Youngshin Electronics J2000S Transceiver of Car Alarm/Remote Engine Starter User Manual

Youngshin Electronics Co., LTD. Transceiver of Car Alarm/Remote Engine Starter Users Manual

Contents

Users Manual

Page 1 of 8 - 1
-
CompuStar 2000AS
USER’S GUIDE
Firstech, Inc. 801 E. 82nd Ave
Suite 1
Anchorage AK. 99518
(907) 563-8648
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
CAUTION: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this device.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Page 2 of 8 - 2
-
INTRODUCTION
Thank you for choosing COMPUSTAR, a state-of-the-art TWO WAY
alarm/remote start systems for your vehicle. We, at FIRSTECH, INC., are
constantly researching and developing to make you and your vehicle safe and
more comfortable. SECURITY & COMFORT, that’s what FIRSTECH, INC. is all
about.
TABLE OF CONTENTS
1. Transmitter Button functions ---------------------------------------------------Page 3
2. Alarm Function------------------------------------------------------------------------Page 3
3. Panic-------------------------------------------------------------------------------------Page 3
4. Start Function--------------------------------------------------------------------------Page 3
5. Safety Shutdown----------------------------------------------------------------------Page 4
6. VPS(Vehicle Paging System)------------------------------------------------------Page 4
7. Aux 1 and Aux 2-----------------------------------------------------------------------Page 4
8. Valet Mode and Valet Switch------------------------------------------------------Page 4
9. Shock Sensor--------------------------------------------------------------------------Page 4
10. Timer Start-----------------------------------------------------------------------------Page 4
11. 2nd Car----------------------------------------------------------------------------------Page 4
12. Transmitter Learning Procedure-------------------------------------------------Page 4
13. Programming Options with Transmitter----------------------------------------Page 5
14. Warranty Statement-----------------------------------------------------------------Page 7
15. Registration Card---------------------------------------------------------------------Page 8
Page 3 of 8 - 3
-
1. Transmitter Button Functions
Channel Button Press
for Function Factory
Setting
1. I 1/2 sec Arm/Disarm; VPS on/off
2. II 1/2 sec Aux 1
3. III 1/2 sec Aux 2
4. IV 1/2 sec Query
5. I - 2 sec Panic
6. II - 2 sec Remote Starting - On/Off
7. III- 2 sec Trunk
8. IV- 2 sec CompuGlo Back Light On/Off On
9. (I+II) 1/2 sec Siren Chip - On/Off On
10. (I+III) 1/2 sec Valet Mode - On/Off Off
11. (I+IV) 1/2 sec Shock Sensor On/Off On
12. (II+III) 1/2 sec Transmitter Beep - On/Off On
13. (II+IV) 1/2 sec Timer Mode 1.5 hour - On/Off Off
14. (III+IV) 1/2 sec 2nd Car Off
15. (I+II)- 2 sec Option Programming 1
16. (I+III)- 2 sec Option Programming 2
2. Alarm Function
Upon arming, your alarm will be triggered by:
• Light Impact (first stage shock sensor). The siren will chirp 4 times and the parking
lights will flash for a few seconds. The transmitter will be paged and the vibration
icon will appear in the LCD.
• Heavy impacts (second stage shock sensor). The siren will go off and the parking
lights flash for 60 Seconds. The transmitter will be paged and the Hammer in the
LCD will appear.
• Door opened. The siren will go off and the parking lights will flash for 60 Seconds.
The transmitter will be paged and the door icon will appear in the LCD.
• If you have installed the Optional starter kill function, your vehicle will not start with
key when system is armed.
Note: (Siren duration 30Sec. or 60Sec. refer to programming section)
3. Panic
In Case of an emergence and you want to track attention. Press Button I for 2 Seconds
and you will enter Panic Mode. The siren will go off and the parking light will start
flashing. To disengage Panic Mode. Press Button I for ½ Second.
Page 4 of 8 - 4
-
4. Start Function
Press Button II for 2 Seconds to start the engine. The engine will start and give you a
confirmation on the Remote-pager. The engine will run 15 minutes (25 min for diesel) or
25 minutes (40 min for diesel) . If the engine has a problem starting the system will retry
2 more times. If the engine dose not start after the 3rd attempt, please call you
Authorized Dealer.
Note: Runtime, please consult you Authorized Dealer.
5. Safety Shut Down
System has several Shut Down inputs. That will shut down the engine or prevent from
remote starting.
• the Hood is opened,
• the Brake is pressed,
• the Valet is entered, or
• the Valet switch is turned on.
6. VPS(Vehicle Paging System)
VPS is turned on upon arming. If the VPS sensor is triggered by an impact such as
knocking on the VPS module, the transmitter will be paged.
7. Aux 1 & Aux 2
The system has Aux 1 & Aux 2 output to be utilized with optional features. (Consult your
Authorized Dealer)
8. Valet Mode and Valet Switch
To enter Valet mode, press Buttons I & III simultaneously for ½ Second or insert the key
into the ignition and tuned the ignition on and off five times within 10 seconds. In Valet
mode, the system will only activate Locks, Trunk, and the Auxiliary only. To exit Valet
Mode press Button I & III simultaneously for ½ Second.
9. Shock Sensor
Dual Stage Shock Sensor will activate 30 Sec. after the system is Armed (Locked).
When 1st stage is triggered the siren will chirp 4 times and Remote-pager will receive a
notification of the violation.(Vibration Icon will appear) When 2nd stage is triggered the
siren will activate and Remote-pager will receive a notification of the violation.(Hammer
will appear)
10. Timer Mode
To enter the Timer Mode press Buttons II & IV simultaneously for ½ Second. The
system will start every 1.5 Hrs. till Timer Mode is deactivated and automatically canceled
if the vehicle is started with the Key or Remotely. To Exit Timer Mode press Button II &
IV simultaneously for ½ Second again.
11. 2nd Car Mode
System is able to operate 2nd vehicle. Press Buttons III & IV simultaneously for ½
Second. Feature may be different for 2nd vehicle regards to options. To Exit 2nd Car
press Button III & IV simultaneously again. (Consult your Authorized Dealer)
Page 5 of 8 - 5
-
12. Transmitter Learning Procedure
Your transmitter has been programmed at the factory. However, if you replace or add
additional Remote-pager, follow this procedure.
Steps 1: Put the system in Valet mode with key: Ignition On and Off Five times with key
within 10 seconds. The parking light will flash once.
Step 2: Within 6 seconds, press any button for a half-second.
Step3:The parking light will flash twice to confirm Step 2.
Step 4: Program 2nd transmitter or 3rd transmitter by pressing any button. The system
will program up to 3 transmitters. The parking light will flash once to confirm Step 3.
13. Programming Options with Transmitter
Each unit comes with factory setting. If you want to change any of those settings, follow
this procedure.
Step one: Press Buttons I+II simultaneously for 2 seconds to change any of the Option
#1 options or Press Buttons I+III simultaneously for 2 seconds to change any of the
Option #2 options. Confirmed by chirp and parking light - one time.
Step two: Within 2 seconds press Button IV for the same number of time as the option
number you wish to change. Confirmed by chirp and parking light - same number of
time of the option number.
Step three: Press Button I a ½ second to change to the factory setting - confirmed by
chirp and parking light by one time. Press Button II a ½ second to change to the option
setting - confirmed by chirp and parking light by two times. If you hear one second chirp,
it means the unit did not receive any signal in this step – repeat Step one again.
Option #1: Option Programming (Press I and II simultaneously for 2 seconds)
No Options Factory Setting Option Setting
1. Factory Arm/Disarm/Rearm with Transmitter
Copier No Yes
2. The duration of Lock/Unlock pulse 0.5 sec 2.5 sec
3. Extended Cranking Time by .2 sec No Yes
4. Safety Unlock (Lock/Unlock/Unlock) No Yes
5. Double Pulse Unlock No Yes
6. Passive Arming No Yes
7. Passive Locking No Yes
8. Disarm with Trunk Unlock Yes No
9. Duration of the Siren Output 60 sec 30 sec
10. Factory Rearm with Dome-light No Yes
Page 6 of 8 - 6
-
Option #2: Option Programming (Press I and III simultaneously for 2 seconds)
No Options Factory Setting Option Setting
1. Harness #1, #5 Wire Ignition 2nd Starter
2. Aux 1 Output .5 sec See Note 1
3. Aux 2 Output .5 sec See Note 2
4. Ignition Lock No Yes
5. Siren Activation Deactivation
Note 1: Aux 1 continues output until Button II is pressed for 1/2 sec. again or Key On
whichever comes first.
Note 2: Aux 2 continues output until Button III is pressed for 1/2 sec. again or Key On
whichever comes first.
14. Option Resetting: To Reset to the factory default settings.
Step 1: Press Buttons I+II simultaneously or I+III simultaneously for 2 seconds.
Confirmed by chirp and parking light - one time.
Step 2: Press Button III three times. Confirmed by chirps and parking lights - three
times.
Page 7 of 8 - 7
-
15. Limited Lifetime Warranty
Firstech, Inc. Warrants to the original purchaser that this product shall be free of defects
in material and workmanship under normal use and circumstances for the period of time
that the original owner of this product owns the vehicle in which it is installed; except that
the remote controller unit for the period of one year from the date of installation to the
original owner of this product. When the original purchaser returns the product to the
retail store where it was purchased or pre-paid postal to Firstech, Inc., 230 E. Potter
Suite 8, Anchorage, Alaska 99518, USA within the warranty period, and if the product is
defective Firstech, Inc, will at its option repair or replace such.
“TO THE MAXIMUM EXTENT ALLOWED BY LAW, ANY AND ALL WARRANTIES ARE
EXCLUDED BY THE MANUFACTURER AND EACH ENTITY PARTICIPATING IN THE
STREAM OF COMMERCE THEREWITH. THIS EXCLUSION INCLUDES BUT IS NOT
LIMITED TO, THE EXCLUSION OF ANY AND ALL WARRANTY OF
MERCHANTABILITY AND/OR ANY AND ALL WARRANTY OF FITNESS FOR A
PARTICULAR PURPOSE AND/OR AHY AND ALL WARRANTY OF NON-
INFRINGEMENT OF PATENTS, IN THE UNITED STATES OF ANERICA AND/OF
ABROAD. NEITHER THE MANUFACTURER OR ANY ENTITIES CONNECTED
THEREWITH SHALL BE RESPONSIBLE OR LIABLE FOR ANY DAMAGES
WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL
DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR LOSS OF TIME, LOSS OF
EARNINGS, COMMERCIAL LOSS, LOSS OF ECOMONIC OPPORTUNITY AND THE
LIKE. NOTHWITHSTANDING THE ABOVE, MANUFACTURER DOES OFFER A
LIMITED WARRANTY TO REPLACE OR REPAIR THE CONTROL MODULE AS
DESCRIBED ABOVE. Some states do not allow limitations on how long an implied
warranty will last or the exclusion or limitation of incidental or consequential damages.
This warranty gives you specific legal rights, and you may also have other rights, which
vary State to State.
IMPORTANT NOTE:
A product’s warranty is automatically void if its date code or serial number is defaced,
missing, or altered. This warranty will not be valid unless you have completed the
warranty card and mailed it to Firstech, Inc., within 10 days after purchase to the
address listed on the card.
Page 8 of 8 - 8
-
16. Registration Card
Name__________________________________________________________
Address________________________________________________________
City__________________ State___________________ Zip____________
Phone Number: Home ( )_____________ Office ( )______________
Place of Purchase__________________________ Date of Purchase______
Purchase Model___________________ Purchase Price__________
Vehicle Make___________________ Model:_________________________
How did you hear about this product?_______________________________
Firstech Inc.
801 E. 82nd Ave. Suite 1
Anchorage, AK 99518

Navigation menu