elero Antriebstechnik 285XX0901 RC System for rolling shutters / awnings and venetian blinds User Manual Combio 915 120 V USA CA Combio 915 USA 11 05

elero GmbH Antriebstechnik RC System for rolling shutters / awnings and venetian blinds Combio 915 120 V USA CA Combio 915 USA 11 05

Contents

User Manual

Combio-915/120 VCombio-915 JA 285000906 Combio-915 RM 285200906 181106606/0510 EN/ES/PTBedienungsanleitungBitte bewahren Sie die Bedienungsanleitung auf!Operating InstructionsPlease keep the instructions in a safe place.Instrucciones de servicio¡Por favor, conserve estas instrucciones de servicio!Instruções de serviçoPor favor conserve as instruções em lugar seguro.eleroPTPTelero GmbHAntriebstechnikLinsenhofer Str. 59–63D-72660 BeurenTel.: +49 (0) 7025-13-01Fax: +49 (0) 7025-13-212www.elero.cominfo@elero.de
ContentsUSA/CA-1Safety tipsUSA/CA-2USACASafety tips .......................................... USA/CA- 2General ............................................. USA/CA- 3Use in accordance with the regulations ........... USA/CA- 3Optimal use of the radio signal ................. USA/CA- 4Mounting options ................................. USA/CA- 5Combio-915 JA for venetian blind drives ...... USA/CA-6Combio-915 RM for tubular motors ........... USA/CA- 7Connection and installation ...................... USA/CA- 8Combio-915 JA for venetian blind drives ...... USA/CA- 8The Combio-915 RM for elero tubular motors with plug-in cable (limit switch drive) .......... USA/CA- 9Combio-915 RM for tubular motors with plug-in cable (ACS-E electronic drive)......... USA/CA-10Combio-915 RM for tubular motors with fixed cable (limit switch drive) ............ USA/CA-11Combio-915 RM for elero tubular motorswith fixed cable (CSM-E electronic drive) for textile sun protection. ...................... USA/CA-12Technical data ..................................... USA/CA-13Troubleshooting ................................... USA/CA-13EC-Declaration of conformity...................... USA/CA-14Important safety indications!Observe the following Instructions.Danger of injury due to electric shocks.Connections to the 120 V mains supply mustbe carried out by authorized, specialized personnel.• Check the installations regularly for wear andtear or damage.• The regulations stipulated by the local powersupply company should be observed duringconnection work, as well as the regulations forwet and damp areas in accordance with NFPA. • Observe country-specific regulations.• Only use unaltered elero original parts.• Ensure that nobody is within the vicinity of theinstallation until it is brought to a standstill.• When carrying out work on the installation (e.g. maintenance), always disconnect theinstallation from the mains supply.• Keep children away from controls.• The control unit must be installed so that it isnot exposed to rain.Warning!
USA/CA-3General/Use in accordance with theregulationsUSA/CA-4General informationThe Combio-915 JA/RM radio receiver allows the extension ofalternating current drives to a radio drive.Use in accordance with the regulationsThe Combio-915 JA/RM can only be used for controlling rollershutters and sun protection systems such as venetian blinds.• Please observe that radio equipment cannot be operated inareas with a high interference risk level (e.g. hospitals, airports).• The remote control is only allowed for devices and installations inwhich a malfunction in the hand-held transmitter or the receiverdoes not represent a threat to persons, animals or things or forinstallations in which this risk is excluded by other safetysystems. • The user does not have any protection from interferences fromother telecommunication and terminal equipment (e.g. includingradio equipment which is operated in accordance with the corre-sponding regulations in the same frequency range).• Connect radio receivers only to the devices and installationsauthorized by the manufacturer.Optimal use of the radio signalNote: Radio installations which transmit with the samefrequency can cause reception interferences.Please observe that the radio signal range is restrictedby the legislator and structural measures.Optimal use of the radio signal• Do not bend the antenna. • Do not shorten or extend the antenna.• If reception is poor, adjust the antenna.• Install the antenna so that it is as exposed as possible.• Antenna is not to rest on metal.• Using a number of receivers may cause interference.USACA
USA/CA-5Mounting optionsUSA/CA-6Combio-915 JACombio-915 JA for venetian blind drives (28 500.0001)The Combio-915 JA is suitable for the use with venetian blind drives.In order to carry out an exact slat tilting, the Combio-915 JA has adead-man operating mode. If the button on the hand-held trans -mitter is pressed until the LED goes out, the receiver activates theself-locking operating mode.The handheld transmitter can be used to save an intermediateposition and tilting position for the slats (Drefer to the transmitterinstructions).Mounting optionsCombio-915 JA1. Put the Combio-915 into the mountingclamp.2. Fasten the Combio-915JA + clamp to the insideor outside of the channel.Mounting optionsCombio-915 RM1. Stick the enclosed adhesive strip onto theCombio-915 RM.Combio with clipCombio withclip innerCombio withclip outerCombio with clipJACombio-915PELNDrive321AntennaMains230 V/50 HzNote: Do not shorten or lengthen the antenna.USACA
USA/CA-7Combio-915 RMUSA/CA-8Combio-915 RM for tubular motors (28 520.0001)The Combio-915 is suitable for the use with tubular motors forroller shutters and sun protection systems.If a command is sent, the receiver immediately activates the self-locking operating mode. The hand-held transmitter can be used to program an intermediateposition.For sun protection systems it is possible to additionally program afabric tautening and a ventilation position for roller shutters (Drefer to the transmitter instructions).RMCombio-915PELNDriveAntennaMains230 V/50 HzNote: Do not shorten or lengthen the antenna.Pin Wire colourdesignationL BrownN BluePE Green/yellowConnection and installation (Combio-915 JA)Combio-915 JA for venetian blind drives1. Put the drive into operation with the installation cable andset the upper and lower limit switch.2. Move the hangings with the installation cable to anintermediate position.3. Switch off the mains voltage.4. Unplug the installation cable.5. Connect the female Hirschmann-plug of the radio receiverwith the drive plug.6. Connect the Hirschmann-plug of the radio receiver with thefemale plug of the mains cable.Combio-915PELN1~MJA123123AntennaMains230 V/50 Hz7. Fasten the radio receiver.8. Switch the mains voltage on again.9. Programme the transmitter (Drefer to the transmitter instructions).USACA
USA/CA-9Connection and installation (Combio-915 RM)USA/CA-10The Combio-915 RM for elero tubular motors with plug-incable (limit switch drive)1. Switch off the mains voltage.2. Press the locking mechanism of the drive plug towards thecable with a screwdriver.3. Pull out the plug.4. Plug the motor cable of the radio receiver into the drive.5. Connect the mains cable of the Combio-915 RM correctly withthe mains voltage.RMCombio-915PELNAntenna1~MMains230 V/50 Hz6. Fasten the radio receiver.7. Switch the mains voltage on again.8. Programme the transmitter (Drefer to the transmitterinstructions).9. Mount the hangings and set the limit switch.Pin Wire colourdesignationL BrownN BluePE Green/yellowConnection and installation (Combio-915Combio-915 RM for tubular motors with plug-in cable (ACS-E electronic drive)1. Switch off the mains voltage.2. Press the locking mechanism of the drive plug towards thecable with a screwdriver.3. Pull out the plug.4. Plug the motor cable of the radio receiver into the drive.5. Connect the mains cable of the Combio-915 RM correctly withthe mains voltage.RMCombio-915PELNAntenna1~MMains230 V/50 Hz6. Fasten the radio receiver.7. Switch the mains voltage on again.8. Programme the transmitter (Drefer to the transmitterinstructions).Note: Rotate the winding shaft manually in the correspondingdirection.9. Mount the hangings and operate the drive in the self-program-ming mode.Pin Wire colourdesignationL BrownN BluePE Green/yellowUSACA
USA/CA-11Connection and installation (Combio-915 RM)USA/CA-12Combio-915 RM for tubular motors with fixed cable (limit switch drive)1. Switch off the mains voltage.2. Cut off the plug of the radio receiver.3. Prepare the cable for connection (remove cable jacket andstrip).4. Connect the motor cable of the drive and the cable of theCombio-915 RM correctly (connect the same colours).5. Connect the mains cable of the Combio-915 RM correctly withthe mains voltage.RMPENLCombio-9151~MAntennaPENbr.bl.Mains230 V/50 Hz6. Fasten the radio receiver.7. Switch the mains voltage on again.8. Programme the transmitter (Drefer to the transmitterinstructions).9. Mount the hangings and set the limit switch, provided that the limitswitches have not already been set using the installation cable.Pin Wire colourdesignationB/VBrownV/BBlackN BluePE Green/yellowPin Wire colourdesignationL BrownN BluePE Green/yellowConnection and installation (Combio-915 RM for CSM-E)Combio-915 RM for elero tubular motors with fixed cable (CSM-E electronic drive) for textile sun protection.Note: CSM-E drives must not be connected using the connectorlocated on the Combio-915 RM.1. Put the drive into operation with the installation cable (programme the end positions).2. Move the hangings with the installation cable to an intermediateposition.3. Switch off the mains voltage.4. Disconnect the installation cable.5. Cut off the plug of the radio receiver.6. Prepare the cable for connection (remove cable jacket and strip).7. Connect the motor cable of the drive and the cable of theCombio-915 RM correctly (connect the same colours).8. Connect the mains cable of the Combio-915 RM correctly withthe mains voltage.RMPENLCombio-9151~MAntennaPENbr.bl.Mains230 V/50 Hz10. Fasten the radio receiver.11. Switch the mains voltage on again.12. Programme the transmitter (Drefer to the transmitterinstructions).Pin Wire colourdesignationB/VBrownV/BBlackN BluePE Green/yellowPin Wire colourdesignationL BrownN BluePE Green/yellowUSACA
USA/CA-13Technical data/TroubleshootingUSA/CA-14TroubleshootingProblem Cause Solution No radio 1. Transmitter is 1. Program thereception not programmed. transmitter.2. No mains 2. Switch on the mainsvoltage. supply again.Bad radio Unsuitable receiver Change the location ofreception position. the receiver or the antenna.Inverted sense Sense are program- Delete transmitter andof rotation med incorrectly. program correctly.Combio-915 JA Combio-915 RM(venetian blind drives) (tubular motors)Nominal voltage 120 V 120 VFrequency 60 Hz 60 HzMax. 450 W 450 WProtection class IP 54 IP 54Permitted ambienttemperature –20 to +80°C –20 to +80°CRadio frequency 915 MHz frequency bandMains cable 0,5 m with 3 mHirschmann plugMotor cable 0,25 m with 0,25 m withHirschmann female plug plugDimensions in mm L 100 x B 44 x H 15 L 100 x B 44xH15Max. numberof transmitters 16 16USACATechnical dataEC-Declaration of conformityE C - D E C L A R A T I O N O F C O N F O R M I T YWe hereby declare that the following mentioned product/s meet/sthe standards of the European Community.Product designation: ProLinexCombio-868/ -915/ -433 all versionsxVarioTec-868 /-915 all versionsxRevio-868 all versionsxAeroControl-868xUniLogic-868/ -915Description: Radio receiver for controlling roller shutters,blinds and other shading systems The conformity of the above mentioned products with the relevantrequirements is approved by the following directives and standards:xEMC Directive 2004/108/ECxEN 60335-1, EN 61000-6-2, EN 61000-6-3, EN 61000-4-5xLow Voltage Directive 2006/95/ECxEN 61000-4-4, EN 61000-4-2xEN 61000-4-11, EN 61000-4-5xR&TTE-Directives 1999/5/ECxETSI EN 301 489-3 V1.4.1xETSI EN 300 220-3 V2.3.1 xDIN EN 60730-1 (VDE 0631 part 1); EN 30730-1 +A1 +A2 +A11 bis A17 xDIN EN 60730-2-7 (VDE 0631 part 2-7);EN 60730-2-7 +A1 +A11 +A12 +A13 +A14Beuren, 29.12.2009elero GmbHUlrich Seeker Antriebstechnik– CE Officer – Linsenhofer Str. 59–63– Representative – D-72660 Beuren

Navigation menu