dormakaba Canada A38880 BLE SMART communication board User Manual Service Plan 760 lock series

Kaba Ilco Inc. BLE SMART communication board Service Plan 760 lock series

User Manual

Download: dormakaba Canada A38880 BLE SMART communication board User Manual Service Plan 760 lock series
Mirror Download [FCC.gov]dormakaba Canada A38880 BLE SMART communication board User Manual Service Plan 760 lock series
Document ID3076880
Application IDxVWUemEmAHNsm4ItRrYQ/A==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeYes
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize49.58kB (619766 bits)
Date Submitted2016-07-16 00:00:00
Date Available2017-01-12 00:00:00
Creation Date2016-07-22 15:59:57
Producing SoftwareMicrosoft® Word 2016
Document Lastmod2016-07-22 15:59:57
Document TitleService Plan 760 lock series
Document CreatorMicrosoft® Word 2016
Document Author: Omar Kone

Document No.
Revision:
BLE Module Installation Guide
Prepared by: Charles Grimm
Date: 10/22/2015
BLE Module Installation Guide
BLE_Upgrade_Modified_Rev3
1 of 5
Document No.
Revision:
BLE Module Installation Guide
Prepared by: Charles Grimm
Date: 10/22/2015
REVISION HISTORY
Rev.
Date
10/22/2015
Description
Release of document
Made by
Checked
Approved
CG
TABLE OF CONTENTS
1.
INSTALL DOUBLE DECKER END CAP .................................................................................................................................... 3
2.
LABEL UPGRADES AND ADDITIONS ...................................................................................................................................... 5
BLE_Upgrade_Modified_Rev3
2 of 5
Document No.
BLE Module Installation Guide
Prepared by: Charles Grimm
Revision:
Date: 10/22/2015
1. Install Double Decker End Cap
Install the communication boards as shown.
RF board is in the upper position if present.
BLE board is in the lower position.
Ensure the wires run through the notch in
the cap so they do not become pinched
when the cap is installed on the chassis.
Install the end cap onto the chassis by pressing it
over the screw post as shown.
BLE_Upgrade_Modified_Rev3
3 of 5
Document No.
BLE Module Installation Guide
Prepared by: Charles Grimm
Connect the BLE module
wire harness to the MT4
PCB as shown.
Ensure all wires are
connected and routed
properly and will not be
pinched when the cover is
reinstalled.
Zigbee Connection
(If applicable)
BLE Connection
BLE_Upgrade_Modified_Rev3
4 of 5
Revision:
Date: 10/22/2015
Document No.
Revision:
BLE Module Installation Guide
Prepared by: Charles Grimm
Date: 10/22/2015
2. Label Upgrades and Additions
Ensure the “DEAD BOLT CAM POSITION”
label is replaced with the latest MT4 version.
Part Number: A37780
The FCC Enclosure label for the BLE board
must be added to the lock and will be placed as
shown for field upgrades.
Note: Part displayed is the inside cover
Reinstall the escutcheon and tighten the screws
with a tamper resistant T20 bit.
Regulatory Compliance:
This device complies with Part 15 of the FCC Rules,. Operation
is subject to the following two conditions: (1) this device may not
cause harmful inter-ference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Any changes or modifications of this product, not approved by
manufacturer will void the user’s authority to operate the
equipment.
“This device complies with Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may
cause undesired operation of the device.”
BLE_Upgrade_Modified_Rev3
5 of 5

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 5
Language                        : en-US
Tagged PDF                      : Yes
Title                           : Service Plan 760 lock series
Author                          : Omar Kone
Creator                         : Microsoft® Word 2016
Create Date                     : 2016:07:22 15:59:57-04:00
Modify Date                     : 2016:07:22 15:59:57-04:00
Producer                        : Microsoft® Word 2016
EXIF Metadata provided by EXIF.tools
FCC ID Filing: Q8SA38880

Navigation menu