ZTE AC8700 CDMA 2000 EV-DO Wireless DATA Terminal User Manual
ZTE Corporation CDMA 2000 EV-DO Wireless DATA Terminal
ZTE >
Users Manual
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
ZTE Corporation http//wwwztecomcn
CDMA2000 1X EV-DO
Wireless Data Terminal
User Guide
This User Guide applies to Wireless Data Terminal of MG478 and AC8700.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
ZTE Corporation http//wwwztecomcn
Copyright Statement
Copyright © 2006 by ZTE Corporation
All rights reserved.
No part of this publication may be excerpted, reproduced, translated or utilized in any form or by
any means, electronic or mechanical, including photocopying and microfilm, without the prior
written permission of ZTE Corporation.
ZTE Corporation reserves the right to make modifications on print errors or update specifications
in this manual without prior notice.
V1.0, August, 2006
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
ZTE Corporation http//wwwztecomcn
Table of Contents
1. Introduction.............................................................................................................................1
2. Specification ...........................................................................................................................1
3. Precautions..............................................................................................................................1
4. Appearance .............................................................................................................................2
4.1 Introduction.........................................................................................................................2
4.2 Insert R-UIM Card ..............................................................................................................3
5. Install and Uninstall................................................................................................................4
5.1Windows 2000 ...................................................................................................................5
5.1.1 Install........................................................................................................................5
5.1.2 Uninstall...................................................................................................................9
5.2Windows XP ....................................................................................................................10
5.2.1 Install......................................................................................................................10
5.2.2 Uninstall.................................................................................................................14
6. Run the Application ..............................................................................................................15
7. Connect/Disconnect..............................................................................................................16
8. Connection Records..............................................................................................................17
9. Setting...................................................................................................................................18
10. Help ......................................................................................................................................20
11. Connect to the Website .........................................................................................................20
12. Trouble-shooting...................................................................................................................21
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
ZTE Corporation http//wwwztecomcn
1. Introduction
Thank you for choosing MG478/AC8700 CDMA2000 1X EV-DO Wireless Data Terminal
(hereinafter referred to as Data Terminal) of ZTE Corporation.
The Data Terminal equips with a standard USB interface and supports both CDMA2000 1X
EV-DO and CDMA2000 1X network. In the area where there is signal, it allows you to go surfing
on the Internet, browse the web pages, and send & receive Emails
2. Specification
Model
Parameter
MG478 AC8700
Transmitting Frequency
452.625-456.850MHz 824-849MHz
Receiving Frequency
462.625-466.850MHz 869-894MHz
Stability Fc±300Hz
Dimensions (
L
×
W
×H)
80 mm ×36 mm×12.8mm
Weight 38.7g
Data Rate Max. down-link transmission rate: 2.4Mbps,
Max. up-link transmission rate: 153Kbps
Current 5V˄using USB interface supply˅
Current Consumption Sleep: 5mA Max.: 480mA
Transmitting Power
224mW
3. Precautions
¾Please don’t use the product near flammable or explosive materials because it might cause
failure or fire.
¾Keep the product away from high temperature, humidity, or dust because it might cause
failure.
¾Avoid shock, cast or impact. Please keep the product well when you don’t use it.
¾Do not dismantle or disassemble the product at will or revolve the antenna frequently. Our
company will not provide warranty service for the damage caused by abnormal operations.
¾Don’t use the product near the place where is weak signal or high-precision electronic device
because the magnetic interference might cause the misoperation of electronic device or other
problems.
¾Please don’t insert or pull out the card with great force to avoid damaging the interface.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
ZTE Corporation http//wwwztecomcn
4. Appearance
4.1 Introduction
Top View Rear View
LED status descriptions:
Network Registered There is service or
searching the network LED Insert the data terminal
EV-DO 1X EV-DO 1X
Yellow ON OFF Slow Flash OFF Quick Flash
Green ON Slow Flash OFF Quick Flash OFF
USB Interface
Host
Tap
Antenna
LED
R-UIM Card Cover
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
ZTE Corporation http//wwwztecomcn
4.2 Insert R-UIM Card
Note: If your data terminal doesn’t need R-UIM card, please skip this section.
1. Pull out the tap
2. Take out the R-UIM card cover in the
direction indicated by the arrow 3. Insert R-UIM card as below figure
4. Push back R-UIM card cover in the direction indicated by the arrow
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
ZTE Corporation http//wwwztecomcn
5. Install and Uninstall
System Requirements:
The Data Terminal supports the following operating system:
¾Windows 2000
¾Windows XP
PC minimum configurations:
CPU Pentium-II/233MHz
USB interface 2.0 (USB1.0 and 1.1 compatible
Optical Drive CD-ROM (for installation only)
Memory 64 MB
Disk Space 30 MB (used for installation of application)
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
ZTE Corporation http//wwwztecomcn
5.1
Windows 2000
5.1.1 Install
Note:
Do not insert the Data Terminal before installation.
1ǃFind “Setup.exe” firstly in Data Terminal CD-ROM, double-click it to display the Welcome
picture, and then click “Next”;
2ǃSelect the location where you want the program to be installed, and then click “Next”;
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
ZTE Corporation http//wwwztecomcn
3ǃSelect Start Menu folder, and then click “Next”;
4ǃWhen you see the window below, please click “Install”;
5ǃPlease wait for installation.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
ZTE Corporation http//wwwztecomcn
6ǃPlease insert the Data Terminal into USB interface if the system prompts you to insert the
hardware (If it has been inserted, please unplug it and insert again.)
7ǃThe system shall find the new hardware and install the driver automatically. Just wait a minute;
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
ZTE Corporation http//wwwztecomcn
8ǃThe driver is installed successfully. Pleas click “OK”;
9ǃClick “Finish” to close the last screen of the wizard. Now you can start the application for Data
Terminal.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
ZTE Corporation http//wwwztecomcn
5.1.2 Uninstall
1ǃSelect Start -> Programs -> ZTE EV-DO -> Uninstall ZTE EV-DO. Click “Uninstall ZTE
EV-DO”, and you will be asked if you want to remove the program. Click “Yes”;
2ǃPlease wait;
3ǃClick “OK” when un-installation is completed;
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
ZTE Corporation http//wwwztecomcn
5.2
Windows XP
5.2.1 Install
Note:
Do not insert the Data Terminal before installation.
1ǃFind “Setup.exe” firstly in the Data Terminal CD-ROM, double-click it to display the Welcome
picture, and then click “Next”;
2ǃSelect the location where you want the program to be installed, and then click “Next”;
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
ZTE Corporation http//wwwztecomcn
3ǃSelect Start Menu folder, and then click “Next”;
4ǃWhen you see the window below, please click “Install”;
5ǃPlease wait for installation. This process will take a few minute;
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
ZTE Corporation http//wwwztecomcn
6ǃPlease insert the Data Terminal into USB interface if the system prompts you to insert the
hardware (If it has been inserted, please unplug it and insert again.)
7ǃThe system shall find the new hardware and install the driver automatically. Just wait a
minute.(Please ignore the prompt during the installation, such as “USB device not recognized” or
“Your hardware might not be able to work normally because there is an error during the hardware
installation.”)
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
ZTE Corporation http//wwwztecomcn
8ǃThe driver is installed successfully. Pleas click “OK”;
9ǃClick “Finish” to close the last screen of the wizard. Now you can start the application for data
terminal
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
ZTE Corporation http//wwwztecomcn
5.2.2 Uninstall
1ǃSelect Start -> Programs -> ZTE EV-DO -> Uninstall ZTE EV-DO. Click “Uninstall ZTE
EV-DO”, and you will be asked if you want to remove the program. Click “Yes”;
2ǃPlease wait;
3ǃClick “OK” when un-installation is completed.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
ZTE Corporation http//wwwztecomcn
6. Run the Application
After the application is installed successfully, the application icon will appear on your
desktop. Double-click this icon or select from Start -> Programs -> ZTE EV-DO -> ZTE EV-DO.
Run the application to display the following user interface.
The icons on the interface are used to access the function, which indicate as below:
Connect/Disconnect Open URL
Connection Records Setting
Help
Status Bar:
EV-DO Indication
1X Indication
Signal strength indication. The more bars,
the stronger signals
CDMA network unavailable
Network Connection
Sleep mode
In Roaming
No R-UIM card inserted
R-UIM card inserted
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
ZTE Corporation http//wwwztecomcn
7. Connect/Disconnect
Connect
Click icon to set the relevant parameters. For details, please refer to Chapter 9
“Setting” for details;
Click icon at the left-up corner of the interface;
After connecting to Internet, the current network information will appear on the
interface. Double-click any place in the display area to view the connection records.
Disconnect
After connecting to Internet, click the rotating icon at the left-up corner of the interface.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
ZTE Corporation http//wwwztecomcn
8. Connection Records
Click icon to view connection records. Connection records save the previous relevant
information including Start at, Duration and Transmit bytes, which help you know the status
easily.
By switching among “List”, “Monthly” and “Statistic”, you could inquire the records every time,
by month or by time.
Note:
The relevant information contained in connection records are just for user’s reference rather than
the charging basis.
Delete Connection Records
Click “Delete” button to delete the records you have selected on the interface.
Clear Connection Records
Click “Clear” button to delete all the records.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
ZTE Corporation http//wwwztecomcn
9. Setting
Network Connection Setting
Click icon to set up the relevant parameters. After the setting, click “Apply”
button to save the settings on the current interface.
Click “Default” button and then “Apply” button to restore the settings on the current
interface to factory default.
Note:
The default network setup parameters are as below. Different regions may have different
network setup parameters, so please consult your local telecom operator.
Phone: #777
User: card
Password: card
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
ZTE Corporation http//wwwztecomcn
Other Setting:
Click “Options” to switch the interface, and you could set URL and select the skin,
language, etc. After that, click “Apply” button to save the settings on the current
interface .
Click “Default” button and then “Apply” button to restore the settings on the current
interface to factory default.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
ZTE Corporation http//wwwztecomcn
10. Help
Click button to view the help file.
Click “Help” button to view the relevant help file; click “Online service” to enter our
company’s website.
You could view the software and its version information under “About”.
11. Connect to the Website
Click button to directly connect the website you set. For details on the website setting,
please refer to Chapter 9 “Setting”.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
ZTE Corporation http//wwwztecomcn
12. Trouble-shooting
After the installation, go to device manager and find “ZTE Status Interface 3197” under “Modem”
and “ZTE USB Modem 3197” under “Port”. If they are not found, please remove the software and
reinstall.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
ZTE Corporation http//wwwztecomcn
Common Failures Table:
Failures Causes Solutions
Error occurs when running
setup.exe file. The setup file may be damaged.
Please download the program on
our website WWW.ZTEIT.COM
and reinstall it.
Directly run the software before the
Data Terminal is plugged in.
Close the software, plug in the Data
Terminal and run it again.
Open port failed. The port is occupied by other
applications, such as “Hyper terminal”,
or the software is already run.
Close relevant software and run the
software again.
R-UIM card is not inserted. Insert R-UIM card.
R-UIM card isnÿt inserted properly.
Sometimes the front side and back side
are confused.
Please refer to section 4.2. Properly
insert R-UIM card.
No R-UIM card.
R-UIM card is damaged. Validate by
using a CDMA terminal.
Replace R-UIM card.
Antenna is not connected to the Access
Box.
Insert the antenna into the Data
Terminal.
Out of the network service area. Make sure it is in the CDMA
network service area.
No signal indicated.
The antenna or RF component is
damaged.
Replace relevant damaged parts.
Wrong setting of parameters (Phone,
User, Password)
Correct the parameter settings.
Consult your service provider for
details.
Not enough money in R-UIM card. Consult your service provider for
details.
Dialing failed
Network congestion or failure. Try again later.
The Data Terminal is being connected.
(It usually occurs when the Internet
connection is immediately made after
the call is dialed)
Reconnect.
Internet connection failure.
Poor network signal. View signal strength indication and
check if the antenna is properly
inserted.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
ZTE Corporation http//wwwztecomcn
If the problems cannot be solved after the above handling, please call 86-755-2601555 or feed
back your information directly by sending emails to zte_mobile@zte.com.cn for customer service.
We will reply to you as soon as possible and provide you with high quality after-sales services.
*SAR Information
The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types AC8700
(FCC ID: Q78-AC8700) has also been tested against this SAR limit. The highest SAR value reported
under this standard during product certification for use when properly worn on the body is 0.271 W/kg.