dormakaba EAD KRR9125-K5 Desktop Reader User Manual TM RemoteReader9125 AM US CAN 201603 en
Kaba GmbH Desktop Reader TM RemoteReader9125 AM US CAN 201603 en
user manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3156567 |
| Application ID | FTQAXsW4DrcQrcOdtgUrEA== |
| Document Description | user manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 130.16kB (1626939 bits) |
| Date Submitted | 2016-10-06 00:00:00 |
| Date Available | 2016-10-06 00:00:00 |
| Creation Date | 2016-04-26 15:50:55 |
| Producing Software | ST4 PDF Engine (Build 5.0.2.4) |
| Document Lastmod | 2016-04-26 15:50:55 |
| Document Title | TM_RemoteReader9125-AM-US-CAN_201603_en |
| Document Creator | SCHEMA ST4 |
Kaba Remote Reader 91 25-AM (US/CAN)
Technical Manual
04045708 - 04/2016
EN
Kaba AG
Access & Workforce Management
Hofwisenstrasse 24
8153 Rümlang
Switzerland
Kaba AG
Access & Workforce Management
Mühlebühlstrasse 23
8620 Wetzikon
Switzerland
Kaba GmbH
Access & Workforce Management
Albertistraße 3
78056 Villingen-Schwenningen
Germany
Phone +41 44 818 93 11
www.kaba.com
Phone +41 44 931 61 11
www.kaba.com
Phone +49 7720 603 0
www.kaba.com
This document must not be reproduced in any way or otherwise further used without the written consent of Kaba AG.
All product names are trademarks of the respective companies.
Copyright 2016 Kaba AG. All rights reserved.
04045708 - 04/2016
Technical Manual
Contents
Contents
About this Document ............................................................................................................................. 7
1.1
Validity............................................................................................................................................................................... 7
1.2
Target group ................................................................................................................................................................... 7
1.3
Contents and purpose................................................................................................................................................. 7
1.4
Supplementary Documents ...................................................................................................................................... 8
1.5
Change Log ..................................................................................................................................................................... 8
1.6
Orientation in the Document.................................................................................................................................... 8
1.7
Abbreviations/Term Definitions .............................................................................................................................. 9
1.8
Warnings......................................................................................................................................................................... 10
1.8.1 Hazard Categories ........................................................................................................................................ 10
1.8.2 Symbols............................................................................................................................................................ 10
1.9
Notes................................................................................................................................................................................ 10
Grouped safety messages.................................................................................................................... 11
2.1
Use as directed ............................................................................................................................................................. 11
2.2
Mounting and Installation........................................................................................................................................ 11
2.3
Service and Maintenance ......................................................................................................................................... 11
2.4
Accessories and spare parts .................................................................................................................................... 11
2.5
ESD (electrostatic discharge) protective measures......................................................................................... 12
Product Description ............................................................................................................................. 13
3.1
Overview......................................................................................................................................................................... 13
3.2
Registration Unit Compatibility ............................................................................................................................. 14
3.3
Operating modes ........................................................................................................................................................ 15
3.4
Supported RFID Standards with Possible Media Definitions....................................................................... 16
3.4.1 MIFARE ............................................................................................................................................................. 16
3.4.2 LEGIC ................................................................................................................................................................. 16
3.5
Interface for Extension Modules ............................................................................................................................ 18
3.5.1 Number of Supported Extension Modules ......................................................................................... 18
3.6
Technical Data .............................................................................................................................................................. 19
3.6.1 Overview of Technical Data...................................................................................................................... 19
3.6.2 Dimensions ..................................................................................................................................................... 21
3.7
Conformity..................................................................................................................................................................... 22
3.8
Labeling .......................................................................................................................................................................... 24
Design and function ............................................................................................................................. 25
4.1
Device structure........................................................................................................................................................... 25
4.2
Firmware......................................................................................................................................................................... 26
4.3
System Requirements................................................................................................................................................ 26
4.4
Behavior with two Registration Units .................................................................................................................. 27
4.5
Behavior with Several Media in the Field (Anti-Collision)............................................................................. 27
4.6
Functions........................................................................................................................................................................ 28
4.7
LED Display .................................................................................................................................................................... 30
4.8
Operating Types .......................................................................................................................................................... 31
4.8.1 Overview of Operating Types .................................................................................................................. 31
Kaba Remote Reader 91 25-AM (US/
CAN)
04045708 - 04/2016
Contents
Technical Manual
4.8.2
4.8.3
4.9
Online operation........................................................................................................................................... 32
Offline Operation.......................................................................................................................................... 32
Operating modes ........................................................................................................................................................ 34
4.9.1 'Electric strike' operating mode............................................................................................................... 35
4.9.2 'Motor Bolt' Operating Mode ................................................................................................................... 36
4.9.3 'Automatic door' operating mode ......................................................................................................... 37
4.9.4 'Turnstile' operating mode........................................................................................................................ 38
4.9.5 'Night lock' operating mode..................................................................................................................... 39
4.9.6 'Motor bolt with panic function' operating mode............................................................................ 41
4.9.7 'Motor bolt type II with panic function' operating mode (2 outputs) ....................................... 42
4.9.8 'Motor bolt type III with panic function' operating mode (1 output)........................................ 44
4.9.9 'Electric lock with panic function' operating mode ......................................................................... 46
4.9.10 'Automatic door with night lock' operating mode .......................................................................... 48
4.9.11 'Online Operation' Operating Mode...................................................................................................... 49
Installation ............................................................................................................................................ 50
5.1
Installation process..................................................................................................................................................... 50
5.2
Installation conditions ............................................................................................................................................... 51
5.2.1 General ............................................................................................................................................................. 51
5.2.2 Installation site .............................................................................................................................................. 51
5.2.3 Connections ................................................................................................................................................... 51
5.3
Installation layout (example)................................................................................................................................... 52
5.4
Installation lines ........................................................................................................................................................... 53
5.4.1 Power supply line ......................................................................................................................................... 53
5.4.2 Data line RS-485............................................................................................................................................ 55
5.4.3 Line to the door opener and door contacts........................................................................................ 57
5.4.4 Coaxial Cable to the Registration Units................................................................................................ 58
5.4.5 RS-232 Connection ...................................................................................................................................... 58
5.4.6 Grounding Concept..................................................................................................................................... 59
5.5
Mounting the device and extension modules.................................................................................................. 60
5.6
Connections .................................................................................................................................................................. 62
5.6.1 Connections, General.................................................................................................................................. 63
5.6.2 Power Supply ................................................................................................................................................. 63
5.6.3 RS-485 interface ............................................................................................................................................ 63
5.6.4 'Ant. A' and 'Ant. B' Connections............................................................................................................. 63
5.6.5 RS-232 A and RS-232 B Interfaces........................................................................................................... 64
5.6.6 Programming Interface .............................................................................................................................. 64
5.6.7 Interface for Extension Modules ............................................................................................................. 64
5.6.8 Inputs IN1 – IN4, tamper and input 5 ................................................................................................... 65
5.6.9 Output OUT1 – OUT3 .................................................................................................................................. 67
5.7
Configuring.................................................................................................................................................................... 68
5.7.1 Configuration process ................................................................................................................................ 68
5.7.2 Change Settings............................................................................................................................................ 68
5.7.3 Set RS-485 termination resistances ....................................................................................................... 69
5.7.4 Set peripheral addresses............................................................................................................................ 71
5.7.5 Set Operating Mode .................................................................................................................................... 71
5.7.6 Set functions .................................................................................................................................................. 72
Start-up ................................................................................................................................................. 80
6.1
Putting into operation process .............................................................................................................................. 80
6.2
"Standalone Access Control without Host System" Commissioning ....................................................... 80
6.2.1 Using LEGIC .................................................................................................................................................... 80
6.2.2 Using MIFARE................................................................................................................................................. 81
04045708 - 04/2016
Kaba Remote Reader 91 25-AM (US/
CAN)
Technical Manual
10
Contents
6.3
Functional Test (RS-232 A/B) ................................................................................................................................... 83
6.4
Issue Write/Read Authorization (Launch)........................................................................................................... 84
6.5
Cancel Write/Read Authorization.......................................................................................................................... 85
6.5.1 Cancel all writing rights granted by a write authorization............................................................ 85
6.5.2 Cancel a particular writing right granted by a write authorization:........................................... 85
Servicing................................................................................................................................................ 86
7.1
Programming interface............................................................................................................................................. 86
7.2
Restart.............................................................................................................................................................................. 86
7.3
Service mode ................................................................................................................................................................ 87
7.3.1 Enable service mode ................................................................................................................................... 87
7.3.2 Disable service mode .................................................................................................................................. 87
7.4
Factory Reset/Reset Device to the Basic Status................................................................................................ 88
7.5
Firmware Update/LEGIC OS Update..................................................................................................................... 90
7.5.1 Firmware update/LEGIC OS update via access manager............................................................... 90
7.5.2 Firmware Update / LEGIC OS Update with programmer 1460 .................................................... 90
7.6
Crossgrade ..................................................................................................................................................................... 92
7.6.1 Device with Bxxx firmware (MRD) .......................................................................................................... 92
Troubleshooting................................................................................................................................... 93
8.1
LED Displays on the Remote Reader .................................................................................................................... 93
8.2
During Installation ...................................................................................................................................................... 93
8.3
During operation......................................................................................................................................................... 94
Packaging/Return................................................................................................................................. 96
9.1
Complete Devices ....................................................................................................................................................... 96
9.2
Electronic Assemblies ................................................................................................................................................ 96
9.3
Marking ........................................................................................................................................................................... 96
Disposal ................................................................................................................................................. 98
10.1
Decommissioning ....................................................................................................................................................... 98
10.2
Dismantling ................................................................................................................................................................... 98
10.3
Disposal........................................................................................................................................................................... 98
Index .................................................................................................................................................... 100
Kaba Remote Reader 91 25-AM (US/
CAN)
04045708 - 04/2016
Contents
Technical Manual
04045708 - 04/2016
Kaba Remote Reader 91 25-AM (US/
CAN)
Technical Manual
About this Document
About this Document
1.1
Validity
This document describes all device versions and optional equipment and functions.
Options need to be paid for and are therefore only available if they have been purchased. Additional equipment and functions may not yet be available at the time of
issuing the document and, possibly, can only be purchased at a later stage.
Product name:
Kaba remote reader 91 25 (US / CAN)
Article number:
04044475
Functional type:
AM (access manager)
Serial number:
Date of manufacture:
Firmware version
from BREB03.05.RD_
Display in Kaba exos: BREB03.05.RD
1.2
Target group
This document is exclusively intended for specialist personnel.
The descriptions require specialist personnel trained by the manufacturer. The descriptions do not replace product training.
For reasons of device safety, the installation and maintenance operations described
in this document must be carried out only by service persons according to EN
60950-1 (Information technology equipment - Safety).
Service persons are persons having adequate technical training and sufficient experience to be aware of and to minimize the possible risks for themselves or other persons, which may occur when carrying out these operations. The service persons are
responsible for adhering to the instructions given by the manufacturer and to the applicable standards and regulations during execution of their work.
This document is also used as information for persons with the following tasks:
1.3
•
project planning and implementation
•
Commissioning the product within the network
•
Connecting the product to the user software by programming customer applications
•
Customer-specific adjustment by setting the parameters of the product
Contents and purpose
The contents is limited to the assembly, installation, start-up, and basic operation of
the hardware.
Kaba Remote Reader 91 25-AM (US/
CAN)
04045708 - 04/2016
About this Document
1.4
Technical Manual
Supplementary Documents
Supplementary documentation is available on the Kaba website. The technical manuals are located in a secured area of the website.
•
Access is only possible after logging in.
•
An account will need to be created before logging in for the first time.
Access and login:
1. In the browser, access the Kaba page http://www.kaba.com.
2. Select the language in the top right.
3. Under "Products", select the "Access Management" or "Workforce Management"
product division.
4. In the top right section of the screen, click on the following symbol:
5. Enter your e-mail address and password and login or create an account (see below).
ð The technical manuals can be found under "Downloads".
Create account:
1. Click "Create account".
2. Complete the data fields and confirm.
ð A confirmation link will be sent to your e-mail address.
3. To activate your account, click on the confirmation link in your e-mail.
1.5
Change Log
The most important changes to the last issue of this manual are listed below:
1.6
Version number
Edition
Brief description
TM_RemoteReader9125-AM-USCAN_201603
03/2016
First edition (US /
CAN)
Orientation in the Document
This document contains the following orientation aids to facilitate finding of specific
topics:
•
An index in the alphabetical order is given at the end of the manual.
•
The table of contents at the beginning of the manual gives an overview of all
topics.
•
The header always contains the respective main chapter.
•
This step-by-step guide goes through the installation and commissioning.
•
Cross references always indicate the number of the chapter in which the supplementary information can be found. Example [ 5.7].
04045708 - 04/2016
Kaba Remote Reader 91 25-AM (US/
CAN)
Technical Manual
1.7
About this Document
Abbreviations/Term Definitions
Abbreviations and terms used in this document:
Abbreviation/
term
Term definition from 07/01/14
Remote reader
Kaba remote reader 91 25
Device
Kaba remote reader 91 25
Door manager
Kaba remote reader 91 25
Registration unit
Kaba registration unit 90 01
Kaba registration unit 90 02
Kaba registration unit 90 00
Antenna
Registration unit
Extension module
Kaba extension module 90 31
Kaba extension module 90 30
Host
Host system
KCP
Kaba Communication Protocol (RS-485)
BPA/9 subset
Protocol for subterminal communication via RS-485 BPA =
Benzing Protocol Asynchronous
Control unit
•
Access manager or
•
B-web terminal
KMM
Kaba Media Manager
Access Manager
Kaba access manager 92 00
Kaba exos AMC
Kaba exos AMCII
Programmer
Kaba Programmer 1460
Authorized access
Is active until the door is closed again or the alert duration has
expired
Door opener key
Key which triggers single, authorized door opening
Door handle contact
Contact in the door handle with which authorized door opening is reported to the system
Frame contact
Contact in the door frame with which the door status open or
closed is reported
Blocking contact
Contact with which the access point can be blocked. In this
case, any identification on the registration unit is rejected as
access not authorized and signaled accordingly.
Alarm buzzer/alarm This signal is used to control the relay output if the door is
relay
forced open or in the event of 'Door open too long'
Hold-open mode
Kaba Remote Reader 91 25-AM (US/
CAN)
In the event of authorized access, the door remains activated
(opened) until the user medium is within the range (field) of
the antenna.
04045708 - 04/2016
About this Document
1.8
Technical Manual
Warnings
Warnings containing information/instructions and prohibitions to prevent injury to
persons and damage to property are specially labeled.
Please pay attention to warnings. They are intended to help prevent accidents and
avoid damage.
1.8.1
Hazard Categories
Warnings are split into the following categories:
CAUTION
Slight Risk
Describes a potentially hazardous situation that could result in minor physical injuries.
NOTICE
Information on how to handle the product correctly.
Failure to comply with these warnings may result in malfunctions. The product or
something in its vicinity could be damaged.
1.8.2
Symbols
Depending on the source of the hazard, symbols are used for the warnings, and
these have the following meanings:
General danger
1.9
Danger for electronic components from electrostatic discharge
Notes
Notes are labeled with an info symbol.
Tips and useful information.
These help you to make best use of the product and its functions.
10
04045708 - 04/2016
Kaba Remote Reader 91 25-AM (US/
CAN)
Technical Manual
Grouped safety messages
Grouped safety messages
This product has been built in accordance with state-of-the-art standards and the
recognized safety rules. Nevertheless, its use may constitute a risk to persons and
cause damage to material property.
Read and observe the following safety instructions before using the product.
2.1
Use as directed
The product is only intended for use as described in chapter “Product description”.
Any use beyond that is considered contrary to its designated use. The manufacturer
cannot be held liable for damage resulting from such use. Such use is at the sole risk
of the user/operator.
2.2
Mounting and Installation
Mounting and installation may only be carried out by service persons (see chapter 1
“Target group”).
Installation may only be carried out in places that fulfill the climatic and technical
conditions stated by the manufacturer.
The manufacturer is not liable for damages resulting from improper handling or incorrect installation.
2.3
Service and Maintenance
Maintenance work / troubleshooting
Only the service person (see chapter 1 “Target group”) is entitled to remove faults
and carry out maintenance work.
Reconstruction and modification
Any alteration or modification to the device may only be performed by the service
person (see chapter 1 “Target group”). Any alteration or modification performed by
unauthorized persons shall render void any liability.
2.4
Accessories and spare parts
Accessories and spare parts must comply with the technical requirements specified
by the manufacturer. This is guaranteed when using original accessories and spare
parts from Kaba.
Kaba Remote Reader 91 25-AM (US/
CAN)
04045708 - 04/2016
11
Grouped safety messages
2.5
Technical Manual
ESD (electrostatic discharge) protective measures
NOTICE
Danger for electronic components due to electrostatic discharge.
Improper handling of printed circuit boards or components can cause damages that
lead to complete failures or sporadic errors.
12
•
During installation and repair of the product, the ESD protective measures must
be considered.
•
Wear an ESD wristband when handling electronic components. Connect the end
of the wristband to a discharge socket or an unvarnished grounded metal component. This way, static charges are discharged from your body securely and effectively.
•
Touch only the edges of circuit boards. Do not touch the circuit board nor the
connector.
•
Place all dismantled components on an antistatic surface or in an antistatic container.
•
Avoid contact between circuit boards and clothing. The wristband only protects
the printed circuit boards against electrostatic discharge from your body, but
there is still a risk of damage through electrostatic discharge from your clothing.
•
Transport and dispatch dismantled modules only in electrostatically shielded
protective bags.
04045708 - 04/2016
Kaba Remote Reader 91 25-AM (US/
CAN)
Technical Manual
Product Description
Product Description
3.1
Overview
The Kaba remote reader 91 25 with functional type AM can either control and monitor access control at access points or register coming/leaving bookings for time registration.
Two registration units can be connected to the Kaba remote reader 91 25. The remote reader has two RS-232 interfaces (e.g. for keypads, Hyper X or system-dependent functions) and can be integrated into the Kaba exos access control system. The
remote reader is installed on a DIN rail. Thanks to the separation of the remote reader
and registration units, the remote reader can be installed in a tamper-proof area and
the registration units can be installed in an area that is not tamper-proof.
The door components (locking elements, monitoring contacts) are directly connected to the remote reader. This controls the electric strikes as well as the optical
and acoustic signal transmitters of the registration units. As two registration units can
be connected, one Kaba remote reader 91 25 is sufficient for implementing an on/off
configuration (e.g. turnstile). The remote reader communicates with the host system
via the RS-485 interface. The host system checks the company codes and the user
medium numbers, and activates the access points.
If the communication between the remote reader and the host system is interrupted,
then, with the relevant programming of its offline behavior, the remote reader automatically takes on the tasks of the host system; i.e. authorization checks and door
functions are retained.
Access Management System
Kaba exos 9300
(US / CAN)
Communication
Hub
Database
Web- and Application Service
91 08
Access manager
92 00 1)
90 30 90 31
Reader
91 15
91 25
Registration units
90 00
Ethernet
90 02
USB
CardLink
RS-485
Coaxial cable
90 01
1)
92 00 exos Client
Kaba Remote Reader 91 25-AM (US/
CAN)
04045708 - 04/2016
13
Product Description
3.2
Technical Manual
Registration Unit Compatibility
The following registration units are supported.
Registration unit
Control unit
Access Manager
Remote reader
Functional type
Access manager
Kaba registration unit 90 00
✔
✔
Kaba registration unit 90 01
✔
✔
Kaba registration unit 90 02
✔
✔
Registration unit
FCC
Kaba registration unit 90 00
Tested Standard: FCC Tested Standard: IndusCode of Federal Regula- try Canada Radio Stantions, CFR 47, Part 15,
dards Specifications
Sections 15.205, 15.207, RSS-GEN Issue 4, Sec15.215 and 15.225
tions 8.8, 8.9 and 8.10
and RSS-210 Issue 8,
Section A2.6 (Category I
Equipment)
Kone registration unit PCB
Kaba registration unit 90 01
Kone registration unit 90 01
Kaba registration unit 90 02
Kone registration unit 90 02
14
04045708 - 04/2016
IC
Kaba Remote Reader 91 25-AM (US/
CAN)
Technical Manual
3.3
Product Description
Operating modes
The door configuration determines the operating mode of the Remote reader. A detailed description of the door configurations and their operating modes can be
found in the chapter Operating Types and Modes.
Kaba Remote Reader 91 25-AM (US/
CAN)
04045708 - 04/2016
15
Product Description
3.4
Technical Manual
Supported RFID Standards with Possible Media Definitions
The following table shows the RFID standards and media definitions supported by
the device.
The Kaba remote reader 91 25 recognizes up to eight different media definitions at
the same time.
Media definitions
Supported RFID technologies
Unique number (UID)
*1
MIFARE
DESFire
MILEGIC advant
FARE Classic
LEGIC pri
me
ISO
14443A
ISO
14443A
LEGIC RF
✔
✔
ISO
14443A
✔
ISO
15693
✔
Safe UID
✔
Card ID
✔
✔
✔
✔
Kaba group header
✔
✔
✔
Kaba advant ID
✔
✔
LEGIC access™
(advant)
✔
✔
LEGIC access™ pool
(prime)
✔
CardLink
1.1
Data
✔
✔
✔
✔
Actuator
status
✔
✔
✔
✔
Media
traceback
*2
✔
✔
CardLink 1 Data incl.
.0
actuator
status
✔
Additional media
numbers
✔
✔
✔
✔
✔
*1 The LEGIC chip set does not use the safe UID command set
so that UID from other media, such as MIFARE, can also be
read.
*2 Media traceback information can only be read out directly
on the access manager and no media traceback information is written.
3.4.1
MIFARE
The system can evaluate everything that can be defined in Kaba media manager. MIFARE DESFire or MIFARE Classic media can be read and described on the same Kaba
remote reader 91 25 MIFARE using various media applications.
3.4.2
LEGIC
LEGIC prime or LEGIC advant media can be read and described on the same Kaba remote reader 91 25 LEGIC using various media applications (LEGIC advant media can
only be described using LEGIC advant components).
16
04045708 - 04/2016
Kaba Remote Reader 91 25-AM (US/
CAN)
Technical Manual
Product Description
Dual chip card
A dual chip card with LEGIC advant (14443 A) and CardLink LEGIC prime (LEGIC RF) is
supported.
Kaba Remote Reader 91 25-AM (US/
CAN)
04045708 - 04/2016
17
Product Description
Technical Manual
3.5
Interface for Extension Modules
3.5.1
Number of Supported Extension Modules
The extension modules are connected to the system bus of the Kaba remote reader
91 25. There is a limit to the maximum number of supported extension modules.
The host system determines the maximum number of connectible extension modules.
Configuration of the Kaba Max. connectible
remote reader 91 25
extension modules 90 30
Max. connectible
extension modules 91 31
Minimum supply voltage
of the Kaba remote reader
91 25
Only extension module
90 30
20 VDC*
Only extension modules
90 31
As specified in the technical
data: 10 VDC
Mixed operation (extension
modules 90 30 and extension modules 90 31)
As specified in the technical
data: 10 VDC
*non-standard
18
04045708 - 04/2016
Kaba Remote Reader 91 25-AM (US/
CAN)
Technical Manual
Product Description
3.6
Technical Data
3.6.1
Overview of Technical Data
Mechanics
Mounting
•
Indoors
•
On DIN rail in accordance with EN 50022
Housing
•
ABS black, with imprinted connection diagram
Combustion category
•
HB (UL94)
Dimensions
•
125 x 102 x 45 mm (L x W x H) or seven space units
17.5 mm width measurement includes screw/plug
terminals
Connections
•
All connections are screw/plug terminals
•
Max. terminal load: 5 A
Power supply
Input voltage, without ex- •
ternal wiring
•
The Remote reader sup•
plies connected devices
•
with power via the RS-232
connection.
10–34 VDC (50/60 Hz), current consumption max.
330 mA, max. 4.5 W
Power consumption/heat capacity:
–
at 12 VDC typically 2 W
–
at 24 VDC typically 2.7 W
5 VDC
max.* 1 A (at 25°C)
* Total of all connected devices
Notice: The device may only be supplied with SELV (Safety Extra Low Voltage) and
LPS (Limited Power Source), according to IEC/UL/CSA 60950-1.
Interfaces
HF RFID
Two RS-232 (A/B)
Basic setting (can be parameterized)
Kaba Remote Reader 91 25-AM (US/
CAN)
•
Two registration units with or without keypads
(ant. A/B)
•
Coaxial cable, impedance 50 Ohm
•
Encrypted data transfer
Connection with following (default) properties:
•
Connection for registration units (keypads, wide
area access solution, as well as system-dependent
functions)
•
Baud rate max. 115 200 baud (Kaba exos AM:
9600 baud)
•
8 data bits, no (None) parity, 1 stop bit
•
Output voltage 5 VDC, max. 500 mA each
•
Via Kaba exos AM can be parameterized up to
9600 baud
04045708 - 04/2016
19
Product Description
Technical Manual
Interfaces
RS-485
•
For the connection to access hub
•
KCP protocol; galvanically separated, 2-wire
•
Baud rate 19200 baud (fixed)
•
8 data bits, even (Even) parity, 1 stop bit
•
Termination resistance for bus or star wiring
•
Addressing 1–8
Programmer interface
•
For firmware update or programmer connection
Extension modules
•
Maximum number of supported extension modules, see chapter 3.5
•
With internal power supply and common ground,
for connection of insulated switches
•
Maximum 5 V DC
•
Line monitoring (can be disabled)
•
LED status indicator
•
In operating mode Kaba exos lock for the door handle contact
•
Status indicator (LED OUT1 and OUT2)
•
Switchover contact, max. voltage 34 VDC max. current 2 A at 30 VAC/DC
•
Switching cycles at 30 VDC/1A
Inputs and outputs
5 binary inputs
one of which can be used
as a tamper switch (usually IN5).
2 internal inputs
3 relay outputs
typical 500,000 (VdS 2358 requirement is 200,000)
•
Switching cycles at 30 V DC/2A
typical 100,000
•
Status indicator
•
Operating temperature: 0 °C to +50 °C
•
Storage temperature: -20 °C to +65 °C
•
Relative humidity: 0% to 95%, non-condensing
•
Protection type: IP20
Ambient conditions
Ambient conditions
20
04045708 - 04/2016
Kaba Remote Reader 91 25-AM (US/
CAN)
Technical Manual
3.6.2
Product Description
Dimensions
RS-232 B
RS-232 A
Ant. B
A+
84
IN4
102
91 25
DIN-Rail
Function
IN3
OUT1
1. Push
0-F
OUT2
OUT3
04045708 - 04/2016
Supply 10-34VDC
VsVs+
OUT3
Output max. 34VDC/27VAC/2A
OUT2
GND
IN2
GND
IN3
GND
IN1
GND
GND
IN5/TP
Relay Output Class II
Input max. 5VDC
VsVs+
Address
RS-485
BCD
Kaba Remote Reader 91 25-AM (US/
CAN)
IN1
789A
EF012
3456
2.
IN2
91 25
OUT1
BCD
Mode
IN4
EF012
789A
Click
0-F
8 Service
ON
OFF
Ant. A
State
Prog.
3456
A+
AS
AS
45
0V
Rx
Tx
5V
5V
Rx
Tx
0V
125
21
Product Description
3.7
Technical Manual
Conformity
This product conforms to the following standards:
EN 60950-1 : 2014-08
EN 60950-1:2006/A2:2013
UL 60950-1:2007/R:2014-10
CAN/CSA-C22.2 No. 60950-1:2007/A2:2014-10
EN 301 489-1 V1.9.2 : 2011-09
EN 301 489-3 V1.6.1 : 2013-08
EN 300 330-1 V1.8.1 : 2014-12
EN 300 330-2 V1.6.1 : 2014-12
in accordance with the provisions of the EC directives
2014/53/EC: R&TTE Directive
RoHS
This device complies with the regulations of the Directive 2011/65/EU of the European Parliament and of the Council of June 8, 2011, on the restriction of the use of
certain hazardous substances in electrical and electronic equipment.
The original Declaration of Conformity can be downloaded from
www.kaba.com/conformity in PDF format.
Tested Standard:
FCC Code of Federal Regulations, CFR 47, Part 15, Sections 15.205, 15.207, 15.215 and
15.225
FCC ID NVI-KRR9125-K5
FCC § 15.19
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause
undesired operation.
FCC § 15.21 (Warning Statement)
[Any] changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
FCC § 15.105
Note: This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own expense.
Tested Standard:
Industry Canada Radio Standards Specifications RSS-GEN Issue 4, Sections 8.8, 8.9
and 8.10 and RSS-210 Issue 8, Section A2.6 (Category I Equipment)
IC:11038A-KRR9125-K5
ICES-003
This Class A digital apparatus complies with Canadian ICES-003. Cet appareil
numérique de la classe A est conforme à la norme NMB-003 du Canada.
22
04045708 - 04/2016
Kaba Remote Reader 91 25-AM (US/
CAN)
Technical Manual
Product Description
Canada RSS-GEN 8.4
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes : 1) l’appareil ne doit pas produire de brouillage; 2) l’utilisateur de l’appareil
doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Kaba Remote Reader 91 25-AM (US/
CAN)
04045708 - 04/2016
23
Product Description
3.8
Technical Manual
Labeling
The identification plate is located on the side of the device.
The following information can be found on the identification plate:
24
•
Device designation
•
Article number
•
Serial number
•
Function type
•
Connection data (power supply)
•
CE mark
•
WEEE mark as per DIN EN 50419
04045708 - 04/2016
Kaba Remote Reader 91 25-AM (US/
CAN)
Technical Manual
Design and function
Design and function
4.1
Device structure
RS-232 B
16
RS-232 A
Ant. B
3456
A+
IN1
91 25
DIN-Rail
IN3
IN4
OUT1
1. Push
0-F
OUT2
789A
12
11
OUT3
Relay Output Class II
10
VsVs+
Supply 10-34VDC
VsVs+
OUT3
Output max. 34VDC/27VAC/2A
OUT2
GND
IN2
GND
IN3
Input max. 5VDC
GND
IN1
GND
GND
BCD
Address
RS-485
IN5/TP
EF012
14
2.
IN2
91 25
Function
8 Service
ON
OFF
OUT1
BCD
Mode
13
Click
0-F
IN4
EF012
789A
15
Ant. A
State
Prog.
3456
A+
AS
AS
0V
Rx
Tx
5V
5V
Rx
Tx
0V
17
Item
Connection/switch
Remark
RS-232 interface B
Connection of peripherals
RS-232 interface A
Antenna B
Registration unit B (antenna B)
Antenna A
Registration unit A (antenna A)
LED Displays
Interface for Extension Modules
Power supply 10–34 VDC
Relay outputs OUT1–OUT3
Inputs IN1–IN4
10
Tamper switch
11
RS-485 interfaces A, B and C
Connection to the host system
12
Bus termination RS-485
Jumper for adjustment of the
termination resistance
13
Addressing RS-485, 1–8
Rotary switch for selecting the
address
14
Function
DIP switch for selecting the
function
15
Operating modes
'Mode' rotary switch for selecting the operating mode
16
Interface for Kaba programmer PD 1460
17
Not used
Kaba Remote Reader 91 25-AM (US/
CAN)
04045708 - 04/2016
e.g. 90 30/90 31
25
Design and function
Technical Manual
The functions and connections of the interfaces, inputs, relay outputs, rotary and DIP
switches are described in the chapter Design and function [} 4].
4.2
Firmware
The hardware of this product is used in various Kaba system solutions. The functions
and possible uses of the product are determined by the firmware used.
This manual solely describes the Kaba remote reader 91 25 functional type access
manager (AM).
Firmware designation
Reader type
MIFARE
LEGIC
LEGIC or MIFARE
(determined during commissioning)
MRD (multi RFID device)
RC
Compact reader
RR
Remote reader 91 15
RE
Remote reader 91 25
E300 V4 or N300/T300/U300 V3
Access Manager
Subterminal
AMC/II (cDML)
Version number
xx.xx
Version
Addition 1
Final, approved version
Addition 2
Subversion
Addition 3
Reserve
Device type
Functional type
Example
Designation of firmware for Kaba remote reader 91 25 with functional type access
manager:
•
BREB03.xxRxx (MRD)
Firmware mark on the product
Devices with firmware with the functional type access manager bear a mark reading
"Type: Access manager" on the identification plate.
4.3
System Requirements
•
Kaba exos 9300 release 4.0.1 and higher
•
Kaba access manager 92 00 AM firmware version 3.00 and higher
Further details can be found in the Release Overviews and Release Notes.
26
04045708 - 04/2016
Kaba Remote Reader 91 25-AM (US/
CAN)
Technical Manual
4.4
Design and function
Behavior with two Registration Units
The Remote reader 91 25 communicates alternately via the connections 'Ant. A' and
'Ant. B' (toggling) with the connected registration units. This means that the Remote
reader 91 25 cannot communicate with both registration units at the same time. This
results in the following behavior:
4.5
•
During a longer reading process, the other registration unit is blocked.
•
The fields of the two connected registration units do not influence each other.
This means that the two registration units can be installed close together.
•
In the case of registration units installed close together, it may be the case that
the medium is read by the two registration units one after the other.
Behavior with Several Media in the Field (Anti-Collision)
The Remote reader 91 25 can recognize several LEGIC advant user media (ISO 14443
A) in the field simultaneously. The Remote reader 91 25 only considers the first user
medium, which corresponds to the search criteria defined in the system. The remaining user media are ignored.
Kaba Remote Reader 91 25-AM (US/
CAN)
04045708 - 04/2016
27
Design and function
4.6
Technical Manual
Functions
All data for access decisions are saved in the host control device. The authorization
check of a badge and access control are undertaken by the control device.
Functions available before the remote reader is connected to the host system
Standalone access control (without host system); see chapter "Standalone Access
Control without Host System" Commissioning [} 6.2]
Access control functions
•
Authorization check using badges and temporal authorization incl. verification
•
Connection of two separate registration units
•
Control of optical and acoustic signal transmitters of the registration units
•
Control of electric strikes (doors with electrical blocking elements)
•
Support for door opener keys or door handle contacts
•
Monitoring of the door status with frame contact, bolt monitoring and door handle contact
•
CardLink support: Validation and UID additional recording (only LEGIC)
•
Inspection of the functionality even without host system
•
Two RS-232 serial interfaces, e.g., for keypads, Hyper X or system-dependent
functions, such as input or issue (only online) of user media numbers
•
Hold-open mode, so that, when access is authorized, the door remains open for
as long as the badge remains within range of the antenna (field)
•
Monitoring of a tamper switch by integrating the Remote reader into housing
•
Signal for authorized access, e.g., for alarm bypass
Restrictions with interrupted connection (offline)
MIFARE
Reduced authorization check using site keys.
Door function is retained depending on the offline parameter setting.
•
Authorization check using site keys. A maximum of eight site keys can be saved.
•
Not taken into consideration: Time zones and PIN code
•
Logbook for 2000 events
•
No room monitoring/balancing and no CardLink functionality
•
No change in fabrication key
LEGIC
Reduced authorization check using segment search keys. Door function is retained
depending on the offline parameter setting.
•
28
Authorization check using segment search keys. A maximum of eight segment
search keys can be saved.
04045708 - 04/2016
Kaba Remote Reader 91 25-AM (US/
CAN)
Technical Manual
Design and function
•
Not taken into consideration: Time zones and PIN code
•
Logbook for 2000 events
•
No room monitoring/balancing and no CardLink functionality
Restored connection
Automatic forwarding of saved bookings as well as status and alarm messages when
connection is restored.
Kaba Remote Reader 91 25-AM (US/
CAN)
04045708 - 04/2016
29
Design and function
4.7
Technical Manual
LED Display
The LED display shows operating statuses and errors. Troubleshooting tips are listed
in Chapter [} 8].
LED Designation
LED Behavior
Meaning
State
green permanent
Device in operation (offline)
flashes green
RS-485 interface in the receive or send mode (online)
orange permanent
Service mode
red permanent or off
Device defective
flashes green and orange
After an interruption in
communication, until the
device is queried for the
first time by the host system
green permanent
LED lights once the corresponding input is enabled
orange flashing
Service mode
orange permanent or off
Update via programmer
1460
IN1–IN4
orange permanent
Short circuit
Monitoring enabled
red permanent
interruption
OUT1–OUT3
green permanent
the relevant output is active
flashes green
Undervoltage (Vs) or relay
defective
red permanent
Write/read authorization
(launch data) is deleted
red permanent
Input 5 (only in Kaba exos
lock operating mode)
As soon as the door handle contact is active
IN1–IN4
OUT1
30
04045708 - 04/2016
Kaba Remote Reader 91 25-AM (US/
CAN)
Technical Manual
Design and function
4.8
Operating Types
4.8.1
Overview of Operating Types
An operating type of the Remote reader is always made up of the operating mode
(door configuration) with the associated extended functions and of the communication with the host system (access hub). The Remote reader supports the online and
offline operating types.
Online operation:
The Remote reader communicates with the system.
Offline operation:
If a Remote reader connected with the system is disconnected from the system, then the Remote reader switches
to the offline mode.
For the online and offline operation of the device, a minimum of the following hardware settings must be carried out before putting into operation:
System used
Minimum hardware settings
Kaba exos 9300
Online operation:
•
Address
Offline operation:
•
Kaba Remote Reader 91 25-AM (US/
CAN)
04045708 - 04/2016
DIP and rotary switch
31
Design and function
4.8.2
Technical Manual
Online operation
In online operation, the Remote reader communicates with the host system. The system makes the access decision on the basis of badges, time-dependent authorization
and verification. The system controls the access points. If communication between
Remote reader and system is interrupted, then the Remote reader independently
switches into offline operation. If the Remote reader is queried by the system again,
then the Remote reader switches back into online operation.
4.8.3
Offline Operation
Even in offline operation, i.e. without communication with the host system, an access
point is monitored and controlled by the Remote reader. For access decisions,
site keys are used under MIFARE and
segment search keys are used under LEGIC.
The Remote reader controls access points in accordance with the operating mode,
door configuration and the corresponding 'extended functions' (offline configuration).
In order to ensure fault-free offline operation, the Remote reader should be operated
with a secure power supply (e.g. UPS).
Offline operation can be turned off in the system and/or using the 'Mode' rotary
switch (F = off). This means that the offline behavior defined in the hardware settings
is deactivated and the access point remains blocked if there is an interruption in
communication.
Behavior in the event of an interruption to communication
•
The access point goes to the basic status (possibly alarm if the access point is not
closed)
•
Relays which are not involved in a door process (according to DIP switch) deactivate; the same is true for the connected Kaba extension module 90 30.
4.8.3.1 Offline Access Decision
The customer determines the nature of the offline access decision which is parameterized in the system. We differentiate the following offline access decisions:
Parameter settings in the system: no offline access decision
The Remote reader rejects all bookings in offline operation.
Parameter settings in the system:
Checking site key (MIFARE)/segment search key (LEGIC)
In the online mode, the site key (MIFARE)/segment search key (LEGIC) is sent to the
Remote reader by the system and saved in the Remote reader. During the offline
mode, the Remote reader only checks the site key (MIFARE)/segment search key
(LEGIC). The time zone is not considered for this kind of access decision.
Logbook
The logbook records and saves a maximum of 2000 events during the offline operation. Once the Remote reader is online again, the saved data is sent to the host system and deleted from the memory of the Remote reader.
The following events are logged:
•
Authorized accesses (incl. type of authorization)
•
Tampering, door forced open, door opener key
If there are more than 2000 entries, the oldest will be overwritten (ring memory).
Service mode
See chapter Service mode [} 7.3]
32
04045708 - 04/2016
Kaba Remote Reader 91 25-AM (US/
CAN)
Technical Manual
Design and function
Also see about this
2 7.3 Service mode [} 87]
Kaba Remote Reader 91 25-AM (US/
CAN)
04045708 - 04/2016
33
Design and function
4.9
Technical Manual
Operating modes
The operating mode of the Remote reader must be selected on the basis of the door
configuration.
The operating mode is set using the rotary switch, see Chapter Set Operating Mode.
The extended functions of a selected operating mode are set using the DIP switch
Extended functions of the operating modes [} 5.7.6.1].
Possible operating modes:
•
Electric strike; for doors with electrical blocking elements
•
Motor bolt; for doors with electrical blocking elements
•
Automatic doors; for doors with their own electronic control system (control with
enable pulse; e.g. sliding door)
•
Turnstile; for turnstiles/tripod turnstiles with their own electronic control system
(control with direction-dependent enable pulses)
•
Night lock; for doors with the two elements electronic strike and motor bolt
•
Kaba exos lock; for doors with self-locking Kaba panic locks;
•
Cylinder interface LI-EL; for doors with mechatronic Kaba elolegic cylinders
•
Motor bolt with panic function; for doors with electrical blocking elements and
additional mechanical panic opening
•
Motor bolt type II with panic function (two outputs); for doors with electrical
blocking elements and additional mechanical panic opening. 1 output each for
the pulses 'unlock' and 'lock'.
•
Motor bolt type III with panic function (1 output); for doors with electrical blocking elements and additional mechanical panic opening. 1 output for the pulses
'unlock' and 'lock'.
•
Electric lock with panic function; for doors with electrical blocking elements and
additional mechanical panic opening
•
Automatic door with night lock for doors with their own electronic control system and additional night lock
Also see about this
2 4.9.1 'Electric strike' operating mode [} 35]
34
04045708 - 04/2016
Kaba Remote Reader 91 25-AM (US/
CAN)
Technical Manual
4.9.1
Design and function
'Electric strike' operating mode
Alarm
RS-232 A/B
Access allowed
(Alarm bypass)
Intrusion
detection
system
Frame contact
(Access control)
Registration unit B
Registration unit A
Buzzer / LED
Access manager /
Door manager
Electric strike
Door opener key
Blocking contact
The 'Electric strike' operating mode is mainly used to operate doors with electric locking elements (strike, magnet).
The access authorised signal is triggered by authorised booking, the door opener key
or the door handle. So that subsequent door opening does not trigger an alarm, the
'Access authorised' signal activates the alarm bypass.
Then the electric strike is triggered. The door is now released for opening and the set
relay operating time starts to run. When the door is opened the pre-alarm and alarm
time start to run ('Door open too long').
Authorised booking,
door opener key or
door handle trigger
a door opening
Access allowed
Electric strike (not used
with a door handle)
Relais operation time
Access control
Door closed
Frame contact
Pre-alarm time
Access control
Door open
Kaba Remote Reader 91 25-AM (US/
CAN)
Alarm time
04045708 - 04/2016
35
Design and function
4.9.2
Technical Manual
'Motor Bolt' Operating Mode
Alarm
Intrusion
detection
system
RS-232 A/B
Access allowed
(Alarm bypass)
Frame contact
(Access control)
Registration unit B
Registration unit A
Buzzer / LED
Access manager /
Door manager
Blocking contact
Bolt monitoring
(locked)
Door opener key
Motor bolt
The 'motor bolt' operating mode mainly operates doors with electrical locking elements.
The 'authorized access' signal is generated through being triggered by an authorized
booking or the door opener key. So that subsequent door opening does not generate an alarm, the 'authorized access' signal activates the alarm bypass.
Then the motor bolt is activated. The door is now released for opening and the set relay operation time starts to run. When opening the door, the pre-alarm and alarm
time start to run ('Door open too long').
The motor bolt is activated until the frame contact signals that the door is closed
again. Only then will the lock of the motor bolt be extended again. If the motor bolt
is not extended (e.g. in the event of a defect or tampering), then an alarm ('Bolt position incorrect') is triggered.
Authorised booking
or door opener key
trigger a door
opening
Access allowed
Motor bolt
Relay operation time
Access control
Door locked
Bold monitoring
Access control
Door unlocked
Access control
Door closed
Frame contact
Pre-alarm time
Access control
Door open
36
Alarm time
04045708 - 04/2016
Kaba Remote Reader 91 25-AM (US/
CAN)
Technical Manual
4.9.3
Design and function
'Automatic door' operating mode
RS-232 A/B
Alarm
Intrusion
detection
system
Access allowed
(Alarm bypass)
Frame contact
(Access control)
Registration unit B
Access manager /
Door manager
Registration unit A
Buzzer / LED
Blocking contact
Door opener key
Release pulse
The 'Automatic doors' operating mode is mainly used to operate doors with their
own control electronics (e.g. sliding doors). The control is carried out using a release
pulse.
The 'Access authorised' signal is generated triggered by an authorised booking or the
door opener key. So that subsequent door opening does not trigger an alarm, the
'Access authorised' signal activates the alarm bypass.
The release pulse (approx. 1 s) is then sent to the control electronics. The set relay operation time starts to run. If the door is opened within the relay operation time, then
the pre-alarm and alarm time start to run ('Door open too long').
If the door is opened outside of the relay operation time, then unauthorised door
opening is present.
Authorised booking,
door opener key or
door handle trigger
a door opening
Access allowed
Release pulse (not used
with a door handle)
1s
Relais operation time
Access control
Door closed
Frame contact
Pre-alarm time
Access control
Door open
Kaba Remote Reader 91 25-AM (US/
CAN)
Alarm time
04045708 - 04/2016
37
Design and function
4.9.4
Technical Manual
'Turnstile' operating mode
RS-232 A/B
Alarm
Intrusion
detection
system
Access allowed
(Alarm bypass)
Frame contact
(Access control)
Registration unit B
Buzzer / LED
Frame contact
Inside
Release pulse
(direction-dependent)
Access manager /
Door manager
Blocking contact
Door opener key
Release pulse
(direction-dependent)
Outside
Buzzer / LED
Registration unit A
The 'Turnstile' operating mode is mainly used to operate turnstiles/tripod barriers
with their own control electronics (triggered with direction-dependent release
pulses). The turnstile is an access point in which the access point sides (outside/inside) are released in a direction-dependent manner. Therefore two opposite directions of rotation are possible.
The 'access authorised' signal is triggered by authorised booking or the door opener
key. So that subsequent door opening does not trigger an alarm, the 'Access authorised' signal activates the alarm bypass.
Then the direction-dependent release pulse (approx. 1 s) is sent to the control electronics and the set relay operation time starts to run. If the door is opened outside of
the relay operation time, then unauthorised door opening is present.
Authorised booking,
door opener key
trigger a door
opening
Access allowed
Direction-dependent
release puls
1s
Relais operation time
38
04045708 - 04/2016
Kaba Remote Reader 91 25-AM (US/
CAN)
Technical Manual
4.9.5
Design and function
'Night lock' operating mode
RS-232 A/B
Alarm
Intrusion
detection
system
Access allowed
(Alarm bypass)
Frame contact
(Access control)
Registration unit B
Registration unit A
Buzzer / LED
Access manager /
Door manager
Blocking contact
Electric strike
Bolt monitoring
(locked)
Door opener key
Motor bolt
The 'Night lock' operating mode is mainly used to operate doors with the two elements electric strike and motor bolt. Therefore during the day only the door opener
relay needs to be enabled, and the door can be additionally locked at night (e.g. XLock motor lock with control unit; but without bolt monitoring).
The 'access authorised' signal is triggered by authorised booking or the door opener
key. So that subsequent door opening does not trigger an alarm, the Access authorised signal activates the alarm bypass.
Then the motor bolt is triggered. As soon as the motor bolt is retracted (motor bolt
monitoring), the electric strike is triggered and the door is released for opening. The
set relay operation time starts to run. When the door is opened the pre-alarm and
alarm time start to run ('Door open too long').
•
The time profile saved for the night lock only works in online mode.
•
Offline mode always corresponds to the night setting. Motor bolt and door
opener relay are controlled.
Kaba Remote Reader 91 25-AM (US/
CAN)
04045708 - 04/2016
39
Design and function
Technical Manual
Authorised booking,
door opener key or
door handle trigger
a door opening
Access allowed
Motor bolt (not used
with a door handle)
Access control
Door locked
Bolt monitoring (not used
with a door handle)
Access control
Door unlocked
Electric strike (not used
with a door handle)
Relais operation time
Access control
Door closed
Frame contact
Pre-alarm time
Access control
Door open
40
Alarm time
04045708 - 04/2016
Kaba Remote Reader 91 25-AM (US/
CAN)
Technical Manual
4.9.6
Design and function
'Motor bolt with panic function' operating mode
Alarm
RS-232 A/B
Access allowed
(Alarm bypass)
Intrusion
detection
system
Frame contact
(Access control)
Registration unit B
Registration unit A
Buzzer / LED
Access manager /
Door manager
Blocking contact
Bolt monitoring
(locked)
Door handle contact
Motor bolt
The 'Motor bolt with panic function' operating mode is implemented in the same
way as the 'Motor bolt' operating mode. Instead of the door opener key, the door
handle contact is assessed for mechanical panic opening.
The 'access authorised' signal is triggered by an authorised booking or the door handle. So that subsequent door opening does not trigger an alarm, the 'Access authorised' signal activates the alarm bypass.
The door is now released for opening and the set relay operating time starts to run.
When the door is opened the pre-alarm and alarm time start to run ('Door open too
long').
The motor bolt is controlled until the frame contact signals that the door is closed
again. Only then will the bolt of the motor lock be extended again. If the motor bolt
is not extended (e.g. in the event of a defect or tampering), then an alarm ('Bolt position incorrect') is triggered.
Authorised booking
or door handle
trigger a door
opening
Access allowed
Motor bolt (not used
with a door handle)
Relay operation time
Access control
Door locked
Bolt monitoring (not used
with a door handle)
Access control
Door unlocked
Access control
Door closed
Frame contact
Pre-alarm time
Access control
Door open
Kaba Remote Reader 91 25-AM (US/
CAN)
Alarm time
04045708 - 04/2016
41
Design and function
4.9.7
Technical Manual
'Motor bolt type II with panic function' operating mode (2 outputs)
Alarm
Intrusion
detection
system
RS-232 A/B
Access allowed
(Alarm bypass)
Frame contact
(Access control)
Registration unit B
Registration unit A
Buzzer / LED
Access manager /
Door manager
Blocking contact
Bolt monitoring
(locked)
Door handle contact
Unlock motor bolt
Lock motor bolt
The 'Motor bolt type II' operating mode is implemented in the same way as the 'Motor bolt with panic function' operating mode. In place of the static 'Motor bolt' signal,
there is one line each for 'Motor bolt unlocking' and 'Motor bolt locking' connected
to the lock (e.g. MIWA AL-02/AL-3M).
The 'access authorised' signal is triggered by an authorised booking or the door handle. So that subsequent door opening does not trigger an alarm, the 'Access authorised' signal activates the alarm bypass.
Then the motor bolt is retracted with the 'unlock' pulse. The door is now released for
opening. When the door is opened the pre-alarm and alarm time start to run ('Door
open too long').
If the frame contact signals that the door is closed again, then the bolt of the motor
lock is extended again via the 'lock' pulse. If the motor bolt is not extended (e.g. in
the event of a defect or tampering), then an alarm ('Bolt position incorrect') is triggered. If the unlocked door (bolt monitoring) is opened again, no alarm will be generated.
42
04045708 - 04/2016
Kaba Remote Reader 91 25-AM (US/
CAN)
Technical Manual
Design and function
Authorised booking
or door handle
trigger a door
opening
Access allowed
Unlock motor bolt (not
used with a door handle)
Lock motor bolt (not used
with a door handle)
Bolt monitoring (not used
with a door handle)
Access control
Door locked
Access control
Door closed
Access control
Door unlocked
No alarm!
Frame contact
Access control
Door open
Pre-alarm time
Alarm time
Depending on the door used, it may be the case that a door opener key is parameterised as the door component in Kaba exos instead of a door handle.
Kaba Remote Reader 91 25-AM (US/
CAN)
04045708 - 04/2016
43
Design and function
4.9.8
Technical Manual
'Motor bolt type III with panic function' operating mode (1 output)
Alarm
RS-232 A/B
Access allowed
(Alarm bypass)
Intrusion
detection
system
Frame contact
(Access control)
Registration unit B
Registration unit A
Buzzer / LED
Access manager /
Door manager
Blocking contact
Bolt monitoring
(locked)
Door handle contact
Unlock motor bolt
Lock motor bolt
The 'Motor bolt type III' operating mode is implemented in the same way as the 'Motor bolt with panic function' operating mode. Instead of the static 'Motor bolt' signals, the 'Motor bolt unlocking' pulse is generated on one output and the 'Motor bolt
locking' pulse is generated on the other output.
The 'access authorised' signal is triggered by an authorised booking or the door handle. So that subsequent door opening does not trigger an alarm, the 'Access authorised' signal activates the alarm bypass.
Then the motor bolt is retracted with the 'unlock' pulse. Now the door is released for
opening. When the door is opened the pre-alarm and alarm time start to run ('Door
open too long').
If the frame contact signals that the door is closed again, then the bolt of the motor
lock is extended again via the 'lock' pulse. If the motor bolt is not extended (e.g. in
the event of a defect or tampering), then an alarm ('Bolt position incorrect') is triggered.
Authorised booking or
door handle trigger a
door opening
Access allowed
Unlock motor bolt
Lock motor bolt
(not used with a door handle)
Access control
Door locked
Bolt monitoring (not used
with a door handle)
Access control
Door unlocked
Access control
Door closed
Frame contact
Pre-alarm time
Access control
Door open
44
Alarm time
04045708 - 04/2016
Kaba Remote Reader 91 25-AM (US/
CAN)
Technical Manual
Design and function
Depending on the door used, it may be the case that a door opener key is parameterised as the door component in Kaba exos instead of a door handle.
Kaba Remote Reader 91 25-AM (US/
CAN)
04045708 - 04/2016
45
Design and function
4.9.9
Technical Manual
'Electric lock with panic function' operating mode
Alarm
Intrusion
detection
system
RS-232 A/B
Access allowed
(Alarm bypass)
Frame contact
(Access control)
Registration unit B
Registration unit A
Buzzer / LED
Access manager /
Door manager
Blocking contact
Bolt monitoring
(locked)
Door handle contact
Electric lock
The 'Electric lock with panic function' operating mode is implemented in the same
way as the 'Motor bolt with panic function' operating mode. An electric lock (e.g. XLock electric lock, MIWA AUTA/ALTA) is controlled instead of the motor bolt.
The 'access authorised' signal is triggered by an authorised booking or the door handle. So that subsequent door opening does not trigger an alarm, the 'Access authorised' signal activates the alarm bypass.
Then the electric lock is triggered. The door is now released for opening and the set
relay operating time starts to run. When the door is opened the pre-alarm and alarm
time start to run ('Door open too long').
The 'Access authorised' signal is enabled during the alarm time until the door is
locked.
If the door is opened again during this alarm time, then no alarm is generated.
46
04045708 - 04/2016
Kaba Remote Reader 91 25-AM (US/
CAN)
Technical Manual
Design and function
Authorised booking
or door handle
trigger a door
opening
Access allowed
Relay operation time
Electric lock (not used
with a door handle)
Access control
Door locked
Deadbolt contact
Access control
Door unlocked
Access control
Door closed
No alarm!
Frame contact
Pre-alarm time
Access control
Door open
Kaba Remote Reader 91 25-AM (US/
CAN)
Alarm time
04045708 - 04/2016
47
Design and function
4.9.10
Technical Manual
'Automatic door with night lock' operating mode
Alarm
RS-232 A/B
Intrusion
detection
system
Access allowed
(Alarm bypass)
Frame contact
(Access control)
Registration unit B
Access manager /
Door manager
Registration unit A
Buzzer / LED
Blocking contact
Door opener key
Release pulse
Motor bolt
Bolt monitoring
The 'Automatic door with night lock' mode is used to operate automatic doors with
the two elements release pulse and motor bolt. This means that during the day only
the release pulse is active and at night the door is additionally locked.
The 'access authorised' signal is triggered by authorised booking or the door opener
key. So that subsequent door opening does not trigger an alarm, the 'Access authorised' signal activates the alarm bypass.
Then the motor bolt is triggered. As soon as the bolt is retracted (bolt monitoring),
the release pulse (approx. 1 s) is sent to the control electronics. The set relay operation time starts to run. If the door is opened within the relay operation time, then the
pre-alarm and alarm time start to run ('Door open too long').
If the door is opened outside of the relay operation time, then unauthorised door
opening is present.
48
•
The time profile saved for the night lock only works in online mode.
•
Offline mode always corresponds to the night setting. Motor bolt and door
opener relay are controlled.
04045708 - 04/2016
Kaba Remote Reader 91 25-AM (US/
CAN)
Technical Manual
Design and function
Authorised booking
or door handle
trigger a door
opening
Access allowed
Motor bolt (not used
with a door handle)
Access control
Door locked
Bolt monitoring (not used
with a door handle)
Access control
Door unlocked
Release pulse (not used
with a door handle)
1s
Relay operation time
Access control
Door closed
Frame contact
Pre-alarm time
Access control
Door open
4.9.11
Alarm time
'Online Operation' Operating Mode
The 'Online operation' operating mode is used for purely online operation. If communication to the host system is interrupted, then no locking elements will be activated.
All connected outputs and relays drop off.
Kaba Remote Reader 91 25-AM (US/
CAN)
04045708 - 04/2016
49
Installation
Technical Manual
Installation
This chapter describes the installation of the device.
5.1
Installation process
Procedure
1. Determine the installation site.
Installation site [} 5.2.2]
2. Lay the installation cables.
Installation lines [} 5.4]
3. Secure the device.
4. Connect registration units.
'Ant. A' and 'Ant. B' Connections [} 5.6.4],
Coaxial Cable to the Registration Units [} 5.4.4],
Coaxial Cable Terminal [} 5.4.6.4]
5. Check read behavior without system configuration:
Book with an ISO 14443 A medium or Legic Prime medium.
ð If the medium can be read, the registration unit signals this as unauthorized
access.
6. Connect keypads or system-dependent functions.
RS-232 A and RS-232 B Interfaces
7. Connect the inputs.
Inputs IN1 – IN4, tamper and input 5 [} 5.6.8]
8. Connect the relay outputs.
Output OUT1 – OUT3 [} 5.6.9]
9. Plug in/connect extension modules where required.
10. Connect Kaba remote reader 91 25 and host device to the RS-485 bus cable.
RS-485 interface [} 5.6.3]
Configure the device after installation.
Configuring [} 5.7]
Also see about this
2 5.5 Mounting the device and extension modules [} 60]
2 5.4 Installation lines [} 53]
2 5.7 Configuring [} 68]
50
04045708 - 04/2016
Kaba Remote Reader 91 25-AM (US/
CAN)
Technical Manual
Installation
5.2
Installation conditions
5.2.1
General
An accurate installation of all components is a basic requirement for a properly functioning device. The following installation instructions must be adhered to.
5.2.2
Installation site
The device is assembled on a DIN rail in a housing or IT cabinet.
The device should be installed in a tamper-proof location within the area to be secured.
Electromagnetic fields
The device must not be installed in the area of strong electromagnetic fields caused
by switching power supply, power lines, phase controllers, etc.!
5.2.3
Connections
The following connections must be available at the location where the access manager is to be installed:
•
Power supply for the device
•
RS-485 cable to the host device
•
Cables to door openers and switches
•
Coaxial cable to registration units
The installation lines have to be flush with the surface or be laid in the vandal-proof
area.
Kaba Remote Reader 91 25-AM (US/
CAN)
04045708 - 04/2016
51
Installation
5.3
Technical Manual
Installation layout (example)
91 25
DC
Kaba remote reader 91 25
Kaba access manager 92 00
Door frame contact
Door contact, door opener
Power supply
Kaba registration unit
Installation cables
52
Data line
Power supply line
Line to the door opener and door contacts (if required)
Coaxial cable
04045708 - 04/2016
Kaba Remote Reader 91 25-AM (US/
CAN)
Technical Manual
5.4
Installation
Installation lines
This chapter describes:
•
Line requirements
•
Maximum permitted line length
•
Grounding concept
The chapter Connections describes the assignment of connections and switch settings.
Only connect the terminals when the power is switched off.
5.4.1
Power supply line
The device can be supplied with power in the following ways:
•
From the host control device (power supply and data line in one cable)
•
From a separate power supply
NOTICE
Voltage drops, caused by line resistance, must be taken into consideration for
long lines.
The given cable types and diameters are examples and serve as recommendations.
The technical specifications of the cable manufacturer are authoritative for the precise determination of the cable diameter/cross section and the resulting maximum
cable lengths. The voltage drop across the cable length is decisive in this case. As
such, the voltage that is available at the end of the cable may, under no circumstances, be less than the minimum permitted supply voltage of the connected components. This always applies in consideration of the maximum power consumption
of the connected components.
Only connect the terminals when the power is switched off.
The device may only be supplied with SELV (Safety Extra Low Voltage) and LPS (Limited Power Source), according to IEC/UL/CSA 60950-1.
Kaba Remote Reader 91 25-AM (US/
CAN)
04045708 - 04/2016
53
Installation
Technical Manual
5.4.1.1 Power supply from the host control device
(Central power supply)
Power is supplied from the host control device.
In the case of bus wiring, the power supply and data line can be carried in one cable
(maximum total length of 350 m).
In the case of star wiring, the power supply and data line can be carried in one cable
(maximum length per stub of 20 m).
A separate power supply must be used for greater distances.
Permissible Cable Lengths and Cable Types
Type of wiring:
Max. cable length:
Star
Bus
< 20 m
(per stub)
< 50 m
(total)
Cable type CAT.5 S-UTP
4 x 2 x AWG 24
Cable type J-Y (ST)
4 x 2 x ø 0.6 mm
< 100 m
(total)
< 350 m
(total)
4 x 2 x AWG 22 4 x 2 x AWG 20
4x2xø
0.8 mm
4x2xø
1.0 mm
*S-UTP (screened unshielded twisted pair)
Do not ground the device.
5.4.1.2 Power supply and data transfer in separate cables
(Local power supply)
Data lines and power supply lines are carried with one of each in a cable.
Power is supplied locally, e.g. from a power supply unit.
A local power supply can be used in the following cases:
•
in long data lines
•
if there are increased requirements regarding the operational safety of the device (offline capability).
Permissible Cable Lengths and Cable Types
Data line RS-485
Type of wiring:
Max. cable length:
Star
Bus
< 100 m
(per stub)
< 1200 m
(total)
Power supply
< 10 m
Cable type CAT.5 S-UTP *
2 x 2 x AWG 24
1 x 2 x AWG 24
Cable type J-Y (ST)
2 x 2 x ø 0.6 mm
1 x 2 x ø 0.6 mm
*S-UTP (screened unshielded twisted pair)
The device may only be supplied with SELV (Safety Extra Low Voltage) and LPS (Limited Power Source), according to IEC/UL/CSA 60950-1.
54
04045708 - 04/2016
Kaba Remote Reader 91 25-AM (US/
CAN)
Technical Manual
5.4.2
Installation
Data line RS-485
Only connect the terminals when the power is switched off.
The device is connected to the host control device via a two-wire party line connection (RS-485).
For information on permissible cable lengths and cable types, please see:
•
•
5.4.2.1 Cable
NOTICE
Local legal provisions (e.g., VDE) must be observed during installation of components.
For notes on structured cabling, see the standard EN 50173.
The cables recommended in the chapter have a foil screen and are designed based
on S-UTP (screened unshielded twisted pair). The wire pairs are not individually
shielded against each other (unshielded). Each pair comprises two color-coded wires
that are twisted together (twisted pair).
NOTICE
It must be ensured that the screen is applied with the aid of the drain wire. The drain
wire must be insulated to avoid short circuits on the circuit boards of the connected
devices using a shrink-on tube or similar.
5.4.2.2 Connection RS-485
Lines A and B are arranged as a twisted wire pair.
Lines A and B must not be crossed.
RS-485
RS-485
Host control device
Kaba remote reader 91 25
Connecting shielding
1. On the host device connect the shielding of the RS-485 cable (blue) to the
ground.
Do not ground the Kaba remote reader 91 25.
2. Connect all shieldings pertaining to the RS-485 cables used (blue) to each other.
Kaba Remote Reader 91 25-AM (US/
CAN)
04045708 - 04/2016
55
Installation
Technical Manual
5.4.2.3 Using several remote readers
If several Kaba remote reader 91 25 are to be connected to a host control device, either bus wiring or star wiring can be used.
See:
•
Star wiring
•
Bus wiring
5.4.2.4 Star wiring
Max. eight devices can be operated on a party line.
Power supply and data line in one cable: Maximum cable length per remote reader or
stub: 20 m
Power supply and data line in separate cables: Maximum data line length per remote
reader or stub: 100 m
120 Ω
RS-485
4,7kΩ
4,7kΩ
4,7kΩ
4,7kΩ
4,7kΩ
Host control device (Kaba access manager)
Distributor (e.g. screw terminal)
Kaba remote reader 91 25
See also
Connection RS-485 [} 5.4.2.2]
Set RS-485 termination resistances
Set peripheral addresses [} 5.7.4]
56
04045708 - 04/2016
Kaba Remote Reader 91 25-AM (US/
CAN)
Technical Manual
Installation
5.4.2.5 Bus wiring
A maximum of eight devices can be operated on a party line.
Maximum total length of data lines (incl. stubs): 1200 m
A stub itself may be a maximum of 100 m in length.
The length of the party line can be increased using a repeater.
5.4.2.5.1 Bus wiring with 1 bus
120 Ω
RS-485
OPEN
OPEN
OPEN
OPEN
120Ω 3
Host control device (Kaba access manager)
Kaba remote reader 91 25
Terminating resistors
See also
Connection RS-485 [} 5.4.2.2]
Set RS-485 termination resistances
Set peripheral addresses [} 5.7.4]
5.4.2.5.2 Bus wiring with two buses
OPEN
RS-485
120Ω
OPEN
RS-485
OPEN
OPEN
OPEN
OPEN
120Ω
Host control device (Kaba access manager)
Kaba remote reader 91 25
Terminating resistors
See also
Connection RS-485 [} 5.4.2.2]
Set RS-485 termination resistances
Set peripheral addresses [} 5.7.4]
5.4.3
Line to the door opener and door contacts
Line requirements: Cable diameters from 0.5 mm to 0.8 mm.
Recommended cable: CAT.5 S-UTP 4 x 2 AWG 24 or AWG 22 (according to EIA/
TIA568) or higher.
Kaba Remote Reader 91 25-AM (US/
CAN)
04045708 - 04/2016
57
Installation
5.4.4
Technical Manual
Coaxial Cable to the Registration Units
Coaxial cable 50 Ohm, item No. 161.250
Cable Type
RG174/U
Maximum cable lengths:
Cable type RG174: up to 30 m
Cable type RG178/U: up to 30 m (RU 90 02: up to 10 m)
Recommended ca- < 10 m
ble length
Max. cable length 30 m
5.4.5
58
RS-232 Connection
Cable type CAT.5 SUTP
2 x 2 x AWG 24
Cable type J-Y (ST)
2 x 2 x 0.6 mm
Max. cable length
15 m
04045708 - 04/2016
Kaba Remote Reader 91 25-AM (US/
CAN)
Technical Manual
5.4.6
Installation
Grounding Concept
5.4.6.1 Power supply
The divice is in a plastic housing and is not grounded.
The power supply can be operated floating or grounded.
5.4.6.2 Communication lines
1. On the host control device connect the shielding of the RS-485 cable (blue) to
the ground.
Do not ground the Kaba remote reader 91 25.
RS-485
RS-485
Host control device
Kaba remote reader 91 25
1. Connect all shieldings pertaining to the RS-485 cables used (blue) to each other.
5.4.6.3 RS-232 Connection
The RS-232 connection lines are not electrically isolated.
Measures to reduce faults:
•
Use shielded cables.
•
Connect the shield to the 0 V line (ground) of the RS-232 connection.
5.4.6.4 Coaxial Cable Terminal
NOTICE
Inner conductor A+ and shield AS of the coaxial cable may be connected to the
ground.
Kaba Remote Reader 91 25-AM (US/
CAN)
04045708 - 04/2016
59
Installation
5.5
Technical Manual
Mounting the device and extension modules
Mount the device on a 35 mm DIN rail (EN 50022).
1. Install the rail.
2. Screw grounding terminal to the rail.
Click
2.
1.
Push
3. Hang the device on the bottom of the DIN rail – without tilting – and press it upwards and keep it pressed.
4. Press the device upwards against the rail at the same time until it can be hung on
the rail.
Connecting extension modules
NOTICE
Attaching live extension modules may cause damage to the devices.
Always switch off the power supply before attaching the extension modules.
1.
2.
Kaba remote reader 91 25
Extension module 90 30
Extension module 90 31
1. Firstly, carefully insert all extension modules 90 30 into the device (1) or an extension module 90 30 (push the devices together on the rail).
ð All extension modules 90 30 are inserted.
2. Then insert extension modules 90 31.
ð The extension module 90 31 which is closer to the device (1) is designated as
module 1. The next module is designated as module 2.
60
04045708 - 04/2016
Kaba Remote Reader 91 25-AM (US/
CAN)
Technical Manual
Installation
Removing extension modules
NOTICE
Removing live extension modules may cause damage to the devices.
Always switch off the power supply before removing the extension modules.
1.
2.
1. Push the extension module away from the adjacent module until the contact is
fully disconnected.
2. Remove the disconnected extension module from the rail.
Kaba Remote Reader 91 25-AM (US/
CAN)
04045708 - 04/2016
61
Installation
5.6
Technical Manual
Connections
Only connect the terminals when the power is switched off.
RS-232 B
16
RS-232 A
Ant. B
3456
91 25
A+
IN3
IN4
OUT1
1. Push
0-F
OUT2
11
OUT3
10
VsVs+
Supply 10-34VDC
VsVs+
OUT3
Output max. 34VDC/27VAC/2A
OUT2
OUT1
GND
IN2
GND
IN3
Input max. 5VDC
GND
IN1
GND
GND
Relay Output Class II
IN5/TP
BCD
Address
RS-485
12
62
IN1
789A
EF012
14
2.
IN2
91 25
Function
8 Service
ON
OFF
IN4
BCD
Mode
13
Click
0-F
DIN-Rail
789A
EF012
3456
Ant. A
State
Prog.
15
A+
AS
AS
0V
Rx
Tx
5V
5V
Rx
Tx
0V
17
Item
Connection/switch
Remark
RS-232 interface B
Connection of peripherals
RS-232 interface A
Antenna B
Registration unit B (antenna B)
Antenna A
Registration unit A (antenna A)
LED Displays
Interface for Extension Modules
Power supply 10–34 VDC
Relay outputs OUT1–OUT3
Inputs IN1–IN4
10
Tamper switch
11
RS-485 interfaces A, B and C
Connection to the host system
12
Bus termination RS-485
Jumper for adjustment of the
termination resistance
13
Addressing RS-485, 1–8
Rotary switch for selecting the
address
14
Function
DIP switch for selecting the
function
15
Operating modes
'Mode' rotary switch for selecting the operating mode
16
Interface for Kaba programmer PD 1460
17
Not used
04045708 - 04/2016
e.g. 90 30/90 31
Kaba Remote Reader 91 25-AM (US/
CAN)
Technical Manual
Installation
The functions and connections of the interfaces, inputs, relay outputs, rotary and DIP
switches are described in the chapter Connecting.
5.6.1
Connections, General
Only connect the terminals when the power is switched off.
5.6.2
Connection Type
Connection Occupancy
Pluggable screw terminals
The occupancy of the connection terminals can be taken from the following tables
Power Supply
2 x 2 clamps are available for the power supply. These are connected in parallel.
Terminal
Meaning
Supply Vs+
10–34 VDC Current consumption max. 330 mA, without
external wiring
Supply Vs-
0 VDC
Supply voltage for
RS-232 and extension
modules at 25°C
5 VDC, max. 1 A
The device may only be supplied with SELV (Safety Extra Low Voltage) and LPS (Limited Power Source), according to IEC/UL/CSA 60950-1.
5.6.3
RS-485 interface
The device communicates with the host system (access hub) via the RS-485 interface.
Terminal
Meaning
RS-485 wire A
RS-485 wire B
RS-485 wire C (Common)
Set RS-485 termination resistances
Set peripheral addresses [} 5.7.4]
5.6.4
'Ant. A' and 'Ant. B' Connections
The connections 'Ant. A' and 'Ant. B' are for the connection of the registration units to
the device. Coaxial cables are used for the connection. LED and acoustic signal transmitter of the registration unit are controlled via the coaxial cable.
Terminal
Meaning
A+
Antenna cable inner conductor
AS
Antenna cable shield wire
Kaba Remote Reader 91 25-AM (US/
CAN)
04045708 - 04/2016
63
Installation
5.6.5
Technical Manual
RS-232 A and RS-232 B Interfaces
The required power supply is provided via the Kaba remote reader 91 25.
Terminal
Meaning
5V
5 VDC
Rx
RXD (Receive/in)
Tx
TXD (Transmit/out)
0V
0V
Further information about the system-dependent functions:
•
5.6.6
System documentation
Programming Interface
For connecting the Kaba programmer.
Usage:
•
5.6.7
Firmware update, see Chapter Firmware Update/LEGIC OS Update
Interface for Extension Modules
For the connection of:
•
Kaba extension module 90 30
•
Kaba extension module 90 31
Number of Supported Extension Modules [} 3.5.1]
Also see about this
2 3.5.1 Number of Supported Extension Modules [} 18]
64
04045708 - 04/2016
Kaba Remote Reader 91 25-AM (US/
CAN)
Technical Manual
5.6.8
Installation
Inputs IN1 – IN4, tamper and input 5
NOTICE
Connecting Isolated Inputs.
The logic (normally open/normally closed) of the inputs can be changed by the host
system.
If the Kaba remote reader 91 25 needs to behave in the same way in both online and
offline operation, the inputs and relay outputs must be connected according to the
operating mode and configured with the DIP switches.
IN1 and IN4 can, when necessary, be used as line-monitored inputs.
5.6.8.1 Inputs IN1 – IN4 (Without Line Monitoring)
If no inputs with line monitoring are used, no additional resistors need to be connected.
Internal wiring without line monitoring
Kaba Remote Reader 91 25-AM (US/
CAN)
04045708 - 04/2016
65
Installation
Technical Manual
5.6.8.2 Inputs IN1 – IN4 With Line Monitoring
Any tampering with the lines between the Kaba remote reader 91 25 and, for example, the door frame contact is detected.
1. Activate/deactivate line monitoring:
Activate or deactivate line monitoring for each input on the host system.
2. Inputs with line monitoring:
Attach resistors (R=680 Ω, ¼ W 2%), ensuring they are tamper-proof.
+5 V DC
680 Ω
IN1-IN4
680 Ω
680 Ω
GND
Kaba remote reader 91 25
Tamper-proof area
3. Using inputs with and without line monitoring at the same time:
No resistors need to be connected to lines without line monitoring.
66
04045708 - 04/2016
Kaba Remote Reader 91 25-AM (US/
CAN)
Technical Manual
Installation
5.6.8.3 Input Tamper
The input tamper is connected as a line-monitored input. Its logical status is enabled
open. If the Kaba remote reader 91 25 is offline and the tamper enabled, this event is
entered in the logbook of the Kaba remote reader 91 25.
5.6.8.4 Input IN5 (only in the Kaba exos lock operating mode)
Input 5 is an internal input for the door handle contact of the Kaba exos lock. The signal is transferred via the coaxial cable and evaluated in the Kaba remote reader 91 25
as input 5.
5.6.9
Output OUT1 – OUT3
Usage e.g.:
•
Kaba Remote Reader 91 25-AM (US/
CAN)
electric strike
04045708 - 04/2016
67
Installation
Technical Manual
5.7
Configuring
5.7.1
Configuration process
1. Set address of the Kaba remote reader 91 25, see chapter
Addressing.
Note down the address. It is required for the configuration in the host system.
2. Set termination resistance on the RS-485 bus as per the bus topology, see chapter
Bus termination RS-485
3. Set operating mode according to the door configuration, see chapter
Set Operating Mode
4. Set extended functions for the selected operating mode, see chapter
Extended functions of the operating modes [} 5.7.6.1]
5. Activate or deactivate monitoring of all inputs, see chapter
Activate monitoring of all inputs (DIP switch 7)
5.7.2
Change Settings
Jumper, DIP switch and rotary switch settings must only be made when the power is
switched off.
Changes of jumper-, DIP switch- and rotary switch settings are only activated after
turning on the power supply (cold start).
RS-232 B
16
RS-232 A
Ant. B
0-F
3456
91 25
DIN-Rail
A+
IN3
IN4
OUT1
1. Push
0-F
OUT2
11
OUT3
10
04045708 - 04/2016
Supply 10-34VDC
VsVs+
OUT3
Output max. 34VDC/27VAC/2A
OUT2
GND
IN2
GND
IN3
GND
IN1
GND
GND
IN5/TP
Relay Output Class II
Input max. 5VDC
VsVs+
Address
RS-485
BCD
12
68
IN1
789A
EF012
14
2.
IN2
91 25
Function
8 Service
ON
OFF
OUT1
BCD
Mode
13
Click
IN4
EF012
789A
15
Ant. A
State
Prog.
3456
A+
AS
AS
0V
Rx
Tx
5V
5V
Rx
Tx
0V
17
Kaba Remote Reader 91 25-AM (US/
CAN)
Technical Manual
5.7.3
Installation
Set RS-485 termination resistances
The connection architecture determines the terminating resistors.
Star wiring
120 Ω
RS-485
4,7kΩ
4,7kΩ
4,7kΩ
4,7kΩ
4,7kΩ
Host control device (Kaba access manager AM)
Distributor (e.g. screw terminal)
Terminating resistors Kaba remote reader 91 25
1. Set the terminating resistor to 4.7 kΩ on the Kaba remote reader 91 25 using the
jumper (12).
2. Set the terminating resistor to 120 Ω on the host control system (1).
Bus wiring with 1 bus
120 Ω
RS-485
OPEN
OPEN
OPEN
OPEN
120Ω 3
Host control device (Kaba access manager AM)
Kaba remote reader 91 25
Terminating resistors
1. Set the terminating resistor to 120 Ω on the last Kaba remote reader 91 25 of the
bus wiring.
2. Set the terminating resistor to open on all other Kaba remote reader 91 25 of the
bus wiring.
Kaba Remote Reader 91 25-AM (US/
CAN)
04045708 - 04/2016
69
Installation
Technical Manual
3. Set the terminating resistor to 120 Ω on the host control system.
Bus wiring with two buses
OPEN
RS-485
120Ω
OPEN
RS-485
OPEN
OPEN
OPEN
OPEN
120Ω
Host control device (Kaba access manager AM)
Kaba remote reader 91 25
Terminating resistors
1. Set the terminating resistor to 120 Ω on both terminal devices of the bus wiring.
2. Set the terminating resistor to open on all other Kaba remote reader 91 25 of the
bus wiring.
3. Set the terminating resistor to open on the host control system.
70
04045708 - 04/2016
Kaba Remote Reader 91 25-AM (US/
CAN)
Technical Manual
5.7.4
Installation
Set peripheral addresses
Each device connected to an RS-485 bus must have a unique address.
1. Assign the Kaba remote reader 91 25 with rotary switch (13) a unique peripheral
address.
5.7.5
Position
Peripheral address
Position
Peripheral address
Default, not used
9–F
Not used
Set Operating Mode
The door configuration determines the operating mode of the Kaba remote reader
91 25.
The operating mode is set with the rotary switch (15).
In order to define the offline behavior of the device, the "extended functions" must
be set in addition to the operating mode. The Chapter [} 5.7.6.1] explains the extended functions.
Kaba remote reader 91 25
Position
Rotary switch
Operating mode
Electric strike
Motor bolt
Automatic door
Turnstile
Night lock
Kaba exos lock
Cylinder interface LI-EL
Motor bolt with panic function
Motor bolt type II with panic function (2
outputs)
Motor bolt type III with panic function (1
output)
Electric lock with panic function
Automatic door with night lock
C–E
Not used
Online operation
The chapter Operating modes [} 4.9] describes the operating modes.
Kaba Remote Reader 91 25-AM (US/
CAN)
04045708 - 04/2016
71
Installation
5.7.6
Technical Manual
Set functions
The following functions can be set with the DIP switches (14):
DIP switch
Number
Function
1–6
Extended functions (according to operating modes)
Not used
ON
Service mode
5.7.6.1 Extended functions of the operating modes
The DIP switches 1–6 (14) are used to set the extended functions of the operating
modes.
The chapter Operating modes describes the operating modes.
If the Kaba remote reader 91 25 needs to behave in the same way in both online and
offline operation, the inputs and relay outputs must be connected according to the
operating mode and configured with the DIP switches.
The parameterization of the access point must match the selected configuration in
the host system. See also chapter Operating Types [} 4.8]
NOTICE
The DIP switches should only be put to ON if the relevant component is also connected to the device.
The following chapters describe the individual operating modes with their connections and configurations.
72
04045708 - 04/2016
Kaba Remote Reader 91 25-AM (US/
CAN)
Technical Manual
Installation
5.7.6.1.1 Operating Mode 0; Electric Strike
Access point
Designation
Connection/function
DIP switch
ON
Outside
Ant. A
Registration unit A
RS-232 A
Optional
Ant. A
Hold-open mode
DIP 2
OUT1
Electric strike
OUT2
Authorized access
DIP 1
IN2
Frame contact
DIP 4
IN3
Blocking contact
DIP 5
OUT3
Alarm buzzer
DIP 6
Ant. B
Registration unit B
RS-232 B
Optional
IN1
Door opener key
DIP 3
IN4
Freely available (only online)
Access point
Designation
Connection/function
DIP switch
ON
Outside
Ant. A
Registration unit A
RS-232 A
Optional
Ant. A
Hold-open mode
DIP 2
OUT1
Motor bolt
IN4
Deadbolt contact (locked)
OUT2
Authorized access
DIP 1
IN2
Frame contact
DIP 4
IN3
Blocking contact
DIP 5
OUT3
Alarm buzzer
DIP 6
Ant. B
Registration unit B
RS-232 B
Optional
IN1
Door opener key
DIP 3
Access point
Designation
Connection/function
DIP switch
ON
Outside
Ant. A
Registration unit A
RS-232 A
Optional
OUT1
Enable pulse for automatic
door
OUT2
Authorized access
DIP 1
IN2
Frame contact
DIP 4
IN3
Blocking contact
DIP 5
OUT3
Alarm buzzer
DIP 6
Door
Inside
5.7.6.1.2 Operating Mode 1; Motor Bolt
Door
Inside
5.7.6.1.3 Operating Mode 2; Automatic Doors
Door
Kaba Remote Reader 91 25-AM (US/
CAN)
04045708 - 04/2016
73
Installation
Technical Manual
Access point
Designation
Connection/function
DIP switch
ON
Inside
Ant. B
Registration unit B
RS-232 B
Optional
IN1
Door opener key
DIP 3
IN4
Freely available
74
04045708 - 04/2016
Kaba Remote Reader 91 25-AM (US/
CAN)
Technical Manual
Installation
5.7.6.1.4 Operating Mode 3; Turnstile
Access point
Designation
Connection/function
DIP switch
ON
Outside
Ant. A
Registration unit A
RS-232 A
Optional
OUT1
Direction-dependent enable pulse
OUT2
Authorized access
DIP 1
IN2
Frame contact
DIP 4
IN3
Blocking contact
DIP 5
Ant. B
Registration unit B
RS-232 B
Optional
OUT3
Direction-dependent enable pulse
IN1
Door opener key
DIP 3
IN4
Freely available
Access point
Designation
Connection/function
DIP switch
ON
Outside
Ant. A
Registration unit A
RS-232 A
Optional
Ant. A
Hold-open mode
DIP 2
OUT1
Electric strike
OUT3
Motor bolt
IN4
Deadbolt contact
OUT2
Authorized access
DIP 1
IN2
Frame contact
DIP 4
IN3
Blocking contact
DIP 5
Ant. B
Registration unit B
RS-232 B
Optional
IN1
Door opener key
DIP 3
Door
Inside
5.7.6.1.5 Operating Mode 4; Night Lock
Door
Inside
Kaba Remote Reader 91 25-AM (US/
CAN)
04045708 - 04/2016
75
Installation
Technical Manual
5.7.6.1.6 Operating Mode 7; Motor Bolt with Panic Function
Access point
Designation
Connection/function
DIP switch
ON
Outside
Ant. A
Registration unit A
RS-232 A
Optional
Ant. A
Hold-open mode
DIP 2
OUT1
Motor bolt
IN4
Deadbolt contact (locked)
OUT2
Authorized access
DIP 1
IN2
Frame contact
DIP 4
IN3
Blocking contact
DIP 5
OUT3
Alarm buzzer
DIP 6
Ant. B
Registration unit B
RS-232 B
Optional
IN1
Door handle contact
DIP 3
Door
Inside
5.7.6.1.7 Operating Mode 8; Motor bolt type II with panic function (2 outputs)
Access point
Designation
Connection/function
DIP switch
ON
Outside
Ant. A
Registration unit A
RS-232 A
Optional
Ant. A
Hold-open mode
DIP 2
OUT1
Lock motor bolt
OUT3
Unlock motor bolt
IN4
Deadbolt contact (locked)
OUT2
Authorized access
DIP 1
IN2
Frame contact
DIP 4
IN3
Blocking contact
DIP 5
Ant. B
Registration unit B
RS-232 B
Optional
IN1
Door handle contact
DIP 3
Door
Inside
76
04045708 - 04/2016
Kaba Remote Reader 91 25-AM (US/
CAN)
Technical Manual
Installation
5.7.6.1.8 Operating Mode 9; Motor bolt type III with panic function (1 output)
Access point
Designation
Connection/function
DIP switch
ON
Outside
Ant. A
Registration unit A
RS-232 A
Optional
Ant. A
Hold-open mode
DIP 2
OUT1
Motor bolt
IN4
Deadbolt contact (locked)
OUT2
Authorized access
DIP 1
IN2
Frame contact
DIP 4
IN3
Blocking contact
DIP 5
OUT3
Alarm buzzer
DIP 6
Ant. B
Registration unit B
RS-232 B
Optional
IN1
Door handle contact
DIP 3
Door
Inside
Kaba Remote Reader 91 25-AM (US/
CAN)
04045708 - 04/2016
77
Installation
Technical Manual
5.7.6.1.9 Operating Mode A; Electric Lock with Panic Function
Access point
Designation
Connection/function
DIP switch
ON
Outside
Ant. A
Registration unit A
RS-232 A
Optional
Ant. A
Hold-open mode
DIP 2
OUT1
Electric lock
IN4
Deadbolt contact (locked)
OUT2
Authorized access
DIP 1
IN2
Frame contact
DIP 4
IN3
Blocking contact
DIP 5
OUT3
Alarm buzzer
DIP 6
Ant. B
Registration unit B
RS-232 B
Optional
IN1
Door handle contact
DIP 3 off
IN1
Door opener key
DIP 3 on
Door
Inside
5.7.6.1.1 Operating Mode B; Automatic Door with Night Lock
Access point
Designation
Connection/function
DIP switch
ON
Outside
Ant. A
Registration unit A
RS-232 A
Optional
Ant. A
Hold-open mode
DIP 2
OUT1
Enable pulse for automatic
door
OUT3
Motor bolt
IN4
Deadbolt contact
OUT2
Authorized access
DIP 1
IN2
Frame contact
DIP 4
IN3
Blocking contact
DIP 5
Ant. B
Registration unit B
RS-232 B
Optional
IN1
Door opener key
DIP 3
Door
Inside
5.7.6.2 Hold-open mode (DIP switch 2)
In hold-open mode, the door remains open upon an authorized access (identification) for as long as the badge remains within range of the antenna (field). The holdopen mode only works without PIN entry. Kaba exos lock and cylinder interface LI-EL
are not supported.
•
78
Hold-open mode applies for antenna A and antenna B
04045708 - 04/2016
Kaba Remote Reader 91 25-AM (US/
CAN)
Technical Manual
Installation
5.7.6.3 Activate the monitoring of inputs
Line monitoring can only be activated and deactivated by the host system.
The position of DIP switch 7 does not affect line monitoring.
5.7.6.4 Service mode (DIP switch 8)
Service mode is only used for service, e.g. for
•
commissioning Hyper X
•
Reset Kaba remote reader 91 25 to the basic status, see Chapter
DIP switch 8 activates service mode.
DIP switch position
Meaning
ON
Service mode activated
OFF
Service mode deactivated
If the device is in service mode, then the access point is blocked and no configuration data will be accepted.
Kaba Remote Reader 91 25-AM (US/
CAN)
04045708 - 04/2016
79
Start-up
Technical Manual
Start-up
6.1
Putting into operation process
ü The device is installed.
Installation process [} 5.1]
ü The device is configured.
Configuring
1. Reset device to its basic state.
Factory Reset/Reset Device to the Basic Status
2. Connect the power supply to the Kaba remote reader 91 25, see chapter
Power Supply [} 5.6.2]
ð LED state illuminates green – LED state flashes green as soon as the RS-485
interface is in the receive or send mode (online).
3. Put the device into operation in accordance with the following chapter.
6.2
"Standalone Access Control without Host System" Commissioning
(Construction site mode)
The Remote reader can already be used on a host system even before connection.
This allows for the use of the remote reader, e.g., during the construction phase.
By connecting the remote reader to a host control device (host system), the functions of the remote reader described in this chapter are replaced by parameterization of the system.
Also see about this
2 1.4 Supplementary Documents [} 8]
6.2.1
Using LEGIC
If using "Standalone access control (without host system)", only the LEGIC stamp
(segment search key) is checked. To authorize access, the user medium's stamp must
match the stamp of the remote reader.
•
If using "Standalone access control (without host system)" the remote reader can
only be used with one stamp (segment search key).
Preparation
1. Use security card C1 (IAM) to define the stamp of master A (only LEGIC ISO
14443A) (see RM_LEGIC_advant_Media_Definition).
Putting into operation
1. Carry out factory reset on the remote reader, see Chapter
2. Present Master A (only LEGIC ISO 14443A) to the connected registration unit.
ð In the event of successful transfer of the stamp: 3x short beep
ð The stamp (segment search key) was transferred onto the remote reader.
ð The remote reader is now ready for bookings.
Functions
•
Book
•
Save the following events (max. 2000):
–
80
Door forced open
04045708 - 04/2016
Kaba Remote Reader 91 25-AM (US/
CAN)
Technical Manual
Start-up
•
–
Doors opened using the button/door handle
–
Door open too long
Not saved:
–
Access events
–
The time and date stamps are incorrect/invalid because the clock on the remote reader has not been set yet.
Book
1. Present a LEGIC user medium (LEGIC prime, ISO 14443A or ISO 15693) to the connected registration unit.
ð If the stamp (segment search key) of the remote reader matches a stamp of
the user medium: Access authorized
Connection to the host control device (host system)
After connecting the remote reader to the host control device (host system), the
saved events are sent to the control device. The time and date stamps are not correct/invalid because the clock of the remote reader had not yet been set (at the time
the events were saved).
6.2.2
Using MIFARE
If using "Standalone access control (without host system)", only the site key/fabrication key is checked. During the check, the medium's fabrication key is not replaced.
To authorize access, the user medium's site key must match one of the remote
reader's site keys.
•
A security card C, a master A, or a master B medium can contain up to eight site
keys.
•
On the medium, the site key's identification file must match the "default ARIOS
configuration"; the application ID, file ID, and coding of the identification number
must match. Media with changed application IDs or non-standard identification
number coding will not be recognized.
Putting into operation
1. Carry out factory reset on the remote reader, see Chapter
2. Hold security card C, a master A or a master B medium in front of the connected
registration unit.
ð In the event of successful transfer of the stamp: 3x short beep
ð A maximum of eight site keys are transferred onto the remote reader.
ð The remote reader is now ready for bookings.
Functions
•
Book
•
Save the following events (max. 2000):
•
Kaba Remote Reader 91 25-AM (US/
CAN)
–
Door forced open
–
Doors opened using the button/door handle
–
Door open too long
Not saved:
–
Access events
–
The time and date stamps are incorrect/invalid because the clock on the remote reader has not been set yet.
04045708 - 04/2016
81
Start-up
Technical Manual
Book
1. Present a MIFARE user medium (MIFARE DESFire or MIFARE Classic) to the connected registration unit.
ð If the user medium's site key matches one of the remote reader's site keys:
Access authorized
Connection to the host control device (host system)
After connecting the remote reader to the host control device (host system), the
saved events are sent to the control device. The time and date stamps are not correct/invalid because the clock of the remote reader had not yet been set (at the time
the events were saved).
82
04045708 - 04/2016
Kaba Remote Reader 91 25-AM (US/
CAN)
Technical Manual
6.3
Start-up
Functional Test (RS-232 A/B)
Requirements
•
Remote reader is installed and connected, see Chapter Installing and Connecting
•
Remote reader is configured, see Chapter Configuring
•
Remote reader is parameterized, see Chapter Parameterizing
•
Remote reader is connected to the power supply, see Chapter Connect Power
Supply
Functions
If the requirements listed above are met, then the parent control unit informs the remote reader which units are connected to the RS-232 interface. The remote reader
communicates with the connected units according to the settings. The remote
reader stores the settings of the connected units. The Chapter Factory Reset/Reset
Device to the Basic Status describes the deletion of this stored settings.
Commissioning Hyper X
•
Kaba Remote Reader 91 25-AM (US/
CAN)
For the commissioning of a Hyper X, the distributor code must be scanned with a
booking in service mode.
04045708 - 04/2016
83
Start-up
6.4
Technical Manual
Issue Write/Read Authorization (Launch)
A write/read authorization is required in the following cases:
•
If the Remote reader needs to write on a write-protected segment of a medium,
e.g. in the case of CardLink applications, validate write-protected CardLink segments
•
If the Remote reader needs to read a read-protected segment of a medium
In this chapter, the term "Write authorization" will be used for the terms "Write authorization" and "Read authorization".
Write authorization with a LEGIC prime SAM 63 card is only valid for LEGIC prime.
Write authorization with a LEGIC advant SAM 63 card is only valid for LEGIC prime
and LEGIC advant 15693 and 14443A.
In this chapter, the designation "Security card C2" will be used for the card designations "SAM 63" and "Security card C2 (SC-C2)".
The signaling is carried via the registration unit on which the card is presented.
Requirement
•
For the write authorization, a security card C2 with corresponding segment area
is required.
•
ISO standard 14443A must have been activated using security card C2.
•
The ISO standard of the SAM 63 card must match the parameterized ISO standard.
•
The device should be in regular operation and waiting for an RFID entry.
Procedure
1. Present the security card C2 to the connected registration unit without interruption (approx. 15 s).
ð The Registration unit illuminates green during the process.
ð Signaling after successful write authorization: 3x beeps
If the Remote reader has previously been granted write authorization using
the same security card C2, this will be signaled immediately by 3x beeps
No indications are made on the exos lock or cylinder interface LI-EL following
successful write authorization.
ð No signaling: Write authorization has not been granted.
Possible reasons
- The security card C2 was removed from the RFID field too early
- ISO 14443A is not activated in the system
- If SAM+ media are being used: No credit is available
2. Remove the security card C2 from the field.
84
04045708 - 04/2016
Kaba Remote Reader 91 25-AM (US/
CAN)
Technical Manual
6.5
Start-up
Cancel Write/Read Authorization
The write/read authorization needs to be canceled in the following cases:
•
If the Remote reader no longer needs to write on write-protected segments of a
medium
•
If the Remote reader no longer needs to read read-protected segments of a
medium
In this chapter, the term "Write authorization" will be used for the terms "Write authorization" and "Read authorization".
In this chapter, the term "Writing right" will be used for the terms "Writing right" and
"Reading right".
6.5.1
Cancel all writing rights granted by a write authorization
1. Reset remote reader to the basic status, see Chapter
6.5.2
Cancel a particular writing right granted by a write authorization:
Use the SAM 64 card to delete the relevant stamp.
The signaling is carried via the registration unit on which the card is presented.
Requirement
•
In order to cancel the write authorization, a SAM 64 card with the relevant segment range is required.
•
The device is in normal operation and waits for an RFID entry.
Procedure
1. Present the SAM 64 card to the connected registration unit without interruption
(approx. 15 s).
ð The Registration unit illuminates green during the process.
ð Signaling after successful cancellation of the write authorization:
3x Beep
If the write authorization has already previously been canceled with the
same SAM 64 card, this will be signaled immediately with 3x beeps.
ð No signaling: unsuccessful cancellation of write authorization
Possible reasons
- The SAM 64 card was removed from the RFID field too early (no signaling)
- ISO 14443A is not enabled in the system
- If SAM+ media are used: there are no credits available
2. Remove the SAM 64 card from the field.
Kaba Remote Reader 91 25-AM (US/
CAN)
04045708 - 04/2016
85
Servicing
Technical Manual
Servicing
7.1
Programming interface
A 3-pin connection (16) to connect to the Kaba programmer 1460 is located on the
front of the Kaba remote reader 91 25. The connection (16) is used to update the
firmware.
RS-232 B
16
RS-232 A
Ant. B
3456
91 25
DIN-Rail
A+
IN3
IN4
OUT1
1. Push
0-F
OUT2
11
OUT3
10
Supply 10-34VDC
VsVs+
OUT3
Output max. 34VDC/27VAC/2A
OUT2
GND
IN2
GND
IN3
GND
IN1
GND
GND
IN5/TP
Relay Output Class II
Input max. 5VDC
VsVs+
Address
RS-485
BCD
12
7.2
IN1
789A
EF012
14
2.
IN2
91 25
Function
8 Service
ON
OFF
OUT1
BCD
Mode
13
Click
0-F
IN4
EF012
789A
15
Ant. A
State
Prog.
3456
A+
AS
AS
0V
Rx
Tx
5V
5V
Rx
Tx
0V
17
Restart
Consequences of the restart
•
Duration approx. 3 seconds
•
The access point is blocked during the restart.
•
The saved parameter settings and data remain in place.
•
The device is restarted.
1. Switch the power supply off and on again.
ð The LED state goes out.
ð The access point is blocked.
2. After the restart, the LED state changes back to green.
ð Offline mode: If the device is parameterized for offline mode, the access
point is now ready for bookings.
ð Online mode: After the connection has been set up with the host control
device, the remote reader is ready for operation in online mode.
Restarting resets the internal clock. After restarting, the clock will read 01/01/2010
00:00. Logbook entries will be saved with an incorrect date stamp as a result until the
next online operation.
86
04045708 - 04/2016
Kaba Remote Reader 91 25-AM (US/
CAN)
Technical Manual
7.3
Servicing
Service mode
Service mode is part ...
7.3.1
•
of the factory reset
•
of the firmware update
Enable service mode
Procedure
1. Disconnect device from the power supply
ð The access point is blocked while in service mode
2. If the write authorization has to be canceled: set 'Mode' rotary switch to 'F'
3. Set DIP switch 8 to 'ON' (in the event of uninterrupted power supply, a change in
the status of the DIP switch has no effect)
ð Service mode is activated
7.3.2
Disable service mode
Procedure
1. Disconnect device from the power supply
2. Set DIP switch 8 to 'OFF'.
ð Service mode is deactivated
Kaba Remote Reader 91 25-AM (US/
CAN)
04045708 - 04/2016
87
Servicing
7.4
Technical Manual
Factory Reset/Reset Device to the Basic Status
Consequences of the factory reset
•
The device is returned to its basic state (factory settings).
•
The parameter settings are deleted.
•
If the Mode rotary switch is set to F, the write authorization (launch data) will be
deleted.
•
The stamps are deleted.
•
The factory reset lasts approximately 3 seconds.
•
The access point is blocked during the factory reset.
The factory reset is controlled by the following switches:
•
DIP switch for selecting the function, see chapterDevice structure
•
'Mode' rotary switch for selecting the operating mode, see chapter Device structure
Procedure
1.
Signaling
Remote reader
Signaling
Registration unit
Disconnect the device from the power supply.
•
2.
3.
4.
The access point is blocked during the factory reset.
If the write authorization is to be deleted (launch
data): Set 'Mode' rotary switch to F
Set DIP switch 8 to ON.
(Switching the DIP switch when the power supply is
connected has no effect).
• Service mode is activated.
Connect the device to the power supply.
• Device is reset to the factory settings (for further
2 x short beep, then red/
effects, see above, consequences of the factory
green flashing
reset).
State: permanent orange
IN1–IN4: permanent orange
If 'Mode' rotary switch is
set to 'F'*:
OUT1–3: permanent red
5.
6.
7.
8.
9.
88
Wait until the IN LEDs flash orange.
Disconnect the device from the power supply.
Set DIP switch 8 to OFF.
• Service mode is deactivated.
Set the desired operating mode on the 'Mode' rotary
switch.
Connect device to the power supply.
04045708 - 04/2016
Kaba Remote Reader 91 25-AM (US/
CAN)
Technical Manual
Servicing
•
The device is in operation again.
•
In the event of online connection: The host control device loads the current parameters on the
remote reader.
State: permanent green
or flashing green
permanent green
• The access point is ready for bookings.
The write authorization (launch data) is deleted.
Kaba Remote Reader 91 25-AM (US/
CAN)
04045708 - 04/2016
89
Servicing
7.5
Technical Manual
Firmware Update/LEGIC OS Update
An update can be performed in the following ways:
•
Using the access manager service tool via access manager (via Ethernet and the
RS-485 interface)
•
Using the Kaba EAC service tool and programmer 1460
NOTICE
Consequences of the firmware update:
7.5.1
•
Device is reset to the factory settings(basic status)
•
The parameterization is deleted
•
The data is deleted
•
The stamps are deleted
Firmware update/LEGIC OS update via access manager
The firmware/LEGIC OS is updated using the access manager service tool via access
manager (via Ethernet and the RS-485 interface). The access manager reference manual describes the process.
7.5.2
Firmware Update / LEGIC OS Update with programmer 1460
The firmware update/LEGIC OS update lasts around 120 seconds.
Requirements
• The firmware has been transferred from the Kaba EAC service tool to the programmer 1460 (the LEGIC OS is integrated into the firmware).
•
The user is familiar with the handling of the programmer and the Kaba EAC service tool.
•
Kaba EAC service tool ≥ V 2.6.1 is installed.
•
FTDI driver (using the operating system) for Kaba programmer 1460 is installed (FTDI CDM supports D2XX and
VCP functionality) http://www.ftdichip.com/FTDrivers.htm
•
Microsoft .Net Framework 4 Client Profile is installed http://www.microsoft.com/net/
Procedure
1.
Signaling
Registration unit
Disconnect the device from the power
supply.
(Switching DIP switch 8 when the
power supply is connected has no effect.)
•
The access point is blocked during
the firmware update.
2.
Turn DIP switch 8 to ON.
3.
• Service mode is activated.
Connect the device to the power supply.
90
Signaling
Remote reader
04045708 - 04/2016
Kaba Remote Reader 91 25-AM (US/
CAN)
Technical Manual
Servicing
IN1–4 flash orange
2 x short beep, then alternate
red/green flashing
If the programmer is connected If the programmer is connected
before switching on the power before switching on the power
supply, then there is no flashing. supply, then there is no flashing.
4.
Connect the programmer to the device
using the programming cable.
LED off or permanent orange
LED off
NOTICE
During the firmware update, the power supply and the connection to the programmer must not be interrupted.
5.
6.
7.
8.
9.
On the programmer, select the
firmware to be transferred and then
download.
After successful download:
Disconnect the device from the power
supply.
If the programmer is removed
before the power supply is interrupted, then the LEDs flash according to the update mode.
If the programmer is removed
before the power supply is interrupted, then the LEDs flash according to the update mode.
Set DIP switch 8 to OFF.
• Service mode is deactivated.
Disconnect the programmer from the
device.
Connect the device to the power supply.
• The device is in operation again.
•
In the event of online connection:
The host control device loads the
current parameters on the remote
reader.
•
The access point is ready for bookings.
State: permanent green or flash- permanent green
ing green
The settings of the rotary switch (operating modes, addressing) have no influence on
the service mode.
Kaba Remote Reader 91 25-AM (US/
CAN)
04045708 - 04/2016
91
Servicing
7.6
Technical Manual
Crossgrade
A crossgrade can be used to amend the functional type of a device. For example, a
device with the functional type access manager (AM) can be turned into a device
with the functional type AMC.
The process for changing the functional type is described in the user manual for Kaba
programmer 1460, document no k1evo809.
7.6.1
Device with Bxxx firmware (MRD)
Remote reader type before
crossgrade
Remote reader type after
crossgrade
Functional
type
MRD
•
(multi RFID de•
vice)
AM
AMC
Functional
type
Crossgrade
⇨
MRD
•
(multi RFID de•
vice)
AMC
AM
Illustrative example
Only Bxxx firmware (MRD) can be transferred to a device with Bxxx firmware (MRD).
It is possible to change functional type.
It is possible to change between LEGIC and MIFARE.
92
04045708 - 04/2016
Kaba Remote Reader 91 25-AM (US/
CAN)
Technical Manual
Troubleshooting
Troubleshooting
8.1
LED Displays on the Remote Reader
LED desig- LED signaling
nation
State
Meaning
Measures
red permanent •
Incorrect firmware
•
•
Remote reader defective
Carry out firmware update
•
Replace remote reader
flashes green
and orange
After an interruption in
communication, until
the Kaba remote reader
91 25 is queried for the
first time by the host
system
orange perma- Service mode
nent
IN1–IN4
orange perma- Short circuit
nent
Check DIP switch 7 or lines/
resistances, see chapter
5.7.6.2
flashes green
•
Check voltage (Vs)
•
Replace remote reader
(Assignred permanent interruption
ments:
IN5 to IN1
IN6 to IN2)
OUT1–
OUT3
8.2
•
Undervoltage (Vs)
or
•
relay defective
During Installation
Error
Possible cause
Measures
Host system does
not recognize the
remote reader
Communication between remote reader and host system
defective
Check communication using
the LED state and adjust
The address set on the remote Check address settings on the
reader does not match the ad- remote reader and in the host
dress set in the system
system
Kaba Remote Reader 91 25-AM (US/
CAN)
Incorrect termination resistances
Adjust RS-485 termination resistances
Interruption
Check/repair cable and connections
04045708 - 04/2016
93
Troubleshooting
Technical Manual
Error
Possible cause
Measures
Remote reader
Interruption
does not read correctly
Incorrect customer medium
used
Check/repair connection of
registration units
Check whether the correct
customer medium was used
when putting it into operation
Medium does not match the
definition in the system
Check whether the medium
found and its definitions are
parameterized correctly in the
system
Several devices which are con- Give a unique address to each
nected to the RS485 bus have divice which is connected to
the same address
the RS485 bus
8.3
RF standard not parameterized in the host system
Adjust the configuration in the
host system
Error
Possible cause
Measures
Host system does
not recognize or
only temporarily
recognizes the remote reader
Facility changed by user
Adjust facility
During operation
New sources of interference
Reduce influence of the
(e.g. new or replaced hubs,
sources of interference (encash dispensers or other secu- large distance, shielding)
rity systems)
Cabling changed
Adjust cabling
Configuration of the access
point in the host system
changed
Adjust configuration of the access point in the host system
Several devices connected to
the RS-485 bus have the same
address
Assign a unique address to
each device connected to the
RS-485 bus
Remote reader
Facility changed by user
does not read cor- New sources of interference
rectly
(e.g. new or replaced hubs,
cash dispensers or other security systems)
Adjust facility
Reduce influence of the
sources of interference (enlarge distance, shielding)
Cabling changed
Adjust cabling
Incorrect handling of the
medium
Inform user of correct use of
the medium and the registration unit
RF standard not set correctly
Structure of the medium or its Adjust structure of the
structure in the system not
medium or its structure in the
correct
system
94
04045708 - 04/2016
Kaba Remote Reader 91 25-AM (US/
CAN)
Technical Manual
Troubleshooting
Error
Possible cause
Measures
Time-related sequence of the access point control
is incorrect
Configuration of the access
point in the host system
changed
Adjust DIP switch settings
Memory of the remote reader
deleted via factory reset and
the data of the host system
has not yet been written to
the remote reader
Adjust times in the host system and transfer to the remote reader
Check whether the data has
been loaded from the control
device onto the remote reader
after a factory reset
Check whether the desired
times have been defined in
the host system
Remote reader
does not write on
the media
Kaba Remote Reader 91 25-AM (US/
CAN)
Cabling changed
Adjust cabling
Remote reader has no write
authorization
Issue write authorization, see
chapter 6.4
CardLink settings in the host
control device are incorrect
Adjust the configuration of the
host control device
04045708 - 04/2016
95
Packaging/Return
Technical Manual
Packaging/Return
Incorrectly packaged assemblies and devices may cause expenses due to damage
during transport.
Please observe the following information when sending Kaba products.
Kaba shall not be liable for damage to products which can be attributed to insufficient packaging.
9.1
Complete Devices
The original packaging is specially adapted for the device. It offers the greatest possible protection against transport damage.
Always use the original packaging for returns.
If this is not possible, then ensure the packaging prevents damage to the device.
9.2
•
Use a stable, thick-walled transport crate or a box. The transport crate should be
large enough that there is 8–10 cm space between the device and the container
wall.
•
Wrap the device in suitable film or put in a bag.
•
Pad generously around the device e.g. using foam padding or bubble wrap. It
must be ensured that the device does not move within the packaging.
•
Only use dust-free environmentally-friendly filling material.
Electronic Assemblies
Electronic assemblies sensitive to ESD, such as circuit boards, readers, etc., must be
stored, transported and sent in suitable ESD protective packaging. The packaging of
electronic assemblies may only be carried out in ESD-protected workplaces by persons who are familiar with and follow the general ESD protective regulations.
The return of electronic assemblies in packaging with sufficient ESD protection is a
condition for
•
making guarantee claims in the event of malfunctions of any kind.
•
replacement delivery of electronic circuit boards and components when an exchange is provided.
In order to guarantee a high quality standard, electronic components supplied in
packaging without sufficient ESD protection will be neither analyzed nor repaired,
but instead disposed of directly.
9.3
Marking
Complete return papers and correct labeling allow us to process matters quickly.
Please ensure that a delivery note is included with the package. The delivery note
should include the following information:
96
•
Number of devices or components per package.
•
Item numbers, serial numbers, designations.
•
Address of your company/contact.
•
Reason for the return, e.g. repair exchange.
•
Informative description of the fault.
04045708 - 04/2016
Kaba Remote Reader 91 25-AM (US/
CAN)
Technical Manual
Packaging/Return
In the event of returns from outside of the EU, a customs invoice with the real customs value will also be required. In some countries (e.g. Switzerland) a preference will
be required.
Kaba Remote Reader 91 25-AM (US/
CAN)
04045708 - 04/2016
97
Disposal
10
Technical Manual
Disposal
This chapter provides important information on disposal.
10.1
Decommissioning
The following steps should be executed for the decommissioning of the device in an
access control system:
1. For online operation: Check configuration of the host system
2. Disconnect the device from the power supply
3. Disconnect RS-485 connection from the host system
10.2
Dismantling
ü The device has been decommissioned.
1. If available, unplug extension modules
2. Disconnect relay outputs from the device
3. Disconnect inputs from the device
4. Disconnect RS-232 interface and/or keypads, biometrics or system-dependent
functions from the device
5. Disconnect registration units from the device
6. Remove device from the rail
2 Click
Push
10.3
Disposal
This product meets the requirements of the WEEE Directive and, in accordance with
DIN standard EN 50419, is labeled with the WEEE crossed-out garbage can symbol.
The symbol indicates the separate disposal of electric and electronic equipment in
EU countries.
Do not dispose of the device with household waste under any circumstances.
Used devices contain valuable recyclable materials that should be recycled. Used devices should therefore be disposed of via the collection system used in your country.
Disposal in Germany:
After use, Kaba GmbH undertakes to carry out the proper disposal of the supplied
goods in line with legal requirements (such as the ElektroG law in Germany). All costs
incurred for the transport of goods to the manufacturer's plant will be borne by the
owner of the used electronic equipment.
Disposal in Switzerland:
Send the device to an electronic equipment collection facility as per the VREG regulation.
In the EU, electrical devices should be disposed of in accordance with national waste
disposal and environmental directives.
The erasure of personal data before disposal must be carried out self-dependent.
98
04045708 - 04/2016
Kaba Remote Reader 91 25-AM (US/
CAN)
Technical Manual
Disposal
Dispose of packaging in an environmentally-friendly manner.
The packaging materials are recyclable. Please do not put the packaging in with
household waste, instead dispose of with waste for recycling.
Kaba Remote Reader 91 25-AM (US/
CAN)
04045708 - 04/2016
99
Disposal
Technical Manual
Index
CE conformity ............................................................................. 22
Conformity................................................................................... 22
Designated use ..........................................................................
Disposal ........................................................................................
Door contact ...............................................................................
Door frame contact ..................................................................
Door opener................................................................................
11
98
52
52
52
Electromagnetic fields.............................................................
EMC directive..............................................................................
ESD protective measures........................................................
Extension modules ...................................................................
51
22
12
18
Factory reset................................................................................ 88
Firmware update ....................................................................... 90
Grouped safety messages...................................................... 11
Identification plate ................................................................... 24
Installation cables ..................................................................... 52
LED Display............................................................................ 30, 93
LEGIC OS update........................................................................ 90
Low voltage directive .............................................................. 22
Offline Operation ................................................................ 31, 32
Online operation ................................................................. 31, 32
Packaging..................................................................................... 96
Power supply line...................................................................... 53
Programming interface........................................................... 86
R&TTE directive ................................................................
Return............................................................................................
RoHS...............................................................................................
RS-485 bus termination ..........................................................
22
96
22
69
Safety ............................................................................................. 11
Safety messages ........................................................................ 11
Supplementary Documentation............................................. 8
Troubleshooting........................................................................ 93
100
04045708 - 04/2016
Kaba Remote Reader 91 25-AM (US/
CAN)
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf Linearized : No Page Count : 100 Page Mode : UseOutlines PDF Version : 1.4 Title : TM_RemoteReader9125-AM-US-CAN_201603_en Creator : SCHEMA ST4 Producer : ST4 PDF Engine (Build 5.0.2.4) Create Date : 2016:04:26 15:50:55+02:00 Modify Date : 2016:04:26 15:50:55+02:00EXIF Metadata provided by EXIF.tools