iLuv Creative Technology AUDCLICK Wi-Fi&Bluetooth; Speaker User Manual Audclick QSG 072516

iLuv Creative Technology Wi-Fi&Bluetooth; Speaker Audclick QSG 072516

User Manual

Bottom buttonTop buttonLED indicatorVolume controlTHE AUD CLICK IS DESIGNED FOR HOME USE WI-FI CONNECTIVITY AND WILL NOT FUNCTION PROPERLY WITHIN AN OFFICE ENVIRONMENT WHERE WI-FI PROTECTIVE FIREWALLS ARE OPERATING.Quick Start GuideBottom buttonTop buttonLED indicatorVolume control12Press the top button to play/pause musicTurn clockwise toraise volume. Turn counter clockwise to lower volume.1. If battery is low, the LED indicator will ash red.Voice promptwill tell you that battery is low andit is time to charge the Aud Click.2. Using the included USB charging cable,connect one side to your PC or smartphone's USB port(DC 5V, 1A output) and the other side to the Aud Click.3. While charging, LED indicator will remain red until fullycharged. Once fully charged, LED will turn o.Noted : We recommend you keep charging the unit if you set alarms to prevent battery low and missed alarm.WHAT’S INCLUDED CONTROLSAud Click Main UnitSETTING UPWIFI OPERATION BLUETOOTH PAIRING (MANUALLY)BATTERY CHARGING RESET THE UNITPOWERING UP1. Power on the unit. Unit should be under WiFi mode and white LED will stay on.2. Press and hold the top ring for 2 seconds, until you can hear prompting tone and white LED is ashing. Then, you cancommand Aud Click to operate by pressing top button and using voice command.Below is some example:• Play Music - Click and Say “Play music on iTunes Radio”• Weather - Click and Say "What's the weather in New York?"• Spelling - Click and Say "How do you spell Apple?"1. Download the Aud Click APP to your smartphone (available in the appleor android app stores)2. Follow the procedure on the app to setup Aud Click3. On the app, go to Amazon and input your Amazon account info to set up Alexa.After set up, Aud Click can run by itself without APP.White LEDWiFi is connectedFlashing white LEDWiFi is not connectedFlasinhg Red IndicatorTime to charge Voice Prompt“Battery is low”USB charging cableDC 5V, 1A outputWhite LEDFully charged1. Power on the unit, and double click the top ring. LED indicator will change to blue indicating that the Aud Click is in Bluetooth mode.2. Press the WPS button, located at the bottom of the unit once. Aud Click will go into Bluetooth pairing mode and LED indicator will ash blue.3. On your smartphone or tablet turn on Bluetooth and then select "iLuv AudClick". Once Bluetooth is connected,Blue LED will stop ashing and stay on.4. Press the top ring to play/pause music.Turn the silver ring clockwise to raise the volume, and counter-clockwise to lower the volume.5. Double click the top ring to switch back to WiFi mode.1. If the unit behaves abnormally, just use a paper clip or similar shaped tool to press the reset button which is located at the bottom of the unit.2. After reset is done, you need to set it up itfrom the beginning again.RESETTo power on, press and hold the WPS (WiFi protected setup) button, located at the bottom of the unit for 2 seconds. Once on, wait a few seconds for unit to start up and Aud Click will default into WiFi mode. LED will ash white until connected. Once WiFi is success-fully set up, LED will not ash but will light up white. Remark: USB only charging function
THE DISPOSAL OF ELECTRICAL AND ELECTRONIC EQUIPMENT WASTE PRODUCTS ON THE PART OF FINAL USERS IN THE EUROPEAN UNION This symbol on the product or on the container indicates that this product cannot be eliminated with the general waste.The user is responsible for eliminating this kind of waste by throwing them away at a “recycling point” specifically for electrical and electronic waste.Selective collection and electrical equipment recycling contribute to preserve natural resources and warrant waste recycling to protect environment and health.In order to receive further information about electrical and electronic waste collecting and recyling,contact your Local Council,the service of household waste or the establishment where the product was acquired.
FCC Statement:This device complies with part 15 of the FCC Rules. Operation is subject to the followingtwo conditions: (1) This device may not cause harmful interference, and (2) this devicemust accept any interference received, including interference that may cause undesiredoperation.This equipment has been tested and found to comply with the limits for a Class B digitaldevice, pursuant to part 15 of the FCC Rules. These limits are designed to providereasonable protection against harmful interference in a residential installation. Thisequipment generates, uses and can radiate radio frequency energy and, if not installedand used in accordance with the instructions, may cause harmful interference to radiocommunications. However, there is no guarantee that interference will not occur in aparticular installation. If this equipment does cause harmful interference to radio ortelevision reception, which can be determined by turning the equipment off and on, theuser is encouraged to try to correct the interference by one or more of the followingmeasures:—Reorient or relocate the receiving antenna.—Increase the separation between the equipment and receiver.—Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected.—Consult the dealer or an experienced radio/TV technician for help.Caution: Any changes or modifications not expressly approved by the party responsiblefor compliance could void the user's authority to operate the equipment.This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.This transmitter must not be co-located or operating in conjunction with any other antenna ortransmitter.
Use the This product in the environment with the temperature between -10oC and 50oC.For the following equipment: Is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC, The equipment was passed. The test was performed according to the following European standards: ETSI EN 300 328 v1.9.1 (2015-02); ETSI EN 301 489-1 V1.9.2: 2011-09; ETSI EN 301 489-17 V2.2.1: 2012-09; EN 62479:2010

Navigation menu