Zebra Technologies MD-ZLAN11G Zebra Embedded 802.11b/g Radio User Manual HC100 User Guide

Zebra Technologies Corporation Zebra Embedded 802.11b/g Radio HC100 User Guide

Contents

Host user manual

 HC100™Wristband PrinterUser Guide
© 2008 ZIH Corp.   The copyrights in this manual and the software and/or firmware in the printer described therein are owned by ZIH Corp. Unauthorized reproduction of this manual or the software and/or firmware in the printer may result in imprisonment of up to one year and fines of up to $10,000 (17 U.S.C.506). Copyright violators may be subject to civil liability.This product may contain ZPL®, ZPL II®, and ZebraLink™ programs; Element Energy Equalizer® Circuit; E3®; and Monotype Imaging fonts. Software © ZIH Corp. All rights reserved worldwide.ZebraLink and all product names and numbers are trademarks, and Zebra, the Zebra logo, ZPL, ZPL II, Element Energy Equalizer Circuit, and E3 Circuit are registered trademarks of ZIH Corp. All rights reserved worldwide.All other brand names, product names, or trademarks belong to their respective holders. For additional trademark information, please see “Trademarks” on the product CD.Proprietary Statement  This manual contains proprietary information of Zebra Corporation and its subsidiaries (“Zebra Technologies”). It is intended solely for the information and use of parties operating and maintaining the equipment described herein. Such proprietary information may not be used, reproduced, or disclosed to any other parties for any other purpose without the express, written permission of Zebra Technologies Corporation.Product Improvements  Continuous improvement of products is a policy of Zebra Technologies Corporation. All specifications and designs are subject to change without notice.Liability Disclaimer  Zebra Technologies Corporation takes steps to ensure that its published Engineering specifications and manuals are correct; however, errors do occur. Zebra Technologies Corporation reserves the right to correct any such errors and disclaims liability resulting therefrom.Limitation of Liability  In no event shall Zebra Technologies Corporation or anyone else involved in the creation, production, or delivery of the accompanying product (including hardware and software) be liable for any damages whatsoever (including, without limitation, consequential damages including loss of business profits, business interruption, or loss of business information) arising out of the use of, the results of use of, or inability to use such product, even if Zebra Technologies Corporation has been advised of the possibility of such damages. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.Part Number: 61207L-001 Rev. A
3Compliance Information4/23/08 HC100 User Guide 61207L-001 Rev. ADeclaration of ConformityI have determined that the Zebra printers identified as theHC100™manufactured by:Zebra Technologies Corporation333 Corporate Woods ParkwayVernon Hills, Illinois 60061-3109 U.S.A.Have been shown to comply with the applicable technical standards of the FCCFor Home, Office, Commercial, and Industrial useIf no unauthorized change is made in the equipment,and if the equipment is properly maintained and operated.
Compliance InformationFCC Compliance Statement461207L-001 Rev. A HC100 User Guide 4/23/08FCC Compliance StatementThis device complies with Part 15 rules. Operation is subject to the following two conditions:1. This device may not cause harmful interference, and2. This device must accept any interference received, including interference that may cause undesired operation.The user is cautioned that any changes or modifications not expressly approved by Zebra Technologies Corporation could void the user’s authority to operate the equipment. To ensure compliance, this printer must be used with Shielded Communication Cables.FCC Radiation Exposure Statement (for printers with internal radio devices)This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.FCC Rules and Regulations for Data CablesZebra printers comply with FCC Rules and Regulations, Part 15 for Class B Equipment using fully shielded, 6.5 ft. (2 m) data cables. Use of unshielded cables may increase radiation above the Class B limits. Canadian DOC Compliance StatementThis Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
4/23/08 HC100 User Guide 61207L-001 Rev. AContentsDeclaration of Conformity  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3FCC Compliance Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4FCC Radiation Exposure Statement (for printers with internal radio devices) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4FCC Rules and Regulations for Data Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4Canadian DOC Compliance Statement  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4About This Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Who Should Use This Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  10How This Document Is Organized  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  10Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11Web Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11The Americas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11Europe, Africa, Middle East, and India . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11Asia Pacific . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11Document Conventions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  121 • Introduction to the HC100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Front of Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  16Rear of Printer and Connectors  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  17Control Panel  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  18Control Panel Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  18Control Panel Buttons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  18
Contents661207L-001 Rev. A HC100 User Guide 4/23/08Media Cartridges and Wristbands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  20Media Cartridges  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  20Wristband Sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  21Wristband Colors  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  21Wristband Closure Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  22Wristband Print Zone  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  242 • Printer Setup  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25Handling the Printer  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  26Unpack and Inspect the Printer  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  26Store the Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  26Ship the Printer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  26Preparing the Printer for Use  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  27Site Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  27Connect to Data Communication Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  27Connect to Power Source and Turn on Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  29Insert Media Cartridge  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  313 • Troubleshooting   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33Media Status Indicator  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  34Printer Status Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  36Wireless Status Indicator  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  39Miscellaneous Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  404 • Routine Maintenance   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43Cleaning the Media Path. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  44Using a Cleaning Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  44Using a Swab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  45Cleaning the Smart Card Contacts and the Media Cartridge Sensor Pins . . . . . . . . . . . .  51Replacing Printer Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  53Ordering Replacement Parts  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  53Recycling Printer Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  53Lubrication  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  535 • Advanced User Information  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55Viewing Printer Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  56On a Printer Configuration Wristband. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  56Through the Printer’s Web Pages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  57Changing and Restoring Printer Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  58Setting, Changing, and Restoring Print Server Settings . . . . . . . . . . . . . . . . . . . . . . . . . .  66Connecting for the First Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  66Changing Parameters after Connecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  66Web Pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
7Contents4/23/08 HC100 User Guide 61207L-001 Rev. AAdditional Diagnostics Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  72Media Sensor Profile  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  72Communications Diagnostics Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  73Downloading Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  746 • Specifications   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75Physical and Environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  76Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  76Wristband . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  77Standard and Optional Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  77Power Cord. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  78End User License Agreement  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Contents861207L-001 Rev. A HC100 User Guide 4/23/08 Notes •  _____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
4/23/08 HC100 User Guide 61207L-001 Rev. AAbout This DocumentThis section provides you with contact information, document structure and organization, and additional reference documents.ContentsWho Should Use This Document. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  10How This Document Is Organized . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  10Contacts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  11Document Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  12
About This DocumentWho Should Use This Document1061207L-001 Rev. A HC100 User Guide 4/23/08Who Should Use This DocumentThis User Guide is intended for use by any person who needs to operate or to troubleshoot the printer. An additional section is included for advanced users or service technicians.How This Document Is OrganizedThe User Guide is set up as follows:Section DescriptionIntroduction to the HC100 on page 15 This section shows the printer components, indicator lights, and operational controls.Printer Setup on page 25 This section provides instructions for setting up the printer, connecting it to your network, and preparing it for use.Troubleshooting on page 33 This section includes the meaning of various printer status lights.Routine Maintenance on page 43 This section includes routine cleaning procedures and recycling information.Advanced User Information on page 55 This section contains information and instructions that are intended only for advanced users or service technicians.Specifications on page 75 This section contains the specifications for the printer and wristbands.
11About This DocumentContacts4/23/08 HC100 User Guide 61207L-001 Rev. AContactsYou can contact Zebra Technologies Corporation at the following:Web Sitehttp://www.zebra.comTechnical Support via the Internet is available 24 hours per day, 365 days per year. Go to http://www.zebra.com/support.The AmericasEurope, Africa, Middle East, and IndiaAsia PacificRegional Headquarters Technical Support Customer Service Dept.Zebra Technologies International, LLC333 Corporate Woods ParkwayVernon Hills, Illinois 60061.3109 U.S.AT: +1 847 793 2600Toll-free +1 800 423 0422F: +1 847 913 8766T: +1 877 ASK ZEBRA (275 9327)F: +1 847 913 2578Hardware: ts1@zebra.comSoftware: ts3@zebra.comFor printers, parts, media, and ribbon, please call your distributor, or contact us.T: +1 877 ASK ZEBRA (275 9327)E: clientcare@zebra.comRegional Headquarters Technical Support Internal Sales Dept.Zebra Technologies Europe LimitedZebra HouseThe Valley Centre, Gordon RoadHigh WycombeBuckinghamshire, HP13 6EQ, UKT: +44 (0)1494 472872F: +44 (0) 1494 450103T: +44 (0) 1494 768298F: +44 (0) 1494 768210Germany: Tsgermany@zebra.comFrance: Tsfrance@zebra.comSpain/Portugal: Tsspain@zebra.comAll other areas: Tseurope@zebra.comFor printers, parts, media, and ribbon, please call your distributor, or contact us.T: +44 (0) 1494 768316F: +44 (0) 1494 768244E: cseurope@zebra.comRegional Headquarters Technical Support Customer ServiceZebra Technologies Asia Pacific, LLC120 Robinson Road#06-01 Parakou BuildingSingapore 068913T: +65 6858 0722F: +65 6885 0838T: +65 6858 0722F: +65 6885 0838E: China: tschina@zebra.comAll other areas:tsasiapacific@zebra.comFor printers, parts, media, and ribbon, please call your distributor, or contact us.T: +65 6858 0722F: +65 6885 0836
About This DocumentDocument Conventions1261207L-001 Rev. A HC100 User Guide 4/23/08Document ConventionsThe following conventions are used throughout this document to convey certain information.Alternate Color  (online only) Cross-references contain hot links to other sections in this guide. If you are viewing this guide online in .pdf format, you can click the cross-reference (blue text) to jump directly to its location. Icons Used  Illustration Callouts  Callouts are used when an illustration contains information that needs to be labeled and described. A table that contains the labels and descriptions follows the graphic. Figure 1 provides an example.Figure 1 • Sample Figure with CalloutsCaution • Warns you of the potential for electrostatic discharge.Caution • Warns you of a situation where excessive heat could cause a burn.Caution • Advises you that failure to take or avoid a specific action could result in physical harm to you.Caution • (No icon) Advises you that failure to take or avoid a specific action could result in physical harm to the hardware.Important • Advises you of information that is essential to complete a task.Note •  Indicates neutral or positive information that emphasizes or supplements important points of the main text.1Eject button2Pause/Feed button12
13About This DocumentDocument Conventions4/23/08 HC100 User Guide 61207L-001 Rev. AControl Panel Lights  The printer status indicator uses green, yellow, and orange lights that sometimes blink or rotate to indicate the printer’s status and any error conditions. The lights and light sequences are indicated as follows:Lights On A solid, colored bar indicates when the printer status indicator is on.A solid bar that is divided into two colors indicates that half of the printer status indicator lights are on with one color while the other half of the lights are on with the other color.Lights Flashing or Blinking Alternating colors in a subdivided bar indicate that the lights on the printer status indicator are flashing or blinking.• one colored blink• two colored blinks• steady color on with two blinks off• three colored blinks• four colored blinks• consistent flashing on and off• flashing between two colors.Lights Rotating The printer status indicator lights can light up in a clockwise rotating sequence. Rotating lights that come on one at a time are indicated by a curved, broken arrow and a bar that shows the color of the lights.Rotating lights that stay on after lighting up are indicated by a curved, solid arrow and a bar that shows the color of the lights.
About This DocumentDocument Conventions1461207L-001 Rev. A HC100 User Guide 4/23/08 Notes •  _____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
4/23/08 HC100 User Guide 61207L-001 Rev. A1Introduction to the HC100This section shows the printer components, indicator lights, and operational controls.ContentsFront of Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  16Rear of Printer and Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  17Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Control Panel Lights. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  18Control Panel Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  18Media Cartridges and Wristbands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  20Media Cartridges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  20Wristband Sizes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  21Wristband Colors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  21Wristband Closure Type. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  22Wristband Print Zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  24
Introduction to the HC100Front of Printer1661207L-001 Rev. A HC100 User Guide 4/23/08Front of PrinterFigure 2 shows the front of the printer.Figure 2 • Front of Printer1Media cartridge slot2Upper cover3Upper cover release button (one on each side)4Control panel (see Control Panel on page 18)1324
17Introduction to the HC100Rear of Printer and Connectors4/23/08 HC100 User Guide 61207L-001 Rev. ARear of Printer and ConnectorsFigure 3 shows the data communication connectors on the rear of the printer, the power button, and the D/C power connector. For more information about the optional wired and wireless Ethernet print servers, see Connect to Data Communication Interfaces on page 27 and Changing and Restoring Printer Settings on page 58.Figure 3 • Rear of Printer1Serial port2Optional ZebraNet® 10/100 Internal Print Server (wired Ethernet) port3USB port4Power on/off button (in is On, out is Off)5D/C power connectorStandard and Optional WirelessOptional 10/100 Wired Ethernet12345
Introduction to the HC100Control Panel1861207L-001 Rev. A HC100 User Guide 4/23/08Control PanelThe control panel is located on the front of the printer. Control Panel LightsThe control panel has two basic lights that indicate the printer’s status and error conditions (Figure 4). Printers with the Wireless Ethernet Option have an additional status indicator light.Figure 4 • Control Panel LightsControl Panel ButtonsThe control panel has two buttons (Figure 5). Their function is described in Table 1. When you press or press and hold a button, the printer action occurs when you release the button.Figure 5 • Control Panel Buttons1Media status indicator (see Media Status Indicator on page 34)2Printer status indicator (outer ring) (see Printer Status Indicator on page 36)3Wireless status indicator (see Wireless Status Indicator on page 39)Standard and Optional 10/100 Wired Ethernet Optional Wireless1321EJECT button2PAUSE/FEED buttonStandard and Optional 10/100 Wired Ethernet Optional Wireless12
19Introduction to the HC100Control Panel4/23/08 HC100 User Guide 61207L-001 Rev. ATable 1 • Function of the Control Panel ButtonsButton Function/DescriptionEJECT This button functions only when the printer is idle or paused. The function depends on whether you press the button or press and hold it.•Pressing and releasing EJECT causes the printer to retract the current wristband and eject the media cartridge. •Pressing and holding EJECT for 6 seconds force ejects the media cartridge without retracting the protruding wristband. After a forced eject, press the upper cover release buttons to open the printer’s upper cover and release the wristband. See Media Cartridges on page 20 for information on removing the wristband from the cartridge. Do NOT pull the remainder of the wristband out of the cartridge. Note • If pressing EJECT does not eject the media cartridge, power cycle the printer and press EJECT again. Use the forced eject option only as a last resort if these other attempts fail. PAUSE/FEED PAUSE/FEED has different functions depending on whether the printer is idle or paused and on whether you press the button or press and hold it.•Pressing and releasing PAUSE/FEED has two functions.•Pause—PAUSE/FEED functions as a pause button when the printer is actively printing a wristband. While a wristband is printing, press the button to pause the printer before the next wristband starts printing. The printer remains paused until you press the button again.•Feed—PAUSE/FEED functions as a feed button when the printer is idle. Press the button to feed one blank wristband.•Pressing and holding PAUSE/FEED places the printer in user configuration mode. The printer status indicator lights blink orange in 2-second intervals, adding one blink each interval. Depending on when you release PAUSE/FEED, different actions take place:• One orange blink—A printer configuration wristband prints.• Two orange blinks—A media sensor profile prints.• Three orange blinks—The printer resets all print server parameters (wired Ethernet and wireless Ethernet) back to defaults. • Four orange blinks—The printer resets all printer parameters back to defaults.• After four orange blinks, the printer exits user configuration mode. The printer status lights return to solid green. The printer feeds a wristband when you release PAUSE/FEED.
Introduction to the HC100Media Cartridges and Wristbands2061207L-001 Rev. A HC100 User Guide 4/23/08Media Cartridges and WristbandsDifferent sizes, colors, and closure types of wristbands are available in recyclable media cartridges. This information appears on the media cartridge label. The wristbands feature an antimicrobial coating to help protect against the spread of S. aureus, P aeruginosa, E. coli, and MRSA. For ordering information, see Contacts on page 11. Only Genuine Zebra™ supplies will work with your printer.Media CartridgesView the level of media remaining in the cartridge through the wristband supply window on the left side of the media cartridge (Figure 6). Wristbands exit through a slot on the front of the media cartridge.Figure 6 • Media CartridgeMedia cartridges cannot be reused or refilled. Dispose of media cartridges in accordance with your local regulations or standards. For information on Zebra's recycling program, see http://www.zebra.com/environment.1Wristband supply window2Wristband exit areaImportant • Forcibly pulling a wristband from the media cartridge can damage the cartridge. A damaged cartridge will not work. If a wristband sticks out partially from a cartridge, use scissors to cut off the exposed part so that it is flush with the cartridge. Do NOT pull the remainder of the wristband out of the cartridge. The printer will eject the partial wristband after the cartridge loads properly.12
21Introduction to the HC100Media Cartridges and Wristbands4/23/08 HC100 User Guide 61207L-001 Rev. AWristband SizesThe size of the wristbands is indicated on the top of each media cartridge (Figure 7). A wristband should be snug enough to stay on the person’s wrist or ankle but not so tight that it cuts into the person’s skin or cuts off circulation.Figure 7 • Wristband Size IndicatorsWristband ColorsWristbands are available in seven colors for color-coding.Adult Pediatric InfantAdhesive Closure Type•Red•Blue•Yellow•Green•Pink• Purple•OrangeClip Closure Type•Red•Blue•Yellow• Green•Pink• Purple
Introduction to the HC100Media Cartridges and Wristbands2261207L-001 Rev. A HC100 User Guide 4/23/08Wristband Closure TypeZebra offers two types of wristband: adhesive closure and clip closure.Adhesive WristbandsZebra Z-Band™ Direct Wristbands are fastened with adhesives that are part of the wristband.Figure 8 • Adhesive Closure WristbandTo fasten an adhesive wristband, complete these steps:1. Remove the cover from the adhesive.2. Wrap the wristband around a person’s wrist or ankle, and then press the exposed adhesive to the wristband.Important • To keep the wristband from being too loose or too tight, place your finger between the wristband and the person’s wrist or ankle while fastening the wristband. Do not attempt to adjust the wristband after it is fastened. The tamper-evident slits under the adhesive tear if you try to remove the wristband.
23Introduction to the HC100Media Cartridges and Wristbands4/23/08 HC100 User Guide 61207L-001 Rev. AClip WristbandsZebra Z-Band™ QuickClip Wristbands are fastened with clips.Figure 9 • Clip Closure WristbandTo fasten a clip wristband, complete these steps:1. Insert the post on a clip through a hole on the wristband.2. Wrap the wristband around a person’s wrist or ankle, and then thread the post through the lone hole on the opposite end of the wristband. If necessary, move the clip to a different hole to resize the wristband.3. Fold the clip over, and press to lock it.XXXXX XXXXXXXXXXXXXXXXX XXXXXXXX XXX XXXXXXXXXXXXXXXXXXXXXX
Introduction to the HC100Media Cartridges and Wristbands2461207L-001 Rev. A HC100 User Guide 4/23/08Wristband Print ZoneThe best area for printing varies by wristband type. For best results, design your wristband formats so that they print in the recommended print zone of the wristband (Figure 10). Avoid printing over the clip holes (Z-Band QuickClip) or the tamper-evident slits (Z-Band Direct).Figure 10 • Media Home Position and Recommended Print ZoneZ-Band QuickClip12 3 4Z-Band Direct12 3 41Non-printable area(shown in red) You cannot print on approximately the first 1 inch (25.4 mm) of each wristband because the media does not backfeed into the printer.2Media home position The media home position (0,0) occurs 1 in. (25.4 mm) from the leading edge of the wristband.3Recommended print start position The start position from the leading edge of the wristband varies by wristband type (see Table 2).4Recommended print zone(shown in green) This area is recommended for printing because it is visible on the patient after the wristband is secured.Table 2 • Recommended Print Start Position by Label TypeWristband Type Wristband Length Start Position from the Leading EdgeZ-Band Direct  11 in. (279 mm) 4.5 in. (114 mm)7 in. (178 mm) 2.5 in. (64 mm)6 in. (152 mm) 2 in. (51 mm)Z-Band QuickClip 11 in. (279 mm) 6.25 in. (159 mm)7 in. (178 mm) 3.25 in. (83 mm)
4/23/08 HC100 User Guide 61207L-001 Rev. A2Printer SetupThis section provides instructions for setting up the printer, connecting it to your network, and preparing it for use.ContentsHandling the Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  26Unpack and Inspect the Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  26Store the Printer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  26Ship the Printer  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  26Preparing the Printer for Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  27Site Selection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  27Connect to Data Communication Interfaces  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  27Connect to Power Source and Turn on Power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  29Insert Media Cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  31
Printer SetupHandling the Printer2661207L-001 Rev. A HC100 User Guide 4/23/08Handling the PrinterThis section describes how to handle your printer.Unpack and Inspect the PrinterWhen you receive the printer, immediately unpack it and inspect for shipping damage. • Save all packing materials.• Check all exterior surfaces for damage.If you discover shipping damage upon inspection:• Immediately notify the shipping company and file a damage report.• Keep all packaging material for shipping company inspection.• Notify your authorized Zebra resellerStore the PrinterIf you are not placing the printer into immediate operation, repackage it using the original packing materials. You may store the printer under the conditions shown in Table 3.Ship the PrinterIf you must ship the printer:• Turn off (O) the printer, and disconnect all cables.• Remove any media cartridges from the printer.• Make sure that upper cover is closed.• Carefully pack the printer into the original container or a suitable alternate container to avoid damage during transit. A shipping container can be purchased from Zebra if the original packaging has been lost or destroyed.Important • Zebra Technologies Corporation is not responsible for any damage incurred during the shipment of the equipment and will not repair this damage under warranty.Table 3 • Storage Temperature and HumidityTemperature Relative Humidity–40°F to 140°F (–40° to 60°C) 5% to 85% non-condensing
27Printer SetupPreparing the Printer for Use4/23/08 HC100 User Guide 61207L-001 Rev. APreparing the Printer for UseTo prepare the printer for use, select an appropriate location for the printer, connect the appropriate cables to the printer, turn on the printer power, and then select and insert a media cartridge.Site SelectionSelect a solid, level surface within reach of an available power outlet. To allow for proper ventilation and cooling, leave open space on all sides of the printer.Connect to Data Communication InterfacesSelect a data communication interface that is supported by both your printer and your computer or your Local Area Network (LAN). You may send wristband formats to the printer through any of its data communication ports. Figure 11 shows the location of the data communication ports. Table 4 provides basic information about the data communication interfaces. Figure 11 • Data Communication PortsCaution •  Do not place any padding or cushioning material under the unit or next to the back of the unit. This can prevent proper cooling and cause the unit to overheat.1Serial port2Optional ZebraNet 10/100 Internal Print Server (wired Ethernet) port3USB portCaution • Be careful not to plug a USB cable into the optional 10/100 wired Ethernet port on the printer. Doing so will damage the connector. The 10/100 wired Ethernet port comes with a plastic plug to protect it from accidental damage.123
Printer SetupPreparing the Printer for Use2861207L-001 Rev. A HC100 User Guide 4/23/08Use of Shielded Data Cables   Ethernet cables do not require shielding, but all other data cables must be fully shielded and fitted with metal or metallized connector shells. Unshielded data cables may increase radiated emissions above the regulated limits. Table 4 • Characteristics of the Data Communication InterfacesInterface Standard or Optional CharacteristicsRS-232 Serial Standard • Maximum cable length of 50 ft (15.24 m).• You may need to change printer parameters to match the host computer. See Changing and Restoring Printer Settings on page 58.• You need to use a null-modem adaptor to connect to the printer if using a standard modem cable.USB Standard • Maximum cable length of 16.4 ft (5 m).• No printer parameter changes required to match the host computer.• Requires installation of a printer driver. The driver is available at http://www.zebra.com/drivers or on the user CD that came with your printer.ZebraNet 10/100 Internal Print Server (wired Ethernet)Optional • Can print to the printer from any computer on your LAN.• Can communicate with the printer through the printer’s web pages.• The printer must be configured to use your LAN. See Setting, Changing, and Restoring Print Server Settings on page 66.ZebraNet Internal Wireless Print Server (wireless Ethernet, 802.11b/g)Optional • Can print to the printer from any computer on your Wireless Local Area Network (WLAN) or LAN.• Can communicate with the printer through the printer’s web pages.• The printer must be configured to use your WLAN. See Setting, Changing, and Restoring Print Server Settings on page 66.
29Printer SetupPreparing the Printer for Use4/23/08 HC100 User Guide 61207L-001 Rev. AConnect to Power Source and Turn on PowerAfter you connect to a data communication interface, you may connect the printer to a power source and turn the power on.To connect the printer to a power source and turn on the power, complete these steps:1. Locate the two parts of the power cord assembly. The power cord assembly consists of an A/C power cord (1) and a low-voltage D/C cord that is attached to a power supply (2) (Zebra model number FSP070-RDBM). If an A/C power cord was not included with your printer, refer to Power Cord on page 78 for specifications.2. Insert the female end of the A/C power cord into the power supply.3. Insert the low-power D/C cord into the D/C power connector on the back of the printer.Caution • For personnel and equipment safety, always use an approved three-conductor power cord specific to the region or country intended for installation. This cord must use an IEC 320 female connector and the appropriate region-specific three-conductor grounded plug configuration.12
Printer SetupPreparing the Printer for Use3061207L-001 Rev. A HC100 User Guide 4/23/084. Plug the male end of the A/C power cord into an appropriate power outlet.5. Push the power button to turn on (I) the printer.The printer performs a self-test, and the control panel cycles through the light colors. The media status indicator and the printer status indicator blink orange to indicate that there is no media in the printer.115 V AC230 V AC
31Printer SetupPreparing the Printer for Use4/23/08 HC100 User Guide 61207L-001 Rev. AInsert Media CartridgeFor more information about media cartridges and wristbands, see Media Cartridges and Wristbands on page 20.To insert a media cartridge, complete these steps:1. Orient the cartridge and the printer as shown.2. Insert the cartridge into the printer, and then press down until the cartridge clicks.The printer prepares a wristband for printing. With a new cartridge, the printer status indicator (1) turns green, and the media status indicator (2) remains off. For other media conditions, see Media Status Indicator on page 34.1 2
Printer SetupPreparing the Printer for Use3261207L-001 Rev. A HC100 User Guide 4/23/08 Notes •  _____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
4/23/08 HC100 User Guide 61207L-001 Rev. A3TroubleshootingThis section includes the meaning of various printer status lights.ContentsMedia Status Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  34Printer Status Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  36Wireless Status Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  39Miscellaneous Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  40
TroubleshootingMedia Status Indicator3461207L-001 Rev. A HC100 User Guide 4/23/08Media Status IndicatorTable 5 shows how the media status indicator and printer status indicator display different media levels or media errors. For light sequences not included here, see Printer Status Indicator on page 36.Table 5 • Media Status Indicator LightsMedia Status Indicator/Printer Status Indicator Meaning/Action RequiredOff/Green The printer is ready to print. The media cartridge still contains a substantial number of wristbands. No action is required.Solid Orange/Green The media level is low in the media cartridge (usually 20 or fewer wristbands). The printer can still continue to print.To order replacement media cartridges, see Contacts on page 11.Blinking Orange/Blinking Orange A media error occurred.To resolve the problem, complete these steps:1. Push the Eject button, and then remove the media cartridge from the printer.2. Check the media cartridge for the level of media and for misfed wristbands.(continued on next page)
35TroubleshootingMedia Status Indicator4/23/08 HC100 User Guide 61207L-001 Rev. ABlinking Orange/Blinking Orange (continued from previous page)3. If the media cartridge is...Emptya. Dispose of or recycle the empty media cartridge according to your local ordinances.b. Insert a different media cartridge in the printer.Not emptya. Reinsert the media cartridge into the printer. b. If the error persists, clean the smart card on the media cartridge and the media cartridge sensor (see Cleaning the Smart Card Contacts and the Media Cartridge Sensor Pins on page 51). c. If the error reoccurs after cleaning, replace the media cartridge. d. If the error reoccurs with a different media cartridge, contact technical support (see Contacts on page 11). Not empty, but wristbands are protruding from the cartridge or jamming in the printerMedia is not loading correctly.a. Cut off the protruding part of the wristband. Do NOT pull the wristband out of the media cartridge, or you will damage the media cartridge.b. Reinsert the cartridge into the printer.c. If the error reoccurs, replace the media cartridge. d. If the error reoccurs with a different media cartridge, contact technical support (see Contacts on page 11).Table 5 • Media Status Indicator Lights (Continued)Media Status Indicator/Printer Status Indicator Meaning/Action Required
TroubleshootingPrinter Status Indicator3661207L-001 Rev. A HC100 User Guide 4/23/08Printer Status IndicatorIn alert and error conditions, the printer status indicator lights may be on, blinking, or rotating. Table 6 describes the different lights and light sequences. See Control Panel Lights on page 13 for information about how the light sequences are indicated.Table 6 • Lights and Light Sequences for Alert and Error ConditionsLight or Light Sequence Meaning Action RequiredSteady Green The printer is ready to print. NoneRotating Green The printer is downloading or processing data. None.Rotating Green Fill The printer is defragmenting or initializing flash memory. None.Steady Green, 2 Blinks Off The printer is paused. Press PAUSE/FEED to resume printing.Flashing Green then Orange The printer is in forced download mode. Download firmware to the printer, or power cycle the printer to return to regular printing mode.Steady Half-Orange, Half-Green The printer is writing to flash after a firmware download. None.Caution • Do not power cycle the printer during this phase. Doing so makes the printer inoperable.Steady Yellow A forced eject of the media cartridge is being initiated by pressing and holding EJECT. The printer will ultimately eject the media cartridge when the button is released, but it may be a forced eject or a normal eject.•To cancel the forced eject and eject the media cartridge normally, release EJECT before the printer status indicator blinks yellow. •To proceed with the forced eject, continue to hold EJECT (about 6 seconds) until the printer status indicator blinks yellow. After the forced eject, press the upper cover release buttons to open the printer’s upper cover and release the wristband. See Media Cartridges on page 20 for information on removing the wristband from the cartridge. Do NOT pull the remainder of the wristband out of the cartridge.
37TroubleshootingPrinter Status Indicator4/23/08 HC100 User Guide 61207L-001 Rev. AFlashing Yellow A forced eject of the media cartridge is pending. Release EJECT to allow the printer to force eject the media cartridge.Rotating Yellow Fill The printhead reached temperature fail safe mode. Caution • The printhead may be hot and could cause severe burns. Allow the printhead to cool.1. Turn the printer off (O).2. Wait for the printhead to cool.3. Turn the printer back on (I).4. If the problem persists, repeat steps 1 and 2 and then make sure that the printhead cables are connected properly.5. If the problem persists after checking the cables, contact technical support (see Contacts on page 11).Steady Orange If the color lasts for more than 3 seconds, one of the following conditions exists:• The printhead is too cold.• The printhead is too hot.• The platen motor is too hot.Wait a few minutes. If the platen motor is causing the problem, printing resumes when it cools.If printing does not resume, do the following:Caution • The printhead may be hot and could cause severe burns. Allow the printhead to cool.1. Turn the printer off (O).2. Wait for the printhead to cool. 3. Turn the printer back on (I).4. If the problem persists, repeat steps 1 and 2 and then make sure that the printhead cables are connected properly.5. If the problem persists after checking the cables, contact technical support (see Contacts on page 11).Table 6 • Lights and Light Sequences for Alert and Error Conditions (Continued)Light or Light Sequence Meaning Action Required
TroubleshootingPrinter Status Indicator3861207L-001 Rev. A HC100 User Guide 4/23/08Flashing Orange A media error occurred. See Media Status Indicator on page 34. The printer’s upper cover is open. Make sure that the upper cover is closed and latched. If the problem persists, contact technical support (see Contacts on page 11).Rotating Orange  A wristband was waiting to be removed when the printer tried to eject the media cartridge.Tear off the wristband that is hanging outside the printer before trying again to eject the media cartridge.Steady Orange, 2 Blinks Off The printer is paused because one of the following conditions exists:• The printer encountered an error while downloading a wristband format, a graphic, a font, or a bitmap.• The printer is out of memory.Press PAUSE/FEED to resume printing.Flashing Yellow then Orange PAUSE/FEED was pressed and held during printer power up. The printer can initiate forced download mode.Release PAUSE/FEED during the 3 seconds that these lights flash to enter forced download mode. If you hold PAUSE/FEED longer than 3 seconds, the printer boots up normally.Table 6 • Lights and Light Sequences for Alert and Error Conditions (Continued)Light or Light Sequence Meaning Action Required
39TroubleshootingWireless Status Indicator4/23/08 HC100 User Guide 61207L-001 Rev. AWireless Status IndicatorTable 7 describes the meaning of the wireless status indicator lights. For more information about the wireless print server, see the ZebraNet Wireless User Guide. A copy of this manual is available at http://www.zebra.com/manuals or on the user CD that came with your printer.Table 7 • Wireless Status Indicator LightsWireless Status Indicator MeaningSteady Green  The printer is associated with a wireless network. The signal strength is strong.Flashing Green  The printer is NOT associated with a wireless network. The signal strength is strong.Steady Orange The printer is associated with a wireless network. The signal strength is weak.Flashing Orange The printer is NOT associated with a wireless network. The signal strength is weak.
TroubleshootingMiscellaneous Troubleshooting4061207L-001 Rev. A HC100 User Guide 4/23/08Miscellaneous TroubleshootingTable 8 lists troubleshooting situations that are not necessarily shown by the status indicators.Table 8 • Miscellaneous TroubleshootingProblem Meaning/Action RequiredData is not printing on the first part of the wristband. You cannot print on the leading edge of each wristband. Redesign your wristband format so that it fits in the recommended print zone. See Wristband Print Zone on page 24.Data prints poorly on some sections of the wristband. Printing on uncoated areas, over holes, or over scores affects print quality.Redesign your wristband format so that it fits in the recommended print zone. See Wristband Print Zone on page 24.Wristbands will not load from a particular media cartridge. The printer is not detecting the media cartridge. Clean the smart card contacts on the media cartridge and the pins on the media cartridge sensor (see Cleaning the Smart Card Contacts and the Media Cartridge Sensor Pins on page 51). The media cartridge is damaged. This can occur if someone pulls a wristband out of the media cartridge.If you believe that the media cartridge was damaged when you received it, contact your authorized Zebra reseller. Otherwise, dispose of or recycle the media cartridge. To order replacement media cartridges, see Contacts on page 11.The media cartridge is refurbished. Only Genuine Zebra™ supplies will work with your printer.Dispose of or recycle the media cartridge. To order replacement media cartridges, see Contacts on page 11.Wristbands will not load from any media cartridge. The printer is not detecting the media cartridge. Clean the pins on the media cartridge sensor (see Cleaning the Smart Card Contacts and the Media Cartridge Sensor Pins on page 51). If the problem persists, have the printer repaired by a qualified service technician.Wristbands consistently jam or do not load correctly. The printer might not be detecting the black mark on the back of the wristbands.1. Replace the media cartridge.2. If the problem persists with a different media cartridge, have a qualified service technician check and possibly replace the media sensor.
41TroubleshootingMiscellaneous Troubleshooting4/23/08 HC100 User Guide 61207L-001 Rev. AThe printer will not eject the media cartridge. 1. Turn the printer off (O) and then back on (I).2. If the problem persists, initiate a forced eject.a. Press and hold EJECT for at least 6 seconds. The printer status indicator turns yellow after 2 seconds and flashes yellow after 6 seconds. b. Release EJECT after the printer status indicator flashes.c. Press the upper cover release buttons to open the printer’s upper cover and release the wristband.d. See Media Cartridges on page 20 for information on removing the wristband from the cartridge. Do NOT pull the remainder of the wristband out of the cartridge.e. Close the upper cover.3. If the problem persists, contact technical support (see Contacts on page 11).The printer overheats. Improper ventilation may be causing the printer to overheat.Check that the printer has open spaces on all sides. The printer should be on a flat, level surface. Do not place objects on top of the printer.Table 8 • Miscellaneous Troubleshooting (Continued)Problem Meaning/Action Required
TroubleshootingMiscellaneous Troubleshooting4261207L-001 Rev. A HC100 User Guide 4/23/08 Notes •  _____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
4/23/08 HC100 User Guide 61207L-001 Rev. A4Routine MaintenanceThis section includes routine cleaning procedures and recycling information.ContentsCleaning the Media Path . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  44Using a Cleaning Card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  44Using a Swab. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  45Cleaning the Smart Card Contacts and the Media Cartridge Sensor Pins  . . . . . . . . . . .  51Replacing Printer Components  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  53Ordering Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  53Recycling Printer Components  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  53Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  53
Routine MaintenanceCleaning the Media Path4461207L-001 Rev. A HC100 User Guide 4/23/08Cleaning the Media PathFor best results, clean the media path after each cartridge of media. You can clean the media path using a cleaning card or using a swab.Using a Cleaning CardFor cleaning cards, order part number 61097M. For ordering information, see Contacts on page 11.To clean the media path using a cleaning card, complete these steps:1. Press EJECT, and then remove the media cartridge from the printer.2. Turn off (O) the printer power.3. Remove the cleaning card from its packaging.4. Insert the cleaning card into the media chute as shown.5. Press and hold EJECT.6. Turn on (I) the printer power.7. Hold EJECT for approximately 15 seconds while the printer powers up and performs a self-test.8. Release EJECT when the cleaning card begins moving.The printer uses the cleaning card to clean the media path.
45Routine MaintenanceCleaning the Media Path4/23/08 HC100 User Guide 61207L-001 Rev. A9.10. Reinsert the media cartridge.Using a SwabUse the swab from a Preventive Maintenance Kit (part number 47362) or a clean swab dipped in a solution of isopropyl alcohol (minimum 90%) and deionized water (maximum 10%).To clean the media path using a swab, complete these steps:1. Press the Eject button, and remove the media cartridge from the printer.2. Turn off (O) the printer power.3. Press both upper cover release buttons simultaneously.The upper cover springs partially open.Caution • The cleaning card contains isopropyl alcohol, a flammable material. After use, discard according to your local regulations.Cleaning is complete when the card stops moving and returns to its original position.When cleaning is completed, remove and dispose of the cleaning card.Caution • Remove all rings, watches, hanging necklaces, identification badges, or other metallic objects that could touch the printhead or drop into the media cartridge slot.Caution • Before proceeding, discharge any built-up static electricity by touching the printer’s metal back plate near its power switch or by using an anti-static wriststrap and mat.
Routine MaintenanceCleaning the Media Path4661207L-001 Rev. A HC100 User Guide 4/23/084. Rotate the upper cover up and back.5. Caution • The printhead may be hot and could cause severe burns. Allow the printhead to cool.Grasp the metal lever plate on the printhead assembly and rotate the assembly upward to expose the printhead elements.
47Routine MaintenanceCleaning the Media Path4/23/08 HC100 User Guide 61207L-001 Rev. A6. Clean the printhead elements.a. Using the swab from the Preventive Maintenance Kit or a swab dipped in the alcohol solution, wipe along the brown strip on the printhead assembly from end to end.b. Allow the solution to evaporate.7. Clean the media guide surfaces.a. Using the swab, wipe the media chute surfaces. b. Allow the solution to evaporate.
Routine MaintenanceCleaning the Media Path4861207L-001 Rev. A HC100 User Guide 4/23/088. Rotate the two side clips on the platen roller upward.9. Remove the platen roller from the printer.10. Clean the platen roller.a. Using the swab, thoroughly clean the platen roller.b. Allow the solution to evaporate.
49Routine MaintenanceCleaning the Media Path4/23/08 HC100 User Guide 61207L-001 Rev. A11. Place the platen roller back into its place in the printer. 12. Secure the platen roller by rotating the two side clips back into place.13. Align the snap tabs on the bottom of the media chute with the slots in the printer chassis.
Routine MaintenanceCleaning the Media Path5061207L-001 Rev. A HC100 User Guide 4/23/0814. Press down on the metal lever plate to snap the printhead assembly back into place. 15. Close the upper cover.16. Turn on (I) the printer power.17. Reinsert the media cartridge.18. Discard the used swab.
51Routine MaintenanceCleaning the Smart Card Contacts and the Media Cartridge Sensor Pins4/23/08 HC100 User Guide 61207L-001 Rev. ACleaning the Smart Card Contacts and the Media Cartridge Sensor PinsAfter every five media cartridges, clean the media cartridge sensor pins to ensure that they make good contact with the smart card contacts on the media cartridge. If the printer will not detect a media cartridge, cleaning the media cartridge sensor pins and the smart card contacts on the cartridge may correct the problem. Use the swab from a Preventive Maintenance Kit (part number 47362) or a clean swab dipped in a solution of isopropyl alcohol (minimum 90%) and deionized water (maximum 10%).To clean the smart card contacts and the media cartridge sensor pins, complete these steps:1. Press the Eject button, and remove the media cartridge from the printer.2. Turn off (O) the printer power.3. Disconnect the low-power D/C cord from the D/C power connector on the back of the printer.4. Using the swab from the Preventive Maintenance Kit or a swab dipped in the alcohol solution, clean the gold smart card contacts on the back of the media cartridge. Allow the solution to evaporate.Caution • Remove all rings, watches, hanging necklaces, identification badges, or other metallic objects that could touch the printhead or drop into the media cartridge slot.Caution • Before proceeding, discharge any built-up static electricity by touching the printer’s metal back plate near its power switch or by using an anti-static wriststrap and mat.
Routine MaintenanceCleaning the Smart Card Contacts and the Media Cartridge Sensor Pins5261207L-001 Rev. A HC100 User Guide 4/23/085.6. Insert the low-power D/C cord into the D/C power connector on the back of the printer.7. Turn on (I) the printer power.8. Reinsert the media cartridge.9. Discard the used swab.Caution • Use only vertical strokes to clean the media cartridge sensor pins. Using horizontal strokes could damage the pins.Clean the media cartridge sensor pins.a. Using the swab and vertical strokes, clean the gold media cartridge sensor pins, which are visible at the back of the media cartridge slot.b. Allow the solution to evaporate.
53Routine MaintenanceReplacing Printer Components4/23/08 HC100 User Guide 61207L-001 Rev. AReplacing Printer ComponentsSome printer components, such as the printhead and platen roller, may wear out over time and can be replaced easily. Regular cleaning may extend the life of some of these components.Ordering Replacement PartsFor optimal printing quality and proper printer performance across our product line, Zebra strongly recommends the use of Genuine Zebra™ supplies as part of the total solution. Contact your authorized Zebra reseller for part ordering information, or see Contacts on page 11 for contact addresses and telephone numbers.Recycling Printer ComponentsLubricationNo lubrication is needed for this printer.The majority of this printer’s components are recyclable. Do not dispose of any printer components in unsorted municipal waste. Please recycle the printer components according to your local standards. For more information, see http://www.zebra.com/environment.Caution • Some commercially available lubricants will damage the finish and the mechanical parts if used on this printer.
Routine MaintenanceLubrication5461207L-001 Rev. A HC100 User Guide 4/23/08 Notes •  _____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
4/23/08 HC100 User Guide 61207L-001 Rev. A5Advanced User InformationThis section contains information and instructions that are intended only for advanced users or service technicians.ContentsViewing Printer Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  56On a Printer Configuration Wristband  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  56Through the Printer’s Web Pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  57Changing and Restoring Printer Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  58Setting, Changing, and Restoring Print Server Settings  . . . . . . . . . . . . . . . . . . . . . . . . .  66Connecting for the First Time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  66Changing Parameters after Connecting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  66Web Pages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70Additional Diagnostics Tools  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  72Media Sensor Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  72Communications Diagnostics Test. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  73Downloading Firmware  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  74
Advanced User InformationViewing Printer Settings5661207L-001 Rev. A HC100 User Guide 4/23/08Viewing Printer SettingsThe printer configuration wristband provides some basic information about the printer, particularly about the connectivity settings. If your printer has an active Ethernet wired or wireless connection, you can view all of the printer’s settings through the printer’s web pages.On a Printer Configuration WristbandA printer configuration wristband (Figure 12) shows the printer’s connectivity settings and the wristband tear-off position. The IP ADDRESS and MAC ADDRESS fields will have values only if a wired or wireless print server is active. The USB COMM field shows if the printer is connected to a computer via the USB connector.Figure 12 • Sample Printer Configuration WristbandTo print a printer configuration wristband, complete these steps:1. Make sure that the printer is on (I) and ready to print.2. Press and hold PAUSE/FEED until the green lights turn off on the printer status indicator and the orange lights blink once.3. Release PAUSE/FEED.A printer configuration wristband prints.
57Advanced User InformationViewing Printer Settings4/23/08 HC100 User Guide 61207L-001 Rev. AThrough the Printer’s Web PagesThe View Printer Configuration web page is shown in Figure 13. You can access this page for your printer by clicking View Printer Configuration on the printer home page. For more information about the web pages, see Web Pages on page 70.Figure 13 • View Printer Configuration Web Page (Printer Default Values Shown)Important • If you select the Print on Label option, a printer configuration wristband prints (see Figure 12 on page 56).
Advanced User InformationChanging and Restoring Printer Settings5861207L-001 Rev. A HC100 User Guide 4/23/08Changing and Restoring Printer SettingsBy default, the printer automatically adjusts the settings based on the type of media cartridge that you insert. You will not usually need to adjust these settings. If necessary, you can adjust the printer settings to obtain optimal print quality or to change connectivity parameters. You do this through Zebra Programming Language II (ZPL II) commands, Set/Get/Do (SGD) commands, or through the printer’s web pages. The printer requires an active wired or wireless Ethernet connection for you to access the printer’s web pages.For the ZPL commands and SGD commands, see the ZPL II Programming Guide. A copy of this manual is available at http://www.zebra.com/manuals or on the user CD that came with your printer. For instructions on accessing the printer’s web pages, see Web Pages on page 70.Table 9 shows the printer parameters and what you can use to modify them.Table 9 • Printer ParametersParameter DetailsDARKNESS MODE  Select Darkness ModeThe printer has three darkness modes, which determine how the DARKNESS value is set.Default Value: CARTRIDGE Selections: • CARTRIDGE—DARKNESS is set to the media cartridge default value. No changes are allowed, and the printer ignores ZPL commands that change the darkness value.• USER—DARKNESS is set by the user, and the printer ignores the media cartridge default value. This darkness value is used for all media cartridges that are inserted into the printer.• RELATIVE—DARKNESS is stored as the difference between the current darkness setting and the current media cartridge default value. The printer adds this difference to the default darkness value of any subsequent media cartridges.Corresponding ZPL Command: NoneCorresponding SGD Command: media.darkness_mode Located on Web Page: General Setup
59Advanced User InformationChanging and Restoring Printer Settings4/23/08 HC100 User Guide 61207L-001 Rev. ADARKNESS Adjust Print DarknessChange the darkness setting if the wristbands print too light or too dark.Important • To ensure the best image durability, set the darkness to the highest setting that provides good print quality and bar codes that scan consistently. If the darkness is set too high, bar codes may not scan, or the printhead may wear prematurely.Default Value: This value varies depending on the darkness mode and the media cartridge being used. Typically, the value is +21.Corresponding ZPL Command: ~SD, ^MD (available when the darkness mode is set to USER or RELATIVE; ignored when the darkness mode is set to CARTRIDGE)Corresponding SGD Command: NoneLocated on Web Page: General SetupPRINT WIDTH  Set Print WidthThis parameter is set automatically by the printer cartridge. It cannot be modified. The ^PW ZPL II command is ignored.Located on Web Page: Media Setup (view only)TEAR OFF  Adjust the Tear-Off PositionThis parameter adjusts the resting position of the wristband after printing. Higher numbers move the wristband farther out of the printer while lower numbers move the wristband farther inside the printer.Default Value: +0Range: +0 to +120Corresponding ZPL Command: ^TA Corresponding SGD Command: NoneLocated on Web Page: General SetupLABEL LENGTH Set Wristband LengthThis parameter is set automatically by the printer cartridge. It cannot be modified. The ^LL ZPL II command is ignored.MAXIMUM LENGTH  Set Maximum Wristband LengthThis parameter is set automatically by the printer cartridge. It cannot be modified. The ^ML ZPL II command is ignored.Located on Web Page: Media Setup (view only)SERIAL Set Serial CommunicationsSelect the communications port that matches the one being used by the host computer. This setting applies only when the serial port is used. Default Value: RS232Selections: RS232, RS485 MULTIDROPCorresponding ZPL Command: ^SC Corresponding SGD Command: NoneLocated on Web Page: Serial Communications SetupTable 9 • Printer Parameters (Continued)Parameter Details
Advanced User InformationChanging and Restoring Printer Settings6061207L-001 Rev. A HC100 User Guide 4/23/08BAUD Set BaudThis setting applies only when the serial port is used. The baud setting of the printer must match the baud setting of the host computer for accurate communications to take place. Select the value that matches the one being used by the host computer.Default Value: 9600Selections: 300, 600, 1200, 2400, 4800, 9600, 14400, 19200, 28800, 38400, 57600, 115200Corresponding ZPL Command: ^SC Corresponding SGD Command: NoneLocated on Web Page: Serial Communications SetupDATA BITS  Set Data BitsThis setting applies only when the serial port is used. The data bits of the printer must match the data bits of the host computer for accurate communications to take place. Set the data bits to match the setting being used by the host computer.Default Value: 8BITSSelections: 7BITS, 8BITSCorresponding ZPL Command: ^SC Corresponding SGD Command: NoneLocated on Web Page: Serial Communications SetupPARITY Set ParityThis setting applies only when the serial port is used. The parity of the printer must match the parity of the host computer for accurate communications to take place. Select the parity that matches the one being used by the host computer.Default Value: NONESelections: EVEN, ODD, NONECorresponding ZPL Command: ^SC Corresponding SGD Command: NoneLocated on Web Page: Serial Communications SetupHOST HANDSHAKE  Set Host HandshakeThis setting applies only when the serial port is used. The handshake protocol of the printer must match the handshake protocol of the host computer for communication to take place. Select the handshake protocol that matches the one being used by the host computer.Default Value: XON/XOFFSelections: XON/XOFF, DSR/DTR, RTS/CTSCorresponding ZPL Command: ^SC Corresponding SGD Command: NoneLocated on Web Page: Serial Communications SetupTable 9 • Printer Parameters (Continued)Parameter Details
61Advanced User InformationChanging and Restoring Printer Settings4/23/08 HC100 User Guide 61207L-001 Rev. APROTOCOL Set ProtocolProtocol is a type of error checking system. Depending on the selection, an indicator may be sent from the printer to the host computer signifying that data has been received. Select the protocol that is requested by the host computer. Further details on protocol can be found in the ZPL II Programming Guide.Default Value: NONESelections: NONE, ZEBRA, ACK_NAKCorresponding ZPL Command: ^SC Corresponding SGD Command: NoneLocated on Web Page: Serial Communications SetupNETWORK ID  Set Network IDThis parameter assigns a unique number to the printer when the printer is operating in an RS422/485 multi-drop network environment (an external RS422/485 adapter is required). This gives the host computer the means to address a specific printer. This does not affect TCP/IP or IPX networks.Default Value: 000Range: 000 to 999Corresponding ZPL Command: ^NI Corresponding SGD Command: NoneLocated on Web Page: Serial Communications SetupCOMMUNICATIONS Set Communications Diagnostics ModeThe communication diagnostics mode is a troubleshooting tool for checking the interconnection between the printer and the host computer. For more information, see Communications Diagnostics Test on page 73. Default Value: NORMAL MODESelections: NORMAL MODE, DIAGNOSTICSCorresponding ZPL Command: ~JD to start, ~JE to stopCorresponding SGD Command: NoneLocated on Web Page: NoneCONTROL PREFIX  Set Control Prefix CharacterThe printer looks for this two-digit hex character to indicate the start of a ZPL/ZPL II control instruction.Note • Do not use the same hex value for the control, format, and delimiter character. The printer must see different characters to work properly.Default Value: 7E ~Range: 00 to FFCorresponding ZPL Command: ^CT or ~CTCorresponding SGD Command: NoneLocated on Web Page: ZPL ControlTable 9 • Printer Parameters (Continued)Parameter Details
Advanced User InformationChanging and Restoring Printer Settings6261207L-001 Rev. A HC100 User Guide 4/23/08FORMAT PREFIX  Set Format Prefix CharacterThe format prefix is a two-digit hex value used as a parameter place marker in ZPL/ZPL II format instructions. The printer looks for this hex character to indicate the start of a ZPL/ZPL II format instruction. See the ZPL II Programming Guide for more information.Note • Do not use the same hex value for the control, format, and delimiter character. The printer must see different characters to work properly.Default Value: 5E ^Range: 00 to FFCorresponding ZPL Command: ^CC or ~CCCorresponding SGD Command: NoneLocated on Web Page: ZPL ControlDELIMITER CHAR  Set Delimiter CharacterThe delimiter character is a two-digit hex value used as a parameter place marker in ZPL/ZPL II format instructions. See the ZPL II Programming Guide for more information.Note • Do not use the same hex value for the control, format, and delimiter character. The printer must see different characters to work properly.Default Value: 2C ,Range: 00 to FFCorresponding ZPL Command: ^CD or ~CDCorresponding SGD Command: NoneLocated on Web Page: ZPL ControlZPL MODE  Select ZPL ModeThe printer remains in the selected mode until it is changed by this parameter or by using a ZPL/ZPL II command. The printer accepts wristband formats written in either ZPL or ZPL II, eliminating the need to rewrite any ZPL formats that already exist.Default Value: ZPL IIRange: ZPL II, ZPLCorresponding ZPL Command: ^SZ Corresponding SGD Command: NoneLocated on Web Page: ZPL ControlTable 9 • Printer Parameters (Continued)Parameter Details
63Advanced User InformationChanging and Restoring Printer Settings4/23/08 HC100 User Guide 61207L-001 Rev. ALABEL TOP  Adjust Top PositionThis parameter adjusts the print position vertically on the wristband. Positive numbers adjust the top position farther down the wristband (away from the printhead) by the specified number of dots. Negative numbers adjust the top position up the wristband (toward the printhead).Default Value: +000Range: +000 to +120 dotsCorresponding ZPL Command: ^LT Corresponding SGD Command: NoneLocated on Web Page: General SetupLEFT POSITION  Adjust Left PositionThis parameter adjusts the print position horizontally on the wristband. Positive numbers adjust printing to the left by the specified number of dots. Negative numbers shift printing to the right.Default Value: 0000Range: –9999 to +9999 dotsCorresponding ZPL Command: ^LS Corresponding SGD Command: NoneLocated on Web Page: Advanced SetupREPRINT MODE  Enable Reprint ModeWhen reprint mode is enabled, the printer reprints the last wristband after you correct an error condition.Default Value: DISABLEDSelections: ENABLED, DISABLEDCorresponding ZPL Command: ^JZ Corresponding SGD Command: NoneLocated on Web Page: NoneZBI Run ZBI 2.0If your printer was not factory-enabled with ZBI 2.0, you must purchase a ZBI 2.0 Activation Key to use ZBI 2.0. Contact your authorized Zebra reseller for more information.Default Value: STOPPED (DISABLED)Selections: STARTED (ENABLED), STOPPED (DISABLED)Corresponding ZPL Command: ^JI or ~JI to start, ~JQ to stopCorresponding SGD Command: zbi.control.run to start, zbi.control.terminate to stopLocated on Web Page: NoneTable 9 • Printer Parameters (Continued)Parameter Details
Advanced User InformationChanging and Restoring Printer Settings6461207L-001 Rev. A HC100 User Guide 4/23/08FORMAT CONVERT  Select Format ConvertSelects the bitmap scaling factor. The first number is the original dots per inch (dpi) value; the second, the dpi to which you would like to scale.Default Value: NONESelections: NONE, 150 → 300, 150 → 600, 200 → 600, 300 → 600Corresponding ZPL Command: ^MU Corresponding SGD Command: NoneLocated on Web Page: Advanced SetupNONRESET CNTR  View Non-Resettable CounterThis parameter displays the total length of media that the printer has printed. You can use ZPL commands to change the unit of measure for this counter.Corresponding ZPL Command: ~HQ to view, ^MU to change unit of measureCorresponding SGD Command: odometer.total_print_length Located on Web Page: NoneRESET CNTR1  View User-Controlled Counter 1This parameter displays the total length of media that the printer has printed since this parameter was last reset. You can use ZPL commands to change the unit of measure and reset this counter. Corresponding ZPL Command: ~HQ to view, ~RO to reset, ^MU to change unit of measureCorresponding SGD Command: odometer.media_marker_count1 Located on Web Page: NoneRESET CNTR2  View User-Controlled Counter 2This parameter displays the total length of media that the printer has printed since this parameter was last reset. You can use ZPL commands to change the unit of measure and reset this counter. Corresponding ZPL Command: ~HQ to view, ~RO to reset, ^MU to change unit of measureCorresponding SGD Command: odometer.media_marker_count2 Located on Web Page: NoneTable 9 • Printer Parameters (Continued)Parameter Details
65Advanced User InformationChanging and Restoring Printer Settings4/23/08 HC100 User Guide 61207L-001 Rev. ALOAD DEFAULTS Restore Printer Default ValuesRestores all parameters other than the network settings back to the factory defaults. Use care when loading defaults because you will need to reload all settings that you changed manually.Note • Loading factory defaults causes the printer to auto-calibrate.Corresponding ZPL Command: ^JUF Corresponding SGD Command: NoneLocated on Web Page: View and Modify Printer Settings (Restore Default Configuration button)To restore printer default values through the control panel, complete these steps:1. Press and hold PAUSE/FEED to place the printer in user configuration mode. The printer status indicator blinks orange. Depending on when you release PAUSE/FEED, different actions take place.2. Release PAUSE/FEED after the orange light blinks four times.The printer resets all printer parameters back to defaults. The default values are shown in Figure 13 on page 57.Table 9 • Printer Parameters (Continued)Parameter Details
Advanced User InformationSetting, Changing, and Restoring Print Server Settings6661207L-001 Rev. A HC100 User Guide 4/23/08Setting, Changing, and Restoring Print Server SettingsYour printer may include an optional ZebraNet 10/100 Internal Print Server (wired Ethernet) or a ZebraNet Internal Wireless Plus Print Server (wireless Ethernet).For additional information, refer to the manuals for your wired or wireless print server. Copies of the manuals are available at http://www.zebra.com/manuals or on the user CD that came with your printer. For instructions on accessing the printer’s web pages, see Web Pages on page 70.Connecting for the First TimeZebraNet 10/100 Internal Print Server  To configure the 10/100 Internal Print Server, connect the printer to your Local Area Network (LAN) using an Ethernet cable. By default, the printer is set for dynamic IP resolution, so it should acquire an IP address. Print a printer configuration wristband to find the printer’s IP address (see Viewing Printer Settings on page 56). If you need to change parameters before you can connect the first time, use the serial or USB port to send the appropriate ZPL or SGD commands.Zebranet Internal Wireless Print Server  See the ZebraNet Wireless User Guide for configuration instructions. Before you can connect your printer to your Wireless Local Area Network (WLAN) or view the printer’s web pages, you need to set the printer’s parameters to match your WLAN. Use the serial or USB port to send the appropriate instructions to the printer.After the printer connects to your WLAN, you can access the printer’s web pages to make changes to the settings. Print a printer configuration wristband to find the printer’s IP address (see Viewing Printer Settings on page 56).Changing Parameters after ConnectingTable 9 shows basic print server parameters and what you can use to modify them. For all other print server parameters, refer to the manuals for your wired or wireless print server.Table 10 • Print Server ParametersParameter DetailsIP ADDRESS View or Change the Printer’s IP AddressThis parameter can be modified only when PERMANENT is selected for IP PROTOCOL.Selections: 0 to 255 for each fieldDefault Value: 0.0.0.0 Note • Leading zeroes are not shown in the address.Corresponding ZPL Command: ^ND, ^NS (wired), or ^WI (wireless)Corresponding SGD Command: internal_wired.ip.addr (wired) or wlan.ip.addr (wireless)Located on Web Page: TCP/IP Settings
67Advanced User InformationSetting, Changing, and Restoring Print Server Settings4/23/08 HC100 User Guide 61207L-001 Rev. AIP PROTOCOL Select the Method to Obtain an IP AddressThis parameter tells if the user (permanent) or the server (dynamic) selects the IP address. If a dynamic option is chosen, this parameter tells the method by which the print server (wired or wireless) receives the IP address from the server.Selections: ALL, BOOTP, DHCP, DHCP AND BOOTP, PERMANENTDefault Value: AllCorresponding ZPL Command: ^ND, ^NS (wired), or ^WI (wireless)Corresponding SGD Command: internal_wired.ip.protocol (wired) or wlan.ip.protocol (wireless)Located on Web Page: TCP/IP SettingsSUBNET MASK View or Change the SubnetThis parameter can be modified only when PERMANENT is selected for IP PROTOCOL.Selections: 0 to 255 for each fieldDefault Value: 255.255.255.0 Note • Leading zeroes are not shown in the address.Corresponding ZPL Command: ^ND, ^NS (wired), or ^WI (wireless)Corresponding SGD Command: internal_wired.ip.netmask (wired) or wlan.ip.netmask (wireless)Located on Web Page: TCP/IP SettingsDEFAULT GATEWAY View or Change the GatewayThis parameter can be modified only when PERMANENT is selected for IP PROTOCOL.Selections: 0 to 255 for each fieldDefault Value: 0.0.0.0 Note • Leading zeroes are not shown in the address.Corresponding ZPL Command: ^ND, ^NS (wired), or ^WI (wireless)Corresponding SGD Command: internal_wired.ip.gateway (wired) or wlan.ip.gateway (wireless)Located on Web Page: TCP/IP SettingsTable 10 • Print Server Parameters (Continued)Parameter Details
Advanced User InformationSetting, Changing, and Restoring Print Server Settings6861207L-001 Rev. A HC100 User Guide 4/23/08IP PROTOCOL Select the Method to Obtain an IP AddressThis parameter tells if the user (permanent) or the server (dynamic) selects the IP address. If a dynamic option is chosen, this parameter tells the method by which the print server (wired or wireless) receives the IP address from the server.Selections: ALL, BOOTP, DHCP, DHCP AND BOOTP, PERMANENTDefault Value: AllCorresponding ZPL Command: ^ND, ^NS (wired), or ^WI (wireless)Corresponding SGD Command: internal_wired.ip.protocol (wired) or wlan.ip.protocol (wireless)Located on Web Page: TCP/IP SettingsSUBNET MASK View or Change the SubnetThis parameter can be modified only when PERMANENT is selected for IP PROTOCOL.Selections: 0 to 255 for each fieldDefault Value: 255.255.255.0 Note • Leading zeroes are not shown in the address.Corresponding ZPL Command: ^ND, ^NS (wired), or ^WI (wireless)Corresponding SGD Command: internal_wired.ip.netmask (wired) or wlan.ip.netmask (wireless)Located on Web Page: TCP/IP SettingsDEFAULT GATEWAY View or Change the GatewayThis parameter can be modified only when PERMANENT is selected for IP PROTOCOL.Selections: 0 to 255 for each fieldDefault Value: 0.0.0.0 Note • Leading zeroes are not shown in the address.Corresponding ZPL Command: ^ND, ^NS (wired), or ^WI (wireless)Corresponding SGD Command: internal_wired.ip.gateway (wired) or wlan.ip.gateway (wireless)Located on Web Page: TCP/IP SettingsTable 10 • Print Server Parameters (Continued)Parameter Details
69Advanced User InformationSetting, Changing, and Restoring Print Server Settings4/23/08 HC100 User Guide 61207L-001 Rev. ADEFAULT NET Restore Print Server Default ValuesRestores the wired and wireless network settings back to factory defaults.Corresponding ZPL Command: ^JUN Corresponding SGD Command: noneLocated on Web Page: View and Modify Printer Settings (Restore Default Network Configuration button)To restore printer default values through the control panel, complete these steps:1. Press and hold PAUSE/FEED to place the printer in user configuration mode.The printer status indicator blinks orange. Depending on when you release PAUSE/FEED, different actions take place.2. Release PAUSE/FEED after the orange light blinks three times.The printer resets all print server parameters back to defaults.Table 10 • Print Server Parameters (Continued)Parameter Details
Advanced User InformationWeb Pages7061207L-001 Rev. A HC100 User Guide 4/23/08Web PagesIf your printer has an active Ethernet wired or wireless connection, you can view and modify the printer’s settings through the printer’s web pages. For additional information, refer to the manuals for your wired or wireless print server. Copies of the manuals are available at http://www.zebra.com/manuals or on the user CD that came with your printer.The printer home page is shown in Figure 14.Figure 14 • Printer Home PageTo access printer settings through the web pages, complete these steps:1. On the printer home page, click View and Modify Printer Settings.The printer prompts for a password.2. Enter the password for your printer. The default password is 1234.3. Click Submit Changes.The following statement appears:Access Granted. This IP Address now has admin access to the restricted printer pages. Please Click here to proceed
71Advanced User InformationWeb Pages4/23/08 HC100 User Guide 61207L-001 Rev. A4. Click on the statement.The View and Modify Printer Settings page displays.5. Modify the settings as needed.For additional information, refer to the manuals for your wired or wireless print server. Copies of the manuals are available at http://www.zebra.com/manuals or on the user CD that came with your printer.
Advanced User InformationAdditional Diagnostics Tools7261207L-001 Rev. A HC100 User Guide 4/23/08Additional Diagnostics ToolsThe media sensor profile and the communications diagnostics test are available as diagnostic tools.Media Sensor ProfileUse the media sensor profile to troubleshoot the following types of problems:• If the media sensor experiences difficulty in determining where wristbands start and stop.• If the media sensor incorrectly identifies a preprinted area on a wristband as the end of the wristband.The media sensor readings are shown as peaks and flat areas on the media sensor profile (Figure 15). Two peaks appear when the sensors are operating properly, indicating that the sensors correctly detected the black mark on the back of the wristband. A media sensor profile prints on two wristbands.Figure 15 • Media Sensor ProfileTo print a media sensor profile, complete these steps:1. Make sure that the printer is on (I) and ready to print.2. Press and hold PAUSE/FEED until the green lights turn off on the printer status indicator and the orange lights blink once. Continue holding PAUSE/FEED until the orange lights blink twice.3. Release PAUSE/FEED.A media sensor profile prints.MEDIA MEDIA MEDIA MEDIA MEDIA MEDIA MEDIA MEDIA MEDIA MEDIA MEDIA MEDIA MEDIA MEDIA MEDIA MEDIA MEDIA MEDIA MEDIA MEDIA MEDI IA MEDIA MEDIA MEDIA MEDIA MEDIA MEDIA MEDIA MEDIA MEDIA MEDIA MEDIA100806040200
73Advanced User InformationAdditional Diagnostics Tools4/23/08 HC100 User Guide 61207L-001 Rev. ACommunications Diagnostics TestThe communication diagnostics test is a troubleshooting tool for checking the interconnection between the printer and the host computer.When the printer is in diagnostics mode, it prints all data received from the host computer as straight ASCII characters with the hex values below the ASCII text. The printer prints all characters received, including control codes such as CR (carriage return). Figure 16 shows a typical printout from this test. The actual format is modified to print on narrow wristbands.Figure 16 • Communications Diagnostics Test PrintoutTo use communications diagnostics mode, complete these steps:1. Set the printer to Diagnostics mode by sending the ~JD ZPL II command to the printer.The printer enters Diagnostics mode and prints any data received from the host computer on a test printout2. Check the test printout for error codes. For any errors, check that your communication parameters are correct. Errors show on the test printout as follows:• FE indicates a framing error.• OE indicates an overrun error.• PE indicates a parity error.• NE indicates noise.3. Send the ~JE ZPL II command to the printer to return to normal operation.Note • The PAUSE/FEED button will not advance a wristband while the printer is in Diagnostics mode. Exit Diagnostics mode to use that button and feed a wristband.
Advanced User InformationDownloading Firmware7461207L-001 Rev. A HC100 User Guide 4/23/08Downloading FirmwareZebra periodically issues updated firmware to enhance the usability of its printers. You may download the latest HC100 firmware to the printer at any time. For the latest firmware version and instructions for downloading it, go to http://www.zebra.com/firmware.You may choose to place the printer in forced download mode before downloading firmware. While in this mode, the printer does not accept wristband printing instructions or control panel button presses. To place the printer in forced download mode, complete these steps:1. Turn the printer off (O).2. Press and hold PAUSE/FEED while turning on the printer (I).During the printer self test, the printer status indicator rapidly alternates between yellow and orange for 3 seconds. 3. Release PAUSE/FEED during this light sequence to enter forced download mode.The printer status indicator alternates between green and orange lights. 4. Download firmware to the printer using any available connection.As firmware is downloading, a green light rotates on the printer status indicator.During the firmware download process, the printer status indicator turns to a steady half-orange and half-green as the printer writes to flash memory. Do NOT power cycle the printer during this phase.When the firmware download process is complete, the printer returns to normal operation. See Media Status Indicator on page 34 for more information on the indicator lights.Caution • During the firmware download process, the printer status indicator turns to a steady half-orange and half-green as the printer writes to flash memory. Do NOT power cycle the printer during this phase. Doing so makes the printer inoperable. If necessary, contact technical support for assistance (see Contacts on page 11).
4/23/08 HC100 User Guide 61207L-001 Rev. A6SpecificationsThis section contains the specifications for the printer and wristbands.ContentsPhysical and Environmental. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  76Printing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  76Wristband. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  77Standard and Optional Features  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  77Power Cord  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
SpecificationsPhysical and Environmental7661207L-001 Rev. A HC100 User Guide 4/23/08Physical and EnvironmentalPrintingPhysicalDimensions (LxWxH) 9.5x5x7 in. (242x127x178 mm)Clearance 6 in. (153 mm) above the printer to load a media cartridgeWeight 3.1 lb (1.4 kg)Electrical 100-240 VAC, 50-60 Hz external power supplyTemperatureOperating 40° to 104°F (5° to 40°C)Storage –40° to 140°F (–40° to 60°C)Relative HumidityOperating 20% to 85%, non-condensingStorage 5% to 85%, non-condensingPrinthead Resolution 300 dpiPrint Speed 2 in./sec (51 mm/sec)Dot size (width x length) 0.0033 in. x 0.0039 in. (0.084 mm x 0.099 mm)Minimum print length 3 in. (76 mm)Maximum print length 22 in. (558 mm)Bar code modulus(X) dimension 3.27 mil to 32.67 mil
77SpecificationsWristband4/23/08 HC100 User Guide 61207L-001 Rev. AWristbandStandard and Optional FeaturesWristband widths • 0.75 in (19 mm)• 1 in. (25 mm)• 1-3/16 in. (30 mm)Wristband closure types • Adhesive (Z-Band™ Direct)• Clip (Z-Band™ QuickClip)Wristband lengths Adhesive Closure Type• Adult (11 in./279 mm)• Pediatric (7 in./178 mm)• Infant (6 in./152 mm)Clip Closure Type• Adult (11 in./279 mm)• Infant (7 in./178 mm)Colors Adhesive Closure Type•Red•Blue• Yellow• Green•Pink•Purple•OrangeClip Closure Type•Red•Blue•Yellow•Green•Pink• PurpleMemory • Standard 8 MB Flash (2 MB user available)• Optional 64 MB Flash (58 MB user available)• Standard 16 MB SDRAM (4 MB user available)Connectivity • RS-232 Serial•USB 2.0• Optional 10/100 internal wired Ethernet (factory installed)• Optional 802.11 b/g internal wireless Ethernet (factory installed)Programming Languages •ZPL II•XML• Optional ZBI 2.0
SpecificationsPower Cord7861207L-001 Rev. A HC100 User Guide 4/23/08Power CordDepending on how your printer was ordered, a power cord may or may not be included. If one is not included or if the one included is not suitable for your requirements, see Figure 17 and refer to the following guidelines:• The overall cord length must be less than 9.8 ft. (3 m).• The cord must be rated for at least 10 A, 250 V.• The chassis ground (earth) must be connected to ensure safety and reduce electromagnetic interference.Figure 17 • Power Cord SpecificationsFigure 18 • International Safety Organization CertificationsCaution • For personnel and equipment safety, always use an approved three-conductor power cord specific to the region or country intended for installation. This cord must use an IEC 320 female connector and the appropriate region-specific, three-conductor grounded plug configuration.1AC power plug for your country—This should bear the certification mark of at least one of the known international safety organizations (Figure 18).23-conductor HAR cable or other cable approved for your country.3IEC 320 connector—This should bear the certification mark of at least one of the known international safety organizations (Figure 18).4Length ≤ 9.8 ft. (3 m). Rating 10 Amp, 250 VAC.3124
4/23/08 HC100 User Guide 61207L-001 Rev. AEnd User LicenseAgreementPlease read the terms of this “End User License Agreement” (the “Agreement”) carefully. The Agreement is a legal agreement between you (either an individual or a single entity) and Zebra Technologies International, LLC (“Zebra”) for the Zebra computer software and/or firmware accompanying this End User License Agreement, and any associated media, printed materials and any “online” or electronic documentation (collectively, “Software”). By installing or using the Software, you agree to be bound by the terms of this Agreement. If you do not agree to the terms of this Agreement, you may not install or use the Software. 1. Grant of License.  The Software is protected by copyright and other intellectual property laws and international treaties. The Software is licensed to you, and not sold, subject to the terms of this Agreement. Subject to the terms of this Agreement, Zebra hereby grants you a limited, personal, non-exclusive license during the term of this Agreement to use the Software solely and exclusively for your internal use for the operation of your associated Zebra printer(s) and for no other purpose. To the extent that any portion of the Software is provided to you in a manner that is designed to be installed by you, you may install one copy of the installable Software on one hard disk or other storage device for one printer, computer, workstation, terminal, or other digital electronic device, as applicable (an “Electronic Device”), and you may access and use that Software as installed on that Electronic Device so long as only one copy of such Software is in operation. If you are an organization rather than an individual, you may authorize personnel associated with your business to use the Software, but only one person at a time on one Electronic Device at a time. You agree not to duplicate or copy the Software, except that you may make one back-up copy for archive purposes. The primary user of the Electronic Device on which installable Software is installed may also make a copy for his or her exclusive use on a portable computer, so long as such Software is being used only on one Electronic Device at a time.2. Storage/Network Use.  In the alternative, you may install a copy of the Software on a storage device, such as a network server, used only to access and use the Software on your Electronic Devices over an internal network; however, you must acquire and dedicate a license for each separate Electronic Device on which the Software is accessed and used from the storage device. A license for the Software may not be shared or used concurrently on different Electronic Devices.
End User License Agreement8061207L-001 Rev. A HC100 User Guide 4/23/083. Documentation.  If the Software contains documentation which is provided only in electronic form, you may print one copy of such electronic documentation. You may not copy the printed materials accompanying the Software.4. Limitations of Reverse Engineering, Decompilation and Disassembly.  You may not reverse engineer, decompile, or disassemble the Software, except and only to the extent that such activity is permitted by applicable law notwithstanding this limitation.5. Transfer/Sublicense.  You may not transfer, sublicense, distribute, rent, lease, supply, market or lend the Software to any other party. 6. Confidentiality.   You acknowledge that the Software embodies confidential information owned by Zebra and/or its suppliers and licensors. To the extent you have access to any such information, you agree to use such information only for the authorized use of the Software. You further agree not to disclose such confidential information to any other party and to use at least the same degree of care to maintain the confidential nature of such information as you use to maintain the confidentiality of your own confidential information.7. Intellectual Property.  All title, copyrights and other intellectual property rights in and to the Software (including but not limited to copyrights, patents, trade secrets and trademarks) are owned by Zebra or its suppliers and licensors. You must maintain all copyright notices on all copies of the Software. All rights not expressly granted are reserved by Zebra. Without prejudice to any rights or remedies Zebra may have for your violation of this Software License, Zebra shall own all changes or modifications to the Software. 8. Termination.  Without prejudice to any other rights or remedies Zebra may have, Zebra may terminate this Agreement if you fail to comply with the terms and conditions of this Agreement. Zebra may terminate this Agreement by offering you a superseding Agreement for the Software or any replacement or modified version of or upgrade to the Software and conditioning your continued use of the Software or such replacement, modified or upgraded version on your acceptance of such superseding Agreement. In addition, either party may terminate this Agreement at any time. Subject to the foregoing, termination shall be effective upon notice to the other party. In the event that this Agreement terminates for any reason, your license to use the Software will terminate, and you must immediately stop using the Software, destroy all copies of the Software and all of its component parts, and, upon request, provide an affidavit certifying your compliance with the foregoing. The provisions of Sections 4, 5, 6, 7, 12, 13, 14, 15, 16, 17, 18, 19 and 20 shall survive termination of this Agreement.9. U.S. Government Restricted Rights.  You agree that the Software constitutes “commercial computer software” and/or “commercial computer software documentation” within the meaning of Federal Acquisition Regulation § 12.212 for civilian agencies and Defense Federal Acquisition Regulation Supplement § 227.7202. Accordingly, if you are an agency, department, employee, or other entity of the United States Government, the use, duplication, reproduction, release, modification, disclosure, or transfer of the Software, including technical data or manuals, is restricted by the terms, conditions and covenants contained in these EULA Terms and Conditions. All Software provided to the U.S. Government pursuant to solicitations issued prior to December 1, 1995 is provided with RESTRICTED RIGHTS as provided for in FAR, 48 CFR 52.227-19 (JUNE 1987) or DFARs, 48 CFR 252.227-7013 (OCT 1988), as applicable.
81End User License Agreement4/23/08 HC100 User Guide 61207L-001 Rev. A10. Export Restrictions.  You agree that you will not export or re-export the Software, any part thereof, or any process or service that is the direct product of the Software (the foregoing collectively referred to as the “Restricted Components”), to any country, person or entity subject to U.S. export restrictions. You specifically agree not to export or re-export any of the Restricted Components: (i) to any country to which the U.S. has embargoed or restricted the export of goods or services, which currently include but are not necessarily limited to Cuba, Iran, Iraq, North Korea, Sudan and Syria, or to any national of any such country, wherever located, who intends to transmit or transport the Restricted Components back to such country; (ii) to any person or entity who you know or have reason to know will utilize the Restricted Components in the design, development or production of nuclear, chemical or biological weapons; or (iii) to any person or entity who has been prohibited from participating in U.S. export transactions by any federal agency of the U.S. government. You warrant and represent that neither the U.S. Commerce Department, Bureau of Export Administration nor any other U.S. federal agency has suspended, revoked or denied your export privileges. Contractor/Manufacturer is Zebra Technologies Corporation, 333 Corporate Woods Parkway, Vernon Hills, Illinois 60061. 11. Accessing Services Using the Software.  Your use of any service accessible using the Software is not covered by this EULA and may be governed by separate terms of use, conditions or notices. Zebra and its suppliers and licensors hereby disclaim any such liability for any such services accessed.12. Your Security Responsibilities.  Notwithstanding anything to the contrary in this Agreement, as between Zebra and you, you acknowledge and agree that you are solely responsible for maintaining and protecting all aspects of any network, systems, and data (including any Personal Information) of, relating to, possessed by, or maintained by you, including maintaining and protecting such things from or against any theft, loss, misuse, alteration, disposal, or unauthorized access. “Personal Information” means individually identifiable information from or about an individual consumer including, but not limited to: (a) a first and last name or first initial and last name; (b) a home or other physical address, which includes at least a street name and name of city or town; (c) an email address; (d) a telephone number; (e) a Social Security number; (f) credit and/or debit card information, including number, expiration date, security code, and/or track data; (g) date of birth; (h) driver's license number; or (i) any other information from or about an individual consumer that is combined with (a) though (i) above.13. Disclaimer.  ZEBRA SUPPLIES THE SOFTWARE AS IS AND WITH ALL FAULTS AND DOES NOT MAKE ANY WARRANTIES WHATSOEVER, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO WARRANTIES CONCERNING THE SOFTWARE OR ANY APPLICATION, OPERATION OR USE THEREOF, THE OUTPUT OR THE DATA GENERATED BY THE OPERATION OR USE THEREOF, OR ANY SUPPORT SERVICES RENDERED WITH RESPECT THERETO. ZEBRA HEREBY EXCLUDES ALL IMPLIED WARRANTIES TO THE MAXIMUM EXTENT AUTHORIZED BY LAW, INCLUDING, SPECIFICALLY, ANY IMPLIED WARRANTY ARISING BY STATUTE OR OTHERWISE IN LAW OR FROM A COURSE OF DEALING OR USAGE OF TRADE, ALL IMPLIED WARRANTIES OF MERCHANTABILITY, OR OF MERCHANTABLE QUALITY, OR OF FITNESS FOR ANY PURPOSE, PARTICULAR, SPECIFIC OR OTHERWISE, OR OF TITLE, OR OF NONINFRINGEMENT. SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF IMPLIED WARRANTIES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. WHEN THE
End User License Agreement8261207L-001 Rev. A HC100 User Guide 4/23/08IMPLIED WARRANTIES ARE NOT ALLOWED TO BE EXCLUDED IN THEIR ENTIRETY, THEY WILL BE LIMITED TO THE DURATION OF NINETY (90) DAYS. WITHOUT LIMITING THE GENERALITY OF THE FOREGOING, ZEBRA DOES NOT WARRANT THAT THE OPERATION OF THE SOFTWARE WILL BE UNINTERRUPTED OR ERROR FREE. To the extent that the Software covered by this EULA includes emulation libraries, sUCH emulation libraries do not work 100% correctly or cover 100% of the functionality of the printer language being emulated, are offered “as is” AND WITH ALL FAULTS, AND ALL THE DISCLAIMERS AND LIMITATIONS CONTAINED IN THIS PARAGRAPH AND THIS AGREEMENT APPLY TO SUCH EMULATION LIBRARIES. 14. Limitation of Liability and Damages.  ZEBRA DOES NOT ASSUME RESPONSIBILITY FOR ANY SPECIFIC APPLICATION OF THE SOFTWARE OR FOR COMPATIBILITY WITH OTHER SOFTWARE OR EQUIPMENT. TO THE FULL EXTENT ALLOWED BY LAW, ZEBRA EXCLUDES FOR ITSELF AND ITS LICENSORS AND SUPPLIERS ANY LIABILITY FOR ANY DAMAGES, INCLUDING WITHOUT LIMITATION DIRECT, CONSEQUENTIAL, INCIDENTAL, INDIRECT, SPECIAL, EXEMPLARY OR PUNITIVE DAMAGES OF ANY KIND, OR FOR LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS, DAMAGE TO GOODWILL, LOSS OF INFORMATION OR DATA, OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE, USE, PERFORMANCE, FAILURE, OR INTERRUPTION OF ANY PRODUCTS, PARTS OR SOFTWARE, WHETHER BASED ON CONTRACT, TORT, NEGLIGENCE, STRICT LIABILITY OR OTHERWISE, EVEN IF ZEBRA OR ANY LICENSOR OR SUPPLIER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. TO THE MAXIMUM EXTENT AUTHORIZED BY LAW, THIS DISCLAIMER OF LIABILITY FOR DAMAGES WILL NOT BE AFFECTED IF ANY REMEDY PROVIDED HEREIN SHALL FAIL OF ITS ESSENTIAL PURPOSE. SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF DIRECT, INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. WHEN LIABILITY FOR DAMAGES IS NOT ALLOWED TO BE LIMITED OR EXCLUDED IN ITS ENTIRETY, ZEBRA LIMITS ITS LIABILITY TO REPAIR, REPLACEMENT, OR, AT ZEBRA'S OPTION, REFUND OF THE PRICE OF THE SOFTWARE. NOTWITHSTANDING ANYTHING TO THE CONTRARY IN THIS AGREEMENT, ZEBRA SHALL NOT, UNDER ANY CIRCUMSTANCE OR UNDER ANY LEGAL OR EQUITABLE THEORY (INCLUDING, WITHOUT LIMITATION, UNDER CONTRACT, TORT, CONTRIBUTION, OR INDEMNITY), BE LIABLE TO CUSTOMER OR TO ANY OTHER PARTY FOR ANY LOSSES, DAMAGES (WHETHER DIRECT, INDIRECT, SPECIAL, PUNITIVE, INCIDENTAL OR CONSEQUENTIAL), COSTS, EXPENSES, FINES OR FEES RELATING TO THE THEFT, LOSS, MISUSE, ALTERATION, OR DISPOSAL OF, OR UNAUTHORIZED ACCESS TO, ANY NETWORK, SYSTEM, OR DATA (INCLUDING PERSONAL INFORMATION) OF, RELATING TO, POSSESSED BY, OR MAINTAINED BY CUSTOMER. 15. Zebra Suppliers and Licensors.  Any release, disclaimer or limitation of Zebra's liability or damages pursuant to this Agreement shall be construed, in addition to Zebra's benefit, also to the benefit of Zebra's suppliers, licensors, employees, and contractors and, without limiting any other defenses that such suppliers, licensors, employees and contractors may have, you agree to release such parties from liability or damages in accordance with such release, disclaimer, or limitation of liability or damages to the same extent that such provisions apply to Zebra.
83End User License Agreement4/23/08 HC100 User Guide 61207L-001 Rev. A16. Governing Law.  To the maximum extent permitted by law, the laws of the State of Illinois, U.S.A., without reference to its conflict of laws provisions, will apply to this Agreement. You irrevocably agree to submit to the exclusive jurisdiction and venue of the state or federal courts in the State of Illinois in the event of any litigation involving this Agreement or the Software. You agree that you shall not assert any claim that you are not subject to the jurisdiction of such courts, that the venue is improper, that the forum is inconvenient or any similar objection, claim or argument. Zebra may, in its sole discretion, choose to resolve any controversy or dispute between you and Zebra concerning this Agreement, or the existence, validity, breach or termination thereof, whether during or after the term by binding arbitration in accordance with the Commercial Arbitration Rules of the American Arbitration Association (“AAA”), as modified or supplemented under this Section 15, by providing notice to you. In the event that Zebra provides such notice, you hereby waive any right to institute a court or other dispute resolution proceeding with respect to such controversy or dispute and acknowledge arbitration in accordance with this Section 15 as the sole and exclusive means of resolving such controversy or dispute. The arbitration proceeding will take place in Chicago, Illinois and be conducted in the English language. The arbitration panel will consist of 3 arbitrators, one arbitrator appointed by each party and a third neutral arbitrator appointed by the two arbitrators designated by the parties. Any communication between a party and any arbitrator will be directed to the AAA for transmittal to the arbitrator. The parties expressly agree that the arbitrators will be empowered to, at either party’s request, grant injunctive relief. The arbitral award will be the exclusive remedy of the parties for all claims, counterclaims, issues or accountings presented or pleaded to the arbitrators. Judgment upon the arbitral award may be entered in any court that has jurisdiction thereof. Any additional costs, fees or expenses incurred in enforcing the arbitral award will be charged against the party that resists its enforcement. Nothing in this Section will prevent Zebra from seeking interim injunctive relief against you or filing an action against you to collect unpaid and past due amounts in any court of competent jurisdiction.17. Injunctive Relief.  You acknowledge that, in the event you breach any provision of this Agreement, Zebra will not have an adequate remedy in money or damages. Zebra shall therefore be entitled to obtain an injunction against such breach from any court of competent jurisdiction immediately upon request without posting bond. Zebra's right to obtain injunctive relief shall not limit its right to seek further remedies.18. Entire Agreement.  This Agreement constitutes the entire understanding and agreement of the parties and supersedes any and all prior or contemporaneous representations, understandings and agreements between the parties with respect to the subject matter of this Agreement. If any provision of this Agreement is held invalid, the remainder of this Agreement shall continue in full force and effect.19. Assignment.  You may not assign this Agreement or any of your rights or obligations hereunder (by operation of law or otherwise) without the prior written consent of Zebra. Zebra may assign this Agreement and its rights and obligations without your consent. Subject to the foregoing, this Agreement shall be binding upon and inure to the benefit of the parties to it and their respective legal representatives, successors and permitted assigns.20. Modification.  No modification of this Agreement shall be binding unless it is in writing and is signed by an authorized representative of the party against whom enforcement of the modification is sought.21. Waiver.  The failure by a party to exercise any right hereunder shall not operate as a waiver of such party's right to exercise such right or any other right in the future.
End User License Agreement8461207L-001 Rev. A HC100 User Guide 4/23/0822. QUESTIONS.  Should you have any questions, or if you desire to contact Zebra for any reason, please contact the Zebra subsidiary serving your country, or write:Zebra Technologies International, LLC333 Corporate Woods ParkwayVernon Hills, Illinois 60061REVISED MARCH 2008.
4/23/08 HC100 User Guide 61207L-001 Rev. AIndexAadhesive wristbands, 22adjustmentsleft position, 63print darkness, 59tear-off position, 59wristband (label) top, 63Bbattery disposal, 53baud setting, 60bitmap scaling factor, 64CCanadian DOC compliance, 4cartridges. See media cartridgescleaning card, 44cleaning proceduresmedia path, 44smart card contacts and media cartridge sensor pins, 51clip wristbands, 23communications diagnostics testinterpreting results, 73selecting, 61connectivity options, 77contacts, 11control panelbuttons, 18location, 16location of lights, 18control prefix setting, 61counters, 64customer service, 11Ddarkness mode, 58darkness setting, 59data bits setting, 60data cable shielding, 28data communication interfacesconnecting data communication cables, 27port locations, 17default gateway, 67, 68default valueshow to restore print server defaults, 69how to restore printer parameters, 65delimiter character setting, 62diagnostics tools, 72disposal of printer parts, 53downloading firmwarelight sequence, 36overview, 74dpi format conversion, 64EEJECT button, 18end user license agreement, 79Ethernetcharacteristics of wireless connection, 28connector location, 17Ffail safe mode, 37FCC compliance, 4FCC radiation exposure limits, 4
Index8661207L-001 Rev. A HC100 User Guide 4/23/08feeding a wristband, 18firmware downloadlight sequence, 36overview, 74forced eject of media cartridgelight sequences, 36pressing and holding EJECT, 18format convert setting, 64format prefix setting, 62Hhome position on wristband, 24host handshake setting, 60Iindicator lights. See media status indicator, printer status indicator, or wireless status indicatorinspect for shipping damage, 26international safety organization marks, 78IP addressselecting method for obtaining, 67, 68view or modify, 66IP protocol, 67, 68Jjamming wristbands, 34Llabel (wristband) top setting, 63left position adjustment, 63liability, 2license agreement, 79lubrication, 53Mmaximum wristband length setting, 59media (wristband) specifications, 77media cartridge sensor pinscleaning, 51troubleshooting, 40media cartridge slot, 16media cartridgescleaning smart card contacts, 51damaging by pulling wristbands, 20described, 20inserting into printer, 31media levels, 34ordering, 11problems loading, 40media errors, 34media home position, 24media path cleaning, 44media sensor profiledescribed, 72PAUSE/FEED button description, 18media status indicatordescription of lights, 34location, 18memory options, 77Nnetwork ID setting, 61Oodometer, 64optional features, 77ordering media cartridges, 11ordering replacement parts, 53overheating, 40Pparity setting, 60PAUSE/FEED button, 18pausing the printerlight sequence, 36pressing PAUSE/FEED, 18platen roller cleaning, 44powerconnecting to power supply, 29power button and power connector locations, 17power cord specifications, 78print darkness setting, 59print quality problems, 40print servercharacteristics of wireless connection, 28print width setting, 59printer configuration wristbandPAUSE/FEED button description, 18printing, 56printer features, 77
87Index4/23/08 HC100 User Guide 61207L-001 Rev. Aprinter settingsbaud, 60communication diagnostics mode, 61control prefix, 61counters, 64darkness mode, 58data bits, 60delimiter character, 62format convert, 64format prefix, 62host handshake, 60left position, 63maximum wristband length, 59network ID, 61parity, 60print darkness, 59print width, 59protocol, 61serial communications, 59tear-off position, 59viewing, 56viewing on printer configuration wristband, 56viewing through web pages, 57wristband (label) top, 63wristband length, 59ZBI 2.0, 63ZPL mode, 62printer status indicator lightslocation, 18troubleshooting, 36printer storage, 26printhead cleaning procedures, 44printhead fail safe mode, 37printing specifications, 76programming languages, 77protocol setting, 61Rradiation exposure limits, 4recyclingprinter parts, 53replacement parts, 53report shipping damage, 26reprint mode for reprinting last wristband, 63resettable counters, 64Ssales, 11sensor profile, 72serial portcharacteristics of serial connection, 28connecting cable, 27connector location, 17setting serial communications, 59Set/Get/Do (SGD) commandscommands for changing print server settings, 66commands for changing printer settings, 58setupconnecting data communication cables, 27connecting to power supply, 29site selection, 27unpack the printer, 26shielded data cables, 28shippingreport damage, 26reshipping the printer, 26site selection, 27smart card contactscleaning, 51troubleshooting, 40standard features, 77status lights. See media status indicator lights or printer status indicator lightsstoring the printer, 26subnet mask, 67, 68Ttechnical support, 11temperature fail safe mode, 37top of wristband (label) setting, 63troubleshootingdiagnostics, 72media status indicator, 34printer status indicator lights, 36Uunpack the printer, 26upper cover, 16upper cover release button, 16USB portcharacteristics of USB connection, 28connector location, 17user-controlled counters, 64Vview printer settings, 56
Index8861207L-001 Rev. A HC100 User Guide 4/23/08Wwired print serverchanging parameters, 66connecting for the first time, 66connector location, 17wireless print serverchanging parameters, 66characteristics, 28connecting for the first time, 66wireless status indicator location, 18wristbandsadhesive type, 22clip type, 23level in media cartridge, 20level of media in media cartridge, 34loading, 31maximum length setting, 59printable area, 24printer cannot detect black mark, 35setting wristband length, 59sizes, 21specifications, 77troubleshooting, 40wristband (label) top setting, 63ZZBI 2.0 starting and stopping, 63Zebra Programming Language (ZPL)commands for changing print server settings, 66commands for changing printer settings, 58ZPL mode setting, 62
Part Number: 61207L-001 Rev. A© 2008 ZIH Corp.Zebra Technologies Corporation333 Corporate Woods ParkwayVernon Hills, Illinois 60061.3109 U.S.A.Telephone: +1 847 793 2600Facsimile: +1 847 913 8766Zebra Technologies Europe LimitedZebra HouseThe Valley Centre, Gordon RoadHigh WycombeBuckinghamshire, HP13 6EQ, UKTelephone: +44 (0) 1494 472872Facsimile: +44 (0) 1494 450103Zebra Technologies Asia Pacific, LLC120 Robinson Road#06-01 Parakou BuildingSingapore 068913Telephone: +65 6858 0722Facsimile: +65 6885 0838

Navigation menu