ZyXEL Communications VMG4380B10A Wireles N VDSL2 4-port Bonding Combo WAN Gateway with HPNA User Manual Manual 2

ZyXEL Communications Corporation Wireles N VDSL2 4-port Bonding Combo WAN Gateway with HPNA Manual 2

Contents

Manual 2

Chapter 11 Network Address Translation (NAT)VMG4380-B10A / VMG4325-B10A User’s Guide 18111.3 The Applications ScreenThis screen provides a summary of all NAT applications and their configuration. In addition, this screen allows you to create new applications and/or remove existing ones.To access this screen, click Network Setting > NAT > Applications. The following screenappears.Figure 78 Network Setting > NAT > ApplicationsThe following table describes the labels in this screen. End Port Enter the last port of the original destination port range. To forward only one port, enter the port number in the Start Port field above and then enter it again in this field. To forward a series of ports, enter the last port number in a series that begins with the portnumber in the Start Port field above.TranslationStart PortThis shows the port number to which you want the Device to translate the incoming port.For a range of ports, enter the first number of the range to which you want the incomingports translated.Translation EndPortThis shows the last port of the translated port range.Server IP AddressEnter the inside IP address of the virtual server here.Protocol Select the protocol supported by this virtual server. Choices are TCP, UDP, or TCP/UDP.OK Click OK to save your changes.Cancel Click Cancel to exit this screen without saving.Table 54 Port Forwarding: Add/Edit (continued)LABEL DESCRIPTIONTable 55 Network Setting > NAT > ApplicationsLABEL DESCRIPTIONAdd new applicationClick this to add a new NAT application rule.ApplicationForwardedThis field shows the type of application that the service forwards.WAN Interface This field shows the WAN interface through which the service is forwarded.Server IP AddressThis field displays the destination IP address for the service.Modify Click the Delete icon to delete the rule.
Chapter 11 Network Address Translation (NAT)VMG4380-B10A / VMG4325-B10A User’s Guide18211.3.1 Add New ApplicationThis screen lets you create new NAT application rules. Click Add new application in theApplications screen to open the following screen.Figure 79 Applications: Add The following table describes the labels in this screen. 11.4 The Port Triggering ScreenSome services use a dedicated range of ports on the client side and a dedicated range of ports onthe server side. With regular port forwarding you set a forwarding port in NAT to forward a service (coming in from the server on the WAN) to the IP address of a computer on the client side (LAN). The problem is that port forwarding only forwards a service to a single LAN IP address. In order to use the same service on a different LAN computer, you have to manually replace the LAN computer's IP address in the forwarding port with another LAN computer's IP address. Trigger port forwarding solves this problem by allowing computers on the LAN to dynamically taketurns using the service. The Device records the IP address of a LAN computer that sends traffic to the WAN to request a service with a specific port number and protocol (a "trigger" port). When the Device's WAN port receives a response with a specific port number and protocol ("open" port), the Device forwards the traffic to the LAN IP address of the computer that sent the request. After that computer’s connection for that service closes, another computer on the LAN can use the service in the same manner. This way you do not need to configure a new IP address each time you want a different LAN computer to use the application.Table 56 Applications: AddLABEL DESCRIPTIONWAN Interface Select the WAN interface that you want to apply this NAT rule to.Server IP AddressEnter the inside IP address of the application here.ApplicationCategorySelect the category of the application from the drop-down list box.ApplicationForwardedSelect a service from the drop-down list box and the Device automatically configures theprotocol, start, end, and map port number that define the service.View Rule Click this to display the configuration of the service that you have chosen in ApplicationFowarded.OK Click OK to save your changes.Cancel Click Cancel to exit this screen without saving.
Chapter 11 Network Address Translation (NAT)VMG4380-B10A / VMG4325-B10A User’s Guide 183For example:Figure 80 Trigger Port Forwarding Process: Example1Jane requests a file from the Real Audio server (port 7070).2Port 7070 is a “trigger” port and causes the Device to record Jane’s computer IP address. The Device associates Jane's computer IP address with the "open" port range of 6970-7170.3The Real Audio server responds using a port number ranging between 6970-7170.4The Device forwards the traffic to Jane’s computer IP address.5Only Jane can connect to the Real Audio server until the connection is closed or times out. The Device times out in three minutes with UDP (User Datagram Protocol) or two hours with TCP/IP (Transfer Control Protocol/Internet Protocol). Click Network Setting > NAT > Port Triggering to open the following screen. Use this screen to view your Device’s trigger port settings.Figure 81 Network Setting > NAT > Port Triggering The following table describes the labels in this screen. Table 57 Network Setting > NAT > Port TriggeringLABEL DESCRIPTIONAdd new rule Click this to create a new rule.# This is the index number of the entry.Status This field displays whether the port triggering rule is active or not. A yellow bulb signifies that this rule is active. A gray bulb signifies that this rule is not active.Service Name This field displays the name of the service used by this rule.WAN Interface This field shows the WAN interface through which the service is forwarded.Trigger Start PortThe trigger port is a port (or a range of ports) that causes (or triggers) the Device to record the IP address of the LAN computer that sent the traffic to a server on the WAN.This is the first port number that identifies a service.Trigger End PortThis is the last port number that identifies a service.Trigger Proto. This is the trigger transport layer protocol.
Chapter 11 Network Address Translation (NAT)VMG4380-B10A / VMG4325-B10A User’s Guide18411.4.1 Add/Edit Port Triggering Rule This screen lets you create new port triggering rules. Click Add new rule in the Port Triggeringscreen or click a rule’s Edit icon to open the following screen.Figure 82 Port Triggering: Add/Edit The following table describes the labels in this screen. Open Start Port The open port is a port (or a range of ports) that a server on the WAN uses when it sends out a particular service. The Device forwards the traffic with this port (or range of ports) tothe client computer on the LAN that requested the service.This is the first port number that identifies a service.Open End Port This is the last port number that identifies a service.Open Proto. This is the open transport layer protocol.Modify Click the Edit icon to edit this rule.Click the Delete icon to delete an existing rule. Table 57 Network Setting > NAT > Port Triggering (continued)LABEL DESCRIPTIONTable 58 Port Triggering: Configuration Add/EditLABEL DESCRIPTIONActive Select the check box to enable this rule.Service Name Enter a name to identify this rule using keyboard characters (A-Z, a-z, 1-2 and so on). WAN Interface Select a WAN interface for which you want to configure port triggering rules.Trigger Start PortThe trigger port is a port (or a range of ports) that causes (or triggers) the Device to record the IP address of the LAN computer that sent the traffic to a server on the WAN.Type a port number or the starting port number in a range of port numbers.Trigger End PortType a port number or the ending port number in a range of port numbers.Trigger Protocol Select the transport layer protocol from TCP, UDP, or TCP/UDP.
Chapter 11 Network Address Translation (NAT)VMG4380-B10A / VMG4325-B10A User’s Guide 18511.5 The DMZ ScreenIn addition to the servers for specified services, NAT supports a default server IP address. A default server receives packets from ports that are not specified in the NAT Port Forwarding Setupscreen.Figure 83 Network Setting > NAT > DMZ The following table describes the fields in this screen. Open Start Port The open port is a port (or a range of ports) that a server on the WAN uses when it sends out a particular service. The Device forwards the traffic with this port (or range of ports) tothe client computer on the LAN that requested the service.Type a port number or the starting port number in a range of port numbers.Open End Port Type a port number or the ending port number in a range of port numbers.Open Protocol Select the transport layer protocol from TCP, UDP, or TCP/UDP.OK Click OK to save your changes.Cancel Click Cancel to exit this screen without saving.Table 58 Port Triggering: Configuration Add/Edit (continued)LABEL DESCRIPTIONTable 59 Network Setting > NAT > DMZLABEL DESCRIPTIONDefault ServerAddressEnter the IP address of the default server which receives packets from ports that are notspecified in the NAT Port Forwarding screen. Note: If you do not assign a Default Server Address, the Device discards all packetsreceived for ports that are not specified in the NAT Port Forwarding screen.Apply Click Apply to save your changes.Cancel Click Cancel to restore your previously saved settings.
Chapter 11 Network Address Translation (NAT)VMG4380-B10A / VMG4325-B10A User’s Guide18611.6 The ALG ScreenSome NAT routers may include a SIP Application Layer Gateway (ALG). A SIP ALG allows SIP calls to pass through NAT by examining and translating IP addresses embedded in the data stream.When the Device registers with the SIP register server, the SIP ALG translates the Device’s privateIP address inside the SIP data stream to a public IP address. You do not need to use STUN or an outbound proxy if your Device is behind a SIP ALG.Use this screen to enable and disable the NAT and SIP (VoIP) ALG in the Device. To access this screen, click Network Setting > NAT > ALG.Figure 84 Network Setting > NAT > ALGThe following table describes the fields in this screen.11.7 The Address Mapping ScreenOrdering your rules is important because the Device applies the rules in the order that you specify.When a rule matches the current packet, the Device takes the corresponding action and the remaining rules are ignored. Click Network Setting > NAT > Address Mapping to display the following screen. Figure 85 Network Setting > NAT > Address MappingTable 60 Network Setting > NAT > ALGLABEL DESCRIPTIONNAT ALG Enable this to make sure applications such as FTP and file transfer in IM applications work correctly with port-forwarding and address-mapping rules.SIP ALG Enable this to make sure SIP (VoIP) works correctly with port-forwarding and address-mapping rules.Apply Click Apply to save your changes.Cancel Click Cancel to restore your previously saved settings.
Chapter 11 Network Address Translation (NAT)VMG4380-B10A / VMG4325-B10A User’s Guide 187The following table describes the fields in this screen.11.7.1 Add/Edit Address Mapping RuleTo add or edit an address mapping rule, click Add new rule or the rule’s edit icon in the AddressMapping screen to display the screen shown next. Figure 86 Address Mapping: Add/EditTable 61 Network Setting > NAT > Address MappingLABEL DESCRIPTIONAdd new rule Click this to create a new rule.Set This is the index number of the address mapping set.Local Start IP This is the starting Inside Local IP Address (ILA).Local End IP This is the ending Inside Local IP Address (ILA). If the rule is for all local IP addresses, thenthis field displays 0.0.0.0 as the Local Start IP address and 255.255.255.255 as the LocalEnd IP address. This field is blank for One-to-One mapping types.Global Start IP This is the starting Inside Global IP Address (IGA). Enter 0.0.0.0 here if you have a dynamic IP address from your ISP. You can only do this for the Many-to-One mapping type. Global End IP This is the ending Inside Global IP Address (IGA). This field is blank for One-to-One and Many-to-One mapping types.Type This is the address mapping type.One-to-One: This mode maps one local IP address to one global IP address. Note that portnumbers do not change for the One-to-one NAT mapping type.Many-to-One: This mode maps multiple local IP addresses to one global IP address. This is equivalent to SUA (i.e., PAT, port address translation), the Device's Single User Account feature that previous routers supported only. Many-to-Many: This mode maps multiple local IP addresses to shared global IP addresses.Modify Click the Edit icon to go to the screen where you can edit the address mapping rule.Click the Delete icon to delete an existing address mapping rule. Note that subsequentaddress mapping rules move up by one when you take this action.
Chapter 11 Network Address Translation (NAT)VMG4380-B10A / VMG4325-B10A User’s Guide188The following table describes the fields in this screen.11.8 Technical ReferenceThis part contains more information regarding NAT.11.8.1 NAT DefinitionsInside/outside denotes where a host is located relative to the Device, for example, the computers of your subscribers are the inside hosts, while the web servers on the Internet are the outside hosts. Global/local denotes the IP address of a host in a packet as the packet traverses a router, for example, the local address refers to the IP address of a host when the packet is in the local network, while the global address refers to the IP address of the host when the same packet is traveling in the WAN side. Table 62 Address Mapping: Add/EditLABEL DESCRIPTIONType Choose the IP/port mapping type from one of the following.One-to-One: This mode maps one local IP address to one global IP address. Note that portnumbers do not change for the One-to-one NAT mapping type.Many-to-One: This mode maps multiple local IP addresses to one global IP address. This is equivalent to SUA (i.e., PAT, port address translation), the Device's Single User Account feature that previous routers supported only. Many-to-Many: This mode maps multiple local IP addresses to shared global IP addresses.Local Start IP Enter the starting Inside Local IP Address (ILA).Local End IP Enter the ending Inside Local IP Address (ILA). If the rule is for all local IP addresses, then this field displays 0.0.0.0 as the Local Start IP address and 255.255.255.255 as the LocalEnd IP address. This field is blank for One-to-One mapping types.Global Start IP Enter the starting Inside Global IP Address (IGA). Enter 0.0.0.0 here if you have a dynamic IP address from your ISP. You can only do this for the Many-to-One mapping type. Global End IP Enter the ending Inside Global IP Address (IGA). This field is blank for One-to-One andMany-to-One mapping types.Set Select the number of the mapping set for which you want to configure.OK Click OK to save your changes.Cancel Click Cancel to exit this screen without saving.
Chapter 11 Network Address Translation (NAT)VMG4380-B10A / VMG4325-B10A User’s Guide 189Note that inside/outside refers to the location of a host, while global/local refers to the IP address of a host used in a packet. Thus, an inside local address (ILA) is the IP address of an inside host ina packet when the packet is still in the local network, while an inside global address (IGA) is the IP address of the same inside host when the packet is on the WAN side. The following table summarizes this information.NAT never changes the IP address (either local or global) of an outside host.11.8.2 What NAT DoesIn the simplest form, NAT changes the source IP address in a packet received from a subscriber (the inside local address) to another (the inside global address) before forwarding the packet to the WAN side. When the response comes back, NAT translates the destination address (the inside global address) back to the inside local address before forwarding it to the original inside host. Notethat the IP address (either local or global) of an outside host is never changed.The global IP addresses for the inside hosts can be either static or dynamically assigned by the ISP.In addition, you can designate servers, for example, a web server and a telnet server, on your local network and make them accessible to the outside world. If you do not define any servers (for Many-to-One and Many-to-Many Overload mapping), NAT offers the additional benefit of firewall protection. With no servers defined, your Device filters out all incoming inquiries, thus preventingintruders from probing your network. For more information on IP address translation, refer to RFC1631, The IP Network Address Translator (NAT).Table 63 NAT DefinitionsITEM DESCRIPTIONInside This refers to the host on the LAN.Outside This refers to the host on the WAN.Local This refers to the packet address (source or destination) as the packet travels on theLAN.Global This refers to the packet address (source or destination) as the packet travels on theWAN.
Chapter 11 Network Address Translation (NAT)VMG4380-B10A / VMG4325-B10A User’s Guide19011.8.3 How NAT WorksEach packet has two addresses – a source address and a destination address. For outgoing packets, the ILA (Inside Local Address) is the source address on the LAN, and the IGA (Inside Global Address) is the source address on the WAN. For incoming packets, the ILA is the destination address on the LAN, and the IGA is the destination address on the WAN. NAT maps private (local) IP addresses to globally unique ones required for communication with hosts on other networks. It replaces the original IP source address (and TCP or UDP source port numbers for Many-to-One and Many-to-Many Overload NAT mapping) in each packet and then forwards it to the Internet. The Device keeps track of the original addresses and port numbers so incoming reply packets can have their original values restored. The following figure illustrates this.Figure 87 How NAT Works192.168.1.13192.168.1.10192.168.1.11192.168.1.12 SA192.168.1.10SAIGA1Inside LocalIP Address192.168.1.10192.168.1.11192.168.1.12192.168.1.13Inside Global IP AddressIGA 1IGA 2IGA 3IGA 4NAT TableWANLANInside LocalAddress (ILA)Inside GlobalAddress (IGA)
Chapter 11 Network Address Translation (NAT)VMG4380-B10A / VMG4325-B10A User’s Guide 19111.8.4 NAT ApplicationThe following figure illustrates a possible NAT application, where three inside LANs (logical LANs using IP alias) behind the Device can communicate with three distinct WAN networks.Figure 88 NAT Application With IP AliasPort Forwarding: Services and Port NumbersThe most often used port numbers are shown in the following table. Please refer to RFC 1700 for further information about port numbers. Please also refer to the Supporting CD for more examples and details on port forwarding and NAT.Table 64 Services and Port NumbersSERVICES PORT NUMBERECHO 7FTP (File Transfer Protocol) 21SMTP (Simple Mail Transfer Protocol) 25DNS (Domain Name System) 53Finger 79HTTP (Hyper Text Transfer protocol or WWW, Web) 80POP3 (Post Office Protocol) 110NNTP (Network News Transport Protocol) 119SNMP (Simple Network Management Protocol) 161SNMP trap 162PPTP (Point-to-Point Tunneling Protocol) 1723
Chapter 11 Network Address Translation (NAT)VMG4380-B10A / VMG4325-B10A User’s Guide192Port Forwarding ExampleLet's say you want to assign ports 21-25 to one FTP, Telnet and SMTP server (A in the example),port 80 to another (B in the example) and assign a default server IP address of 192.168.1.35 to a third (C in the example). You assign the LAN IP addresses and the ISP assigns the WAN IP address. The NAT network appears as a single host on the Internet.Figure 89 Multiple Servers Behind NAT ExampleD=192.168.1.36192.168.1.1IP address assigned by ISPA=192.168.1.33B=192.168.1.34C=192.168.1.35
VMG4380-B10A / VMG4325-B10A User’s Guide 193CHAPTER 12Dynamic DNS Setup12.1 Overview DNSDNS (Domain Name System) is for mapping a domain name to its corresponding IP address and vice versa. The DNS server is extremely important because without it, you must know the IP address of a machine before you can access it. In addition to the system DNS server(s), each WAN interface (service) is set to have its own static or dynamic DNS server list. You can configure a DNS static route to forward DNS queries for certain domain names through a specific WAN interface to its DNS server(s). The Device uses a system DNS server (in the order you specify in the Broadband screen) to resolve domain names that do not match any DNS routing entry. After the Device receives a DNS reply from a DNS server, it creates a new entry for the resolved IP address in the routing table.Dynamic DNSDynamic DNS allows you to update your current dynamic IP address with one or many dynamic DNS services so that anyone can contact you (in NetMeeting, CU-SeeMe, etc.). You can also access your FTP server or Web site on your own computer using a domain name (for instance myhost.dhs.org, where myhost is a name of your choice) that will never change instead of using an IP address that changes each time you reconnect. Your friends or relatives will always be able to call you even if they don't know your IP address.First of all, you need to have registered a dynamic DNS account with www.dyndns.org. This is for people with a dynamic IP from their ISP or DHCP server that would still like to have a domain name. The Dynamic DNS service provider will give you a password or key.12.1.1 What You Can Do in this Chapter• Use the DNS Entry screen to view, configure, or remove DNS routes (Section 12.2 on page194).• Use the Dynamic DNS screen to enable DDNS and configure the DDNS settings on the Device (Section 12.3 on page 195).
Chapter 12 Dynamic DNS SetupVMG4380-B10A / VMG4325-B10A User’s Guide19412.1.2 What You Need To KnowDYNDNS WildcardEnabling the wildcard feature for your host causes *.yourhost.dyndns.org to be aliased to the same IP address as yourhost.dyndns.org. This feature is useful if you want to be able to use, for example, www.yourhost.dyndns.org and still reach your hostname.If you have a private WAN IP address, then you cannot use Dynamic DNS.12.2 The DNS Entry ScreenUse this screen to view and configure DNS routes on the Device. Click Network Setting > DNS to open the DNS Entry screen.Figure 90 Network Setting > DNS > DNS EntryThe following table describes the fields in this screen. Table 65 Network Setting > DNS > DNS EntryLABEL DESCRIPTIONAdd new DNS entryClick this to create a new DNS entry.# This is the index number of the entry.Hostname This indicates the host name or domain name.IP Address This indicates the IP address assigned to this computer.Modify Click the Edit icon to edit the rule.Click the Delete icon to delete an existing rule.
Chapter 12 Dynamic DNS SetupVMG4380-B10A / VMG4325-B10A User’s Guide 19512.2.1 Add/Edit DNS EntryYou can manually add or edit the Device’s DNS name and IP address entry. Click Add new DNS entry in the DNS Entry screen or the Edit icon next to the entry you want to edit. The screen shown next appears.Figure 91 DNS Entry: Add/EditThe following table describes the labels in this screen. 12.3 The Dynamic DNS ScreenUse this screen to change your Device’s DDNS. Click Network Setting > DNS > Dynamic DNS. The screen appears as shown.Figure 92 Network Setting > DNS > Dynamic DNSTable 66 DNS Entry: Add/EditLABEL DESCRIPTIONHost Name Enter the host name of the DNS entry.IP Address Enter the IP address of the DNS entry.Apply Click Apply to save your changes.Cancel Click Cancel to exit this screen without saving.
Chapter 12 Dynamic DNS SetupVMG4380-B10A / VMG4325-B10A User’s Guide196The following table describes the fields in this screen. Table 67 Network Setting > DNS > > Dynamic DNSLABEL DESCRIPTIONDynamic DNS Select Enable to use dynamic DNS.ServiceProviderSelect your Dynamic DNS service provider from the drop-down list box.Hostname Type the domain name assigned to your Device by your Dynamic DNS provider.You can specify up to two host names in the field separated by a comma (",").Username Type your user name.Password Type the password assigned to you.Email If you select TZO in the Service Provider field, enter the user name you used to register for this service.Key If you select TZO in the Service Provider field, enter the password you used to register for this service.Apply Click Apply to save your changes.Cancel Click Cancel to exit this screen without saving.
VMG4380-B10A / VMG4325-B10A User’s Guide 197CHAPTER 13Interface Group13.1 OverviewBy default, all LAN and WAN interfaces on the Device are in the same group and can communicate with each other. Create interface groups to have the Device assign the IP addresses in different domains to different groups. Each group acts as an independent network on the Device. This lets devices connected to an interface group’s LAN interfaces communicate through the interface group’s WAN or LAN interfaces but not other WAN or LAN interfaces.13.1.1 What You Can Do in this ChapterThe Interface Group screens let you create multiple networks on the Device (Section 13.2 on page 197).13.2 The Interface Group ScreenYou can manually add a LAN interface to a new group. Alternatively, you can have the Device automatically add the incoming traffic and the LAN interface on which traffic is received to an interface group when its DHCP Vendor ID option information matches one listed for the interface group.Use the LAN screen to configure the private IP addresses the DHCP server on the Device assigns to the clients in the default and/or user-defined groups. If you set the Device to assign IP addresses based on the client’s DHCP Vendor ID option information, you must enable DHCP server and configure LAN TCP/IP settings for both the default and user-defined groups. See Chapter 8 on page 131 for more information.
Chapter 13 Interface GroupVMG4380-B10A / VMG4325-B10A User’s Guide198In the following example, the client that sends packets with the DHCP Vendor ID option set to MSFT5.0 (meaning it is a Windows 2000 DHCP client) is assigned the IP address 192.168.2.2 and uses the WAN VDSL_PoE/ppp0.1 interface.Figure 93 Interface Grouping ApplicationClick Network Setting > Interface Group to open the following screen.Figure 94 Network Setting > Interface Group The following table describes the fields in this screen. 13.2.1 Interface Group ConfigurationClick the Add New Interface Group button in the Interface Group screen to open the following screen. Use this screen to create a new interface group.Table 68 Network Setting > Interface GroupLABEL DESCRIPTIONAdd New Interface GroupClick this button to create a new interface group.Group Name This shows the descriptive name of the group.WAN Interface This shows the WAN interfaces in the group.LAN Interfaces This shows the LAN interfaces in the group.Criteria This shows the filtering criteria for the group.Modify Click the Delete icon to remove the group.Add Click this button to create a new group.Default: ETH 2~4Internet192.168.1.x/24192.168.2.x/24VDSL_PoE/ppp0.1eth10.0DHCP Vendor ID option: MSFT 5.0
Chapter 13 Interface GroupVMG4380-B10A / VMG4325-B10A User’s Guide 199Note: An interface can belong to only one group at a time.Figure 95 Interface Group Configuration The following table describes the fields in this screen. Table 69 Interface Group ConfigurationLABEL DESCRIPTIONGroup Name Enter a name to identify this group. You can enter up to 30 characters. You can use letters,numbers, hyphens (-) and underscores (_). Spaces are not allowed.WAN Interface used in the groupingSelect the WAN interface this group uses. The group can have up to one PTM interface and up to one ATM interface.Select None to not add a WAN interface to this group.Grouped LAN InterfacesAvailable LAN InterfacesSelect one or more LAN interfaces (Ethernet LAN, HPNA or wireless LAN) in the Available LAN Interfaces list and use the left arrow to move them to the Grouped LAN Interfaceslist to add the interfaces to this group.To remove a LAN or wireless LAN interface from the Grouped LAN Interfaces, use the right-facing arrow.Automatically Add Clients With thefollowing DHCPVendor IDsClick Add to identify LAN hosts to add to the interface group by criteria such as the type of the hardware or firmware. See Section 13.2.2 on page 200 for more information.# This shows the index number of the rule.Filter Criteria This shows the filtering criteria. The LAN interface on which the matched traffic is received will belong to this group automatically.WildCard SupportThis shows if wildcard on DHCP option 60 is enabled.
Chapter 13 Interface GroupVMG4380-B10A / VMG4325-B10A User’s Guide20013.2.2 Interface Grouping CriteriaClick the Add button in the Interface Grouping Configuration screen to open the following screen.Figure 96 Interface Grouping Criteria The following table describes the fields in this screen. Remove Click the Remove icon to delete this rule from the Device.Apply Click Apply to save your changes back to the Device.Cancel Click Cancel to exit this screen without saving.Table 69 Interface Group Configuration (continued)LABEL DESCRIPTIONTable 70 Interface Grouping CriteriaLABEL DESCRIPTIONSource MACAddressEnter the source MAC address of the packet.DHCP Option60Select this option and enter the Vendor Class Identifier (Option 60) of the matched traffic,such as the type of the hardware or firmware.Enable wildcard on DHCPoption 60optionSelect this option to be able to use wildcards in the Vendor Class Identifier configured for DHCP option 60.DHCP Option61Select this and enter the device identity of the matched traffic.IAID Enter the Identity Association Identifier (IAID) of the device, for example, the WAN connection index number.
Chapter 13 Interface GroupVMG4380-B10A / VMG4325-B10A User’s Guide 201DUID type Select DUID-LLT (DUID Based on Link-layer Address Plus Time) to enter the hardware type, a time value and the MAC address of the device.Select DUID-EN (DUID Assigned by Vendor Based upon Enterprise Number) to enter the vendor’s registered enterprise number.Select DUID-LL (DUID Based on Link-layer Address) to enter the device’s hardware type and hardware address (MAC address) in the following fields.Select Other to enter any string that identifies the device in the DUID field.DHCP Option125Select this and enter vendor specific information of the matched traffic.Enterprise Number Enter the vendor’s 32-bit enterprise number registered with the IANA (Internet Assigned Numbers Authority).Manufacturer OUI Specify the vendor’s OUI (Organization Unique Identifier). It is usually the first three bytesof the MAC address.ProductClass Enter the product class of the device.Model Name Enter the model name of the device.Serial Number Enter the serial number of the device.Apply Click Apply to save your changes back to the Device.Cancel Click Cancel to exit this screen without saving.Table 70 Interface Grouping Criteria (continued)LABEL DESCRIPTION
Chapter 13 Interface GroupVMG4380-B10A / VMG4325-B10A User’s Guide202
VMG4380-B10A / VMG4325-B10A User’s Guide 203CHAPTER 14USB Service14.1 Overview The Device has a USB port used to share files via a USB memory stick or a USB hard drive. In the USB Service screens, you can enable file-sharing server, media server, and printer server.14.1.1 What You Can Do in this Chapter• Use the File Sharing screen to enable file-sharing server (Section 14.2 on page 204). • Use the Media Server screen to enable or disable the sharing of media files (Section 14.3 onpage 206).• Use the Printer Server screen to enable the print server (Section 14.4 on page 207).14.1.2 What You Need To KnowThe following terms and concepts may help as you read this chapter.14.1.2.1 About File SharingWorkgroup nameThis is the name given to a set of computers that are connected on a network and share resources such as a printer or files. Windows automatically assigns the workgroup name when you set up a network. SharesWhen settings are set to default, each USB device connected to the Device is given a folder, called a “share”. If a USB hard drive connected to the Device has more than one partition, then eachpartition will be allocated a share. You can also configure a “share” to be a sub-folder or file on the USB device.File SystemsA file system is a way of storing and organizing files on your hard drive and storage device. Often different operating systems such as Windows or Linux have different file systems. The file sharing feature on your Device supports File Allocation Table (FAT) and FAT32.Common Internet File SystemThe Device uses Common Internet File System (CIFS) protocol for its file sharing functions. CIFScompatible computers can access the USB file storage devices connected to the Device. CIFS
Chapter 14 USB ServiceVMG4380-B10A / VMG4325-B10A User’s Guide204protocol is supported on Microsoft Windows, Linux Samba and other operating systems (refer to your systems specifications for CIFS compatibility). 14.1.2.2 About Printer ServerPrint ServerThis is a computer or other device which manages one or more printers, and which sends print jobs to each printer from the computer itself or other devices.Operating SystemAn operating system (OS) is the interface which helps you manage a computer. Common examplesare Microsoft Windows, Mac OS or Linux.TCP/IPTCP/IP (Transmission Control Protocol/ Internet Protocol) is a set of communications protocols that most of the Internet runs on. PortA port maps a network service such as http to a process running on your computer, such as a process run by your web browser. When traffic from the Internet is received on your computer, the port number is used to identify which process running on your computer it is intended for.Supported OSsYour operating system must support TCP/IP ports for printing and be compatible with the RAW (port 9100) protocol.The following OSs support Device’s printer sharing feature.• Microsoft Windows 95, Windows 98 SE (Second Edition), Windows Me, Windows NT 4.0, Windows 2000, Windows XP or Macintosh OS X.14.2 The File Sharing ScreenYou can share files on a USB memory stick or hard drive connected to your Device with users on your network.
Chapter 14 USB ServiceVMG4380-B10A / VMG4325-B10A User’s Guide 205The following figure is an overview of the Device’s file server feature. Computers A and B can access files on a USB device (C) which is connected to the Device.Figure 97 File Sharing OverviewThe Device will not be able to join the workgroup if your local area network has restrictions set up that do not allow devices to join a workgroup. In this case, contact your networkadministrator.14.2.1 Before You BeginMake sure the Device is connected to your network and turned on.1Connect the USB device to one of the Device’s USB port. Make sure the Device is connected to your network.2The Device detects the USB device and makes its contents available for browsing. If you areconnecting a USB hard drive that comes with an external power supply, make sure it is connectedto an appropriate power source that is on.Note: If your USB device cannot be detected by the Device, see the troubleshooting for suggestions.Use this screen to set up file sharing using the Device. To access this screen, click Network Setting > USB Service > File Sharing.Figure 98 Network Setting > USB Service > File SharingABC
Chapter 14 USB ServiceVMG4380-B10A / VMG4325-B10A User’s Guide206Each field is described in the following table.14.3 The Media Server ScreenThe media server feature lets anyone on your network play video, music, and photos from the USB storage device connected to your Device (without having to copy them to another computer). The Device can function as a DLNA-compliant media server. The Device streams files to DLNA-compliant media clients (like Windows Media Player). The Digital Living Network Alliance (DLNA) is a group ofpersonal computer and electronics companies that works to make products compatible in a home network.The Device media server enables you to:• Publish all shares for everyone to play media files in the USB storage device connected to the Device.• Use hardware-based media clients like the DMA-2500 to play the files. Note: Anyone on your network can play the media files in the published shares. No user name and password or other form of security is used. The media server is enabled by default with the video, photo, and music shares published.To change your Device’s media server settings, click Network Setting > USB Service > Media Server. The screen appears as shown.Figure 99 Network Setting > USB Service > Media ServerTable 71 Network Setting > Home Networking > File SharingLABEL DESCRIPTIONFile Sharing ServicesSelect Enable to activate file sharing through the Device. Host Name Enter the host name on the share.Apply Click Apply to save your changes.Cancel Click Cancel to restore your previously saved settings.
Chapter 14 USB ServiceVMG4380-B10A / VMG4325-B10A User’s Guide 207The following table describes the labels in this menu.14.4 The Printer Server ScreenThe Device allows you to share a USB printer on your LAN. You can do this by connecting a USBprinter to one of the USB ports on the Device and then adding the printer on the computers connected to your network. See Section 4.11 on page 62 for instructions on adding a printer on your computer.Figure 100 Sharing a USB Printer14.4.1 Before You BeginTo configure the print server you need the following:• Your Device must be connected to your computer and any other devices on your network. TheUSB printer must be connected to your Device.• A USB printer with the driver already installed on your computer.• See Section 4.11 on page 62 for instructions on adding a printer on your computer. Note: Your printer’s installation instructions may ask that you connect the printer to your computer. Connect your printer to the Device instead.Use this screen to enable or disable sharing of a USB printer via your Device. Table 72 Network Setting > USB Service > Media ServerLABEL DESCRIPTIONMedia Server Select Enable to have the Device function as a DLNA-compliant media server.Enable the media server to let (DLNA-compliant) media clients on your network play media files located in the shares.Apply Click Apply to save your changes.Cancel Click Cancel to restore your previously saved settings.
Chapter 14 USB ServiceVMG4380-B10A / VMG4325-B10A User’s Guide208To access this screen, click Network Setting > USB Service > Printer Server.Figure 101 Network Setting > USB Service > Printer ServerThe following table describes the labels in this menu.Table 73 Network Setting > USB Service > Print ServerLABEL DESCRIPTIONPrinter Server Select Enable to have the Device share a USB printer.Printer Name Enter the name of the printer.Make andmodelEnter the manufacturer and model number of the printer.Apply Click Apply to save your changes.Cancel Click Cancel to restore your previously saved settings.
VMG4380-B10A / VMG4325-B10A User’s Guide 209CHAPTER 15Firewall15.1 OverviewThis chapter shows you how to enable and configure the Device’s security settings. Use the firewall to protect your Device and network from attacks by hackers on the Internet and control access to it. By default the firewall:• allows traffic that originates from your LAN computers to go to all other networks. • blocks traffic that originates on other networks from going to the LAN. The following figure illustrates the default firewall action. User A can initiate an IM (Instant Messaging) session from the LAN to the WAN (1). Return traffic for this session is also allowed (2). However other traffic initiated from the WAN is blocked (3 and 4).Figure 102 Default Firewall Action15.1.1 What You Can Do in this Chapter• Use the General screen to configure the security level of the firewall on the Device (Section 15.2 on page 211).• Use the Service screen to add or remove predefined Internet services and configure firewall rules (Section 15.3 on page 211).• Use the Access Control screen to view and configure incoming/outgoing filtering rules (Section 15.4 on page 213). • Use the DoS screen to activate protection against Denial of Service (DoS) attacks (Section 15.5on page 216).WANLAN3412A
Chapter 15 FirewallVMG4380-B10A / VMG4325-B10A User’s Guide21015.1.2 What You Need to KnowSYN AttackA SYN attack floods a targeted system with a series of SYN packets. Each packet causes the targeted system to issue a SYN-ACK response. While the targeted system waits for the ACK that follows the SYN-ACK, it queues up all outstanding SYN-ACK responses on a backlog queue. SYN-ACKs are moved off the queue only when an ACK comes back or when an internal timer terminates the three-way handshake. Once the queue is full, the system will ignore all incoming SYN requests, making the system unavailable for legitimate users.DoSDenials of Service (DoS) attacks are aimed at devices and networks with a connection to the Internet. Their goal is not to steal information, but to disable a device or network so users no longer have access to network resources. The ZyXEL Device is pre-configured to automatically detect and thwart all known DoS attacks.DDoSA DDoS attack is one in which multiple compromised systems attack a single target, thereby causing denial of service for users of the targeted system.LAND AttackIn a LAND attack, hackers flood SYN packets into the network with a spoofed source IP address of the target system. This makes it appear as if the host computer sent the packets to itself, makingthe system unavailable while the target system tries to respond to itself.Ping of DeathPing of Death uses a "ping" utility to create and send an IP packet that exceeds the maximum 65,536 bytes of data allowed by the IP specification. This may cause systems to crash, hang or reboot.SPIStateful Packet Inspection (SPI) tracks each connection crossing the firewall and makes sure it is valid. Filtering decisions are based not only on rules but also context. For example, traffic from the WAN may only be allowed to cross the firewall in response to a request from the LAN.
Chapter 15 FirewallVMG4380-B10A / VMG4325-B10A User’s Guide 21115.2 The Firewall ScreenUse this screen to set the security level of the firewall on the Device. Firewall rules are grouped based on the direction of travel of packets to which they apply.Click Security > Firewall to display the General screen. Figure 103 Security > Firewall > GeneralThe following table describes the labels in this screen.15.3 The Service Screen You can configure customized services and port numbers in the Service screen. For a comprehensive list of port numbers and services, visit the IANA (Internet Assigned Number Authority) website. See Appendix F on page 349 for some examples. Table 74 Security > Firewall > GeneralLABEL DESCRIPTIONFirewall Select Enable to activate the firewall feature on the Device.Easy Select Easy to allow LAN to WAN and WAN to LAN packet directions.Medium Select Medium to allow LAN to WAN but deny WAN to LAN packet directions.High Select High to deny LAN to WAN and WAN to LAN packet directions.Apply Click Apply to save your changes.Cancel Click Cancel to restore your previously saved settings.
Chapter 15 FirewallVMG4380-B10A / VMG4325-B10A User’s Guide212Click Security > Firewall > Service to display the following screen.Figure 104 Security > Firewall > Service The following table describes the labels in this screen. 15.3.1 Add/Edit a Service Use this screen to add a customized service rule that you can use in the firewall’s ACL ruleconfiguration. Click Add new service entry or the edit icon next to an existing service rule in the Service screen to display the following screen.Figure 105 Service: Add/EditTable 75 Security > Firewall > ServiceLABEL DESCRIPTIONAdd new service entryClick this to add a new service.Name This is the name of your customized service.Description This is the description of your customized service.Ports/ProtocolNumberThis shows the IP protocol (TCP, UDP, ICMP, or TCP/UDP) and the port number or range of ports that defines your customized service. Other and the protocol number displays if the service uses another IP protocol.Modify Click the Edit icon to edit the entry.Click the Delete icon to remove this entry.
Chapter 15 FirewallVMG4380-B10A / VMG4325-B10A User’s Guide 213The following table describes the labels in this screen.15.4 The Access Control ScreenClick Security > Firewall > Access Control to display the following screen. This screen displays a list of the configured incoming or outgoing filtering rules. Figure 106 Security > Firewall > Access Control Table 76 Service: Add/EditLABEL DESCRIPTIONProtocol Choose the IP protocol (TCP, UDP, ICMP, or Other) that defines your customized port from the drop-down list box. Select Other to be able to enter a protocol number.Source/Destination PortThese fields are displayed if you select TCP or UDP as the IP port. Select Single to specify one port only or Range to specify a span of ports that define your customized service. If you select Any, the service is applied to all ports.Type a single port number or the range of port numbers that define your customized service.Protocol NumberThis field is displayed if you select Other as the protocol.Enter the protocol number of your customized port. Add Click this to add the protocol to the Rule List below.Rule ListProtocol This is the IP port (TCP, UDP, ICMP, or Other) that defines your customized port.Ports/ProtocolNumberFor TCP, UDP, ICMP, or TCP/UDP protocol rules this shows the port number or range thatdefines the custom service. For other IP protocol rules this shows the protocol number. Modify Click the Delete icon to remove the rule.Service Name Enter a unique name (up to 32 printable English keyboard characters, including spaces) foryour customized port.ServiceDescriptionEnter a description for your customized port.Apply Click Apply to save your changes.Cancel Click Cancel to exit this screen without saving.
Chapter 15 FirewallVMG4380-B10A / VMG4325-B10A User’s Guide214The following table describes the labels in this screen. Table 77 Security > Firewall > Access ControlLABEL DESCRIPTIONDoS Protection DoS (Denial of Service) attacks can flood your Internet connection with invalid packets andconnection requests, using so much bandwidth and so many resources that Internet accessbecomes unavailable. Select the Enable check box to enable protection against DoS attacks.Add new ACLruleClick this to go to add a filter rule for incoming or outgoing IP traffic.# This is the index number of the entry.Name This displays the name of the rule.Src IP This displays the source IP addresses to which this rule applies. Please note that a blank source address is equivalent to Any.Dst IP This displays the destination IP addresses to which this rule applies. Please note that a blank destination address is equivalent to Any.Service This displays the transport layer protocol that defines the service and the direction of traffic to which this rule applies.Action This field displays whether the rule silently discards packets (DROP), discards packets and sends a TCP reset packet or an ICMP destination-unreachable message to the sender(REJECT) or allows the passage of packets (ACCEPT).Modify Click the Edit icon to edit the rule.Click the Delete icon to delete an existing rule. Note that subsequent rules move up by onewhen you take this action.Click the Move To icon to change the order of the rule. Enter the number in the # field.
Chapter 15 FirewallVMG4380-B10A / VMG4325-B10A User’s Guide 21515.4.1 Add/Edit an ACL Rule Click Add new ACL rule or the Edit icon next to an existing ACL rule in the Access Control screen. The following screen displays.Figure 107 Access Control: Add/EditThe following table describes the labels in this screen.Table 78 Access Control: Add/EditLABEL DESCRIPTIONFilter Name Enter a descriptive name of up to 16 alphanumeric characters, not including spaces, underscores, and dashes. You must enter the filter name to add an ACL rule. This field is read-only if you are editing the ACL rule.Order Select the order of the ACL rule.Select SourceDeviceSelect the source device to which the ACL rule applies. If you select Specific IP Address, enter the source IP address in the field below.Source IPAddressEnter the source IP address.SelectDestination DeviceSelect the destination device to which the ACL rule applies. If you select Specific IPAddress, enter the destiniation IP address in the field below.Destination IPAddressEnter the destination IP address.
Chapter 15 FirewallVMG4380-B10A / VMG4325-B10A User’s Guide21615.5 The DoS ScreenDoS (Denial of Service) attacks can flood your Internet connection with invalid packets and connection requests, using so much bandwidth and so many resources that Internet access becomes unavailable. Use the DoS screen to activate protection against DoS attacks. Click Security > Firewall > DoS to display the following screen. Figure 108 Security > Firewall > DoSIP Type Select whether your IP type is IPv4 or IPv6. Select Protocol Select the transport layer protocol that defines your customized port from the drop-down list box. The specific protocol rule sets you add in the Security > Firewall > Service >Add screen display in this list.If you want to configure a customized protocol, select Specific Service.Protocol This field is displayed only when you select Specific Protocol in Select Protocol.Choose the IP port (TCP/UDP, TCP, UDP, ICMP, or ICMPv6) that defines your customizedport from the drop-down list box.Custom Source PortThis field is displayed only when you select Specific Protocol in Select Protocol.Enter a single port number or the range of port numbers of the source.CustomDestination PortThis field is displayed only when you select Specific Protocol in Select Protocol.Enter a single port number or the range of port numbers of the destination.Policy Use the drop-down list box to select whether to discard (DROP), deny and send an ICMPdestination-unreachable message to the sender of (REJECT) or allow the passage of (ACCEPT) packets that match this rule.Direction Use the drop-down list box to select the direction of traffic to which this rule applies.Enable RateLimitSelect this check box to set a limit on the upstream/downstream transmission rate for the specified protocol.Specify how many packets per minute or second the transmission rate is.Scheduler Rules Select a schedule rule for this ACL rule form the drop-down list box. You can configure a new schedule rule by click Add New Rule. This will bring you to the Security > Scheduler Rules screen.Apply Click Apply to save your changes.Cancel Click Cancel to exit this screen without saving.Table 78 Access Control: Add/Edit (continued)LABEL DESCRIPTION
Chapter 15 FirewallVMG4380-B10A / VMG4325-B10A User’s Guide 217The following table describes the labels in this screen. Table 79 Security > Firewall > DoSLABEL DESCRIPTIONDoS Protection BlockingSelect Enable to enable protection against DoS attacks.Deny Ping ResponseSelect Enable to block ping request packets. Apply Click Apply to save your changes.Cancel Click Cancel to exit this screen without saving.
Chapter 15 FirewallVMG4380-B10A / VMG4325-B10A User’s Guide218
VMG4380-B10A / VMG4325-B10A User’s Guide 219CHAPTER 16MAC Filter16.1 Overview You can configure the Device to permit access to clients based on their MAC addresses in the MAC Filter screen. This applies to wired and wireless connections. Every Ethernet device has a uniqueMAC (Media Access Control) address. The MAC address is assigned at the factory and consists of six pairs of hexadecimal characters, for example, 00:A0:C5:00:00:02. You need to know the MAC addresses of the devices to configure this screen.16.2 The MAC Filter ScreenUse this screen to allow wireless and LAN clients access to the Device. Click Security > MAC Filter. The screen appears as shown.Figure 109 Security > MAC Filter
Chapter 16 MAC FilterVMG4380-B10A / VMG4325-B10A User’s Guide220The following table describes the labels in this screen. Table 80 Security > MAC FilterLABEL DESCRIPTIONMAC Address Filter Select Enable to activate the MAC filter function.Set This is the index number of the MAC address.Allow Select Allow to permit access to the Device. MAC addresses not listed will be deniedaccess to the Device.If you clear this, the MAC Address field for this set clears.Host name Enter the host name of the wireless or LAN clients that are allowed access to the Device.MAC Address Enter the MAC addresses of the wireless or LAN clients that are allowed access to the Device in these address fields. Enter the MAC addresses in a valid MAC address format, that is, six hexadecimal character pairs, for example, 12:34:56:78:9a:bc.Apply Click Apply to save your changes.Cancel Click Cancel to restore your previously saved settings.
VMG4380-B10A / VMG4325-B10A User’s Guide 221CHAPTER 17Parental Control17.1 OverviewParental control allows you to block web sites with the specific URL. You can also define time periods and days during which the Device performs parental control on a specific user. 17.2 The Parental Control ScreenUse this screen to enable parental control, view the parental control rules and schedules.Click Security > Parental Control to open the following screen. Figure 110 Security > Parental Control The following table describes the fields in this screen. Table 81 Security > Parental ControlLABEL DESCRIPTIONParentalControlSelect Enable to activate parental control.Add new PCP Click this if you want to configure a new parental control rule.# This shows the index number of the rule.Status This indicates whether the rule is active or not.A yellow bulb signifies that this rule is active. A gray bulb signifies that this rule is not active.PCP Name This shows the name of the rule.Home NetworkUser (MAC)This shows the MAC address of the LAN user’s computer to which this rule applies.
Chapter 17 Parental ControlVMG4380-B10A / VMG4325-B10A User’s Guide22217.2.1 Add/Edit a Parental Control RuleClick Add new PCP in the Parental Control screen to add a new rule or click the Edit icon next to an existing rule to edit it. Use this screen to configure a restricted access schedule and/or URL filtering settings to block the users on your network from accessing certain web sites.Figure 111 Parental Control Rule: Add/Edit Internet AccessScheduleThis shows the day(s) and time on which parental control is enabled.Network ServiceThis shows whether the network service is configured. If not, None will be shown.Website Block This shows whether the website block is configured. If not, None will be shown.Modify Click the Edit icon to go to the screen where you can edit the rule.Click the Delete icon to delete an existing rule.Apply Click Apply to save your changes.Cancel Click Cancel to restore your previously saved settings.Table 81 Security > Parental Control (continued)LABEL DESCRIPTION
Chapter 17 Parental ControlVMG4380-B10A / VMG4325-B10A User’s Guide 223The following table describes the fields in this screen. Table 82 Parental Control Rule: Add/EditLABEL DESCRIPTIONGeneralActive Select the checkbox to activate this parental control rule.ParentalControl ProfileNameEnter a descriptive name for the rule.Home NetworkUserSelect the LAN user that you want to apply this rule to from the drop-down list box. If you select Custom, enter the LAN user’s MAC address. If you select All, the rule applies to all LAN users.Internet Access ScheduleDay Select check boxes for the days that you want the Device to perform parental control.Time Drag the time bar to define the time that the LAN user is allowed access. Network ServiceNetwork Service SettingIf you select Block, the Device prohibits the users from viewing the Web sites with the URLs listed below.If you select Allow, the Device blocks access to all URLs except ones listed below.Add new serviceClick this to show a screen in which you can add a new service rule. You can configure theService Name, Protocol, and Name of the new rule.# This shows the index number of the rule. Select the checkbox next to the rule to activate it.Service Name This shows the name of the rule.Protocol:Port This shows the protocol and the port of the rule.Modify Click the Edit icon to go to the screen where you can edit the rule.Click the Delete icon to delete an existing rule.Blocked Site/URL KeywordClick Add to show a screen to enter the URL of web site or URL keyword to which the Device blocks access. Click Delete to remove it.Apply Click this button to save your settings back to the Device.Cancel Click Cancel to restore your previously saved settings.
Chapter 17 Parental ControlVMG4380-B10A / VMG4325-B10A User’s Guide224
VMG4380-B10A / VMG4325-B10A User’s Guide 225CHAPTER 18Scheduler Rules18.1 OverviewYou can define time periods and days during which the Device performs scheduled rules of certain features (such as Firewall Access Control, Parental Control) on a specific user in the Scheduler Rulesscreen. 18.2 The Scheduler Rules ScreenUse this screen to view, add, or edit time schedule rules.Click Security > Scheduler Rules to open the following screen. Figure 112 Security > Scheduler Rules The following table describes the fields in this screen. Table 83 Security > Scheduler RulesLABEL DESCRIPTIONAdd new rule Click this to create a new rule.# This is the index number of the entry.Rule Name This shows the name of the rule.Day This shows the day(s) on which this rule is enabled.Time This shows the period of time on which this rule is enabled.Description This shows the description of this rule.Modify Click the Edit icon to edit the schedule.Click the Delete icon to delete a scheduler rule.Note: You cannot delete a scheduler rule once it is applied to a certain feature.
Chapter 18 Scheduler RulesVMG4380-B10A / VMG4325-B10A User’s Guide22618.2.1 Add/Edit a ScheduleClick the Add button in the Scheduler Rules screen or click the Edit icon next to a schedule ruleto open the following screen. Use this screen to configure a restricted access schedule for a specificuser on your network. Figure 113 Scheduler Rules: Add/Edit The following table describes the fields in this screen. Table 84 Scheduler Rules: Add/Edit LABEL DESCRIPTIONRule Name Enter a name (up to 31 printable English keyboard characters, not including spaces) for this schedule. Day Select check boxes for the days that you want the Device to perform this scheduler rule. Time if DayRangeEnter the time period of each day, in 24-hour format, during which parental control will beenforced.Description Enter a description for this scheduler rule.Apply Click Apply to save your changes.Cancel Click Cancel to exit this screen without saving.
VMG4380-B10A / VMG4325-B10A User’s Guide 227CHAPTER 19Certificates19.1 OverviewThe Device can use certificates (also called digital IDs) to authenticate users. Certificates are based on public-private key pairs. A certificate contains the certificate owner’s identity and public key.Certificates provide a way to exchange public keys for use in authentication. 19.1.1 What You Can Do in this Chapter• The Local Certificates screen lets you generate certification requests and import the Device'sCA-signed certificates (Section 19.4 on page 231).• The Trusted CA screen lets you save the certificates of trusted CAs to the Device (Section 19.4on page 231).19.2 What You Need to KnowThe following terms and concepts may help as you read through this chapter.Certification Authority A Certification Authority (CA) issues certificates and guarantees the identity of each certificate owner. There are commercial certification authorities like CyberTrust or VeriSign and government certification authorities. The certification authority uses its private key to sign certificates. Anyone can then use the certification authority's public key to verify the certificates. You can use the Device to generate certification requests that contain identifying information and public keys and then send the certification requests to a certification authority.
Chapter 19 CertificatesVMG4380-B10A / VMG4325-B10A User’s Guide22819.3 The Local Certificates ScreenClick Security > Certificates to open the Local Certificates screen. This is the Device’s summary list of certificates and certification requests. Figure 114 Security > Certificates > Local CertificatesThe following table describes the labels in this screen. Table 85 Security > Certificates > Local CertificatesLABEL DESCRIPTIONPrivate Key isprotected by apassword?Select the checkbox and enter the private key into the text box to store it on the Device. The private key should not exceed 63 ASCII characters (not including spaces).Browse... Click this to find the certificate file you want to upload. Import Certificate Click this button to save the certificate that you have enrolled from a certification authority from your computer to the Device.Create Certificate RequestClick this button to go to the screen where you can have the Device generate a certification request.Current File This field displays the name used to identify this certificate. It is recommended that yougive each certificate a unique name.Subject This field displays identifying information about the certificate’s owner, such as CN (Common Name), OU (Organizational Unit or department), O (Organization or company) and C (Country). It is recommended that each certificate have unique subject information. Issuer This field displays identifying information about the certificate’s issuing certification authority, such as a common name, organizational unit or department, organization or company and country.Valid From This field displays the date that the certificate becomes applicable. The text displays inred and includes a Not Yet Valid! message if the certificate has not yet becomeapplicable.Valid To This field displays the date that the certificate expires. The text displays in red and includes an Expiring! or Expired! message if the certificate is about to expire or has already expired.Modify Click the View icon to open a screen with an in-depth list of information about the certificate (or certification request).For a certification request, click Load Signed to import the signed certificate.Click the Remove icon to delete the certificate (or certification request). You cannotdelete a certificate that one or more features is configured to use.
Chapter 19 CertificatesVMG4380-B10A / VMG4325-B10A User’s Guide 22919.3.1 Create Certificate Request Click Security > Certificates > Local Certificates and then Create Certificate Request to open the following screen. Use this screen to have the Device generate a certification request.Figure 115 Create Certificate RequestThe following table describes the labels in this screen. After you click Apply, the following screen displays to notify you that you need to get the certificate request signed by a Certificate Authority. If you already have, click Load_Signed to import the signed certificate into the Device. Otherwise click Back to return to the Local Certificates screen. Table 86 Create Certificate RequestLABEL DESCRIPTIONCertificate NameType up to 63 ASCII characters (not including spaces) to identify this certificate.Common Name Select Auto to have the Device configure this field automatically. Or select Customize toenter it manually.Type the IP address (in dotted decimal notation), domain name or e-mail address in the field provided. The domain name or e-mail address can be up to 63 ASCII characters. The domain name or e-mail address is for identification purposes only and can be any string.Organization NameType up to 63 characters to identify the company or group to which the certificate owner belongs. You may use any character, including spaces, but the Device drops trailing spaces.State/ProvinceNameType up to 32 characters to identify the state or province where the certificate owner islocated. You may use any character, including spaces, but the Device drops trailing spaces.Country/RegionNameSelect a country to identify the nation where the certificate owner is located. Apply Click Apply to save your changes.Cancel Click Cancel to exit this screen without saving.
Chapter 19 CertificatesVMG4380-B10A / VMG4325-B10A User’s Guide230Figure 116 Certificate Request Created19.3.2 Load Signed Certificate After you create a certificate request and have it signed by a Certificate Authority, in the Local Certificates screen click the certificate request’s Load Signed icon to import the signed certificate into the Device. Note: You must remove any spaces from the certificate’s filename before you can importit.Figure 117 Load Signed Certificate
Chapter 19 CertificatesVMG4380-B10A / VMG4325-B10A User’s Guide 231The following table describes the labels in this screen. 19.4 The Trusted CA ScreenClick Security > Certificates > Trusted CA to open the following screen. This screen displays a summary list of certificates of the certification authorities that you have set the Device to accept as trusted. The Device accepts any valid certificate signed by a certification authority on this list as being trustworthy; thus you do not need to import any certificate that is signed by one of these certification authorities. Figure 118 Security > Certificates > Trusted CAThe following table describes the fields in this screen. Table 87 Load Signed CertificateLABEL DESCRIPTIONCertificate NameThis is the name of the signed certificate.Certificate Copy and paste the signed certificate into the text box to store it on the Device.Apply Click Apply to save your changes.Cancel Click Cancel to exit this screen without saving.Table 88 Security > Certificates > Trusted CALABEL DESCRIPTIONImportCertificateClick this button to open a screen where you can save the certificate of a certification authority that you trust to the Device.# This is the index number of the entry.Name This field displays the name used to identify this certificate.Subject This field displays information that identifies the owner of the certificate, such as Common Name (CN), OU (Organizational Unit or department), Organization (O), State (ST) and Country (C). It is recommended that each certificate have unique subject information.Type This field displays general information about the certificate. ca means that a Certification Authority signed the certificate.Modify Click the View icon to open a screen with an in-depth list of information about the certificate (or certification request).Click the Remove button to delete the certificate (or certification request). You cannotdelete a certificate that one or more features is configured to use.
Chapter 19 CertificatesVMG4380-B10A / VMG4325-B10A User’s Guide23219.4.1 View Trusted CA CertificateClick the View icon in the Trusted CA screen to open the following screen. Use this screen to view in-depth information about the certification authority’s certificate.Figure 119 Trusted CA: ViewThe following table describes the fields in this screen. Table 89 Trusted CA: ViewLABEL DESCRIPTIONName This field displays the identifying name of this certificate.Type This field displays general information about the certificate. ca means that a Certification Authority signed the certificate.Subject This field displays information that identifies the owner of the certificate, such as Common Name (CN), Organizational Unit (OU), Organization (O) and Country (C).Certificate This read-only text box displays the certificate in Privacy Enhanced Mail (PEM) format. PEM uses base 64 to convert the binary certificate into a printable form. You can copy and paste the certificate into an e-mail to send to friends or colleagues or you can copy and paste the certificate into a text editor and save the file on a management computer for later distribution (via floppy disk for example).Back Click Back to return to the previous screen.
Chapter 19 CertificatesVMG4380-B10A / VMG4325-B10A User’s Guide 23319.4.2 Import Trusted CA CertificateClick the Import Certificate button in the Trusted CA screen to open the following screen. The Device trusts any valid certificate signed by any of the imported trusted CA certificates.Figure 120 Trusted CA: Import Certificate The following table describes the fields in this screen. Table 90 Trusted CA: Import CertificateLABEL DESCRIPTIONCertificate FilePathType in the location of the certificate you want to upload in this field or click Browse ... tofind it. Enable TrustedCA for 802.1x AuthenticationIf you select this checkbox, the trusted CA will be used for 802.1x authentication. The selected trusted CA will be displayed in the Network Setting > Broadband > 802.1x: Edit screen.Certificate Copy and paste the certificate into the text box to store it on the Device.OK Click OK to save your changes.Cancel Click Cancel to exit this screen without saving.
Chapter 19 CertificatesVMG4380-B10A / VMG4325-B10A User’s Guide234
VMG4380-B10A / VMG4325-B10A User’s Guide 235CHAPTER 20Log20.1 OverviewThe web configurator allows you to choose which categories of events and/or alerts to have the Device log and then display the logs or have the Device send them to an administrator (as e-mail) or to a syslog server. 20.1.1 What You Can Do in this Chapter• Use the System Log screen to see the system logs (Section 20.2 on page 236).• Use the Security Log screen to see the security-related logs for the categories that you select (Section 20.3 on page 237).20.1.2 What You Need To KnowThe following terms and concepts may help as you read this chapter.Alerts and LogsAn alert is a type of log that warrants more serious attention. They include system errors, attacks (access control) and attempted access to blocked web sites. Some categories such as SystemErrors consist of both logs and alerts. You may differentiate them by their color in the View Log screen. Alerts display in red and logs display in black.Syslog Overview The syslog protocol allows devices to send event notification messages across an IP network to syslog servers that collect the event messages. A syslog-enabled device can generate a syslog message and send it to a syslog server.Syslog is defined in RFC 3164. The RFC defines the packet format, content and system log relatedinformation of syslog messages. Each syslog message has a facility and severity level. The syslog facility identifies a file in the syslog server. Refer to the documentation of your syslog program for details. The following table describes the syslog severity levels. Table 91 Syslog Severity LevelsCODE SEVERITY0 Emergency: The system is unusable.1 Alert: Action must be taken immediately.2 Critical: The system condition is critical.3 Error: There is an error condition on the system.4 Warning: There is a warning condition on the system.
Chapter 20 LogVMG4380-B10A / VMG4325-B10A User’s Guide23620.2 The System Log Screen Use the System Log screen to see the system logs. Click System Monitor > Log to open the System Log screen. Figure 121 System Monitor > Log > System LogThe following table describes the fields in this screen. 5 Notice: There is a normal but significant condition on the system.6 Informational: The syslog contains an informational message.7 Debug: The message is intended for debug-level purposes.Table 91 Syslog Severity LevelsCODE SEVERITYTable 92 System Monitor > Log > System LogLABEL DESCRIPTIONLevel Select a severity level from the drop-down list box. This filters search results according to the severity level you have selected. When you select a severity, the Device searchesthrough all logs of that severity or higher. Category Select the type of logs to display.Clear Log Click this to delete all the logs. Refresh Click this to renew the log screen. Export Log Click this to export the selected log(s).Email Log Now Click this to send the log file(s) to the E-mail address you specify in the Maintenance > Logs Setting screen.System Log# This field is a sequential value and is not associated with a specific entry.Time This field displays the time the log was recorded. Facility The log facility allows you to send logs to different files in the syslog server. Refer to the documentation of your syslog program for more details.Level This field displays the severity level of the logs that the device is to send to this syslog server.Messages This field states the reason for the log.
Chapter 20 LogVMG4380-B10A / VMG4325-B10A User’s Guide 23720.3 The Security Log ScreenUse the Security Log screen to see the security-related logs for the categories that you select. Click System Monitor > Log > Security Log to open the following screen. Figure 122 System Monitor > Log > Security LogThe following table describes the fields in this screen. Table 93 System Monitor > Log > Security LogLABEL DESCRIPTIONLevel Select a severity level from the drop-down list box. This filters search results according to the severity level you have selected. When you select a severity, the Device searchesthrough all logs of that severity or higher. Category Select the type of logs to display.Clear Log Click this to delete all the logs. Refresh Click this to renew the log screen. Export Log Click this to export the selected log(s).Email Log Now Click this to send the log file(s) to the E-mail address you specify in the Maintenance > Logs Setting screen.# This field is a sequential value and is not associated with a specific entry.Time This field displays the time the log was recorded. Facility The log facility allows you to send logs to different files in the syslog server. Refer to the documentation of your syslog program for more details.Level This field displays the severity level of the logs that the device is to send to this syslog server.Messages This field states the reason for the log.
Chapter 20 LogVMG4380-B10A / VMG4325-B10A User’s Guide238
VMG4380-B10A / VMG4325-B10A User’s Guide 239CHAPTER 21Traffic Status21.1 OverviewUse the Traffic Status screens to look at network traffic status and statistics of the WAN and LAN interfaces. 21.1.1 What You Can Do in this Chapter• Use the WAN screen to view the WAN traffic statistics (Section 21.2 on page 239).• Use the LAN screen to view the LAN traffic statistics (Section 21.3 on page 241).21.2 The WAN Status Screen Click System Monitor > Traffic Status to open the WAN screen. The figure in this screen shows the number of bytes received and sent on the Device.Figure 123 System Monitor > Traffic Status > WAN
Chapter 21 Traffic StatusVMG4380-B10A / VMG4325-B10A User’s Guide240The following table describes the fields in this screen. Table 94 System Monitor > Traffic Status > WANLABEL DESCRIPTIONConnectedInterface This shows the name of the WAN interface that is currently connected.Packets Sent Data This indicates the number of transmitted packets on this interface.Error This indicates the number of frames with errors transmitted on this interface.Drop This indicates the number of outgoing packets dropped on this interface.Packets ReceivedData This indicates the number of received packets on this interface.Error This indicates the number of frames with errors received on this interface.Drop This indicates the number of received packets dropped on this interface.more...hidemoreClick more... to show more information. Click hide more to hide them.DisabledInterfaceThis shows the name of the WAN interface that is currently disconnected.Packets Sent Data This indicates the number of transmitted packets on this interface.Error This indicates the number of frames with errors transmitted on this interface.Drop This indicates the number of outgoing packets dropped on this interface.Packets ReceivedData This indicates the number of received packets on this interface.Error This indicates the number of frames with errors received on this interface.Drop This indicates the number of received packets dropped on this interface.
Chapter 21 Traffic StatusVMG4380-B10A / VMG4325-B10A User’s Guide 24121.3 The LAN Status ScreenClick System Monitor > Traffic Status > LAN to open the following screen. The figure in this screen shows the interface that is currently connected on the Device.Figure 124 System Monitor > Traffic Status > LANThe following table describes the fields in this screen. Table 95 System Monitor > Traffic Status > LANLABEL DESCRIPTIONRefresh Interval Select how often you want the Device to update this screen.Interface This shows the LAN or WLAN interface. Bytes Sent This indicates the number of bytes transmitted on this interface.more...hidemoreClick more... to show more information. Click hide more to hide them.Interface This shows the LAN or WLAN interface. Sent (Packets)Data This indicates the number of transmitted packets on this interface.Error This indicates the number of frames with errors transmitted on this interface.Drop This indicates the number of outgoing packets dropped on this interface.Received (Packets)Data This indicates the number of received packets on this interface.Error This indicates the number of frames with errors received on this interface.Drop This indicates the number of received packets dropped on this interface.
Chapter 21 Traffic StatusVMG4380-B10A / VMG4325-B10A User’s Guide242
VMG4380-B10A / VMG4325-B10A User’s Guide 243CHAPTER 22ARP Table22.1 OverviewAddress Resolution Protocol (ARP) is a protocol for mapping an Internet Protocol address (IP address) to a physical machine address, also known as a Media Access Control or MAC address, on the local area network. An IP (version 4) address is 32 bits long. In an Ethernet LAN, MAC addresses are 48 bits long. TheARP Table maintains an association between each MAC address and its corresponding IP address.22.1.1 How ARP WorksWhen an incoming packet destined for a host device on a local area network arrives at the device, the device's ARP program looks in the ARP Table and, if it finds the address, sends it to the device.If no entry is found for the IP address, ARP broadcasts the request to all the devices on the LAN.The device fills in its own MAC and IP address in the sender address fields, and puts the known IP address of the target in the target IP address field. In addition, the device puts all ones in the target MAC field (FF.FF.FF.FF.FF.FF is the Ethernet broadcast address). The replying device (which is either the IP address of the device being sought or the router that knows the way) replaces the broadcast address with the target's MAC address, swaps the sender and target pairs, and unicasts the answer directly back to the requesting machine. ARP updates the ARP Table for future reference and then sends the packet to the MAC address that replied. 22.2 ARP Table ScreenUse the ARP table to view IP-to-MAC address mapping(s). To open this screen, click SystemMonitor > ARP Table.Figure 125 System Monitor > ARP TableThe following table describes the labels in this screen.Table 96 System Monitor > ARP TableLABEL DESCRIPTION# This is the ARP table entry number.IP Address This is the learned IP address of a device connected to a port.
Chapter 22 ARP TableVMG4380-B10A / VMG4325-B10A User’s Guide244MAC Address This is the MAC address of the device with the listed IP address.Device This is the type of interface used by the device. You can click on the device type to go to its configuration screen.Table 96 System Monitor > ARP Table (continued)LABEL DESCRIPTION
VMG4380-B10A / VMG4325-B10A User’s Guide 245CHAPTER 23Routing Table23.1 OverviewRouting is based on the destination address only and the Device takes the shortest path to forward a packet.23.2 The Routing Table ScreenClick System Monitor > Routing Table to open the following screen.Figure 126 System Monitor > Routing TableThe following table describes the labels in this screen.Table 97 System Monitor > Routing TableLABEL DESCRIPTIONDestination This indicates the destination IP address of this route.Gateway This indicates the IP address of the gateway that helps forward this route’s traffic.Subnet Mask This indicates the destination subnet mask of this route.Flag This indicates the route status.U-Up: The route is up.!-Reject: The route is blocked and will force a route lookup to fail.G-Gateway: The route uses a gateway to forward traffic. H-Host: The target of the route is a host.R-Reinstate: The route is reinstated for dynamic routing.D-Dynamic (redirect): The route is dynamically installed by a routing daemon or redirect.M-Modified (redirect): The route is modified from a routing daemon or redirect.Metric The metric represents the "cost of transmission". A router determines the best route for transmission by choosing a path with the lowest "cost". The smaller the number, the lower the "cost".
Chapter 23 Routing TableVMG4380-B10A / VMG4325-B10A User’s Guide246Service This indicates the name of the service used to forward the route.Interface This indicates the name of the interface through which the route is forwarded.br0 indicates the LAN interface.ptm0 indicates the WAN interface using IPoE or in bridge mode.ppp0 indicates the WAN interface using PPPoE.Table 97 System Monitor > Routing Table (continued)LABEL DESCRIPTION
VMG4380-B10A / VMG4325-B10A User’s Guide 247CHAPTER 24IGMP Status24.1 OverviewUse the IGMP Status screens to look at IGMP group status and traffic statistics. 24.2 The IGMP Group Status ScreenUse this screen to look at the current list of multicast groups the Device has joined and which ports have joined it. To open this screen, click System Monitor > IGMP Group Status.Figure 127 System Monitor > IGMP Group StatusThe following table describes the labels in this screen.Table 98 System Monitor > IGMP Group StatusLABEL DESCRIPTIONInterface This field displays the name of an interface on the Device that belongs to an IGMP multicastgroup.Multicast Group This field displays the name of the IGMP multicast group to which the interface belongs.Filter Mode INCLUDE means that only the IP addresses in the Source List get to receive the multicastgroup’s traffic.EXCLUDE means that the IP addresses in the Source List are not allowed to receive the multicast group’s traffic but other IP addresses can.Source List This is the list of IP addresses that are allowed or not allowed to receive the multicastgroup’s traffic depending on the filter mode.
Chapter 24 IGMP StatusVMG4380-B10A / VMG4325-B10A User’s Guide248
VMG4380-B10A / VMG4325-B10A User’s Guide 249CHAPTER 25xDSL Statistics25.1 The xDSL Statistics ScreenUse this screen to view detailed DSL statistics. Click System Monitor > xDSL Statistics to open the following screen.Figure 128 System Monitor > xDSL Statistics
Chapter 25 xDSL StatisticsVMG4380-B10A / VMG4325-B10A User’s Guide250The following table describes the labels in this screen. Table 99 Status > xDSL StatisticsLABEL DESCRIPTIONRefresh Interval Select the time interval for refreshing statistics.Line Select which DSL line’s statistics you want to display.xDSL Training StatusThis displays the current state of setting up the DSL connection.Mode This displays the ITU standard used for this connection.Traffic Type This displays the type of traffic the DSL port is sending and receiving. Inactive displays ifthe DSL port is not currently sending or receiving traffic.Link Uptime This displays how long the port has been running (or connected) since the last time it wasstarted.xDSL Port DetailsUpstream These are the statistics for the traffic direction going out from the port to the service provider.Downstream These are the statistics for the traffic direction coming into the port from the service provider. Line Rate These are the data transfer rates at which the port is sending and receiving data.Actual Net Data RateThese are the rates at which the port is sending and receiving the payload data without transport layer protocol headers and traffic.Trellis Coding This displays whether or not the port is using Trellis coding for traffic it is sending and receiving. Trellis coding helps to reduce the noise in ADSL transmissions. Trellis may reducethroughput but it makes the connection more stable.SNR Margin This is the upstream and downstream Signal-to-Noise Ratio margin (in dB). A DMT sub-carrier’s SNR is the ratio between the received signal power and the received noise power.The signal-to-noise ratio margin is the maximum that the received noise power could increase with the system still being able to meet its transmission targets.Actual Delay This is the upstream and downstream interleave delay. It is the wait (in milliseconds) that determines the size of a single block of data to be interleaved (assembled) and thentransmitted. Interleave delay is used when transmission error correction (Reed- Solomon) is necessary due to a less than ideal telephone line. The bigger the delay, the bigger the data block size, allowing better error correction to be performed. Transmit Power This is the upstream and downstream far end actual aggregate transmit power (in dBm).Upstream is how much power the port is using to transmit to the service provider. Downstream is how much port the service provider is using to transmit to the port.Receive Power Upstream is how much power the service provider is receiving from the port. Downstreamis how much power the port is receiving from the service provider.Actual INP Sudden spikes in the line’s level of external noise (impulse noise) can cause errors and result in lost packets. This could especially impact the quality of multimedia traffic such asvoice or video. Impulse noise protection (INP) provides a buffer to allow for correction oferrors caused by error correction to deal with this. The number of DMT (Discrete Multi-Tone) symbols shows the level of impulse noise protection for the upstream and downstream traffic. A higher symbol value provides higher error correction capability, but it causes overhead and higher delay which may increase error rates in received multimedia data.Total Attenuation This is the upstream and downstream line attenuation, measured in decibels (dB). This attenuation is the difference between the power transmitted at the near-end and the power received at the far-end. Attenuation is affected by the channel characteristics (wire gauge,quality, condition and length of the physical line).Attainable Net Data RateThese are the highest theoretically possible transfer rates at which the port could send and receive payload data without transport layer protocol headers and traffic.xDSL Counters
Chapter 25 xDSL StatisticsVMG4380-B10A / VMG4325-B10A User’s Guide 251Downstream These are the statistics for the traffic direction coming into the port from the service provider. Upstream These are the statistics for the traffic direction going out from the port to the service provider.FEC This is the number of Far End Corrected blocks.CRC This is the number of Cyclic Redundancy Checks. ES This is the number of Errored Seconds meaning the number of seconds containing at leastone errored block or at least one defect.SES This is the number of Severely Errored Seconds meaning the number of seconds containing 30% or more errored blocks or at least one defect. This is a subset of ES.UAS This is the number of UnAvailable Seconds.LOS This is the number of Loss Of Signal seconds.LOF This is the number of Loss Of Frame seconds.LOM This is the number of Loss of Margin seconds.Table 99 Status > xDSL Statistics (continued)LABEL DESCRIPTION
Chapter 25 xDSL StatisticsVMG4380-B10A / VMG4325-B10A User’s Guide252
VMG4380-B10A / VMG4325-B10A User’s Guide 253CHAPTER 26User Account26.1 Overview In the Users Account screen, you can change the password of the user account that you used to log in the Device. 26.2 The User Account ScreenClick Maintenance > User Account to open the following screen.Figure 129 Maintenance > User AccountThe following table describes the labels in this screen. Table 100 Maintenance > User AccountLABEL DESCRIPTIONUser Name This field displays the name of the account that you used to log in the system. Old Password Type the default password or the existing password you use to access the system in thisfield.New Password Type your new system password (up to 30 characters). Note that as you type a password, the screen displays a (*) for each character you type. After you change the password, use the new password to access the Device.Retype toconfirmType the new password again for confirmation.Apply Click Apply to save your changes.Cancel Click Cancel to restore your previously saved settings.
Chapter 26 User AccountVMG4380-B10A / VMG4325-B10A User’s Guide254
VMG4380-B10A / VMG4325-B10A User’s Guide 255CHAPTER 27Remote Management27.1 OverviewRemote Management allows you to manage your Device from a remote location through the following interfaces:• LAN• WAN• Trust DomainNote: The Device is managed using the Web Configurator.27.2 The Remote MGMT ScreenUse this screen to configure through which interface(s) users can use which service(s) to manage the Device.Click Maintenance > Remote MGMT to open the following screen. Figure 130 Maintenance > Remote MGMT
Chapter 27 Remote ManagementVMG4380-B10A / VMG4325-B10A User’s Guide256The following table describes the fields in this screen. Table 101 Maintenance > Remote MGMT LABEL DESCRIPTIONTrust DomainStatus This field displays whether the Trust Domain is active or not.IP Address Enter the Trust Domain IP address.Services This is the service you may use to access the Device.LAN/WLAN Select the Enable check box for the corresponding services that you want to allow access to the Device from the LAN/WLAN.WAN Select the Enable check box for the corresponding services that you want to allow access to the Device from the WAN.Trust Domain Select the Enable check box for the corresponding services that you want to allow access to the Device from the Trust Domain.Port You may change the server port number for a service if needed, however you must use the same port number in order to use that service for remote management.CertificateHTTPSCertificateSelect a certificate the HTTPS server (the Device) uses to authenticate itself to the HTTPS client. You must have certificates already configured in the Certificates screen.Apply Click Apply to save your changes back to the Device.Cancel Click Cancel to restore your previously saved settings.
VMG4380-B10A / VMG4325-B10A User’s Guide 257CHAPTER 28TR-069 Client28.1 OverviewThis chapter explains how to configure the Device’s TR-069 auto-configuration settings.28.2 The TR-069 Client ScreenTR-069 defines how Customer Premise Equipment (CPE), for example your Device, can be managed over the WAN by an Auto Configuration Server (ACS). TR-069 is based on sending Remote Procedure Calls (RPCs) between an ACS and a client device. RPCs are sent in Extensible Markup Language (XML) format over HTTP or HTTPS.An administrator can use an ACS to remotely set up the Device, modify settings, perform firmware upgrades as well as monitor and diagnose the Device. You have to enable the device to be managed by the ACS and specify the ACS IP address or domain name and username and password.Click Maintenance > TR-069 Client to open the following screen. Use this screen to configure your Device to be managed by an ACS.Figure 131 Maintenance > TR-069 Client
Chapter 28 TR-069 ClientVMG4380-B10A / VMG4325-B10A User’s Guide258The following table describes the fields in this screen. Table 102 Maintenance > TR-069 ClientLABEL DESCRIPTIONInform Select Enable for the Device to send periodic inform via TR-069 on the WAN. Otherwise, select Disable.Inform Interval Enter the time interval (in seconds) at which the Device sends information to the auto-configuration server.ACS URL Enter the URL or IP address of the auto-configuration server.ACS User Name Enter the TR-069 user name for authentication with the auto-configuration server.ACS Password Enter the TR-069 password for authentication with the auto-configuration server.WAN Interface used by TR-069 clientSelect a WAN interface through which the TR-069 traffic passes.If you select Any_WAN, you should also select the pre-configured WAN connection(s).Display SOAP messages onserial consoleSelect Enable to show the SOAP messages on the console.ConnectionRequestAuthenticationSelect this option to enable authentication when there is a connection request from the ACS.ConnectionRequest User NameEnter the connection request user name.When the ACS makes a connection request to the Device, this user name is used toauthenticate the ACS.ConnectionRequestPasswordEnter the connection request password.When the ACS makes a connection request to the Device, this password is used to authenticate the ACS.ConnectionRequest URLThis shows the connection request URL.The ACS can use this URL to make a connection request to the Device.Local certificateused by TR-069 clientYou can choose a local certificate used by TR-069 client. The local certificate should be imported in the Security > Certificates > Local Certificates screen.Apply Click Apply to save your changes.Cancel Click Cancel to exit this screen without saving.
VMG4380-B10A / VMG4325-B10A User’s Guide 259CHAPTER 29TR-06429.1 OverviewThis chapter explains how to configure the Device’s TR-064 auto-configuration settings.29.2 The TR-064 ScreenTR-064 is a LAN-Side DSL CPE Configuration protocol defined by the DSL Forum. TR-064 is built on top of UPnP. It allows the users to use a TR-064 compliant CPE management application on their computers from the LAN to discover the CPE and configure user-specific parameters, such as the username and password.Click Maintenance > TR-064 to open the following screen. Figure 132 Maintenance > TR-064 The following table describes the fields in this screen. Table 103 Maintenance > TR-064LABEL DESCRIPTIONState Select Enable to activate management via TR-064 on the LAN.Apply Click Apply to save your changes.Cancel Click Cancel to exit this screen without saving.
Chapter 29 TR-064VMG4380-B10A / VMG4325-B10A User’s Guide260
VMG4380-B10A / VMG4325-B10A User’s Guide 261CHAPTER 30Time Settings30.1 OverviewThis chapter shows you how to configure system related settings, such as system time, password, name, the domain name and the inactivity timeout interval. 30.2 The Time Screen To change your Device’s time and date, click Maintenance > Time. The screen appears as shown. Use this screen to configure the Device’s time based on your local time zone.Figure 133 Maintenance > Time Setting
Chapter 30 Time SettingsVMG4380-B10A / VMG4325-B10A User’s Guide262The following table describes the fields in this screen. Table 104 Maintenance > Time SettingLABEL DESCRIPTIONCurrent Date/TimeCurrent Time This field displays the time of your Device.Each time you reload this page, the Device synchronizes the time with the time server.Current Date This field displays the date of your Device. Each time you reload this page, the Device synchronizes the date with the time server.NTP Time ServerFirst ~ Fifth NTPtime server Select an NTP time server from the drop-down list box. Otherwise, select Other and enter the IP address or URL (up to 29 extended ASCII characters in length) of your time server. Select None if you don’t want to configure the time server.Check with your ISP/network administrator if you are unsure of this information.Time ZoneTime zone offset Choose the time zone of your location. This will set the time difference between your timezone and Greenwich Mean Time (GMT).Daylight Saving Daylight Saving Time is a period from late spring to early fall when many countries set their clocks ahead of normal local time by one hour to give more daytime light in the evening.State Select Enable if you use Daylight Saving Time.Start rule: Configure the day and time when Daylight Saving Time starts if you enabled DaylightSaving. You can select a specific date in a particular month or a specific day of a specificweek in a particular month. The Time field uses the 24 hour format. Here are a couple ofexamples:Daylight Saving Time starts in most parts of the United States on the second Sunday ofMarch. Each time zone in the United States starts using Daylight Saving Time at 2 A.M. local time. So in the United States, set the day to Second, Sunday, the month to Marchand the time to 2 in the Hour field.Daylight Saving Time starts in the European Union on the last Sunday of March. All of the time zones in the European Union start using Daylight Saving Time at the same moment(1 A.M. GMT or UTC). So in the European Union you would set the day to Last, Sundayand the month to March. The time you select in the o'clock field depends on your time zone. In Germany for instance, you would select 2 in the Hour field because Germany's time zone is one hour ahead of GMT or UTC (GMT+1). End rule Configure the day and time when Daylight Saving Time ends if you enabled Daylight Saving. You can select a specific date in a particular month or a specific day of a specificweek in a particular month. The Time field uses the 24 hour format. Here are a couple of examples:Daylight Saving Time ends in the United States on the first Sunday of November. Eachtime zone in the United States stops using Daylight Saving Time at 2 A.M. local time. Soin the United States you would set the day to First, Sunday, the month to November and the time to 2 in the Hour field. Daylight Saving Time ends in the European Union on the last Sunday of October. All of thetime zones in the European Union stop using Daylight Saving Time at the same moment (1 A.M. GMT or UTC). So in the European Union you would set the day to Last, Sunday, and the month to October. The time you select in the o'clock field depends on your time zone. In Germany for instance, you would select 2 in the Hour field because Germany's time zone is one hour ahead of GMT or UTC (GMT+1).
Chapter 30 Time SettingsVMG4380-B10A / VMG4325-B10A User’s Guide 263Apply Click Apply to save your changes.Cancel Click Cancel to exit this screen without saving.Table 104 Maintenance > Time Setting (continued)LABEL DESCRIPTION
Chapter 30 Time SettingsVMG4380-B10A / VMG4325-B10A User’s Guide264
VMG4380-B10A / VMG4325-B10A User’s Guide 265CHAPTER 31E-mail Notification31.1 Overview A mail server is an application or a computer that runs such an application to receive, forward and deliver e-mail messages.To have the Device send reports, logs or notifications via e-mail, you must specify an e-mail serverand the e-mail addresses of the sender and receiver.31.2 The Email Notification ScreenClick Maintenance > Email Notification to open the Email Notification screen. Use this screen to view, remove and add mail server information on the Device.Figure 134 Maintenance > Email NotificationThe following table describes the labels in this screen. Table 105 Maintenance > Email NotificationLABEL DESCRIPTIONAdd New Email Click this button to create a new entry.Mail Server AddressThis field displays the server name or the IP address of the mail server.Username This field displays the user name of the sender’s mail account.Password This field displays the password of the sender’s mail account.Email Address This field displays the e-mail address that you want to be in the from/sender line of the e-mail that the Device sends.Remove Click this button to delete the selected entry(ies).
Chapter 31 E-mail NotificationVMG4380-B10A / VMG4325-B10A User’s Guide26631.2.1 Email Notification Edit Click the Add button in the Email Notification screen. Use this screen to configure the requiredinformation for sending e-mail via a mail server. Figure 135 Email Notification > Add The following table describes the labels in this screen. Table 106 Email Notification > AddLABEL DESCRIPTIONMail Server AddressEnter the server name or the IP address of the mail server for the e-mail address specified in the Account Email Address field. If this field is left blank, reports, logs or notifications will not be sent via e-mail.AuthenticationUsernameEnter the user name (up to 32 characters). This is usually the user name of a mail accountyou specified in the Account Email Address field.AuthenticationPasswordEnter the password associated with the user name above.Account Email AddressEnter the e-mail address that you want to be in the from/sender line of the e-mailnotification that the Device sends.If you activate SSL/TLS authentication, the e-mail address must be able to be authenticated by the mail server as well.Apply Click this button to save your changes and return to the previous screen.Cancel Click this button to begin configuring this screen afresh.
VMG4380-B10A / VMG4325-B10A User’s Guide 267CHAPTER 32Logs Setting32.1 Overview You can configure where the Device sends logs and which logs and/or immediate alerts the Device records in the Logs Setting screen.32.2 The Log Settings ScreenTo change your Device’s log settings, click Maintenance > Logs Setting. The screen appears as shown.Figure 136 Maintenance > Logs Setting
Chapter 32 Logs SettingVMG4380-B10A / VMG4325-B10A User’s Guide268The following table describes the fields in this screen. 32.2.1 Example E-mail LogAn "End of Log" message displays for each mail in which a complete log has been sent. Thefollowing is an example of a log sent by e-mail.• You may edit the subject title.• The date format here is Day-Month-Year.• The date format here is Month-Day-Year. The time format is Hour-Minute-Second.Table 107 Maintenance > Logs SettingLABEL DESCRIPTIONSyslog SettingSyslog Logging The Device sends a log to an external syslog server. Select Enable to enable syslog logging.Mode Select the syslog destination from the drop-down list box. If you select Remote, the log(s) will be sent to a remote syslog server. If you select LocalFile, the log(s) will be saved in a local file. If you want to send the log(s) to a remote syslog server and save it in a local file, select Local File and Remote.Syslog Server Enter the server name or IP address of the syslog server that will log the selected categoriesof logs. UDP Port Enter the port number used by the syslog server.E-mail Log SettingsMail Server Enter the server name or the IP address of the mail server for the e-mail addressesspecified below. If this field is left blank, logs and alert messages will not be sent via E-mail. System LogMail SubjectType a title that you want to be in the subject line of the system log e-mail message thatthe Device sends.Security Log Mail SubjectType a title that you want to be in the subject line of the security log e-mail message thatthe Device sends.Send Log to The Device sends logs to the e-mail address specified in this field. If this field is left blank, the Device does not send logs via E-mail. Send Alarm to Alerts are real-time notifications that are sent as soon as an event, such as a DoS attack, system error, or forbidden web access attempt occurs. Enter the E-mail address where the alert messages will be sent. Alerts include system errors, attacks and attempted access to blocked web sites. If this field is left blank, alert messages will not be sent via E-mail. Alarm Interval Specify how often the alarm should be updated.AllowedCapacity BeforeEmail Set what percent of the Device’s log storage space can be filled before the Device sends a log e-mail. Clear log aftersending mailSelect this to delete all the logs after the Device sends an E-mail of the logs.Active Log and AlertSystem Log Select the categories of system logs that you want to record.Security Log Select the categories of security logs that you want to record.Sendimmediate alertSelect log categories for which you want the Device to send E-mail alerts immediately.Apply Click Apply to save your changes.Cancel Click Cancel to restore your previously saved settings.
Chapter 32 Logs SettingVMG4380-B10A / VMG4325-B10A User’s Guide 269• "End of Log" message shows that a complete log has been sent.Figure 137 E-mail Log ExampleSubject: Firewall Alert FromDate: Fri, 07 Apr 2000 10:05:42 From: user@zyxel.com To: user@zyxel.com 1|Apr 7 00 |From:192.168.1.1 To:192.168.1.255 |default policy |forward | 09:54:03 |UDP src port:00520 dest port:00520 |<1,00> | 2|Apr 7 00 |From:192.168.1.131 To:192.168.1.255 |default policy |forward| 09:54:17 |UDP src port:00520 dest port:00520 |<1,00> | 3|Apr 7 00 |From:192.168.1.6 To:10.10.10.10 |match |forward | 09:54:19 |UDP src port:03516 dest port:00053 |<1,01> | ……………………………..{snip}…………………………………..……………………………..{snip}…………………………………..126|Apr 7 00 |From:192.168.1.1 To:192.168.1.255 |match |forward| 10:05:00 |UDP src port:00520 dest port:00520 |<1,02> | 127|Apr 7 00 |From:192.168.1.131 To:192.168.1.255 |match |forward | 10:05:17 |UDP src port:00520 dest port:00520 |<1,02> | 128|Apr 7 00 |From:192.168.1.1 To:192.168.1.255 |match |forward | 10:05:30 |UDP src port:00520 dest port:00520 |<1,02> | End of Firewall Log
Chapter 32 Logs SettingVMG4380-B10A / VMG4325-B10A User’s Guide270
VMG4380-B10A / VMG4325-B10A User’s Guide 271CHAPTER 33Firmware Upgrade33.1 OverviewThis chapter explains how to upload new firmware to your Device. You can download new firmware releases from your nearest ZyXEL FTP site (or www.zyxel.com) to use to upgrade your device’sperformance.Only use firmware for your device’s specific model. Refer to the label onthe bottom of your Device.33.2 The Firmware ScreenClick Maintenance > Firmware Upgrade to open the following screen. The upload process uses HTTP (Hypertext Transfer Protocol) and may take up to two minutes. After a successful upload, thesystem will reboot. Do NOT turn off the Device while firmware upload is in progress!Figure 138 Maintenance > Firmware UpgradeThe following table describes the labels in this screen. Table 108 Maintenance > Firmware UpgradeLABEL DESCRIPTIONCurrent Firmware VersionThis is the present Firmware version and the date created. File Path Type in the location of the file you want to upload in this field or click Browse ... to find it.Browse... Click this to find the .bin file you want to upload. Remember that you must decompress compressed (.zip) files before you can upload them. Upload Click this to begin the upload process. This process may take up to two minutes.
Chapter 33 Firmware UpgradeVMG4380-B10A / VMG4325-B10A User’s Guide272After you see the firmware updating screen, wait two minutes before logging into the Device again. Figure 139 Firmware UploadingThe Device automatically restarts in this time causing a temporary network disconnect. In someoperating systems, you may see the following icon on your desktop.Figure 140 Network Temporarily DisconnectedAfter two minutes, log in again and check your new firmware version in the Status screen.If the upload was not successful, the following screen will appear. Click OK to go back to the Firmware Upgrade screen.Figure 141 Error Message
VMG4380-B10A / VMG4325-B10A User’s Guide 273CHAPTER 34Configuration34.1 OverviewThe Configuration screen allows you to backup and restore device configurations. You can also reset your device settings back to the factory default.34.2 The Configuration Screen Click Maintenance > Configuration. Information related to factory defaults, backup configuration, and restoring configuration appears in this screen, as shown next.Figure 142 Maintenance > ConfigurationBackup Configuration Backup Configuration allows you to back up (save) the Device’s current configuration to a file on your computer. Once your Device is configured and functioning properly, it is highly recommended that you back up your configuration file before making configuration changes. The backup configuration file will be useful in case you need to return to your previous settings. Click Backup to save the Device’s current configuration to your computer.
Chapter 34 ConfigurationVMG4380-B10A / VMG4325-B10A User’s Guide274Restore Configuration Restore Configuration allows you to upload a new or previously saved configuration file from your computer to your Device.Do not turn off the Device while configuration file upload is in progress.After the Device configuration has been restored successfully, the login screen appears. Login again to restart the Device. The Device automatically restarts in this time causing a temporary network disconnect. In someoperating systems, you may see the following icon on your desktop.Figure 143 Network Temporarily DisconnectedIf you uploaded the default configuration file you may need to change the IP address of your computer to be in the same subnet as that of the default device IP address (192.168.1.1). See Appendix A on page 287 for details on how to set up your computer’s IP address.If the upload was not successful, the following screen will appear. Click OK to go back to the Configuration screen.Figure 144 Configuration Upload ErrorTable 109 Restore ConfigurationLABEL DESCRIPTIONFile Path Type in the location of the file you want to upload in this field or click Browse ... to find it.Browse... Click this to find the file you want to upload. Remember that you must decompress compressed (.ZIP) files before you can upload them. Upload Click this to begin the upload process.
Chapter 34 ConfigurationVMG4380-B10A / VMG4325-B10A User’s Guide 275Reset to Factory Defaults Click the Reset button to clear all user-entered configuration information and return the Device toits factory defaults. The following warning screen appears.Figure 145 Reset Warning MessageFigure 146 Reset In Process MessageYou can also press the RESET button on the rear panel to reset the factory defaults of your Device. Refer to Section on page 22 for more information on the RESET button.34.3 The Reboot Screen System restart allows you to reboot the Device remotely without turning the power off. You may need to do this if the Device hangs, for example.Click Maintenance > Reboot. Click Reboot to have the Device reboot. This does not affect the Device's configuration. Figure 147 Maintenance > Reboot
VMG4380-B10A / VMG4325-B10A User’s Guide 276CHAPTER 35Diagnostic35.1 OverviewThe Diagnostic screens display information to help you identify problems with the Device.The route between a CO VDSL switch and one of its CPE may go through switches owned by independent organizations. A connectivity fault point generally takes time to discover and impacts subscriber’s network access. In order to eliminate the management and maintenance efforts, IEEE 802.1ag is a Connectivity Fault Management (CFM) specification which allows network administrators to identify and manage connection faults. Through discovery and verification of the path, CFM can detect, analyze and isolate connectivity faults in bridged LANs.35.1.1 What You Can Do in this Chapter• The Ping & TraceRoute & NsLookup screen lets you ping an IP address or trace the route packets take to a host (Section 35.3 on page 277).• The 802.1ag screen lets you perform CFM actions (Section 35.5 on page 279).• The OAM Ping Test screen lets you send an ATM OAM (Operation, Administration and Maintenance) packet to verify the connectivity of a specific PVC. (Section 35.5 on page 279).35.2 What You Need to KnowThe following terms and concepts may help as you read through this chapter.How CFM Works A Maintenance Association (MA) defines a VLAN and associated Maintenance End Point (MEP) ports on the device under a Maintenance Domain (MD) level. An MEP port has the ability to send Connectivity Check Messages (CCMs) and get other MEP ports information from neighbor devices’ CCMs within an MA.CFM provides two tests to discover connectivity faults. • Loopback test - checks if the MEP port receives its Loop Back Response (LBR) from its target after it sends the Loop Back Message (LBM). If no response is received, there might be a connectivity fault between them. • Link trace test - provides additional connectivity fault analysis to get more information on where the fault is. If an MEP port does not respond to the source MEP, this may indicate a fault. Administrators can take further action to check and resume services from the fault according to the line connectivity status report.
Chapter 35 DiagnosticVMG4380-B10A / VMG4325-B10A User’s Guide 27735.3 Ping & TraceRoute & NsLookup Use this screen to ping, traceroute, or nslookup an IP address. Click Maintenance > Diagnostic > Ping & TraceRoute & NsLookup to open the screen shown next.Figure 148 Maintenance > Diagnostic > Ping & TraceRoute & NsLookup The following table describes the fields in this screen. Table 110 Maintenance > Diagnostic > Ping & TraceRoute & NsLookupLABEL DESCRIPTIONURL or IPAddressType the IP address of a computer that you want to perform ping, traceroute, or nslookup inorder to test a connection.Ping Click this to ping the IP address that you entered.TraceRoute Click this button to perform the traceroute function. This determines the path a packettakes to the specified computer.Nslookup Click this button to perform a DNS lookup on the IP address of a computer you enter.
Chapter 35 DiagnosticVMG4380-B10A / VMG4325-B10A User’s Guide27835.4 802.1agClick Maintenance > Diagnostic > 8.2.1ag to open the following screen. Use this screen to perform CFM actions. Figure 149 Maintenance > Diagnostic > 802.1ag The following table describes the fields in this screen. Table 111 Maintenance > Diagnostic > 802.1agLABEL DESCRIPTION802.1ag Connectivity Fault ManagementMaintenanceDomain (MD)LevelSelect a level (0-7) under which you want to create an MA.Destination MAC AddressEnter the target device’s MAC address to which the Device performs a CFM loopback test.802.1Q VLAN IDType a VLAN ID (0-4095) for this MA.VDSL TrafficTypeThis shows whether the VDSL traffic is activated.Loopback Message (LBM)This shows how many Loop Back Messages (LBMs) are sent and if there is any inorder or outorder Loop Back Response (LBR) received from a remote MEP.LinktraceMessage (LTM)This shows the destination MAC address in the Link Trace Response (LTR).Set MD Level Click this button to configure the MD (Maintenance Domain) level.Send Loopback Click this button to have the selected MEP send the LBM (Loop Back Message) to a specified remote end point.Send Linktrace Click this button to have the selected MEP send the LTMs (Link Trace Messages) to a specified remote end point.
Chapter 35 DiagnosticVMG4380-B10A / VMG4325-B10A User’s Guide 27935.5 OAM Ping TestClick Maintenance > Diagnostic > OAM Ping Test to open the screen shown next. Use this screen to perform an OAM (Operation, Administration and Maintenance) F4 or F5 loopback test on a PVC. The Device sends an OAM F4 or F5 packet to the DSLAM or ATM switch and then returns it to the Device. The test result then displays in the text box. ATM sets up virtual circuits over which end systems communicate. The terminology for virtual circuits is as follows:Figure 150 Virtual Circuit TopologyThink of a virtual path as a cable that contains a bundle of wires. The cable connects two points and wires within the cable provide individual circuits between the two points. In an ATM cell header, a VPI (Virtual Path Identifier) identifies a link formed by a virtual path; a VCI (Virtual Channel Identifier) identifies a channel within a virtual path. A series of virtual paths make up a virtual circuit.F4 cells operate at the virtual path (VP) level, while F5 cells operate at the virtual channel (VC) level. F4 cells use the same VPI as the user data cells on VP connections, but use different predefined VCI values. F5 cells use the same VPI and VCI as the user data cells on the VCconnections, and are distinguished from data cells by a predefinded Payload Type Identifier (PTI) in the cell header. Both F4 flows and F5 flows are bidirectional and have two types. • segment F4 flows (VCI=3)• end-to-end F4 flows (VCI=4)• segment F5 flows (PTI=100)• end-to-end F5 flows (PTI=101)OAM F4 or F5 tests are used to check virtual path or virtual channel availability between two DSL devices. Segment flows are terminated at the connecting point which terminates a VP or VC segment. End-to-end flows are terminated at the end point of a VP or VC connection, where an ATM link is terminated. Segment loopback tests allow you to verify integrity of a PVC to the nearest neighboring ATM device. End-to-end loopback tests allow you to verify integrity of an end-to-end PVC.Note: The DSLAM to which the Device is connected must also support ATM F4 and/or F5to use this test.• Virtual Channel (VC) Logical connections between ATM devices• Virtual Path (VP) A bundle of virtual channels• Virtual Circuits A series of virtual paths between circuit end points
Chapter 35 DiagnosticVMG4380-B10A / VMG4325-B10A User’s Guide280Note: This screen is available only when you configure an ATM layer-2 interface.Figure 151 Maintenance > Diagnostic > OAM Ping TestThe following table describes the fields in this screen. Table 112 Maintenance > Diagnostic > OAM Ping TestLABEL DESCRIPTIONSelect a PVC on which you want to perform the loopback test.F4 segment Press this to perform an OAM F4 segment loopback test.F4 end-end Press this to perform an OAM F4 end-to-end loopback test.F5 segment Press this to perform an OAM F5 segment loopback test.F5 end-end Press this to perform an OAM F5 end-to-end loopback test.
VMG4380-B10A / VMG4325-B10A User’s Guide 281CHAPTER 36TroubleshootingThis chapter offers some suggestions to solve problems you might encounter. The potential problems are divided into the following categories. •Power, Hardware Connections, and LEDs•Device Access and Login•Internet Access•Wireless Internet Access•USB Device Connection•UPnP36.1 Power, Hardware Connections, and LEDsThe Device does not turn on. None of the LEDs turn on.1Make sure the Device is turned on. 2Make sure you are using the power adaptor or cord included with the Device.3Make sure the power adaptor or cord is connected to the Device and plugged in to an appropriate power source. Make sure the power source is turned on.4Turn the Device off and on.5If the problem continues, contact the vendor.One of the LEDs does not behave as expected.1Make sure you understand the normal behavior of the LED. See Section 1.5 on page 21.2Check the hardware connections.3Inspect your cables for damage. Contact the vendor to replace any damaged cables.4Turn the Device off and on.
Chapter 36 TroubleshootingVMG4380-B10A / VMG4325-B10A User’s Guide2825If the problem continues, contact the vendor.36.2 Device Access and LoginI forgot the IP address for the Device.1The default LAN IP address is 192.168.1.1.2If you changed the IP address and have forgotten it, you might get the IP address of the Device by looking up the IP address of the default gateway for your computer. To do this in most Windows computers, click Start > Run, enter cmd, and then enter ipconfig. The IP address of the Default Gateway might be the IP address of the Device (it depends on the network), so enter this IP address in your Internet browser.3If this does not work, you have to reset the device to its factory defaults. See Section on page 22.I forgot the password.1The default admin password is 1234.2If this does not work, you have to reset the device to its factory defaults. See Section on page 22.I cannot see or access the Login screen in the web configurator.1Make sure you are using the correct IP address.• The default IP address is 192.168.1.1.• If you changed the IP address (Section 8.2 on page 133), use the new IP address.• If you changed the IP address and have forgotten it, see the troubleshooting suggestions for I forgot the IP address for the Device.2Check the hardware connections, and make sure the LEDs are behaving as expected. See Section 1.5 on page 21.3Make sure your Internet browser does not block pop-up windows and has JavaScripts and Javaenabled. See Appendix C on page 317.4If it is possible to log in from another interface, check the service control settings for HTTP and HTTPS (Maintenance > Remote MGMT).5Reset the device to its factory defaults, and try to access the Device with the default IP address. See Section on page 22.
Chapter 36 TroubleshootingVMG4380-B10A / VMG4325-B10A User’s Guide 2836If the problem continues, contact the network administrator or vendor, or try one of the advanced suggestions.Advanced Suggestions• Make sure you have logged out of any earlier management sessions using the same user account even if they were through a different interface or using a different browser.• Try to access the Device using another service, such as Telnet. If you can access the Device, check the remote management settings and firewall rules to find out why the Device does not respond to HTTP. I can see the Login screen, but I cannot log in to the Device.1Make sure you have entered the password correctly. The default admin password is 1234. The fieldis case-sensitive, so make sure [Caps Lock] is not on. 2You cannot log in to the web configurator while someone is using Telnet to access the Device. Log out of the Device in the other session, or ask the person who is logged in to log out. 3Turn the Device off and on.4If this does not work, you have to reset the device to its factory defaults. See Section 36.1 on page 281.I cannot Telnet to the Device.See the troubleshooting suggestions for I cannot see or access the Login screen in the web configurator. Ignore the suggestions about your browser.I cannot use FTP to upload / download the configuration file. / I cannot use FTP to upload new firmware.See the troubleshooting suggestions for I cannot see or access the Login screen in the web configurator. Ignore the suggestions about your browser.36.3 Internet AccessI cannot access the Internet.
Chapter 36 TroubleshootingVMG4380-B10A / VMG4325-B10A User’s Guide2841Check the hardware connections, and make sure the LEDs are behaving as expected. See the Quick Start Guide and Section 1.5 on page 21.2Make sure you entered your ISP account information correctly in the Network Setting > Broadband screen. These fields are case-sensitive, so make sure [Caps Lock] is not on. 3If you are trying to access the Internet wirelessly, make sure that you enabled the wireless LAN in the Device and your wireless client and that the wireless settings in the wireless client are the sameas the settings in the Device.4Disconnect all the cables from your device and reconnect them. 5If the problem continues, contact your ISP.I cannot access the Internet through a DSL connection.1Make sure you have the DSL WAN port connected to a telephone jack (or the DSL or modem jack on a splitter if you have one).2Make sure you configured a proper DSL WAN interface (Network Setting > Broadband screen) with the Internet account information provided by your ISP and that it is enabled.3Check that the LAN interface you are connected to is in the same interface group as the DSL connection (Network Setting > Interface Group).4If you set up a WAN connection using bridging service, make sure you turn off the DHCP feature in the LAN screen to have the clients get WAN IP addresses directly from your ISP’s DHCP server.I cannot connect to the Internet using a second DSL connection.ADSL and VDSL connections cannot work at the same time. You can only use one type of DSL connection, either ADSL or VDSL connection at one time.I cannot access the Internet anymore. I had access to the Internet (with the Device), but myInternet connection is not available anymore.1Your session with the Device may have expired. Try logging into the Device again.2Check the hardware connections, and make sure the LEDs are behaving as expected. See the Quick Start Guide and Section 1.5 on page 21.3Turn the Device off and on.4If the problem continues, contact your ISP.
Chapter 36 TroubleshootingVMG4380-B10A / VMG4325-B10A User’s Guide 28536.4 Wireless Internet AccessWhat factors may cause intermittent or unstabled wireless connection? How can I solve this problem?The following factors may cause interference:• Obstacles: walls, ceilings, furniture, and so on.• Building Materials: metal doors, aluminum studs.• Electrical devices: microwaves, monitors, electric motors, cordless phones, and other wireless devices.To optimize the speed and quality of your wireless connection, you can:• Move your wireless device closer to the AP if the signal strength is low.• Reduce wireless interference that may be caused by other wireless networks or surrounding wireless electronics such as cordless phones.• Place the AP where there are minimum obstacles (such as walls and ceilings) between the AP and the wireless client. • Reduce the number of wireless clients connecting to the same AP simultaneously, or add additional APs if necessary.• Try closing some programs that use the Internet, especially peer-to-peer applications. If thewireless client is sending or receiving a lot of information, it may have too many programs open that use the Internet. What is a Server Set ID (SSID)?An SSID is a name that uniquely identifies a wireless network. The AP and all the clients within a wireless network must use the same SSID.What wireless security modes does my Device support?Wireless security is vital to your network. It protects communications between wireless stations, access points and the wired network. The available security modes in your Device are as follows:•WPA2-PSK: (recommended) This uses a pre-shared key with the WPA2 standard.•WPA-PSK: This has the device use either WPA-PSK or WPA2-PSK depending on which security mode the wireless client uses. •WPA2: WPA2 (IEEE 802.11i) is a wireless security standard that defines stronger encryption, authentication and key management than WPA. It requires the use of a RADIUS server and ismostly used in business networks.
Chapter 36 TroubleshootingVMG4380-B10A / VMG4325-B10A User’s Guide286•WPA: Wi-Fi Protected Access (WPA) is a subset of the IEEE 802.11i standard. It requires the useof a RADIUS server and is mostly used in business networks. •WEP: Wired Equivalent Privacy (WEP) encryption scrambles the data transmitted between the wireless stations and the access points to keep network communications private.36.5 USB Device ConnectionThe Device fails to detect my USB device.1Disconnect the USB device.2Reboot the Device.3If you are connecting a USB hard drive that comes with an external power supply, make sure it is connected to an appropriate power source that is on. 4Re-connect your USB device to the Device.36.6 UPnPWhen using UPnP and the Device reboots, my computer cannot detect UPnP and refresh My Network Places > Local Network.1Disconnect the Ethernet cable from the Device’s LAN port or from your computer.2Re-connect the Ethernet cable.The Local Area Connection icon for UPnP disappears in the screen.Restart your computer.I cannot open special applications such as white board, file transfer and video when I use the MSN messenger.1Wait more than three minutes.2Restart the applications.
VMG4380-B10A / VMG4325-B10A User’s Guide 287APPENDIX ASetting up Your Computer’s IP AddressAll computers must have a 10M or 100M Ethernet adapter card and TCP/IP installed. Windows 95/98/Me/NT/2000/XP/Vista, Macintosh OS 7 and later operating systems and all versions of UNIX/LINUX include the software components you need to install and use TCP/IP on your computer. Windows 3.1 requires the purchase of a third-party TCP/IP application package.TCP/IP should already be installed on computers using Windows NT/2000/XP, Macintosh OS 7 and later operating systems.After the appropriate TCP/IP components are installed, configure the TCP/IP settings in order to "communicate" with your network. If you manually assign IP information instead of using dynamic assignment, make sure that your computers have IP addresses that place them in the same subnet as the Device’s LAN port.Windows 95/98/MeClick Start, Settings, Control Panel and double-click the Network icon to open the Network window.Figure 152 WIndows 95/98/Me: Network: Configuration
Appendix A Setting up Your Computer’s IP AddressVMG4380-B10A / VMG4325-B10A User’s Guide288Installing ComponentsThe Network window Configuration tab displays a list of installed components. You need a network adapter, the TCP/IP protocol and Client for Microsoft Networks.If you need the adapter:1In the Network window, click Add.2Select Adapter and then click Add.3Select the manufacturer and model of your network adapter and then click OK.If you need TCP/IP:1In the Network window, click Add.2Select Protocol and then click Add.3Select Microsoft from the list of manufacturers.4Select TCP/IP from the list of network protocols and then click OK.If you need Client for Microsoft Networks:1Click Add.2Select Client and then click Add.3Select Microsoft from the list of manufacturers.4Select Client for Microsoft Networks from the list of network clients and then click OK.5Restart your computer so the changes you made take effect.Configuring 1In the Network window Configuration tab, select your network adapter's TCP/IP entry and click Properties2Click the IP Address tab.• If your IP address is dynamic, select Obtain an IP address automatically.
Appendix A Setting up Your Computer’s IP AddressVMG4380-B10A / VMG4325-B10A User’s Guide 289• If you have a static IP address, select Specify an IP address and type your information into the IP Address and Subnet Mask fields.Figure 153 Windows 95/98/Me: TCP/IP Properties: IP Address3Click the DNS Configuration tab.• If you do not know your DNS information, select Disable DNS.• If you know your DNS information, select Enable DNS and type the information in the fields below (you may not need to fill them all in).Figure 154 Windows 95/98/Me: TCP/IP Properties: DNS Configuration
Appendix A Setting up Your Computer’s IP AddressVMG4380-B10A / VMG4325-B10A User’s Guide2904Click the Gateway tab.• If you do not know your gateway’s IP address, remove previously installed gateways.• If you have a gateway IP address, type it in the New gateway field and click Add.5Click OK to save and close the TCP/IP Properties window.6Click OK to close the Network window. Insert the Windows CD if prompted.7Turn on your Device and restart your computer when prompted.Verifying Settings1Click Start and then Run.2In the Run window, type "winipcfg" and then click OK to open the IP Configuration window.3Select your network adapter. You should see your computer's IP address, subnet mask and default gateway.Windows 2000/NT/XPThe following example figures use the default Windows XP GUI theme.1Click start (Start in Windows 2000/NT), Settings, Control Panel.Figure 155 Windows XP: Start Menu
Appendix A Setting up Your Computer’s IP AddressVMG4380-B10A / VMG4325-B10A User’s Guide 2912In the Control Panel, double-click Network Connections (Network and Dial-up Connectionsin Windows 2000/NT).Figure 156 Windows XP: Control Panel3Right-click Local Area Connection and then click Properties.Figure 157 Windows XP: Control Panel: Network Connections: Properties
Appendix A Setting up Your Computer’s IP AddressVMG4380-B10A / VMG4325-B10A User’s Guide2924Select Internet Protocol (TCP/IP) (under the General tab in Win XP) and then click Properties.Figure 158 Windows XP: Local Area Connection Properties5The Internet Protocol TCP/IP Properties window opens (the General tab in Windows XP).• If you have a dynamic IP address click Obtain an IP address automatically.• If you have a static IP address click Use the following IP Address and fill in the IP address, Subnet mask, and Default gateway fields.
Appendix A Setting up Your Computer’s IP AddressVMG4380-B10A / VMG4325-B10A User’s Guide 293• Click Advanced.Figure 159 Windows XP: Internet Protocol (TCP/IP) Properties6If you do not know your gateway's IP address, remove any previously installed gateways in the IP Settings tab and click OK.Do one or more of the following if you want to configure additional IP addresses:• In the IP Settings tab, in IP addresses, click Add.• In TCP/IP Address, type an IP address in IP address and a subnet mask in Subnet mask, and then click Add.• Repeat the above two steps for each IP address you want to add.• Configure additional default gateways in the IP Settings tab by clicking Add in Default gateways.• In TCP/IP Gateway Address, type the IP address of the default gateway in Gateway. Tomanually configure a default metric (the number of transmission hops), clear the Automatic metric check box and type a metric in Metric.• Click Add. • Repeat the previous three steps for each default gateway you want to add.
Appendix A Setting up Your Computer’s IP AddressVMG4380-B10A / VMG4325-B10A User’s Guide294• Click OK when finished.Figure 160 Windows XP: Advanced TCP/IP Properties7In the Internet Protocol TCP/IP Properties window (the General tab in Windows XP):• Click Obtain DNS server address automatically if you do not know your DNS server IP address(es).• If you know your DNS server IP address(es), click Use the following DNS server addresses, and type them in the Preferred DNS server and Alternate DNS server fields.
Appendix A Setting up Your Computer’s IP AddressVMG4380-B10A / VMG4325-B10A User’s Guide 295If you have previously configured DNS servers, click Advanced and then the DNS tab to order them.Figure 161 Windows XP: Internet Protocol (TCP/IP) Properties8Click OK to close the Internet Protocol (TCP/IP) Properties window.9Click Close (OK in Windows 2000/NT) to close the Local Area Connection Properties window.10 Close the Network Connections window (Network and Dial-up Connections in Windows2000/NT).11 Turn on your Device and restart your computer (if prompted).Verifying Settings1Click Start, All Programs, Accessories and then Command Prompt.2In the Command Prompt window, type "ipconfig" and then press [ENTER]. You can also open Network Connections, right-click a network connection, click Status and then click the Support tab.Windows VistaThis section shows screens from Windows Vista Enterprise Version 6.0.
Appendix A Setting up Your Computer’s IP AddressVMG4380-B10A / VMG4325-B10A User’s Guide2961Click the Start icon, Control Panel.Figure 162 Windows Vista: Start Menu2In the Control Panel, double-click Network and Internet.Figure 163 Windows Vista: Control Panel3Click Network and Sharing Center.Figure 164 Windows Vista: Network And Internet
Appendix A Setting up Your Computer’s IP AddressVMG4380-B10A / VMG4325-B10A User’s Guide 2974Click Manage network connections.Figure 165 Windows Vista: Network and Sharing Center5Right-click Local Area Connection and then click Properties.Note: During this procedure, click Continue whenever Windows displays a screen sayingthat it needs your permission to continue.Figure 166 Windows Vista: Network and Sharing Center
Appendix A Setting up Your Computer’s IP AddressVMG4380-B10A / VMG4325-B10A User’s Guide2986Select Internet Protocol Version 4 (TCP/IPv4) and click Properties.Figure 167 Windows Vista: Local Area Connection Properties7The Internet Protocol Version 4 (TCP/IPv4) Properties window opens (the General tab).• If you have a dynamic IP address click Obtain an IP address automatically.• If you have a static IP address click Use the following IP address and fill in the IP address, Subnet mask, and Default gateway fields.
Appendix A Setting up Your Computer’s IP AddressVMG4380-B10A / VMG4325-B10A User’s Guide 299• Click Advanced.Figure 168 Windows Vista: Internet Protocol Version 4 (TCP/IPv4) Properties8If you do not know your gateway's IP address, remove any previously installed gateways in the IP Settings tab and click OK.Do one or more of the following if you want to configure additional IP addresses:• In the IP Settings tab, in IP addresses, click Add.• In TCP/IP Address, type an IP address in IP address and a subnet mask in Subnet mask, and then click Add.• Repeat the above two steps for each IP address you want to add.• Configure additional default gateways in the IP Settings tab by clicking Add in Default gateways.• In TCP/IP Gateway Address, type the IP address of the default gateway in Gateway. Tomanually configure a default metric (the number of transmission hops), clear the Automatic metric check box and type a metric in Metric.• Click Add. • Repeat the previous three steps for each default gateway you want to add.
Appendix A Setting up Your Computer’s IP AddressVMG4380-B10A / VMG4325-B10A User’s Guide300• Click OK when finished.Figure 169 Windows Vista: Advanced TCP/IP Properties9In the Internet Protocol Version 4 (TCP/IPv4) Properties window, (the General tab):• Click Obtain DNS server address automatically if you do not know your DNS server IP address(es).• If you know your DNS server IP address(es), click Use the following DNS server addresses, and type them in the Preferred DNS server and Alternate DNS server fields.
Appendix A Setting up Your Computer’s IP AddressVMG4380-B10A / VMG4325-B10A User’s Guide 301If you have previously configured DNS servers, click Advanced and then the DNS tab to order them.Figure 170 Windows Vista: Internet Protocol Version 4 (TCP/IPv4) Properties10 Click OK to close the Internet Protocol Version 4 (TCP/IPv4) Properties window.11 Click Close to close the Local Area Connection Properties window.12 Close the Network Connections window.13 Turn on your Device and restart your computer (if prompted).Verifying Settings1Click Start, All Programs, Accessories and then Command Prompt.2In the Command Prompt window, type "ipconfig" and then press [ENTER]. You can also open Network Connections, right-click a network connection, click Status and then click the Support tab.
Appendix A Setting up Your Computer’s IP AddressVMG4380-B10A / VMG4325-B10A User’s Guide302Macintosh OS 8/9 1Click the Apple menu, Control Panel and double-click TCP/IP to open the TCP/IP Control Panel.Figure 171 Macintosh OS 8/9: Apple Menu
Appendix A Setting up Your Computer’s IP AddressVMG4380-B10A / VMG4325-B10A User’s Guide 3032Select Ethernet built-in from the Connect via list.Figure 172 Macintosh OS 8/9: TCP/IP3For dynamically assigned settings, select Using DHCP Server from the Configure: list.4For statically assigned settings, do the following:• From the Configure box, select Manually.• Type your IP address in the IP Address box.• Type your subnet mask in the Subnet mask box.• Type the IP address of your Device in the Router address box.5Close the TCP/IP Control Panel.6Click Save if prompted, to save changes to your configuration.7Turn on your Device and restart your computer (if prompted).Verifying SettingsCheck your TCP/IP properties in the TCP/IP Control Panel window.Macintosh OS X1Click the Apple menu, and click System Preferences to open the System Preferences window.Figure 173 Macintosh OS X: Apple Menu2Click Network in the icon bar. • Select Automatic from the Location list.
Appendix A Setting up Your Computer’s IP AddressVMG4380-B10A / VMG4325-B10A User’s Guide304• Select Built-in Ethernet from the Show list. • Click the TCP/IP tab.3For dynamically assigned settings, select Using DHCP from the Configure list.Figure 174 Macintosh OS X: Network4For statically assigned settings, do the following:• From the Configure box, select Manually.• Type your IP address in the IP Address box.• Type your subnet mask in the Subnet mask box.• Type the IP address of your Device in the Router address box.5Click Apply Now and close the window.6Turn on your Device and restart your computer (if prompted).Verifying SettingsCheck your TCP/IP properties in the Network window.
Appendix A Setting up Your Computer’s IP AddressVMG4380-B10A / VMG4325-B10A User’s Guide 305Linux This section shows you how to configure your computer’s TCP/IP settings in Red Hat Linux 9.0. Procedure, screens and file location may vary depending on your Linux distribution and releaseversion.Note: Make sure you are logged in as the root administrator.Using the K Desktop Environment (KDE)Follow the steps below to configure your computer IP address using the KDE. 1Click the Red Hat button (located on the bottom left corner), select System Setting and click Network.Figure 175 Red Hat 9.0: KDE: Network Configuration: Devices
Appendix A Setting up Your Computer’s IP AddressVMG4380-B10A / VMG4325-B10A User’s Guide3062Double-click on the profile of the network card you wish to configure. The Ethernet DeviceGeneral screen displays as shown. Figure 176 Red Hat 9.0: KDE: Ethernet Device: General • If you have a dynamic IP address, click Automatically obtain IP address settings with and select dhcp from the drop down list. • If you have a static IP address, click Statically set IP Addresses and fill in the Address, Subnet mask, and Default Gateway Address fields. 3Click OK to save the changes and close the Ethernet Device General screen. 4If you know your DNS server IP address(es), click the DNS tab in the Network Configurationscreen. Enter the DNS server information in the fields provided.Figure 177 Red Hat 9.0: KDE: Network Configuration: DNS 5Click the Devices tab.
Appendix A Setting up Your Computer’s IP AddressVMG4380-B10A / VMG4325-B10A User’s Guide 3076Click the Activate button to apply the changes. The following screen displays. Click Yes to save the changes in all screens.Figure 178 Red Hat 9.0: KDE: Network Configuration: Activate7After the network card restart process is complete, make sure the Status is Active in the Network Configuration screen.Using Configuration FilesFollow the steps below to edit the network configuration files and set your computer IP address. 1Assuming that you have only one network card on the computer, locate the ifconfig-eth0configuration file (where eth0 is the name of the Ethernet card). Open the configuration file with any plain text editor.• If you have a dynamic IP address, enter dhcp in the BOOTPROTO= field. The following figure shows an example. Figure 179 Red Hat 9.0: Dynamic IP Address Setting in ifconfig-eth0 • If you have a static IP address, enter static in the BOOTPROTO= field. Type IPADDR= followedby the IP address (in dotted decimal notation) and type NETMASK= followed by the subnet mask. The following example shows an example where the static IP address is 192.168.1.10 and the subnet mask is 255.255.255.0. Figure 180 Red Hat 9.0: Static IP Address Setting in ifconfig-eth0 DEVICE=eth0ONBOOT=yesBOOTPROTO=dhcpUSERCTL=noPEERDNS=yesTYPE=EthernetDEVICE=eth0ONBOOT=yesBOOTPROTO=staticIPADDR=192.168.1.10NETMASK=255.255.255.0USERCTL=noPEERDNS=yesTYPE=Ethernet
Appendix A Setting up Your Computer’s IP AddressVMG4380-B10A / VMG4325-B10A User’s Guide3082If you know your DNS server IP address(es), enter the DNS server information in the resolv.conffile in the /etc directory. The following figure shows an example where two DNS server IP addresses are specified.Figure 181 Red Hat 9.0: DNS Settings in resolv.conf 3After you edit and save the configuration files, you must restart the network card. Enter ./network restart in the /etc/rc.d/init.d directory. The following figure shows an example.Figure 182 Red Hat 9.0: Restart Ethernet Card Verifying SettingsEnter ifconfig in a terminal screen to check your TCP/IP properties. Figure 183 Red Hat 9.0: Checking TCP/IP Propertiesnameserver 172.23.5.1nameserver 172.23.5.2[root@localhost init.d]# network restartShutting down interface eth0: [OK]Shutting down loopback interface: [OK]Setting network parameters: [OK]Bringing up loopback interface: [OK]Bringing up interface eth0: [OK][root@localhost]# ifconfig eth0 Link encap:Ethernet HWaddr 00:50:BA:72:5B:44 inet addr:172.23.19.129 Bcast:172.23.19.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:717 errors:0 dropped:0 overruns:0 frame:0 TX packets:13 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:730412 (713.2 Kb) TX bytes:1570 (1.5 Kb) Interrupt:10 Base address:0x1000 [root@localhost]#
VMG4380-B10A / VMG4325-B10A User’s Guide 309APPENDIX BIP Addresses and SubnettingThis appendix introduces IP addresses and subnet masks. IP addresses identify individual devices on a network. Every networking device (including computers, servers, routers, printers, etc.) needs an IP address to communicate across thenetwork. These networking devices are also known as hosts.Subnet masks determine the maximum number of possible hosts on a network. You can also use subnet masks to divide one network into multiple sub-networks.Introduction to IP AddressesOne part of the IP address is the network number, and the other part is the host ID. In the same way that houses on a street share a common street name, the hosts on a network share a common network number. Similarly, as each house has its own house number, each host on the network has its own unique identifying number - the host ID. Routers use the network number to send packets to the correct network, while the host ID determines to which host on the network the packets are delivered.StructureAn IP address is made up of four parts, written in dotted decimal notation (for example, 192.168.1.1). Each of these four parts is known as an octet. An octet is an eight-digit binary number (for example 11000000, which is 192 in decimal notation).Therefore, each octet has a possible range of 00000000 to 11111111 in binary, or 0 to 255 in decimal.
Appendix B IP Addresses and SubnettingVMG4380-B10A / VMG4325-B10A User’s Guide310The following figure shows an example IP address in which the first three octets (192.168.1) are the network number, and the fourth octet (16) is the host ID.Figure 184 Network Number and Host IDHow much of the IP address is the network number and how much is the host ID varies according to the subnet mask.Subnet MasksA subnet mask is used to determine which bits are part of the network number, and which bits are part of the host ID (using a logical AND operation). The term “subnet” is short for “sub-network”.A subnet mask has 32 bits. If a bit in the subnet mask is a “1” then the corresponding bit in the IPaddress is part of the network number. If a bit in the subnet mask is “0” then the corresponding bit in the IP address is part of the host ID. The following example shows a subnet mask identifying the network number (in bold text) and host ID of an IP address (192.168.1.2 in decimal).By convention, subnet masks always consist of a continuous sequence of ones beginning from the leftmost bit of the mask, followed by a continuous sequence of zeros, for a total number of 32 bits.Table 113 Subnet Masks1ST OCTET:(192)2ND OCTET:(168)3RD OCTET:(1)4TH OCTET(2)IP Address (Binary) 11000000 10101000 00000001 00000010Subnet Mask (Binary) 11111111 11111111 11111111 00000000Network Number 11000000 10101000 00000001Host ID 00000010
Appendix B IP Addresses and SubnettingVMG4380-B10A / VMG4325-B10A User’s Guide 311Subnet masks can be referred to by the size of the network number part (the bits with a “1” value). For example, an “8-bit mask” means that the first 8 bits of the mask are ones and the remaining 24 bits are zeroes.Subnet masks are expressed in dotted decimal notation just like IP addresses. The following examples show the binary and decimal notation for 8-bit, 16-bit, 24-bit and 29-bit subnet masks. Network SizeThe size of the network number determines the maximum number of possible hosts you can haveon your network. The larger the number of network number bits, the smaller the number of remaining host ID bits. An IP address with host IDs of all zeros is the IP address of the network (192.168.1.0 with a 24-bit subnet mask, for example). An IP address with host IDs of all ones is the broadcast address for that network (192.168.1.255 with a 24-bit subnet mask, for example).As these two IP addresses cannot be used for individual hosts, calculate the maximum number of possible hosts in a network as follows:NotationSince the mask is always a continuous number of ones beginning from the left, followed by a continuous number of zeros for the remainder of the 32 bit mask, you can simply specify thenumber of ones instead of writing the value of each octet. This is usually specified by writing a “/” followed by the number of bits in the mask after the address. For example, 192.1.1.0 /25 is equivalent to saying 192.1.1.0 with subnet mask 255.255.255.128.Table 114 Subnet MasksBINARYDECIMAL1STOCTET2NDOCTET3RD OCTET 4TH OCTET8-bit mask 11111111 00000000 00000000 00000000 255.0.0.016-bit mask 11111111 11111111 00000000 00000000 255.255.0.024-bit mask 11111111 11111111 11111111 00000000 255.255.255.029-bit mask 11111111 11111111 11111111 11111000 255.255.255.248Table 115 Maximum Host NumbersSUBNET MASK HOST ID SIZE MAXIMUM NUMBER OF HOSTS8 bits 255.0.0.0 24 bits 224 – 2 1677721416 bits 255.255.0.0 16 bits 216 – 2 6553424 bits 255.255.255.0 8 bits 28 – 2 25429 bits 255.255.255.2483 bits 23 – 2 6
Appendix B IP Addresses and SubnettingVMG4380-B10A / VMG4325-B10A User’s Guide312The following table shows some possible subnet masks using both notations. SubnettingYou can use subnetting to divide one network into multiple sub-networks. In the following example a network administrator creates two sub-networks to isolate a group of servers from the rest of the company network for security reasons.In this example, the company network address is 192.168.1.0. The first three octets of the address (192.168.1) are the network number, and the remaining octet is the host ID, allowing a maximum of 28 – 2 or 254 possible hosts.The following figure shows the company network before subnetting. Figure 185 Subnetting Example: Before SubnettingYou can “borrow” one of the host ID bits to divide the network 192.168.1.0 into two separate sub-networks. The subnet mask is now 25 bits (255.255.255.128 or /25).The “borrowed” host ID bit can have a value of either 0 or 1, allowing two subnets; 192.168.1.0 /25 and 192.168.1.128 /25.Table 116 Alternative Subnet Mask NotationSUBNET MASK ALTERNATIVE NOTATIONLAST OCTET (BINARY)LAST OCTET (DECIMAL)255.255.255.0 /24 0000 0000 0255.255.255.128 /25 1000 0000 128255.255.255.192 /26 1100 0000 192255.255.255.224 /27 1110 0000 224255.255.255.240 /28 1111 0000 240255.255.255.248 /29 1111 1000 248255.255.255.252 /30 1111 1100 252
Appendix B IP Addresses and SubnettingVMG4380-B10A / VMG4325-B10A User’s Guide 313The following figure shows the company network after subnetting. There are now two sub-networks, A and B. Figure 186 Subnetting Example: After SubnettingIn a 25-bit subnet the host ID has 7 bits, so each sub-network has a maximum of 27 – 2 or 126possible hosts (a host ID of all zeroes is the subnet’s address itself, all ones is the subnet’sbroadcast address).192.168.1.0 with mask 255.255.255.128 is subnet A itself, and 192.168.1.127 with mask 255.255.255.128 is its broadcast address. Therefore, the lowest IP address that can be assigned to an actual host for subnet A is 192.168.1.1 and the highest is 192.168.1.126.Similarly, the host ID range for subnet Bis 192.168.1.129 to 192.168.1.254.Example: Four Subnets The previous example illustrated using a 25-bit subnet mask to divide a 24-bit address into two subnets. Similarly, to divide a 24-bit address into four subnets, you need to “borrow” two host ID bits to give four possible combinations (00, 01, 10 and 11). The subnet mask is 26 bits (11111111.11111111.11111111.11000000) or 255.255.255.192. Each subnet contains 6 host ID bits, giving 26- 2 or 62 hosts for each subnet (a host ID of all zeroes is the subnet itself, all ones is the subnet’s broadcast address).Table 117 Subnet 1IP/SUBNET MASK NETWORK NUMBER LAST OCTET BIT VALUEIP Address (Decimal) 192.168.1. 0IP Address (Binary) 11000000.10101000.00000001. 00000000Subnet Mask (Binary) 11111111.11111111.11111111. 11000000
Appendix B IP Addresses and SubnettingVMG4380-B10A / VMG4325-B10A User’s Guide314Example: Eight SubnetsSimilarly, use a 27-bit mask to create eight subnets (000, 001, 010, 011, 100, 101, 110 and 111). The following table shows IP address last octet values for each subnet.Subnet Address: 192.168.1.0Lowest Host ID: 192.168.1.1Broadcast Address: 192.168.1.63Highest Host ID: 192.168.1.62Table 118 Subnet 2IP/SUBNET MASK NETWORK NUMBER LAST OCTET BIT VALUEIP Address 192.168.1. 64IP Address (Binary) 11000000.10101000.00000001. 01000000Subnet Mask (Binary) 11111111.11111111.11111111. 11000000Subnet Address: 192.168.1.64Lowest Host ID: 192.168.1.65Broadcast Address: 192.168.1.127Highest Host ID: 192.168.1.126Table 119 Subnet 3IP/SUBNET MASK NETWORK NUMBER LAST OCTET BIT VALUEIP Address 192.168.1. 128IP Address (Binary) 11000000.10101000.00000001. 10000000Subnet Mask (Binary) 11111111.11111111.11111111. 11000000Subnet Address: 192.168.1.128Lowest Host ID: 192.168.1.129Broadcast Address: 192.168.1.191Highest Host ID: 192.168.1.190Table 120 Subnet 4IP/SUBNET MASK NETWORK NUMBER LAST OCTET BIT VALUEIP Address 192.168.1. 192IP Address (Binary) 11000000.10101000.00000001. 11000000Subnet Mask (Binary) 11111111.11111111.11111111. 11000000Subnet Address: 192.168.1.192Lowest Host ID: 192.168.1.193Broadcast Address: 192.168.1.255Highest Host ID: 192.168.1.254Table 117 Subnet 1 (continued)IP/SUBNET MASK NETWORK NUMBER LAST OCTET BIT VALUETable 121 Eight SubnetsSUBNET SUBNET ADDRESS FIRST ADDRESS LASTADDRESSBROADCAST ADDRESS1 0 1 30 312 32 33 62 63
Appendix B IP Addresses and SubnettingVMG4380-B10A / VMG4325-B10A User’s Guide 315Subnet PlanningThe following table is a summary for subnet planning on a network with a 24-bit network number.The following table is a summary for subnet planning on a network with a 16-bit network number. 3 64 65 94 954 96 97 126 1275 128 129 158 1596 160 161 190 1917 192 193 222 2238 224 225 254 255Table 121 Eight Subnets (continued)SUBNET SUBNET ADDRESS FIRST ADDRESS LASTADDRESSBROADCAST ADDRESSTable 122 24-bit Network Number Subnet PlanningNO. “BORROWED” HOST BITS SUBNET MASK NO. SUBNETS NO. HOSTS PERSUBNET1 255.255.255.128 (/25) 2 1262 255.255.255.192 (/26) 4 623 255.255.255.224 (/27) 8 304 255.255.255.240 (/28) 16 145 255.255.255.248 (/29) 32 66 255.255.255.252 (/30) 64 27 255.255.255.254 (/31) 128 1Table 123 16-bit Network Number Subnet PlanningNO. “BORROWED” HOST BITS SUBNET MASK NO. SUBNETS NO. HOSTS PER SUBNET1 255.255.128.0 (/17) 2 327662 255.255.192.0 (/18) 4 163823 255.255.224.0 (/19) 8 81904 255.255.240.0 (/20) 16 40945 255.255.248.0 (/21) 32 20466 255.255.252.0 (/22) 64 10227 255.255.254.0 (/23) 128 5108 255.255.255.0 (/24) 256 2549 255.255.255.128 (/25) 512 12610 255.255.255.192 (/26) 1024 6211 255.255.255.224 (/27) 2048 3012 255.255.255.240 (/28) 4096 1413 255.255.255.248 (/29) 8192 614 255.255.255.252 (/30) 16384 215 255.255.255.254 (/31) 32768 1
Appendix B IP Addresses and SubnettingVMG4380-B10A / VMG4325-B10A User’s Guide316Configuring IP AddressesWhere you obtain your network number depends on your particular situation. If the ISP or your network administrator assigns you a block of registered IP addresses, follow their instructions inselecting the IP addresses and the subnet mask.If the ISP did not explicitly give you an IP network number, then most likely you have a single user account and the ISP will assign you a dynamic IP address when the connection is established. If this is the case, it is recommended that you select a network number from 192.168.0.0 to 192.168.255.0. The Internet Assigned Number Authority (IANA) reserved this block of addressesspecifically for private use; please do not use any other number unless you are told otherwise. You must also enable Network Address Translation (NAT) on the Device. Once you have decided on the network number, pick an IP address for your Device that is easy to remember (for instance, 192.168.1.1) but make sure that no other device on your network is using that IP address.The subnet mask specifies the network number portion of an IP address. Your Device will computethe subnet mask automatically based on the IP address that you entered. You don't need to change the subnet mask computed by the Device unless you are instructed to do otherwise.Private IP AddressesEvery machine on the Internet must have a unique address. If your networks are isolated from the Internet (running only between two branch offices, for example) you can assign any IP addresses to the hosts without problems. However, the Internet Assigned Numbers Authority (IANA) has reserved the following three blocks of IP addresses specifically for private networks:• 10.0.0.0 — 10.255.255.255• 172.16.0.0 — 172.31.255.255• 192.168.0.0 — 192.168.255.255You can obtain your IP address from the IANA, from an ISP, or it can be assigned from a private network. If you belong to a small organization and your Internet access is through an ISP, the ISP can provide you with the Internet addresses for your local networks. On the other hand, if you are part of a much larger organization, you should consult your network administrator for the appropriate IP addresses.Regardless of your particular situation, do not create an arbitrary IP address; always follow the guidelines above. For more information on address assignment, please refer to RFC 1597, Address Allocation for Private Internets and RFC 1466, Guidelines for Management of IP Address Space.
VMG4380-B10A / VMG4325-B10A User’s Guide 317APPENDIX CPop-up Windows, JavaScripts and JavaPermissionsIn order to use the web configurator you need to allow:• Web browser pop-up windows from your device.• JavaScripts (enabled by default).• Java permissions (enabled by default).Note: Internet Explorer 6 screens are used here. Screens for other Internet Explorerversions may vary.Internet Explorer Pop-up BlockersYou may have to disable pop-up blocking to log into your device. Either disable pop-up blocking (enabled by default in Windows XP SP (Service Pack) 2) or allow pop-up blocking and create an exception for your device’s IP address.Disable Pop-up Blockers1In Internet Explorer, select Tools, Pop-up Blocker and then select Turn Off Pop-up Blocker. Figure 187 Pop-up BlockerYou can also check if pop-up blocking is disabled in the Pop-up Blocker section in the Privacy tab.1In Internet Explorer, select Tools, Internet Options, Privacy.
Appendix C Pop-up Windows, JavaScripts and Java PermissionsVMG4380-B10A / VMG4325-B10A User’s Guide3182Clear the Block pop-ups check box in the Pop-up Blocker section of the screen. This disables any web pop-up blockers you may have enabled.Figure 188 Internet Options: Privacy3Click Apply to save this setting.Enable Pop-up Blockers with ExceptionsAlternatively, if you only want to allow pop-up windows from your device, see the following steps.1In Internet Explorer, select Tools, Internet Options and then the Privacy tab.
Appendix C Pop-up Windows, JavaScripts and Java PermissionsVMG4380-B10A / VMG4325-B10A User’s Guide 3192Select Settings…to open the Pop-up Blocker Settings screen.Figure 189 Internet Options: Privacy3Type the IP address of your device (the web page that you do not want to have blocked) with the prefix “http://”. For example, http://192.168.167.1.
Appendix C Pop-up Windows, JavaScripts and Java PermissionsVMG4380-B10A / VMG4325-B10A User’s Guide3204Click Add to move the IP address to the list of Allowed sites.Figure 190 Pop-up Blocker Settings5Click Close to return to the Privacy screen. 6Click Apply to save this setting. JavaScriptsIf pages of the web configurator do not display properly in Internet Explorer, check that JavaScripts are allowed.
Appendix C Pop-up Windows, JavaScripts and Java PermissionsVMG4380-B10A / VMG4325-B10A User’s Guide 3211In Internet Explorer, click Tools, Internet Options and then the Security tab.Figure 191 Internet Options: Security 2Click the Custom Level... button.3Scroll down to Scripting. 4Under Active scripting make sure that Enable is selected (the default).5Under Scripting of Java applets make sure that Enable is selected (the default).
Appendix C Pop-up Windows, JavaScripts and Java PermissionsVMG4380-B10A / VMG4325-B10A User’s Guide3226Click OK to close the window.Figure 192 Security Settings - Java ScriptingJava Permissions1From Internet Explorer, click Tools, Internet Options and then the Security tab.2Click the Custom Level... button.3Scroll down to Microsoft VM. 4Under Java permissions make sure that a safety level is selected.
Appendix C Pop-up Windows, JavaScripts and Java PermissionsVMG4380-B10A / VMG4325-B10A User’s Guide 3235Click OK to close the window.Figure 193 Security Settings - JavaJAVA (Sun)1From Internet Explorer, click Tools, Internet Options and then the Advanced tab.2Make sure that Use Java 2 for <applet> under Java (Sun) is selected.
Appendix C Pop-up Windows, JavaScripts and Java PermissionsVMG4380-B10A / VMG4325-B10A User’s Guide3243Click OK to close the window.Figure 194 Java (Sun)Mozilla FirefoxMozilla Firefox 2.0 screens are used here. Screens for other versions may vary. You can enable Java, Javascripts and pop-ups in one screen. Click Tools, then click Options in the screen that appears.Figure 195 Mozilla Firefox: Tools > Options
Appendix C Pop-up Windows, JavaScripts and Java PermissionsVMG4380-B10A / VMG4325-B10A User’s Guide 325Click Content.to show the screen below. Select the check boxes as shown in the following screen.Figure 196 Mozilla Firefox Content Security
Appendix C Pop-up Windows, JavaScripts and Java PermissionsVMG4380-B10A / VMG4325-B10A User’s Guide326
VMG4380-B10A / VMG4325-B10A User’s Guide 327APPENDIX DWireless LANsWireless LAN TopologiesThis section discusses ad-hoc and infrastructure wireless LAN topologies.Ad-hoc Wireless LAN ConfigurationThe simplest WLAN configuration is an independent (Ad-hoc) WLAN that connects a set of computers with wireless adapters (A, B, C). Any time two or more wireless adapters are within range of each other, they can set up an independent network, which is commonly referred to as an ad-hoc network or Independent Basic Service Set (IBSS). The following diagram shows an example of notebook computers using wireless adapters to form an ad-hoc wireless LAN. Figure 197 Peer-to-Peer Communication in an Ad-hoc NetworkBSSA Basic Service Set (BSS) exists when all communications between wireless clients or between a wireless client and a wired network client go through one access point (AP). Intra-BSS traffic is traffic between wireless clients in the BSS. When Intra-BSS is enabled, wireless client A and B can access the wired network and communicate with each other. When Intra-BSS is
Appendix D Wireless LANsVMG4380-B10A / VMG4325-B10A User’s Guide328disabled, wireless client A and B can still access the wired network but cannot communicate with each other.Figure 198 Basic Service SetESSAn Extended Service Set (ESS) consists of a series of overlapping BSSs, each containing an accesspoint, with each access point connected together by a wired network. This wired connection between APs is called a Distribution System (DS).This type of wireless LAN topology is called an Infrastructure WLAN. The Access Points not only provide communication with the wired network but also mediate wireless network traffic in the immediate neighborhood.
Appendix D Wireless LANsVMG4380-B10A / VMG4325-B10A User’s Guide 329An ESSID (ESS IDentification) uniquely identifies each ESS. All access points and their associated wireless clients within the same ESS must have the same ESSID in order to communicate.Figure 199 Infrastructure WLANChannelA channel is the radio frequency(ies) used by wireless devices to transmit and receive data. Channels available depend on your geographical area. You may have a choice of channels (for your region) so you should use a channel different from an adjacent AP (access point) to reduceinterference. Interference occurs when radio signals from different access points overlap causing interference and degrading performance.Adjacent channels partially overlap however. To avoid interference due to overlap, your AP should be on a channel at least five channels away from a channel that an adjacent AP is using. For example, if your region has 11 channels and an adjacent AP is using channel 1, then you need to select a channel between 6 or 11.RTS/CTSA hidden node occurs when two stations are within range of the same access point, but are not within range of each other. The following figure illustrates a hidden node. Both stations (STA) are within range of the access point (AP) or wireless gateway, but out-of-range of each other, so they
Appendix D Wireless LANsVMG4380-B10A / VMG4325-B10A User’s Guide330cannot "hear" each other, that is they do not know if the channel is currently being used. Therefore, they are considered hidden from each other.Figure 200 RTS/CTSWhen station A sends data to the AP, it might not know that the station B is already using the channel. If these two stations send data at the same time, collisions may occur when both sets of data arrive at the AP at the same time, resulting in a loss of messages for both stations.RTS/CTS is designed to prevent collisions due to hidden nodes. An RTS/CTS defines the biggest size data frame you can send before an RTS (Request To Send)/CTS (Clear to Send) handshake is invoked.When a data frame exceeds the RTS/CTS value you set (between 0 to 2432 bytes), the station that wants to transmit this frame must first send an RTS (Request To Send) message to the AP for permission to send it. The AP then responds with a CTS (Clear to Send) message to all other stations within its range to notify them to defer their transmission. It also reserves and confirms with the requesting station the time frame for the requested transmission.Stations can send frames smaller than the specified RTS/CTS directly to the AP without the RTS (Request To Send)/CTS (Clear to Send) handshake. You should only configure RTS/CTS if the possibility of hidden nodes exists on your network and the "cost" of resending large frames is more than the extra network overhead involved in the RTS (Request To Send)/CTS (Clear to Send) handshake. If the RTS/CTS value is greater than the Fragmentation Threshold value (see next), then theRTS (Request To Send)/CTS (Clear to Send) handshake will never occur as data frames will be fragmented before they reach RTS/CTS size. Note: Enabling the RTS Threshold causes redundant network overhead that could negatively affect the throughput performance instead of providing a remedy.Fragmentation ThresholdA Fragmentation Threshold is the maximum data fragment size (between 256 and 2432 bytes) that can be sent in the wireless network before the AP will fragment the packet into smaller data frames.A large Fragmentation Threshold is recommended for networks not prone to interference while you should set a smaller threshold for busy networks or networks that are prone to interference.
Appendix D Wireless LANsVMG4380-B10A / VMG4325-B10A User’s Guide 331If the Fragmentation Threshold value is smaller than the RTS/CTS value (see previously) you set then the RTS (Request To Send)/CTS (Clear to Send) handshake will never occur as data frames will be fragmented before they reach RTS/CTS size.IEEE 802.11g Wireless LANIEEE 802.11g is fully compatible with the IEEE 802.11b standard. This means an IEEE 802.11badapter can interface directly with an IEEE 802.11g access point (and vice versa) at 11 Mbps orlower depending on range. IEEE 802.11g has several intermediate rate steps between the maximum and minimum data rates. The IEEE 802.11g data rate and modulation are as follows:Wireless Security OverviewWireless security is vital to your network to protect wireless communication between wireless clients, access points and the wired network.Wireless security methods available on the Device are data encryption, wireless client authentication, restricting access by device MAC address and hiding the Device identity.The following figure shows the relative effectiveness of these wireless security methods available onyour Device.Note: You must enable the same wireless security settings on the Device and on allwireless clients that you want to associate with it.Table 124 IEEE 802.11gDATA RATE (MBPS) MODULATION1 DBPSK (Differential Binary Phase Shift Keyed)2 DQPSK (Differential Quadrature Phase Shift Keying)5.5 / 11 CCK (Complementary Code Keying) 6/9/12/18/24/36/48/54OFDM (Orthogonal Frequency Division Multiplexing)Table 125 Wireless Security LevelsSECURITY LEVEL SECURITY TYPELeast SecureMost SecureUnique SSID (Default)Unique SSID with Hide SSID EnabledMAC Address FilteringWEP EncryptionIEEE802.1x EAP with RADIUS Server AuthenticationWi-Fi Protected Access (WPA)WPA2
Appendix D Wireless LANsVMG4380-B10A / VMG4325-B10A User’s Guide332IEEE 802.1xIn June 2001, the IEEE 802.1x standard was designed to extend the features of IEEE 802.11 to support extended authentication as well as providing additional accounting and control features. Itis supported by Windows XP and a number of network devices. Some advantages of IEEE 802.1x are:• User based identification that allows for roaming.• Support for RADIUS (Remote Authentication Dial In User Service, RFC 2138, 2139) for centralized user profile and accounting management on a network RADIUS server.• Support for EAP (Extensible Authentication Protocol, RFC 2486) that allows additional authentication methods to be deployed with no changes to the access point or the wireless clients. RADIUSRADIUS is based on a client-server model that supports authentication, authorization and accounting. The access point is the client and the server is the RADIUS server. The RADIUS serverhandles the following tasks:• Authentication Determines the identity of the users.• AuthorizationDetermines the network services available to authenticated users once they are connected to the network.• AccountingKeeps track of the client’s network activity. RADIUS is a simple package exchange in which your AP acts as a message relay between the wireless client and the network RADIUS server. Types of RADIUS MessagesThe following types of RADIUS messages are exchanged between the access point and the RADIUS server for user authentication:• Access-RequestSent by an access point requesting authentication.• Access-RejectSent by a RADIUS server rejecting access.• Access-AcceptSent by a RADIUS server allowing access. • Access-ChallengeSent by a RADIUS server requesting more information in order to allow access. The access point sends a proper response from the user and then sends another Access-Request message. The following types of RADIUS messages are exchanged between the access point and the RADIUS server for user accounting:
Appendix D Wireless LANsVMG4380-B10A / VMG4325-B10A User’s Guide 333• Accounting-RequestSent by the access point requesting accounting.• Accounting-ResponseSent by the RADIUS server to indicate that it has started or stopped accounting. In order to ensure network security, the access point and the RADIUS server use a shared secret key, which is a password, they both know. The key is not sent over the network. In addition to the shared key, password information exchanged is also encrypted to protect the network fromunauthorized access. Types of EAP Authentication This section discusses some popular authentication types: EAP-MD5, EAP-TLS, EAP-TTLS, PEAP andLEAP. Your wireless LAN device may not support all authentication types. EAP (Extensible Authentication Protocol) is an authentication protocol that runs on top of the IEEE 802.1x transport mechanism in order to support multiple types of user authentication. By using EAP to interact with an EAP-compatible RADIUS server, an access point helps a wireless station and a RADIUS server perform authentication. The type of authentication you use depends on the RADIUS server and an intermediary AP(s) that supports IEEE 802.1x. For EAP-TLS authentication type, you must first have a wired connection to the network and obtainthe certificate(s) from a certificate authority (CA). A certificate (also called digital IDs) can be used to authenticate users and a CA issues certificates and guarantees the identity of each certificate owner.EAP-MD5 (Message-Digest Algorithm 5)MD5 authentication is the simplest one-way authentication method. The authentication server sends a challenge to the wireless client. The wireless client ‘proves’ that it knows the password by encrypting the password with the challenge and sends back the information. Password is not sent in plain text. However, MD5 authentication has some weaknesses. Since the authentication server needs to get the plaintext passwords, the passwords must be stored. Thus someone other than the authentication server may access the password file. In addition, it is possible to impersonate an authentication server as MD5 authentication method does not perform mutual authentication. Finally, MD5 authentication method does not support data encryption with dynamic session key. You must configure WEP encryption keys for data encryption. EAP-TLS (Transport Layer Security)With EAP-TLS, digital certifications are needed by both the server and the wireless clients for mutual authentication. The server presents a certificate to the client. After validating the identity of the server, the client sends a different certificate to the server. The exchange of certificates is done in the open before a secured tunnel is created. This makes user identity vulnerable to passiveattacks. A digital certificate is an electronic ID card that authenticates the sender’s identity. However, to implement EAP-TLS, you need a Certificate Authority (CA) to handle certificates, which imposes a management overhead.
Appendix D Wireless LANsVMG4380-B10A / VMG4325-B10A User’s Guide334EAP-TTLS (Tunneled Transport Layer Service) EAP-TTLS is an extension of the EAP-TLS authentication that uses certificates for only the server-side authentications to establish a secure connection. Client authentication is then done by sending username and password through the secure connection, thus client identity is protected. For client authentication, EAP-TTLS supports EAP methods and legacy authentication methods such as PAP,CHAP, MS-CHAP and MS-CHAP v2.PEAP (Protected EAP) Like EAP-TTLS, server-side certificate authentication is used to establish a secure connection, then use simple username and password methods through the secured connection to authenticate the clients, thus hiding client identity. However, PEAP only supports EAP methods, such as EAP-MD5, EAP-MSCHAPv2 and EAP-GTC (EAP-Generic Token Card), for client authentication. EAP-GTC is implemented only by Cisco.LEAPLEAP (Lightweight Extensible Authentication Protocol) is a Cisco implementation of IEEE 802.1x. Dynamic WEP Key ExchangeThe AP maps a unique key that is generated with the RADIUS server. This key expires when the wireless connection times out, disconnects or reauthentication times out. A new WEP key is generated each time reauthentication is performed.If this feature is enabled, it is not necessary to configure a default encryption key in the wireless security configuration screen. You may still configure and store keys, but they will not be used whiledynamic WEP is enabled.Note: EAP-MD5 cannot be used with Dynamic WEP Key ExchangeFor added security, certificate-based authentications (EAP-TLS, EAP-TTLS and PEAP) use dynamic keys for data encryption. They are often deployed in corporate environments, but for public deployment, a simple user name and password pair is more practical. The following table is a comparison of the features of authentication types.Table 126 Comparison of EAP Authentication TypesEAP-MD5 EAP-TLS EAP-TTLS PEAP LEAPMutual Authentication No Yes Yes Yes YesCertificate – Client No Yes Optional Optional NoCertificate – Server No Yes Yes Yes NoDynamic Key Exchange No Yes Yes Yes YesCredential Integrity None Strong Strong Strong ModerateDeployment Difficulty Easy Hard Moderate Moderate ModerateClient Identity Protection No No Yes Yes No
Appendix D Wireless LANsVMG4380-B10A / VMG4325-B10A User’s Guide 335WPA and WPA2Wi-Fi Protected Access (WPA) is a subset of the IEEE 802.11i standard. WPA2 (IEEE 802.11i) is a wireless security standard that defines stronger encryption, authentication and key managementthan WPA. Key differences between WPA or WPA2 and WEP are improved data encryption and user authentication.If both an AP and the wireless clients support WPA2 and you have an external RADIUS server, use WPA2 for stronger data encryption. If you don't have an external RADIUS server, you should use WPA2-PSK (WPA2-Pre-Shared Key) that only requires a single (identical) password entered into each access point, wireless gateway and wireless client. As long as the passwords match, a wireless client will be granted access to a WLAN. If the AP or the wireless clients do not support WPA2, just use WPA or WPA-PSK depending onwhether you have an external RADIUS server or not.Select WEP only when the AP and/or wireless clients do not support WPA or WPA2. WEP is less secure than WPA or WPA2.Encryption WPA improves data encryption by using Temporal Key Integrity Protocol (TKIP), Message Integrity Check (MIC) and IEEE 802.1x. WPA2 also uses TKIP when required for compatibility reasons, but offers stronger encryption than TKIP with Advanced Encryption Standard (AES) in the Counter mode with Cipher block chaining Message authentication code Protocol (CCMP).TKIP uses 128-bit keys that are dynamically generated and distributed by the authentication server. AES (Advanced Encryption Standard) is a block cipher that uses a 256-bit mathematical algorithm called Rijndael. They both include a per-packet key mixing function, a Message Integrity Check (MIC) named Michael, an extended initialization vector (IV) with sequencing rules, and a re-keying mechanism.WPA and WPA2 regularly change and rotate the encryption keys so that the same encryption key is never used twice. The RADIUS server distributes a Pairwise Master Key (PMK) key to the AP that then sets up a key hierarchy and management system, using the PMK to dynamically generate unique data encryption keys to encrypt every data packet that is wirelessly communicated between the AP and the wireless clients. This all happens in the background automatically.The Message Integrity Check (MIC) is designed to prevent an attacker from capturing data packets, altering them and resending them. The MIC provides a strong mathematical function in which the receiver and the transmitter each compute and then compare the MIC. If they do not match, it is assumed that the data has been tampered with and the packet is dropped. By generating unique data encryption keys for every data packet and by creating an integrity checking mechanism (MIC), with TKIP and AES it is more difficult to decrypt data on a Wi-Fi network than WEP and difficult for an intruder to break into the network. The encryption mechanisms used for WPA(2) and WPA(2)-PSK are the same. The only differencebetween the two is that WPA(2)-PSK uses a simple common password, instead of user-specific credentials. The common-password approach makes WPA(2)-PSK susceptible to brute-force
Appendix D Wireless LANsVMG4380-B10A / VMG4325-B10A User’s Guide336password-guessing attacks but it’s still an improvement over WEP as it employs a consistent, single, alphanumeric password to derive a PMK which is used to generate unique temporal encryption keys. This prevent all wireless devices sharing the same encryption keys. (a weakness of WEP)User Authentication WPA and WPA2 apply IEEE 802.1x and Extensible Authentication Protocol (EAP) to authenticate wireless clients using an external RADIUS database. WPA2 reduces the number of key exchangemessages from six to four (CCMP 4-way handshake) and shortens the time required to connect to a network. Other WPA2 authentication features that are different from WPA include key caching and pre-authentication. These two features are optional and may not be supported in all wireless devices.Key caching allows a wireless client to store the PMK it derived through a successful authentication with an AP. The wireless client uses the PMK when it tries to connect to the same AP and does not need to go with the authentication process again.Pre-authentication enables fast roaming by allowing the wireless client (already connecting to an AP) to perform IEEE 802.1x authentication with another AP before connecting to it.Wireless Client WPA SupplicantsA wireless client supplicant is the software that runs on an operating system instructing the wireless client how to use WPA. At the time of writing, the most widely available supplicant is the WPA patch for Windows XP, Funk Software's Odyssey client. The Windows XP patch is a free download that adds WPA capability to Windows XP's built-in "Zero Configuration" wireless client. However, you must run Windows XP to use it. WPA(2) with RADIUS Application ExampleTo set up WPA(2), you need the IP address of the RADIUS server, its port number (default is 1812), and the RADIUS shared secret. A WPA(2) application example with an external RADIUS server looks as follows. "A" is the RADIUS server. "DS" is the distribution system.1The AP passes the wireless client's authentication request to the RADIUS server.2The RADIUS server then checks the user's identification against its database and grants or denies network access accordingly.3A 256-bit Pairwise Master Key (PMK) is derived from the authentication process by the RADIUS server and the client.
Appendix D Wireless LANsVMG4380-B10A / VMG4325-B10A User’s Guide 3374The RADIUS server distributes the PMK to the AP. The AP then sets up a key hierarchy and management system, using the PMK to dynamically generate unique data encryption keys. The keys are used to encrypt every data packet that is wirelessly communicated between the AP and the wireless clients.Figure 201 WPA(2) with RADIUS Application ExampleWPA(2)-PSK Application ExampleA WPA(2)-PSK application looks as follows.1First enter identical passwords into the AP and all wireless clients. The Pre-Shared Key (PSK) mustconsist of between 8 and 63 ASCII characters or 64 hexadecimal characters (including spaces and symbols).2The AP checks each wireless client's password and allows it to join the network only if the password matches.3The AP and wireless clients generate a common PMK (Pairwise Master Key). The key itself is not sent over the network, but is derived from the PSK and the SSID. 4The AP and wireless clients use the TKIP or AES encryption process, the PMK and information exchanged in a handshake to create temporal encryption keys. They use these keys to encrypt data exchanged between them.Figure 202 WPA(2)-PSK Authentication
Appendix D Wireless LANsVMG4380-B10A / VMG4325-B10A User’s Guide338Security Parameters SummaryRefer to this table to see what other security parameters you should configure for each authentication method or key management protocol type. MAC address filters are not dependent on how you configure these security features.Antenna OverviewAn antenna couples RF signals onto air. A transmitter within a wireless device sends an RF signal to the antenna, which propagates the signal through the air. The antenna also operates in reverse by capturing RF signals from the air.Positioning the antennas properly increases the range and coverage area of a wireless LAN. Antenna CharacteristicsFrequencyAn antenna in the frequency of 2.4GHz (IEEE 802.11b and IEEE 802.11g) or 5GHz (IEEE 802.11a) is needed to communicate efficiently in a wireless LANRadiation PatternA radiation pattern is a diagram that allows you to visualize the shape of the antenna’s coverage area. Antenna GainAntenna gain, measured in dB (decibel), is the increase in coverage within the RF beam width. Higher antenna gain improves the range of the signal for better communications. For an indoor site, each 1 dB increase in antenna gain results in a range increase of approximately Table 127 Wireless Security Relational MatrixAUTHENTICATION METHOD/ KEY MANAGEMENT PROTOCOLENCRYPTION METHODENTER MANUAL KEY IEEE 802.1XOpen None No DisableEnable without Dynamic WEP KeyOpen WEP No Enable with Dynamic WEP KeyYes Enable without Dynamic WEP KeyYes DisableShared WEP No Enable with Dynamic WEP KeyYes Enable without Dynamic WEP KeyYes DisableWPA TKIP/AES No EnableWPA-PSK TKIP/AES Yes DisableWPA2 TKIP/AES No EnableWPA2-PSK TKIP/AES Yes Disable
Appendix D Wireless LANsVMG4380-B10A / VMG4325-B10A User’s Guide 3392.5%. For an unobstructed outdoor site, each 1dB increase in gain results in a range increase of approximately 5%. Actual results may vary depending on the network environment. Antenna gain is sometimes specified in dBi, which is how much the antenna increases the signal power compared to using an isotropic antenna. An isotropic antenna is a theoretical perfect antenna that sends out radio signals equally well in all directions. dBi represents the true gain that the antenna provides. Types of Antennas for WLANThere are two types of antennas used for wireless LAN applications.• Omni-directional antennas send the RF signal out in all directions on a horizontal plane. The coverage area is torus-shaped (like a donut) which makes these antennas ideal for a room environment. With a wide coverage area, it is possible to make circular overlapping coverage areas with multiple access points. • Directional antennas concentrate the RF signal in a beam, like a flashlight does with the light from its bulb. The angle of the beam determines the width of the coverage pattern. Anglestypically range from 20 degrees (very directional) to 120 degrees (less directional). Directional antennas are ideal for hallways and outdoor point-to-point applications.Positioning AntennasIn general, antennas should be mounted as high as practically possible and free of obstructions. In point-to–point application, position both antennas at the same height and in a direct line of sight to each other to attain the best performance. For omni-directional antennas mounted on a table, desk, and so on, point the antenna up. For omni-directional antennas mounted on a wall or ceiling, point the antenna down. For a single AP application, place omni-directional antennas as close to the center of the coverage area as possible.For directional antennas, point the antenna in the direction of the desired coverage area.
Appendix D Wireless LANsVMG4380-B10A / VMG4325-B10A User’s Guide340
VMG4380-B10A / VMG4325-B10A User’s Guide 341APPENDIX EIPv6OverviewIPv6 (Internet Protocol version 6), is designed to enhance IP address size and features. The increase in IPv6 address size to 128 bits (from the 32-bit IPv4 address) allows up to 3.4 x 1038 IP addresses. IPv6 AddressingThe 128-bit IPv6 address is written as eight 16-bit hexadecimal blocks separated by colons (:). This is an example IPv6 address 2001:0db8:1a2b:0015:0000:0000:1a2f:0000. IPv6 addresses can be abbreviated in two ways:• Leading zeros in a block can be omitted. So 2001:0db8:1a2b:0015:0000:0000:1a2f:0000 can be written as 2001:db8:1a2b:15:0:0:1a2f:0. • Any number of consecutive blocks of zeros can be replaced by a double colon. A double colon can only appear once in an IPv6 address. So 2001:0db8:0000:0000:1a2f:0000:0000:0015 can be written as 2001:0db8::1a2f:0000:0000:0015, 2001:0db8:0000:0000:1a2f::0015, 2001:db8::1a2f:0:0:15 or 2001:db8:0:0:1a2f::15.Prefix and Prefix LengthSimilar to an IPv4 subnet mask, IPv6 uses an address prefix to represent the network address. An IPv6 prefix length specifies how many most significant bits (start from the left) in the address compose the network address. The prefix length is written as “/x” where x is a number. For example,2001:db8:1a2b:15::1a2f:0/32means that the first 32 bits (2001:db8) is the subnet prefix. Link-local AddressA link-local address uniquely identifies a device on the local network (the LAN). It is similar to a “private IP address” in IPv4. You can have the same link-local address on multiple interfaces on a device. A link-local unicast address has a predefined prefix of fe80::/10. The link-local unicast address format is as follows.Table 128 Link-local Unicast Address Format1111 1110 10 0 Interface ID10 bits 54 bits 64 bits
Appendix E IPv6VMG4380-B10A / VMG4325-B10A User’s Guide342Global AddressA global address uniquely identifies a device on the Internet. It is similar to a “public IP address” in IPv4. A global unicast address starts with a 2 or 3. Unspecified AddressAn unspecified address (0:0:0:0:0:0:0:0 or ::) is used as the source address when a device does not have its own address. It is similar to “0.0.0.0” in IPv4.Loopback AddressA loopback address (0:0:0:0:0:0:0:1 or ::1) allows a host to send packets to itself. It is similar to “127.0.0.1” in IPv4.Multicast AddressIn IPv6, multicast addresses provide the same functionality as IPv4 broadcast addresses. Broadcasting is not supported in IPv6. A multicast address allows a host to send packets to all hosts in a multicast group.Multicast scope allows you to determine the size of the multicast group. A multicast address has a predefined prefix of ff00::/8. The following table describes some of the predefined multicast addresses. The following table describes the multicast addresses which are reserved and can not be assigned to a multicast group.Table 129 Predefined Multicast AddressMULTICAST ADDRESS DESCRIPTIONFF01:0:0:0:0:0:0:1 All hosts on a local node. FF01:0:0:0:0:0:0:2 All routers on a local node.FF02:0:0:0:0:0:0:1 All hosts on a local connected link.FF02:0:0:0:0:0:0:2 All routers on a local connected link.FF05:0:0:0:0:0:0:2 All routers on a local site. FF05:0:0:0:0:0:1:3 All DHCP severs on a local site. Table 130 Reserved Multicast AddressMULTICAST ADDRESSFF00:0:0:0:0:0:0:0FF01:0:0:0:0:0:0:0FF02:0:0:0:0:0:0:0FF03:0:0:0:0:0:0:0FF04:0:0:0:0:0:0:0FF05:0:0:0:0:0:0:0FF06:0:0:0:0:0:0:0FF07:0:0:0:0:0:0:0
Appendix E IPv6VMG4380-B10A / VMG4325-B10A User’s Guide 343Subnet MaskingBoth an IPv6 address and IPv6 subnet mask compose of 128-bit binary digits, which are dividedinto eight 16-bit blocks and written in hexadecimal notation. Hexadecimal uses four bits for eachcharacter (1 ~ 10, A ~ F). Each block’s 16 bits are then represented by four hexadecimal characters. For example, FFFF:FFFF:FFFF:FFFF:FC00:0000:0000:0000.Interface IDIn IPv6, an interface ID is a 64-bit identifier. It identifies a physical interface (for example, an Ethernet port) or a virtual interface (for example, the management IP address for a VLAN). One interface should have a unique interface ID.EUI-64The EUI-64 (Extended Unique Identifier) defined by the IEEE (Institute of Electrical and Electronics Engineers) is an interface ID format designed to adapt with IPv6. It is derived from the 48-bit (6-byte) Ethernet MAC address as shown next. EUI-64 inserts the hex digits fffe between the third and fourth bytes of the MAC address and complements the seventh bit of the first byte of the MAC address. See the following example.Identity AssociationAn Identity Association (IA) is a collection of addresses assigned to a DHCP client, through which the server and client can manage a set of related IP addresses. Each IA must be associated withexactly one interface. The DHCP client uses the IA assigned to an interface to obtain configurationfrom a DHCP server for that interface. Each IA consists of a unique IAID and associated IP information.The IA type is the type of address in the IA. Each IA holds one type of address. IA_NA means anidentity association for non-temporary addresses and IA_TA is an identity association for temporary addresses. An IA_NA option contains the T1 and T2 fields, but an IA_TA option does not. The DHCPv6 server uses T1 and T2 to control the time at which the client contacts with the server to extend the lifetimes on any addresses in the IA_NA before the lifetimes expire. After T1, the client sends the server (S1) (from which the addresses in the IA_NA were obtained) a Renew message. If FF08:0:0:0:0:0:0:0FF09:0:0:0:0:0:0:0FF0A:0:0:0:0:0:0:0FF0B:0:0:0:0:0:0:0FF0C:0:0:0:0:0:0:0FF0D:0:0:0:0:0:0:0FF0E:0:0:0:0:0:0:0FF0F:0:0:0:0:0:0:0Table 130 Reserved Multicast Address (continued)MULTICAST ADDRESS MAC 00 : 13 : 49 : 12 : 34 : 56 EUI-64 02: 13 : 49 : FF : FE : 12 : 34 : 56
Appendix E IPv6VMG4380-B10A / VMG4325-B10A User’s Guide344the time T2 is reached and the server does not respond, the client sends a Rebind message to any available server (S2). For an IA_TA, the client may send a Renew or Rebind message at the client'sdiscretion.DHCP Relay AgentA DHCP relay agent is on the same network as the DHCP clients and helps forward messages between the DHCP server and clients. When a client cannot use its link-local address and a well-known multicast address to locate a DHCP server on its network, it then needs a DHCP relay agent to send a message to a DHCP server that is not attached to the same network.The DHCP relay agent can add the remote identification (remote-ID) option and the interface-ID option to the Relay-Forward DHCPv6 messages. The remote-ID option carries a user-defined string, such as the system name. The interface-ID option provides slot number, port information and theVLAN ID to the DHCPv6 server. The remote-ID option (if any) is stripped from the Relay-Reply messages before the relay agent sends the packets to the clients. The DHCP server copies theinterface-ID option from the Relay-Forward message into the Relay-Reply message and sends it to the relay agent. The interface-ID should not change even after the relay agent restarts.Prefix DelegationPrefix delegation enables an IPv6 router to use the IPv6 prefix (network address) received from the ISP (or a connected uplink router) for its LAN. The Device uses the received IPv6 prefix (for example, 2001:db2::/48) to generate its LAN IP address. Through sending Router Advertisements (RAs) regularly by multicast, the Device passes the IPv6 prefix information to its LAN hosts. Thehosts then can use the prefix to generate their IPv6 addresses.ICMPv6Internet Control Message Protocol for IPv6 (ICMPv6 or ICMP for IPv6) is defined in RFC 4443. ICMPv6 has a preceding Next Header value of 58, which is different from the value used to identify ICMP for IPv4. ICMPv6 is an integral part of IPv6. IPv6 nodes use ICMPv6 to report errors encountered in packet processing and perform other diagnostic functions, such as "ping".Neighbor Discovery Protocol (NDP)The Neighbor Discovery Protocol (NDP) is a protocol used to discover other IPv6 devices and track neighbor’s reachability in a network. An IPv6 device uses the following ICMPv6 messages types: • Neighbor solicitation: A request from a host to determine a neighbor’s link-layer address (MAC address) and detect if the neighbor is still reachable. A neighbor being “reachable” means it responds to a neighbor solicitation message (from the host) with a neighbor advertisement message. T1T2Renew RebindRebindto S1Renewto S1Renewto S1Renewto S1Renewto S1Renewto S1to S2to S2
Appendix E IPv6VMG4380-B10A / VMG4325-B10A User’s Guide 345• Neighbor advertisement: A response from a node to announce its link-layer address.• Router solicitation: A request from a host to locate a router that can act as the default router and forward packets.• Router advertisement: A response to a router solicitation or a periodical multicast advertisement from a router to advertise its presence and other parameters.IPv6 CacheAn IPv6 host is required to have a neighbor cache, destination cache, prefix list and default router list. The Device maintains and updates its IPv6 caches constantly using the information from response messages. In IPv6, the Device configures a link-local address automatically, and then sends a neighbor solicitation message to check if the address is unique. If there is an address to be resolved or verified, the Device also sends out a neighbor solicitation message. When the Devicereceives a neighbor advertisement in response, it stores the neighbor’s link-layer address in the neighbor cache. When the Device uses a router solicitation message to query for a router and receives a router advertisement message, it adds the router’s information to the neighbor cache, prefix list and destination cache. The Device creates an entry in the default router list cache if therouter can be used as a default router.When the Device needs to send a packet, it first consults the destination cache to determine the next hop. If there is no matching entry in the destination cache, the Device uses the prefix list to determine whether the destination address is on-link and can be reached directly without passing through a router. If the address is unlink, the address is considered as the next hop. Otherwise, the Device determines the next-hop from the default router list or routing table. Once the next hop IP address is known, the Device looks into the neighbor cache to get the link-layer address and sends the packet when the neighbor is reachable. If the Device cannot find an entry in the neighbor cache or the state for the neighbor is not reachable, it starts the address resolution process. This helps reduce the number of IPv6 solicitation and advertisement messages.Multicast Listener DiscoveryThe Multicast Listener Discovery (MLD) protocol (defined in RFC 2710) is derived from IPv4's Internet Group Management Protocol version 2 (IGMPv2). MLD uses ICMPv6 message types, rather than IGMP message types. MLDv1 is equivalent to IGMPv2 and MLDv2 is equivalent to IGMPv3.MLD allows an IPv6 switch or router to discover the presence of MLD listeners who wish to receive multicast packets and the IP addresses of multicast groups the hosts want to join on its network. MLD snooping and MLD proxy are analogous to IGMP snooping and IGMP proxy in IPv4.MLD filtering controls which multicast groups a port can join.MLD MessagesA multicast router or switch periodically sends general queries to MLD hosts to update the multicast forwarding table. When an MLD host wants to join a multicast group, it sends an MLD Report message for that address.An MLD Done message is equivalent to an IGMP Leave message. When an MLD host wants to leavea multicast group, it can send a Done message to the router or switch. The router or switch then sends a group-specific query to the port on which the Done message is received to determine if other devices connected to this port should remain in the group.
Appendix E IPv6VMG4380-B10A / VMG4325-B10A User’s Guide346Example - Enabling IPv6 on Windows XP/2003/VistaBy default, Windows XP and Windows 2003 support IPv6. This example shows you how to use the ipv6 install command on Windows XP/2003 to enable IPv6. This also displays how to use the ipconfig command to see auto-generated IP addresses.IPv6 is installed and enabled by default in Windows Vista. Use the ipconfig command to check your automatic configured IPv6 address as well. You should see at least one IPv6 address available for the interface on your computer.Example - Enabling DHCPv6 on Windows XPWindows XP does not support DHCPv6. If your network uses DHCPv6 for IP address assignment, you have to additionally install a DHCPv6 client software on your Windows XP. (Note: If you use static IP addresses or Router Advertisement for IPv6 address assignment in your network, ignore this section.)This example uses Dibbler as the DHCPv6 client. To enable DHCPv6 client on your computer:1Install Dibbler and select the DHCPv6 client option on your computer.2After the installation is complete, select Start > All Programs > Dibbler-DHCPv6 > Client Install as service.3Select Start > Control Panel > Administrative Tools > Services.C:\>ipv6 installInstalling...Succeeded.C:\>ipconfigWindows IP ConfigurationEthernet adapter Local Area Connection: Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 10.1.1.46 Subnet Mask . . . . . . . . . . . : 255.255.255.0 IP Address. . . . . . . . . . . . : fe80::2d0:59ff:feb8:103c%4 Default Gateway . . . . . . . . . : 10.1.1.254
Appendix E IPv6VMG4380-B10A / VMG4325-B10A User’s Guide 3474Double click Dibbler - a DHCPv6 client.5Click Start and then OK.6Now your computer can obtain an IPv6 address from a DHCPv6 server.Example - Enabling IPv6 on Windows 7Windows 7 supports IPv6 by default. DHCPv6 is also enabled when you enable IPv6 on a Windows 7 computer.To enable IPv6 in Windows 7:1Select Control Panel > Network and Sharing Center > Local Area Connection.2Select the Internet Protocol Version 6 (TCP/IPv6) checkbox to enable it.3Click OK to save the change.
Appendix E IPv6VMG4380-B10A / VMG4325-B10A User’s Guide3484Click Close to exit the Local Area Connection Status screen.5Select Start > All Programs > Accessories > Command Prompt.6Use the ipconfig command to check your dynamic IPv6 address. This example shows a global address (2001:b021:2d::1000) obtained from a DHCP server.C:\>ipconfigWindows IP ConfigurationEthernet adapter Local Area Connection: Connection-specific DNS Suffix . : IPv6 Address. . . . . . . . . . . : 2001:b021:2d::1000 Link-local IPv6 Address . . . . . : fe80::25d8:dcab:c80a:5189%11 IPv4 Address. . . . . . . . . . . : 172.16.100.61 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : fe80::213:49ff:feaa:7125%11 172.16.100.254
VMG4380-B10A / VMG4325-B10A User’s Guide 349APPENDIX FServicesThe following table lists some commonly-used services and their associated protocols and port numbers.•Name: This is a short, descriptive name for the service. You can use this one or create a different one, if you like.•Protocol: This is the type of IP protocol used by the service. If this is TCP/UDP, then the service uses the same port number with TCP and UDP. If this is USER-DEFINED, the Port(s) is the IP protocol number, not the port number.•Port(s): This value depends on the Protocol.• If the Protocol is TCP, UDP, or TCP/UDP, this is the IP port number.• If the Protocol is USER, this is the IP protocol number.•Description: This is a brief explanation of the applications that use this service or the situationsin which this service is used.
Appendix F ServicesVMG4380-B10A / VMG4325-B10A User’s Guide350Table 131 Examples of ServicesNAME PROTOCOL PORT(S) DESCRIPTIONAH (IPSEC_TUNNEL) User-Defined 51 The IPSEC AH (Authentication Header) tunneling protocol uses this service.AIM TCP 5190 AOL’s Internet Messenger service.AUTH TCP 113 Authentication protocol used by some servers.BGP TCP 179 Border Gateway Protocol.BOOTP_CLIENT UDP 68 DHCP Client.BOOTP_SERVER UDP 67 DHCP Server.CU-SEEME TCP/UDPTCP/UDP764824032A popular videoconferencing solution from White Pines Software.DNS TCP/UDP 53 Domain Name Server, a service thatmatches web names (for instancewww.zyxel.com) to IP numbers.ESP(IPSEC_TUNNEL)User-Defined 50 The IPSEC ESP (Encapsulation SecurityProtocol) tunneling protocol uses thisservice.FINGER TCP 79 Finger is a UNIX or Internet related command that can be used to find out if a user is logged on.FTP TCPTCP2021File Transfer Protocol, a program to enablefast transfer of files, including large files that may not be possible by e-mail.H.323 TCP 1720 NetMeeting uses this protocol.HTTP TCP 80 Hyper Text Transfer Protocol - a client/server protocol for the world wide web.HTTPS TCP 443 HTTPS is a secured http session often used in e-commerce.ICMP User-Defined 1 Internet Control Message Protocol is often used for diagnostic purposes.ICQ UDP 4000 This is a popular Internet chat program.IGMP (MULTICAST) User-Defined 2 Internet Group Multicast Protocol is used when sending packets to a specific group of hosts.IKE UDP 500 The Internet Key Exchange algorithm is used for key distribution and management.IMAP4 TCP 143 The Internet Message Access Protocol isused for e-mail.IMAP4S TCP 993 This is a more secure version of IMAP4 thatruns over SSL.IRC TCP/UDP 6667 This is another popular Internet chat program.MSN Messenger TCP 1863 Microsoft Networks’ messenger service uses this protocol. NetBIOS TCP/UDPTCP/UDPTCP/UDPTCP/UDP137138139445The Network Basic Input/Output System isused for communication between computers in a LAN.
Appendix F ServicesVMG4380-B10A / VMG4325-B10A User’s Guide 351NEW-ICQ TCP 5190 An Internet chat program.NEWS TCP 144 A protocol for news groups.NFS UDP 2049 Network File System - NFS is a client/server distributed file service that providestransparent file sharing for network environments.NNTP TCP 119 Network News Transport Protocol is the delivery mechanism for the USENET newsgroup service.PING User-Defined 1 Packet INternet Groper is a protocol that sends out ICMP echo requests to test whether or not a remote host is reachable.POP3 TCP 110 Post Office Protocol version 3 lets a client computer get e-mail from a POP3 server through a temporary connection (TCP/IP or other).POP3S TCP 995 This is a more secure version of POP3 that runs over SSL.PPTP TCP 1723 Point-to-Point Tunneling Protocol enables secure transfer of data over public networks. This is the control channel.PPTP_TUNNEL (GRE) User-Defined 47 PPTP (Point-to-Point Tunneling Protocol) enables secure transfer of data over publicnetworks. This is the data channel.RCMD TCP 512 Remote Command Service.REAL_AUDIO TCP 7070 A streaming audio service that enables real time sound over the web.REXEC TCP 514 Remote Execution Daemon.RLOGIN TCP 513 Remote Login.ROADRUNNER TCP/UDP 1026 This is an ISP that provides services mainly for cable modems.RTELNET TCP 107 Remote Telnet.RTSP TCP/UDP 554 The Real Time Streaming (media control)Protocol (RTSP) is a remote control formultimedia on the Internet. SFTP TCP 115 The Simple File Transfer Protocol is an old way of transferring files between computers.SMTP TCP 25 Simple Mail Transfer Protocol is the message-exchange standard for the Internet. SMTP enables you to move messages from one e-mail server toanother.SMTPS TCP 465 This is a more secure version of SMTP thatruns over SSL.SNMP TCP/UDP 161 Simple Network Management Program.SNMP-TRAPS TCP/UDP 162 Traps for use with the SNMP (RFC:1215).Table 131 Examples of Services (continued)NAME PROTOCOL PORT(S) DESCRIPTION
Appendix F ServicesVMG4380-B10A / VMG4325-B10A User’s Guide352SQL-NET TCP 1521 Structured Query Language is an interface to access data on many different types of database systems, including mainframes,midrange systems, UNIX systems and network servers.SSDP UDP 1900 The Simple Service Discovery Protocolsupports Universal Plug-and-Play (UPnP).SSH TCP/UDP 22 Secure Shell Remote Login Program.STRM WORKS UDP 1558 Stream Works Protocol.SYSLOG UDP 514 Syslog allows you to send system logs to aUNIX server.TACACS UDP 49 Login Host Protocol used for (Terminal Access Controller Access Control System).TELNET TCP 23 Telnet is the login and terminal emulation protocol common on the Internet and in UNIX environments. It operates over TCP/IP networks. Its primary function is to allow users to log into remote host systems.VDOLIVE TCPUDP7000user-definedA videoconferencing solution. The UDP portnumber is specified in the application.Table 131 Examples of Services (continued)NAME PROTOCOL PORT(S) DESCRIPTION
VMG4380-B10A / VMG4325-B10A User’s Guide 353APPENDIX GLegal InformationCopyrightCopyright © 2012 by MitraStar Communications Corporation.The contents of this publication may not be reproduced in any part or as a whole, transcribed, stored in a retrieval system, translated into any language, or transmitted in any form or by any means, electronic, mechanical, magnetic, optical, chemical, photocopying, manual, or otherwise, without the prior written permission of ZyXEL Communications Corporation.Published by MitraStar Communications Corporation. All rights reserved.DisclaimerMitraStar does not assume any liability arising out of the application or use of any products, or software described herein. Neither does it convey any license under its patent rights nor the patent rights of others. ZyXEL further reserves the right to make changes in any products described herein without notice. This publication is subject to change without notice.Certifications Federal Communications Commission (FCC) Interference StatementThe device complies with Part 15 of FCC rules. Operation is subject to the following two conditions:• This device may not cause harmful interference.• This device must accept any interference received, including interference that may cause undesired operations.This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.If this device does cause harmful interference to radio/television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures:1Reorient or relocate the receiving antenna.2Increase the separation between the equipment and the receiver.
Appendix G Legal InformationVMG4380-B10A / VMG4325-B10A User’s Guide3543Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.4Consult the dealer or an experienced radio/TV technician for help.FCC Radiation Exposure Statement• This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.• IEEE 802.11b/g/n(HT20) operation of this product in the U.S.A.is firmware-limited to channels1 through 11. In 11n(HT40) mode, it is firmware-limited to channels 3 throug 9. • To comply with FCC RF exposure compliance requirements, a separation distance of at least 20cm must be maintained between the antenna of this device and all persons.注意 !依據 低功率電波輻射性電機管理辦法第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信規定作業之無線電信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。本機限在不干擾合法電臺與不受被干擾保障條件下於室內使用。減少電磁波影響，請妥適使用。Notices Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.This device has been designed for the WLAN 2.4 GHz network throughout the EC region and Switzerland, with restrictions in France. Ce produit est conçu pour les bandes de fréquences 2,4 GHz et/ou 5 GHz conformément à la législation Européenne. En France métropolitaine, suivant les décisions n°03-908 et 03-909 de l’ARCEP, la puissance d’émission ne devra pas dépasser 10 mW (10 dB) dans le cadre d’uneinstallation WiFi en extérieur pour les fréquences comprises entre 2454 MHz et 2483,5 MHz.This Class [*] digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la classe [*] est conforme à la norme NMB-003 du Canada.MitraStar Limited WarrantyMitraStar warrants to the original end user (purchaser) that this product is free from any defects in materials or workmanship for a period of up to two years from the date of purchase. During the CAUTION:
Appendix G Legal InformationVMG4380-B10A / VMG4325-B10A User’s Guide 355warranty period, and upon proof of purchase, should the product have indications of failure due to faulty workmanship and/or materials, MitraStar will, at its discretion, repair or replace the defective products or components without charge for either parts or labor, and to whatever extent it shall deem necessary to restore the product or components to proper operating condition. Any replacement will consist of a new or re-manufactured functionally equivalent product of equal or higher value, and will be solely at the discretion of MitraStar. This warranty shall not apply if the product has been modified, misused, tampered with, damaged by an act of God, or subjected to abnormal working conditions.NoteRepair or replacement, as provided under this warranty, is the exclusive remedy of the purchaser.This warranty is in lieu of all other warranties, express or implied, including any implied warranty of merchantability or fitness for a particular use or purpose. MitraStar shall in no event be held liable for indirect or consequential damages of any kind to the purchaser.To obtain the services of this warranty, contact MitraStar's Service Center for your Return Material Authorization number (RMA). Products must be returned Postage Prepaid. It is recommended that the unit be insured when shipped. Any returned products without proof of purchase or those withan out-dated warranty will be repaired or replaced (at the discretion of MitraStar) and the customer will be billed for parts and labor. All repaired or replaced products will be shipped by MitraStar to the corresponding return address, Postage Paid. This warranty gives you specific legal rights, and you may also have other rights that vary from country to country.RegistrationRegister your product online to receive e-mail notices of firmware upgrades and information at www.zyxel.com for global products, or at www.us.zyxel.com for North American products.Safety Warnings• Do NOT use this product near water, for example, in a wet basement or near a swimming pool.• Do NOT expose your device to dampness, dust or corrosive liquids.• Do NOT store things on the device.• Do NOT install, use, or service this device during a thunderstorm. There is a remote risk of electric shock from lightning.• Connect ONLY suitable accessories to the device.• Do NOT open the device or unit. Opening or removing covers can expose you to dangerous high voltage points or other risks. ONLY qualified service personnel should service or disassemble this device. Please contact your vendor for further information.• Make sure to connect the cables to the correct ports.• Place connecting cables carefully so that no one will step on them or stumble over them.• Always disconnect all cables from this device before servicing or disassembling.• Use ONLY an appropriate power adaptor or cord for your device.• Connect the power adaptor or cord to the right supply voltage (for example, 110V AC in North America or 230V AC in Europe).• Do NOT allow anything to rest on the power adaptor or cord and do NOT place the product where anyone canwalk on the power adaptor or cord.• Do NOT use the device if the power adaptor or cord is damaged as it might cause electrocution.• If the power adaptor or cord is damaged, remove it from the device and the power source.• Do NOT attempt to repair the power adaptor or cord. Contact your local vendor to order a new one.• Do not use the device outside, and make sure all the connections are indoors. There is a remote risk of electric shock from lightning. • Do NOT obstruct the device ventilation slots, as insufficient airflow may harm your device. • Use only No. 26 AWG (American Wire Gauge) or larger telecommunication line cord.
Appendix G Legal InformationVMG4380-B10A / VMG4325-B10A User’s Guide356• Antenna Warning! This device meets ETSI and FCC certification requirements when using the included antenna(s). Only use the included antenna(s). • This product is for indoor use only (utilisation intérieure exclusivement). •The screen of the coaxial cable is intended to be connected to earth in the building installation.Your product is marked with this symbol, which is known as the WEEE mark. WEEE stands for Waste Electronics and Electrical Equipment. It means that used electrical and electronic products should not be mixed with general waste. Used electrical and electronic equipment should be treated separately.
IndexVMG4380-B10A / VMG4325-B10A User’s Guide 357IndexAACL rule 215ACS 257activationfirewalls 211media server 207SIP ALG 186SSID 108adding a printer example 63Address Resolution Protocol 243administrator password 26alternative subnet mask notation 312antennadirectional 339gain 338omni-directional 339AP (access point) 329applicationsInternet access 18media server 206activation 207iTunes server 206applications, NAT 191ARP Table 243, 245authentication 119, 120RADIUS server 120Auto Configuration Server, see ACS 257Bbackupconfiguration 273Basic Service Set, See BSS 327Basic Service Set, see BSSblinking LEDs 21Broadband 75broadcast 97BSS 122, 327example 122CCA 227, 333Canonical Format Indicator See CFICCMs 276certificatefactory default 228Certificate AuthoritySee CA.certificates 227authentication 227CAcreating 229public key 227replacing 228storage space 228Certification Authority 227Certification Authority. see CAcertifications 353notices 354CFI 97CFM 276CCMs 276link trace test 276loopback test 276MA 276MD 276MEP 276MIP 276channel 329interference 329channel, wireless LAN 118client list 136compatibility, WDS 113configurationbackup 273firewalls 211reset 275
VMG4380-B10A / VMG4325-B10A User’s Guide358Indexrestoring 274static route 93, 155, 195Connectivity Check Messages, see CCMscopyright 353CoS 172CoS technologies 160creating certificates 229CTS (Clear to Send) 330CTS threshold 115, 119Ddata fragment threshold 115, 119DDoS 210default server address 185Denials of Service, see DoSDHCP 132, 150Differentiated Services, see DiffServ 172DiffServ 172marking rule 173digital IDs 227disclaimer 353DLNA 206DMZ 185DNS 132, 151DNS server address assignment 97Domain Name 191Domain Name System, see DNSDomain Name System. See DNS.DoS 210DS field 172DS, dee differentiated servicesDSCP 172dynamic DNS 193wildcard 194Dynamic Host Configuration Protocol, see DHCPdynamic WEP key exchange 334DYNDNS wildcard 194EEAP Authentication 333ECHO 191e-maillog example 268Encapsulation 93MER 94PPP over Ethernet 94encapsulation 76RFC 1483 94encryption 121, 335ESS 328Extended Service Set IDentification 102, 109Extended Service Set, See ESS 328FFCC interference statement 353File Sharing 204file sharing 20filtersMAC address 109, 120Finger 191firewalls 209add protocols 211configuration 211DDoS 210DoS 210LAND attack 210Ping of Death 210SYN attack 210firmware 271version 73forwarding ports 178fragmentation threshold 115, 119, 330FTP 178, 191GGeneral wireless LAN screen 100
IndexVMG4380-B10A / VMG4325-B10A User’s Guide 359Hhidden node 329HTTP 191IIANA 316Internet Assigned Numbers Authoritysee IANAIBSS 327IEEE 802.11g 331IEEE 802.1Q 97IGA 189IGMP 97multicast group list 247version 97ILA 189Independent Basic Service SetSee IBSS 327initialization vector (IV) 335Inside Global Address, see IGAInside Local Address, see ILAinterface group 197Internetwizard setup 33Internet access 18wizard setup 33Internet Protocol version 6 77Internet Protocol version 6, see IPv6Internet Service Provider, see ISPIP address 132, 151ping 277private 152WAN 76IP Address Assignment 96IP aliasNAT applications 191IPv6 77, 341addressing 77, 98, 341EUI-64 343global address 342interface ID 343link-local address 341Neighbor Discovery Protocol 341ping 341prefix 77, 98, 341prefix delegation 78prefix length 77, 98, 341unspecified address 342ISP 76iTunes server 206LLAN 131client list 136DHCP 132, 150DNS 132, 151IP address 132, 133, 151MAC address 137status 73subnet mask 132, 133, 151LAND attack 210LAN-Side DSL CPE Configuration 259LBR 276limitationswireless LAN 121WPS 129link trace 276Link Trace Message, see LTMLink Trace Response, see LTRlogin 25passwords 26logs 235, 239, 247, 267Loop Back Response, see LBRloopback 276LTM 276LTR 276MMA 276MAC address 110, 137filter 109, 120MAC authentication 109Mac filter 219
VMG4380-B10A / VMG4325-B10A User’s Guide360IndexMaintenance Association, see MAMaintenance Domain, see MDMaintenance End Point, see MEPmanaging the devicegood habits 17Maximum Burst Size (MBS) 95MBSSID 122MD 276media server 206activation 207iTunes server 206MEP 276MTU (Multi-Tenant Unit) 96multicast 97Multiple BSS, see MBSSIDmultiplexing 94LLC-based 95VC-based 94multiprotocol encapsulation 94NNAT 177, 179, 188, 189, 316applications 191IP alias 191example 190global 189IGA 189ILA 189inside 189local 189outside 189port forwarding 178port number 191services 191SIP ALG 186activation 186NAT example 192Network Address Translationsee NATNetwork Address Translation, see NATNetwork Map 71network map 29NNTP 191PPairwise Master Key (PMK) 335, 337passwords 26PBC 124Peak Cell Rate (PCR) 95Per-Hop Behavior, see PHB 173PHB 173PIN, WPS 124example 126Ping of Death 210Point-to-Point Tunneling Protocol 191POP3 191port forwarding 178ports 21PPP over Ethernet, see PPPoEPPPoE 76, 94Benefits 94PPTP 191preamble 116, 119preamble mode 123prefix delegation 78Printer Server 207printer sharing 62configuration 62requirements 207private IP address 152product registration 355protocol 76PSK 335push button 23Push Button Configuration, see PBCpush button, WPS 124QQoS 159, 172marking 160setup 159tagging 160versus CoS 160Quality of Service, see QoS
IndexVMG4380-B10A / VMG4325-B10A User’s Guide 361RRADIUS 332message types 332messages 332shared secret key 333RADIUS server 120registrationproduct 355related documentation 2remote managementTR-069 257Remote Procedure Calls, see RPCs 257reset 22, 275restart 275restoring configuration 274RFC 1058. See RIP.RFC 1389. See RIP.RFC 1483 94RFC 3164 235RIP 157router features 18Routing Information Protocol. See RIPRPPCs 257RTS (Request To Send) 330threshold 329, 330RTS threshold 115, 119Ssecuritywireless LAN 119Security Log 237Security Parameter Index, see SPIservice access control 255Service Set 102, 109Services 191setupfirewalls 211static route 93, 155, 195Single Rate Three Color Marker, see srTCMSIP ALG 186activation 186SMTP 191SNMP 191SNMP trap 191SPI 210srTCM 174SSID 120activation 108MBSSID 122static route 153, 265configuration 93, 155, 195example 153static VLANstatus 71firmware version 73LAN 73WAN 73wireless LAN 73status indicators 21subnet 309subnet mask 132, 151, 310subnetting 312Sustained Cell Rate (SCR) 95SYN attack 210syslogprotocol 235severity levels 235systemfirmware 271version 73passwords 26reset 22status 71LAN 73WAN 73wireless LAN 73time 261TTag Control Information See TCITag Protocol Identifier See TPIDTCIThe 76thresholdsdata fragment 115, 119
VMG4380-B10A / VMG4325-B10A User’s Guide362IndexRTS/CTS 115, 119time 261TPID 97TR-064 259TR-069 257ACS setup 257authentication 258traffic shaping 95trTCM 175Two Rate Three Color Marker, see trTCMUunicast 97Universal Plug and Play, see UPnPupgrading firmware 271UPnP 138cautions 133example 139installation 139NAT traversal 132USB features 20VVIDVirtual Circuit (VC) 94Virtual Local Area Network See VLANVLAN 96Introduction 96number of possible VIDspriority framestaticVLAN ID 97VLAN Identifier See VIDVLAN tag 97WWANstatus 73Wide Area Network, see WAN 75warrantynote 355WDS 113, 123compatibility 113example 123web configurator 25login 25passwords 26WEP 121WEP Encryption 104, 105WEP encryption 103WEP key 103Wi-Fi Protected Access 335wireless client WPA supplicants 336Wireless Distribution System, see WDSwireless LAN 99, 117authentication 119, 120BSS 122example 122channel 118encryption 121example 118fragmentation threshold 115, 119limitations 121MAC address filter 109, 120MBSSID 122preamble 116, 119RADIUS server 120RTS/CTS threshold 115, 119security 119SSID 120activation 108status 73WDS 113, 123compatibility 113example 123WEP 121WPA 121WPA-PSK 121WPS 123, 126example 127limitations 129PIN 124push button 23, 124wireless security 331Wireless tutorial 40wizard setupInternet 33
IndexVMG4380-B10A / VMG4325-B10A User’s Guide 363WLANinterference 329security parameters 338WPA 121, 335key caching 336pre-authentication 336user authentication 336vs WPA-PSK 335wireless client supplicant 336with RADIUS application example 336WPA2 335user authentication 336vs WPA2-PSK 335wireless client supplicant 336with RADIUS application example 336WPA2-Pre-Shared Key 335WPA2-PSK 335application example 337WPA-PSK 121, 335application example 337WPS 123, 126example 127limitations 129PIN 124example 126push button 23, 124
VMG4380-B10A / VMG4325-B10A User’s Guide364Index
IndexVMG4380-B10A / VMG4325-B10A User’s Guide 365
VMG4380-B10A / VMG4325-B10A User’s Guide366Index

Navigation menu