Zero Energy Solutions CC2530 Zigbee module User Manual Manual

Download:
Mirror Download [FCC.gov]
Document ID	2933537
Application ID	ZFS8bNx6MoM2R4ep3p08IQ==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	28.41kB (355074 bits)
Date Submitted	2016-03-17 00:00:00
Date Available	2016-03-17 00:00:00
Creation Date	2015-03-20 16:41:55
Producing Software	Acrobat Distiller 9.0.0 (Windows)
Document Lastmod	2016-03-14 17:55:57
Document Title	Manual
Document Creator	PScript5.dll Version 5.2.2
Document Author:	bill

Zigbee Wireless Product
CC2530 Zigbee Module SZ1
·General Description
The SZ1 RF Module is a low-power, highly integrated 2.4-GHz transceiver that suitable
for systems targeting compliance with worldwide radio-frequency. It’s a true system-on-chip
solution for 2.4-GHz IEEE802.15.4,ZigBee applications.
·Electrical Characteristics
Ta = 25°C, VCC = 3.3V
ITEM
Voltage supply
Transmitting
current
Receiving
current
Sleep
consumption
frequency
Output power
Receiving
sensitivity
Data rate
Transmit
distance
Baud Rate
Operating
temperature
Package size
MIN
PARAMETER
TYPICAL
MAX
2.1
3.3
3.6
36
38
40
mA
25
26
27
mA
0.3
2.405
3.5
2400
4.0
UNIT
uA
2.485
4.2
GHz
dBm
-97
dBm
250
Kbps
150
9600
115200
bps
80
℃
-40
28×20×2 mm
Zigbee Wireless Product
Radio
·2.4-GHz IEEE802.15.4 compliant RF transceiver
·Excellent receiver sensitivity and robustness to Interference, receiver sensitivity reach to
-97dBm
·Programmable output power up to 4.5dBm
·Suitable for systems targeting compliance with worldwide radio-frequency
·Accurate digital RSSI/LQI support
·datarate: 250 kBps
8051 MCU
·Powerful five-channel DMA
·128KB in-system programmable flash, customization 32-,64-,256KB
·8KB RAM with retention in all power modes
·CSMA/CA hardware support
·AES security coprocessor
·Battery monitor and temperature sensor
·12-Bit ADC with eight channels and configurable resolution
·Two powerful USARTs with support for several serial protocols
·IEEE 802.15.4 MAC timer, general-purpose timers (One 16-Bit, Two 8-Bit)
·32-kHz sleep timer with capture
·Watchdog timer
·21 general-purpose I/O pins (19× 4 mA, 2×20 mA)
·Hardware debug support
·Package Description
Zigbee Wireless Product
·Pin Description
Pin name Pin type Description
Pin typ
Pin namee
VCC
Power
GND
Ground
RESET_N
reset
P0.0
Digital I/O
P0.1
Digital I/O
P0.2
Digital I/O
P0.3
Digital I/O
P0.4
Digital I/O
P0.5
Digital I/O
P0.6
Digital I/O
P0.7
Digital I/O
P1.0
Digital I/O
P1.1
Digital I/O
P1.2
Digital I/O
P1.3
Digital I/O
P1.4
Digital I/O
P1.5
Digital I/O
P1.6
Digital I/O
P1.7
Digital I/O
P2.0
Digital I/O
P2.1
Digital I/O
P2.2
Digital I/O
ANT
Antenna interface
Note:
1. P2.3 and P2.4 connect to a 32768 KHz crystal.
2. Spring Antenna or PCB Antenna can be choice.
3. Read TI CC2530 datasheet for detail.
Description
DC 2.0－3.6V
GND
CC2530 RESET
CC2530 P0.0
CC2530 P0.0
CC2530 P0.2
CC2530 P0.3
CC2530 P0.4
CC2530 P0.5
CC2530 P0.5
CC2530 P0.5
CC2530 P1.0
CC2530 P1.1
CC2530 P1.2
CC2530 P1.3
CC2530 P1.4
CC2530 P1.5
CC2530 P1.6
CC2530 P1.7
CC2530 P2.0
CC2530 P2.1
CC2530 P2.2
50ohm
TYWE1S DATASHEET
Regulatory information for the OEMs and Integrators
The guidelines described within this document are provided to OEM integrators installing
Zigbee module in notebook and tablet PC host platforms. Adherence to these requirements is necessary
to meet the conditions of compliance with FCC rules, including RF exposure. When all antenna type and
placement guidelines described herein are fulfilled the Zigbee module may be incorporated
into notebook and tablet PC host platforms with no further restrictions. If any of the guidelines described
herein are not satisfied it may be necessary for the OEM or integrator to perform additional testing
and/or obtain additional approval. The OEM or integrator is responsible to determine the required host
regulatory testing and/or obtaining the required host approvals for compliance
. Zigbee module are intended for OEMs and host integrators only.
. The Zigbee module must be operated with an access point that has been approved for the
country of operation.
. Changes or modification to Zigbee module by OEMs, integrators or other third parties is not
permitted. Any changes or modification to Zigbee module by OEMs, integrators or other third
parties will void authorization to operate
This module is not masked, and the end user needs to increase the mask.
Information to Be Supplied to the End User by the OEM or Integrator
The following regulatory and safety notices must be published in documentation supplied to the end user
of the product or system incorporating the Amplified Zigbee module, in compliance with local regulations.
Host system must be labeled with "Contains FCC ID: 2AHI9CC2530 ", FCC ID displayed on label.
The Zigbee module must be installed and used in strict accordance with the manufacturer's
instructions as described in the user documentation that comes with the product. Intel Corporation is not
responsible for any radio or television interference caused by unauthorized modification of the devices
included with the wireless adapter kit or the substitution or attachment of connecting cables and
equipment other than that specified by Intel Corporation. The correction of interference caused by such
unauthorized modification, substitution or attachment is the responsibility of the user. Intel Corporation
and authorized resellers or distributors are not liable for any damage or violation of government
regulations that may arise from the user failing to comply with these guidelines.
This device has been evaluated and shown compliant with the FCC RF Exposure limits under fixed
exposure conditions (antennas are greater than 20cm from a person’s body)when installed in certain
specific configurations.
The host system shall have a label showing: Contains FCC ID: 2AHI9CC2530
When the user selects U.FL RF connector antenna, it requires the a complete the antenna. the kind
of antenna that users can be use: 2.4 G RF antenna U.FL. RF connector(antenna type: FPC antenna,
Integral antenna）
(The gain of antenna : 2.0dBi)
TYWE1S DATASHEET
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause undesired operation.
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or
transmitter.
15.105 Information to the user.
(b) For a Class B digital device or peripheral, the instructions furnished the user shall include the following or
similar statement, placed in a prominent location in the text of the manual:
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator
and your body.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The availability of some specific channels and/or operational frequency bands are country dependent and are
firmware programmed at the factory to match the intended destination.
The firmware setting is not accessible by the end user.
The final end product must be labelled in a visible area with the following:
“Contains Transmitter Module 2AHI9&&2530”

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 5
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Producer                        : Acrobat Distiller 9.0.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2016:03:14 17:55:57+08:00
Create Date                     : 2015:03:20 16:41:55+08:00
Metadata Date                   : 2016:03:14 17:55:57+08:00
Format                          : application/pdf
Title                           : Microsoft Word - 中性 zigbee SZ1_En
Creator                         : bill
Document ID                     : uuid:c734e043-be22-4c50-8518-ad02a66bba6a
Instance ID                     : uuid:d2b1f379-f702-498b-a159-69971862b780
Author                          : bill

EXIF Metadata provided by EXIF.tools