Zhongshan K mate General Electronics BTE004 Bluetooth Mono Headset User Manual 4 BTE004 BC4
Zhongshan K-mate General Electronics Co., Ltd Bluetooth Mono Headset 4 BTE004 BC4
User Manual
BTE004 Bluetooth mono headset User Manual Brief introduction……………………………………….2 1. Bluetooth Wireless communication technology…………….2 2. About BTE004………………………………………………….2 Before using……………………………………………..2 1. Overview…………………………………………………………2 2. Charging the battery of the headset………………………….3 Basic operation…………………………………………..3 1. 2. 3. 4. 5. 6. 7. Switching on/off the headset……………………………………3 Pairing the headset with Bluetooth mobile phone…………….3 Wearing the headset……………………………………………..4 Changing the faceplate…………………………………………..5 The operation of the headset……………………………………6 LED indicator……………………………………………………..7 Indication tone…………………………………………………….7 Care and maintenance……………………………………7 Specification……………………………………………….8 Welcome to use this Bluetooth headset, BTE004. Please read this uer manual carefully before using it. Brief introduction 1. Bluetooth Wireless communication technology Bluetooth is a standard of close range radio communication technology that was drawn up by Ericsson, IBM, Internet, Nokia and Toshiba. Through Bluetooth technology, we can achieve the highest transmission rate among mobile phone, computer, printer, PDA and other devices. The max transmit range of class 2 is 10 meters while the max radio-communication range of class 1 can reach up to 100 meters. 2. About BTE004 BTE004 is a Bluetooth headset. It has the following features: Answer call, end call and reject call Redial last call Voice dial (The function needs your mobile phone to support) Adjust volume Voice transfer Microphone mute The function of changing faceplate Before using 1. Overview Multi-function button (MFB) Charging socket LED indicator light Microphone Volume up Volume down Loudspeaker Ear cap Ear hook 2. Charging the bettary of the headset First using—You must charge the battery of the headset fully before first using. Low power—The red indicator light will flash and you can also hear 3 tones of “DU” every 20 seconds. At this time, you have to charge the battery of the headset. The charging steps are as follows: Step1: Connect charger or charging cable to standard power outlet; Step2: Connect the end of charger or charging cable to charging socket of the headset; Step3: When charging, red indicator light is on. It takes about 1 1.5 hours to charge the battery fully; Step4: When charging has completed, the red indicator light will switch off. Note: If charging via a USB port, this USB port is used only for charging purposes, no any data is transferred over the USB port. Warning: 1. The battery is recycled. 2. Do not dispose of the battery in fire, as it may cause Explosion. Basic operation 1. Switching on/off the headset LED indicator Indication tone light Switch on the Long press MFB for 3 indicator A long “DI” and a 5 Blue headset light is on for 1 long “DU” tones seconds, and release it till second indicator light is on Switch off the Long press MFB for 3 indicator A long “DI” tone 5 Red headset seconds, and release it till light is on for 1 second and indicator light is off then all indicator lights are off Enter into When the headset is off, long Red and blue Nothing pairing mode press MFB for 7 8 seconds LEDs flash alternately Remark: The headset will switch off automatically if no devices can be connected after 10 minutes in order to save power. Function Operation 2. Pairing the headset with Bluetooth mobile phone You have to pair the Bluetooth headset with Bluetooth mobile phone before first using the headset. Please make sure your mobile phone has bluetooth function that is available. Specific pairing procedures may vary with different mobile phones. Please refer to your mobile phone user manual for further information. The steps are as follows: 1) Keep the headset and Bluetooth mobile phone within 1 meter when pairing. 2) Make sure your headset is off. 3) Press MFB for about 7 8 seconds, then release it till you see the red and blue indicator lights to flash alternately or hear indication tone for three times (The first tone is “DI”, the second one is “DU” and the third one is “Dong-dong”). The headset entered into pairing mode. 4) Switch on Bluetooth function of mobile phone and search the Bluetooth device. After searched, select “BTE004” in the Bluetooth device list. 5) According to indication, enter password or PIN No:”1234”, and press the key of ” Yes” or “confirm”. 6) After successful pairing, select “BTE004” in the Bluetooth device list, and press “connect”. After successful connecting, the indicator light will flash twice every 4 seconds. Remark: The pairing mode will last 2 minutes. The headset will switch to standby mode automatically if it can’t pair with any devices after 2 minutes. If you want to continue to pair the headset with Bluetooth device, please switch off the headset firstly, and then re-pair according to steps 1 6 mentioned above. After pairing is successful, the headset and mobile phone will remember each other, no need to re-pair when use next time. When you switch on the headset every time, it will connect with last connected device automatically. If you want to pair it with other devices, please switch off Bluetooth function of last connected devices firstly, then pair the headset with new device according to steps 1 6 mentioned above. 3. Wearing the headset This headset is suitable for both ears. The ear hook can turn freely. After wearing the headset well, please turn the microphone of the headset towards to the mouth of user, the effect of conversation will be better. Suitable for right ear Suitable for left ear 4. Changing the faceplate 1) . Take down the faceplate 2) . Install new faceplate 5. The operation of the headset Function Cancel calling Answer call The status of the headset Calling Ringing Ringing Operation Short press MFB once to cancel calling Short press MFB once Long press MFB for about 2 seconds, and Reject call release it till hearing indication tone Conversation mode End call Short press MFB once Conversation mode Volume up Short press volume + Conversation mode Volume down Short press volume Conversation mode Long press volume+ button for about 2 Voice transfer seconds, and then release it till hearing indication tone Conversation mode Press simultaneously volume+ button and volume – button for about 2 seconds, and Microphone then release them till hearing indication mute tone. When the microphone is mute, the headset sounds a short “DU” tone every 5 seconds Conversation mode Press simultaneously volume+ button and Cancel mute (microphone mute) volume - button for about 2 seconds, and then release them till hearing indication tone Standby mode (already Long press VOL + button for about 2 Voice dial connected with Bluetooth seconds, and then release it till hearing device) indication tone Standby mode (already Redial last connected with Bluetooth Short press MFB 2 times call device) Warning: Excessive pressure from earphones and headsets can cause hearing loss. Remarks: Not all the mobile phones support all the functions listed above. Please refer to your mobile phone user manual for further information. Some functions and indication tones may vary with different mobile phones. For some mobile phones, when you press the answer button on the phone, the conversation will be sent to the mobile phone. At this time, you may switch the call to the headset through the conversation switching function of the headset or operating on your mobile phone. Please refer to your mobile phone user manual for further information. 6. LED indicator light 1) When it is charging LED indicator light The red indicator light is on The red indicator light is off 2) The status of the headset Charging Finish charging When it is not charging LED indicator light The status of the headset The red and blue indicator lights flash alternately The blue indicator light flashes 1 time every 1 seconds The blue indicator light flashes 2 times every 4 seconds The blue indicator flashes 1 time every 1 seconds The blue indicator light flashes quickly The red indicator light flashes Pairing mode Standby mode (not connected with Bluetooth device) Standby mode (already connected with Bluetooth device) Coming call/calling Conversation mode Low power 7. indication tone Indication tone It sounds a tone of “DU” every 5 seconds It sounds three tones of ‘’DU” every 20 seconds Care and maintenance The status of the headset Microphone mute Low power Please read the following suggestions carefully, that will help you to fulfill any warranty obligations and enjoy this product for many years. Keep dry and don’t put it in the dump place, so as not to affecting the interior circuit of product. Don’t put the product under the sunlight or place in hot areas. High temperature will shorten the life of electronic device, destroy the battery, or distort certain plastic. Don’t expose the product in the cold areas. It may damage the internal circuit board. Don’t try to take apart the product. It may damage the product if you are not professional. Don’t fall off on the floor or knock the hard substance. It may damage interior circuit. Don’t use intensify chemical or detergent to clean the product. Don’t scrap the surface with sharp things. If the product can’t work normally, please send it to the regularly asserted store. The staff will help you to solve the problem warmly. Specification Bluetooth version Bluetooth profiles Bluetooth V2.0 Headset, Handsfree Frequency response 2.4GHz 2.4835GHz Effective range 10m Working time 6-7hours Standby time 100 hours Charging input DC 5V 90mA Charging time About 1.5 hours Working temperature -20 Storage temperature -20~70 Dimension 57*16*9mm Headset: 9g Ear hook: 1g Weight 55 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Page Count : 8 Producer : GNU Ghostscript 7.06 Title : Microsoft Word - 4 BTE004_BC4_ user manual.doc Creator : PScript5.dll Version 5.2.2 Create Date : 11/17/2009 13:45:47 Author : dufEXIF Metadata provided by EXIF.tools