Vent Tray Kit 93540 And 93541

2016-08-17

: Zip Water Vent Tray Kit 93540 And 93541.Indd Vent Tray Kit 93540 and 93541 zipwater.manuals zipwater.hydrotaps zipwater.products zipwater.australia

Open the PDF directly: View PDF PDF.
Page Count: 1

DownloadVent Tray Kit 93540 And 93541
Open PDF In BrowserView PDF
ZIP Vent Tray Kit Installation
NOTE: The Vent Tray Kits 93540 (for BC and BCS models) and 93541 (for C and CS models) are both
installed in the same way.
1.

2.

3.

4.

5.

6.

7.

8.
9.

Before installing the Vent Tray Kit.
Ensure the 4mm silicon door buffers are fitted
to the inside of the cupboard doors to allow
sufficient air to enter the cupboard space.
If there is insufficient air flow through the
cupboard, an air inlet grill (not supplied) will
need to be fitted to the upper part of the door or
to an exterior wall of the same cupboard space.
For marking purposes, place the assembled vent
tray kit in a suitable position on the cupboard
floor. Check there will be sufficient clearance
around, the final placement of, the undersink
unit and that the undersink unit will be close to
the Hydrotap hose and tube connections, as
specified in the main installation instructions.
With the vent tray assembly in position, secure
the outlet duct section to the front of the
cupboard floor, using the two small screws
supplied.
Adjust the depth of the main box section by
sliding the box back to suit the size of your
undersink unit. Check both sides of the box are
square with the outlet duct section.
Mark the final position of the main box on the
cupboard floor and then remove the outlet
duct section to reveal all four of the main box
mounting locations.
With the main box in place (check against the
marks made in step 5) mark and drill out the 4
main box mounting locations.
With the vent tray assembly removed from the
cupboard, cut an outlet vent into the front edge
of the cupboard floor so that it is located evenly
between the two screw holes made in step 3.
The cut out should be between 300-450mm wide
and cut back close to the kickboard (nominal
43mm).
Replace the main box and secure in place with
the 4 large screws supplied.
Refit the outlet duct section to the front of the
main box and secure in place with the 2 small
screws supplied (as in step 3).

Head Office
Zip Heaters (Aust) Pty. Ltd.
ABN: 46 000 578 727
67 Allingham Street
Condell Park NSW 2200
Postal: Locked Bag 80
Bankstown 1885 Australia

Zip G4 Vent Tray Kit

Website:
www.zipindustries.com
Facsimile: (02) 9796 3858
Telephone: (02) 9796 3100
Sales & Service.
Free Call: 1 800 63 86 33
Customer Care.
Free Call: 1 800 42 43 44

93540 assembled
vent tray kit
2

Main Box
4

3
Outlet Duct

300-450mm
cut out
7

Finished assembly

9

June 2015 v1.00
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 1
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
Producer                        : PDF Printer / www.bullzip.com / CP / Freeware Edition
Modify Date                     : 2015:06:18 14:13:41+10:00
Create Date                     : 2015:06:18 14:13:41+10:00
Creator Tool                    : UnknownApplication
About                           : e6b68a18-17cb-11e5-0000-e06f4b0064f.ØÈ£.2015-06-18T14:13:41+10:00
Document ID                     : uuid:e6b68a18-17cb-11e5-0000-e06f4b0064f•.wçÒc..
Format                          : application/pdf
Title                           : Vent Tray Kit 93540 and 93541.indd
Creator                         : davidl
Author                          : davidl
EXIF Metadata provided by EXIF.tools

Navigation menu