ZMODO Technology H2401 Tune User Manual 1

Download:
Mirror Download [FCC.gov]
Document ID	3716201
Application ID	Uya9+BTzmLTiJdg4edr8Lw==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	73.18kB (914711 bits)
Date Submitted	2018-01-16 00:00:00
Date Available	2018-01-16 00:00:00
Creation Date	2017-11-14 18:38:37
Producing Software	Corel PDF Engine Version 16.1.0.843
Document Lastmod	2017-11-14 18:38:37
Document Title	未命名 -1
Document Creator	CorelDRAW X6
Document Author:	Sharon liu

757880306 SD-H2401 快操 REV-A00
尺寸：90*130mm
材质：105g铜版纸 双面印刷4c+1专 折页
3 Mobile Setup
What’s in the box:
1 Getting to know your Tune
There's comfortable, and then there's bliss. Zmodo Tune
is a smart thermostat that controls and fine tunes your
temperature to make sure that your home feels exactly the
way you like it. You can control your Tune from anywhere
with your smartphone or tablet, and program it to adjust
your temperature automatically. It also works with Room
Sensors to make sure that your home is perfectly
configured to your liking.
W2
W1
O/B
RC
RH
Screws & Anchors (3)
Quick Guide
WiFi Status Light*
Current / Target Temperature**
Decrease Temperature
Room Sensors (2)
Select the network named “ZMD_SAP”
and connect to it.
(Only included in select configurations)
Increase Temperature
Level
Wire Connectors
Toggle HVAC Mode
Current HVAC Mode Indicator
(Cooling / Heating / Fan Only)
*When the WiFi Status Light is solid, it means that Tune is successfully
connected to the WiFi network. When the light is flashing, it means that Tune
is not yet connected to the WiFi network.
**When you are setting the temperature, the display will show the target
temperature. After 5 seconds, it will display the current temperature.
2 Installation
Zmodo
Note: If you see a "No Internet Connection" error
message, please ignore it and connect anyway.
Make sure that your Tune is powered on before
proceeding with the setup.
We are constantly working to improve our product and app. Please visit
www.zmodo.com/support for updated instructions, manuals, and more.
1 Remove your old thermostat cover. Some thermostats
NO
can be popped off from the base, while others may need
to be unscrewed first.
Heating and cooling: one stage of heating and cooling,
and a second stage of either heating or cooling.
Heat pumps: with auxiliary and emergency heat.
Fans: one speed.
Select the “Zink” connection method
to connect your Tune. Your Tune will
be added to your Zmodo account.
Before you begin:
You will need a strong 2.4GHz WPA-PSK/WPA2-PSK WiFi
network near your Tune.
Zmodo Tune is compatible with most of the 24V HVAC
system and not compatible with high voltage (110V, 220V)
systems.
It can control:
Return to the Zmodo app page and
select or enter the SSID and password
of the WiFi network that you want your
Tune to connect to.
10
11
Select the WiFi network that your Tune
will connect to, and connect to it.
Return to the Zmodo app once your
mobile device is connected to the WiFi
network.
12
Your Tune has been successfully
configured!
Note: The WiFi name and password are casesensitive.
Rc RH G Y w C
Tap √ to proceed.
If there is no C wire connected, please purchase a Tune
Power Accessory and follow the instructions on its quick
guide to complete the installation.
Incompatible wiring and voltage
IMPORTANT! Before you begin, make sure that the power
to your thermostat is turned off. Check your circuit breaker
for a switch. To make sure that it's off, try changing the
temperature with your thermostat. Wait a few minutes, and
check the vents. No air should be coming out of the vents.
Download and install the "Zmodo" app from Google PlayTM
or the App StoreTM (Compatibility: iOS ® 7.0+ or AndroidTM
4.0+). Launch the app and sign up for a free Zmodo
account. All of your devices will be bound to this account.
W1 W1
Stranded wires: Stranded wires aren't compatible with
Tune.
High-voltage wires: If your old thermostat is labelled as
120V or 240V, has thick wires with wire nuts, or as L1 and
L2 terminal blocks, the system is high-voltage and isn't
compatible with Tune.
Follow the on-screen instructions and
select “Tap here to begin setup” to go
to the WiFi settings page on your
smartphone.
Mounting Base
Tune Thermostat
Tune works with most 24V systems, including forced air,
heat pump and radiant systems, as well as common fuel
types such as natural gas, electricity and oil.
R c Rc
W2 W2
Wire Label Stickers
Quick Start Guide
Tap √ to proceed.
Log in and press + in the upper
right corner. Select "Add Device".
Make sure you know the SSID (WiFi network name) and
password of the 2.4GHz WPA-PSK/WPA2-PSK WiFi
network that you want your Tune to connect to. Your
network cannot be hidden.
R H RH
Tune
Before you begin:
Tune
Quick Start Guide
Y1 Y1
This device can be set up with a Zmodo Beam. If you own a
Beam, please follow the instructions in your Beam quick guide to
connect your device instead.
www.zmodo.com/support
Y2 Y2
Y1
Beam
The following instructions will help you configure your
Tune for initial use. For detailed instructions and
troubleshooting, please visit:
Tune
Y2
Connect
with
3 Take a picture of the wires and save it for reference,
2 Please check if your old thermostat has a C wire
connected. If it doesn't have a C wire connected, you
will need to buy a Tune Power Accessory in order to
install your Tune. Follow the instructions in your Power
Accessory quick guide to complete the installation.
label the wires using the provided wire labels. Take the
provided wire labels and attach the appropriate labels
to the matching wires on the thermostat.
The app will automatically search for
your Tune and connect it to the WiFi
network. This may take a few
minutes.
10
4 Connecting your Room Sensors (optional)
Note: If your package includes Room Sensors, please read the following
before configuring your sensors.
Tune Room Sensors can detect whether anyone’s home to
deliver perfect comfort when you’re at home or save
energy when you’re not. Each sensor can read the
temperature and detect when a person is in the room to
deliver the right temperature to the room that matters the
most. For more information on how this works, please visit
the corresponding FAQ at www.zmodo.com/support
If you do not see this screen, please
proceed to step 8.
Note: Label your wires: R or Rh → Rh, Rc → Rc, W/W1 → W1, W2 → W2,
Y/Y1 →Y1, Y2 →Y2
If you have a jumper between Rc, Rh, or R, leave it alone. Only label the
wires that run from your wall into a terminal block.
YES
If you see this screen, the app will
connect your Tune to your WiFi
network. This may take a few minutes.
Once it’s completed, please skip to
step 11.
If this app interface appears, please
press “Tap here to select WiFi”.
11
Name your Tune and set a password
for it. Tap √ to proceed.
1 Plug the room sensor into a power outlet in a room that you
w1
Note: The password provides an additional layer
of security for your devices. You will not need to
use this password when accessing your devices
from the Zmodo app. It is not required, but it is
highly recommended.
Rc RH G Y w C
Rc RH G Y w C
frequently visit. Avoid installing in areas exposed to direct
sunlight or near objects that radiate excessive heat.
2 Open the Zmodo App, access your Tune's Device Settings,
If there is a C wire connected, please continue with
instructions in this guide.
4 Disconnect the wires and remove your old thermostat's
base. Make sure that the wires do not fall into the hole
in the wall. You can store your old thermostat and base
for safe-keeping.
7 Fasten the mounting base onto the wall. Tap the wall
anchors with a hammer until the anchors are flush
against the wall. Pull the wires through the center hole of
the mounting base, and use the provided screws to
fasten the mounting base to the wall.
9 Attach your Tune to the mounting base.
Y1
W2
Y2
W1
O/B
RC
RH
5 Remove the mounting base from your Zmodo Tune.
8 Connect the wires with the matching connectors. Match
6 Mark and drill the appropriate holes in the wall for the
mounting base. Line the mounting base against the
surface where you will install your Tune and mark the
wall with three corresponding holes for screws. Use the
level to make sure the mounting base is level. Drill three
holes slightly smaller than the wall anchors.
the wires with the labels with the corresponding wire
connectors, and connect the wires to the mounting base.
Press the tab down and insert the exposed wire into the
connector. Release until the connector grips the wire.
Once connected, gently tuck each wire into the hole as
shown and make sure that the connections are secure.
Y1
W2
Y2
W1
O/B
RC
3 In the app, you will be able to define which rooms are the
most important, and set target temperatures for each
room. For example, you can place a Room Sensor in your
bedroom, set the target temperature to 78°F, and give it
top priority. You have another sensor in your living room,
with a target temperature set to 75°F. If people are
detected both in your bedroom and living room, Tune will
turn on the HVAC until your bedroom is 78°F. If people are
detected in your living room but not your bedroom, Tune
will turn on the the HVAC until your living room is 75°F.
sure that your Tune was properly connected, try to
manually adjust the temperature. Wait a few minutes,
and check if any air comes out of your vents.
Note: If you were unable to power on your Tune:
Please Turn off the power to your thermostat and remove your Tune from its
mounting base. If your system has both Rh and Rc connected, and you are
connecting the Rh wire to the Rh connector and the Rc wire to the Rc
connector, please swap them and connect the Rh wire to the Rc connector,
and the Rc wire to the Rh connector. Attach your Tune to the mounting base
and restore the power to your thermostat.
正面
Adjust your temperature from anywhere at any time
Tune can be controlled from the Zmodo app on your
smartphone, allowing you to adjust your thermostat
settings whenever you want, no matter where you are.
Learns your habits and automatically adjusts
During the learning period (first week after installation),
Tune will pick up on your preferences. The more you
adjust your temperature, the more Tune learns your
preferences. Over time, Tune will be able to adjust your
temperature automatically, just the way you like it.
Works with Zmodo Smart Vents (not yet available)
Tune will work with the upcoming Zmodo Smart Vents.
When used together with Room Sensors, the Smart Vents
will be able to control the air flow so that each room is set
to the temperature that you want.
For more information on how your Tune, the Room Sensors,
and the Smart Vents work together, visit the corresponding
FAQ on www.zmodo.com/support.
RH
14
FCC Statement
6 Support
changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Having difficulty?
You can use the Live Chat function in Zmodo app if you
have any technical problems.
Please follow the steps below:
Access the “Me” page in the bottom right corner of the
Zmodo app and select “Zmodo Support”.
For more instructions, troubleshooting, support, and other
resources, please visit:
5 Main Features
10 Turn the power to your thermostat back on. To make
13
12
15
and choose the "Accessories" option. Select the + Add
Accessory option and follow the on-screen instructions.
When the app prompts you to press a button, wave in front
of the room sensor to pair it with your Tune.
www.zmodo.com/support
Like us on Facebook.com/Zmodo
Scan the QR-code below!
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation.If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator and your body. This
transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Follow us on Twitter @Zmodo
Scan the QR-code below!
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Android is a trademark of Google Inc. Google Play is a trademark of Google
Inc. Apple, the Apple logo, and iPhone are trademarks of Apple Inc.,
registered in the U.S. and other countries. Apple Store is a service mark of
Apple Inc.
16
REV-A00
背面

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Profile CMM Type                : Lino
Profile Version                 : 2.1.0
Profile Class                   : Display Device Profile
Color Space Data                : RGB
Profile Connection Space        : XYZ
Profile Date Time               : 1998:02:09 06:49:00
Profile File Signature          : acsp
Primary Platform                : Microsoft Corporation
CMM Flags                       : Not Embedded, Independent
Device Manufacturer             : IEC
Device Model                    : sRGB
Device Attributes               : Reflective, Glossy, Positive, Color
Rendering Intent                : Perceptual
Connection Space Illuminant     : 0.9642 1 0.82491
Profile Creator                 : HP
Profile ID                      : 0
Profile Copyright               : Copyright (c) 1998 Hewlett-Packard Company
Profile Description             : sRGB IEC61966-2.1
Media White Point               : 0.95045 1 1.08905
Media Black Point               : 0 0 0
Red Matrix Column               : 0.43607 0.22249 0.01392
Green Matrix Column             : 0.38515 0.71687 0.09708
Blue Matrix Column              : 0.14307 0.06061 0.7141
Device Mfg Desc                 : IEC http://www.iec.ch
Device Model Desc               : IEC 61966-2.1 Default RGB colour space - sRGB
Viewing Cond Desc               : Reference Viewing Condition in IEC61966-2.1
Viewing Cond Illuminant         : 19.6445 20.3718 16.8089
Viewing Cond Surround           : 3.92889 4.07439 3.36179
Viewing Cond Illuminant Type    : D50
Luminance                       : 76.03647 80 87.12462
Measurement Observer            : CIE 1931
Measurement Backing             : 0 0 0
Measurement Geometry            : Unknown
Measurement Flare               : 0.999%
Measurement Illuminant          : D65
Technology                      : Cathode Ray Tube Display
Red Tone Reproduction Curve     : (Binary data 2060 bytes, use -b option to extract)
Green Tone Reproduction Curve   : (Binary data 2060 bytes, use -b option to extract)
Blue Tone Reproduction Curve    : (Binary data 2060 bytes, use -b option to extract)
Page Count                      : 1
Create Date                     : 2017:11:14 18:38:37+08:00
Modify Date                     : 2017:11:14 18:38:37+08:00
Producer                        : Corel PDF Engine Version 16.1.0.843
Author                          : Sharon liu
Creator                         : CorelDRAW X6
Title                           : 未命名 -1

EXIF Metadata provided by EXIF.tools