87295 NZ 20012NZ SD Extreme WR Handryer
2016-12-16
: Zip Water 87295 - Wr Handryer 20012Nz Sd Extreme Nz 87295 - WR_Handryer 20012NZ SD Extreme_NZ zenithwater. manuals zenithwater. washroom zenithwater.products zenithwater.nz
Open the PDF directly: View PDF .
Page Count: 4
Download | |
Open PDF In Browser | View PDF |
Installation Instructions and Operating Procedure Superdry Extreme Touch-free automatic electric hand dryer 20012NZ - Superdry Extreme with Cast Alloy Case Superdry Installation & Operating Instructions 87295 - February 2010 Page 1 1. SPECIFICATIONS : 2. PACKING LIST : Activation Activated by an Infrared sensor. The machine operates automatically. Dimensions WxHxD 326 x 254 x 188 mm (12.8” x 10” x 7.4”) Voltage/Power 220-240V, 50Hz, 2000- 2200W Detection Distance 180 + 20mm (7.0” + 0.78”) Kodak White Scale Operation Duration 60 sec (Self protection automatic shutoff) Motor Type Induction Type (Brushless) Illustration Description Security Wrench Installation Instruction Installation Template 1 2 3 4 Hand Dryer Qty Illustration 1 Pc 5 1 Pc 6 Description Plastic Dowel Fixing Screw Qty 4 Pcs 4 Pcs 1 Pc 7 Washer 4 Pcs 1 Set 8 Power Cord 1 Pc This machine is equipped with Infrared sensor for automatic activation. 3. STANDARD INSTALLATION : 2 Mens’ washroom 1065 mm Ladies’ washroom 1015 mm Disabled washroom 800 mm 1 ITEM 1 DESCRIPTION PCB CONTROL KIT 4. BEFORE INSTALLATION : 4.1 Make sure the sensor is located 60cm (23inches) above everything below to prevent false triggers due to reflection. 5. INSTALLATION STEPS: 5.1.1 Remove the cover from the hand dryer by unscrewing the two side screws and lift the cover off. 4.2 Never install hand dryer onto a wooden or plastic wall finish. 5.1.2 Paste the Installation Template at the appropriate location on the wall. 4.3 Before installation, make sure the power source complies with specification of the machine and local requirement and that the power cord can reach the power outlet. 5.1.3 Drill four ø9mm holes and insert plastic dowels. EMPTY ZONE Min 60cm ø9mm Page 2 KIT NO. 99128 5.2 Insert Screws into dowels and tighten them. 5.3 The hand dryer unit comes with a flexible power cord and plug. 5.4 For concealed wiring, drill hole on wall using template for rear cable entry. Wire to 220-240V AC power source rated at 10 Amps. Superdry Installation & Operating Instructions 87295 - February 2010 6. INSTALLATION CHECK : 6.1 Insert security screws and tighten them. 6.2 Plug into power outlet and check power is ON. Adjust sensor range here 7. OPERATION INSTRUCTIONS : 7.1 The machines starts operating automatically when user’s hands are put approximately 80mm (3.15”) below the sensor located next to the air louvre. Whenever the hands are moved out of the sensing range, the machine will stop after approximately 0.5 seconds 7.2 The 0.5 second time delay helps avoid false triggers by unexpected movements. 7.3 When the air temperature is over 120ºC or any fault has occurred, the thermal cut-out will shut off the power to the heater. 7.4 For safety reasons, the machine will immediately stop operating when it is used continuously for 60 seconds. The machine returns to standard function when hands are moved away. 8. ADJUSTMENT OF SENSOR : 8.1 Turn off power first. 8.2 Loosen Security Screws and remove the Aluminum Housing. (Use the Security Wrench from the supplied package in the carton.) 8.3 Refer to drawing shown in Section 6 for the location of the sensor range adjustment device . 8.4 Use a tiny flat screw driver to turn adjustment screw in clockwise direction to lengthen the sensing distance. To shorten the sensing distance turn in counter-clockwise direction. 8.5 After finishing the adjustment, put back the aluminum housing and fasten it. Sensor range adjustment 9. WIRING DIAGRAM : 10. IMPORTANT NOTICE : Gray POWER Blue Brown Green/Yellow C MOTOR hi W L N Bk te Red Black OVERLOAD HEATER PCB Black Black Red White Blue Gray Black SENSOR PCB INFRARED SENSOR 10.1 Turn off power supply prior to removing outer case. 10.2 Turn off power supply before maintenance or cleaning. If aluminium housing or air louvre are covered with dust, do not splash water onto it. Use only damp sponge or cloth to wipe dirt off. 10.3 Never try to put a small screwdriver or any other object into the holes of the air louvre from outside. This might cause damage to the interior parts, and electric shock may occur. 10.4 Keep sensor case clean, never use any abrasive cleaning agent, rough surface articles, steel brush or sand paper to rub the sensor case. This will make the sensor case dull and decrease the sensitivity of the sensor. 10.5 For safety, do not dry other objects except hands. 10.6 Do not allow young children, handicapped or infirm persons to use the Hand Dryer without supervision. 10.7 If any cord or plug is damaged, it must be repaired only by a qualified technician. 10.8 To avoid hazards, all installation procedures must be carried out by a suitably qualified tradesperson. 11. TROUBLE SHOOTING (FOR QUALIFIED ELECTRICIAN USE ONLY) : Problem Hand dryer does not work. Diagnosis Solution Check power supply is on. Turn on the power The sensor cable is unplugged. Connect the cable properly. Sensing distance too short. Adjust sensing distance as per Section 8. Sensor Assy or Power cord out of order. Cold air without heat. Heater out of order. Contact the vendor for service. Motor out of order. No air but heat. Motor condenser out of order. Superdry Installation & Operating Instructions 87295 - February 2010 Page 3 Contact Information Registering your product: Registering your installation on the Zenith Heaters Limited website may help to establish date of installation, should it become necessary to service the appliance, under the terms of Zenith Heaters Limited warranty. To register your installation go to www.zenithheaters.co.nz and look under the heading “Warranty”. As Zenith Heaters Limited policy is one of continuous product improvement, changes to specifications may be made without prior notice. Images in this booklet have been modified and may not be true representations of the finished goods. The use of this crossed out wheeled bin logo indicates that this product needs to be disposed of separately to any other household waste. Within each of the European Union member countries, provisions have been made for the collection and recycling of unwanted electrical and electronic equipment. Outside of the EU it will be necessary to dispose of this product at your local community waste collection or recycling centre. In order to help preserve our environment we ask that you dispose of this product correctly. Please contact your local city council for collection centre details Head Office Zenith Heaters Limited, Unit 2/15 Moselle Avenue, Henderson. Auckland. 0610 New Zealand. www.zenithheaters.co.nz Telephone: 0800 558055 Facsimile: 0800 559055 Page 4 Superdry- Installation & Operating Instructions - 87295 - February 2010
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Author : davidl Create Date : 2010:02:15 13:40:14+11:00 Modify Date : 2010:02:15 13:40:14+11:00 XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Format : application/pdf Title : 87295 NZ 20012NZ - SD Extreme .indd Creator : davidl Creator Tool : PScript5.dll Version 5.2.2 Producer : Acrobat Distiller 9.3.0 (Windows) Document ID : uuid:53d24717-2e67-46d5-8835-048f8bc0e412 Instance ID : uuid:2cd3907a-2668-486c-9c6a-cbb4a6c4c337 Page Count : 4EXIF Metadata provided by EXIF.tools