Zebra Technologies MD-ZBR5QLN Zebra Embedded BT radio User Manual 2 of 3

Zebra Technologies Corporation Zebra Embedded BT radio 2 of 3

Contents

User Manual 2 of 3

Download: Zebra Technologies MD-ZBR5QLN Zebra Embedded BT radio User Manual 2 of 3
Mirror Download [FCC.gov]Zebra Technologies MD-ZBR5QLN Zebra Embedded BT radio User Manual 2 of 3
Document ID1439454
Application IDBA7kicZAqJefrm1zj8EzLA==
Document DescriptionUser Manual 2 of 3
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize219.71kB (2746424 bits)
Date Submitted2011-03-29 00:00:00
Date Available2011-03-29 00:00:00
Creation Date2011-03-09 16:00:55
Producing SoftwareAdobe PDF Library 9.0
Document Lastmod2011-03-28 17:35:50
Document TitleUser Manual 2 of 3
Document CreatorAdobe InDesign CS4 (6.0.6)

Soft Keys
Programmable LCD Settings
In addition to the status icons, the LCD control panel can display
other printer settings and functions as text. Applications can be written to allow the user to view and /or modify these settings using the
scroll and select keys on the display. The menu that comes with the
printer provides access to the most commonly used parameters. Refer
to the CPCL Programming Manual for a complete list of the parameters, and for details on how to change the front panel display (p/n
PROMAN-CPCL at www.zebra.com/manuals).
The LCD backlighting option allows viewing of the screen in a dark
environment, or provides better contrast in a very bright environment. The QLn320 can be programmed to enter a low power mode
(Backlight Off) during periods of front panel inactivity. While in low
power mode, the screen is populated with menus and status icons,
data which may or may not be readable depending on ambient light
conditions.
The QLn320 provides a configurable time delay from the time the
backlight is turned on to when it turns off. The time range for this delay is 5 to 1200 seconds with a default time of 10 seconds. The backlight can be activated within one second after any of the cursor, select,
or soft keys is pressed. (The feed button does not activate the backlight.) The status bar icons, the user space content, and the navigation
bar will remain on the screen with the backlight off.
Extensive use of the display backlight will decrease the time
the printer can run between charges. Refer to the section
“Extending Battery Life” for more information.
31
QLn Series User Guide
Verify the Printer Is Working
Before you connect the printer to your computer or portable data
terminal, make sure that the printer is in proper working order. You
can do this by printing a configuration label using the “two key” method. If you can’t get this label to print, refer to “Troubleshooting”.
Printing a Configuration Label
1. Turn the printer off. Load the media compartment with
journal media (media with no black bars printed on the
back)
2. Press and hold the Feed Button.
3. Press and release the Power button and keep the Feed
button pressed. When printing starts, release the Feed
button.
The unit will print a line of interlocking “x” characters to
ensure all elements of the print head are working, print out the
version of software loaded in the printer and then print two reports.
The report indicates model, serial number, baud rate, and more
detailed information on the printer’s configuration and parameter settings. (See the Troubleshooting Section for sample printouts and a further discussion on how to use the configuration label as a diagnostic
tool.)
Connecting the Printer
The printer must establish communications with a host terminal which sends the data to be printed. Communications
occur in four basic ways:
• QLn320 printers can communicate by cable via either RS-232C or
USB 2.0 protocols. USB drivers are included in the Zebra Designer
Driver which can be downloaded from www.zebra.com/drivers.
• By means of a Bluetooth™ short range radio frequency link.
(Optional)
• By means of a wireless LAN (Local Area Network) per 802.11 specifications. (Optional)
• By means of the Ethernet when docked on the Ethernet cradle.
(Optional)
32
QLn Series User Guide
Cable Communication
Caution • The printer should be turned off before connecting or
disconnecting a communications cable.
The QLn320 printer can communicate by cable; the specific
cable supplied with your printer will vary with the host terminal and your model printer.
RS-232C Communications
The 14-pin serial connector on your communications cable plugs
into the serial communications port on the side of the printer. QLn320
model printers also have a USB port.
USB Communications
The small 5-pin connector on the USB cable plugs into the
printer. The connectors are keyed to assure correct alignment; do not try to force the cable if it does not plug in. The
Figure 17: Cable Communications
Communications
Port
Communications Cable to Terminal
Part numbers vary. Refer to Appendix A.
Figure 18: Communications with a P.C.
RS-232C or USB Communications
Cable to Computer
Refer to Appendix A for part numbers.
33
QLn Series User Guide
other end of the cable must be plugged into the host terminal
as shown in Figure 18, or to a serial or USB port on a computer (Figure 18). The QLn320 series is configured with the USB
Open HCI interface driver allowing it to communicate with
Windows® based devices.
USB drivers are included in the Zebra Designer Driver which can be
downloaded from the Zebra Web site. Other terminals or communications devices may require the installation of special drivers to use the
USB connection. Consult the factory for further details.
Providing Strain Relief for Communications Cable
If you are connecting either a USB or RS-232 communications cable
to the printer permanently, access the communications port on the
side of the printer next to the latch release lever. Plug the connector
into the appropriate port and align the plastic locking cap with the cut
outs shown below. Rotate the locking cap clockwise to lock the cable
in place. (Turn counterclockwise to unlock the cable.) Once locked in
place, this provides strain relief for the cable and will prevent the cable
from disconnecting from the printer.
Note: Only one cable can be present in the USB/RS-232
Figure 19: Communications Port
RS-232 Port
Align locking
connector
with these
cut-outs.
USB Port
34
QLn Series User Guide
Figure 20: Communications Port Strain Relief
Rotate locking cap in a
clockwise direction to lock
cable in place.
35
QLn Series User Guide
Wireless Communications with Bluetooth™
Bluetooth is a worldwide standard for the exchange of data between two devices via radio frequencies. Bluetooth radios are
relatively low powered to help prevent interference with other devices running at similar radio frequencies. This limits the range of a
Bluetooth device to about 10 meters (32 feet). Both the printer and
the device it communicates with must follow the Bluetooth standard.
Other than conditions specified elsewhere in this manual, only one of
the radio options can be installed in the printer at one time and the
antenna used for these transmitters must not be co-located or must
not operate in conjunction with any other antenna.
Bluetooth Networking Overview
Each Bluetooth enabled QLn320 printer is identified by a unique
Bluetooth Device Address (BDA). In order to exchange data, two
Bluetooth enabled devices must establish a connection.
Bluetooth software is always running in the background,
ready to respond to connection requests. One device (known
as the master or the client) must request a connection with another. The second device (the slave or the server) then accepts
or rejects the connection. A Bluetooth enabled QLn320 printer will normally act as a slave creating a miniature network
with the terminal sometimes referred to as a “piconet”.
For the most part, communications using the Bluetooth protocol are initiated and processed without any operator intervention.
continued
36
QLn Series User Guide
WLAN Overview
QLn320 printers can be equipped with a radio using the industry standard 802.11 protocols. They will have the FCC ID
number on the serial number label on the back of the unit.
• QLn320 series Wireless Network Printers with the Zebra 802.11
WLAN radio module can be identified by the text “Wireless
Network Printer” on the serial number label on the back of the
printer.
• These printers allow wireless communication as a node within a
local area network (LAN) and its wireless capabilities allow communications from any point within the LAN’s perimeter. Methods
of establishing communications to the printer will vary with
each LAN application.
General information on establishing WLAN communications can be
found in either the ”CPCL Programming Manual” or the “Quick Start
Guide for Mobile Wireless Printers” both available on-line. More information and LAN configuration utilities are included in Zebra’s Net
Bridge™ program (version 2.8 and later). Net Bridge may be downloaded from the Zebra Web site.
Setting Up the Software
QLn320 printers use Zebra’s CPCL and ZPL Programming languages
which were designed for mobile printing applications. CPCL and ZPL
are fully described in the ”CPCL Programming Manual” and the “ZPL
Programming Guide” available on-line at www.zebra.com/manuals.
You can also use Designer Pro, Zebra’s Windows® based label creation program which uses a graphical interface to create and edit labels in the CPCL language.
Refer to Appendix F for tips on downloading the Designer Pro application from Zebra’s Web site.
37
QLn Series User Guide
Using the Accessories
Swivel Belt Clip
Refer to Figure 21. Most QLn320 printers have a belt clip
(p/n P1024458) installed as a standard feature. To use: hook
the clip over your belt, and ensure that the clip is securely attached to the belt. The belt clip will pivot to allow you to move
freely while wearing the printer.
In order to install or remove the Belt Clip you will need to remove
the battery pack.
Figure 21: Using the Belt Clip
Clip printer to
belt
Belt
Printer can
pivot freely
38
QLn Series User Guide
Adjustable Shoulder Strap
Refer to Figure 22 if your printer is equipped with the shoulder strap option (p/n P1028227). Insert each end of the shoulder strap into the cut-outs in each top corner of the printer and
secure the looped end over the button on the end of the strap
to fasten.
Hold the buckle and pull the strap as shown below until you achieve
Figure 22: Using the Optional Shoulder Strap
Pull Strap here
to lengthen.
Hold Buckle.
Pull
Strap
here to
shorten.
Insert loop into
cut-outs on
printer.
End of
strap
Button
Loop
continued
39
QLn Series User Guide
the desired length.
Hand Strap
The QLn320 hand strap accessory (p/n P1028226) attaches to the
printer’s cut-outs as does the shoulder strap to provide the user with
a convenient and secure method of carrying the printer. To attach the
hand strap to the printer:
• Insert the end of the strap through the cut out on the front of the
printer as shown.
• Loop the end of the strap back around the cut out and secure it
over the button.
• Repeat this process for the opposite end of the strap.
Figure 23: Detachable Hand Strap
Loop strap into
cut-outs on
printer.
The QLn320 printer also features two mounting holes on the
base of the printer to accommodate future mounting options.
40
QLn Series User Guide
Preventive Maintenance
Extending Battery Life
• Never expose the battery to direct sunlight or temperatures over 104° F (40° C).
• Always use a Zebra charger designed specifically for Lithium-Ion
batteries. Use of any other kind of charger may damage the battery.
• Use the correct media for your printing requirements. An
authorized Zebra re-seller can help you determine the optimum media for your application.
• If you print the same text or graphic on every label, consider using a pre-printed label.
• Choose the correct print darkness, and print speed for
your media.
• Use software handshaking (XON/XOFF) whenever possible.
• Remove the battery if the printer won’t be used for a day or more
and you’re not performing a maintenance charge.
• Consider purchasing an extra battery.
• Remember that any rechargeable battery will lose its
ability to maintain a charge over time. It can only be recharged a finite number of times before it must be replaced. Always dispose of batteries properly. Refer to
Appendix E for more information on battery disposal.
General Cleaning Instructions
Caution • Avoid possible personal injury or damage to the printer: never
insert any pointed or sharp objects into the printer.
Always turn the printer off before performing any cleaning
procedures.
Use care when working near the tear bar. The edges are very sharp.
Caution • The printhead can be very hot after prolonged printing.
Allow it to cool off before attempting any cleaning procedures.
Only use the cleaning pen supplied with the printer or a cotton swab
saturated with alcohol for cleaning the printhead.
Caution • Use only cleaning agents specified in the following tables.
Zebra Technologies Corporation will not be responsible for damage
caused by any other cleaning materials used on this printer.
41
QLn Series User Guide
QLn320 Cleaning
Area
Method
Printhead (Figure 24)
Use the supplied cleaning pen or 70%
Isopropyl alcohol on a cotton swab to
clean the print elements from end to
end (the print elements are located in
the thin gray line on the printhead).
Platen Roller (Figure 24)
Rotate the platen roller and clean it
thoroughly with the cleaning pen or
70% Isopropyl alcohol and a cotton
swab.
Platen Roller (Figure 25)
Units with linerless platens: Rotate
platen & clean bearing points only.
Avoid use of alcohol on the surface
of linerless platens
Peel bar (Figure 24)
Tear bar (Figure 24)
Exterior
Clean thoroughly with the cleaning pen
or 70% Isopropyl alcohol and a cotton
swab.
Interval
After every five rolls of
media (or more often, if
needed),
Linerless media requires
more frequent cleaning
As needed
As needed
Water-dampened cloth or 70%
Isopropyl alcohol wipe.
Interior (Figure 24)
Brush/air blow. Ensure the Bar
Sensor, Gap Sensor and Label
Present Sensor windows are free
of dust.
Interior (Figure 25)
Units with linerless platens: Clean inside
surfaces of edge guides & media rollers
with the supplied cleaning pen or 70%
Isopropyl alcohol on a cotton swab.
42
QLn Series User Guide
As needed
After every five rolls of
media (or more often, if
needed)
Figure 24: Cleaning the QLn320
Platen surface
Peeler Bar
Bar Sensor
Printhead
Elements
Peeler
Bar
Gap
Sensor
Tear Bar
Label
Presence
Sensor
Figure 25: Cleaning the Linerless QLn320
Scraper
Platen surface
Avoid using alcohol
on linerless platen
surface.
Bearing Points
Media Support
Disks, Inner
surfaces on
both sides.
Linerless Platens only
Linerless units only.
43
QLn Series User Guide
Troubleshooting
Figure 26 QLn320 Control Panels
Green/Yellow/
Amber LED
Front Control Panel
Status icons
LCD Control Panel
Front Control Panel
If the printer is not functioning properly, refer to the chart
below to find the state of the LED charge indicator on the
Front Control Panel. Then refer to the Troubleshooting topic
referenced in the chart to resolve the problem.
Green
Ref. to
Topic
Yellow
Amber
Indication
Solid
Off
Off
Fully charged
n/a
Off
Solid
Off
Charging
n/a
Off
Off
Solid
Fault
1, 6, 12
44
QLn Series User Guide
LCD Control Panel Indicators
The top of the display shows several icons which indicate
the status of various printer functions. Check the indicator status, then refer to the Troubleshooting topic referenced in the
chart to resolve the problem.
Icon
Status
Indication
On
Bluetooth Link established
Not Present
Bluetooth Link inactive
Blinking
Topic
n/a
Connecting or Transmitting Labels
Antenna Blinking
Looking for AP
Antenna Blinking/1 Parenthesis Solid
WLAN Associated & Attempting Authentication
Antenna and 2 Parentheses
Solid
WLAN Associated and
Authenticated
Antenna and 2 Parentheses
Blinking
Receiving Data
Not Present
No Radio Present
4 Bars
>80% Charged
3 Bars
60%-80% Charged
2 Bars
40%-60% Charged
1 Bar
20%-40% Charged
0 Bars
Low Battery
4 Blinking w/ Lightning Bolt
Charging >80% Capacity
3 Blinking w/ Lightning Bolt
Charging 60-80% Capacity
2 Blinking w/ Lightning Bolt
Charging 40-60% Capacity
1 Blinking w/ Lightning Bolt
Charging 20-40% Capacity
0 Bars w/ Lightning Bolt
Media cover open
Blinking
Receiving data
Solid
Charging <20% Capacity
Blinking
Ethernet Connected
Not Present
3, 6, 7, 8
10, 12
n/a
No Ethernet Connection
continued
45
QLn Series User Guide
Blinking
Data processing in
progress
Steady
No data being processed
Blinking
Out of Media
Steady
Media present
Blinking
Error exists (excluding
Media Out and Head
Latch Open)
Not Present
10,12
3,4,6,12
No error exists
4 Bars
802.11 signal strength
> 75%
3 Bars
802.11 signal strength
25%
1 Bar
802.11 signal strength

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : Yes
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.0-c321 44.398116, Tue Aug 04 2009 14:24:39
Modify Date                     : 2011:03:28 17:35:50-07:00
Create Date                     : 2011:03:09 16:00:55-08:00
Metadata Date                   : 2011:03:28 17:35:50-07:00
Creator Tool                    : Adobe InDesign CS4 (6.0.6)
Format                          : application/pdf
Document ID                     : uuid:6f405917-417e-4690-8b66-44971168945b
Instance ID                     : uuid:73111271-01db-4d9e-9000-0a1edf7ca6bf
Producer                        : Adobe PDF Library 9.0
Page Count                      : 41
Creator                         : Adobe InDesign CS4 (6.0.6)
EXIF Metadata provided by EXIF.tools
FCC ID Filing: I28MD-ZBR5QLN

Navigation menu