5 (High))
40014
Speaker Processor 2 Way
o
(OUTPUT CH7 (Low))
40015
Speaker Processor 2 Way
o
(OUTPUT CH7 (High))
40016
Speaker Processor 2 Way
o
(OUTPUT CH9 (Low))
40017
Speaker Processor 2 Way
o
(OUTPUT CH9 (High))
40018
Speaker Processor 2 Way
o
(OUTPUT CH11 (Low))
40019
Speaker Processor 2 Way
o
(OUTPUT CH11 (High))
40020
Speaker Processor 2 Way
o
(OUTPUT CH13 (Low))
40021
Speaker Processor 2 Way
o
(OUTPUT CH13 (High))
40022
Speaker Processor 2 Way
o
(OUTPUT CH15 (Low))
40023
Speaker Processor 2 Way
o
(OUTPUT CH15 (High))
20020
OUTPUT CHANNEL
Meter 8 Channel
(OUTPUT CH1-8)
20027
Meter 16 Channel
o
(OUTPUT CH1-16)
20025
OUTPUT PORT
OUTPUT (ANALOG)
Meter 8 Channel
(OUTPUT CH1-8)
20031
Meter 8 Channel
o
(OUTPUT CH1-8)
20032
OUTPUT (SLOT)
Meter 16 Channel
o
(SLOT OUT 1-16)
90000
MY4-AEC
MY4-AEC
(Mic In. 1-4
Ref In. 1-4
o
Echo Attn. 1-4
ERL 1-4
PTT Thesh. 1-4)

Type (*)
gr
gr

Remarks
* Type is for "1-7)
Parameter change
notification" command
option2.

gr
gr
gr
gr
gr
gr
gr
gr
gr
gr
gr
gr
gr
gr
gr
gr
gr
gr
gr
gr
gr
gr
level
level
level
level
level
level

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

113

8. Meter List

8.2. MRX7-D
Category
-

-

-

-

-

-

-

-

Meter Name
8 Channel
(INPUT1-8)
ANALOG OUT
8 Channel
(OUTPUT1-8)
YDIF IN
16 Channel
(YDIF IN 1-16)
SLOT IN
16 Channel
(SLOT IN 1-16)
SLOT OUT
16 Channel
(SLOT OUT 1-16)
STEREO IN
4 Channel
(INPUT 1L-INPUT 2R)
MY4-AEC
16 Channel
(MicIn.1-4
RefIn.1-4
EchoAttn.1-4
ERL.1-4)
Ambient Noise Compensator
Mono
(AMBIENT SOURCE, OUTPUT)
Stereo
(AMBIENT SOURCE, OUTPUT L, OUTPUT R)
Auto Gain Control
Mono
(INPUT,OUTPUT)
Stereo
(INPUT L-OUTPUT R)
Dynamics
Compressor / Ducking / Gate /
Mono
Limiter
(OUTPUT)
Stereo
(OUTPUT L, OUTPUT R)
Mono
(GR)
Stereo
(GR L, GR R)
Paging Ducker
Mono
(OUTPUT)
Stereo
(OUTPUT L, OUTPUT R)
EQ GEQ
Mono
(INPUT,OUTPUT)
Stereo
(INPUT L-OUTPUT R)
Fader
1 Channel
(CH1)
2 Channel
(CH1-2)
4 Channel
(CH1-4)
8 Channel
(CH1-8)
16 Channel
(CH1-16)
32 Channel
(CH1-32)
Meter
1 Channel
(CH1)
2 Channel
(CH1-2)
4 Channel
(CH1-4)
8 Channel
(CH1-8)
16 Channel
(CH1-16)
32 Channel
(CH1-32)
Delay Matrix
4 OUT
(OUTPUT1-4)
8 OUT
(OUTPUT1-8)
16 OUT
(OUTPUT1-16)

ANALOG IN

Type
level

Remarks

level
level
level
level
level
level

level

level

level

gr

level

level

level

level

level

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

114

8. Meter List
Category
-

Matrix Mixer

-

Oscillator

-

Speaker Processor

-

Room Combiner plus Auto Mixer
( Mic 1 - 16 Channel )
Room Combiner plus Auto Mixer
( Mic 17 - 24 Channel )
Dugan Automixer 2 - 4 Channel
Dugan Automixer 5 - 8 Channel
Dugan Automixer 9 - 16 Channel
Dugan Automixer 17 - 24 Channel

Meter Name
2 OUT
(OUTPUT1-2)
4 OUT
(OUTPUT1-4)
8 OUT
(OUTPUT1-8)
16 OUT
(OUTPUT1-16)
24 OUT
(OUTPUT1-24)
32 OUT
(OUTPUT1-32)
40 OUT
(OUTPUT1-40)
48 OUT
(OUTPUT1-48)
56 OUT
(OUTPUT1-56)
64 OUT
(OUTPUT1-64)
Meter 1 Channel
(OUTPUT)
1 Way
(INPUT
LIMITER OUT
OUTPUT)
2 Way
(INPUT
LIMITER OUT(HIGH)
LIMITER OUT(LOW)
OUTPUT(HIGH)
OUTPUT(LOW))
3 Way
(INPUT
LIMITER OUT(HIGH)
LIMITER OUT(MID)
LIMITER OUT(LOW)
OUTPUT(HIGH)
OUTPUT(MID)
OUTPUT(LOW))
4 Way
(INPUT
LIMITER OUT(HIGH)
LIMITER OUT(HIGH-MID)
LIMITER OUT(LOW-MID)
LIMITER OUT(LOW)
OUTPUT(HIGH)
OUTPUT(HIGH-MID)
OUTPUT(LOW-MID)
OUTPUT(LOW))
1 Way
(LIMITER GR)
2 Way
(LIMITER GR(HIGH)
LIMITER GR(LOW))
3 Way
(LIMITER GR(HIGH)
LIMITER GR(MID)
LIMITER GR(LOW))
4 Way
(LIMITER GR(HIGH)
LIMITER GR(HIGH-MID)
LIMITER GR(LOW-MID)
LIMITER GR(LOW))
*1

Type
level

Remarks

level
level

gr

*1

*2

*2

*3
*4
*5
*6

*3
*4
*5
*6

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

115

8. Meter List
*1 Room Combiner plus Auto Mixer
No.

Mic Input Channel
3
··
Level (*)
··
(Ch01)
Level (*)
··
(Ch02)
Level (*)
··
(Ch03)
:
··
··

2

1
Level (*)
(Ch01)
-

3

-

2
Level (*)
(Ch01)
Level (*)
(Ch02)
-

:
15

:
-

:
-

16

-

-

-

··

17

19

-

AutoMixGain
(Ch01)
AutoMixGain
(Ch02)
-

:
31

:
-

:
-

AutoMixGain
(Ch01)
AutoMixGain
(Ch02)
AutoMixGain
(Ch03)
:
-

··

18

AutoMixGain
(Ch01)
-

32

-

-

-

··

33

35

-

Input
(Ch01)
Input
(Ch02)
-

:
47

:
-

:
-

Input
(Ch01)
Input
(Ch02)
Input
(Ch03)
:
-

··

34

Input
(Ch01)
-

48

-

-

-

··

49

51

-

Output
(Ch01)
Output
(Ch02)
-

:
63

:
-

:
-

Output
(Ch01)
Output
(Ch02)
Output
(Ch03)
:
-

··

50

Output
(Ch01)
-

64

-

-

-

··

1

··
··
··
··

··
··
··
··

··
··
··
··

15
Level (*)
(Ch01)
Level (*)
(Ch02)
Level (*)
(Ch03)
:
Level (*)
(Ch15)
AutoMixGain
(Ch01)
AutoMixGain
(Ch02)
AutoMixGain
(Ch03)
:
AutoMixGain
(Ch15)
Input
(Ch01)
Input
(Ch02)
Input
(Ch03)
:
Input
(Ch15)
Output
(Ch01)
Output
(Ch02)
Output
(Ch03)
:
Output
(Ch15)
-

16
Level (*)
(Ch01)
Level (*)
(Ch02)
Level (*)
(Ch03)
:
Level (*)
(Ch15)
Level (*)
(Ch16)
AutoMixGain
(Ch01)
AutoMixGain
(Ch02)
AutoMixGain
(Ch03)
:
AutoMixGain
(Ch15)
AutoMixGain
(Ch16)
Input
(Ch01)
Input
(Ch02)
Input
(Ch03)
:
Input
(Ch15)
Input
(Ch16)
Output
(Ch01)
Output
(Ch02)
Output
(Ch03)
:
Output
(Ch15)
Output
(Ch16)

Type
level

- : 00 (unused data)
* : Input level which applied Weight parameter

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

116

8. Meter List
*2 Room Combiner plus Auto Mixer
No.

Mic Input Channel
19
··
Level (*)
··
(Ch01)
Level (*)
··
(Ch02)
:
··
Level (*)
··
(Ch17)
Level (*)
··
(Ch18)
Level (*)
··
(Ch19)
:
··
··

18

17
Level (*)
(Ch01)
Level (*)
(Ch02)
:
Level (*)
(Ch17)
-

19

-

18
Level (*)
(Ch01)
Level (*)
(Ch02)
:
Level (*)
(Ch17)
Level (*)
(Ch18)
-

:
23

:
-

:
-

24

-

-

-

··

25

43

-

AutoMIxGain
(Ch01)
AutoMIxGain
(Ch02)
:
AutoMIxGain
(Ch17)
AutoMIxGain
(Ch18)
-

:
47

:
-

:
-

AutoMIxGain
(Ch01)
AutoMIxGain
(Ch02)
:
AutoMIxGain
(Ch17)
AutoMIxGain
(Ch18)
AutoMIxGain
(Ch19)
:
-

··

42

AutoMIxGain
(Ch01)
AutoMIxGain
(Ch02)
:
AutoMIxGain
(Ch17)
-

48

-

-

-

··

49

67

-

Input
(Ch01)
Input
(Ch02)
:
Input
(Ch17)
Input
(Ch18)
-

:
71

:
-

:
-

Input
(Ch01)
Input
(Ch02)
:
Input
(Ch17)
Input
(Ch18)
Input
(Ch19)
:
-

··

66

Input
(Ch01)
Input
(Ch02)
:
Input
(Ch17)
-

72

-

-

-

··

73

91

-

Output
(Ch01)
Output
(Ch02)
:
Output
(Ch17)
Output
(Ch08)
-

:
95

:
-

:
-

Output
(Ch01)
Output
(Ch02)
:
Output
(Ch17)
Output
(Ch08)
Output
(Ch19)
:
-

··

90

Output
(Ch01)
Output
(Ch02)
:
Output
(Ch17)
-

96

-

-

-

··

1
2
:
17

26
:
41

50
:
65

74
:
89

··
··
··
··
··
··
··

··
··
··
··
··
··
··

··
··
··
··
··
··
··

23
Level (*)
(Ch01)
Level (*)
(Ch02)
:
Level (*)
(Ch17)
Level (*)
(Ch18)
Level (*)
(Ch19)
:
Level (*)
(Ch23)
AutoMIxGain
(Ch01)
AutoMIxGain
(Ch02)
:
AutoMIxGain
(Ch17)
AutoMIxGain
(Ch18)
AutoMIxGain
(Ch19)
:
AutoMIxGain
(Ch23)
Input
(Ch01)
Input
(Ch02)
:
Input
(Ch17)
Input
(Ch18)
Input
(Ch19)
:
Input
(Ch23)
Output
(Ch01)
Output
(Ch02)
:
Output
(Ch17)
Output
(Ch08)
Output
(Ch19)
:
Output
(Ch23)
-

24
Level (*)
(Ch01)
Level (*)
(Ch02)
:
Level (*)
(Ch17)
Level (*)
(Ch18)
Level (*)
(Ch19)
:
Level (*)
(Ch23)
Level (*)
(Ch24)
AutoMIxGain
(Ch01)
AutoMIxGain
(Ch02)
:
AutoMIxGain
(Ch17)
AutoMIxGain
(Ch18)
AutoMIxGain
(Ch19)
:
AutoMIxGain
(Ch23)
AutoMIxGain
(Ch24)
Input
(Ch01)
Input
(Ch02)
:
Input
(Ch17)
Input
(Ch18)
Input
(Ch19)
:
Input
(Ch23)
Input
(Ch24)
Output
(Ch01)
Output
(Ch02)
:
Output
(Ch17)
Output
(Ch08)
Output
(Ch19)
:
Output
(Ch23)
Output
(Ch24)

Type
level

- : 00 (unused data)
* : Input level which applied Weight parameter

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

117

8. Meter List
*3 Dugan Automixer 2 - 4 Channel
No.

3

2
Level (*)
(Ch01)
Level (*)
(Ch02)
-

4

-

5

7

AutoMixGain
(Ch01)
AutoMixGain
(Ch02)
-

8

-

9

11

Input
(Ch01)
Input
(Ch02)
-

12

-

13

15

Output
(Ch01)
Output
(Ch02)
-

16

-

1
2

6

10

14

Channel
3
Level (*)
(Ch01)
Level (*)
(Ch02)
Level (*)
(Ch03)
AutoMixGain
(Ch01)
AutoMixGain
(Ch02)
AutoMixGain
(Ch03)
Input
(Ch01)
Input
(Ch02)
Input
(Ch03)
Output
(Ch01)
Output
(Ch02)
Output
(Ch03)
-

4
Level (*)
(Ch01)
Level (*)
(Ch02)
Level (*)
(Ch03)
Level (*)
(Ch04)
AutoMixGain
(Ch01)
AutoMixGain
(Ch02)
AutoMixGain
(Ch03)
AutoMixGain
(Ch04)
Input
(Ch01)
Input
(Ch02)
Input
(Ch03)
Input
(Ch04)
Output
(Ch01)
Output
(Ch02)
Output
(Ch03)
Output
(Ch04)

Type
level

- : 00 (unused data)
* : Input level which applied Weight parameter

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

118

8. Meter List
*4 Dugan Automixer 5 - 8 Channel
No.

Channel
6
7
Level (*)
Level (*)
(Ch01)
(Ch01)
Level (*)
Level (*)
(Ch02)
(Ch02)
:
:
Level (*)
Level (*)
(Ch05)
(Ch05)
Level (*)
Level (*)
(Ch06)
(Ch06)
Level (*)
(Ch07)
-

6

5
Level (*)
(Ch01)
Level (*)
(Ch02)
:
-Level (*)
(Ch05)
-

7

-

8

-

9

14

AutoMixGain
(Ch01)
AutoMixGain
(Ch02)
:
AutoMixGain
(Ch05)
-

15

-

AutoMixGain
(Ch01)
AutoMixGain
(Ch02)
:
AutoMixGain
(Ch05)
AutoMixGain
(Ch06)
-

16

-

-

17

22

Input
(Ch01)
Input
(Ch02)
:
Input
(Ch05)
-

23

-

Input
(Ch01)
Input
(Ch02)
:
Input
(Ch05)
Input
(Ch06)
-

24

-

-

25

31

Output
(Ch01)
Output
(Ch02)
:
Output
(Ch05)
-

31

-

Output
(Ch01)
Output
(Ch02)
:
Output
(Ch05)
Output
(Ch06)
-

32

-

-

1
2
:
5

10
:
13

18
:
21

26
:
27

AutoMixGain
(Ch01)
AutoMixGain
(Ch02)
:
AutoMixGain
(Ch05)
AutoMixGain
(Ch06)
AutoMixGain
(Ch07)
Input
(Ch01)
Input
(Ch02)
:
Input
(Ch05)
Input
(Ch06)
Input
(Ch07)
Output
(Ch01)
Output
(Ch02)
:
Output
(Ch05)
Output
(Ch06)
Output
(Ch07)
-

8
Level (*)
(Ch01)
Level (*)
(Ch02)
:
Level (*)
(Ch05)
Level (*)
(Ch06)
Level (*)
(Ch07)
Level (*)
(Ch08)
AutoMixGain
(Ch01)
AutoMixGain
(Ch02)
:
AutoMixGain
(Ch05)
AutoMixGain
(Ch06)
AutoMixGain
(Ch07)
AutoMixGain
(Ch08)
Input
(Ch01)
Input
(Ch02)
:
Input
(Ch05)
Input
(Ch06)
Input
(Ch07)
Input
(Ch08)
Output
(Ch01)
Output
(Ch02)
:
Output
(Ch05)
Output
(Ch06)
Output
(Ch07)
Output
(Ch08)

Type
level

- : 00 (unused data)
* : Input level which applied Weight parameter

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

119

8. Meter List
*5 Dugan Automixer 9 - 16 Channel

10

9
Level (*)
(Ch01)
Level (*)
(Ch02)
:
Level (*)
(Ch09)
-

:
13

:
-

10
Level (*)
(Ch01)
Level (*)
(Ch02)
:
Level (*)
(Ch09)
Level (*)
(Ch10)
:
-

14

-

-

··

Mic Input Channel
13
Level (*)
(Ch01)
Level (*)
(Ch02)
:
Level (*)
(Ch09)
Level (*)
(Ch10)
:
Level (*)
(Ch13)
-

15

-

-

··

-

14
Level (*)
(Ch01)
Level (*)
(Ch02)
:
Level (*)
(Ch09)
Level (*)
(Ch10)
:
Level (*)
(Ch13)
Level (*)
(Ch14)
-

16

-

-

··

-

-

17

:
29

:
-

AutoMixGain
(Ch01)
AutoMixGain
(Ch02)
:
AutoMixGain
(Ch09)
AutoMixGain
(Ch10)
:
-

··

26

AutoMixGain
(Ch01)
AutoMixGain
(Ch02)
:
AutoMixGain
(Ch09)
-

30

-

-

··

AutoMixGain
(Ch01)
AutoMixGain
(Ch02)
:
AutoMixGain
(Ch09)
AutoMixGain
(Ch10)
:
AutoMixGain
(Ch13)
-

31

-

-

··

-

AutoMixGain
(Ch01)
AutoMixGain
(Ch02)
:
AutoMixGain
(Ch09)
AutoMixGain
(Ch10)
:
AutoMixGain
(Ch13)
AutoMixGain
(Ch14)
-

32

-

-

··

-

-

33

:
45

:
-

Input
(Ch01)
Input
(Ch02)
:
Input
(Ch09)
Input
(Ch10)
:
-

··

42

Input
(Ch01)
Input
(Ch02)
:
Input
(Ch09)
-

46

-

-

··

Input
(Ch01)
Input
(Ch02)
:
Input
(Ch09)
Input
(Ch10)
:
Input
(Ch13)
-

47

-

-

··

-

Input
(Ch01)
Input
(Ch02)
:
Input
(Ch09)
Input
(Ch10)
:
Input
(Ch13)
Input
(Ch14)
-

48

-

-

··

-

-

49

:
62

:
-

Output
(Ch01)
Output
(Ch02)
:
Output
(Ch09)
Output
(Ch10)
:
-

··

58

Output
(Ch01)
Output
(Ch02)
:
Output
(Ch09)
-

63

-

-

··

Output
(Ch01)
Output
(Ch02)
:
Output
(Ch09)
Output
(Ch10)
:
Output
(Ch13)
-

63

-

-

··

-

Output
(Ch01)
Output
(Ch02)
:
Output
(Ch09)
Output
(Ch10)
:
Output
(Ch13)
Output
(Ch14)
-

64

-

-

··

-

-

No.
1
2
:
9

18
:
25

34
:
41

50
:
57

··
··
··
··
··
··
··
··

··
··
··
··
··
··

··
··
··
··
··
··

··
··
··
··
··
··

15
Level (*)
(Ch01)
Level (*)
(Ch02)
:
Level (*)
(Ch09)
Level (*)
(Ch10)
:
Level (*)
(Ch13)
Level (*)
(Ch14)
Level (*)
(Ch15)
AutoMixGain
(Ch01)
AutoMixGain
(Ch02)
:
AutoMixGain
(Ch09)
AutoMixGain
(Ch10)
:
AutoMixGain
(Ch13)
AutoMixGain
(Ch14)
AutoMixGain
(Ch15)
Input
(Ch01)
Input
(Ch02)
:
Input
(Ch09)
Input
(Ch10)
:
Input
(Ch13)
Input
(Ch14)
Input
(Ch15)
Output
(Ch01)
Output
(Ch02)
:
Output
(Ch09)
Output
(Ch10)
:
Output
(Ch13)
Output
(Ch14)
Output
(Ch15)
-

16
Level (*)
(Ch01)
Level (*)
(Ch02)
:
Level (*)
(Ch09)
Level (*)
(Ch10)
:
Level (*)
(Ch13)
Level (*)
(Ch14)
Level (*)
(Ch15)
Level (*)
(Ch16)
AutoMixGain
(Ch01)
AutoMixGain
(Ch02)
:
AutoMixGain
(Ch09)
AutoMixGain
(Ch10)
:
AutoMixGain
(Ch13)
AutoMixGain
(Ch14)
AutoMixGain
(Ch15)
AutoMixGain
(Ch16)
Input
(Ch01)
Input
(Ch02)
:
Input
(Ch09)
Input
(Ch10)
:
Input
(Ch13)
Input
(Ch14)
Input
(Ch15)
Input
(Ch16)
Output
(Ch01)
Output
(Ch02)
:
Output
(Ch09)
Output
(Ch10)
:
Output
(Ch13)
Output
(Ch14)
Output
(Ch15)
Output
(Ch16)

Type
level

- : 00 (unused data)
* : Input level with Weight parameter applied

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

120

8. Meter List
*6 Dugan Automixer 17 - 24 Channel

18

17
Level (*)
(Ch01)
Level (*)
(Ch02)
:
Level (*)
(Ch17)
-

:
21

:
-

18
Level (*)
(Ch01)
Level (*)
(Ch02)
:
Level (*)
(Ch17)
Level (*)
(Ch18)
:
-

22

-

-

··

Channel
21
Level (*)
(Ch01)
Level (*)
(Ch02)
:
Level (*)
(Ch17)
Level (*)
(Ch18)
:
Level (*)
(Ch21)
-

23

-

-

··

-

22
Level (*)
(Ch01)
Level (*)
(Ch02)
:
Level (*)
(Ch17)
Level (*)
(Ch18)
:
Level (*)
(Ch21)
Level (*)
(Ch22)
-

24

-

-

··

-

-

25

:
45

:
-

AutoMIxGain
(Ch01)
AutoMIxGain
(Ch02)
:
AutoMIxGain
(Ch17)
AutoMIxGain
(Ch18)
:
-

··

42

AutoMIxGain
(Ch01)
AutoMIxGain
(Ch02)
:
AutoMIxGain
(Ch17)
-

46

-

-

··

AutoMIxGain
(Ch01)
AutoMIxGain
(Ch02)
:
AutoMIxGain
(Ch17)
AutoMIxGain
(Ch18)
:
AutoMIxGain
(Ch21)
-

47

-

-

··

-

AutoMIxGain
(Ch01)
AutoMIxGain
(Ch02)
:
AutoMIxGain
(Ch17)
AutoMIxGain
(Ch18)
:
AutoMIxGain
(Ch21)
AutoMIxGain
(Ch22)
-

48

-

-

··

-

-

49

:
69

:
-

Input
(Ch01)
Input
(Ch02)
:
Input
(Ch17)
Input
(Ch18)
:
-

··

66

Input
(Ch01)
Input
(Ch02)
:
Input
(Ch17)
-

70

-

-

··

Input
(Ch01)
Input
(Ch02)
:
Input
(Ch17)
Input
(Ch18)
:
Input
(Ch21)
-

71

-

-

··

-

Input
(Ch01)
Input
(Ch02)
:
Input
(Ch17)
Input
(Ch18)
:
Input
(Ch21)
Input
(Ch22)
-

72

-

-

··

-

-

73

:
93

:
-

Output
(Ch01)
Output
(Ch02)
:
Output
(Ch17)
Output
(Ch18)
:
-

··

90

Output
(Ch01)
Output
(Ch02)
:
Output
(Ch17)
-

94

-

-

··

Output
(Ch01)
Output
(Ch02)
:
Output
(Ch17)
Output
(Ch18)
:
Output
(Ch21)
-

95

-

-

··

-

Output
(Ch01)
Output
(Ch02)
:
Output
(Ch17)
Output
(Ch18)
:
Output
(Ch21)
Output
(Ch22)
-

96

-

-

··

-

-

No.
1
2
:
17

26
:
41

50
:
65

74
:
89

··
··
··
··
··
··
··
··

··
··
··
··
··
··

··
··
··
··
··
··

··
··
··
··
··
··

23
Level (*)
(Ch01)
Level (*)
(Ch02)
:
Level (*)
(Ch17)
Level (*)
(Ch18)
:
Level (*)
(Ch21)
Level (*)
(Ch22)
Level (*)
(Ch23)
AutoMIxGain
(Ch01)
AutoMIxGain
(Ch02)
:
AutoMIxGain
(Ch17)
AutoMIxGain
(Ch18)
:
AutoMIxGain
(Ch21)
AutoMIxGain
(Ch22)
AutoMIxGain
(Ch23)
Input
(Ch01)
Input
(Ch02)
:
Input
(Ch17)
Input
(Ch18)
:
Input
(Ch21)
Input
(Ch22)
Input
(Ch23)
Output
(Ch01)
Output
(Ch02)
:
Output
(Ch17)
Output
(Ch18)
:
Output
(Ch21)
Output
(Ch22)
Output
(Ch23)
-

24
Level (*)
(Ch01)
Level (*)
(Ch02)
:
Level (*)
(Ch17)
Level (*)
(Ch18)
:
Level (*)
(Ch21)
Level (*)
(Ch22)
Level (*)
(Ch23)
Level (*)
(Ch24)
AutoMIxGain
(Ch01)
AutoMIxGain
(Ch02)
:
AutoMIxGain
(Ch17)
AutoMIxGain
(Ch18)
:
AutoMIxGain
(Ch21)
AutoMIxGain
(Ch22)
AutoMIxGain
(Ch23)
AutoMIxGain
(Ch24)
Input
(Ch01)
Input
(Ch02)
:
Input
(Ch17)
Input
(Ch18)
:
Input
(Ch21)
Input
(Ch22)
Input
(Ch23)
Input
(Ch24)
Output
(Ch01)
Output
(Ch02)
:
Output
(Ch17)
Output
(Ch18)
:
Output
(Ch21)
Output
(Ch22)
Output
(Ch23)
Output
(Ch24)

Type
level

- : 00 (unused data)
* : Input level with Weight parameter applied

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

121

8. Meter List

8.3. XMV Series
Model
4ch

8ch

o

4ch D

8ch D

o
o

o

Category

Meter Name
INPUT

o
20001

o
o

Access ID
MemNo
(Memory UniqueId
Number)
512
20000
-

o

-

OUTPUT

Meter 4 Channel
(ANALOG INPUT A-D,
DIGITAL INPUT A-D)
Meter 8 Channel
(ANALOG INPUT A-H,
DIGITAL INPUT A-H)
Meter 4 Channel
(OUTPUT A-D)
Meter 8 Channel
(OUTPUT A-H)

Type
level

Remarks
See 6. Parameter
Value Details.

level
level
level

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

122

8. Meter List

8.4. EXi8
Access ID
MemNo
UniqueId
(Memory Number)
512
20000

Category
-

Meter Name
INPUT

Meter 8 Channel
(INPUT1-8)

Type
level

Remarks
See Parameter Value Details.

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

123

8. Meter List

8.5. EXo8
Access ID
MemNo
UniqueId
(Memory Number)
512
20001

Category
-

Meter Name
OUTPUT

Meter 8 Channel
(OUTPUT1-8)

Type
level

Remarks
See Parameter Value Details.

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.1.0 rev10

124