eInstruction R2 Response Receiver User Manual InterWrite Whiteboards GS A

eInstruction Corporation Response Receiver InterWrite Whiteboards GS A

user manual

Basic Operating InstructionsInterwriteTM Maestro User’s Guide1Enable your Maestro by starting up Interwrite PRS and selectingthe RF, Enable Master Clicker menu option. Click on the EnableMaster Clicker checkbox and enter the Radio ID found on the backof your Maestro in the Master Clicker ID text box.2Turn on Maestro.The green Connect LED will blink fast, indicating the Maestrois ready to join the Class.3Connect to the Class by pressing the two-character code displayedby the Interwrite PRS software.The LED will blink slowly as long as the Maestro is connected tothe Class.4Press a Maestro Command button (see chart below).LED will be green if command was received.LED will be red if command was not received.5Hold down the button until the LED goes off.Maestro Button CommandsStart a new Session This applies only to a PRS Lesson Session.Start Question TimerPause Question TimerResume Question TimerThis applies only to PRS Lesson Sessions.F5 Function Key This is the Function Key used to start aPowerPoint Slide Show.End SessionEnd QuestionThis is the equivalent of clicking on the EndSession button to end a PRS Session, or theEnd Question button to end a PRS PowerPointQuestion Slide.Stop Question TimerGo back to the PreviousQuestionThis can be used only during a PRS LessonSession.Advance to the NextQuestionThis can be used only during a PRS LessonSession.Page Up This is used during a PowerPoint Session to goto the previous slide.Page Down This is used during a PowerPoint Session to goto the next slide.Issue the Tab commandIssue the Enter command This command is used to process the OK anddefault buttons on dialogs.Issue the ESCapecommand
Limited Warranty for Interwrite MaestroInterwrite Learning warrants this product to be free from defects in material and workmanship underthe following terms.CoverageParts and labor are warranted for one (1) year from the date of the first consumer purchase of theInterwrite Maestro.Technical SupportWeb-based Technical Support is available free of charge at: www.interwritelearning.com/support, fortechnical support, Flash tutorials, troubleshooting, Technical Bulletins, and FAQs can be found.Declaration of ConformityThe “CE” mark on this device indicates compliance under the EMC 89//336/EEC Directive. Declarationof conformity according to ISO/IEC Guide 22 and EN 45014Manufacturer’s Name: GTCO Corp.(dba Interwrite Learning)Manufacturer’s Address: 7125 Riverwood DriveColumbia, MD 21046 U.S.A.declares, that the productProduct Name: Interwrite MaestroModel Number: R2conforms to the following product specifications:EMC: EMC Directive 89/336/EEC andamendment 92/31/EECEmissions EN 55022:2003 Class BTesting EN 55024:2003 andLow Voltage Directive 73/23/EECDana Doubrava, Engineering Mgr,Scottsdale, Arizona, U.S.A., 6.1.2007Note: This equipment has been tested and found to comply with the limits of a Class B digital device,pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection againstharmful interference in a residential installation. This equipment generates, uses and can radiate radiofrequency energy and, if not installed and used in accordance with the instructions, may cause harmfulinterference to radio communications. However, there is no guarantee the interference will not occurin a particular installation. If this equipment does cause harmful interference to radio or televisionreception, which can be determined by turning the equipment off and on, the user is encouraged totry to correct the interference by one or more of the following measures.• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and the receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver isconnected.• Consult the dealer or an experienced Radio/TV technician for help.This device complies with Part 15 of FCC rules and with RSS-210 of Industry Canada. Operation issubject to the following two conditions: (1) This device may not cause harmful interference, and (2)this device must accept any interference received, including interference that may cause undesiredoperation. The radiated output power is far below the FCC Radio Frequency exposure limits.Nevertheless, this device should be used in such a manner that the potential for human contact duringnormal operation is minimized. This equipment complies with FCC radiation exposure limits setforth for an uncontrolled environment. End users must follow the specific operating instructions forsatisfying RF exposure compliance. This transmitter must not be co-located or operated inconjunction with any other antenna or transmitter.36-01336-01/37-01176-01 Rev. AEuropean Union Emission DirectiveThis product is in conformity with the protection requirements of EUCouncil Directive 89/366/ECC on the approximation of the laws ofthe Member States relating to electromagnetic compatibility. Thisproduct has been tested and found to comply with the limits forClass B Information Technology Equipment according to CISPR 22/European Standard EN55022. The limits for Class B equipment werederived for typical industrial environments to provide reasonableprotection against interference with licensed communication devices.CanadaIndustry Canada Class B emission compliance statement. This Class Bdigital apparatus complies with Canadian ICES-003.Avis de conformité á la réglementation d’Industrie Canada. Cetappareil numérique de classe B est conforme á la norme NMB-003du Canada.European ContactInterwrite LearningA Division ofGTCO CalComp GmbHKreiller Strasse 2481673 MunichGermanyTel: +49 (0) 89 370012-0Fax: +49 (0) 89 370012-12www.InterwriteLearning.comSupport: 480.443.2214

Navigation menu