dresden elektronik ingenieurtechnik MEGA23M12 Lightport User Manual

dresden elektronik ingenieurtechnik gmbh Lightport Users Manual

Users Manual

4628
23
4626
Quick Installation Guide
LA N
DMX
max 10m.
Connect the Invisua Lightport to your local network
router (with internet access) via the supplied LAN cable.
(Recommended maximum distance Lightport-xtures:
10m. line of sight)
LA N
DMX
Power the Invisua Lightport via the supplied 12V
power supply.
1 2
Check document “Network and Hardware
recommendations” in case the second LED does not light
up. (http://main.invisua.com/en/downloads/)
Verify that the second LED is ON to conrm internet
connection. (Blinking indicates having an IP address
obtained, full ON indicates internet connection)
1
Mount all the Invisua Masterspot 2 Track xtures on
your track.
It is recommended to position the xtures ordered
by serial number. In that way the xture sequence in
Invisua Create will be identical.
Masterspot 2 Track
12 VDC
12 VDC
www.invisua.com
1
23
45
5sec
1 2
Press button #1 on the Lightport for 5 sec. to initiate
commissioning of your system. (lamp indicator LED on the
Lightport will turn ON)
67
Of f
On
Of f
On
Within 30 sec. after pressing button #2, turn the Masterspot
2 Track xtures OFF and ON again, by disconnecting and
reconnecting the 230V power.
1
Please visit www.create.invisua.com (via pc or tablet)
to create your rst light scenes!
(We strongly recommend you to follow the Invisua Create
Tutorial once logged in to make yourself familiar with the
system)
After all xtures have lit up purple, testing your
setup can be done by pressing button #2 on the
Lightport, to toggle between some default light
scenes.
Please wait approx. 2 minutes. All xtures should
light up purple, to conrm that they have been
discovered by the Lightport.
All xtures should turn green for 1 sec and after some
time, give white light. This conrms that the xtures are
on the right unique communication channel.
By going to my.invisua.com, one of the pre-stored light
scenes can be activated. With the color-picker the
xture(s) can be set to any white or RGB color instantly.
(Make sure you are connected to the same network as
the Invisua Lightport)
If not all xtures have turned green for 1 sec
go back to step 6.
If not all xtures have turned purple go back
to step 6, but if step 8 was successful, you can
skip step 7 and 8
2
89
10 11
12
v. 1.02
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. The-
se limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
To assure continued compliance, any changes or modications not expressly approved by the party responsible for compliance could
void the user’s authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or perip-
heral devices).
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
FCC Radiation Exposure Statement:
(if mobile device (generally 20 cm distance) is applicable, MPE calculation)
“This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The antenna(s) used for this
transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating
in conjunction with any other antenna or transmitter”.

Navigation menu