Zebra Technologies MD-TRCV-24GHZ Modular Transmitter User Manual 2400 wireless

Zebra Technologies Corporation Modular Transmitter 2400 wireless

Users manual

2400 Wireless2.4 GHz TransceiverPart Number: CC15380-1FeaturesThe Zebra 2400 Wireless is a 2.4 Ghz radiodesigned for OEM applications that oper-ate in the unlicensed FCC band between2.4-2.5 Ghz. The 2400 Wireless can beused for communications where physicalconnection is not desired. The followingobjectives can be achieved with the 2400Wireless, (i) provides a limited range radio(20-30 feet line of sight), (ii) minimizes partscount and associated cost, (iii) acts as acable replacement when used together withZebra Wireless printers. When combinedwith Zebra’s Intelligent Wireless Controller(part number CQ13867-1), the 2400 Wire-less can be attached to any RS232C port.To minimize integration headaches, the 2400Wireless has modular FCC approval, which means that no additional FCCapproval is required by the OEM providing an approved antenna is used.Note: The modular approval for this radio only applies for battery powered equipment.Installation of this radio into A.C. connected equipment requires additional regulatoryapproval. Please contact Zebra Technologies Corporation for details.ElectricalInput Voltage: Vcc = 5 Volts +,-10%Power Dissipation: 250 mW (receive mode)350mW (transmit mode)<5 mW (sleep mode)Current Consumption: 50 mA (receive mode)70 mA (transmit mode)<1 mA (sleep mode)Operating Frequency: 2.482 GHzTransmit Power Output: -10 dBm (typical)Receiver Sensitivity: -85 dBm (typical)Out of band interferingsignal rejection: 60 dB (typical)Baud rate: user selectableJ1 Pin Assignments: Pin # Signal Name1DescriptionPin 1 sleep/awake* 1 = sleepPin 2 VccPin 3 RXD Receive DataPin 4 TX/RX* 1 = transmitPin 5 No connectPin 6 TXD Transmit DataPin 7 GNDPin 8 GNDJ2 Pin Assignments: Pin # Signal Name1Description(Optional) Pin 1 GNDPin 2 GNDJ3 Pin Assignments: Pin # Signal Name1Description(Optional) Pin 1 GNDPin 2 GNDActual Size1. All signals are at CMOS levels
RF FILTERTX SAWMODULEDATABUFFERSRX SAWMODULEDATA BUFFERSCONTROL LOGICTXDRXDSLEEP/AWAKE*TX/RX*TX MIXRX MIXLOCALOSCILLATOR0.0000.2350.3120.5400.8450.7681.0800.1942.1891.3642.3572.4470.0000.070 0.2500.0620.080J1J2J318.125, 2 placesAntenna Connector2.253110.0000.1200.0902400 WirelessBlock DiagramSoftware When the Intelligent Wireless Controller (P/N CQ13967-1) is not used, Zebra can provideC source code for a CS/CDMA collision avoidance communications protocol. This soft-ware supports multiple radio pairs operating in proximity to each other, and implementserror detection, retries and radio address association. The radio address associationalgorithm is based on radio or product serial number.Regulatory Approvals: FCC Modular, ID Number: I28MD-TRCV-24GHZCanada: Canada RSS210 Certification # 37981032228AProduct Labelling Any final product that contains this radio must have aRequirements permanently affixed label visible from the outside of theproduct that says the following: “Contains FCC ID:I28MD-TRCV-24GHz.”Physical Connectors: Antenna - SSMT, M/A-COM part number 2367-5002-54Data (J1) - 8 pin female, Samtec part number SLM-108-01-S-SOptional ground connectors (J2, J3)- 2 pin female, Samtec partnumber SLM-102-01-S-SConnectors mate with Samtec MTMS family. Part number is dependent ondesired board spacing.Dimensions:©2000 Zebra Technologies Corporation all rights reserved.Specifications for information purposes and are subject to change.WARNING: Changes or modifications to this radio not expressly approved by Zebra TechnologiesCorporation may void the user’s authority to operate the equipment under the modular approval withFCC ID# I28MD-TRCV-24GHZ.Likewise, the antenna used with this radio must be approved by Zebra for the modular approval to bevalid.All products and brand names are trademarks of their respective companies.P/N AT 15380 10/2000 Rev. 1.2

Navigation menu