Danalock V3 Product Manual Z Wave V 0.9.1

: Z-Wave Danalock V3 Product Manual Z Wave V 0.9.1 Danalock_V3_Product_manual_Z_Wave_V_0.9.1 733 docs

Open the PDF directly: View PDF .
Page Count: 6

1 | P a g e

Danalock V3 Product manual

The Danalock V3 Z-Wave is a secure electronic door lock that supports the Z-Wave Plus standard, which is

compatible with earlier versions of Z-Wave. The Danalock is battery supplied and therefore it is a FLIRS

Frequently Listening Routing Slave which conserves battery The Danalock V3 is a security enabled Z-Wave Plus

Product. A security enabled Z-Wave controller must be use. The Danalock V3 supports the standard security S0

and the new security standard S2. This manual covers all versions of Danalock V3 Z-Wave. This manual is

accompanied by the mounting manually for your specific lock.

Z-Wave interoperability

The Danalock can be included and operated in any Z-Wave network with other Z-Wave certified devices from

other manufacturers and/or other applications. All non-battery operated nodes within the network will act as

repeaters regardless of vendor to increase reliability of the network.

Z-Wave add/inclusion and remove/exclusion

• To add or include the Danalock into a Z-Wave network

1. Set the controller in inclusion mode

2. Push the switch once.

3. Wait 5 seconds.

• To remove or exclude the Danalock into a Z-Wave network

1. Set the controller in exclusion mode

2. Push the switch once.

3. Wait 5 seconds.

Factory Reset

The Danalock can be set to factory settings by pushing the switch ten times. Please use this procedure only

when the primary controller is missing or otherwise inoperable.

Batteries

The Danalock uses 4 CR123A batteries. Only use four new batteries

from the same manufacturer. Do not mix new and old batteries.

The Package contains

• Danalock V3

• Batteries (may not be included)

• Manual

• Adapters (may vary from country to country)

If the Danalock is firstly included on a Z-Wave network, the Bluetooth Smart is disabled because of security and

to conserve power. To enable Bluetooth Smart enable Configuration byte no. 5.

2 | P a g e

Supported Command Classes

Command Class

Version

Not added

Non-Secure

added

Securely added

Non-secure

CC

Secure CC

Z-Wave Plus Info

2

Support

Support

Support

Transport Service

2

Support

Support

Support

Security 0

1

Support

Support

Support

Security 2

1

Support

Support

Support

Association

2

Support

Association Grp Info

1

Support

Battery

1

Support

Configuration

1

Support

Device Reset Locally

1

Support

Door lock

2

Support

Firmware update MD

4

Support

Manufacturer Specific

2

Support

Notification

8

Support

Power level

1

Support

Superversion

1

Support

Version

2

Support

Node Info

Generic Device Class

0x40 GENERIC_TYPE_ENTRY_CONTROL

Specific Device Class

0x03 SPECIFIC_TYPE_SECURE_KEYPAD_DOOR_LOCK

Association CC V2 (secure)

Associations Groups

Group 1 is Lifeline. All unsolicited reports are sent to the node in Lifeline. The Danalock can send the following

commands through Lifeline:

ID

Name

Node Count

Description

1

Lifeline

1

Supports the following command classes:

• Device Reset Locally: triggered upon reset.

• Battery/notification: triggered upon low battery.

• Door Lock operation report: triggered upon a change in door lock

• Notification: triggered upon a change in door lock

Battery CC V1 (secure & unsecure)

The Battery Get request can be used to get the status of the battery. To get a useful battery level the motor of

the lock should be operated at least once for the lock to sample a meaningful battery level. When battery

level is low a battery warning is send to the controller.

3 | P a g e

Configuration CC V1 (secure)

Z-Wave

parameter

no.

Parameter Name

Parameter

Size

Default

value

Description

1

TWIST_ASSIST

1 Byte

0

0 = Disabled, 1=Enabled

2

HOLD_AND_RELEASE (brake and go back)

4 Bytes

0

0=Disabled, 1-2147483647

(hold seconds)

3

BLOCKED_2_BLOCKED(async)

1 Byte

0

0 = Disabled, 1=Enabled

4

BLE_TEMPORARY_ALLOW_TIMER

4 bytes

0

0=Disabled, 1-2147483647

(seconds to allow)

5

BLE_ALWAYS_ALLOWED

1 byte

0

0 = Disabled, 1=Enabled

6

Autolock

4 bytes

0

0 = Disabled, 1-2147483647

seconds of delay before

autolock enable.

Device Reset Locally CC V1 (unsecure)

When the Z-Wave module is reset it sends a report to tell the controller it has been reset. The lock is reset by

pushing the switch 10 times. Please use this procedure only when the primary controller is missing or otherwise

inoperable

Door Lock CC V2 (secure)

Door Lock Operation is used to lock and unlock the Danalock. See table to see how the Door Lock Mode

paramater affects the lock.

Door Lock Operation Paramater

Secured

Unsecured

Door Lock Mode

0xFF

0x00-0xEF

In a Door Lock Operation Report the Danalock will report:

Door Lock Operation Report

Value\Door status

Unlocked

Locked

Door Lock Mode

0x00

0xFF

Handles

0x11

0x11

Door Condition

0x02

0x05

Lock Timeout Minutes

0xFE

0xFE

Lock Timeout Seconds

0xFE

0xFE

The Danalock does not use the Door Lock Configuration to adjust settings, the Configuration CC is used

instead. The Danalock ignores Door Lock Configuration Set frames and response a Door Lock Configuration

Get with:

Door Lock Configuration Report

Parameter

Value

Operation Type

Constant operation(0x01)

Handles

Handle 1 enabled (0x11)

Lock Timeout Minutes

Timeout not supported(0xFE)

Lock Timeout Seconds

Timeout not supported(0xFE)

4 | P a g e

Firmware Update Meta Data CC V4 (secure)

The Danalock supports firmware update of the Z-Wave module over the air.

The firmware upgrade takes ~30 min with S0 and ~20 min with S2.

Firmware ID = 0x0A01.

Firmware 0 ID = 0x0000.

Manufacture Specific CC V2 (secure & unsecure)

Value

Comment

Manufacturer ID

0x010E

Poly-control

Product Type ID

0x0009

Danalock V3 Series

Product ID

0x0001

Lock

The Device specific report returns the 6 byte long DMI serial number of the host.

Notification CC V8 (secure)

The Notification CC is implemented as a push only, which means only pushes notification to the controller.

Sequence number is not supported.

Supported notifications

Notification Type

Event

Comments

Access Control

(0x06)

Manual Lock Operation (0x01)

User Touch button used to lock the door.

Manual Unlock Operation (0x02)

User Touch button used to unlock the door.

RF Lock Operation (0x03)

Bluetooth or Z-wave initiated the operation

RF Unlock Operation (0x04)

Bluetooth or Z-wave initiated the operation

Auto Lock Locked Operation(0x09)

The Auto Latch time has locked the door. Not

used. Auto locks sends (0x01) instead.

Lock Jammed (0x0B)

The lock/unlock operation could not be

completed.

Power Level CC V1 (secure & unsecure)

Can be used under inclusion to test signal strength from the controller and to the device.

Security CC V1 (secure & unsecure)

See Z-Wave documentation.

5 | P a g e

Security CC V2 (secure & unsecure)

The Danalock support S2_ACCESS security class.

Superversion V1 (secure)

See Z-Wave documentation.

Transport Service V2 (secure)

See Z-Wave documentation.

Version CC V2 (secure)

This Command Class is used to get information about which version of the different command classes

the Danalock supports and the software version of the Danalock.

Version Report

Z-Wave Library Type

ZW_LIB_SLAVE_ENHANCED(0x03)

Z-Wave Protocol Version

0x04 (SDK v6.71.01)

Z-Wave Protocol Sub Version

0x3D (SDK v6.71.01)

Firmware 0 version

Version of the firmware on the Z-Wave module

Version

Subversion

Comments

1

2

First release

Firmware 1 version

Version of the firmware on the Host.

Version

Subversion

Comments

0

7

First release

Hardware version

0x02

Danalock V3

Z-Wave Plus Info CC V2 (secure & unsecure)

Z-Wave Plus Info

RoleType

0x07 ROLE_TYPE_SLAVE_SLEEPING_LISTENING

NodeType

0x00 NODE_TYPE_ZWAVEPLUS_NODE

InstallerIconType

0x03 ICON_TYPE_GENERIC_DOOR_LOCK_KEYPAD

UserIconType1

0x03 ICON_TYPE_GENERIC_DOOR_LOCK_KEYPAD

6 | P a g e

Controller Integration

When the Danalock has been included into the network, the controller should:

• Set the Lifeline. Association group 1

• Enable Notification for Access Control

Test information

Configuration Parameters

When testing config parameter 4. Be aware that this is a count down, so a set and then a get will not return the

same value.

Battery Warning

To get the lock to send a battery warning the voltage must be low AND the motor must be operated. The lock

only measures the battery voltage under load to get the most precise result. By using a 1 A voltage adjustable

transformer with approximately 1 meter of wire the following data has been collected.

Voltage

Battery report value

12 V

0x62 (98%)

9V

0x26 (38%)

7,5V

0x0B (11%) (Battery warning is send)

No reports received

If no reports are received from the lock it is most likely because the lock is not calibrated and thereby does not

no know when the lock is lock or unlock and therefore it does not send reports to the gateway. There are two

ways to calibrate the lock.

1. Autocalibration. Turn the Danalock manually until the door is unlocked and leave the door open while

calibrating. Lift the handle if needed. Now click 3 times, after 5 seconds the Danalock will calibrate.

2. Manual calibration (start by turn to unlock). Turn the Danalock completely into unlock position, then

click twice. Wait 5 seconds until it flashes yellow, then turn the Danalock into locked position and click

once.