Zebra Technologies ZXP-LM 13.56MHz RFID Laminator User Manual Osprey Lam UM RevA

Download:
Mirror Download [FCC.gov]
Document ID	1146876
Application ID	SVIlSph9IIw734LyFw0apA==
Document Description	Users Manual Part 4 of 4
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	355.28kB (4440942 bits)
Date Submitted	2009-07-29 00:00:00
Date Available	2009-07-29 00:00:00
Creation Date	2009-07-01 08:11:03
Producing Software	Acrobat Distiller 9.0.0 (Windows)
Document Lastmod	2009-07-16 15:54:50
Document Title	_Osprey_Lam_UM_RevA.book
Document Creator	FrameMaker 8.0
Document Author:	tburton

ZXP Series Toolbox
Printer Configuration
Save/Restore
When you set up a printer, you can save the printer and driver configuration settings; then,
when you restore or add additional printers, you can use the saved configuration to ensure
configuration consistency.
Note that the Saved/Restored Settings (circled below) are for the Printer.
Note • The configuration files are stored in an XML format in the following default location:
C:\Documents and Settings\All Users\ZMotif\Config
•
The Save button saves the Driver Settings and/or Printer Settings in an XML file format.
The printer configuration settings are stored as P_
The driver configuration settings are stored as D_
The Restore button restores the Driver Settings and/or Printer Settings.
P1013772-001 Rev. A ( Draft 1 )
Zebra ZXP Series 8 Card Printer User’s Manual
71
ZXP Series Toolbox
Printer Configuration
Job Log
The Job Log is a utility that builds a database of card transactions in the printer’s host
computer. Job Log records data encoded on the card’s magnetic stripe, together with date,
time, and the printer’s serial number.
The data set can be uploaded at any time to a central archive, thus providing a means for
security officers to validate the card by comparing it with tamper-proof real data.
72
•
Enable Logging - If this box is checked, the logging feature is enabled.
•
Logfile Definition - Choose one of the following options:
If the “Create new log file each day” box is unchecked, the data is saved to a log file
of your choice (Filename).
If the box is checked, the data is saved to log file ZXPLog with the day’s date; e.g.,
ZXPLog_2009_3_4.
In addition to the Filename, you may wish to enter a special field Separator Character.
The default field Separator Character is “|”.
Zebra ZXP Series 8 Card Printer User’s Manual
P1013772-001 Rev. A ( Draft 1 )
ZXP Series Toolbox
Printer Configuration
•
Log File Contents - The Log File Contents group selects the data to be logged in the file
you specified above.
The data will be logged in the order displayed on the screen, each field being separated by
the character specified in the Logfile Definition, Separator.
Log File Contents selections include:
Time: Logs the time a which the card was sent to the printer in the HH:MM:SS
format. The 24-hour clock is used, so 13:00:00 = 1:00 pm, and 05:00:00 = 5:00 am.
Date: Logs the date the card was sent to the printer in the MM/DD/YYYY format.
Printer serial number: Logs the serial number of the printer that printed the card.
Static text: Adds to the record text in the box at right, 16 characters maximum.
IP address: Logs the IP address of the PC that sent the card to the printer.
Magnetic Track 1, 2, 3 Data: Logs the data sent to the printer to be encoded on the
card’s magnetic stripe.
EIN data from Mag Track 2: Not implemented.
Application will send data with “ L=xxx” TextOut: Allows third-party applications
to send data to be logged in much the same way as they would send magnetic data.
Spooler job number: Logs the number which the card print job was assigned in the
Windows print spooler.
User name: Logs the username of the person submitting the card print job.
Note • Job Logs and Printer Logs are stored in the following default location:
C:\Documents and Settings\All Users\ZMotif
The Save button saves the Job Log settings.
The Save Printer Log button creates the following XML Log Files:
GetLogCleanHistory.xml
GetLogErrors.xml
GetLogEventHistory.xml
GetLogServiceHistory.xml
P1013772-001 Rev. A ( Draft 1 )
Zebra ZXP Series 8 Card Printer User’s Manual
73
ZXP Series Toolbox
Printer Configuration
Image Control
The Image Control window lets you make color adjustments to compensate for camera or
lighting conditions.
Keep in mind that these color adjustments modify how the pictures print. The adjustments do
not affect the image files. (That type of adjustment would be made in an image processing
application program.)
•
The Monochrome conversions dropdown menu lets you select Dither error diffusion,
dither halftoning, or Dither pure black on white.
•
Full color printing adjustments (-25 to +25 range) include Brightness, Contrast,
Gamma, Saturation, Red, Green, and Blue.
•
Sharpening filter options are None, Normal, and High. Note that these adjustments have
no effect on the preview image.
Depending on the radio button selected, you can use the color matching profile selected in
Properties > Color Management or you can disable the color matching profile.
The Save button saves your image control settings.
The Restore Defaults button restores the image control default values.
74
Zebra ZXP Series 8 Card Printer User’s Manual
P1013772-001 Rev. A ( Draft 1 )
ZXP Series Toolbox
Printer Configuration
Firmware Download
The Firmware Download screen allows you to download firmware and firmware updates. Note
that firmware updates can be found at http://zebracard.com under Drivers & Downloads.
Caution • Do not turn power OFF while the printer is downloading and configuring the
new firmware.
P1013772-001 Rev. A ( Draft 1 )
Zebra ZXP Series 8 Card Printer User’s Manual
75
ZXP Series Toolbox
Print Test Card
Print Test Card
Print Sample Card
Note • The sample cards in the Test Card Library are .bmp images stored in the following
default location:
C:\Documents and Settings\All Users\ZMotif\Library
1.
View the Test Card Library. Use the scrollbar to view all the selections.
2.
Set the front side:
a.
Select (click on) a card from the Test Card Library.
b.
Click on the Set As Front button.
c.
View the selected card in the Preview. Note that to remove the selected card from
the Preview, click on the Set As Front button.
d.
To change your selection, repeat steps a through c.
3.
Set the back side: same as step 2, except click on the Set As Back button.
4.
When satisfied with your selection, click on the Print button to print the sample card.
The Reprint last card button sends a command to the printer to print the last card.
76
Zebra ZXP Series 8 Card Printer User’s Manual
P1013772-001 Rev. A ( Draft 1 )
ZXP Series Toolbox
Technology
Technology
Note • Magnetic Encoding and Smart Card default values are set via the Card type in use
option in the Card Setup tab, see page 60)
Magnetic Encoding
The Magnetic Encoding screen allows the user to test various magnetic encoding options. For
more information on magnetic encoding, refer to Appendix C.
Settings: EIN options not implemented.
Read Data:
•
Coercivity: Select either High or Low.
•
Track selection:
For encoding: Click on the checkboxes to select Track 1, Track 2, and/or Track 3;
enter the data to be written; and click on the Encode button.
For reading: Click on the checkboxes to select Track 1, Track 2, and/or Track 3; click
on the Read button, and validate the data read.
P1013772-001 Rev. A ( Draft 1 )
Zebra ZXP Series 8 Card Printer User’s Manual
77
ZXP Series Toolbox
Technology
Smart Card
The Smart Card screen allows the user to test various smart card encoding options. For more
information on smart card encoding, refer to Appendix D.
•
Card Readers: Select the card reader from the drop-down menu.
•
•
Card Option: Select either Contact or Contactless.
Card Types: Select the card type from the drop-down menu.
The Feed Card button feeds the card into the printer.
Input Data includes address, length, and input.
•
Click on the Read button to read data from the card.
•
Click on the Write button to write data to the card.
•
Click on the Write Raw Data button to write “raw data” to a card.
The Get ATR button returns the ATR (Answer To Reset) result from the card reader. This
is useful to identifying the type of smart card inserted into the printer.
The Eject Card button ejects the card.
Click on the Messages checkbox to show the output in hex format.
78
Zebra ZXP Series 8 Card Printer User’s Manual
P1013772-001 Rev. A ( Draft 1 )
ZXP Series Toolbox
Advanced Security
Advanced Security
Important • To manage this Advanced Security section, you are required to be the
administrator of the computer or have administrative privileges.
Configure Security
Enabling driver password protection prevents unauthorized persons from changing the printer
configuration settings. Access to various printer screens can be selectively disabled based on
the Windows User Login.
To activate Driver Password Protection:
1.
Click on the Activate driver password protection checkbox.
2.
Enter the new password on the New password field. The password is case sensitive,
eight characters minimum.
3.
Repeat the password in the Confirm password field.
4.
Click on the Apply button.
P1013772-001 Rev. A ( Draft 1 )
Zebra ZXP Series 8 Card Printer User’s Manual
79
ZXP Series Toolbox
Advanced Security
To deactivate Driver Password Protection:
1.
Click on the Activate driver password protection checkbox to remove the checkmark.
2.
Enter your password in the Old password field.
3.
Leave the New password and the Confirm password fields blank.
4.
Click on the Apply button. This will bring up a ZXP Series Toolbox pop-up screen.
To deactivate the the printer driver password, click on Yes. This will bring up another
ZXP Series Toolbox pop-up screen. Click on OK.
Last Print job option:
•
The Erase job data following successful card printing option erases the print job after
successful card printing.
•
The Retain job data after card printing option allows the print job to remain in memory
for multiple prints via the OCP.
The Save button saves your selection.
80
Zebra ZXP Series 8 Card Printer User’s Manual
P1013772-001 Rev. A ( Draft 1 )
ZXP Series Toolbox
Advanced Security
Security Roles
Use this section used to establish security roles; i.e., grant and restrict access to various ZXP
Series Toolbox screens.
Note • The list of users in the drop-down menu (e.g., Guest, HelpAssistant, Local User,
localfix, etc.) is derived from the list of users on the system.
To set security access roles:
1.
Select a user from the drop-down menu.
2.
Use the arrow buttons (>, >>, <, and <<) to make specific features available to or
restrict specific features from the selected user role.
3.
When satisfied with the selection, click on the Save button.
At the next log in, the user will only see or have access to the features previously granted.
P1013772-001 Rev. A ( Draft 1 )
Zebra ZXP Series 8 Card Printer User’s Manual
81
ZXP Series Toolbox
Print Viewer
Print Viewer
When you print a PRN file, you print directly to the printer, bypassing computer applications
and associated printer drivers. This utility can be used to ensure that your printer is working
properly by isolating it from driver-related and communication-related issues.
Print PRN file
Note • Sample PRN files are stored in the following default directory/folder:
C:\Documents and Settings\All Users\ZMotif\Library
To send a PRN file to the printer:
1.
Click on the Browse button.
2.
From the Browse window, locate and select a PRN file.
3.
Click on the Open button.
4.
View the PRN file.
5.
When satisfied with the selection, click on the Print button.
Successfully printing the PRN file indicates that the printer and data communications to the
printer are set up and configured properly.
82
Zebra ZXP Series 8 Card Printer User’s Manual
P1013772-001 Rev. A ( Draft 1 )
6
Cleaning
Caution • PROTECT YOUR FACTORY WARRANTY!
The recommended cleaning procedures must be performed to maintain your
factory warranty. Other than the recommended cleaning procedures described in
this manual, allow only Zebra authorized technicians to service the Printer.
NEVER loosen, tighten, adjust, bend, etc., any part or cable inside the printer.
NEVER use a high pressure air compressor to remove particles in the printer.
Cleaning the Printer
Clean your Printer using the Cleaning Cards provided. The regular use of these cards will
clean and maintain important parts of your printer that cannot be reached, including the
Printhead, Transport Rollers, and optional Magnetic Encoder Station.
When to Clean
• X-Roller and Y-Roller cleaning should occur every 5,000 cards.
• Heated Roller cleaning should occur every 20,000 cards. Note that a Heated Roller
Cleaning Card is not supplied with the printer; order Zebra Cleaning Card Kit
P/N 105999-001.
P1013772-001 Rev. A ( Draft 1 )
Zebra ZXP Series 8 Card Printer User’s Manual
83
Cleaning
Cleaning the Printer
Cleaning the Rollers
Note • Do not use previously used cleaning cards.
Step 1. Initiate the cleaning process.
a.
Press the MENU button on the Operator Control Panel (OCP). The OCP will
display the Main Menu.
b.
Scroll through the Main Menu, and select Advanced Settings. The OCP will
display the Advanced Settings Menu.
c.
Scroll through the Advanced Settings Menu, and select Clean Printer. The OCP
will display the Clean Printer Menu.
Step 2. Clean the X-Drive Rollers.
84
a.
Select Clean Side Card Path to run the X-Roller Cleaning Routine.
b.
Use X-Path Cleaning Card 211973-001.
c.
Follow the OCP instructions.
d.
When complete, the OCP will return to the Clean Printer Menu.
Zebra ZXP Series 8 Card Printer User’s Manual
P1013772-001 Rev. A ( Draft 1 )
Cleaning
Cleaning the Printer
Step 3. Clean the Y-Drive Rollers.
a.
Select Clean Front Card Path to run the Y-Roller Cleaning Routine.
b.
Use Y-Path Cleaning Card 211974-001.
c.
Follow the OCP instructions.
d.
When complete, the OCP will return to the Clean Printer Menu.
Step 4. Clean the Heated Rollers.
a.
Select Clean Heated Roller Path to run the Heated Roller Cleaning Routine.
b.
Use Heated Roller Cleaning Card P/N 211975-001.
c.
Peel the protective film from the card..
d.
Follow the OCP instructions.
e.
When complete, the OCP will return to the Clean Printer Menu.
f.
Then use the Heated Roller Cleaning Card to clean the Platen; see page 86.
Exit the Printer Menus by selecting RETURN at each menu level (Clean Printer Menu,
Advanced Settings Menu, and Main Menu).
P1013772-001 Rev. A ( Draft 1 )
Zebra ZXP Series 8 Card Printer User’s Manual
85
Cleaning
Cleaning the Printer
Cleaning the Platen
Step 1. Open the printer Door.
Step 2. Remove the Transfer Film.
Step 3. Manually run the Heated Roller Cleaning Card (P/N 211975-001) over the Platen.
Platen
Step 4. Re-install the Transfer Film.
Step 5. Close the printer Door.
86
Zebra ZXP Series 8 Card Printer User’s Manual
P1013772-001 Rev. A ( Draft 1 )
Cleaning
Cleaning the Printhead
Cleaning the Printhead
A cleaning using the Cleaning Cards usually suffices; however, a separate Printhead cleaning
can remove more stubborn deposits when print anomalies persist. To avoid deposits, only use
foam-tipped swabs.
Caution • Never use a sharp object or any abrasive to scrape deposits from the
Printhead. Permanent damage to the Printhead will result.
Caution • Do not touch the Printhead if the printer has been in service in the last
10 minutes. It could be very hot and cause a burn.
Step 1. Place the printer power switch in the OFF (
) position.
Step 2. Open the Door, and remove the print ribbon.
Step 3. Bend the Cleaning Swab to release the cleaning fluid.
Step 4. Clean Printhead by moving Cleaning Swab tip side-to-side across the Printhead
elements. Only use moderate force. To re-order Cleaning Swabs, see the Media List
on the User Documentation and Drivers CD supplied with this printer.
Step 5. Reinstall the print ribbon, and close the Door.
Step 6. Place the printer power switch in the ON position.
P1013772-001 Rev. A ( Draft 1 )
Zebra ZXP Series 8 Card Printer User’s Manual
87
Cleaning
Card Cleaning Cartridge
Card Cleaning Cartridge
The Card Cleaning Cartridge cleans the cards entering the printer through the card feeder. To
ensure print quality, the card cleaning roller requires periodic replacement. New card cleaning
rollers are included with each print ribbon or may be purchased separately. (To reorder, refer to
the Media List on the User Documentation and Drivers CD supplied with this printer.)
Installation of the Card Cleaning Cartridge is described in Section 2 and is not repeated in
detail here.
Note • Before replacing the Card Cleaning Cartridge or its adhesive roller, clean the Printer
using the Cleaning Cards as described earlier in this chapter.
Cleaning Roller
The Card Cleaning Roller cleans the cards entering and exiting the Transfer Station. To ensure
print quality, the card cleaning roller requires periodic replacement. A new card cleaning roller
is included with each print ribbon or may be purchased separately. (To reorder, refer to the
Media List on the User Documentation and Drivers CD supplied with this printer.)
Installation of the Card Cleaning Roller is described in Section 2 and is not repeated in
detail here
88
Zebra ZXP Series 8 Card Printer User’s Manual
P1013772-001 Rev. A ( Draft 1 )
7
Troubleshooting
The table on the next page offers causes and solutions to symptoms related to improper
operation. Check the table when experiencing any loss of operation or print quality.
Use the following figure in conjunction with the table to help locate the possible cause and
effect a solution.
Door (shown open)
Transfer
Film
Transfer
Station
Eject
Roller
Print
Ribbon
Input
Hopper
Idler Roller
Assembly Door
Operator Control
Panel (OCP)
Single Card
Feed Slot
P1013772-001 Rev. A ( Draft 1 )
Zebra ZXP Series 8 Card Printer User’s Manual
89
Troubleshooting
OCP Error Messages
OCP Error Messages
ERROR MESSAGE
POSSIBLE CAUSE
POSSIBLE SOLUTION
BOTTOM CUTTER FAIL
17020
BOTTOM CUTTER STALL
17018
BOTTOM HEATER FAIL
17014
BOTTOM LAMINATE FEED
17006
BOTTOM OVER TEMP
17016
BOTTOM SENSOR FAIL
17022
CARD CLEAN ERROR
Faulty Card Cleaning Roller (if error
during single card feed) or Card Cleaning
Cartridge (if cards fed from Input Hopper)
Replace the Card Cleaning Roller or
Card Cleaning Cartridge, as appropriate
CARD FEED ERROR
Card is jammed in Input Hopper
a. Clear the card jam in the Input
Hopper, and re-seat the Input Hopper
b. Ensure that cards are not stuck
together and that they are the correct
thickness (30 - 40 mil)
CARD JAM
Card is jammed in Card Transport or
Transfer Station
Check the card path:
a. Idler Roller Assembly (open door)
b. Transfer Station (rotate the eject
roller CCW)
CARD NOT DETECTED
Card did not reach card sensor or is
jammed in Input Hopper or
Card Transport
a. Clear the card jam in the Input
Hopper, and re-seat the Input Hopper
b. Ensure that cards are not stuck
together and that they are the correct
thickness
c. Check Idler Roller Assembly
(open door)
CARD NOT INSERTED
Card was not fed into Single Card
Feed Slot within nominal 30-second
period
Retry and feed card into the Single Card
Feed Slot, or cancel the operation
COVER OPEN
Door is ajar
Verify the Door is completely closed
EARLY CARD JAM
17009
EEPROM PARAMS
CORRUPT
17024
EMI TEST
17039
EP SCRIPT ERROR
Internal logic error
a. Power cycle the printer
b. Contact Zebra Technical Support
ETHERNET COMM
ERROR
18001
FAN FAIL
17023
FILM JAM
The Transfer Film is jammed
a. Check the Transfer Film
b. Reinstall the Transfer Film
c. Repair the break in the Transfer Film
and reinstall
90
Zebra ZXP Series 8 Card Printer User’s Manual
P1013772-001 Rev. A ( Draft 1 )
Troubleshooting
OCP Error Messages
ERROR MESSAGE
POSSIBLE CAUSE
POSSIBLE SOLUTION
FILM MOTION ERROR
Transfer Film not correctly responding to
motion commands
a. Check the Transfer Film
b. Reinstall the Transfer Film
c. Power cycle the printer
d. Contact Zebra Technical Support
FW UPGRADE ERROR
Invalid firmware version selected
Verify the version, and retry updating the
firmware
GENERAL MEMORY
ERROR
There is a problem when accessing
memory
a. Power cycle the printer
HCB BULB ERROR
The Heater Controller Board (HCB) is
unable to pulse the upper and lower
heaters to bring the upper and lower
rollers to the proper temperature
Contact Zebra Technical Support
HCB SENSOR ERROR
The Heater Controller Board (HCB) is
unable to detect temperature of the
upper or lower rollers
Contact Zebra Technical Support
INVALID BOT LAMINATE
17030
INVALID CARD TYPE
Encoding error
b. Contact Zebra Technical Support
a. Ensure that you are using the correct
card type
b. In the Encoding tab of the driver
Printing Preferences, check that the
settings are correct for the cards you
are using
c. Ensure that the data conforms to
ISO Specifications
d. Retry writing and reading
INVALID FILM
Transfer Film does not match the printer
INVALID RIBBON
Print ribbon does not match the printer
a. Verify the part number of the Transfer
Film is correct on OCP
b. Power cycle the printer
a. Verify the part number of the print
ribbon is correct on OCP
b. Power cycle the printer
INVALID TOP LAMINATE
17029
LAMINATE
REGSITRATION
17007
LAMINATOR COVER
OPEN
17038
LAMINATOR FAILED INIT
17002
LAMINATOSTANDBY
17037
LAMINATOR WARMING
17036
LATE CARD JAM
17011
MAG MOTION ERROR
Mag card positioning error encountered
P1013772-001 Rev. A ( Draft 1 )
Retry writing and reading
Zebra ZXP Series 8 Card Printer User’s Manual
91
Troubleshooting
OCP Error Messages
ERROR MESSAGE
POSSIBLE CAUSE
POSSIBLE SOLUTION
MAG READ ERROR
• Encoding error
a. Ensure that you are using the correct
card type
• Defective magnetic stripe
b. Check that the cards are loaded with
the magnetic stripe in the correct
orientation (normally this will be with
the stripe down and toward the rear
of the printer)
c. Ensure that the cards are set-up
correctly in the printer driver
(coercivity setting)
d. Ensure that the data conforms to
ISO Specifications
e. Retry reading
MAG WRITE ERROR
• Encoding error
• Defective magnetic stripe
a. Ensure that you are using the correct
card type
b. Check that the cards are loaded with
the magnetic stripe in the correct
orientation (normally this will be with
the stripe down and toward the rear
of the printer)
c. Ensure that the cards are set-up
correctly in the printer driver
(coercivity setting)
d. Ensure that the data conforms to
ISO Specifications
e. Retry writing
MID CARD JAM
17010
a.
MISSING HCB ERROR
There is a problem with the Heater
Controller Board (HCB)
a. Power cycle the printer
MISSING LAMINATOR
17001
a.
MISSING MAB
An error occurred when reading the
RFID Tag by the MAB (Media
Authentication Board)
a. Check print ribbon orientation
b. Contact Zebra Technical Support
b. Verify part number of the print ribbon
c. Power cycle the printer
d. Contact Zebra Technical Support
MOTOR VOLTAGE ERROR
Incorrect voltage detected at one or
several motors in the unit
a. Power cycle the printer
NO MAG STRIPE
Mag stripe not detected
a. Ensure that you are using the correct
card type
b. Contact Zebra Technical Support
b. Check that the cards are loaded with
the magnetic stripe in the correct
orientation (normally stripe down and
toward the rear of the printer)
OUT OF CARDS
OUT OF FILM
92
• The Input Hopper is empty
a. Load cards in the Input Hopper
• Card is stuck in Input Hopper
b. Re-seat the Input Hopper
The Transfer Film has run out
Load new roll of Transfer Film
Zebra ZXP Series 8 Card Printer User’s Manual
P1013772-001 Rev. A ( Draft 1 )
Troubleshooting
OCP Error Messages
ERROR MESSAGE
POSSIBLE CAUSE
POSSIBLE SOLUTION
OUT OF RIBBON
The print ribbon has run out
Load a new roll of print ribbon
POLL TIMEOUT
17012
PRINTHEAD MOTION ERR
Printhead did not move to proper position
during initialization
a. Power cycle the printer
PRINTHEAD TOO COLD
Printhead temperature out of proper
range (COLD)
Contact Zebra Technical Support
PRINTHEAD TOO HOT
Printhead temperature out of proper
range (HOT)
Contact Zebra Technical Support
REJECT ERROR
A problem during the reject process
Contact Zebra Technical Support
RIB COLOR DETECT ERR
Print ribbon is not installed correctly
Reinstall the print ribbon
RIBBON ADC ERROR
Possible hardware issue
Contact Zebra Technical Support
RIBBON BEMF ERROR
Problem with the Back EMF (BEMF) of
the ribbon motors
Contact Zebra Technical Support
RIBBON JAM
The print ribbon is jammed
a. Check the print ribbon
b. Contact Zebra Technical Support
b. Reinstall the print ribbon
c. Repair the break in the print ribbon
and reinstall
RIBBON MOTION ERROR
Ribbon not correctly responding to
motion commands
a. Check the print ribbon
b. Reinstall the print ribbon
c. Repair the break in the print ribbon
and reinstall
ROLLERS OVER TEMP
Heated Rollers (used to transfer the
image from the Transfer Film to the
Card) are too hot for proper operation
Turn off power, and contact Zebra
Technical Support
ROLLERS UNDER TEMP
Heated Rollers (used to transfer the
image from Transfer Film to Card) are
not hot enough for proper operation
Turn off power, and contact Zebra
Technical Support
STAGING
17008
a.
SYSTEM ERROR
Internal logic error
a. Power cycle the printer
b. Contact Zebra Technical Support
SYSTEM NOT READY
A problem was detected during printer
start-up
TOP CUTTER FAIL
17019
TOP CUTTER STALL
17017
TOP HEATER FAIL
17013
TOP LAMINATE FEED
17005
TOP OVER TEMP
17015
TOP SENSOR FAIL
17021
TRANSFER ERROR
A problem was detected during the
transfer process (print ribbon to film)
WIFI COMM ERROR
19001
P1013772-001 Rev. A ( Draft 1 )
a. Power cycle the printer
b. Contact Zebra Technical Support
Contact Zebra Technical Support
Zebra ZXP Series 8 Card Printer User’s Manual
93
Troubleshooting
OCP Test Card Images
OCP Test Card Images
See detailed Test Card descriptions on the following page.
Mid Gray
Grid On Gray
Cyan Stripes
2 Pixel Grid
Mid Magenta
Dark Cyan
Max Gray
Offset Dots
Smear
Min Magenta
White Max-Gray
Max-Gray White
Motion & Registration
Gradient Boxes
Density Setup
Grid On Gray 2
94
Zebra ZXP Series 8 Card Printer User’s Manual
P1013772-001 Rev. A ( Draft 1 )
Troubleshooting
Test Card Descriptions
Test Card Descriptions
Image
Description
Print artifacts to look for with this image
Mid Gray
Flat uniform gray
Motion artifacts, banding, platen defects, transfer
artifacts, dirt, overall density level
Grid On Gray
Solid black on top,
Colored ribbon wrinkles in the black area, or clear/white
gray grid underneath transfer film wrinkles in the gray area
Cyan Stripes
Horizontal cyan
stripes alongside
vertical lighter
cyan box
Non-uniformity or horizontal banding within cyan box on
right of card
2 Pixel Grid
2 pixel wide grid
lines on white
Mis-registration between color planes
Mid Magenta
Flat uniform middensity magenta
Motion artifacts, banding, platen defects, density level,
uniformity
Dark Cyan
Maximum cyan only
density image
Motion artifacts, transfer artifacts, scratches, dirt
Max Gray
Maximum CMY
(black) density
image
Wrinkles, snapping noise during printing, ribbon /
transfer-film tears or breaks, flash, card positioning
Offset Dots
Individual C, M, and
Y dots spaced at
regular intervals
Motion artifacts on specific color planes, mis-registration
Smear
Gray with full density Color smear artifacts
YMCK blocks
near top
Min Magenta
Flat uniform lowdensity magenta
White Max-Gray Max-density areas
on sides with tilted
white center
Motion artifacts, banding, platen defects, density level,
uniformity, bead position
Ribbon wrinkle
Max-Gray White Same as above with Ribbon wrinkle
slant direction
changed
Motion &
Registration
Uniform cyan with
registration marks
on sides
Gradient Boxes
3 sets of light-to-dark Used to create color calibration look-up table
grayscale ramps
Density Setup
Used to measure
mid and max
densities
Density level of mid-gray and black
Grid On Gray 2
Less stressful
version of the gridon-gray target
Colored ribbon wrinkles in the black area, or clear/white
transfer film wrinkles in the gray area
P1013772-001 Rev. A ( Draft 1 )
Banding, mis-registrations, motion artifacts
Zebra ZXP Series 8 Card Printer User’s Manual
95
Troubleshooting
Ethernet Issues
Ethernet Issues
If both LEDs are off, the printer has not detected the presence of a network cable. To solve
the problem:
• Verify that the network cable is appropriate and has an RJ-45 connector.
• Remove the network cable from the printer. Plug the network cable back in until you hear
a positive click. Check the other end of the cable in the same manner. If the printer still
does not detect a cable, then continue.
• Connect the printer to a known good network. If the printer is still unable to detect the
network cable, contact Technical Support for assistance.
96
Zebra ZXP Series 8 Card Printer User’s Manual
P1013772-001 Rev. A ( Draft 1 )
8
Technical Specifications
Standard Features
•
Thermal transfer and dye diffusion to transfer film
•
Full color or monochrome reverse transfer printing
•
Single- and dual-sided printing
•
Maximum print speed (batch mode; i.e., the same image repeatedly)
•
Single-sided (Front Only)
190 cph
160 cph
YMC
YMCK
•
Dual-sided (Front and Back)
YMCK (YMC Front, K Back)
YMCKK (YMCK Front, K Back)
170 cph
150 cph
•
Photo quality image
•
Over-the-edge printing on standard CR80 media
•
Microsoft Windows Certified drivers
•
Single-card feed capability
•
150 card capacity feeder (30 mil)
•
15 card reject hopper (30 mil)
•
100 card output hopper (30 mil)
•
i Series™ intelligent media technology
•
Auto calibration of media
•
21-character soft menu LCD text operator display
•
304 dpi (12.0 dots/mm) print resolution
•
64MB memory standard
•
2-year unlimited warranty on printer, lifetime limited warranty on printhead with Genuine
Zebra Supplies
P1013772-001 Rev. A ( Draft 1 )
Zebra ZXP Series 8 Card Printer User’s Manual
97
Technical Specifications
Specifications
Specifications
Encoding Options
•
Smart card contact encoder – ISO 7816, PC/SC Compliant
•
Magnetic stripe encoder – ISO 7811 and JIS-II (new and re-encoded; tracks 1, 2, and 3;
high and low coercivity; stripe down; 30 - 40 mil card thickness)
•
Contact smart card encoder – EMV level 1 certified
•
ISO 14443 MIFARE (13.56 MHz) and ISO 7816 contact encoder combo
Communications Interfaces
•
USB V2.0 / 1.1 protocol
•
USB supports plug-n-play printer identification
•
USB and internal 10/100 Ethernet (Standard)
Software
Microsoft Windows Certified Printer Drivers Supported
•
Windows XP*, Windows Vista*, Windows Server 2003*
*32-bit and 64-bit certified
Driver Features
•
Graphical card orientation setting to visualize card printing setup and configuration
•
Card type setting eliminates unnecessary setup and configuration settings
•
Complete graphical control over area and element selection of black extraction parameters
insures true black and color printing exactly where you want it on the card
•
Auto sensing of print ribbon type
•
Optional driver password protection setting to prevent accidental or unauthorized driver
configuration changes
ZXP Toolbox
98
•
Printer configuration tools and utilities for complete control over all printer functions
and features
•
User role-based features enables true security printer operations
•
Complete technology card management enables setup and testing of all printer and
encoder features and functionality
•
Printer test cards and diagnostics utilities ensure error free printing and fast
troubleshooting capabilities
Zebra ZXP Series 8 Card Printer User’s Manual
P1013772-001 Rev. A ( Draft 1 )
Technical Specifications
Specifications
Card Compatibility
•
Card Thickness: 30 – 40 mil
•
Card Size: ISO 7810 format, Type ID-1, CR-80
•
Card Material: ABS; PVC, Composite; TESLIN, Composite; PET; PETG;
Polycarbonate; PVC
Agency Approvals
Zebra ZXP Series 8 Card Printer complies with following applicable directives and standards
for the ITE: Residential, Commercial & Light Industry environments
•
•
For US/Canada/Mexico/Australia&NZ
•
FCC Class A, cfr47, Part 15 Subpart J
•
FCC 15.257 2008, Part15 Subpart C
•
Canadian STD RSS-210
•
NOM-ETL (Mexico)
•
EN60950: 2000 Safety Standard (TUV & RTL)
•
C-Tick (Australia) Electromagnetic Radiation Standard
For Europe:
•
Applicable Directives and Supporting Standards:
2004/108/EC EMC Directive, EN55022:2006 Class A,
EN55024:1998+AD1:2001+AD2:2003,
EN61000-3-2:2006, EN61000-3-3:1995+AD1:2001,
2006/95/EC LVD Directive, EN60950-1:2001, CB Scheme
•
WLAN Enabled
Applicable Directives and Supporting Standards:
99/5/EC R&TTE Directive, EN 301 489-17 V1.2.1 (2002-08),
EN 300 328 V1.7.1 (2006-10)
•
RFID Enabled
Applicable Directives and Supporting Standards:
99/5/EC R&TTE Directive, EN 301 489-3 V1.4.1 (2002-08),
EN 300 220-2 V2.1.2 (2007-06)
P1013772-001 Rev. A ( Draft 1 )
Zebra ZXP Series 8 Card Printer User’s Manual
99
Technical Specifications
Specifications
Electrical
•
Auto-switching Single-phase AC power
•
90V~264V AC RMS and 47-63 HZ (50-60 Hz nominal)
•
Power consumption:
Idle
Printing
Initializing / Warm-up
Sleep
100 W
150 W
300 W
20 W
Physical
Printer
•
Height (printer only)
11.9" (303 mm)
•
Height (with card feeder)
13.2" (336 mm)
•
Width
14" (356 mm)
•
Width (with card feeder)
14.9" (379 mm)
•
Depth
20.4" (519 mm)
•
Weight (printer only)
27.5 lbs (12.5 kg)
Laminator
• Height
11.6" (295 mm)
• Width
11.76" (299 mm)
•
Depth
13.15" (334 mm)
•
Weight
TBD
Environmental
100
•
Operating Temperature
59º to 95ºF (15º to 35ºC)
•
Storage Temperature
23º to 131º F (-5º to 55ºC)
•
Operating Humidity
20% to 80% non-condensing
•
Storage Humidity
10% to 90% non-condensing
•
Shipping Temperature
-40º to 140ºF (-40º to 60ºC)
•
Shipping Humidity
10 to 90% non-condensing
Zebra ZXP Series 8 Card Printer User’s Manual
P1013772-001 Rev. A ( Draft 1 )
Technical Specifications
Declarations of Conformity
Declarations of Conformity
ZEBRA TECHNOLOGIES CORPORATION
Declares that the following Information Technology Equipment
Zebra ZXP Series 8 Card Printer
complies with following applicable directives and standards for the
ITE: Residential, Commercial & Light Industry environments
Applicable Directives and Supporting Standards:
2004/108/EC EMC Directive, EN55022:2006 Class A,
EN55024:1998+AD1:2001+AD2:2003EN, 61000-3-2:2006, EN61000-3-3:1995+AD1:2001,
2006/95/EC LVD Directive, EN60950-1:2001, CB Scheme
RFID Enabled
Applicable Directives and Supporting Standards:
99/5/EC R&TTE Directive, EN 301 489-3 V1.4.1 (2002-08), EN 300 220-2 V2.1.2 (2007-06)
For a formal certificate, please contact the Compliance Office at Zebra’s Camarillo facility.
EUROPE: Norway Only: This product is also designed for IT power system with phase to phase
voltage 230V. Earth grounding is via the polarized, 3-wire power cord.
FI: “Laite on liitettävä suojamaadoitus koskettimilla varustettuun pistorasiaan”
SE: “Apparaten skall anslutas till jordat uttag”
NO: “Apparatet må tilkoples jordet stikkontakt”
FCC Regulations
The Zebra ZXP Series 8 Card Printer has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and operated in accordance with the Zebra ZXP Series 8 Card
Printer User’s Manual, may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
Pursuant to Part 15.21 of the FCC Rules, any changes or modifications to this equipment not
expressly approved by Zebra may cause harmful interference and void the FCC authorization
to operate this equipment.
FCC Radiation Exposure Statement (applicable to 15.247 device only)
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum 20 cm between the radiator and your body. This transmitter must not be
collocated or operating in conjunction with any other antenna or transmitter unless
authorized to do so by the FCC.
Industry Canada Notice
This device complies with Industry Canada ICES-003 class A requirements.
Cet équipement est conforme à l 'ICES-003 classe A de la Norme Industrielle Canadienne.
P1013772-001 Rev. A ( Draft 1 )
Zebra ZXP Series 8 Card Printer User’s Manual
101
102
Zebra ZXP Series 8 Card Printer User’s Manual
P1013772-001 Rev. A ( Draft 1 )
APPENDIX A
Printer Configurations
Introduction
The Part Number of a particular printer is shown on a label affixed to the bottom of the printer;
that Part Number identifies the specific configuration for that printer. The chart on the
following page shows the configurations that are available.
P1013772-001 Rev. A ( Draft 1 )
Zebra ZXP Series 8 Card Printer User’s Manual
103
Printer Configurations
Part Numbers
PART NUMBER
DESCRIPTION
Z 8 _
104
Base Unit
_ _ 3
_ _ 4
_ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _
Dual-sided printing with single-sided lamination
Dual-sided printing with dual-sided lamination
_ _ _
_ _ _
_ _ _
0 _ _ _ _ _ _ _ _ _ _ _
A _ _ _ _ _ _ _ _ _ _ _
E _ _ _ _ _ _ _ _ _ _ _
Smart Card Options
None
Contact Encoder + Contactless MIFARE
Contact Station
_ _ _
_ _ _
_ 0 _ _ _ _ _ _ _ _ _ _
_ M _ _ _ _ _ _ _ _ _ _
Mag Encoders
None
ISO HiCo/LoCo Mag S/W Selectable
_ _ _
_ _ _
_ _ 0 _ _ _ _ _ _ _ _ _
_ _ A _ _ _ _ _ _ _ _ _
Security Options
None
Enclosure Lock
_ _ _
_ _ _ C _ _ _ _ _ _ _ _
Interface
USB and 10/100 Ethernet
_ _ _
_ _ _
_ _ _ _ 0 _ _ _ _ _ _ _
_ _ _ _ D _ _ _ _ _ _ _
Software/Kit
None
Media Starter Kit (includes: 1 YMCK ribbon kit, 1 roll of
InTM, 200 PVC cards)
_ _ _
_ _ _
_ _ _ _ _ 0 0 0 _ _ _ _
_ _ _ _ _ 0 0 A _ _ _ _
Miscellaneous
None
Made in America
_ _ _
_ _ _ _ _ _ _ _ 0 0 _ _
Custom Code
Reserved for future options
_ _ _
_ _ _ _ _ _ _ _ _ _ 0 0
Custom Code
Reserved for future options
Zebra ZXP Series 8 Card Printer User’s Manual
P1013772-001 Rev. A ( Draft 1 )
Appendix B
Connecting to a Network
Card printers can be connected to an Ethernet network in three ways.
Printer Sharing
In printer sharing, the printer is connected locally to the host computer and configured to be
shared to other client computers. Client computers connect to the printer over the network
through the host computer.
P1013772-001 Rev. A ( Draft 1 )
Zebra ZXP Series 8 Card Printer User’s Manual
105
Connecting to a Network
External Print Server
A stand alone device that acts as a server on the network specifically for receiving print jobs
and passing them to the printer. Client computers connect to the print server over a network.
Internal Print Server
Similar to an external print server, except the print server is integrated into the printer. This
removes the need for a separate power supply and separate device drivers. This is the simplest
way to network a printer.
106
Zebra ZXP Series 8 Card Printer User’s Manual
P1013772-001 Rev. A ( Draft 1 )
Appendix C
Magnetic Card Encoder
Introduction
This Appendix includes operation and maintenance requirements for Printers with the optional
magnetic card stripe encoder.
Mag Encoder (optional)
behind the idler roller
assembly door
The magnetic encoder can be set for either high or low coercivity. Use the printer driver to
change the encoder setting.
P1013772-001 Rev. A ( Draft 1 )
Zebra ZXP Series 8 Card Printer User’s Manual
107
Magnetic Card Encoder
Driver Setting
The Card Setup tab allows the user to specify the Magnetic Encoder Card Type in use.
Based on your selection, the printer automatically adjusts various printer properties for
optimum performance.
If your card type is not listed in the drop-down menu, select Custom and fill out the Card
Specifications pop-up screen.
To access the Card Setup Tab, select Start > Printers and Faxes. Right click on the Zebra ZXP
Series 8 Card Printer listing; and select Printing Preferences > Card Setup.
•
108
Make the appropriate Magnetic Encoder Card Type selection.
Zebra ZXP Series 8 Card Printer User’s Manual
P1013772-001 Rev. A ( Draft 1 )
Magnetic Card Encoder
Media Loading Orientation
Note • ONLY USE cards that comply with ISO 7810 and 7811 standards for magnetic stripe
cards. The magnetic stripe must be flush to the surface of the card to work properly.
Never use cards which have taped-on magnetic stripes.
Place the cards in the Input Hopper in the correct orientation as shown (with the magnetic
stripe down and facing to the rear). Ensure that the cards are seated properly the hopper.
P1013772-001 Rev. A ( Draft 1 )
Zebra ZXP Series 8 Card Printer User’s Manual
109
Magnetic Card Encoder
Magnetic Encoder Cleaning
The Magnetic Encoder is cleaned as part of the printer cleaning process; see Section 6. If the
frequency of encoding errors increases, the head may need additional cleaning. To cleans, only
use foam-tipped swabs.
Caution • Never use a sharp object or any abrasive to scrape deposits from the Magnetic
Encoder. Permanent damage to the Magnetic Head will result.
Step 1. Open the Door.
Step 2. Open the idler roller assembly door.
Step 3. Bend the Cleaning Swab to release the cleaning fluid.
Step 4. Clean the Magnetic Encoder by moving Cleaning Swab tip side-to-side across the
head elements. To re-order Cleaning Swabs, see the Media List on the User
Documentation and Drivers CD supplied with this printer.
Step 5. Close the idler roller assembly door.
Step 6. Close the Door.
110
Zebra ZXP Series 8 Card Printer User’s Manual
P1013772-001 Rev. A ( Draft 1 )
APPENDIX D
Smart Card Options
Introduction
This Appendix contains information on the additional operations of a Printer equipped with
one or more of the available Smart Card options.
Smart Card Encoder
(optional)
Smart Cards can have a built-in microcomputer and/or memory to store fingerprints, voice
recognition patterns, medical records, and other such data. All other printer operations remain
the same as the standard models.
P1013772-001 Rev. A ( Draft 1 )
Zebra ZXP Series 8 Card Printer User’s Manual
111
Smart Card Options
Encoding and Reading Smart Cards
Encoding data onto Smart Cards and reading the data previously encoded on them is totally
under control of the application software; no operator action is required.
If you experience any problems with encoding or reading data, refer to the users manual or
other documentation for the application software.
Driver Setting
The Card Setup tab allows the user to specify the Smart Card Type in use. Based on your
selection, the printer automatically adjusts various printer properties for optimum
printer performance.
If your card type is not listed in the drop-down menu, select Custom and fill out the Card
Specifications pop-up screen.
To access the Card Setup Tab, select Start > Printers and Faxes. Right click on the Zebra ZXP
Series 8 Card Printer listing; and select Printing Preferences > Card Setup.
•
112
Make the appropriate Smart Card Type selection.
Zebra ZXP Series 8 Card Printer User’s Manual
P1013772-001 Rev. A ( Draft 1 )
Smart Card Options
Contact Smart Cards
Contact Smart Cards have a pad of contacts on the surface of the card that connect to the
circuitry embedded into the card.
The printer responds to commands that position the card at the contact location, where the
printer connects to the contacts on the Smart Card. Data to be encoded onto the Smart Card,
and data read from the Smart Card, can interface via a connector on the printer’s rear panel
(Contact Station), or encoding/decoding can be performed by logic on the printer’s Main
PCBA (Contact Encoder).
All other printer operations remain the same as the standard models.
Media Loading Orientation for Contact Smart Cards
Place the cards in the Input Hopper in the correct orientation as shown (with the gold-plated
Smart Card contacts at the top surface of the card and facing to the left). Ensure that the cards
are seated properly the hopper.
P1013772-001 Rev. A ( Draft 1 )
Zebra ZXP Series 8 Card Printer User’s Manual
113
Smart Card Options
Contact Station Smart Card Interface
When a command to the printer interface sends a card to the Smart Card Contact Station, the
printer connects the Smart Card Contact Station to the female DB-9 connector on the rear of
the printer.
DB-9 Connector location for
Smart Card Contact Station
An attached external Smart Card Programmer can be used to program Smart Card chips. The
following table shows the Smart Card Contact Points.
114
Pin
Smart Card Contact Points
DB-9
Smart Card Contact Points
C1 (VCC)
C6 (Vpp)
C2 (Reset)
C7 (I/O)
C3 (Clock)
C8 (RFU)
C4 (RFU)
C5 (GND)
(GND when chip
is at station)
Zebra ZXP Series 8 Card Printer User’s Manual
P1013772-001 Rev. A ( Draft 1 )
Smart Card Options
Contactless Smart Cards
Rather than using a contact pad, Contactless Smart Cards use various short-range radio
technologies to “connect” to the printer. The printer moves the card to an antenna location
on the card path, and the encoding or decoding occurs. All other printer operations remain
the same.
Media Loading Orientation for Contactless Smart Cards
For Contactless Smart Cards, orientation is not a consideration.
Printing on Contactless Smart Cards
With reverse transfer printing technology, there are no restrictions when designing material to
be printed on Contactless Smart Cards.
P1013772-001 Rev. A ( Draft 1 )
Zebra ZXP Series 8 Card Printer User’s Manual
115
116
Zebra ZXP Series 8 Card Printer User’s Manual
P1013772-001 Rev. A ( Draft 1 )
Appendix E
Packing the Printer for
Shipment
Introduction
If the printer is to be shipped, it is important to use the original packing and shipping material
to prevent damage to the Printer.
If the original material is lost, a replacement Shipping Kit can be ordered from Zebra; refer to
the Media List on the User Documentation and Drivers CD supplied with this printer.
Procedure
Note • The specifics of the shipment and the printer’s condition may influence which of the
following steps are followed; common sense should prevail.
Step 1. Remove any cards from the Input and Output Hoppers.
Step 2. If the printer still has power applied and is turned on and is still connected to the
host computer, set the printer’s power switch (on the back of the printer) to the
OFF (
) position; and disconnect the interface and power cables to the printer.
Step 3. Open the printer Door.
Step 4. Remove the Print Ribbon and Transfer Film. (If you wish to save the print ribbon and
film for future use, you may want to put them in a plastic bag for storage.)
Step 5. Remove the Cleaning Cartridge and Cleaning Roller, and place them in the
foam insert.
Step 6. Close the printer Door.
P1013772-001 Rev. A ( Draft 1 )
Zebra ZXP Series 8 Card Printer User’s Manual
117
Packing the Printer for Shipment
Step 7. Remove the Input and Output Hopper, and place them in the foam insert.
Note • In the figure below, the printer and accessories are shown in the bottom foam insert,
out of the shipping carton for clarity.
Cleaning Roller
Cleaning Cartridge
Input Hopper
Output Hopper
Step 8. Place the Printer in its protective plastic bag.
Step 9. Place the lower foam insert in the Shipping Carton.
Step 10. Use both hands to carefully place the Printer into the recess in the lower foam insert.
Step 11. Place the upper foam insert onto the Printer, and gently press it down so it makes a
snug fit on the Printer -- the top of the upper foam insert should be even with the
upper edge of the Shipping Carton.
Step 12. Close the Shipping Carton.
Step 13. Tape the Shipping Carton securely.
118
Zebra ZXP Series 8 Card Printer User’s Manual
P1013772-001 Rev. A ( Draft 1 )
Appendix F
Worldwide Support
For Technical Support or Repair Services, contact the appropriate facility listed below.
North America and Latin America - Technical Support
Zebra Technologies Card Printer Solutions
1001 Flynn Road
Camarillo, CA 93012-8706 USA
Phone:
email:
+1 800 511 9909 (when calling from within the U.S.)
+1 805 577-7002, option 1 (when calling from Latin America)
techsupport@zebra.com
North America and Latin America - Repair Services
Before returning any equipment to Zebra Technologies Corporation for in-warranty or out-ofwarranty repair, contact Repair Services for a Return Materials Authorization (RMA) number.
Repack the equipment in the original packing material, and mark the RMA number clearly on
the outside. Ship the equipment, freight prepaid, to either address listed below:
Zebra Technologies Card Printer Solutions
1001 Flynn Road
Camarillo, CA 93012-8706 USA
Phone:
email:
+1 800 452 4034
+1 805 578 1201
repair-ca@zebra.com
Zebra Technologies Card Printer Repair Services
333 Corporate Woods Parkway
Vernon Hills, IL 60061
Phone:
email:
webform:
P1013772-001 Rev. A ( Draft 1 )
1-877-275-9327
repair@zebra.com
www.zebra.com/repair
Zebra ZXP Series 8 Card Printer User’s Manual
119
Worldwide Support
Europe, Middle East, and Africa - Technical Support
Zebra Technologies Card Printer Solutions
Dukes Meadow
Millboard Road, Bourne End
Buckinghamshire SL8 5XF, UK
Phone:
FAX:
e-mail:
+44 (0) 1628 556 000
+44 (0) 1628 556 001
cardts@zebra.com
Europe, Middle East, and Africa - Repair Services
Before returning any equipment to Zebra Technologies Corporation for in-warranty or out-ofwarranty repair, contact Repair Services for a Return Materials Authorization (RMA) number.
Repack the equipment in the original packing material, and mark the RMA number clearly on
the outside. Ship the equipment, freight prepaid, to the address listed below:
Zebra Technologies Card Printer Solutions
Pittman Way
Fulwood, Preston
Lancashire PR2 9ZD, UK
Phone:
FAX:
email:
+ 44 (0) 177 2 69 3069
+ 44 (0) 177 2 69 3046
ukrma@zebra.com
Asia Pacific - Technical Support and Repair Services
Before returning any equipment to Zebra Technologies Corporation for in-warranty or out-ofwarranty repair, contact Repair Services for a Return Materials Authorization (RMA) number.
Repack the equipment in the original packing material, and mark the RMA number clearly on
the outside. Ship the equipment, freight prepaid, to the address listed below:
Zebra Technologies Card Printer Solutions
120 Robinson Road
#06-01 Parakou Building
Singapore 068913
Phone:
e-mail:
+ 65 6885 0833
esoh@zebra.com
Website
www.zebracard.com
120
Zebra ZXP Series 8 Card Printer User’s Manual
P1013772-001 Rev. A ( Draft 1 )

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Page Mode                       : UseOutlines
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Format                          : application/pdf
Creator                         : tburton
Title                           : _Osprey_Lam_UM_RevA.book
Create Date                     : 2009:07:01 08:11:03Z
Creator Tool                    : FrameMaker 8.0
Modify Date                     : 2009:07:16 15:54:50-07:00
Metadata Date                   : 2009:07:16 15:54:50-07:00
Producer                        : Acrobat Distiller 9.0.0 (Windows)
Document ID                     : uuid:d1dcef15-66ff-4c48-8f35-06233f21a24e
Instance ID                     : uuid:5ee92201-fcc3-4a67-a715-926ed6a477da
Has XFA                         : No
Page Count                      : 50
Author                          : tburton

EXIF Metadata provided by EXIF.tools