ADC Telecommunications PSM0804A FlexWave™ Prism - Cellular 40 Watt User Manual 2

ADC Telecommunications Inc FlexWave™ Prism - Cellular 40 Watt Users Manual 2

Users Manual 2

Download: ADC Telecommunications PSM0804A FlexWave™ Prism - Cellular 40 Watt User Manual 2
Mirror Download [FCC.gov]ADC Telecommunications PSM0804A FlexWave™ Prism - Cellular 40 Watt User Manual 2
Document ID1600135
Application IDRRGwgvwfKhmVpQ/cs8rP0w==
Document DescriptionUsers Manual 2
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize200.42kB (2505223 bits)
Date Submitted2011-12-11 00:00:00
Date Available2011-12-11 00:00:00
Creation Date2017-11-02 21:57:39
Producing SoftwareGPL Ghostscript 9.18
Document Lastmod2017-11-02 21:57:39
Document TitleADC FlexWave Prism Element Management System 7.1 User Manual
Document CreatorFrameMaker 7.1
Document Author: TE106558

Using t he Prism EMS
Viewing Alarm Details
I n m any inst ances, a page will have an Alarm Status colum n, which indicat es
whet her an alarm is act ive. I f an alarm is act ive, t here will be a Minor or Major link
( as shown in Figure 19) t hat you click t o open a dialog t hat defines t he act ive
alarm . The background color of t he Alarm Status cell also indicat es t he alarm level.
Figure 19. Alarm Link
For inform at ion on t he Alarm indicat or in t he Syst em Tree, see “ Syst em Tree” on
page 41.
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
Page 45
© 2011 ADC Telecom m unicat ions, I nc.
How t o Use t he EMS Graphical User I nt erface
Sorting Tables
You can change t he order of a t able’s cont ent s by applying an alphanum eric sort
on a colum n ( see Figure 20) . To t oggle a colum n by ascending or descending
order, click in t he colum n heading.
Figure 20. Sorting Tables in the GUI
Page 46
© 2011 ADC Telecommunications, Inc
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
Using t he Prism EMS
F OLLOWING THE P ROCEDURES IN THIS D OCUMENT
This sect ion t ells you how t o use t his docum ent t o use t he FlexWave Prism EMS t o
configure and m anage Prism devices.
Starting a Procedure
All procedures in t his docum ent assum e t hat you have already logged in t o t he
EMS as described in “ Access t he EMS” on page 57.
Modifying Parameters
I n general, t he procedures in t his docum ent end by having you click OK or Apply t o
accept changes or input .
When an operat ion com plet es, an Operation completed m essage displays, such as t he
one shown in Figure 21. I f an error m essage displays, follow t he screen prom pt s.
You can click Refresh t o updat e t he dat a being shown.
Figure 21. Operation Completed Message
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
Page 47
© 2011 ADC Telecom m unicat ions, I nc.
Following t he Procedures in t his Docum ent
Selecting Menu Items
I n t he Prism user docum ent at ion, when a procedure requires t hat you select a
sequence of m enu it em s, a right - angle sym bol separat e t he it em s. For exam ple,
in t he following graphic, “ click Users > Manage Users” indicat es t hat in t he Syst em
Menu bar you select Users, and t hen in t he Users list , select Manage Users.
Page 48
© 2011 ADC Telecommunications, Inc
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
Using t he Prism EMS
U SING THE H ELP E MBEDDED IN THE GUI
The following sect ions t ell you how t op access and use t he em bedded Prism Help
m odule.
Accessing Help
I n t he Orient at ion Links, click Help > Contents.
Prism Help is cont ext sensit ive, which m eans t hat t he Help t opic t hat opens will
pert ain t o t he current view in t he EMS View Fram e. I n t he following exam ple,
t he Help Topic for t he Get Information page has opened.
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
Page 49
© 2011 ADC Telecom m unicat ions, I nc.
Using t he Help Em bedded in t he GUI
Navigating Help
The Help Module is designed like a book t o m ake it easy t o navigat e.
Using the Contents Tab
The default view opens wit h t he Contents navigat ion t ool open. I n t he following
exam ple, you can see where t he Get Information t opic falls wit hin t he order of
cont ent s.
•
Click on any of t he Contents links t o go t o t he specified t opic.
•
Click on t he book icons t o open/ close t he chapt ers.
Page 50
© 2011 ADC Telecommunications, Inc
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
Using t he Prism EMS
You can also use t he Show in Contents but t on t o show where a t opic falls wit hin t he
book hierarchy:
Using the Orientation Links and Buttons
You can use t he int eract ive orient at ion links in t he t opic header. These links show
where t he t opic falls wit hin a chapt er. Click on t he links in t he t opic header t o m ove
back one st ep in t he book hierarchy.
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
Page 51
© 2011 ADC Telecom m unicat ions, I nc.
Using t he Help Em bedded in t he GUI
You can also use t he Page Up but t on, Page Down but t on, Print but t on, and
Bookm ark but t on t o bookm ark a t opic.
Using the Index Tab
Click Index t o open t he Index panel.
At t he t op of t he Index panel is t he alpha- num eric orient at ion t ool. I n t his exam ple,
t he let t er D is select ed, which result s in only t hose indexed words t hat st art wit h
Page 52
© 2011 ADC Telecommunications, Inc
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
Using t he Prism EMS
“ D” t o display, in alphabet ic order. Click on any of t he links t o go t o t he t opic t hat
has t he indexed t erm in it .
To m ove up/ down or left / right t o change t he orient at ion of t he t ext in t he I ndex
panel, use t he navigat ion arrows.
Using the Search Tab
Click Search t o open t he Search panel.
At t he t op of t he Search panel is a t ext box in which you ent er t he t erm for which
you want t o search. I n t his exam ple t he user is searching for t he word
“ passband.”
To act ivat e t he search, click t he Go but t on.
The Search panel is populat ed wit h links t o t he t opics t hat cont ain t he word
“ passband” and are ordered from t op down in order of probabilit y of which t opic
will cont ain t he t opic for which you are searching.
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
Page 53
© 2011 ADC Telecom m unicat ions, I nc.
Using t he Help Em bedded in t he GUI
I nt ent ionally Blank Page
Page 54
© 2011 ADC Telecommunications, Inc
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
INITIAL FLEXWAVE PRISM SYSTEM SETUP
Topics
Page
Minim um EMS Syst em Requirem ent s ........................................................................................ 56
Access t he EMS ..................................................................................................................... 57
Set Session Tim eout ............................................................................................................... 59
Set Dat e and Tim e ................................................................................................................. 60
Set Net work Connect ions ........................................................................................................63
Configure Basic Host Unit Propert ies ......................................................................................... 64
Label t he PRU/ URU................................................................................................................. 66
Label t he Host Opt ical Port s..................................................................................................... 67
Label PRU/ URU Opt ical Port s ................................................................................................... 70
Configure DART Links ............................................................................................................. 71
Classic DART Models ......................................................................................................... 75
800 APAC iDEN Classic DART ........................................................................................ 75
800 SMR Classic DART ................................................................................................. 75
900 SMR Classic ......................................................................................................... 76
2100 AWS Classic DART............................................................................................... 76
Cellular Classic DART................................................................................................... 77
PCS Classic DART........................................................................................................ 77
SuperDART Models ........................................................................................................... 79
700 Lower ABC SuperDART .......................................................................................... 79
700 UpperC SuperDART ............................................................................................... 79
2100 AWS SuperDART ................................................................................................. 79
EGSM 900 SuperDART ................................................................................................. 79
GSM 1800 SuperDART ................................................................................................. 80
PCS SuperDART .......................................................................................................... 80
UMTS SuperDART ....................................................................................................... 80
DART St art and St op Frequencies ....................................................................................... 81
Set t he Forward and Reverse Delays......................................................................................... 82
Using t he Linked DARTs Delay Table ................................................................................... 83
Filt ering t he Linked DARTs Delay Table ................................................................................ 84
Configure Host Forward Gain ................................................................................................... 85
Configure Host Reverse Gain ................................................................................................... 88
Configure Rem ot e Forward Gain ............................................................................................... 91
Configure Reverse I nput Power Levels ...................................................................................... 94
The st eps provided in t his chapt er configure a basic Prism syst em t hat includes:
•
one Host Unit ( Host )
•
at least one Prism Rem ot e Unit ( PRU) .
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
Page 55
© 2011 ADC Telecommunications, Inc.
Minim um EMS Syst em Requirem ent s
MINIMUM EMS SYSTEM REQUIREMENTS
The com put er t hat you use t o rem ot ely access t he EMS m ust m eet t he following
m inim um requirem ent s:
•
Windows 2000 or Windows XP operat ing syst em
•
I nt ernet Explorer version 7.x or FireFox 3.6
•
Net work I nt erface Card ( NI C)
•
Et hernet cable wit h RJ- 45 connect ors.
The EMS dat abase can also be accessed rem ot ely using an SNMP m anager. I n t his
case, t he user int erface varies depending on t he SNMP m anager, but t he
underlying param et ers, param et er values, and alarm s are t he sam e as in t he
st andard EMS int erface.
Page 56
© 2011 ADC Telecommunications, Inc
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
I nit ial FlexWave Prism Syst em Set up
ACCESS THE EMS
NOTE:
In the default configuration, the Craft port has a DHCP server that assigns an IP address
to the computer that is connected. You should therefore have your network interface
configured for DHCP, or configured with a static IP address in the same subnet, where the
default is 192.168.0.1/24.
To allow t he EMS popup and alarm
screens t o funct ion correct ly, do one
of t he following:
•
•
Disable t he popup blocker for
your web browser.
Ent er t he syst em I P address in
t he web browser’s t rust ed sit es
list .
Use an Et hernet CAT 5 cable
( st raight or crossover) wit h RJ- 45
connect ors t o connect a lapt op t o
t he Craft port of t he Host .
Connect your com put er and st art a
web browser.
I n t he web browser URL box, ent er
t he
following
IP
address:
192.168.0.1
RJ-45
Connector
Detail
77073-075
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
Page 57
© 2011 ADC Telecom m unicat ions, I nc.
Access t he EMS
When t he Welcome to ADC FlexWave Prism & URH and ADC InterReach Spectrum window
opens:
I n t he User Name box, t ype t he user nam e provided by ADC or by t he Net work
Adm inist rat or. The default user nam e is admin.
I n t he Password box, t ype t he password provided by ADC or by t he Net work
Adm inist rat or. The default password is adc123.
Once inst allat ion is com plet e, users can be added and passwords can be
changed. For furt her inform at ion, see “ Users” on page 203.
Click Log in t o open t he default page, which com prises t he elem ent s list ed
below.
•
The Syst em Tree will be populat ed wit h inst alled devices, but no device will
be select ed.
•
I n t he EMS View Fram e, t he default page displays when t he Host is select ed
in t he Syst em Tree.
Page 58
© 2011 ADC Telecommunications, Inc
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
I nit ial FlexWave Prism Syst em Set up
SET SESSION TIMEOUT
NOTE:
This feature is accessible only by a user logged in to the EMS as the admin user.
To access t he Set Session Timeout page, in t he Syst em Menu bar, click Special
Features > Set Session Timeout.
I n t he Session Idle Time box, ent er in m inut es how long t he EMS session can be
idle before a forced log out occurs; t he value m ust be bet ween 10 and 60
m inut es. The default is 30 m inut es.
Click Apply. Once t he syst em execut es t he com m and,
m essage displays.
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
an Operation completed
Page 59
© 2011 ADC Telecom m unicat ions, I nc.
Set Dat e and Tim e
SET DATE AND TIME
The following rules apply t o t he syst em t im e and dat e:
•
The support ed dat e and t im e range is from 1 January 2005 00: 00: 00 
( 12 AM) t o 31 Decem ber 2037 23: 59: 59 ( 11: 59: 59 PM) , where January is 1
and Decem ber is 12.
•
Tim e zone and day light savings are not support ed.
•
All PRUs synchronize t im e wit h t he m anaging Host at t he t im e t he connect ed
PRU is discovered. The dat e and t im e on t he PRUs t hen synchronize t o t he Host
and do not drift .
•
I f t he syst em dat e or t im e is changed while a PRU is out of com m unicat ion wit h
t he Host ( for exam ple, loss of power or scheduled m aint enance) , once
com m unicat ion is reest ablished it will t ake up t o 10 m inut es for t he PRU t o
display t he updat ed dat e or t im e.
•
I f t he difference bet ween t he set t im e and t he present t im e is great er t han t he
session t im e out set t ing, t he user will be logged out . For exam ple, if t he Session
Idle Time is set t o 10 m inut es, and t he t im e set in t his procedure is 11: 10 AM
but it is act ually 11: 30 AM, t here is a 20 m inut e difference, which t riggers t he
Session Idle Time and t he user will be logged out .
NOTE:
It can take up to 17 minutes before the updated time or date to take effect in connected
Remote Units.
NOTE:
You can set the date and time at any time independent from one another. For example, to
change the time for daylight savings, open the System Date and Time page, click on the
hour shown in the System Time box, increase or decrease the hour by one, and then click
Apply.
Page 60
© 2011 ADC Telecommunications, Inc
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
I nit ial FlexWave Prism Syst em Set up
D o t he follow in g t o se t t h e da t e a n d t im e :
To access t he Set Date and Time page, in t he Syst em Menu bar, click System
Configuration > Set Date and Time.
To change t he dat e, click t he … icon aft er t he Date (YYYY/MM/DD) box.
I n t he Calendar t hat opens, do t he following:
I n t he Mont h list , select t he m ont h.
I f necessary, use t he right arrow t o adj ust t he year higher.
I n t he calendar, select t he dat e.
Click Close.
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
Page 61
© 2011 ADC Telecom m unicat ions, I nc.
Set Dat e and Tim e
I n t he Time (HH:MM:SS) box, ent er t he syst em t im e in t he 24- hour clock
HH: MM: SS form at ( for exam ple, t o set t he syst em t im e t o 5: 19: 56 PM, you
would ent er 17:19:56) .
I n t he Set Date and Time page, verify t he dat e and t im e showing in t he System Date
and System Time fields.
Click Apply. Once t he syst em execut es t he com m and,
m essage displays.
Page 62
© 2011 ADC Telecommunications, Inc
an Operation completed
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
I nit ial FlexWave Prism Syst em Set up
SET NETWORK CONNECTIONS
To access t he Set Network Connections page, in t he Syst em Menu bar, click System
Configuration > Set Network Connections.
Use t he Networking Mode list t o specify t he m ode under which I P addresses are
assigned t o t he Host Craft and Net work port s. A single I P address defines t he
syst em . This I P address is assigned t o t he Host eit her st at ically or by t he DHCP
server on t he NOC. No user set t ing/ I P configurat ion is required for t he
PRUs—I P addresses for connect ed PRUs are aut o assigned.
•
DHCP—t his m ode indicat es t hat t he Host is a DHCP client and expect s an I P
address t o be assigned by an ext ernal DHCP server t hrough a net work
Et hernet connect or. The Host Craft port has a DHCP server t hat can be used
t o com m unicat e wit h t he Host direct ly, and from which you can access t he
EMS.
•
Static—t he default m ode for t he Craft Port, wit h a default I P address of
192.168.0.1. The Static Networking Mode allows you t o set an I P address for
t he Host and connect ed Rem ot e Unit s t hat do not change unless you
m anually change t hem .
I f you change a port t o Static Networking Mode, t he address fields are enabled.
Ot herwise you cannot change t he net work addresses. I f you set a port t o Static
Networking Mode, t hen do t he following:
I n t he IP Address box, ent er a new I P address for t he syst em , in t he form at
of xxx.xxx.xxx.xxx.
I n t he Subnet Mask box, ent er a new Subnet Mask address for t he syst em , in
t he form at of xxx.xxx.xxx.xxx.
I n t he Gateway box, ent er a new Gat eway address for t he syst em , in t he
form at of xxx.xxx.xxx.xxx.
Click Apply. Once t he syst em execut es t he com m and,
m essage displays.
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
an Operation completed
Page 63
© 2011 ADC Telecom m unicat ions, I nc.
Configure Basic Host Unit Propert ies
CONFIGURE BASIC HOST UNIT PROPERTIES
I n t he Syst em Tree, click on t he Host icon.
I n t he Unit Menu bar, click Unit Configuration > Edit Properties, t o open t he Unit
Configuration > Edit Properties page.
I n t he Name box, ent er an ident ifying nam e for t he Host . The Name m ust st art
wit h an alphabet ical charact er, cont ain bet ween 5 and 40 charact ers
( alphanum eric or underscore only) , and cont ain no spaces.
( Opt ional) The SeRF board on each Host and Rem ot e cont ains t he clock for t hat
unit . At t he Rem ot e, t he reference is a clock derived from t he Host clock. The
10 MHz Reference Clock default is Internal. You can change t he 10 MHz Reference Clock
set t ing t o External, which allows you t o frequency lock t he clock t o an ext ernal
10 MHz reference.
CAUTION!
When using the 10 MHz external reference clock, the signal must be connected to the Host
before enabling the clock in the software. If an external 10MHz reference clock is selected
for operation, but is not present or outside of the frequency range of 10MHz +/- 5ppm,
communication between the Host and Remote over the optical fiber will fail.
I n t he System Card Output Clock list , select one of t he following:
•
10 MHz t o set t he Host as t he Syst em Card Out put Clock.
•
Off t o disable t he Syst em Card Out put Clock. Unless your syst em requires
t he 10 MHz out put , it is best t o leave t he System Card Output Clock disabled, as
t his set t ing saves power and lowers em issions.
•
30.72 MHz is not applicable t o a Prism syst em and should not be select ed.
Page 64
© 2011 ADC Telecommunications, Inc
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
I nit ial FlexWave Prism Syst em Set up
( Opt ional) Use t he Notes box t o ent er not es specific t o t his Host . You can ent er
up t o 256 charact ers; all keyboard charact ers can be used.
Click Apply. Once t he syst em execut es t he com m and,
m essage displays.
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
an Operation completed
Page 65
© 2011 ADC Telecom m unicat ions, I nc.
Label t he PRU/ URU
LABEL THE PRU/URU
I n t he Syst em Tree, click t he icon of t he PRU/ URU whose propert ies you want
t o change.
I n t he Unit Menu bar, click Unit Configuration > Edit Properties, t o open t he Unit
Configuration > Edit Properties page for t he select ed PRU/ URU.
I n t he Name box, ent er an ident ifying nam e for t he PRU/ URU. The Name m ust
st art wit h an alphabet ical charact er, cont ain bet ween 5 and 40 charact ers
( alphanum eric or underscore only) , and cont ain no spaces.
Leave t he Capacity set t ing as is.
CAUTION!
The Capacity setting pertains to the PRU/URU Remote SeRF Interface (RSI) board and the
number of RF groups available to the Remote Unit. This parameter is set during
manufacturing and should be changed only when the RSI board has been replaced. See
“Set the Capacity for a New Remote Unit RSI Board” on page 162.
( Opt ional) Use t he Notes box t o ent er not es specific t o t he select ed PRU/ URU.
You can ent er up t o 256 charact ers; all keyboard charact ers can be used.
Click Apply. Once t he syst em execut es t he com m and,
m essage displays.
Repeat t his process for each PRU/ URU in t he syst em .
Page 66
© 2011 ADC Telecommunications, Inc
an Operation completed
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
I nit ial FlexWave Prism Syst em Set up
LABEL THE HOST OPTICAL PORTS
CAUTION!
If fibers must be moved or reconfigured at any time during installation or setup, follow
the steps in “Moving or Reconfiguring Fibers” on page 122.
There can be up t o eight Host SeRF opt ical port s t hat correspond t o t he eight
physical port s on t he Host . I n t his sect ion, you should label t he Host SeRF Opt ical
port s t o provide for easier off- sit e m anagem ent .
77152-009
I n t he Syst em Tree, click on a Host icon.
I n t he Unit Menu bar, click Unit Configuration > Configure Optical Ports, t o open t he
Unit Configuration > Configure Optical Ports page.
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
Page 67
© 2011 ADC Telecom m unicat ions, I nc.
Label t he Host Opt ical Port s
I n t he SFP Name box, ent er a label for t he select ed Opt ics port . The SFP Name
m ust st art wit h an alphabet ical charact er, cont ain 5 t o 32 charact ers
( alphanum eric or underscore only) , and cont ain no spaces. The default SFP
Name is UNKNOWN_SFPNAME.
Click Apply. Once t he syst em execut es t he com m and,
m essage displays.
an Operation completed
The Configure Optical Ports t able provides t he following inform at ion.
•
SFP Number—syst em assigned num ber ( from 1 t o 8) for t he Opt ical port s
•
SFP Name—see St ep 3 on page 68.
•
In/Out—used for cascading, which is not support ed in t his release. The Host will
t herefore always be set as Out ( indicat es t hat t he forward link for t he connect ed
SFP is going away from t he Host ) and t he SFPs for all Rem ot e Unit s will always
be set as In.
•
Optics Type
– LongRange—26 dB
– IntermediateRange—18 dB)
•
Wavelength (nm)—num ber displayed is t he wavelengt h t ransm it t ed t hrough t his
port :
– Non- duplex and WDM configurat ions

1550 nm fwd

1310 nm rev
– CWDM configurat ions can be one of eight wavelengt hs:

1470 nm

1550 nm

1490 nm

1570 nm

1510 nm

1590 nm

1530 nm

1610 nm
Page 68
© 2011 ADC Telecommunications, Inc
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
I nit ial FlexWave Prism Syst em Set up
•
Tx Power (dBm)—launch power level in dBm of forward pat h signal.
– LongRange ( LR)

m inim um is - 2 dBm

m axim um is 3 dBm .
– I nt erm ediat eRange ( I R)

m inim um is - 5 dBm

m axim um is 0 dBm .
•
Rx Power (dBm)—receive power level in dBm of reverse pat h signal, which
incorporat es t he launch power of t he Rem ot e Unit SFP plus all opt ical losses
( insert ion losses, fiber cable loss, and so fort h) .
– LongRange ( LR)

m inim um is - 27 dBm

m axim um is - 9 dBm .
– I nt erm ediat eRange ( I R)

m inim um is - 18 dBm

m axim um is 0 dBm .
•
Remote Name or Host Name—when a Host Unit is select ed in t he Syst em Tree, t he
Configure Optical Ports t able provides a colum n for Remote Name, which is nam e of
t he Rem ot e Unit connect ed t o t his Opt ics port . When a Rem ot e Unit is select ed
in t he Syst em Tree, t he Configure Optical Ports t able provides a colum n for t he Host
Name, which is t he nam e of t he Host connect ed t o t his Opt ics port .
•
Alarm Status—whet her an alarm is act ive. I f an alarm is act ive, t here will be a
Minor or Major link t hat you click t o open a dialog t hat defines t he act ive alarm ,
as described in “ Viewing Alarm Det ails” on page 45. The background color of
t he Alarm Status cell also indicat es t he alarm level ( see “ Alarm Color Codes” on
page 44) .
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
Page 69
© 2011 ADC Telecom m unicat ions, I nc.
Label PRU/ URU Opt ical Port s
LABEL PRU/URU OPTICAL PORTS
I n t he Syst em Tree, click on a PRU/ URU icon.
I n t he Unit Menu bar, click Unit Configuration > Configure Optical Ports, t o open t he
Unit Configuration > Configure Optical Ports page.
I n t he SFP Name box, ent er a label for t he select ed Opt ics port . The SFP Name
m ust st art wit h an alphabet ical charact er, cont ain bet ween 5 and 32 charact ers
( alphanum eric or underscore only) , and cont ain no spaces. The default SFP
Name is UNKNOWN_SFPNAME.
Click Apply. Once t he syst em execut es t he com m and,
m essage displays.
Repeat t his process for each PRU/ URU in t he syst em .
an Operation completed
The Configure Optical Ports t able provides t he sam e inform at ion as what is shown for
a Host Unit —see “ Label t he Host Opt ical Port s” on page 67.
Page 70
© 2011 ADC Telecommunications, Inc
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
I nit ial FlexWave Prism Syst em Set up
CONFIGURE DART LINKS
“ Linking” est ablishes an associat ion in soft ware bet ween a part icular Host DART
and a part icular Rem ot e DART, enabling t he t wo DARTs t o act as an operat ional
unit in providing one RF band. There are four pre- requisit es t o t his procedure:
•
The Host DART and Rem ot e DART m ust be connect ed t hrough t he opt ical fiber
and be com m unicat ing wit h each ot her.
•
To link t he Rem ot e Unit DARTs t o t he DARTs in a Host Unit , t he DARTs m ust
be t he sam e t ype e ( such as, Cellular t o Cellular) .
•
SuperDARTs and Classic DARTS do not operat e wit h each ot her. Link a
SuperDART t o a SuperDART and a Classic DART t o a Classic DART.
•
There m ust be a sufficient num ber of fiber t im eslot s available in order t o
accom m odat e t he request ed passband ( for exam ple, PCS A band requires 3
t im eslot s) .
I n t he Configure DART Links page, all Rem ot e DARTs are list ed t hat have t he sam e
band as t he select ed Host DART. A link is est ablished by select ing a Rem ot e DART
t o be paired wit h t he Host DART, and t hen clicking t he Linked box. To provide for
an RF Sim ulcast , a Single Host DART can be linked t o up t o eight Rem ot e DARTs.
Do t he following t o est ablish DART links:
To access t he Configure DART Links page, in t he Syst em Menu bar, click System
Configuration > Configure DART Links.
NOTE:
For information on the Linked DARTs table at the bottom of the Configure DART Links
page, see “Viewing the Linked DARTs Report” on page 105.
You use t he Configure Bands panel t o configure t he Host for DART linking, and t he
Remote Parameters panel t o configure t he Rem ot e Unit .
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
Page 71
© 2011 ADC Telecom m unicat ions, I nc.
Configure DART Links
I n t he Host Parameters panel, set t he following param et ers:
I n t he DART list , select t he Host DART t hat you want t o link t o t he Rem ot e
Unit DART.
I n t he DART Name box, ent er a nam e for t he DART, which m ust st art wit h an
alphabet ical charact er, cont ain bet ween 5 and 32 charact ers ( alphanum eric
or underscore only) , and cont ain no spaces.
Use t he Passband colum n t o set t he passband for t he select ed DART.
•
I f you are configuring a Classic DART, t hen refer t o t he passband
select ion t able in t he corresponding sect ion:

“ 800 APAC iDEN Classic DART” on page 75

“ 800 SMR Classic DART” on page 75

“ 900 SMR Classic” on page 76

“ 2100 AWS Classic DART” on page 76

“ Cellular Classic DART” on page 77

“ PCS Classic DART” on page 77
The following figure shows t he passband select ions for t he 2100 AWS
Classic DART, which are described in “ 2100 AWS Classic DART” on
page 76.
Page 72
© 2011 ADC Telecommunications, Inc
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
I nit ial FlexWave Prism Syst em Set up
•
I f you are configuring a SuperDART, in t he Passband colum n, click on t he
Configure link, and t hen in t he passband select ion window t hat opens,
set t he passband according t o t he rules specified for each SuperDART
t ype:

“ 700 Lower ABC SuperDART” on page 79

“ 700 UpperC SuperDART” on page 79

“ 2100 AWS SuperDART” on page 79

“ EGSM 900 SuperDART” on page 79

“ GSM 1800 SuperDART” on page 80

“ PCS SuperDART” on page 80

“ UMTS SuperDART” on page 80
The following figure shows t he passband select ions for a PCS SuperDART,
which are described in “ PCS SuperDART” on page 80.
The Frequency t able provides a read- only t abular view of forward and reverse
pat hs.
•
I n t he Diversity list , select whet her t he DART is t o be configured as Diversity
or Non Diversity. For a diversit y applicat ion, one DART will be configured
Non Diversity for t he prim ary FWD/ REV pat h signal and t he ot her DART will
be configured Diversity. This select ion t herefore det erm ines whet her t he
DART Module being configured will carry t he prim ary or secondary REV
( uplink) RF pat h.
•
For dual DART configurat ions, such as dual- pcs, sm r800/ sm r900 and
dual- aws, bot h DARTs m ust have DART Diversity Status set t o Non Diversity.
•
I n t he Input Source list , select whet her t he Wireless Operat or input will be
from t he BDA or BTS. Input Source det erm ines whet her Syst em Test uses
ext ernal RF ( BTS) or int ernal RF ( BDA) t o t est t he forward pat h. However,
t his release does not support int ernal t one generat ion. Consequent ly,
set t ing t he Input Source as eit her BDA or BTS assum es an ext ernal RF signal.
Default is BTS.
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
Page 73
© 2011 ADC Telecom m unicat ions, I nc.
Configure DART Links
I n t he Remote Parameters t able, set t he following param et ers:
I n t he Remote Id list , select t he Rem ot e Unit whose DART you are linking t o
t he Host DART.
I n t he DART list , select t he Rem ot e Unit DART t hat you are linking.
I n t he DART Name box, ent er a nam e for t he DART, which m ust st art wit h an
alphabet ical charact er, cont ain bet ween 5 and 32 charact ers ( alphanum eric
or underscore only) , and cont ain no spaces.
Select t he Linked box.
Click Apply. The Linked DARTS t able at t he bot t om of t he page updat es wit h t he
new link.
Repeat St ep t hrough St ep 4 for each Host and PRU/ URU DART pairing.
NOTE:
Each link takes approximately 1 minute to establish.
Page 74
© 2011 ADC Telecommunications, Inc
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
I nit ial FlexWave Prism Syst em Set up
Classic DART Models
The following sect ions describe t he Prism Classic DART opt ions.
800 APAC iDEN Classic DART
Table 13 list s t he passband select ions for 800 APAC iDEN Classic DARTs.
Table 13.
800 APAC iDEN Classic DART Passband Selection
Name
Downlink Frequency Uplink Frequency
Range (MHz)
Range (MHz)
800 APAC iDEN 851 - 870
806 - 825
The 800 APAC iDEN DART also support s t he SMR Low and SMR Low Wide
passbands. The 800 APAC iDEN Classic DART can be linked t o a DART of t he sam e
t ype and t o an 800 SMR Classic DART ( as long as t he passband is eit her SMR Low
or SMR Low Wide) . Table 14 specifies support ed linking bet ween 800 SMR Classic
DARTs and 800 APAC iDEN Classic DARTs.
Table 14.
Linking 800 SMR Classic DARTs and 800 APAC iDEN Classic DARTs
Host DART PRU/URU DART Passbands
800APAC
800APAC
low, wide,
apac
800APAC
800SMR
low, wide
800SMR
800APAC
low, wide
800SMR
800smr
low, wide
800 SMR Classic DART
Table 15 list s t he passband select ions for 800 SMR Classic DARTs.
Table 15.
800 SMR Classic DART Passband Selections
Name
Downlink Frequency Uplink Frequency
Range (MHz)
Range (MHz)
SMR Low
862 - 869
817 - 824
SMR Low Wide 851 - 869
806 - 824
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
Page 75
© 2011 ADC Telecom m unicat ions, I nc.
Configure DART Links
900 SMR Classic
Table 16 list s t he passband select ions for 900 SMR Classic DARTs.
Table 16.
NOTE:
900 SMR Classic DART Passband Selections
Name
Downlink Frequency Uplink Frequency
Range (MHz)
Range (MHz)
SMR High
935 - 940
896 - 901
SMR High/Paging 935 - 941
896 - 902
When installed in a PRU, the 900 SMR Remote Classic DART supports only the SMR High
passband.
2100 AWS Classic DART
Table 17 list s t he passband select ions for 2100 AWS Classic DARTs.
Table 17.
Page 76
© 2011 ADC Telecommunications, Inc
2100 AWS Classic DART Passband Selection
Name
Downlink
Frequency
Range (MHz)
Uplink Frequency
Range (MHz)
2110 - 2120
1710 - 1720
A+B
2110 - 2130
1710 - 1730
A+B+C
2110 - 2135
1710 - 1735
A+B+C+D
2110 - 2140
1710 - 1740
A+B+C+D+E
2110 - 2145
1710 - 1745
2120 - 2130
1720 - 1730
B+C
2120 - 2135
1720 - 1735
B+C+D
2120 - 2140
1720 - 1740
B+C+D+E
2120 - 2145
1720 - 1745
B+C+D+E+F
2120 - 2155
1720 - 1755
2130 - 2135
1730 - 1735
C+D
2130 - 2140
1730 - 1740
C+D+E
2130 - 2145
1730 - 1745
C+D+E+F
2130 - 2155
1730 - 1755
2135 - 2140
1735 - 1740
D+E
2135 - 2145
1735 - 1745
D+E+F
2135 - 2155
1735 - 1755
2140 - 2145
1740 - 1745
E+F
2140 - 2155
1740 - 1755
2145 - 2155
1745 - 1755
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
I nit ial FlexWave Prism Syst em Set up
Cellular Classic DART
Table 18 list s t he passband select ions for Cellular Classic DARTs.
Table 18.
NOTE:
Cellular Classic DART Passband Selections
Name
Downlink Frequency Uplink Frequency
Range (MHz)
Range (MHz)
A'' + A
869 - 880
824 - 835
870 - 880
825 - 835
A'' + A + A’
869 - 891.5
824 - 846.5
A’
890 - 891.5
845 - 846.5
880 - 890
835 - 845
B’
891.5 - 894
846.5 - 849
B + B’
880 - 894
835 - 849
A'' + A + B + A' + B’ 869 - 894
824 - 849
A+B
825 - 845
870 - 890
The Cellular Classic Remote DART supports the same passbands as the Cellular Classic
Host DART. However, the LNA or Duplexer installed in the Remote Unit can restrain which
passbands are supported.
PCS Classic DART
Table 19 list s t he passband select ions for PCS Classic DARTs.
Table 19.
PCS Classic DART Passband Selections
Passband Downlink Frequency Uplink Frequency
Range (MHz)
Range (MHz)
Passband
Downlink Frequency Uplink Frequency
Range (MHz)
Range (MHz)
A1
1930 - 1935
1850 - 1855
E+F+C2
1965 - 1982.5
A2
1935 - 1940
1855 - 1860
C1+G + H
1982.5 - 2000
1902.5 - 1920
A3
1940 - 1945
1860 - 1865
A+D
1930 - 1950
1850 - 1870
B1
1950 - 1955
1870 - 1875
A2+A3+D+B1
1935 - 1955
1855 - 1875
B2
1955 - 1960
1875 - 1880
A3+D+B1+B2
1940 - 1960
1860 - 1880
B3
1960 - 1965
1880 - 1885
D+B
1945 - 1965
1865 - 1885
C3
1975 - 1980
1895 - 1900
B+E
1950 - 1970
1870 - 1890
C4
1980 - 1985
1900 - 1905
B2+B3+E+F
1955 - 1975
1875 - 1895
C5
1985 - 1990
1905 - 1910
B3+E+F+C3
1960 - 1980
1880 - 1900
1945 - 1950
1865 - 1870
E+F+C3+C4
1965 - 1985
1885 - 1905
1965 - 1970
1885 - 1890
F+C
1970 - 1990
1890 - 1910
1970 - 1975
1890 - 1895
C+G
1975 - 1995
1895 - 1915
1990 - 1995
1910 - 1915
C4+C5+G + H
1980 - 2000
1900 - 1920
1995 - 2000
1915 - 1920
B3+E+F+C2
1960 - 1982.5
1880 - 1902.5
1885 - 1902.5
C2
1975 - 1982.5
1895 - 1902.5
A+D+B1
1930 - 1955
1850 - 1875
C1
1982.5 - 1990
1902.5 - 1910
A2+A3+D+B1+B2
1935 - 1960
1855 - 1880
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
Page 77
© 2011 ADC Telecom m unicat ions, I nc.
Configure DART Links
Table 19.
PCS Classic DART Passband Selections
Passband Downlink Frequency Uplink Frequency
Range (MHz)
Range (MHz)
Passband
Downlink Frequency Uplink Frequency
Range (MHz)
Range (MHz)
A1+A2
1930 - 1940
1850 - 1860
A3+D+B
1940 - 1965
1860 - 1885
A2+A3
1935 - 1945
1855 - 1865
D+B+E
1945 - 1970
1865 - 1890
A3+D
1940 - 1950
1860 - 1870
B+E+F
1950 - 1975
1870 - 1895
D+B1
1945 - 1955
1865 - 1875
B2+B3+E+F+C3
1955 - 1980
1875 - 1900
B1+B2
1950 - 1960
1870 - 1880
B3+E+F+C3+C4
1960 - 1985
1880 - 1905
B2+B3
1955 - 1965
1875 - 1885
E+F+C
1965 - 1990
1885 - 1910
B3+E
1960 - 1970
1880 - 1890
F+C+G
1970 - 1995
1890 - 1915
E+F
1965 - 1975
1885 - 1895
C+G + H
1975 - 2000
1895 - 1920
F+C3
1970 - 1980
1890 - 1900
B2+B3+E+F+C2
1955 - 1982.5
1875 - 1902.5
C3+C4
1975 - 1985
1895 - 1905
A+D+B1+B2
1930 - 1960
1850 - 1880
C4+C5
1980 - 1990
1900 - 1910
A2+A3+D+B
1935 - 1965
1855 - 1885
C5+G
1985 - 1995
1905 - 1915
A3+D+B+E
1940 - 1970
1860 - 1890
G+H
1990 - 2000
1910 - 1920
D+B+E+F
1945 - 1975
1865 - 1895
F+C2
1970 - 1982.5
1890 - 1902.5
B+E+F+C3
1950 - 1980
1870 - 1900
C1+G
1982.5 - 1995
1902.5 - 1915
B2+B3+E+F+C3+C4 1955 - 1985
1875 - 1905
1930 - 1945
1850 - 1865
B3+E+F+C
1960 - 1990
1880 - 1910
A2+A3+D
1935 - 1950
1855 - 1870
E+F+C+G
1965 - 1995
1885 - 1915
A3+D+B1
1940 - 1955
1860 - 1875
F+C+G + H
1970 - 2000
1890 - 1920
D+B1+B2
1945 - 1960
1865 - 1880
A+D+B
1930 - 1965
1850 - 1885
1950 - 1965
1870 - 1885
A2+A3+D+B+E
1935 - 1970
1855 - 1890
B2+B3+E
1955 - 1970
1875 - 1890
A3+D+B+E+F
1940 - 1975
1860 - 1895
B3+E+F
1960 - 1975
1880 - 1895
D+B+E+F+C3
1945 - 1980
1865 - 1900
E+F+C3
1965 - 1980
1885 - 1900
B+E+F+C3+C4
1950 - 1985
1870 - 1905
F+C3+C4
1970 - 1985
1890 - 1905
B2+B3+E+F+C
1955 - 1990
1875 - 1910
1975 - 1990
1895 - 1910
B3+E+F+C+G
1960 - 1995
1880 - 1915
C4+C5 +G 1980 - 1995
1900 - 1915
E+F+C+G + H
1965 - 2000
1885 - 1920
C5+G + H
1905 - 1920
1985 - 2000
Page 78
© 2011 ADC Telecommunications, Inc
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
I nit ial FlexWave Prism Syst em Set up
SuperDART Models
The following sect ions describe t he Prism SuperDART opt ions.
700 Lower ABC SuperDART
The 700 Lower ABC SuperDART support s t he following subbands: A, B, C.
Table 20 list s t he passband select ions for 700 Lower ABC SuperDARTs.
700 Lower ABC SuperDART Passband Selection
Table 20.
Name Downlink Frequency Uplink Frequency
Range (MHz)
Range (MHz)
728 - 734
698 - 704
734 - 740
704 - 710
740 - 746
710 - 716
700 UpperC SuperDART
The 700 UpperC SuperDART support s t he following passband: Upper C.
Table 21 list s t he passband select ions for 700 ABC SuperDARTs.
Table 21.
700 UpperC SuperDART Passband Selection
Name
Downlink Frequency Uplink Frequency
Range (MHz)
Range (MHz)
UpperC 746 - 756
776 - 786
2100 AWS SuperDART
You can select any num ber of t he subbands based on t he lim it at ions specified
below.
•
The 2100 AWS SuperDART support s t he following passbands: A, B, C, D, E, F.
•
You can select up t o t wo non- cont iguous set s of subbands, but t here m ust be
at least a 5 MHz gap bet ween t he bands.
•
The St art and St op frequencies are in t he range of 2110MHz - 2155MHz.
EGSM 900 SuperDART
The EGSM 900 SuperDART support s t he select ion of a St art and St op frequency
for t he passband in t he range of 925MHz - 960MHz.
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
Page 79
© 2011 ADC Telecom m unicat ions, I nc.
Configure DART Links
GSM 1800 SuperDART
You can select a St art and St op frequency for t he passband in t he frequency range
of 1805 MHz - 1880 Mhz.
PCS SuperDART
PCS SuperDARTs support t he following subbands: A, B, C, D, E, F, G, H, A1, A2,
A3, B1, B2, B3, C1, C2, C3, C4, C5.
You can select any num ber of t he subbands based on t he lim it at ions specified
below:
•
The subband A cannot be chosen in conj unct ion wit h A1, A2, or A3.
•
The subband B cannot be chosen in conj unct ion wit h B1, B2, or B3.
•
The subband C cannot be chosen in conj unct ion wit h C1, C2, C3, C4, or C5.
•
The subbands C1 and C2 cannot be chosen in conj unct ion wit h t he subbands
C, C3, C4, or C5.
•
The subbands C3, C4, and C5 cannot be chosen in conj unct ion wit h t he
subbands C, C1, or C2.
•
Up t o t wo non- cont iguous set s of subbands can be select ed, and t here m ust be
m ore t han a 5 MHz gap bet ween t he bands.
The PCS SuperDART support s t he following St art and St op frequencies:
•
The PCS RF SuperDART support s t he select ion of a St art and St op frequency
for t he passband as list ed in Table 19.
•
The PCS RF SuperDART St art and St op frequencies are in t he range of
1930MHz - 2000MHz.
UMTS SuperDART
You can select a St art and St op frequency for t he passband in t he frequency range
of 2110 MHz - 2170 MHz.
Page 80
© 2011 ADC Telecommunications, Inc
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
I nit ial FlexWave Prism Syst em Set up
DART Start and Stop Frequencies
Host SuperDARTs support t he select ion of a St art and St op frequency for t he
passband or for t he select ion of subbands ( up t o t wo st art - st op frequency pairs
m ay be select ed as long as t he t wo pairs are at least 5 MHz apart and one is lim it ed
t o 39 MHz and t he ot her is lim it ed t o 25 MHz) .
NOTE:
Start/Stop frequencies and subbands may not be used at the same time.
Table 22 list s t he support ed st art - st op frequency ranges for SuperDARTs.
Table 22.
Supported SuperDART Stop/Start Frequency Ranges
Frequency
Range
(MHz)
Timeslots
12
18
25
39
45
75
12
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
Page 81
© 2011 ADC Telecom m unicat ions, I nc.
Set t he Forward and Reverse Delays
SET THE FORWARD AND REVERSE DELAYS
NOTE:
The system comes up with a default delay. Once linking is complete, the system will
calculate the actual delay. The initial parameters that are set may therefore be out of
range. If necessary, correct the delay within the available range.
NOTE:
If part of a simulcast, ensure that all links in the simulcast are set to the same delay
value.
NOTE:
For information on the Linked DARTs Delay table at the bottom of the page, see “Using
the Linked DARTs Delay Table” on page 83.
To access t he Configure Delay page, in t he Syst em Menu bar, click System
Configuration > Configure Delay.
I n t he Remote Parameters t able, do t he following:
I n t he Remote Id list , select t he Rem ot e Unit for which you want t o configure
t he delay set t ings.
I n t he DART list , select t he DART for which you want t o configure t he delay
set t ings. Only t hose DARTS t hat have been linked will be available in t he
DART list . The following inform at ion is populat ed in t he Remote Parameters
t able, which corresponds t o t he Rem ot e Unit and DART t hat you have
select ed.
•
Forward Delay ( s) —t he Forward Range in m icroseconds available for t he
select ed DART
•
Forward Delay Range ( s) —t he Forward Delay Range in m icroseconds for
t he select ed DART
•
Reverse Delay ( s) —t he Reverse Delay in m icroseconds available for t he
select ed DART
•
Reverse Delay Range ( s) —t he Reverse Delay Range in m icroseconds for
t he select ed DART
•
Passband—t ype of passband provided by t he DART
I f necessary, change t he Forward Delay and t he Reverse Delay:
•
Forward Delay ( s) box—ent er t he act ual delay in m icroseconds t hat will
be applied t o t he RF forward pat h signal. The Forward Delay Range ( s) field
displays valid set t ings for t he Forward Delay.
•
Reverse Delay ( s) box—ent er t he act ual delay in m icroseconds t hat will
be applied t o t he RF reverse pat h signal. The Reverse Delay Range ( s) field
displays valid set t ings for t he Reverse Delay.
Page 82
© 2011 ADC Telecommunications, Inc
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
I nit ial FlexWave Prism Syst em Set up
Click Apply. The Operation complete m essage displays, and t he Remote Parameters
t able clears so you can set t he delay for anot her DART.
Repeat St ep 2 t hrough St ep 3 for each DART.
Using the Linked DARTs Delay Table
The Linked DARTs Delay t able provides t he following inform at ion:
•
Host colum ns—ident ifies t he Host in t he link
– DART Id—num ber of t he Host slot in which t he DART is inst alled
– DART Name—user- defined nam e for t he Host DART
•
Remote colum ns—ident ifies t he Rem ot e and it s elem ent s
– Id—Unit I D of PRU/ URU based upon layered address; see “ Unit
I dent ificat ion” on page 43
– Name—user- defined label for t he PRU/ URU
– DART Id—PRU/ URU slot num ber in which t he DART is inst alled
– DART Name—user- defined nam e for t he Rem ot e DART
– Forward Delay ( s) —user request ed FWD RF pat h delay in m icroseconds
– Reverse Delay ( s) —user request ed REV RF pat h delay in m icroseconds
•
Common colum ns—configurat ion set t ings com m on t o t he Host and Rem ot e( s)
– Passband—t ype of passband provided by t he DART.
– Frequency (MHz)—passband frequency of t he DART
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
Page 83
© 2011 ADC Telecom m unicat ions, I nc.
Set t he Forward and Reverse Delays
Filtering the Linked DARTs Delay Table
I n t he Filter panel View list , select a filt er t o be applied t o t he t able.
In the contains box, ent er filt er crit eria.
Click Filter t o apply t he filt er.
I n t he following exam ple, t he Linked DARTs Delay t able has been filt ered t o show
only t hose Host Unit s wit h a DART Id t hat cont ains “ 2” .
Page 84
© 2011 ADC Telecommunications, Inc
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
I nit ial FlexWave Prism Syst em Set up
CONFIGURE HOST FORWARD GAIN
NOTE:
Digital power measurements are inaccurate when ALC is active.
Follow t hese st eps t o set t he Forward Gain value for t he Host DART.
Det erm ine what t he Host DART Forward Gain should be. Use a signal generat or
and spect rum analyzer t o m easure t he uplink at t enuat ion from t he Host t o t he
BTS, and t he FWD power at t he Host from t he BTS t o det erm ine unloaded
power level.
The Host DART expect s signal levels from -25 t o +5 dBm. I f t he fully loaded signal
is + 5 dBm , t hen t he DART forward gain should be set t o 0 dB, if t he fully loaded
signal is - 25 dBm , t hen t he DART Forward Gain should be set t o 31 dB. The
equat ion is:
DART Forward Gain = 5 - fully Loaded Base St at ion Signal
CAUTION!
If you are setting up the system when no calls are going through, you must allow
headroom for a fully loaded forward path. For CDMA protocols, the difference from
unloaded to fully loaded is typically 8dB, so if the unloaded signal is -15dBm, then the
fully loaded input would be -7 dBm and the Host Forward Gain should be set to 5-(-7) = 12
dB.

The same rules applies for GSM carriers, except that the unloaded to loaded is
determined by the equation 10*log10(# RF Channels). So if there are 4 GSM RF Channels,
then the loaded forward path is 6 dB above unloaded.

If sufficient headroom is not present, then the LPA can be over-powered causing a Loss
Of Service.
CAUTION!
When configured correctly, the Host DART Forward input can handle peaks of 14dB above
the BTS signal level. For example, if the fully loaded CDMA carrier is -25dBm, then peaks
up to -11 dBm can be handled (CDMA peak to average is typically 10-12 dB). If the peaks
exceed the 14 dB of headroom, then Automatic Level Control (ALC) will occur to prevent
over-driving the A/D Converter.
NOTE:
In the EMS GUI, the reverse path gain range for Classic DARTs is 5 to 36 dB, which
indicates actual reverse path system gain. If you set this gain through the SNMP SET
commands, then the gain range is 0 to 31 dB, which maps to the actual GUI/system
reverse path gain range of 5 to 36 dB.
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
Page 85
© 2011 ADC Telecom m unicat ions, I nc.
Configure Host Forward Gain
I n t he EMS, do t he following t o set t he Host Forward Gain param et ers:
To access t he Configure Host Forward Gain page, in t he Syst em Menu bar, click
System Configuration > Configure Host Forward Gain.
I n t he Host Parameters t able DART list , select t he Host DART t hat you want t o
configure. Ot her inform at ion in t he Host Parameters t able is updat ed t o show
set t ings for t he select ed DART.
I n t he DART Mode list , select one of t he following:
•
Standby—forces t he RF funct ion t o be m ut ed in t he Host and it s linked
Rem ot e Unit .
•
Normal—allows t he syst em t o operat e norm ally ( RF funct ion not forced t o
be m ut ed) , assum ing all ot her syst em com ponent s are in proper working
order. ( Default set t ing.)
I n t he Fwd Gain (dB) list , select t he Forward Gain value of 0 t o 31 dB, based
upon t he fully loaded forward pat h signal level from t he Base St at ion.
I n t he Power Level Mode list , select one of t he following:
NOTE:
•
Snapshot—provides a “ snap- shot ” or current RF m easurem ent for t he
select ed Rem ot e Unit DART ( default set t ing) .
•
Max Hold—ret ains t he m axim um values for peak and peak average, and
t he m inim um values for m inim um average since t he last Max Hold Reset.
The Power Level Mode is disabled if the:
•
•
•
DART Operating mode is set to Standby
DART Pass Band (Timeslots) parameter is set to Undefined (default)
DART Diversity Status is set to Diversity.
Page 86
© 2011 ADC Telecommunications, Inc
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
I nit ial FlexWave Prism Syst em Set up
I f you set t he Power Level Mode t o Max Hold, you can click Reset Max Hold t o reset
t he Max Hold values. The Host Forward Gain Settings t able updat es wit h t he new
set t ings.
The Host Parameters t able provides t he following inform at ion:
•
Peak Power (dBm)—shows t he highest ( peak) power level reached by t he
Host DART
•
Average Power (dBm)—shows t he average power level reached by t he Host
DART
•
Minimum Power (dBm)—shows t he m inim um power level reached by t he
Host DART
Click Apply.
•
Once t he syst em execut es t he com m and, an Operation completed m essage
displays.
•
The Host Forward Gain Settings t able at t he bot t om of t he page is updat ed
wit h t he new set t ings.
Repeat St ep b on page 86 t hrough St ep g for each Host DART.
For inform at ion on t he Host Forward Gain Settings t able, see “ Viewing t he Host RF
Report ” on page 108.
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
Page 87
© 2011 ADC Telecom m unicat ions, I nc.
Configure Host Reverse Gain
CONFIGURE HOST REVERSE GAIN
When set t ing t he Reverse Gain value for t he Host DART, t he following rules m ust be
observed:
•
The Reverse Gain set t ing can be used t o overcom e RF int erfacing losses from t he
Host DART t o t he BTS/ BDA. I f you want unit y reverse pat h gain and t he losses
t o t he BTS/ BDA are 20 dB, t hen t he Reverse Gain should be set t o 20 dB.
•
Sim ulcast changes t he act ual REV gain level by 10log( n) where n = t he num ber
of sim ulcast links. For exam ple, if REV gain is set t o 10dB in a 2: 1 sim ulcast
configurat ion, t he act ual REV gain is only 7dB ( 10dB - 3dB) . I f REV gain is set
t o 20dB in a 4: 1 sim ulcast , t he act ual gain is 14dB ( 20dB - 6dB) .
Follow t hese st eps t o set t he Reverse Gain value for t he Host DART.
To access t he Configure Host Reverse Gain page, in t he Syst em Menu bar, click
System Configuration > Configure Host Reverse Gain.
I n t he Host Parameters t able DART list , select t he Host DART t hat you want t o
configure. The DART Name colum n is populat ed wit h t he user- defined nam e for
t he select ed DART.
I n t he Reverse Gain Mode list , select t he algorit hm t hat should be used t o add
at t enuat ion for a sim ulcast group t o prevent clipping because of t oo st rong a
signal.
•
Mode 1 (Noise Floor Matching)—opt im izes t he reverse pat h dynam ic range
bet ween sim ulcast nodes. For Prism / URU, t he gains are reduced by
10* log10( N) . This is t he default for syst em s running Prism EMS 7.1.
•
Mode 2 (Legacy Prism/URH)—reduces t he gain by 20* log10( N) . This is t he
default set t ing for syst em s upgraded from 6.0.
Set t he Additive Gain (dB) value t o achieve t he required gain from t he input t o t he
Rem ot e Unit t o t he out put of t he Host DART. The range is 0 t o 31 dB.
Page 88
© 2011 ADC Telecommunications, Inc
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
I nit ial FlexWave Prism Syst em Set up
I n t he Gain Mode list , select one of t he following:
•
Normal—no increase t o t he gain set t ing.
•
High—t he gain set t ings for Classic DARTs increase 2dB wit h a 1dB
im provem ent in t he Noise Figure and t he gain set t ing for SuperDart s
increase by 6 dB wit h a 2dB im provem ent in t he Noise Floor.
Click Apply. The Host Parameters and Host Reverse Gain Settings t ables are updat ed
wit h t he new configurat ion.
Repeat St ep 2 t hrough St ep 6 for each Host DART.
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
Page 89
© 2011 ADC Telecom m unicat ions, I nc.
Configure Host Reverse Gain
The Host Reverse Gain Settings t able has t he following colum ns.
•
DART Id—ident ifies t he Host DART by t he slot in which it is inst alled, which can
be from 1 t hrough 8.
•
DART Name—ident ifies t he DART by it s user- defined nam e.
•
Reverse Gain Mode—whet her t he Reverse Gain Mode is Mode 1 (Noise Floor Matching)
or Mode 2 (Legacy Prism/URH).
•
Additive Gain (dB)—gain from t he input t o t he Rem ot e Unit t o t he out put of t he
Host DART. The range is 0 t o 31 dB
•
Calculated Reverse System Gain (dB)—shows t he end- t o- end gain based on t he
addit ive gain, gain m ode, and num ber of Rem ot e Unit s in t he sim ulcast group.
•
Noise Floor (dBm/30kHz rbw)—shows t he noise level for t he configurat ion. The noise
floor is t he m easure of t he signal creat ed from t he sum of all t he noise sources.
•
Gain Mode—whet her t he Gain Mode is Normal or High.
•
Passband—t ype of passband provided by t he DART.
•
Frequency (MHz)—passband frequency of t he DART.
Page 90
© 2011 ADC Telecommunications, Inc
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
I nit ial FlexWave Prism Syst em Set up
CONFIGURE REMOTE FORWARD GAIN
To access t he Configure Remote Forward Gain page, in t he Syst em Menu bar, click
System Configuration > Configure Remote Forward Gain.
I n t he Remote Parameters t able, do t he following:
Use t he Host DART colum n t o ident ify t he connect ed Host .
I n t he Remote Id list , select t he Rem ot e Unit for which you want t o set t he
Forward Gain.
I n t he Remote DART Mode list , set t he DART m ode:
•
Standby—forces t he RF funct ion t o be m ut ed in t he Host and it s linked
Rem ot e Unit .
•
Normal—allows t he syst em t o operat e norm ally ( RF funct ion not forced t o
be m ut ed) , assum ing all ot her syst em com ponent s are in proper working
order. ( Default set t ing.)
I n t he LPA Mode list , select Normal. A Prism Linear Power Am plifier ( LPA) is a
high qualit y broadband RF am plifier used for achieving Prism product - rat ed
power for t he Rem ot e Tx forward pat h spect rum RF. I n a dual- LPA syst em ,
bot h LPAs will have t he sam e LPA Mode set t ing.
•
Standby—forces t he RF funct ion t o be m ut ed in t he Host and it s linked
Rem ot e Unit . ( Default set t ing.)
•
Normal—allows t he syst em t o operat e norm ally ( RF funct ion not forced t o
be m ut ed) , assum ing all ot her syst em com ponent s are in proper working
order.
CAUTION!
As soon as you set the LPA Operating Mode to Normal, RF transmission will start. Before
you set the LPA Operating Mode to Normal, make sure that the antenna has been
connected and the system is ready to transmit RF. For information on connecting the
antenna, refer to the ADC® FlexWave Prism Remote Unit Installation Guide
(ADCP-77-072).
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
Page 91
© 2011 ADC Telecom m unicat ions, I nc.
Configure Rem ot e Forward Gain
I n t he Forward Gain list , select t he dB ( 0 t o 31) .
The Forward Gain is t he act ual gain, not at t enuat ion, t hat will be applied t o
t he RF forward pat h signal ( where 0 = 0 dB gain, 1 = 1 dB gain, and so
fort h) . The Forward Gain is based on t he EI RP desired at t he ant enna. You
t herefore need t o know how m uch cable, insert ion, and any ot her loss ( such
as split t ers) exist bet ween t he Rem ot e Unit and t he ant enna. Set t he Forward
Gain t o achieve t he required out put power level t o m eet t he EI RP of your RF
link budget .
Configure t he Host DART gain t o achieve + 5dB so t hat full scale out put can
be achieved at t he Rem ot e. For furt her inform at ion, refer t o t he FlexWave
Prism com m issioning guide.
Refer t o t he following read- only fields for furt her inform at ion on t he
select ed PRU/ URU:
•
NOTE:
RF Power (dBm) colum n displays t he m easurem ent of t he RF power for t he
LPA ident ified in t he LPA Num ber field.
After a change in the DART Forward Gain, the EMS reflects the change in the RF Power
column within 25 seconds, or if the Refresh button is used, within 12 seconds.
•
Max Power (dBm) colum n displays t he m axim um LPA power values.
•
VSWR colum n displays t he Volt age St anding Wave Rat io ( VSWR) for t he
LPA. An LPA VSWR Fault occurs if t he VSWR m easurem ent exceeds t he
t hreshold, which is 3: 1.
Page 92
© 2011 ADC Telecommunications, Inc
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
I nit ial FlexWave Prism Syst em Set up
Click Apply.
•
Once t he syst em execut es t he com m and, an Operation completed m essage
displays.
•
The Remote Forward Gain t able at t he bot t om of t he page is updat ed wit h
t he new set t ings.
Repeat for each PRU/ URU DART.
For addit ional inform at ion, refer t o t he following:
•
For inform at ion on t he Remote Forward Gain Settings t able, see “ Viewing t he
Rem ot e RF Report ” on page 109.
•
For inform at ion on t he LPA Reset but t on, see “ Reset t ing an LPA” on page 165.
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
Page 93
© 2011 ADC Telecom m unicat ions, I nc.
Configure Reverse I nput Power Levels
CONFIGURE REVERSE INPUT POWER LEVELS
NOTE:
Digital power measurements are inaccurate when ALC is active.
To access t he Configure Reverse Input Power Levels page, in t he Syst em Menu bar,
click System Configuration > Configure Reverse Input Power Levels.
The read- Only colum ns in t he t able provide t he following inform at ion:
•
Peak Power (dBm)—shows t he highest ( peak) power level reached by t he DART
•
Average Power (dBm)—shows t he average power level reached by t he DART
•
Minimum Power (dBm)—shows t he m inim um power level reached by t he DART
•
Last Max Hold Reset Time—shows t he last t im e MAX Hold was reset .
•
Passband—t ype of passband provided by t he DART
•
Frequency (MHz)—passband frequency of t he DART
I n t he Select Remote list , select t he PRU/ URU t hat you are configuring. The t able
at t he bot t om of t he page displays power level values for t he select ed Rem ot e
Unit and it s DARTs.
I n t he Select DART list , do one of t he following:
•
Select a specific DART t o configure. I f you select a specific DART, t he t able
at t he bot t om of t he page displays power level values for t he select ed DART.
•
Select All t o configure all t he DARTs t he sam e at t he sam e t im e. I f you select
All, t he t able at t he bot t om of t he page displays power level values for t he
select ed Rem ot e Unit and all it s DARTs.
I n t he Gain Mode list , set t he High Gain m ode t o one of t he following:
•
Normal—effect s t he at t enuat ion of t he t em perat ure com pensat ion algorit hm
( default ) .
•
High—does not effect t he at t enuat ion of t he t em perat ure com pensat ion
algorit hm .
NOTE:
When a Classic DART is in High Gain mode, the noise floor increases by 1 dBm. When a
Super DART is in High Gain mode, the noise floor increases by 4 dBm.
Page 94
© 2011 ADC Telecommunications, Inc
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
I nit ial FlexWave Prism Syst em Set up
I n t he Power Level Mode list , select one of t he following:
•
Snapshot—provides a “ snap- shot ” or current RF m easurem ent for t he
select ed Rem ot e Unit DART ( default set t ing) .
•
Max Hold—ret ains t he m axim um values for peak and peak average, and t he
m inim um values for m inim um average since t he last Max Hold Reset.
Power Level Mode is disabled under any of t he following condit ions:
•
if t he DART Operating m ode is set t o Standby
•
if t he DART Pass Band (Timeslots) param et er is set t o Undefined ( default )
Click Apply.
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
Page 95
© 2011 ADC Telecom m unicat ions, I nc.
Configure Reverse I nput Power Levels
( Opt ional) I f you set t he Power Level Mode t o Max Hold, you can click Reset Max Hold
t o reset t he Max Hold values.
Page 96
© 2011 ADC Telecommunications, Inc
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
P ART I I I
SYSTEM MANAGEMENT
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
Page 97
© 2011 ADC Telecom m unicat ions, I nc.
I nt ent ionally Blank Page
Page 98
© 2011 ADC Telecommunications, Inc
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
SYSTEM INFORMATION
Topics
Page
Get I nform at ion ................................................................................................................... 100
Accessing Syst em Report s ............................................................................................... 101
Viewing t he Soft ware/ Firm ware Report ........................................................................ 101
Viewing t he Hardware I nvent ory Report ....................................................................... 102
Viewing t he Net work Report ....................................................................................... 104
Viewing t he Linked DARTs Report ................................................................................ 105
Viewing t he Delay Report ........................................................................................... 106
Viewing t he Fiber Report ............................................................................................ 107
Viewing t he Host RF Report ........................................................................................ 108
Viewing t he Rem ot e RF Report .................................................................................... 109
Viewing t he Alarm s Report ......................................................................................... 110
I FEU + RAU Report ................................................................................................... 111
Viewing t he All Report ............................................................................................... 112
Downloading a Report ..................................................................................................... 113
Get Opt ics I nform at ion ......................................................................................................... 116
Get Logs ............................................................................................................................. 118
This sect ion t ells you how t o get and m anage syst em inform at ion.
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
Page 99
© 2011 ADC Telecommunications, Inc.
Get I nform at ion
G ET I NFORMATION
The Get Information page allows you t o view syst em inform at ion on one page. You
can also view and download nine individual report s.
To access t he Get Information page, in t he Syst em Menu bar, click System Information >
Get Information.
The following graphic shows t he default page in which Type is set t o System Inventory.
The Get Information page has t he following elem ent s:
•
Type list —allows you t o select which report you want t o view.
•
Download but t on—downloads select ed
“ Downloading a Report ” on page 113.
NOTE:
report
to
an
at t ached
PC.
See
The gray and white status bar at the top of the page indicates that the EMS is accessing
the requested report. You do not need to select Download to see the report in the GUI.
Page 100
© 2011 ADC Telecommunications, Inc
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
Syst em I nform at ion
Accessing System Reports
You use t he Type list in t he Reports panel t o select t he t ype of report t hat you want
t o download. The following sect ions describe t he report s t hat you can view and
download.
Viewing the Software/Firmware Report
To access t he Software/Firmware report , in t he Syst em Menu bar, click System
Information > Get Information, and t hen in t he Reports panel Type list , select
Software/Firmware. ( This is t he default set t ing.)
The Software/Firmware t able provides t he following inform at ion:
•
Module Type—t ype of unit ( Host , PRU, or URU) .
•
Name—user- assigned nam e for t he unit .
•
Unit Id—ident ifies t he unit wit hin t he syst em ; see “ Unit I dent ificat ion” on
page 43.
•
Version—version of inst alled soft ware/ firm ware.
•
Upgrade Status—t he following st at es can be seen. However, wit h t he except ion of
Normal operation and Upgraded, t he st at es occur very quickly during t he
corresponding act ion and are rarely viewed.
– Normal operation
– Upgrading
– Upgrading reboot
– Committing
– Aborting
– Recovering
– Upgraded.
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
Page 101
© 2011 ADC Telecom m unicat ions, I nc.
Get I nform at ion
Viewing the Hardware Inventory Report
To access t he Hardware Inventory report for t he Host and Rem ot e Unit ( s) , in t he
Syst em Menu bar, click System Information > Get Information, and t hen in t he Reports
panel Type list , select Hardware Inventory.
Page 102
© 2011 ADC Telecommunications, Inc
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
Syst em I nform at ion
The Hardware Inventory page has separat e t ables for each Host and Rem ot e Unit in
t he syst em . For each Rem ot e Unit list ed, t here is also a corresponding LPA t able.
Each unit is ident ified by nam e and I P address in a t it le bar at t he t op of t he t able.
Each t able provides t he following inform at ion:
•
Module Type—ident ifies t he m odule by t ype, such as Syst em Card, DART, SeRF
( not used in t he LPA t able) .
•
Module Number ( LPA t able only) —ident ifies t he LPA.
•
Id—applicable t o t he DARTs and LPAs only; for furt her inform at ion see “ RF
Module Capabilit ies and GUI Represent at ion” on page 21.
•
Date Code—dat e code for t he m odule.
•
Hardware Version—release version num ber for t he m odule.
•
Serial Number—serial num ber for t he m odule assigned during m anufact uring.
•
Part Number—Part Num ber for t he m odule assigned during m anufact uring ( not
applicable t o t he LPA) .
•
Description ( LPA only) —band t ype of LPA/ LPA power in Wat t s.
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
Page 103
© 2011 ADC Telecom m unicat ions, I nc.
Get I nform at ion
Viewing the Network Report
To access t he Network report , in t he Syst em Menu bar, click System Information > Get
Information, and t hen in t he Reports panel Type list , select Network.
The Network Statistics t able provides t he following inform at ion:
•
Unit Id—ident ifies t he unit wit hin t he syst em ; see “ Unit I dent ificat ion” on
page 43.
•
Port—ident ifies t he port
– Host port s can be any of t he following:

Net work Port

Craft Port

Swit ch Port
– Rem ot e Unit port is indicat ed only as a Swit ch Port
NOTE:
A Switch Port is the CPU’s connection to the Ethernet switch that in turn communicates to
the fibers. This shows how much traffic the unit is generating and consuming.
•
Rx Bytes—count of Receive Byt es.
•
Rx Packets—count of Receive Packet s.
•
RX FCS Errors—count of Receive FCS Errors.
•
Tx Bytes—count of Transm it Byt es.
•
Tx Packets—count of Transm it Packet s.
Page 104
© 2011 ADC Telecommunications, Inc
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
Syst em I nform at ion
Viewing the Linked DARTs Report
To access t he Linked DARTs report , in t he Syst em Menu bar, click System Information >
Get Information, and t hen in t he Reports panel Type list , select Link.
The Linked DARTs t able provides t he following inform at ion:
•
Host colum ns—ident ifies t he Host and it s elem ent s
– DART Id—num ber of t he Host slot in which t he DART is inst alled
– DART Name—user- defined nam e for t he Host DART
– SFP Id—port num ber of physical opt ical port where Host - Rem ot e opt ical fiber
is connect ed on t he Host .
– SFP Name—user- defined nam e for t he Opt ics port .
•
Remote colum ns—ident ifies t he Rem ot e and it s elem ent s
– Id—Unit I D of PRU/ URU based upon layered address; see “ Unit
I dent ificat ion” on page 43
– Name—user- defined label for t he PRU/ URU
– SFP Id—ident ificat ion ( I d) of Rem ot e side SFP connect ed t oward t he Host
DART ( can be from 1 t hrough 8)
– SFP Name—user- defined nam e for t he Opt ics port
– DART Id—PRU/ URU slot num ber in which t he DART is inst alled
– DART Name—user- defined nam e for t he Rem ot e DART
– Timeslots—num ber of t im eslot s assigned t o t he link.
•
Common colum ns—ident ify configurat ion set t ings t hat are com m on t o t he Host
and connect ed Rem ot e( s)
– Passband—t ype of passband provided by t he DART
– Frequency—passband frequency of t he DART
– Diversity—whet her DART is configured as Diversity or Non Diversity. For t his
release, t his will always be Non Diversity.
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
Page 105
© 2011 ADC Telecom m unicat ions, I nc.
Get I nform at ion
Viewing the Delay Report
To access t he Linked DARTs Delay report , in t he Syst em Menu bar, click System
Information > Get Information, and t hen in t he Reports panel Type list , select Delay.
The Linked DARTs Delay t able provides t he following inform at ion:
•
Host colum ns—ident ifies t he Host in t he link
– DART Id—num ber of t he Host slot in which t he DART is inst alled
– DART Name—user- defined nam e for t he Host DART.
•
Remote colum ns—ident ifies t he Rem ot e and it s elem ent s
– Id—Unit I D of PRU/ URU based upon layered address; see “ Unit
I dent ificat ion” on page 43
– Name—user- defined label for t he PRU/ URU
– DART Id—PRU/ URU slot num ber in which t he DART is inst alled
– DART Name—user- defined nam e for t he Rem ot e DART
– Forward Delay ( s) —user request ed FWD RF pat h delay in m icroseconds
– Reverse Delay ( s) —user request ed REV RF pat h delay in m icroseconds.
•
Common colum ns—ident ify configurat ion set t ings t hat are com m on t o t he Host
and connect ed Rem ot e( s)
– Passband—t ype of passband provided by t he DART
– Frequency (MHz)—passband frequency of t he DART.
Page 106
© 2011 ADC Telecommunications, Inc
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
Syst em I nform at ion
Viewing the Fiber Report
To access t he Fiber Optics report , in t he Syst em Menu bar, click System Information >
Get Information, and t hen in t he Reports panel Type list , select Fiber.
The Fiber Optics t able provides t he following inform at ion:
•
Unit Type—what t he unit is, such as Host or Rem ot e.
•
Unit Name—Unit I D of t he unit based upon layered address; see “ Unit
I dent ificat ion” on page 43.
•
SFP Number—Opt ical port num ber, from 1 t o 8.
•
SFP Name—nam e assigned
UNKNOWN_SFPNAME.
•
Optics Type
– LongRange—26 dB
– IntermediateRange—18 dB) .
•
Wavelength (nm)—wave lengt h t ransm it t ed t hrough t his port :
– Non- duplex and WDM configurat ions: 1550 nm fwd, 1310 nm rev
– CWDM configurat ions can be one of eight wavelengt hs: 1470 nm , 1490 nm ,
1510 nm , 1530 nm , 1550 nm , 1570 nm , 1590 nm , and 1610 nm .
•
Tx Power (dBm)—launch power level in dBm of forward pat h signal. The m inim um
FWD launch power is - 2 dBm , and t he m axim um is 3 dBm .
•
Rx Power (dBm)—receive power level in dBm of reverse pat h signal, which
incorporat es t he launch power of t he Rem ot e Unit SFP plus all opt ical losses
( insert ion losses, fiber cable loss, and so fort h) .
•
Remote Name—nam e of t he Rem ot e connect ed t o t his Opt ical port .
•
Alarm Status—whet her an alarm is act ive. I f an alarm is act ive, t here will be a
Minor or Major link t hat you click t o open a dialog t hat defines t he act ive alarm ,
as described in “ Viewing Alarm Det ails” on page 45. The background color of
t he Alarm Status cell also indicat es t he alarm level ( see “ Alarm Color Codes” on
page 44) .
to
t he
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
Opt ical
port ;
default
SFP Name
is
Page 107
© 2011 ADC Telecom m unicat ions, I nc.
Get I nform at ion
Viewing the Host RF Report
To access t he Host Forward Gain Settings report , in t he Syst em Menu bar, click System
Information > Get Information, and t hen in t he Reports panel Type list , select Host RF.
The Host Forward Gain Settings t able provides t he following inform at ion.
•
DART Id—num ber of t he Host slot in which t he DART is inst alled
•
DART Name—user- defined nam e for t he Host DART
•
DART Mode—ident ifies t he RF funct ion
– Standby—RF funct ion is m ut ed in t he Host and it s linked Rem ot e Unit .
– Normal—RF funct ion not forced t o be m ut ed, allows t he syst em t o operat e
norm ally
•
Fwd Gain (db)—Forward Gain in decibels assigned t o t he DART
•
Power Level Mode—Host DART I nput Power Level Mode:
– Snapshot—provides a “ snap- shot ” or current RF m easurem ent for t he
select ed Rem ot e DART ( default set t ing) .
– Max Hold—ret ains t he m axim um values for peak and peak average, and t he
m inim um values for m inim um average since t he last Max Hold Reset.
NOTE:
The Power Level Mode is disabled if the:
•
DART Operating mode is set to Standby
•
DART Pass Band (Timeslots) parameter is set to Undefined (default)
•
DART Diversity Status is set to Diversity.
•
Peak Power (dBm)—highest level of power experienced on t he DART Forward link.
•
Average Power (dBm)—average power experienced on t he DART Forward link.
•
Minimum Power (dBm)—average m inim um power experienced on t he DART
Forward link.
•
Last Max Hold Reset Time—t im e t hat Max Hold was last reset .
•
Passband—t ype of passband provided by t he DART.
•
Frequency (MHz)—passband frequency of t he DART
Page 108
© 2011 ADC Telecommunications, Inc
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
Syst em I nform at ion
Viewing the Remote RF Report
To access t he Remote Forward Gain Settings report , in t he Syst em Menu bar, click System
Information > Get Information, and t hen in t he Reports panel Type list , select Remote RF.
The Remote Forward Gain Settings t able provides t he following inform at ion:
•
Host colum ns—ident ifies t he Host in t he link
– DART Id—num ber assigned by t he EMS t o t he Host DART for ident ificat ion
purposes
– DART Name—user- defined nam e for t he DART.
•
Remote colum ns—ident ifies t he Rem ot e and it s elem ent s
– DART Id—Unit I D of PRU/ URU based upon layered address; see “ Unit
I dent ificat ion” on page 43
– DART Name—user- defined label for t he PRU/ URU
– DART Mode—how RF funct ions on t hat DART
•
Standby—forces t he RF funct ion t o be m ut ed in t he Host and it s linked
Rem ot e.
Normal—allows t he syst em t o operat e norm ally ( RF funct ion not forced t o
be m ut ed) , assum ing all ot her syst em com ponent s are in proper working
order. ( Default set t ing.)
Forward Gain (db)—act ual gain, not at t enuat ion, applied t o t he RF forward pat h
signal ( where 0 = 0 dB gain, 1 = 1 dB gain, and so fort h)
RF Power (dBm)—est im at ed power level based upon input level and gain.
Max Power (dBm)—t he m axim um LPA power values
VSWR—t he Volt age St anding Wave Rat io ( VSWR) for t he LPA. An LPA VSWR
Fault occurs if t he VSWR m easurem ent exceeds t he t hreshold, which is 3: 1.
LPA Mode—t he LPA Mode, which can be Normal or Standby
LPA Status—t he LPA st at us. I n case of dual LPA, it will indicat e t he value for
bot h LPAs as eit her 1-Offline or 2-Operating.
•
–
–
–
–
–
–
•
Passband—t ype of passband provided by t he DART
•
Frequency (MHz)—passband frequency of t he DART
FlexWave Prism Elem ent Managem ent Syst em 7.1 User Manual
ADCP- 77- 177 • I ssue 1 • July 2011
Page 109
© 2011 ADC Telecom m unicat ions, I nc.
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Extract, Print high-res
Author                          : TE106558
Create Date                     : 2011:12:06 13:34:28-08:00
Modify Date                     : 2011:12:06 13:37:12-08:00
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Metadata Date                   : 2011:12:06 13:37:12-08:00
Creator Tool                    : FrameMaker 7.1
Format                          : application/pdf
Title                           : ADC FlexWave Prism Element Management System 7.1 User Manual
Creator                         : TE106558
Document ID                     : uuid:c5a66eaa-6632-46e6-8f7a-0a43299fc342
Instance ID                     : uuid:95ad8d69-bb4c-40bc-8439-325f6167349a
Producer                        : Acrobat Distiller 9.4.5 (Windows)
Page Count                      : 65
EXIF Metadata provided by EXIF.tools
FCC ID Filing: F8I-PSM0804A

Navigation menu