dresden elektronik ingenieurtechnik MEGA23M12 Lightport User Manual

dresden elektronik ingenieurtechnik gmbh Lightport Users Manual

Users Manual

462823 4626 Quick Installation GuideLA NDMXmax 10m.Connect the Invisua Lightport to your local networkrouter (with internet access) via the supplied LAN cable.(Recommended maximum distance Lightport-xtures:10m. line of sight)LA NDMXPower the Invisua Lightport via the supplied 12Vpower supply.1 2Check document “Network and Hardwarerecommendations” in case the second LED does not lightup. (http://main.invisua.com/en/downloads/)Verify that the second LED is ON to conrm internetconnection. (Blinking indicates having an IP addressobtained, full ON indicates internet connection)1Mount all the Invisua Masterspot 2 Track xtures on your track.It is recommended to position the xtures orderedby serial number. In that way the xture sequence inInvisua Create will be identical.Masterspot 2 Track12 VDC12 VDCwww.invisua.com123455sec1 2Press button #1 on the Lightport for 5 sec. to initiate commissioning of your system. (lamp indicator LED on the Lightport will turn ON)67Of fOnOf fOn Within 30 sec. after pressing button #2, turn the Masterspot 2 Track xtures OFF and ON again, by disconnecting and reconnecting the 230V power.
1Please visit www.create.invisua.com (via pc or tablet)to create your rst light scenes! (We strongly recommend you to follow the Invisua Create Tutorial once logged in to make yourself familiar with the system)After all xtures have lit up purple, testing your setup can be done by pressing button #2 on the Lightport, to toggle between some default light scenes.Please wait approx. 2 minutes. All xtures should light up purple, to conrm that they have been discovered by the Lightport.All xtures should turn green for 1 sec and after some time, give white light. This conrms that the xtures are on the right unique communication channel.By going to my.invisua.com, one of the pre-stored light scenes can be activated. With the color-picker the xture(s) can be set to any white or RGB color instantly. (Make sure you are connected to the same network as the Invisua Lightport)If not all xtures have turned green for 1 secgo back to step 6.If not all xtures have turned purple go back to step 6, but if step 8 was successful, you can skip step 7 and 828910 1112v. 1.02FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. The-se limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:Reorient or relocate the receiving antenna.Increase the separation between the equipment and receiver.Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.Consult the dealer or an experienced radio/TV technician for help.To assure continued compliance, any changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or perip-heral devices). This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement:(if mobile device (generally 20 cm distance) is applicable, MPE calculation)“This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter”.

Navigation menu