eInstruction R2 Response Receiver User Manual InterWrite Whiteboards GS A
eInstruction Corporation Response Receiver InterWrite Whiteboards GS A
user manual
Basic Operating Instructions
InterwriteTM Maestro User’s Guide
1Enable your Maestro by starting up Interwrite PRS and selecting
the RF, Enable Master Clicker menu option. Click on the Enable
Master Clicker checkbox and enter the Radio ID found on the back
of your Maestro in the Master Clicker ID text box.
2Turn on Maestro.
The green Connect LED will blink fast, indicating the Maestro
is ready to join the Class.
3Connect to the Class by pressing the two-character code displayed
by the Interwrite PRS software.
The LED will blink slowly as long as the Maestro is connected to
the Class.
4Press a Maestro Command button (see chart below).
LED will be green if command was received.
LED will be red if command was not received.
5Hold down the button until the LED goes off.
Maestro Button Commands
Start a new Session This applies only to a PRS Lesson Session.
Start Question Timer
Pause Question Timer
Resume Question Timer
This applies only to PRS Lesson Sessions.
F5 Function Key This is the Function Key used to start a
PowerPoint Slide Show.
End Session
End Question
This is the equivalent of clicking on the End
Session button to end a PRS Session, or the
End Question button to end a PRS PowerPoint
Question Slide.
Stop Question Timer
Go back to the Previous
Question
This can be used only during a PRS Lesson
Session.
Advance to the Next
Question
This can be used only during a PRS Lesson
Session.
Page Up This is used during a PowerPoint Session to go
to the previous slide.
Page Down This is used during a PowerPoint Session to go
to the next slide.
Issue the Tab command
Issue the Enter command This command is used to process the OK and
default buttons on dialogs.
Issue the ESCape
command
Limited Warranty for Interwrite Maestro
Interwrite Learning warrants this product to be free from defects in material and workmanship under
the following terms.
Coverage
Parts and labor are warranted for one (1) year from the date of the first consumer purchase of the
Interwrite Maestro.
Technical Support
Web-based Technical Support is available free of charge at: www.interwritelearning.com/support, for
technical support, Flash tutorials, troubleshooting, Technical Bulletins, and FAQs can be found.
Declaration of Conformity
The “CE” mark on this device indicates compliance under the EMC 89//336/EEC Directive. Declaration
of conformity according to ISO/IEC Guide 22 and EN 45014
Manufacturer’s Name: GTCO Corp.
(dba Interwrite Learning)
Manufacturer’s Address: 7125 Riverwood Drive
Columbia, MD 21046
U.S.A.
declares, that the product
Product Name: Interwrite Maestro
Model Number: R2
conforms to the following product specifications:
EMC: EMC Directive 89/336/EEC and
amendment 92/31/EEC
Emissions EN 55022:2003 Class B
Testing EN 55024:2003 and
Low Voltage Directive 73/23/EEC
Dana Doubrava, Engineering Mgr,
Scottsdale, Arizona, U.S.A., 6.1.2007
Note: This equipment has been tested and found to comply with the limits of a Class B digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee the interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced Radio/TV technician for help.
This device complies with Part 15 of FCC rules and with RSS-210 of Industry Canada. Operation is
subject to the following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause undesired
operation. The radiated output power is far below the FCC Radio Frequency exposure limits.
Nevertheless, this device should be used in such a manner that the potential for human contact during
normal operation is minimized. This equipment complies with FCC radiation exposure limits set
forth for an uncontrolled environment. End users must follow the specific operating instructions for
satisfying RF exposure compliance. This transmitter must not be co-located or operated in
conjunction with any other antenna or transmitter.
36-01336-01/37-01176-01 Rev. A
European Union Emission Directive
This product is in conformity with the protection requirements of EU
Council Directive 89/366/ECC on the approximation of the laws of
the Member States relating to electromagnetic compatibility. This
product has been tested and found to comply with the limits for
Class B Information Technology Equipment according to CISPR 22/
European Standard EN55022. The limits for Class B equipment were
derived for typical industrial environments to provide reasonable
protection against interference with licensed communication devices.
Canada
Industry Canada Class B emission compliance statement. This Class B
digital apparatus complies with Canadian ICES-003.
Avis de conformité á la réglementation d’Industrie Canada. Cet
appareil numérique de classe B est conforme á la norme NMB-003
du Canada.
European Contact
Interwrite Learning
A Division of
GTCO CalComp GmbH
Kreiller Strasse 24
81673 Munich
Germany
Tel: +49 (0) 89 370012-0
Fax: +49 (0) 89 370012-12
www.InterwriteLearning.com
Support: 480.443.2214