Zebex BRC-RS90 Bluetooth communication cradle User Manual
Zebex Industries Inc Bluetooth communication cradle
Zebex >
user manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1723737 |
| Application ID | UQLi4nzDKqvnKihN+wFe+g== |
| Document Description | user manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 100.33kB (1254093 bits) |
| Date Submitted | 2012-06-15 00:00:00 |
| Date Available | 2012-06-15 00:00:00 |
| Creation Date | 2012-06-13 16:54:25 |
| Producing Software | Acrobat Distiller 10.1.3 (Windows) |
| Document Lastmod | 2012-06-13 16:54:25 |
| Document Title | user manual |
| Document Creator | Acrobat PDFMaker 9.1 for Word |
| Document Author: | martine.mo |
Advanced Handheld High-Speed Laser Scanner This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2)This device must accept any interference received, including interference that may cause undesired operation. 15.105 Federal Communications Commission (FCC) Requirements, Part 15 This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ---Reorient or relocate the receiving antenna. ---Increase the separation between the equipment and receiver. ---Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ---Consult the dealer or an experienced radio/TV technician for help. USER’S MANUAL User’s Manual Z-3190BT, Z-3191BT, Z3192BT Wireless Barcode Scanner CR-90, RS-90 Charging & RF Communication Station Revision History Changes to the original manual are listed below: Version 1.0 1.1 1.2 Date August. 24, 2011 March. 26, 2012 April. 18, 2012 1.3 1.4 May. 24, 2012 June. 1 2012 Wireless Handheld Gun Type Scanner Description of Version Initial release Added wireless communication tips Added cable clip installation and Smart Phone Software Keypad Control Setting Added pin-out configuration and cable pin-out Removed the charging cradle section USER’S MANUAL Important Notice No warranty of any kind is made in regard to this material, including, but not limited to, implied warranties of merchantability or fitness for any particular purpose. We are not liable for any errors contained herein nor for incidental or consequential damages in connection with furnishing, performance or use of this material. We shall be under no liability in respect of any defect arising from fair wear and tear, willful damage, negligence, abnormal working conditions, failure to follow the instructions and warnings, or misuse or alteration or repair of the products without written approval. No part of this document may be reproduced, transmitted, stored in a retrieval system, transcribed, or translated into any human or computer or other language in any form or by any means electronic, mechanical, magnetic, optical, chemical, biological, manual or otherwise, except for brief passages which may be quoted for purposes of scholastic or literary review, without express written consent and authorization. We reserve the right to make changes in product design without reservation and without notification. The material in this guide is for information only and is subject to change without notice. All trademarks mentioned herein, registered or otherwise, are the properties of their various, ill, assorted owners. General Handling Precautions Do not dispose the scanner in fire. Do not put the scanner directly in the sun or by any heat source. Do not use or store the scanner in a very humid place. Do not drop the scanner or allow it to collide violently with other objects. Do not take the scanner apart without authorization Guidance for Printing This manual is in A5 size. Please double check your printer setting before printing it out. When the barcodes are to be printed out for programming, the use of a high-resolution laser printer is strongly suggested for the best scan result. Copyright © 2012. All rights reserved. ii Wireless Handheld Gun Type Scanner USER’S MANUAL Radio Notice This equipment generates uses and can radiate radio frequency energy. If not installed and used in accordance with the instructions in this manual, it may cause interference to radio communications. The equipment has been tested and found to comply with the limits for a Class B computing device pursuant to EN55022 and 47 CFR, Part 2 and Part 15 of the FCC rules. These specifications are designed to provide reasonable protection against interference when operated in a commercial environment. Radio and Television Interference Operation of this equipment in a residential area can cause interference to radio or television reception. This can be determined by turning the equipment off and on. The user is encouraged to try to correct the interference by one or more of the following measures: - Reorient the receiving antenna. - Relocate the device with respect to the receiver. - Move the device away from the receiver. - Plug the device into a different outlet so that the device and the receiver are on different branch circuits. If necessary the user may consult the manufacturer, and authorized dealer, or experienced radio/television technician for additional suggestions. The user may find the following booklet prepared by the Federal Communications Commission helpful: “How to Identify and Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. Government Printing Office, Washington, DC 20402 U.S.A., Stock No. 004000003454. Laser Safety This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions in this manual, it may cause interference to radio communications. The equipment has been tested and found to comply with the limits for a Class B computing device pursuant to EN55022 and 47 CFR, Part 2 and Part 15 of FCC Rules. These specifications are designed to provide reasonable protection against interference when operated in a commercial environment. Radiant Energy: The laser scanner uses one low-power visible laser diodes operating at 650nm in an opto-mechanical scanner resulting in less than 3.9ʅW radiated power as observed through a 7mm aperture and averaged over 10 seconds. Do not attempt to remove the protective housing of the scanner, as unscanned laser light with a peak output up to 0.8mW would be accessible inside. Wireless Handheld Gun Type Scanner iii USER’S MANUAL Laser Light Viewing: The scan window is the only aperture through which laser light may be observed from this product. A failure of the scanner engine, while the laser diode continues to emit a laser beam, may cause emission levels to exceed those for safe operation. The scanner has safeguards to prevent this occurrence. If, however, a stationary laser beam is emitted, the failing scanner should be disconnected from its power source immediately. Adjustments: Do not attempt any adjustments or alteration of this product. Do not remove the protective housing of the scanner. There are no user-serviceable parts inside. Optical: The use of optical instruments with this product will increase the eye hazard. Optical instruments include binoculars, magnifying glasses, and microscopes but do not include normal eye glasses worn by the user. CAUTION: Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. For CE-Countries This scanner is in conformity with CE standards. Please note that an approved, CE-marked power supply unit should be used in order to maintain CE conformance. Power Supply iv Use only the type of battery and the charging equipments that came with your scanner. Using any other type of battery and charging equipment may damage the scanner and invalidate the warranty. Do not short the battery terminals. The battery could overheat. Do not attempt to split or peel the outer casing. Remove the battery if the scanner is not going to be used for a long time. If the battery is left unused for more than 3 months, you need to charge the battery before use. Wireless Handheld Gun Type Scanner USER’S MANUAL Wireless Communication Wireless technology operates 100M / 75M with communication cradle. Maximum communication range may vary depending on obstacles (person, metal, wall, etc.) or electromagnetic environment. The following conditions may affect the sensitivity of wireless communication. There is an obstacle such as a person, metal, or wall between this unit and wireless device. A device using 2.4 GHz frequency, such as a wireless LAN device, cordless telephone, or microwave oven, is in use near this unit. Because wireless devices and wireless LAN (IEEE802.11b/g) use the same frequency, microwave interference may occur and resulting in communication speed deterioration, noise, or invalid connection if this unit is used near a wireless LAN device. In such a case, perform the following. Use this unit at least 10 m (about 30 ft) away from the wireless LAN device. If this unit is used within 10 m (about 30 ft) of a wireless LAN device, turn off the wireless LAN device. Install this unit and wireless device as near to each other as possible. Microwaves emitting from a wireless device may affect the operation of electronic medical devices. Turn off this unit and other wireless devices in the following locations, as it may cause an accident. Where inflammable gas is present, in a hospital, train, airplane, or a petrol station Near automatic doors or a fire alarm This unit supports security capabilities that comply with the wireless standard to provide a secure connection when the wireless technology is used, but security may not be enough depending on the setting. Be careful when communicating using wireless technology. We do not take any responsibility for the leakage of information during wireless communication. Connection with all wireless devices cannot be guaranteed. A device featuring wireless function is required to conform to the wireless standard specified by wireless SIG, and be authenticated. Even if the connected device conforms to the above mentioned wireless standard, some devices may not be connected or work correctly, depending on the features or specifications of the device. Depending on the device to be connected, it may require some time to start communication. Tips to help improve your wireless network 1. Position the access point (host/cradle) in a relatively empty space at central location. When possible, place the access point in a central location on the high ground (1m or above). If your access point is against an outside wall, the signal will be weak on the other side of the room. Bad host placement Wireless Handheld Gun Type Scanner Good host placement USER’S MANUAL Table of Contents Important Notice..................................................................................................................ii General Handling Precautions..............................................................................ii Guidance for Printing ...........................................................................................ii Laser Safety .........................................................................................................iii For CE-Countries..................................................................................................iv Power Supply ......................................................................................................iv Wireless Communication .....................................................................................v Introduction .........................................................................................................................1 Product Overview ........................................................................................................2 Scanner ................................................................................................................2 Cradle ...................................................................................................................2 Scanner and Accessories..............................................................................................3 Battery Installation.......................................................................................................4 Installing Cable Clip ......................................................................................................5 Connecting the Cradle..................................................................................................7 Charging the Battery ....................................................................................................8 Power on the Scanner ..................................................................................................9 How to Scan ...............................................................................................................10 Radio Communication Host Type...............................................................................11 Cradle Host Mode ..............................................................................................11 SPP Mater/SPP Slave Mode................................................................................11 HID Mode ...........................................................................................................11 Paging the Scanner.....................................................................................................12 Scanner USB online to Host .......................................................................................12 USB Online Mode ...............................................................................................12 Visible Indicators ........................................................................................................13 Scanner ..............................................................................................................13 Cradle .................................................................................................................14 Sound Indicators ........................................................................................................14 ACK/NAK Protocol or Frame Packing..........................................................................15 Scanner to Remote Application..................................................................................16 Pin-out Configuration.................................................................................................18 Cable Pin-out..............................................................................................................19 Programming Guide ...........................................................................................................20 Connecting to a Host..................................................................................................24 Cradle Host Mode ..............................................................................................25 Wireless Mode ...................................................................................................26 Data Transnit Method ........................................................................................31 System Function Settings ...........................................................................................34 Data Editing ........................................................................................................80 Appendix 1: USB Virtual COM Driver Installation ..............................................88 Appendix 2: Barcode Length Setting ..................................................................89 Wireless Handheld Gun Type Scanner vii USER’S MANUAL Introduction This scanner is a gun type rugged wireless CCD/Laser barcode scanner with a state of the art scan engine. Featuring a superb scanning speed and able to withstand 1.5 meter drop, it is ideal for manufacturing and logistic sectors. The cradle, a dongle, or devices with wireless technology can be the host of this scanner. All scanned data are instantly transferred to the connected host in a 100meter connection range in open space or 75-meter range in indoor environments (the actual communication range may vary due to different indoor placement). This feature eliminates hazardous cables and creates a safer work environment. Either scanning in the handheld or hands-free mode, this scanner always offers a highaccuracy and reliable scanning ability. This scanner would be your trusted tool scanning partner. Key Features: Superb scanning ability Proprietary hardware decoding technology 100M long-range wireless connection Rugged and ergonomic form factor Flexible communications Wireless Handheld Gun Type Scanner USER’S MANUAL Product Overview Scanner LED Indicator Exit Window Buzzer Trigger Strap Hole Cable Connector Metal Charging Contacts Cradle Charging Contacts Function Trigger/LED indicator Host Connector DC Power Connector Bluetooth Address Label Wireless Handheld Gun Type Scanner USER’S MANUAL Scanner and Accessories The scanner package contains: Wireless scanner with battery / Scanner cradle (optional) (with cradle) (without cradle) Li-ion battery pack Communication cable for cradle (optional) Mini USB B to mini USB A cable 5V USB Power adapter CD-ROM or handbook (Containing manual and programming guide) Cable clip If any contents are damaged or missing, please contact your dealer immediately. Wireless Handheld Gun Type Scanner USER’S MANUAL Battery Installation Installing Batteries The rechargeable batteries are packed individually for shipping safety. Please follow the steps below to install the batteries. Always use the rechargeable batteries provided by the manufacturer to avoid any non-compatible danger or void the warranty. 1. Unscrew the cap from the battery compartment at the bottom of the scanner and insert the battery. 2. Make sure the red tag on the battery is tugged in and not blocking the cable connector and close the cap. 3. Tighten the screw on the cap to secure the battery. Wireless Handheld Gun Type Scanner USER’S MANUAL Installing Cable Clip Cable clip is used to hold the mini USB cable in USB Online Mode. With the cable clip, you can easily transform your wireless scanner into a wired one. Attaching Cable Clip 1. Insert the cable clip to the strap hole as shown. 2. Gently turn the cable clip counter-clockwise and push the cable clip all the way through the strap hole. 3. Attach the bottom part of the cable clip to the scanner handle. 4. Insert the USB cable as illustrated below. Wireless Handheld Gun Type Scanner USER’S MANUAL Removing Cable Clip 1. Detach the cable from the clip and detach the bottom part of the cable clip from the scanner handle. 2. Unhook the left part of the cable clip from the strap hole then turn it clockwise. While in turning motion, push the cable clip all the way through. 3. Remove the cable clip from the strap hole. Wireless Handheld Gun Type Scanner USER’S MANUAL Connecting the Cradle The cradle host features wireless technology and is designed to support radio communication to the scanner. It can be used for both battery charging and radio communication. 1. Take the desirable interface cable and insert the RJ-45 connector on the bottom of the cradle. You will hear a clear and short “click” sound; then connect the other end to the host. 2. Connect the included USB cable to mini USB port at the bottom of the cradle and connect other end to USB power adaptor. 3. Connect the USB power adaptor into AC outlet. The LED indicator on the cradle should flash blue until it made connection with the scanner. Communication cable Mini USB B to USB power adaptor only When using Keyboard wedge and USB interface for cradle communication, it is not necessary to have an external power adapter if host has sufficient power. But these interfaces need external power adapter when charging batteries. The mini USB port on the bottom of the cradle should only be connected using the USB power adaptor. Please do not connect the USB cable to a PC host for charging when using the cradle. Wireless Handheld Gun Type Scanner USER’S MANUAL Charging the Battery The scanner offers two different ways to charge the battery: USB Cable or Cradle. To charge the battery using the cradle: 1. Connect the cradle. Please see Connecting the Cradle section for more details. 2. Place the scanner on the cradle. You will hear a short beep sound from the scanner indicating scanner is in contact with the cradle. 3. The battery begins charging when the scanner LED indicator starts flashing green. LED turns steady green when charging is complete. Approx. charging time: 4.5 hours To charge the battery using the USB cable: There are two method to charge scanner via USB cable. Host USB Power Power adaptor 1. Connect the mini USB connector directly to the scanner. 2. Connect the other end of the USB connector to the host to begin charging. You can also connect the USB cable to an outlet using the power adapter to charge the battery. 3. The battery begins charging when the scanner LED indicator starts flashing green. LED turns steady green when charging is complete. Wireless Handheld Gun Type Scanner USER’S MANUAL Approx. charging time: 5~6 hours The scanner will power on automatically when charging. Batteries shipped may not be full charged and should be fully charged for maximum charge capacity. Recommended charging environment is temperature in 0̓C~35̓C (32̓ʳ ʳ ʳ F~95̓F). Power on the Scanner 1. Ensure the battery is fully charged. Please refer to the previous section to charge the battery. 2. Press and hold the trigger for 1 second until a long beep sound is heard to turn on the scanner. Wireless Handheld Gun Type Scanner USER’S MANUAL How to Scan There are two ways to scan with this device. Handheld scanning Presentation scanning Handheld scanning 1. Power on the scanner. 2. Press the trigger and aim at the barcode as illustrated. 3. When decoding is successful, the scanner beeps and the LED indicates blue. Presentation Scanning 10 1. Put the scanner into the cradle for presentation scanning. 2. Move the barcode label approach the scanner scanning zone. 3. When decoding is successful, the scanner beeps and the LED indicates blue. Wireless Handheld Gun Type Scanner USER’S MANUAL Radio Communication Host Type This scanner support three radio communication types: Cradle Host mode SPP master/slave mode HID mode Cradle Host Mode The scanner communicates with the host through the cradle and the cradle communicates directly to the host via host interface cable connection. Typically, scanner and cradle in the same delivery box are paired in factory. As soon as both are powered on, they should find and connect to each other immediately. However, under special circumstance that the scanner and the cradle are not paired with the cradle, please See Cradle Host Pairing for detail operation information. SPP Mater/SPP Slave Mode The scanner communicates with the host through wireless connection. Please see Wireless Mode for detail operation information. HID Mode The scanner communicates with the smart phone through wireless HID connection. Please see BT HID mode for detail operation information Wireless Handheld Gun Type Scanner 11 USER’S MANUAL Paging the Scanner 1. Ensure the cradle is properly connected to the host and LED indicator is showing steady blue. 2. Press the function trigger on the cradle. You should hear the scanner make 3 beep sounds and blue LED flash 3 times if it is in range. Scanner USB online to Host The scanner provides other ways for you to connect to the host. When the radio communication is not available, the scanner can be connected to transmit data via USB Online mode. Please see USB Online Mode for detail operation information. USB Online Mode The scanner connects directly to a USB host to recharge and transmit data. 12 Wireless Handheld Gun Type Scanner USER’S MANUAL Visible Indicators Scanner There are 2 groups of LED indicators on top of the scanner. These indicate the operational status of the scanner. Group 2 Group 1 LED Status Group_ 2 Group_1 Blue Flashing Blue fast Flashing Blue Slow Flashing 1 Blue Flashing Blue Fast Flashing Green Flashing Steady Green Steady Red Red flashing slow (with continuous beep sound) Red flash twice (with 2 beep sound) Wireless Handheld Gun Type Scanner Indication Waiting for radio connection (flash time 0.5s : 0.5s). Radio connecting. Device connected (flash time 0.03s : 3s). A barcode was decoded successfully Data transmission Charging mode Battery fully charged Programming mode Low battery warning Very low battery warning 13 USER’S MANUAL Cradle Cradle LED LED Status Red steady and blue continuous flashing Steady red and blue Red and blue interchange Steady blue Blue flashing Indication Cradle is radio disconnected and power from DC adaptor is lost. Cradle is radio connected. But lost DC power from the adaptor. USB Interface communication failed. Cradle is radio connected. Cradle is radio disconnected. Sound Indicators When the scanner is in operation, it provides audible feedback. The beeps indicate the status of the scanner. Beep A long beep One beep Indication Power on scanner. A barcode has been successfully decoded and data is either transfer to the host or saved in the memory. Scan cradle pair barcode. Data communication failed or out of range. Low battery warning. 1 high - low - high beeps Four short medium beeps Intermission medium-low beeps 1 short medium – low beeps Scanner is power down. 1 long high – medium beeps Enter programming mode. 1 long medium - medium Exit Programming mode. beeps 14 Wireless Handheld Gun Type Scanner USER’S MANUAL ACK/NAK Protocol or Frame Packing When scanner is in SPP Master/Slave mode, and add in the data protocol or packing could confirm the data reliability. Refer to below for different setting options: a) No ACK/NAK protocol: data BT Scanner b) Remote BT device ACK/NAK only data BT scanner NAK Remote BT Resend device ACK Get a good beep c) Frame packing: Data format of BT scanner Acknowledge Remote BT device Get a good beep Wireless Handheld Gun Type Scanner 15 USER’S MANUAL Scanner to Remote Application Data Format of Packet To send a data (barcode) to the remote application, the BT scanner has to encapsulate it: EAH (Header) Size of payload 1 byte 1 byte FEH (Format Byte) 1 byte Data ID Data Barcode Type 1 byte Varies 1 byte AEH (End of Byte) 1 byte Reserved Byte 1 byte Title Header Character (EAH) Definition The character ID at the head of every data. It has to start with EAH. Size of Payload The encapsulated data length excluding header character. Differentiate data format; barcode data is always FEH. Format Byte (FEH) Data ID The number of each data. If receive the same ID more than once, only the first one is valid, delete the rest. Barcode Type (1 byte) Please refer to the Barcode Type Table. Data Decoded barcode data. End of Byte (AEH) Record data ends. Reserved Byte Reserved for future use. Example: If Code39 barcode data is "ABCD", than sender sends out: EAH + 0AH + FEH + ID + "ABCD "+ 11H+AEH + Reserved Byte 0AH = 1+1+1+4+1+1+1 Acknowledge packet 55H (Header ) 1 byte Data ID 1 byte 55H (end of byte) 1 byte Example: If scanner sends out: EAH , 0AH , FEH , 01H , "ABCD ", 011H, AEH , EEH Remote acknowledges: 55H +01H + 55H 16 Wireless Handheld Gun Type Scanner USER’S MANUAL Barcode Type Table Code Value Code39 0x11 Codabar 0x01 Code128 0x03 Interleaved 2/5 0x02 Code93 0x06 UPC-E 0x14 UPC-A 0x24 EAN-8 0x34 EAN-13 0x44 Chinese Post Code 0x05 MSI 0x07 Wireless Handheld Gun Type Scanner 17 USER’S MANUAL Pin-out Configuration Scanner mini USB Pin-Out Configuration PIN 1. +5V PIN 2. USB_D- PIN 3. USB_D+ PIN 4. NC PIN 5. GND Cradle Phone Jack Pin-Out Configuration RJ 1. RTS_EIA RJ 6. RX_ EIA RJ 2. KB Data / USB_D+ RJ 7. KB Clock RJ 3. PC Clock / USB_D- RJ 8. +5V RJ 4. GND RJ 9. PC Data RJ 5. CTS_ EIA RJ10. TX_ EIA Cradle Mini USB Pin-Out Configuration PIN 1. DC+5V PIN 2. NC PIN 3. NC PIN 4. NC PIN 5. GND 18 Wireless Handheld Gun Type Scanner USER’S MANUAL Cable Pin-out 1. Keyboard Wedge Cable (for PS/2) PIN-OUT CONFIGURATION MINI DIN (M) MINI DIN(F) DIN FUNCTION DIN FUNCTION 1. PC Data 1. KB Data 2. N.C. 2. N.C. 3. GND 3. GND 4. +5V 4. +5V 5. PC Clock 5. KB Clock 6. N.C. 6. N.C. 2. RS-232 Cable (DTE pin out) PIN-OUT CONFIGURATION DB-9 (F) FUNCTION TX RX CTS RTS GND +5V 3. RS-232 Cable (DCE pin out) PIN-OUT CONFIGURATION DB-9 (F) FUNCTION RX TX CTS RTS GND +5V 4. USB / Virtual COM USB / OPOS USB Interface with Detachable Cable Type A USB TYPE A FUNCTION CONNECTOR 1. VCC 2. D3. D+ 4. VSS Wireless Handheld Gun Type Scanner 19 USER’S MANUAL Programming Guide Program Procedure Using Barcode Manual 1. Power up the scanner. 2. Scan the Start of Configuration barcode. 3. Scan the barcode for the desired feature. Multiple features can be enabled/disabled before scanning the End of Configuration barcode. 4. Scan the End of Configuration barcode and save the new configuration. 5. To give up a configuration change, power off the scanner before scanning the End of Configuration barcode or scan the Abort barcode. 6. For some parameter setting, such as barcode length and identifier code, it is required to scan the Set barcode to save the configuration. Power up the scanner Scan the “Start of Configuration” barcode Scan barcode of the desired feature Scan the “End of Configuration” barcode Finish the configuration 20 Scan the “Abort” barcode Power off the scanner Discard the configuration Wireless Handheld Gun Type Scanner USER’S MANUAL Default Parameters The factory default setting table gives the default settings of all the programmable parameters. The default settings will be restored whenever the "Reset" programming label is scanned and the scanner is in programming mode. Default values are highlighted in grey background in the settings. Factory Default Setting Parameter Radio communication Wireless host Pairing mode Data transmit Radio protocol timeout Power off timeout Encryption Cradle Host RS-232 communication Baud rate Parity Data bits Stop bit RTS/CTS Terminator Keyboard Wedge Communication Terminator Keyboard Terminator USB Communication Terminator Code mode Keyboard Wand Emulation Wand emulation speed Data output Pair contact on cradle Scanner Decoder Selection Wireless Handheld Gun Type Scanner Default Cradle Host Unlocked Normal 5 seconds 20 minutes Enable 9600 none offPC/AT US keyboard Enter(Alpha numeric) Enter Scan code US keyboard Normal Black=high Enable Default 21 USER’S MANUAL 22 EAN/UPC CODE 39 Code 32 CODABAR ITF 2 OF 5 MSI Chinese post code Code 93 Code 128 EAN-128 Enable Enable Disable Enable Enable Disable Disable Enable Enable Disable Telepen Code 11 Standard 2 of 5 Industrial 2 of 5 GS1 DataBar Disable Disable Disable Disable Disable Beeper Sound Frequency Duration Operating Parameter Scan mode Stand mode Header and trailer Inter-message delay Inter-character delay Code Identifiers Identifier code as ZEBEX standard Identifier code as AIM standard Code 39 identifier code ITF 2 of 5 identifier code Chinese post code identifier code UPC-A identifier code UPC-E identifier code EAN-13 identifier code EAN-8 identifier code Codabar identifier code Code 128 identifier code Code 93 identifier code Default Medium Medium Default Trigger mode Enable None None None Default Disable Disable FF Wireless Handheld Gun Type Scanner USER’S MANUAL MSI identifier code Code 11 identifier code Standard 2 of 5 identifier code Industrial 2 of 5 identifier code GS1 DataBar identifier code GS1 DataBar Limited identifier code GS1 DataBar Expanded identifier code RS RL RX Default Data Transmit Format Code EAN-13 EAN-8 UPCA UPCE CODE128 EAN128 CODE39 CODABAR INTERLEAVED 2/5 CHINESE POST CODE CODE93 MSI Message format D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D1 D2 D3 D4 D5 D6 D7 D8 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D1 D2 D3 D4 D5 D6 D7 D8 D1-Dx (default 3~62) C1 D1-Dx (default 3~62) D1-Dx (default 3~62) D1-Dx (default 6~32) D1-Dx (default 6~32) D1-Dx (default 8~32) D1-Dx (default 3~32) D1-Dx (default 6~32) Wireless Handheld Gun Type Scanner 23 USER’S MANUAL Connecting to a Host The scanner provides several data transmit methods to communicate with the host. User may select the method according to their preferences. Read this section to learn the setups for connecting to different hosts. Start Of Configuration USB Online Mode The scanner connects directly to a USB host to recharge and transmit data. You may enable or disable the functions using the following settings. Disable USB communication Disable USB communication. USB online scan disable Enable USB communication USB online scan enable Wireless connection as the primary communication option to the host. USB connection is only used when wireless is disconnected. Set USB as the primary connection USB online scan, Ignore radio communication USB connection as the primary communication option to the host when it is available. Wireless mode is set as the secondary option. End Of Configuration 24 Wireless Handheld Gun Type Scanner USER’S MANUAL Start Of Configuration Cradle Host Mode The scanner communicates with the host through the cradle. Typically, scanner and cradle in the same delivery box are paired and corresponded to host interface in factory. To check if the scanner is paired to the cradle, check the scanner LED group1 for slow blue flash and check the top cradle LED for steady blue light. If LED group1 of scanner and top LED of cradle are both flashing blue, follow the steps below to radio connect the scanner and cradle. Cradle Host Pairing 1. See Connecting the Cradle to connect the cradle and the computer. Please make sure the cradle LED is flashing blue indicating it’s not linked to any scanner. If the LED shows steady blue, the cradle is already paired to another scanner so you must unpair the scanner before continuing. 2. Power on the scanner and enable cradle host mode if necessary. Enable cradle mode with this set. Cradle Host mode enable 3. Use the scanner to scan the pairing barcode at the bottom of the cradle to begin pairing. 3 short beeps will be heard. 4. The LED indicator on the scanner will flash blue rapidly indicating search mode in process. The LED on the cradle becomes steady blue when the pairing is successful. Scan the corresponding host interface the cradle is using to begin using the scanner. Return to cradle USB communication.ʳ (Communication cradle link required) Return to USB defaultʳ 5. Return to wand emulation default Return to RS232 default IBM PC/AT/PS/2 Keyboard emulation Return to cradle wand emulation. (Communication cradle link required) Return to RS232 cradle communication. (Communication cradle link required) Cradle IBM PC/AT/PS/2 Keyboard emulation. (Communication cradle link required) End Of Configuration Wireless Handheld Gun Type Scanner 25 USER’S MANUAL Start Of Configuration Wireless Mode The scanner connects to the host via wireless connection. You may select SPP Master or SPP Slave for PC connection or select HID mode and Smart phone mode for smart phone connection. SPP Slave Mode In this mode, the scanner connects to the host /PC via wireless connection and performs like there’s a serial connection. In SPP Slave mode, the scanner is discoverable from a remote device and it can request the scanner for connection. There are several ways to connect the wireless scanner to your PC. If you have your own applications please check their User’s Manuals for pairing instructions. To connect a wireless device to Window based system for the first time: 1. Turn on the host computer and activate its wireless connection. 2. Select “Add wireless device”. Or open the dialog BT devices and click “Add”. 3. Power on the scanner and program it with “SPP Slave mode” label. Enable wireless SPP Slave mode. Scanner SPP Slave enable 4. On Devices tab, click Add. This will open the Add wireless Device Wizard. 5. Select the "My device is set up and ready to be found" checkbox, and then click Next. 6. The scanner should be on the list of discoverable devices. The default name of the scanner is “ZBBT”. Select “ZBBT” and click “Next”. 7. Select “Let me choose my own passkey” and enter the pin code. The default pin code is “12345678. 8. Click “Next” to connect the scanner to the host. A short beep should be heard upon connection. End Of Configuration 26 Wireless Handheld Gun Type Scanner USER’S MANUAL Start Of Configuration SPP Master Mode In this mode, the scanner connects to the host /PC via wireless connection and performs like there’s a serial connection. In master mode, the scanner initiates the connection to the remote deviceˁ 1. Power on of the remote device and have its address ready in hand and make it discoverable. 2. Program the scanner with the “SPP Master enable” barcode. Enable SPP Master mode. Scanner SPP Master enable 3. Scan “Set wireless address” to set the address. Set wireless address (SPP Master only) Set wireless address for SPP Master connection. 4. Use the ASCII table in Programming Guide to input the 12 digit wireless address. For example: if the address is “011B1345600”, scan “0”, “0”, “1”, “1”, “B”, “1”, “3”, “4”, “5”, “6”, “0”, “0” from ASCII barcode labels. 5. Scan “Confirm Setting” to store the address. Confirm Setting (for address and pin code setting required) 6. Setup and input the pin code if necessary. Please see Setting Pin Code section for more details. 7. Scan “Required Pair with slave (SPP Master)” to begin pairing. Required Pair with slave (SPP Master) In SPP Master mode, you can print out a Code39 label of the wireless address in “BxxxxxxxxxxxxT” format and scan it with the scanner instead of using the ASCII table. End Of Configuration Wireless Handheld Gun Type Scanner 27 USER’S MANUAL Start Of Configuration BT HID mode In BT HID mode, the scanner connects to the host /PC via wireless connection and performs like there’s a keyboard connection. The scanner initiates the connection to the remote deviceˁ 1. Power on the scanner and program it with “BT HID Mode”. To connect a smart mobile phone (for example, iPhone, Android), the Smart phone mode must also be enabled. Enable wireless HID keyboard emulation BT HID mode Smart phone mode For smart phone mode (BT HID MODE must also be enabled). 2. Enable wireless connection on your host and follow the instructions in your host to set it to discover other wireless devices in its surrounding. 3. The scanner should be on the list of discoverable devices. The default name of the scanner is “ZBBT”. You will be prompt to enter paring pin code. Select “ZBBT” and input the pin code that appears on your mobile device to connect scanner to the phone. Scan the Enter barcode to confirm. A short beep should be heard upon connection. 4. Enter Full ASCII ---CR Function key-----“Enetr(num.)” End Of Configuration 28 Wireless Handheld Gun Type Scanner USER’S MANUAL Start Of Configuration Setting Pin Code 1. To change the pin code, use the “Set pin code” setting. Default is “12345678”. 2. Use the ASCII table in Programming Guide to input the new code (must be at least 4 digits and not more than 8 numeric digits). 3. Scan “Save Setting” to store the pin code. Set pin code (SPP Master only) Set pin code Confirm Setting (for address and pin code setting required) Please check the User’s Manual from your PC for wireless address and pin code. Deleting pin code To delete pin code, use the “Delete pin code setting”. Delete the stored pin code. Delete pin code Reset Name To change the scanner name back to the default name “ZBBT” use the “Default device name” setting. Change device name back to default “ZBBT”. Default device name End Of Configuration Wireless Handheld Gun Type Scanner 29 USER’S MANUAL Start Of Configuration Setting Name 1. To change the name displayed when the scanner is discovered, scan the “Friendly device name set” label. Default name is “ZBBT”. 2. Use the ASCII table in Programming Guide to input the name (Max.12 digits). 3. Scan “Confirm Setting” to store the new name. Friendly device name set Change the display name when scanner is discovered. Confirm Setting (for address and pin code setting required) Wireless Discovery Use the following settings to show or hide the device from wireless discovery. Make scanner visible to wireless device. Discover enable Make scanner invisible to wireless device. Discover disable End Of Configuration 30 Wireless Handheld Gun Type Scanner USER’S MANUAL Start Of Configuration Data Transnit Method The data transfer method includes three types: Normal (default), Out-of-Range Mode, and Batch Mode. Users may modify this setting according to their preferences. Normal When the scanner is within the connection range, the scanned data will be transferred to the host computer immediately. If the scanner is out of its connecting range, the scanner does not send or store any data. Batch mode is disabled. Data transmit normal Out of Range Scanned data are stored when scanner is out of its wireless communication range. When scanner is back into its communication range or re-connected, the stored data are sent when scanning next barcode label. Enable out of range mode. Out of range buffer enable End Of Configuration Wireless Handheld Gun Type Scanner 31 USER’S MANUAL Start Of Configuration Batch Mode Whether within the connection range or not, in batch mode, the scanner stores all scanned data that will be transferred to the host computer after scanning “Send Batch Data” label. Number of storable bar codes = 61,365 bytes of memory / (number of characters in the bar code +2) Batch mode Note: Scanner LED indicator will not flash while waiting for connection in this mode. Clearing Batch Use the settings in this section to clear the stored data. Clear batch data after send Clear batch data by scanning “Delete batch data” label Saved data are cleared after they are transferred to the host. Scan this label then scan “Save Setting” to delete the stored batch data. Same as previous setting but with alert sound. Delete batch data Confirm Setting (for address and pin code setting required) End Of Configuration 32 Wireless Handheld Gun Type Scanner USER’S MANUAL Start Of Configuration Batch Transfer Use the settings in this section to setup batch transfer. Send Batch Data By Scanning Label Send Batch Data on line USB cable contact Send Batch data on cradle Scanning this label automatically exits you from the Programming Mode. Press and hold the trigger for over 1 second to send the data. Data is ready to be transferred upon USB connection. Press and hold the trigger for over 1 second to send the data. Data is ready to be transferred upon placement on the cradle. Press and hold the trigger for over 1 second to send the data.(Cradle radio connected is required) Batch Mode Sounds Settings Use the settings in this section to setup the sound. Out of range resend data with beeper sound Add beeper sound when resending data in Out of range mode. No beeper sound when resending data Out of range resend data without beeper sound in Out of range mode. Send Batch Data without beep Send Batch Data with Beep No beep when sending data. Good-read LED will light up until the transfer is done. Beep sound when sending data. Good-read LED will light up until the transfer is done. End Of Configuration Wireless Handheld Gun Type Scanner 33 USER’S MANUAL System Function Settings Default values are highlighted in grey background. Start Of Configuration Barcode Value Description Return scanner to factory defaults Return cradle host to factory defaults Return to USB default (Communication cradle link required) Return to wand emulation default (Communication cradle link required) Return to RS232 default (Communication cradle link required) IBM PC/AT/PS/2 keyboard emulation (Communication cradle link required) Return as USB-virtual COM port default Return to stand-alone keyboard default Return as OPOS port default End Of Configuration 34 Wireless Handheld Gun Type Scanner USER’S MANUAL Start Of Configuration Barcode Value Description Display firmware version Abort (exit programming mode without any updates) Scan Mode Trigger mode The scanner becomes inactive as soon as the data is transmitted. It must be triggered to become active again. Auto scan mode The scanner is still active after the data is transmitted but the successive transmission of the same barcode is not allowed when the trigger switch is pressed again. Alternate mode The scanner illumination alternates between on and off when the trigger switch is pressed. Presentation mode Also called auto trigger mode. The scanner is inactive but will automatically detect barcodes presented in the scan zone and become active. Idle mode enable Idle mode disable Disable Idle mode. End Of Configuration Wireless Handheld Gun Type Scanner 35 USER’S MANUAL Start Of Configuration Radio Communication Setting Cradle Host mode Cradle Host mode enable Enable cradle mode with this setup. Unlock pairing mode In this mode, the scanner can pair with another cradle when disconnected. Lock pairing mode. In this mode, the scanner can not pair with another cradle. Undo pairing Undo the pairing between the cradle and the scanner. Scanner On Cradle sound alert enable Enable beep sound alert when scanner is placed on cradle. Scanner On Cradle sound alert disable Disable beep sound alert when scanner is placed on cradle. On Cradle Auto-Scan mode enable Enable Auto-Scan when scanner is placed on cradle. On Cradle Auto-Scan mode disable Disable Auto-Scan when scanner is placed on cradle. End Of Configuration 36 Wireless Handheld Gun Type Scanner USER’S MANUAL Start Of Configuration USB Online mode USB online scan disable USB online scan enable USB online scan, Ignore radio communication BT HID mode BT HID mode (Combo keyboard) For Apple mode (Must execute BT HID mode first) SPP Master/Slave mode Scanner SPP Master enable SPP Master (Connect wireless address “BxxxxxxxxxxxxT” in CODE39 format) Scanner SPP Slave enable Setting wireless address (SPP Master only) Set PIN code (SPP Master only) End Of Configuration Wireless Handheld Gun Type Scanner 37 USER’S MANUAL Start Of Configuration Default Device name Friendly device name set Delete pin code Confirm Setting (for address, device name, and pin code setting required) Required Pair with slave (SPP Master) Discover enable Discover disable Encryption enable Encryption disable Data communication without protocol Data communication with ACK/NAK protocol Data communication with Packing protocol End Of Configuration 38 Wireless Handheld Gun Type Scanner USER’S MANUAL Start Of Configuration Data Transmit Mode Data transmit normal Out of range buffer enable Batch mode Send Batch Data By Scanning Label Clear batch data after send Clear batch data by scanning “Delete batch data” label Delete batch data Send Batch Data on line USB cable contact. Send Batch data on cradle Out of range resend data with beeper sound Out of range resend data without beeper sound Send Batch Data without Beep Send Batch Data with Beep End Of Configuration Wireless Handheld Gun Type Scanner 39 USER’S MANUAL Start Of Configuration Radio protocol communication parameter Radio protocol timeout= 3 sec Radio protocol timeout= 5 sec Radio protocol timeout =8 sec Radio protocol timeout= 10 sec Radio protocol timeout =13 sec Radio protocol timeout =16 sec Radio protocol timeout= 20 sec End Of Configuration 40 Wireless Handheld Gun Type Scanner USER’S MANUAL Start Of Configuration Power off timeout parameter Power off timeout=5 min Power off timeout=10 min Power off timeout=20 min Power off timeout=30 min Power off timeout=1 hr Power Off timeout : 2 hr Power Off timeout : 4 hr Power Off timeout : 6 hr Power Off timeout : 8 hr End Of Configuration Wireless Handheld Gun Type Scanner 41 USER’S MANUAL Start Of Configuration Power Always On Power off by scanning this label Link beeper enable Link beeper disable Power-up beeper enable Power-up beeper disable Same Code Delay 50 msec 100 msec 200 msec 300 msec End Of Configuration 42 Wireless Handheld Gun Type Scanner USER’S MANUAL Start Of Configuration 400 msec 500 msec 600 msec 700 msec 800 msec 1000 msec Infinite End Of Configuration Wireless Handheld Gun Type Scanner 43 USER’S MANUAL Start Of Configuration Operation Function Setting Good Read Beeper Tone Selection Medium beeper tone High beeper tone Low beeper tone Speaker disable End Of Configuration 44 Wireless Handheld Gun Type Scanner USER’S MANUAL Start Of Configuration Beeper duration Selection Long Medium Short Ultra Short Ultra Long End Of Configuration Wireless Handheld Gun Type Scanner 45 USER’S MANUAL Start Of Configuration Vibration Parameter (Optional function, available only for customers of special request ) Good read vibrator enable. Good read vibrator disable Good read beeper and vibrator enable Vibration duration=100msec Vibration duration=200msec Vibration duration=300msec Vibration duration=400msec Vibration duration=500msec Vibration duration=1 second Vibration duration=2 second Vibration duration=3 second Vibration duration=4 second Vibration duration=5 second End Of Configuration 46 Wireless Handheld Gun Type Scanner USER’S MANUAL Start Of Configuration Inter Character Delay 0 ms 2 ms 5 ms 10 ms 20 ms 50 ms Inter Message Delay 0 ms 100 ms 500 ms 1000 ms End Of Configuration Wireless Handheld Gun Type Scanner 47 USER’S MANUAL Start Of Configuration Interface Settings 1. RS-232C Interface Setting Baud Rate 115200 19200 9600 4800 2400 1200 Parity Bit Even parity Odd parity Mark parity Space parity None parity Stop Bit 1 stop bit 2 stop bit Data Bit 7 data bit 8 data bit End Of Configuration 48 Wireless Handheld Gun Type Scanner USER’S MANUAL Start Of Configuration Handshaking Protocol None handshaking ACK/NAK Xon/Xoff RTS/CTS Enable BEEPER ON CHARACTER Ignore Beep on character ACK/NAK response time 300ms ACK/NAK response time 2 sec ACK/NAK response time 500 ms ACK/NAK response time 3 sec ACK/NAK response time 1 sec ACK/NAK response time 5 sec ACK/NAK response time infinity End Of Configuration Wireless Handheld Gun Type Scanner 49 USER’S MANUAL Start Of Configuration Message Terminator RS-232 message terminator—none RS-232 message terminator—CR/LF RS-232 message terminator—CR RS-232 message terminator—LF RS-232 message terminator—H tab RS-232 message terminator—STX/ETX RS-232 message terminator—EOT End Of Configuration 50 Wireless Handheld Gun Type Scanner USER’S MANUAL Start Of Configuration 2. Keyboard Wedge Setting Keyboard Wedge Setting IBM PC/AT/PS/2 Keyboard emulation International Keyboard mode ( ALT method) Keyboard language support---USA Keyboard language support---UK send scan code Keyboard language support---GERMANY Keyboard language support---FRENCH send scan code Keyboard language support---SPANISH send scan code Keyboard language support---ITALIAN send scan code Keyboard language support---Switzerland send scan code Keyboard language support---Belgium send scan code Keyboard language support---Japanese Capital lock on Capital lock off Function key emulation enable Function key emulation disable Send number as normal data Send number as keypad data End Of Configuration Wireless Handheld Gun Type Scanner 51 USER’S MANUAL Start Of Configuration Message Terminator Keyboard terminator---none Keyboard terminator---Enter Keyboard terminator---H-TAB End Of Configuration 52 Wireless Handheld Gun Type Scanner USER’S MANUAL Start Of Configuration 3. USB Interface Setting USB interface International Keyboard mode ( ALT method) Keyboard language support---USA Keyboard language support---GERMANY Keyboard language support---FRENCH send scan code Keyboard language support---SPANISH send scan code Keyboard language support---JAPANESE Keyboard language support---ITALIAN Message Terminator Keyboard terminator---none Keyboard terminator---Enter Keyboard terminator---H-TAB End Of Configuration Wireless Handheld Gun Type Scanner 53 USER’S MANUAL Start Of Configuration 4. Wand Emulation Setting Wand emulation is not supported as standard, if needed, please contact your distributor. (Code128, Code93 not supported) Wand Emulation All barcode will be decoded and transmitted in that symbology Enable Wand output data format as CODE39 Wand emulation data output black=high Scan this bar code to set quiet zones and spaces low and bars =high. Wand emulation data output black=low Scan this bar code to set quiet zones and spaces high and bars=low Idle = high Idle state refers to the TTL logic level of the Wand Emulation signal when not in use Idle = low Idle state refers to the TTL logic level of the Wand Emulation signal when not in use End Of Configuration 54 Wireless Handheld Gun Type Scanner USER’S MANUAL Start Of Configuration Wand Emulation (Cont’d) Wand emulation speed-----Low This option allows the transmission of wand emulation at 1ms narrow element width Wand emulation speed-----medium This option allows the transmission of wand emulation at 600us narrow element width Wand emulation speed-----high This option allows the transmission of wand emulation at 300us narrow element width Wand emulation speed-----higher This option allows the transmission of wand emulation at 100 us narrow element width End Of Configuration Wireless Handheld Gun Type Scanner 55 USER’S MANUAL Start Of Configuration 5. Smart Phone Software Keypad Control Setting Smart Phone Software Keypad Control Multi-media keyboard mode This option enables Multi-media keyboard mode Software keypad enable/disable This option enable or disable Software keypad To enable/disable Software keyboard: 1. 2. 3. 4. 5. Scan the Start Of Configuration barcode. Scan the Multi-media keyboard mode barcode. Scan the End Of Configuration barcode. Connect the scanner with a smart phone. Please see BT HID mode for instructions. With Multi-media keyboard mode enabled and smart phone connection made, you may scan the Software keypad enable/disable barcode to enable or disable the Software keypad. End Of Configuration 56 Wireless Handheld Gun Type Scanner USER’S MANUAL Start Of Configuration The Symbologies 1. Codabar Parameter Setting Barcode Value RC02 Barcode Label Description Codabar enable RD02 Codabar disable CB05 Codabar start/stop character transmissionЁnone CB06 Codabar start/stop character transmissionЁA,B,C,D CB07 Codabar start/stop character transmissionЁ DC1~DC4 CB08 Codabar start/stop character transmissionЁ a/t,b/n,c/*,d/e CB09 Codabar maximum length setting CB10 Codabar minimum length setting SET Confirm to save this setting (required for reading full ASCII table and length setting) End Of Configuration Wireless Handheld Gun Type Scanner 57 USER’S MANUAL Start Of Configuration Barcode Value CB13 Barcode Label Description No check character CB14 Validate modulo 16,but don’t transmit CB15 Validate modulo 16 and transmit DC50 Codabar data redundant check=off DC51 Codabar data redundant check=1 DC52 Codabar data redundant check=2 DC53 Codabar data redundant check=3 End Of Configuration 58 Wireless Handheld Gun Type Scanner USER’S MANUAL Start Of Configuration 2. Code 39 Parameter Setting Barcode Value RC01 Barcode Label Description Code 39 enable RD01 Code 39 disable RC13 Code 32 enable RD13 Code 32 disable DC00 Code 39 data redundant check=off DC01 Code 39 data redundant check=1 DC02 Code 39 data redundant check=2 DC03 Code 39 data redundant check=3 3901 Standard code 39 3902 Full ASCII code 39 3903 Code 39 start/stop character transmission 3904 Code 39 start/stop character without transmission End Of Configuration Wireless Handheld Gun Type Scanner 59 USER’S MANUAL Start Of Configuration Barcode Value 3905 Barcode Label Description Code 39 check digit calculate and transmit 3906 Code 39 check digit calculate but without transmit 3907 No check character 3908 Code 39 maximum length setting 3909 Code 39 minimum length setting SET Confirm to save this setting (required for reading full ASCII table and length setting) 3912 Code 32 (Italian pharmacy) transmit “A” character 3913 Code 32 (Italian pharmacy) without transmit ”A” character End Of Configuration 60 Wireless Handheld Gun Type Scanner USER’S MANUAL Start Of Configuration 3. Code 93 Parameter Setting Barcode Value RC08 Barcode Label Description Code 93 enable RD08 Code 93 disable DC30 Code 93 data redundant check=off DC31 Code 93 data redundant check=1 DC32 Code 93 data redundant check=2 DC33 Code 93 data redundant check=3 9301 Code 93 maximum length setting 9302 Code 93 minimum length setting SET Confirm to save this setting (required for reading full ASCII table and length setting) 9303 Code 93 check digit calculate but without transmit 9304 Code 93 check digit not calculate and without transmit 9305 Code 93 check digit calculate and transmit End Of Configuration Wireless Handheld Gun Type Scanner 61 USER’S MANUAL Start Of Configuration 4. Code 128 Parameter Setting Barcode Value RC06 Barcode Label Description Code 128 enable RD06 Code 128 disable RC10 EAN-128 enable RD10 EAN-128 disable DC40 Code 128 data redundant check=off DC41 Code 128 data redundant check=1 DC42 Code 128 data redundant check=2 DC43 Code 128 data redundant check=3 1803 No check character 1804 Calculate but not transmit 1805 Calculate and transmit 1806 Code 128 maximum length setting 1807 Code 128 minimum length setting SET Confirm to save this setting (required for reading full ASCII table and length setting) End Of Configuration 62 Wireless Handheld Gun Type Scanner USER’S MANUAL Start Of Configuration 5. Chinese Post Code Parameter Setting Barcode Value RC05 Barcode Label Description Chinese post code enable RD05 Chinese post code disable DC60 Chinese post code data redundant check=off DC61 Chinese post code data redundant check=1 DC62 Chinese post code data redundant check=2 DC63 Chinese post code data redundant check=3 SZ01 Chinese post code maximum length setting SZ02 Chinese post code minimum length setting SET Confirm to save this setting (required for reading full ASCII table and length setting) End Of Configuration Wireless Handheld Gun Type Scanner 63 USER’S MANUAL Start Of Configuration 6. MSI/Plessy Parameter Setting Barcode Value RC14 Barcode Label Description MSI enable RD14 MSI disable DC70 MSI data redundant check= off DC71 MSI data redundant check=1 DC72 MSI data redundant check=2 DC73 MSI data redundant check=3 MS01 MSI/Plessy maximum length setting MS02 MSI/Plessy minimum length setting SET MS03 MS04 MS05 MS06 MS07 MS08 Confirm to save this setting (required for reading full ASCII table and length setting) MSI/Plessy double check digit calculate but not transmit MSI/Plessy double check digit without calculate and transmit MSI/Plessy double check digit calculate but only first digit transmit MSI/Plessy double check digit calculate and both transmit MSI/Plessy single check digit calculate but without transmit MSI/Plessy single check digit calculate and transmit End Of Configuration 64 Wireless Handheld Gun Type Scanner USER’S MANUAL Start Of Configuration 7. Code 11 Interface Setting Barcode Value RC07 Barcode Label Description Code 11 enable RD07 Code 11 disable 1101 Code 11 maximum length setting 1102 Code 11 minimum length setting SET Confirm to save this setting (required for reading full ASCII table and length setting) 1103 Code 11 one check digit verification 1104 Code 11 two check digit verification 1105 Two Check for Code 11 check digit if code length is longer than 10 characters 1106 Disable verification 1107 Code 11 check digit transmitted 1108 Code 11 check digit not transmitted End Of Configuration Wireless Handheld Gun Type Scanner 65 USER’S MANUAL Start Of Configuration 8. ITF 2 of 5 Parameter Setting Barcode Value RC04 Barcode Label Description ITF 2 of 5 enable RD04 ITF 2 of 5 disable RC09 IATA code enable RD09 IATA disable DC80 ITF 25 data redundant check=off DC81 ITF25 data redundant check=1 DC82 ITF25 data redundant check=2 DC83 ITF25 data redundant check=3 IT03 ITF 2 of 5 no check character IT04 ITF 2 of 5 check digit calculate and transmit IT05 ITF 2 of 5 check digit calculate but without transmit End Of Configuration 66 Wireless Handheld Gun Type Scanner USER’S MANUAL Start Of Configuration Barcode Value IT01 Barcode Label Description ITF 2 of 5 code maximum length setting IT02 ITF 2 of 5 code minimum length setting IT06 ITF 2 of 5 one fixed length setting IT07 ITF 2 of 5 two fixed length setting SET Confirm to save this setting (required for reading full ASCII table and length setting) IT08 ITF 2 of 5 length variable End Of Configuration Wireless Handheld Gun Type Scanner 67 USER’S MANUAL Start Of Configuration 9. Standard 2 of 5 Parameter Setting Barcode Value RC22 Barcode Label Description Standard 2 of 5 code enable RD22 Standard 2 of 5 code disable D051 Standard 2 of 5 code maximum length setting D052 Standard 2 of 5 code minimum length setting SET Confirm to save this setting (required for reading full ASCII table and length setting) D053 Standard 2 of 5 code no check character D054 Standard 2 of 5 code check digit calculate and transmit D055 Standard 2 of 5 code check digit calculate but without transmit End Of Configuration 68 Wireless Handheld Gun Type Scanner USER’S MANUAL Start Of Configuration 10. Industrial 2 of 5 Parameter Setting Barcode Value RC21 Barcode Label Description Industrial 2 of 5 code enable RD21 Industrial 2 of 5 code disable D251 Industrial 2 of 5 code maximum length setting D252 Industrial 2 of 5 code minimum length setting SET Confirm to save this setting (required for reading full ASCII table and length setting) D253 Industrial 2 of 5 code no check character D254 Industrial 2 of 5 code check digit calculate and transmit D255 Industrial 2 of 5 code check digit calculate but without transmission End Of Configuration Wireless Handheld Gun Type Scanner 69 USER’S MANUAL Start Of Configuration 11. UPC/EAN/JAN Parameter Setting Barcode Value RC11 Barcode Label Description EAN convert to ISSN/ISBN enable RD11 EAN convert to ISSN/ISBN disable RC03 UPC/EAN/JAN enable RD03 UPC/EAN/JAN disable UE01 UPC/EAN/JAN all enable UE02 EAN-8 or EAN-13 enable UE03 UPC-A and EAN-13 enable UE04 UPC-A and UPC-E enable UE05 UPC-A enable UE06 UPC-E enable UE07 EAN-13 enable UE08 EAN-8 enable UE09 UPC/EAN Addendum disable End Of Configuration 70 Wireless Handheld Gun Type Scanner USER’S MANUAL Start Of Configuration Barcode Value UE10 Barcode Label Description Add on 5 only UE11 Add on 2 only UE12 Add on 2 or 5 UE13 Force UPC-E to UPC-A format enable UE14 Force UPC-E to UPC-A format disable UE15 Force UPC-A to EAN-13 format enable UE16 Force UPC-A to EAN-13 format disable UE44 Force EAN-8 to EAN-13 format enable UE45 Force EAN-8 to EAN-13 format disable UE17 Transmit UPC-A check digit enable UE18 Transmit UPC-A check digit disable UE19 Transmit UPC-E leading character enable UE20 Transmit UPC-E leading character disable UE21 Transmit UPC-E check digit enable UE22 Transmit UPC-E check digit disable End Of Configuration Wireless Handheld Gun Type Scanner 71 USER’S MANUAL Start Of Configuration Barcode Value UE23 Barcode Label Description Transmit EAN-8 check digit enable UE24 Transmit EAN-8 check digit disable UE25 Transmit EAN-13 check digit enable UE26 Transmit EAN-13 check digit disable UE27 Transmit UPC-A leading character enable UE28 Transmit UPC-A leading character disable UE30 Add-on format with separator UE31 Add-on format without separator UE60 EAN-13 country code first “0” can be transmitted UE61 EAN-13 country code first:”0” can’t be transmitted UE66 EAN-13 with first 0 ID code same as “UPC-A” UE67 EAN-13 with first 0 ID code same as “EAN-13” DC10 UPC-A data redundant check=off DC11 UPC-A data redundant check=1 End Of Configuration 72 Wireless Handheld Gun Type Scanner USER’S MANUAL Start Of Configuration Barcode Value DC12 Barcode Label Description UPC-A data redundant check=2 DC13 UPC-A data redundant check=3 DC14 UPC-E data redundant check=off DC15 UPC-E data redundant check=1 DC16 UPC-E data redundant check=2 DC17 UPC-E data redundant check=3 DC20 EAN-13 data redundant check=off DC21 EAN-13 data redundant check=1 DC22 EAN-13 data redundant check=2 DC23 EAN-13 data redundant check=3 DC24 EAN-8 data redundant check=off DC25 EAN-8 data redundant check=1 DC26 EAN-8 data redundant check=2 DC27 EAN-8 data redundant check=3 UE32 EAN/UPC +add-on (none mandatory) UE33 EAN/UPC +add-on (mandatory) End Of Configuration Wireless Handheld Gun Type Scanner 73 USER’S MANUAL Start Of Configuration UE35 EAN/UPC +add-on mandatory for 978/977 bookland (Supplement requirement, not sent for other) UE38 EAN/UPC +addon mandatory for 978/977 bookland (Supplement requirement, optional for other) UE42 EAN/UPC +addon mandatory for 491 Japanese bookland (Supplement requirement, not sent for other) UE43 EAN/UPC +addon mandatory 491 Japanese bookland (Supplement requirement, optional for other) End Of Configuration 74 Wireless Handheld Gun Type Scanner USER’S MANUAL Start Of Configuration 12. Telepen Parameter Setting Barcode Value RC25 Barcode Label Description Telepen enable RD25 Telepen disable TE03 Telepen numeric mode enable TE04 AIM Telepen enable End Of Configuration Wireless Handheld Gun Type Scanner 75 USER’S MANUAL Start Of Configuration 13. Matrix 2 of 5 Parameter Setting Barcode Value RC12 Barcode Label Description Matrix 2 of 5 enable RD12 Matrix 2 of 5 disable D151 Matrix 2 of 5 maximum length setting D152 Matrix 2 of 5 minimum length setting SET Confirm to save this setting (required for reading full ASCII table and length setting) D153 Matrix 2 of 5 no check character D154 Matrix 2 of 5 check digit calculate and transmit D155 Matrix 2 of 5 check digit calculate but without transmission End Of Configuration 76 Wireless Handheld Gun Type Scanner USER’S MANUAL Start Of Configuration 14. GS1 DataBar Parameter Setting There are 7 kinds of barcodes in the GS1 DataBar family and they are categorized into three groups. Barcode types in the same group use the same barcodes for setting. Group Representative Contents Group 1 GS1 DataBar Omnidirectional GS1 DataBar Omnidirectional (Formally RSS-14) GS1 DataBar Truncated GS1 DataBar Stacked GS1 DataBar Stacked Omnidirectional Group 2 GS1 DataBar Limited GS1 DataBar Limited (Formally RSS Limited) Group 3 GS1 DataBar Expanded GS1 DataBar Expanded (Formally RSS Expanded) GS1 DataBar Expanded Stacked GS1 DataBar Omnidirectional (Formally RSS-14) Barcode Value RC15 Barcode Label Description GS1 DataBar Omnidirectional enable RD15 GS1 DataBar Omnidirectional disable SS00 Transmit GS1 DataBar Omnidirectional check digit SS01 Do not transmit GS1 DataBar Omnidirectional check digit SS02 Transmit GS1 DataBar Omnidirectional application ID (01) SS03 Do not transmit GS1 DataBar Omnidirectional application ID (01) SS05 GS1 DataBar Omnidirectional /EAN-128 emulation enable SS04 GS1 DataBar Omnidirectional /EAN-128 emulation disable End Of Configuration Wireless Handheld Gun Type Scanner 77 USER’S MANUAL Start Of Configuration GS1 DataBar Limited (Formally RSS Limited) Barcode Value RC16 Barcode Label Description GS1 DataBar Limited enable RD16 GS1 DataBar Limited disable SS10 Transmit GS1 DataBar Limited check digit SS11 Don’t transmit GS1 DataBar Limited check digit SS12 Transmit GS1 DataBar limited application ID (01) SS13 Do not transmit GS1 DataBar limited application ID End Of Configuration 78 Wireless Handheld Gun Type Scanner USER’S MANUAL Start Of Configuration GS1 DataBar Expanded (Formally RSS Expanded) Barcode Value RC17 Barcode Label Description GS1 DataBar Expanded enable RD17 GS1 DataBar Expanded disable SS07 GS1 DataBar Expanded/EAN-128 emulation enable SS06 GS1 DataBar Expanded/EAN-128 emulation disable SS08 GS1 DataBar Expanded check digital enable SS09 GS1 DataBar Expanded check digital disable SS16 Transmit GS1 DataBar Expanded application ID (01) SS17 Do not transmit GS1 DataBar Expanded application ID End Of Configuration Wireless Handheld Gun Type Scanner 79 USER’S MANUAL Start Of Configuration Data Editing 1. Identifier Code Barcode Value IS00 Barcode Label Description Disable identifier code IS01 Enable identifier code table as factory standard IS03 Enable identifier code table as AIM standard. CI01 Code 39 identifier code setting CI02 ITF 2 of 5 identifier code setting CI03 Chinese Post Code identifier code setting CI04 UPC-E identifier code setting CI05 UPC-A identifier code setting CI06 EAN-13 identifier code setting CI07 EAN-8 identifier code setting SET Confirm to save this setting (required for reading full ASCII table and length setting) End Of Configuration 80 Wireless Handheld Gun Type Scanner USER’S MANUAL Start Of Configuration Barcode Value CI08 Barcode Label Description Codabar identifier code setting CI09 Code 128 identifier code setting CI10 Code 93 identifier code setting CI11 MSI identifier code setting CI12 GS1 DataBar Omnidirectional identifier code setting CI13 GS1 DataBar Limited identifier code setting CI14 GS1 DataBar expanded identifier code setting CI15 Industrial 2 of 5 identifier code setting CI16 Code 11 Identifier code setting CI17 Standard 2 of 5 identifier code setting CI18 Matrix 2 of 5 identifier code setting SET Confirm to save this setting (required for reading full ASCII table and length setting) End Of Configuration Wireless Handheld Gun Type Scanner 81 USER’S MANUAL Start Of Configuration 2. Header and Trailer Barcode Value CP11 CP12 HT01 HT02 HT03 HT04 SET Barcode Label Description Add code length as header enable (2 digits) Add code length as header disable (2 digits) Header (Preamble) Trailer (Postamble) Truncate header character Truncate trailer character Confirm to save this setting (required for reading full ASCII table and length setting) End Of Configuration 82 Wireless Handheld Gun Type Scanner USER’S MANUAL Start Of Configuration Full ASCII Code 39 Table Code 39 ASCII Hexa code Code 39 ASCII Hexacode Full ASCII ---NUL 00 Full ASCII ---SI Function key-----“Shift” 0F Full ASCII ---SOH Function key-----“Ins” 01 10 Full ASCII ---STX Function key-----“Del” 02 Full ASCII ---DLE Function key----“5(num)” Full ASCII ---DC1 Function key-----“F1” Full ASCII ---ETX Function key-----“Home” 03 Full ASCII ---DC2 Function key-----“F2” 12 Full ASCII ---EOT Function key-----“End” 04 Full ASCII ---DC3 Function key-----“F3” 13 Full ASCII ---ENQ Function key-----“Up arrow” Full ASCII ---ACK Function key-----“Down arrow” Full ASCII ---BEL Function key-----“Left arrow” Full ASCII ---BS Function key----“Backspace” Full ASCII ---HT Function key-----“TAB” 05 Full ASCII ---DC4 Function key-----“F4” 14 06 Full ASCII ---NAK Function key-----“F5” 15 07 Full ASCII ---SYN Function key-----“F6” 16 08 Full ASCII ---ETB Function key-----“F7” 17 09 Full ASCII ---CAN Function key-----“F8” 18 Full ASCII ---LF Function key-----“Enter (alpha numeric)” Full ASCII ---VT Function key-----“right arrow” Full ASCII ---FF Function key-----“PgUp” 0A Full ASCII ---EN Function key-----“F9” 19 0B Full ASCII ---SUB Function key-----“F10” 1A 0C Full ASCII ---ESC Function key-----“F11” 1B Full ASCII ---CR Function key----“Enetr(num.)” Full ASCII ---SO Function key-----“PgDn” 0D Full ASCII ---FS Function key-----“F12” 1C 0E Full ASCII ---GS Function key-----“ESC” 1D End Of Configuration Wireless Handheld Gun Type Scanner 11 83 USER’S MANUAL Start Of Configuration Full ASCII Code 39 Table (continued) HexaCode 39 ASCII code Code 39 ASCII Hexacode Full ASCII ---RS Function key-----“CTL(L)” 1E Full ASCII ---- 2D Full ASCII ---US Function key-----“ALT(L)” 1F Full ASCII ---. 2E Full ASCII ---SP 20 Full ASCII ---/ 2F Full ASCII ---! 21 Full ASCII ---0 30 Full ASCII ---“ 22 Full ASCII ---1 31 Full ASCII ---# 23 Full ASCII ---2 32 Full ASCII ---$ 24 Full ASCII ---3 33 Full ASCII ---% 25 Full ASCII ---4 34 Full ASCII ---& 26 Full ASCII ---5 35 Full ASCII ---‘ 27 Full ASCII ---6 36 Full ASCII --- ( 28 Full ASCII ---7 37 Full ASCII ---) 29 Full ASCII ---8 38 Full ASCII ---* 2A Full ASCII ---9 39 Full ASCII ---+ 2B Full ASCII ---: 3A Full ASCII ---, 2C Full ASCII ---; 3B End Of Configuration 84 Wireless Handheld Gun Type Scanner USER’S MANUAL Start Of Configuration Full ASCII Code 39 Table (continued) Code 39 ASCII Hexacode Code 39 ASCII Hexacode Full ASCII ---< 3C Full ASCII ---K 4B Full ASCII ---= 3D Full ASCII ---L 4C Full ASCII ---> 3E Full ASCII ---M 4D Full ASCII ---? 3F Full ASCII ---N 4E Full ASCII ---@ 40 Full ASCII ---O 4F Full ASCII ---A 41 Full ASCII ---P 50 Full ASCII ---B 42 Full ASCII ---Q 51 Full ASCII ---C 43 Full ASCII ---R 52 Full ASCII ---D 44 Full ASCII ---S 53 Full ASCII ---E 45 Full ASCII ---T 54 Full ASCII ---F 46 Full ASCII ---U 55 Full ASCII ---G 47 Full ASCII ---V 56 Full ASCII ---H 48 Full ASCII ---W 57 Full ASCII ---I 49 Full ASCII ---X 58 Full ASCII ---J 4A Full ASCII ---Y 59 End Of Configuration Wireless Handheld Gun Type Scanner 85 USER’S MANUAL Start Of Configuration Full ASCII Code 39 Table (continued) HexaCode 39 ASCII code Code 39 ASCII Hexacode Full ASCII ---Z 5A Full ASCII ---i 69 Full ASCII ---[ 5B Full ASCII ---j 6A Full ASCII ---\ 5C Full ASCII ---k 6B Full ASCII ---] 5D Full ASCII ---l 6C Full ASCII ---^ 5E Full ASCII ---m 6D Full ASCII ---_ 5F Full ASCII ---n 6E Full ASCII ---` 60 Full ASCII ---o 6F Full ASCII ---a 61 Full ASCII ---p 70 Full ASCII ---b 62 Full ASCII ---q 71 Full ASCII ---c 63 Full ASCII ---r 72 Full ASCII ---d 64 Full ASCII ---s 73 Full ASCII ---e 65 Full ASCII ---t 74 Full ASCII ---f 66 Full ASCII ---u 75 Full ASCII ---g 67 Full ASCII ---v 76 Full ASCII ---h 68 Full ASCII ---w 77 End Of Configuration 86 Wireless Handheld Gun Type Scanner USER’S MANUAL Start Of Configuration Full ASCII Code 39 Table (continued) HexaCode 39 ASCII code Code 39 ASCII Hexacode Full ASCII ---x 78 Full ASCII ---| 7C Full ASCII ---y 79 Full ASCII ---} 7D Full ASCII ---z 7A Full ASCII ---~ 7E Full ASCII ---{ 7B Full ASCII ---DEL 7F End Of Configuration Wireless Handheld Gun Type Scanner 87 USER’S MANUAL Appendix 1: USB Virtual COM Driver Installation Contact your distributor to get the driver and follow the steps below to enable USB virtual COM port. 88 1. Connect the handheld scanner and the host (e.g. a PC) with a USB interface cable. 2. Enable USB virtual COM port with programming barcode on page 32. 3. After the programming, the host would request driver installation. Browse your files to locate the driver and start installation. 4. The USB virtual COM port is ready for use after driver installation. Wireless Handheld Gun Type Scanner USER’S MANUAL Appendix 2: Barcode Length Setting Introduction The length of a barcode is the number of characters it contains, including check digits. As listed in the Default Parameters section, each barcode type has different default length. You may change the setting by the following procedure. To set up barcode length, the paramours to be determined are barcode type and the desired barcode length. Barcode length is consisted of 2 digits. For numbers smaller than 10, you need to add a “0” in the front. Example If the barcode length is 4 to 12 digits, the steps would be as below: Start Set up barcode length Start of Configuration Set up minimum barcode length Set up maximum barcode length End End of Configuration Scan the “Start of configuration” barcode Scan the “Min“ barcode Set the “Max” barcode Scan the “Set” barcode to save this setting Read the “Full ASCII code 39” barcode Scan the first digit: 0 Set up the first digit: 1 Scan the “End of configuration” barcode Scan the second digit: 4 Set up the second digit: 2 Turn to the page of the barcode type to be set up Use the ASCII table (Appendix 4) to set up barcode length. Be sure to enable the full ASCII code 39 option before you start and read the “Set” label to set your choice into memory. Wireless Handheld Gun Type Scanner 89
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Author : martine.mo Company : Create Date : 2012:06:13 16:54:25+08:00 Modify Date : 2012:06:13 16:54:25+08:00 Source Modified : D:20120601092047 Subject : XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Producer : Acrobat Distiller 10.1.3 (Windows) Keywords : Creator Tool : Acrobat PDFMaker 9.1 for Word Metadata Date : 2012:06:13 16:48:35+08:00 Document ID : uuid:61e0403c-1d46-4077-b95b-f13ebf75fa51 Instance ID : uuid:acef0c15-563c-4ddd-9a4a-72dfe66cd8d1 Format : application/pdf Creator : martine.mo Title : Description : Page Count : 99EXIF Metadata provided by EXIF.tools