Zebra Technologies MD-TRCV-24GHZ Modular Transmitter User Manual 2400 wireless

Download:
Mirror Download [FCC.gov]
Document ID	120881
Application ID	zJe5hghJ/h6rGyrqqSJPfQ==
Document Description	Users manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	24.75kB (309388 bits)
Date Submitted	2000-10-12 00:00:00
Date Available	2000-10-12 00:00:00
Creation Date	2000-10-10 14:45:57
Producing Software	Acrobat Distiller 4.0 for Macintosh
Document Lastmod	2000-10-10 14:53:39
Document Title	2400 wireless
Document Creator	Adobe PageMaker 6.52

2400 Wireless
2.4 GHz Transceiver
Part Number: CC15380-1
Features
The Zebra 2400 Wireless is a 2.4 Ghz radio
designed for OEM applications that operate in the unlicensed FCC band between
2.4-2.5 Ghz. The 2400 Wireless can be
used for communications where physical
connection is not desired. The following
objectives can be achieved with the 2400
Wireless, (i) provides a limited range radio
(20-30 feet line of sight), (ii) minimizes parts
count and associated cost, (iii) acts as a
cable replacement when used together with
Zebra Wireless printers. When combined
with Zebra’s Intelligent Wireless Controller
(part number CQ13867-1), the 2400 Wireless can be attached to any RS232C port.
Actual Size
To minimize integration headaches, the 2400
Wireless has modular FCC approval, which means that no additional FCC
approval is required by the OEM providing an approved antenna is used.
Note: The modular approval for this radio only applies for battery powered equipment.
Installation of this radio into A.C. connected equipment requires additional regulatory
approval. Please contact Zebra Technologies Corporation for details.
Electrical
Input Voltage:
Power Dissipation:
Current Consumption:
Operating Frequency:
Transmit Power Output:
Receiver Sensitivity:
Out of band interfering
signal rejection:
Baud rate:
J1 Pin Assignments:
Vcc = 5 Volts +,-10%
250 mW (receive mode)
350mW (transmit mode)
<5 mW (sleep mode)
50 mA (receive mode)
70 mA (transmit mode)
<1 mA (sleep mode)
2.482 GHz
-10 dBm (typical)
-85 dBm (typical)
60 dB (typical)
user selectable
Pin #
Signal Name1
Pin 1
sleep/awake*
Pin 2
Vcc
Pin 3
RXD
Pin 4
TX/RX*
Pin 5
No connect
Pin 6
TXD
Pin 7
GND
Pin 8
GND
Description
1 = sleep
Receive Data
1 = transmit
Transmit Data
J2 Pin Assignments:
(Optional)
Pin #
Pin 1
Pin 2
Signal Name1
GND
GND
Description
J3 Pin Assignments:
(Optional)
Pin #
Pin 1
Pin 2
Signal Name1
GND
GND
Description
1. All signals are at CMOS levels
2400 Wireless
Block Diagram
TX
MIX
RF FILTER
DATA
BUFFERS
CONTROL
LOGIC
LOCAL
OSCILLATOR
RX
MIX
RX SAW
MODULE
DATA
BUFFERS
TXD
TX/RX*
SLEEP/
AWAKE*
RXD
When the Intelligent Wireless Controller (P/N CQ13967-1) is not used, Zebra can provide
C source code for a CS/CDMA collision avoidance communications protocol. This software supports multiple radio pairs operating in proximity to each other, and implements
error detection, retries and radio address association. The radio address association
algorithm is based on radio or product serial number.
Regulatory
Approvals:
Canada:
Product Labelling
Requirements
Physical
Connectors:
FCC Modular, ID Number: I28MD-TRCV-24GHZ
Canada RSS210 Certification # 37981032228A
Any final product that contains this radio must have a
permanently affixed label visible from the outside of the
product that says the following: “Contains FCC ID:
I28MD-TRCV-24GHz.”
2.189
1.364
Antenna - SSMT, M/A-COM part number 2367-5002-54
Data (J1) - 8 pin female, Samtec part number SLM-108-01-S-S
Optional ground connectors (J2, J3)- 2 pin female, Samtec part
number SLM-102-01-S-S
Connectors mate with Samtec MTMS family. Part number is dependent on
desired board spacing.
Dimensions:
1.080
0.845
0.768
0.540
0.312
0.235
J2
.125, 2 places
J1
J3
2.357
2.447
2.253
0.000
0.090
0.000
0.194
Software
TX SAW
MODULE
0.250
0.070
0.000
Antenna Connector
0.062
0.080
0.120
©2000 Zebra Technologies Corporation all rights reserved.
Specifications for information purposes and are subject to change.
WARNING: Changes or modifications to this radio not expressly approved by Zebra Technologies
Corporation may void the user’s authority to operate the equipment under the modular approval with
FCC ID# I28MD-TRCV-24GHZ.
Likewise, the antenna used with this radio must be approved by Zebra for the modular approval to be
valid.
All products and brand names are trademarks of their respective companies.
P/N AT 15380 10/2000 Rev. 1.2

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Encryption                      : Standard V1.2 (40-bit)
User Access                     : Print, Fill forms, Extract, Assemble, Print high-res
Create Date                     : 2000:10:10 14:45:57
Producer                        : Acrobat Distiller 4.0 for Macintosh
Subject                         : 2400 wireless
Creator                         : Adobe PageMaker 6.52
Title                           : 2400 wireless
Author                          : 
Modify Date                     : 2000:10:10 14:53:39-04:00
Page Count                      : 2

EXIF Metadata provided by EXIF.tools