dormakaba Canada 515123 ZigBee GEN2 User Manual Q8S 515123UserMan1x

dormakaba Canada Inc. ZigBee GEN2 Q8S 515123UserMan1x

User Manual

Download: dormakaba Canada 515123 ZigBee GEN2 User Manual Q8S 515123UserMan1x
Mirror Download [FCC.gov]dormakaba Canada 515123 ZigBee GEN2 User Manual Q8S 515123UserMan1x
Document ID3864271
Application IDhdENyqqiLA2sqj9pjN9Udg==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize160.47kB (2005838 bits)
Date Submitted2018-05-25 00:00:00
Date Available2018-05-25 00:00:00
Creation Date2018-05-17 13:12:56
Producing SoftwareGPL Ghostscript 9.06
Document Lastmod2018-05-17 13:12:56
Document TitleMicrosoft Word - Q8S-515123UserMan1.docx
Document CreatorPScript5.dll Version 5.2.2
Document Author: moscami

Document No.
ZigBee Gen 2 Module Installation
Revision:
Guide
Prepared by: Michael Mosca
Date: 05/09/2018
ZigBee Gen 2 Module Installation Guide
Q8S-515123UserMan1.docx
of 7
Document No.
Revision:
ZigBee Gen 2 Module Installation
Guide
Prepared by: Michael Mosca
Date: 05/09/2018
REVISION HISTORY
Rev.
Date
11/14/2017
11/20/17
12/21/17
04/16/2018
5/01/2018
5/09/2018
Description
Release of document
Photo on page 3 changed to
correct PCB
Made by
Checked
MM
GC
MM
GC
Update FCC-IC Statements
MM
Update FCC-IC label
LH
Update Installation of FCCIC label on inside trim
Correction of FCC / IC label
for Zigbee internal installation
Approved
LH
LH
Clarification of instructions
5/14/2018
for host user to provide
accurate documentation
LH
required
TABLE OF CONTENTS
1.
INSTALL DOUBLE DECKER END CAP .................................................................................................................................... 3
2.
LABEL UPGRADES AND ADDITIONS ...................................................................................................................................... 6
2 of 7
Document No.
Revision:
ZigBee Gen 2 Module Installation
Guide
Prepared by: Michael Mosca
Date: 05/09/2018
1. Install Double Decker End Cap
Install the communication boards as shown.
RF board is in the upper position.
Ensure the wires run through the notch in
the cap so they do not become pinched
when the cap is installed on the chassis.
3 of 7
Document No.
Revision:
ZigBee Gen 2 Module Installation
Guide
Prepared by: Michael Mosca
Date: 05/09/2018
4 of 7
Document No.
Revision:
ZigBee Gen 2 Module Installation
Guide
Prepared by: Michael Mosca
Date: 05/09/2018
Install the end cap onto the chassis by pressing it
over the screw post as shown.
Connect the ZigBee module
wire harness to the MT4
PCB as shown.
Ensure all wires are
connected and routed
properly and will not be
pinched when the cover is
reinstalled.
ZigBee Connection
5 of 7
Document No.
Revision:
ZigBee Gen 2 Module Installation
Guide
Prepared by: Michael Mosca
Date: 05/09/2018
2. Label Upgrades and Additions
Ensure the “DEAD BOLT CAM POSITION”
label is replaced with the latest MT4 version.
Part Number: A37780
Ensure the Certification label is applied on the
inside cover of the lock.
Part Number: 038-516218
Note: Part displayed is the inside cover
Reinstall the escutcheon and tighten the screws
with a tamper resistant T20 bit.
6 of 7
Document No.
Revision:
ZigBee Gen 2 Module Installation
Guide
Prepared by: Michael Mosca
Date: 05/09/2018
Hosts integrating this module must show the IDs information, i.e. Contains FCC ID Q8S515123, Contains IC: 4652A515123 and provide the following warnings in their documentation;
1)
FCC Interference Statement (Part 15.105 (b))
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
2)
ISED RSS-Gen Notice:
“Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux conditions suivantes :
1) l’appareil ne doit pas produire de brouillage;
2) l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.”
This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions;
1) This device may not cause harmful interference.
2) This device must accept any interference received including interference that may cause undesired operation.
3)
FCC/ISEDC RF Exposure Guidance Statement:
“Afin de se conformer aux exigences d'exposition RF FCC / ISED, cet appareil doit être installé pour fournir au
moins 20 cm de séparation du corps humain en tout temps.“
In order to comply with the requirements of the RF FCC / ISED, this device must be installed to provide at least
20 cm of separation from the human body at all times.
7 of 7

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 7
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:0a71666b-5c51-11e8-0000-a6012b287796
Producer                        : GPL Ghostscript 9.06
Modify Date                     : 2018:05:17 13:12:56-04:00
Create Date                     : 2018:05:17 13:12:56-04:00
Creator Tool                    : PScript5.dll Version 5.2.2
Document ID                     : uuid:0a71666b-5c51-11e8-0000-a6012b287796
Format                          : application/pdf
Title                           : Microsoft Word - Q8S-515123UserMan1.docx
Creator                         : moscami
Author                          : moscami
EXIF Metadata provided by EXIF.tools
FCC ID Filing: Q8S515123

Navigation menu