ADTRAN TRC6410L2X TRACER 6410 User Manual TRACER 6000 Series Integrated System Manual

Adtran TRACER 6410 TRACER 6000 Series Integrated System Manual

Users Manual

Download: ADTRAN TRC6410L2X TRACER 6410 User Manual TRACER 6000 Series Integrated System Manual
Mirror Download [FCC.gov]ADTRAN TRC6410L2X TRACER 6410 User Manual TRACER 6000 Series Integrated System Manual
Document ID696397
Application IDBuhVefKUCNIvTG8MdXPftw==
Document DescriptionUsers Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize151.75kB (1896888 bits)
Date Submitted2006-08-22 00:00:00
Date Available2006-08-22 00:00:00
Creation Date2005-09-16 13:38:18
Producing SoftwareAcrobat Distiller 6.0 (Windows)
Document Lastmod2006-07-21 11:32:08
Document TitleTRACER 6000 Series Integrated System Manual
Document CreatorFrameMaker 7.0
Document Author: ADTRAN, Inc.

TRACER 6000 SERIES
Integrated System Manual
12806410L2XA
TRACER 6410 2.4 GHz (High Power) System (Plan A)
12806410L2XB
TRACER 6410 2.4 GHz (High Power) System (Plan B)
12806420L1A
TRACER 6420 5.8 GHz System (Plan A)
12806420L1B
TRACER 6420 5.8 GHz System (Plan B)
612806420L1-1D
September 2005
Trademarks
TRACER 6000 Series Integrated System Manual
Trademarks
Any brand names and product names included in this manual are trademarks, registered trademarks, or
trade names of their respective holders.
To the Holder of the Manual
The contents of this manual are current as of the date of publication. ADTRAN reserves the right to change
the contents without prior notice.
In no event will ADTRAN be liable for any special, incidental, or consequential damages or for
commercial losses even if ADTRAN has been advised thereof as a result of issue of this publication.
About this Manual
This manual provides a complete description of the TRACER 64x0 systems (TRACER 6410 and 6420)
and system software. The purpose of this manual is to provide the technician, system administrator, and
manager with general and specific information related to the planning, installation, operation, and
maintenance of the TRACER 64x0 systems. This manual is arranged so that needed information can be
quickly and easily found.
901 Explorer Boulevard
P.O. Box 140000
Huntsville, AL 35814-4000
Phone: (256) 963-8000
Copyright © 2005 ADTRAN, Inc.
All Rights Reserved.
Printed in U.S.A.
Copyright © 2005 ADTRAN, Inc.
612806420L1-1D
TRACER 6000 Series Integrated System Manual
Revision History
Revision History
Document
Revision
Date
Description of Changes
December 2004
Initial release of manual to include the TRACER 6420 (5.8 GHz
integrated system) and the Quad T1 and Ethernet Switch modules.
March 2005
Include E1 and E1 breakout panel information and add new RF link
management bridge functionality. Update the Troubleshooting
Guide to include E1 information.
June 2005
Added new real-time power reporting and support for new
Quad E1 (120Ω) module.
September 2005
Include information for new product offering (TRACER 6410
2.4 GHz (High Power) system).
Notes provide additional useful information.
Cautions signify information that could prevent service interruption or damage to
equipment.
Warnings provide information that could prevent endangerment to human life.
612806420L1-1D
Copyright © 2005 ADTRAN, Inc.
Safety Instructions
TRACER 6000 Series Integrated System Manual
Safety Instructions
When using your telephone equipment, please follow these basic safety precautions to reduce the risk of
fire, electrical shock, or personal injury:
1. Do not use this product near water, such as a bathtub, wash bowl, kitchen sink, laundry tub, in a
wet basement, or near a swimming pool.
2. Avoid using a telephone (other than a cordless-type) during an electrical storm. There is a remote
risk of shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
4. Use only the power cord, power supply, and/or batteries indicated in the manual. Do not dispose of
batteries in a fire. They may explode. Check with local codes for special disposal instructions.
Save These Important Safety Instructions
Copyright © 2005 ADTRAN, Inc.
612806420L1-1D
TRACER 6000 Series Integrated System Manual
FCC-Required Information
FCC-Required Information
Federal Communications Commission Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio frequencies. Operation of this equipment in a
residential area is likely to cause harmful interference, in which case the user will be required to correct the
interference at his own expense.
Shielded cables must be used with this unit to ensure compliance with Class A FCC limits.
Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Radio Frequency Interface Statement
This equipment has been tested and found to comply with the limits for an intentional radiator, pursuant to
Part 15, Subpart C of the FCC Rules. This equipment generates, uses, and can radiate radio frequency
energy. If not installed and used in accordance with the instructions, it may cause interference to radio
communications.
The limits are designed to provide reasonable protection against such interference in a residential situation.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause interference to radio or television reception, which can be determined by turning the equipment
on and off, the user is encouraged to try to correct the interference by one or more of the following
measures:
•
•
•
•
Reorient or relocate the receiving antenna of the affected radio or television.
Increase the separation between the equipment and the affected receiver.
Connect the equipment and the affected receiver to power outlets on separate circuits.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by ADTRAN could void the user’s
authority to operate the equipment.
612806420L1-1D
Copyright © 2005 ADTRAN, Inc.
FCC-Required Information
TRACER 6000 Series Integrated System Manual
FCC Output Power Restrictions
The FCC does not require licensing to implement this device. License-free operation in the industrial,
scientific, and medical band is documented in FCC Rules Part 15.247. It is the responsibility of the
individuals designing and implementing the radio system to ensure compliance with any pertinent FCC
Rules and Regulations. This device must be professionally installed.
The FCC specifies the maximum transmitter power used for antennae of a given gain. FCC Rules Part 15,
Subpart 247 allow for a maximum power of 1 watt (30 dBm) into antennae of a gain less than or equal to 6
dBi. At 2.4 GHz (TRACER 6410), the 1-watt maximum transmitter power must be reduced by 1 dB for
every 3 dB of antenna gain over 6 dBi. This rule is shown in Table 5 on page 20. For the 5.8 GHz band
(TRACER 6420), the maximum output power is 1 watt (30 dBm) regardless of the gain of the attached
antenna. Since the TRACER 6420 maximum transmit power is 100 milliwatts, there is reduction in
transmitter output power required.
Exposure to Radio Frequency Fields
The TRACER 6410 is designed to operate at 2.4 GHz with 500 mW maximum transmit power, and the
TRACER 6420 is designed to operate at 5.8 GHz with 100 mW maximum transmit power.
This level of RF energy is below the Maximum Permissible Exposure (MPE) levels specified in FCC OET
65:97-01. The installation of high gain antenna equipment in the system configuration may create the
opportunity for exposure to levels higher than recommended for the general population at a distance less
than 15 feet (4.6 meters) from the center of the antenna. The following precautions must be taken
during installation of this equipment:
Verify the antenna installation meets all regulations specified in the National Electric
Code (NEC) Article 810 with particular attention to clearances from power and lighting
conductors, mounting, grounding, and antenna discharge unit.
•
•
•
•
•
•
•
The installed antenna must not be located in a manner that allows exposure of the general population to
the direct beam path of the antenna at a distance less than 15 feet (4.6 meters). Installation on towers,
masts, or rooftops not accessible to the general population is recommended; or
Mount the antenna in a manner that prevents any personnel from entering the area within 15 feet
(4.6 meters) from the front of the antenna.
It is recommended that the installer place radio frequency hazard warnings signs on the barrier that
prevents access to the antenna.
Prior to installing the antenna to the TRACER output, make sure the power is adjusted to the settings
specified in Section 2 of this manual.
During antenna installation, be sure that power to the TRACER equipment is turned off in order to
prevent the presence of microwave energy on the coaxial connector.
During installation and alignment of the antenna, do not stand in front of the antenna assembly.
During installation and alignment of the antenna, do not handle or touch the front of the antenna.
Per Industry Canada RSS210: “The installer of this radio equipment must ensure that the antenna is located
or pointed such that it does not emit RF field in excess of Health Canada limits for the general population;
consult Safety Code 6, obtainable from Health Canada’s website at www.hc-sc.gc.ca/rpb.These simple
precautions must be taken to prevent general population and installation personnel from exposure to RF
energy in excess of specified MPE levels.
Copyright © 2005 ADTRAN, Inc.
612806420L1-1D
TRACER 6000 Series Integrated System Manual
Warranty and Customer Service Information
Warranty, Customer Service, Product Support Information, and Training
ADTRAN will repair and return this product within the warranty period if it does not meet its published
specifications or fails while in service. Warranty information can be found at www.adtran.com/warranty.
A return material authorization (RMA) is required prior to returning equipment to ADTRAN. For service,
RMA requests, training, or more information, use the contact information given below.
Repair and Return
If you determine that a repair is needed, please contact our Customer and Product Service (CaPS)
department to have an RMA number issued. CaPS should also be contacted to obtain information
regarding equipment currently in house or possible fees associated with repair.
CaPS Department
(256) 963-8722
Identify the RMA number clearly on the package (below address), and return to the following address:
ADTRAN Customer and Product Service
901 Explorer Blvd. (East Tower)
Huntsville, Alabama 35806
RMA # _____________
Pre-Sales Inquiries and Applications Support
Your reseller should serve as the first point of contact for support. If additional pre-sales support is needed,
the ADTRAN Support website provides a variety of support services such as a searchable knowledge base,
latest product documentation, application briefs, case studies, and a link to submit a question to an
Applications Engineer. All of this, and more, is available at:
http://support.adtran.com
When needed, further pre-sales assistance is available by calling our Applications Engineering
Department.
Applications Engineering (800) 615-1176
612806420L1-1D
Copyright © 2005 ADTRAN, Inc.
Warranty and Customer Service Information
TRACER 6000 Series Integrated System Manual
Post-Sale Support
Your reseller should serve as the first point of contact for support. If additional support is needed, the
ADTRAN Support website provides a variety of support services such as a searchable knowledge base,
updated firmware releases, latest product documentation, service request ticket generation and
trouble-shooting tools. All of this, and more, is available at:
http://support.adtran.com
When needed, further post-sales assistance is available by calling our Technical Support Center. Please
have your unit serial number available when you call.
Technical Support
(888) 4ADTRAN
Training
The Enterprise Network (EN) Technical Training Department offers training on our most popular
products. These courses include overviews on product features and functions while covering applications
of ADTRAN's product lines. ADTRAN provides a variety of training options, including customized
training and courses taught at our facilities or at your site. For more information about training, please
contact your Territory Manager or the Enterprise Training Coordinator.
Training Phone
(800) 615-1176, ext. 7500
Training Fax
(256) 963-6700
Training Email
training@adtran.com
Copyright © 2005 ADTRAN, Inc.
612806420L1-1D
TRACER 6000 Series Integrated System Manual
Table of Contents
Table of Contents
Section 1
System Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
This section of ADTRAN’s TRACER 6000 Series Integrated System Manual is designed for
use by network engineers, planners, and designers for overview information about the TRACER
64x0 systems.
Section 2
Microwave Path Engineering Basics . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Explains the basics of analyzing a wireless microwave link or path. Defines significant
parameters and makes several installation recommendations.
Section 3
Engineering Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Provides information to assist network designers with incorporating the TRACER 64x0 system
into their networks.
Section 4
Network Turnup Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Provides shipment contents list, grounding instructions, mounting options, and specifics of
supplying power to the unit.
Section 5
User Interface Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Provides detailed descriptions of all menu options and configuration parameters available for
the
TRACER 64x0.
Section 6
Detail Level Procedures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Provides detailed instructions on performing common system tasks such as connecting to the
system and upgrading firmware.
DLP-1
Connecting a VT100 Terminal or PC to the CRAFT Port . . . . . . . . . . . . . . . . . . . . . . 91
DLP-2
Logging into the TRACER 64x0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
DLP-3
Setting IP Parameters for the TRACER 64x0. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
DLP-4
Verifying Communications Over an IP LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
DLP-5
Updating the Firmware Using TFTP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
DLP-6
Updating the Firmware Using XMODEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Section 7
MIBs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Provides a listing of SNMP Management Information Bases (MIBs) supported by the TRACER
64x0. This section also lists traps supported for each MIB.
Section 8
Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Provides helpful information for troubleshooting common configuration problems for the
TRACER 64x0.
612806420L1-1D
Copyright © 2005 ADTRAN, Inc.
Table of Contents
10
TRACER 6000 Series Integrated System Manual
Copyright © 2005 ADTRAN, Inc.
612806420L1-1D
SYSTEM DESCRIPTION
This section of ADTRAN’s TRACER 6000 Series Integrated System Manual is designed for use by
network engineers, planners, and designers for overview information about the TRACER 64x0 systems.
It contains general information and describes physical and operational concepts, network relationships,
provisioning, testing, alarm status, and system monitoring. This section should be used in conjunction with
Section 3, Engineering Guidelines, of this manual.
CONTENTS
System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Features and Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Configuration and Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Operational . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Available Interface Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
E1 Network Module with 120Ω Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
E1 Network Module with 75Ω Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
T1 Network Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Quad Ethernet Switch Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
612806420L1-1D
Copyright © 2005 ADTRAN, Inc.
11
Section 1 System Description
1.
TRACER 6000 Series Integrated System Manual
SYSTEM OVERVIEW
The TRACER 64x0 provides license-free scalable connectivity for service providers and corporate
networks. These radios feature two modular network interface ports that can accommodate various
combinations of T1, E1, and Ethernet option cards up to 8xT1/E1 (16.384 Mbps). This flexibility provides
customized time division multiplexed (TDM) and packet solutions for voice and data applications in a
single platform. The TRACER 6410 and TRACER 6420 provide carrier class point-to-point connectivity
up to thirty miles in the 2.4 GHz and 5.8 GHz license-free Industrial, Scientific, and Medical (ISM) bands,
respectively.
Complete network management is supported via simple network management protocol (SNMP), Telnet
access, and a VT100 terminal interface (CRAFT port). SNMP traps are implemented for all RF link and
T1/E1/Ethernet alarm conditions, enabling remote installations to report outages without requiring a truck
roll to diagnose problems. Version 2 standard management information bases (MIBs) are supported for all
interface cards, while an enterprise-specific MIB is provided for radio functionality. Triple-DES (3DES)
security provides additional protection from unauthorized access without requiring any additional external
security appliances. Encryption can also be disabled altogether. Future upgrades and enhancements can be
added through FLASH firmware downloads via trivial file transfer protocol (TFTP) (on the Ethernet
interface) or XMODEM on the CRAFT port.
Receive sensitivity is optimized through the use of extensive forward error correction and
high-performance receiver design techniques. Dynamic receive sensitivity allows the user to increase
receiver performance by decreasing the delivered bandwidth. This feature maximizes link performance by
customizing the delivered bandwidth to the specific needs of the installation. Three software selectable
channel plans are supported to simplify frequency coordination at co-located sites. Channel plans are
easily changed via any of the software management interfaces without the added expense of hardware
upgrades or spare filter assemblies.
TRACER 64x0 wireless solutions maximize equipment density through the combination of compact size
(only 1U rack space required), low power consumption, and high thermal transfer. TRACER 64x0 systems
can be deployed at twice the density of other available wireless products.
2.
FEATURES AND BENEFITS
The following is a brief list of the TRACER 64x0 features and benefits:
Configuration and Management
•
•
•
Easy-to-use VT100 control port (RS-232 interface) for configuration and monitoring
End-to-end management bridging for forwarding management traffic across the RF link management
channel
Remote configuration of both ends of the wireless link, from each end of the link
Operational
•
•
•
•
•
12
No license required per FCC Rules Part 15.247
Dual module slots for network connectivity
Up to 8xT1 or E1 bandwidth (16.384 Mbps) using two 4xT1 or 4xE1 network modules
TRACER 6410 Frequency: 2.400 to 2.483 GHz
TRACER 6420 Frequency: 5.725 to 5.850 GHz
Copyright © 2005 ADTRAN, Inc.
612806420L1-1D
TRACER 6000 Series Integrated System Manual
•
•
Section 1 System Description
Point-to-point transmission, up to 30 miles
1U high unit for easy rack mounting
Available Interface Modules
•
•
•
•
Quad T1 Module (P/N 1280040L1)
Quad E1 Module with 120Ω Interface (P/N 1280044L1)
Quad E1 Module with 75Ω Interface (P/N 1280044L2)
Quad Ethernet Switch Module (P/N 1280050L1)
E1 Network Module with 120Ω Interface
•
•
•
•
Four E1 circuits provided through four RJ-45 connectors
Complies with CCITT G.703, G.704, and G.823 standards
E1 circuit alarm reporting capability
Testing support through local and remote line and link loopbacks
E1 Network Module with 75Ω Interface
•
•
•
•
•
Four E1 circuits provided through a single DB-25, 75Ω connector
Complies with CCITT G.703, G.704, and G.823 standards (with the BNC breakout panel)
E1 circuit alarm reporting capability
Testing support through local and remote line and link loopbacks
75Ω E1 breakout panel (P/N 1280060L1) provides BNC interfaces for E1 connections
T1 Network Module
•
•
•
•
Four T1 circuits provided through four RJ-45 connectors
Complies with ANSI T1.403 and AT&T 54016 and 62411
T1 circuit alarm reporting capability
Testing support through local and remote line and link loopbacks
Quad Ethernet Switch Module
•
•
•
•
Four 10/100BaseT/TX interfaces provided through four RJ-45 connectors
Auto MDI/MDIX crossover on all interfaces
Back-pressure flow control on all half-duplex interfaces
Pause-frame flow control on all full-duplex interfaces
612806420L1-1D
Copyright © 2005 ADTRAN, Inc.
13
Section 1 System Description
14
TRACER 6000 Series Integrated System Manual
Copyright © 2005 ADTRAN, Inc.
612806420L1-1D
MICROWAVE PATH ENGINEERING BASICS
Explains the basics of analyzing a wireless microwave link or path. Defines significant parameters and
makes several installation recommendations.
CONTENTS
Line-of-Sight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Decibels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Calculating the Fade Margin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Receiver Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Antenna Gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Transmitted Power (PT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Carrier Wavelength (l) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Path Distance (d) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
System Losses (L) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Path Loss (LP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Receiver Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Antenna Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Antenna Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
TRACER RSSI Test Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Real-time Signal Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Antenna Beam Patterns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Fresnel Zones, Earth Curvature, and Antenna Heights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Other Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Path Availability. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
FIGURES
Figure 1.
Figure 2.
Example Microwave Path with Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Typical Antenna Beam Pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
TABLES
Table 1.
Table 2.
Table 3.
Table 4.
Table 5.
Table 6.
Table 7.
Table 8.
Table 9.
Table 10.
Table 11.
Antenna Gain for Given Dish Diameters with k = 0.55 (Standard) . . . . . . . . . . . . . . . . . 19
Antenna Gain for Given Dish Diameters with k = 0.55 (Metric) . . . . . . . . . . . . . . . . . . . 19
Antenna Gain for Given Dish Diameters with k = 0.40 (Standard) . . . . . . . . . . . . . . . . . 19
Antenna Gain for Given Dish Diameters with k = 0.40 (Metric) . . . . . . . . . . . . . . . . . . . 19
Transmit Power Reduction for Various Antennae Gains . . . . . . . . . . . . . . . . . . . . . . . . . 20
Typical Coaxial Loss for Common Cable Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Path Loss for Given Path Lengths (miles) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Path Loss for Given Path Lengths (kilometers) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Receiver Sensitivity for the TRACER 64x0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Minimum Antenna Height for Given Path Lengths (miles and ft) . . . . . . . . . . . . . . . . . . 26
Minimum Antenna Height for Given Path Lengths (km and m) . . . . . . . . . . . . . . . . . . . . 27
612806420L1-1D
Copyright © 2005 ADTRAN, Inc.
15
Section 2 Microwave Path Engineering Basics
1.
TRACER 6000 Series Integrated System Manual
LINE-OF-SIGHT
The TRACER 6410 and TRACER 6420 systems are designed for operation in the license-free 2.400 to
2.483 GHz and 5.725 GHz to 5.850 GHz industrial, scientific, and medical (ISM) bands, respectively.
Radio wave propagation in these bands exhibits microwave characteristics which are ideally suited for
point-to-point, line-of-sight communications. Line-of-sight requires that the transmitting antenna and
receiving antenna are able to “see” each other, and that the straight-line path between the two antennas is
free of obstructions such as buildings, trees, mountains, and in longer paths, even the curvature of the
earth. For maximum signal strength, the area around the visual line-of-sight where microwave signals
reflect (Fresnel zone) must also be free of obstructions. Fresnel zones are discussed in more detail on
page 25.
Terminology
2.
Point-to-Point
Wireless communication from a single site to another individual
site. Contrast with point-to-multipoint.
Line-of-Sight
An unobstructed, direct path exists between the transmitting and
the receiving antennas.
DECIBELS
Understanding the decibel (dB) format is key when discussing microwave path engineering because the
received signal power is often expressed in decibel format. In general, any quantity can be expressed in
decibels. If the quantity x is a power level (in watts), the decibel equivalent is defined as
x dB = 10 ⋅ log 10 ( x )
(dB)
If the quantity x is referenced to a milliwatt (mW), then the decibel-milliwatt (dBm) is used instead of a
generic decibel.
x dBm = 10 ⋅ log 10 ⎛ -------------⎞
⎝ 1mW⎠
(dBm)
Using the decibel format simplifies power calculations by reducing multiplication and division operations
into addition and subtraction operations.
3.
CALCULATING THE FADE MARGIN
It is imperative to determine whether the proposed microwave path is suitable (at a
minimum) for ideal, nondistorted signals before attempting installation.
The fade margin (F ) is a value in decibels (dB) that represents the amount of signal reduction that can be
tolerated before the link exceeds the specified bit error rate (BER). Fade margin is simply the difference
between the available signal power at the receiver (PR ) and the receiver sensitivity (Psens ).
F = P R – P sens = PT + GT + GR - L - LP - Psens
16
Copyright © 2005 ADTRAN, Inc.
(dB)
612806420L1-1D
TRACER 6000 Series Integrated System Manual
Section 2 Microwave Path Engineering Basics
where the variables in the equations are defined as
PR
Psens
PT
GT
GR
LP
received power (dBm)
receiver sensitivity (dBm)
transmitted power (adjustable up to 20 dBm maximum)
transmit antenna gain (decibels referenced to an isotropic source – dBi)
receive antenna gain (dBi)
other losses (RF coaxial cable, etc. – dB)
path loss (dB)
Higher levels of fade margin indicate stronger protection against signal fading and a more reliable link. For
most applications, 20 to 30 dB of fade margin should ensure a reliable link.
The following sections further discuss the necessary power calculations and their components.
4.
RECEIVER POWER
The viability of a particular microwave path is determined by the power of the transmitted microwave
signal, the transmit and receive antenna gain, distance, and accumulated system losses (such as RF coaxial
cable losses and path loss).
The equation relating received signal power to the other microwave parameters is
PT GT GR λ
P R = -----------------------------( 4π )2d2L
(watts, W)
or (in decibel notation)
PR = PT + GT + GR - L - LP
(decibels referenced to a milliwatt, dBm)
where the variables in the equations are defined as
PR
PT
GT
GR
λ
LP
received power (dBm)
transmitted power (adjustable up to 20 dBm maximum)
transmit antenna gain (decibels referenced to an isotropic source – dBi)
receive antenna gain (dBi)
carrier wavelength (meters)
path distance (meters)
other losses (RF coaxial cable, etc. – dB)
path loss (dB)
When using decibel notation, all quantities must be individually converted to decibels
prior to performing addition and subtraction.
612806420L1-1D
Copyright © 2005 ADTRAN, Inc.
17
Section 2 Microwave Path Engineering Basics
TRACER 6000 Series Integrated System Manual
Figure 1 illustrates a wireless link configuration containing all the parameters necessary for the power
budget analysis.
λ
GT
GR
d, LP
PT
PR
Figure 1. Example Microwave Path with Parameters
The following sections further discuss the power budget analysis and its components.
Antenna Gain
Actual transmit and receive antenna gain values depend strictly upon the physical characteristics of the
antennas installed for each link. In other words, the size of the dish determines the antenna gain. Using a
parabolic dish antenna results in the best performance. Antenna gains are specified in terms of decibels of
gain referenced to an isotropic source (dBi). An isotropic source is a hypothetical antenna having equal
radiation in all directions. The equation for calculating gain over isotropic radiation is
⎛
π ⋅ D 2⎞
10 ⋅ log ⎜ k ⋅ ⎛⎝ ------------⎞⎠ ⎟
λ
⎝
⎠
(dBi)
where
λ
dish efficiency factor (usually 0.55)
carrier wavelength (c / f)
dish diameter
The carrier wavelength (λ) and dish diameter (D) can be metric or standard units of
measure. Use the same unit of measure for both variables. For example, a carrier
wavelength of 0.124 meters requires a dish diameter in meters as well.
The dish efficiency factor (k) is used to estimate how efficiently the dish reflector passes energy to the
feedhorn. The “standard” factor is 0.55 (measured performance of prime-focus dishes with a pyrimidal
waveguide feedhorn with no aperture blockage). Other dishes and feedhorn designs may have better or
worse efficiency. Table 1 on page 19 (standard) and Table 2 on page 19 (metric) provide gains using a 0.55
dish efficiency factor. Table 3 on page 19 (standard) and Table 4 on page 19 (metric) provide gains using a
0.40 dish efficiency factor. Dish manufacturers can provide gains for specific types of antennas.
18
Copyright © 2005 ADTRAN, Inc.
612806420L1-1D
TRACER 6000 Series Integrated System Manual
Section 2 Microwave Path Engineering Basics
Table 1. Antenna Gain for Given Dish Diameters with k = 0.55 (Standard)
Dish Diameter
(in feet)
Gain at 2.4 GHz
(in dBi)
Gain at 5.8 GHz
(in dBi)
21.1
28.8
27.2
34.8
31.7
38.3
33.2
40.8
10
35.2
42.7
12
36.7
44.3
Table 2. Antenna Gain for Given Dish Diameters with k = 0.55 (Metric)
Dish Diameter
(in meters)
Gain at 2.4 GHz
(in dBi)
Gain at 5.8 GHz
(in dBi)
0.6
21.0
28.6
0.8
23.5
31.1
1.0
25.5
33.1
1.2
27.1
34.7
1.5
28.9
36.6
1.8
30.6
38.2
2.0
31.5
39.1
Table 3. Antenna Gain for Given Dish Diameters with k = 0.40 (Standard)
Dish Diameter
(in feet)
Gain at 2.4 GHz
(in dBi)
Gain at 5.8 GHz
(in dBi)
19.8
27.4
25.8
33.4
29.3
36.9
31.8
39.4
10
33.8
41.4
12
35.3
42.9
Table 4. Antenna Gain for Given Dish Diameters with k = 0.40 (Metric)
612806420L1-1D
Dish Diameter
(in meters)
Gain at 2.4 GHz
(in dBi)
Gain at 5.8 GHz
(in dBi)
0.6
19.7
27.2
0.8
22.2
29.7
1.0
24.1
31.1
1.2
25.7
33.3
1.5
27.6
35.2
1.8
29.2
36.8
2.0
30.1
37.7
Copyright © 2005 ADTRAN, Inc.
19
Section 2 Microwave Path Engineering Basics
TRACER 6000 Series Integrated System Manual
Transmitted Power (PT)
The FCC specifies the maximum transmitter power used for antennae of a given gain. FCC Rules Part 15,
Subpart 247 allow for a maximum power of 1 watt (30 dBm) into antennae of a gain less than or equal to
6 dBi. At 2.4 GHz (TRACER 6410), the 1-watt maximum transmitter power must be reduced by 1 dB for
every 3 dB of antenna gain over 6 dBi. This rule is shown in Table 5 (for information only).
Table 5. Transmit Power Reduction for Various Antennae Gains
Output Power
(dBm)
Maximum
Antenna Gain
(dBi)
Maximum EIRP
(dBm)
30
36
29
38
28
12
40
27
15
42
26
18
44
25
21
46
24
24
48
23
27
50
22
30
52
21
33
54
20
36
56
The TRACER 6410 is only approved to operate with dish antennas with a maximum gain of 21.1dBi.
For the 5.8 GHz band (TRACER 6420), the maximum output power is 1 watt (30 dBm) regardless of the gain
of the attached antenna. Since the TRACER 6420 maximum transmit power is 100 milliwatts, there is
reduction in transmitter output power required.
Carrier Wavelength (λ)
The carrier wavelength is the physical wavelength of the main RF carrier being used for communication, and
is usually approximated at the center frequency of the band (which is 2421.7 MHz for TRACER 6410 and
5787.5 MHz for the TRACER 6420). The carrier wavelength calculations follow.
λ = c / f (meters)
where
c = speed of light (in meters)
f = frequency (in Hz)
resulting in the following carrier wavelengths
TRACER 6410
λ = 3.00 x 108 / 2421.7 x 106
= 0.124 m or 12.4 cm
= 4.88 in
20
Copyright © 2005 ADTRAN, Inc.
612806420L1-1D
TRACER 6000 Series Integrated System Manual
Section 2 Microwave Path Engineering Basics
Path Distance (d)
The path distance is the physical distance between the transmit and receive antennas. For the
TRACER 64x0, these distances can range up to 30 miles (48.27 kilometers).
System Losses (L)
System losses are defined by RF coaxial cable loss, connector losses, and losses added from any additional
lightning protection devices for the power budget analysis. Coaxial cable is required to attach the TRACER
64x0 to the antenna. The length of the cable varies from a few feet to hundreds of feet, depending upon
your application and the proximity of the TRACER 64x0 to the antenna. Various grades of coaxial cable
will work sufficiently for connecting the TRACER 64x0 unit to the antenna. A low-loss coaxial cable will
minimize cable losses.
One end of the coaxial cable requires an N-type male connector (plug) to mate with the TRACER 64x0
unit. The other end of the coaxial cable requires a connector compatible with the antenna chosen for the
installation (usually an N-type male connector). Additionally, ADTRAN recommends that the outdoor
connector on the coaxial cable be weatherproofed to prevent corrosion and electrical shorting.
In areas where lightning strikes are frequent, a lightning arrestor should be installed
directly on the antenna coaxial cable. Installing lightning arrestors helps protect the
RF electronics (including the TRACER 64x0 unit) in the downstream path from
damaging voltages and currents.
Table 6 gives typical loss figures for some of the more common coaxial cable types (per 100 feet).
Table 6. Typical Coaxial Loss for Common Cable Types
Cable Type
5.8 GHz Loss/100 ft (in dB) 5.8 GHz Loss/100 ft (in dB)
RG58
80
Not recommended
RG8 (air)
20
Not recommended
RG8 (foam)
Not recommended
1/4-inch Coax
5.91
11.36
3/8-inch Coax
5.76
9.65
1/2-inch Coax
3.83
6.49
5/8-inch Coax
2.98
4.90
7/8-inch Coax
2.2
Not suitable
1 1/4-inch Coax
1.62
Not suitable
1.41
Not suitable
Not suitable
1.23
1 5/8-inch Coax
5.8 GHz Elliptical Waveguide
612806420L1-1D
Copyright © 2005 ADTRAN, Inc.
21
Section 2 Microwave Path Engineering Basics
TRACER 6000 Series Integrated System Manual
Path Loss (LP)
Path loss is the estimated attenuation between the transmit and receive antennas caused by signal
separation and scattering. The path loss is considered basic transmission loss over the microwave link. The
following expression calculates path loss:
4πd
L P = 20 ⋅ log ⎛ ----------⎞
⎝ λ ⎠
(dB)
where
λ
carrier frequency (Hz)
carrier wavelength (c / f) (meters)
path distance (meters)
speed of light, free-space (meters)
or
L P = 96.6 + 20 ⋅ log 10 ( d ) + 20·log
10
(f)
(dB)
where d is expressed in miles and f in GHz.
Path loss, as shown here, increases rapidly as either the path length increases or the carrier wavelength
decreases (which happens as the carrier frequency increases). Therefore, longer microwave paths naturally
experience more path loss than shorter paths. Likewise, higher frequency microwave communication
experiences more path loss than lower frequency microwave communication.
The path loss values for various path lengths for the TRACER 64x0 2.4 and 5.8 GHz systems are listed in
Table 7 (miles) and Table 8 on page 23 (kilometers).Values not listed in the tables can be interpolated from
those listed.
Table 7. Path Loss for Given Path Lengths (miles)
22
Path Length
(miles)
Path Loss (dB)
at 2.4 GHz
Path Loss (dB)
at 5.8 GHz
104
112
110
118
114
121
116
124
118
126
10
124
132
15
128
135
20
130
138
25
132
140
30
134
141
35
135
143
Copyright © 2005 ADTRAN, Inc.
612806420L1-1D
TRACER 6000 Series Integrated System Manual
Section 2 Microwave Path Engineering Basics
Table 8. Path Loss for Given Path Lengths (kilometers)
5.
Path Length
(kilometers)
Path Loss (dB)
at 2.4 GHz
Path Loss (dB)
at 5.8 GHz
100
108
106
114
110
117
112
120
114
122
10
120
128
15
124
131
20
126
134
25
128
136
30
130
137
35
131
139
RECEIVER SENSITIVITY
Receiver sensitivity is a value expressed in decibels referenced to one milliwatt (dBm) that corresponds to
the minimum amount of signal power needed at the receiver to achieve a given bit error rate (BER).
Receiver sensitivity is usually a negative number of decibels, and smaller receiver sensitivity (higher
quantity negative number) is better for a given BER. Several factors affect receiver sensitivity, including
the data bandwidth of the wireless link and the amount of additional signal degradation introduced in the
receiver electronics.
Receiver sensitivity of the TRACER 64x0 is dynamic as a function of the desired bandwidth; receiver
sensitivity improves as delivered bandwidth decreases. TRACER bandwidth is provided in the form of
eight channels available for mapping to the support modules. For T1 and E1 modules, each channel
mapped represents a single T1 or E1 interface. For Quad Ethernet Switch modules, each channel mapped
represents 2 Mb of Ethernet data delivered to the module. In situations where eight-channel connectivity is
not required, the delivered bandwidth can be decreased to four or two channels, and the receiver sensitivity
improves as follows:
Table 9. Receiver Sensitivity for the TRACER 64x0
Receiver Sensitivity
Delivered Bandwidth
TRACER 6410
TRACER 6420
8xT1
-86 dBm
-85 dBm
4xT1
-89 dBm
-89 dBm
2xT1
-93 dBm
-92 dBm
8xE1 or 16 Mbps Ethernet
-84 dBm
-83 dBm
4xE1 or 8 Mbps Ethernet
-87 dBm
-87 dBm
2xE1 or 4 Mbps Ethernet
-90 dBm
-90 dBm
Should an interferer be present nearby, three software-selectable band plans are provided
for frequency agility. Changing the TRACER 64x0 band plan does not require additional
components or opening of the radio. See > RF Link Configuration > RF Band Plan on
page 64 for additional details.
612806420L1-1D
Copyright © 2005 ADTRAN, Inc.
23
Section 2 Microwave Path Engineering Basics
6.
TRACER 6000 Series Integrated System Manual
ANTENNA INFORMATION
The overall wireless system is directly affected by the antenna selection and installation, discussed in the
following sections.
Verify the antenna installation meets all regulations specified in the National Electric
Code (NEC) Article 810 with particular attention to clearances from power and lighting
conductors, mounting, grounding, and antenna discharge unit.
Antenna Alignment
With line-of-sight microwave communications, optimum system performance requires that the
transmitting and receiving antennas are properly aligned. This ensures maximum received signal power at
each receiver. Antenna alignment must be achieved in both azimuth (along a horizontal plane) and
elevation (along a vertical plane). By ensuring maximum received signal strength, a received signal
strength indicator (RSSI) helps the equipment installer determine when alignment is maximized.
TRACER RSSI Test Points
RSSI for the TRACER 64x0 system is provided through the VT100 terminal menus accessed through the
RS-232 interface, and it is presented as a series of bars indicating signal strength. More bars means more
RSSI, which ensures greater received signal strength and better link performance.
If both the local and remote end of the system are operational, the remote TRACER 64x0 receive power
can be viewed from the local TRACER 64x0 VT100 terminal menu interface.
An RSSI test point located on the front panel provides a DC voltage level (relative to the GND test point)
that corresponds to the amount of signal being received from the far end’s transmitter. The voltage at this
test point can vary from approximately 0 to 5 VDC. An RSSI calibration sheet is shipped with the system
to provide the installer a cross-reference between actual received signal level (in dBm) and RSSI voltage.
This sheet is useful for verifying link budget calculations and ensuring proper equipment installation.
Real-time Signal Values
The TRACER 64x0 system displays real-time signal values for RX QUALITY, RX POWER, and TX POWER
(for both the local and remote units). RX QUALITY values are displayed as a numerical value from 0 to 100,
with 0 corresponding to poor signal quality and 100 corresponding to exceptional signal quality.
RX POWER values are displayed in dBm within ±5 dBm accuracy and can vary with extreme temperatures.
TX POWER values are displayed in dBm within ±1 dBm accuracy.
Real-time signal values are not supported on all TRACER 64x0 systems. Systems must be
ADTRAN calibrated to provide readings for Rx or Tx Power signal levels.
24
Copyright © 2005 ADTRAN, Inc.
612806420L1-1D
TRACER 6000 Series Integrated System Manual
Section 2 Microwave Path Engineering Basics
Antenna Beam Patterns
Antennas used with the TRACER 64x0 system have a particular beam shape, determined in part by the
physical construction and geometry of the antenna. The antenna beam patterns are characterized by a
dominant main lobe, which is the preferred lobe to use for point-to-point communications, and several side
lobes, as shown in Figure 2. When setting up a microwave link, antenna alignment is nothing more than
steering the main lobes of both antennas until the main lobe of one transmitter is centered on the receiving
element of the receiving antenna.
main lobe
side lobes
Figure 2. Typical Antenna Beam Pattern
Antennas are also designed to radiate RF energy efficiently for a specific range of frequencies. Please
consult the data sheet for your particular antenna make and model to ensure that it is specified to operate in
the 2400 MHz to 24835 MHz (TRACER 6410) or 5725 MHz to 5850 MHz (TRACER 6420) frequency
bands for your TRACER 64x0 system.
Fresnel Zones, Earth Curvature, and Antenna Heights
Fresnel zones correspond to regions in the microwave path where reflections of the intended signal occur
and combine in both constructive and destructive manners with the main signal, thereby either enhancing
or reducing the net power at the receiver.
In general, the odd numbered Fresnel zones (1, 3, 5, ...) add constructively at the receiver, while the even
numbered Fresnel zones (2, 4, 6, ...) add destructively at the receiver.
The first Fresnel zone corresponds to the main lobe, 60 percent of which must be free of physical
obstructions for the path calculations to be valid. Since the main lobe contains the vast majority of the
microwave energy, this zone is typically used to determine proper antenna heights when placing antennas
on towers or buildings.
The curvature of the Earth becomes a legitimate obstruction for path lengths of 7 miles (11 kilometers) or
greater, and must also be accounted for when determining minimum antenna heights.
The aggregate expression for minimum antenna height that incorporates both the 60 percent first Fresnel
zone and the Earth’s curvature is given by
h = 72.1 ----- + 0.125d
4f
612806420L1-1D
(feet)
Copyright © 2005 ADTRAN, Inc.
25
Section 2 Microwave Path Engineering Basics
TRACER 6000 Series Integrated System Manual
where f is in GHz and d is in miles or
h = 21.975 ------------- + 0.0147d
6.436 f
(meters)
where f is in GHz and d is in kilometers.
The minimum antenna heights for given path lengths are displayed in Table 10 (feet/miles) and Table 11
on page 27 (kilometers/meters).
Table 10. Minimum Antenna Height for Given Path Lengths (miles and ft)
Path Length
(miles)
10
14
16
18
20
22
24
26
28
30
32
34
36
26
Min. Antenna Height Min. Antenna Height
at 5.8 GHz
at 2.4 GHz
(ft)
(ft)
33
22
48
32
61
41
73
50
85
60
111
81
124
92
138
104
153
117
169
131
185
145
202
161
220
177
239
194
259
213
279
232
300
252
Copyright © 2005 ADTRAN, Inc.
612806420L1-1D
TRACER 6000 Series Integrated System Manual
Section 2 Microwave Path Engineering Basics
Table 11. Minimum Antenna Height for Given Path Lengths (km and m)
Path Length
(kilometers)
10
14
16
18
20
22
24
26
28
30
32
34
36
7.
Min. Antenna Height Min. Antenna Height
at 5.8 GHz
at 2.4 GHz
(meters)
(meters)
8.0
5.1
11.4
7.4
14.2
9.3
16.8
11.1
19.2
12.8
23.8
16.3
26.1
18.2
28.5
20.0
30.9
22.0
33.3
24.0
35.9
26.1
38.4
28.3
41.1
30.6
43.9
32.9
46.7
35.4
49.6
38.0
52.6
40.6
OTHER CONSIDERATIONS
Path Availability
The path availability of a wireless link is a metric that expresses the fractional amount of time a link is
available over some fixed amount of time, and depends on several factors. Path availability is expressed as
A = [ 1 – ( 2.5 × 10
–6
– F ⁄ 10
)abfd ( 10
) ] × 100%
(%)
where the parameters are
terrain factor
climate factor
carrier frequency (GHz)
path length (miles)
fade margin (dB)
or
A = [ 1 – ( 6.00 × 10
612806420L1-1D
–7
– F ⁄ 10
)abfd ( 10
) ] × 100%
Copyright © 2005 ADTRAN, Inc.
(%)
27
Section 2 Microwave Path Engineering Basics
TRACER 6000 Series Integrated System Manual
where the parameters are
terrain factor
climate factor
carrier frequency (GHz)
path length (kilometers)
fade margin (dB)
Terrain Factor (a)
The terrain factor is a quantity that compensates the link availability for different types of terrain.
Generally speaking, the smoother an area’s terrain, the less availability a wireless link running over that
terrain will have, primarily due to multipath reflections. In contrast, secondary microwave signals will be
randomly dispersed over rough terrain and will not interfere with the main signal lobe as badly as in the
smooth terrain case. The terrain factor values normally used are listed below:
Terrain
Terrain Factor
Description
Smooth
water, flat desert
Average
moderate roughness
Mountainous
1/4
very rough, mountainous
Climate Factor (b)
The climate factor is a quantity that compensates the link availability for different types of climates
(weather). In general, microwave links operating in areas with high humidity will have less availability
than those in arid areas, primarily because water is a dispersive mechanism to microwave energy and
causes the main signal lobe to refract and disperse away from the receiver location. The climate factor
values normally used are listed below:
28
Climate
Climate Factor
Description
Very Dry
1/8
desert regions
Temperate
1/4
mainland, interior region
Humid
1/2
humid and coastal regions
Copyright © 2005 ADTRAN, Inc.
612806420L1-1D
ENGINEERING GUIDELINES
Provides information to assist network designers with incorporating the TRACER 64x0 system into their
networks.
CONTENTS
Equipment Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Reviewing the Front Panel Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
RSSI Monitoring Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Front Panel LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
AUX RS232 Interface (RJ-45). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
CRAFT Port (DB-9) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Reviewing the TRACER 64x0 Rear Panel Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
MGMT 10/100BaseT/TX Connection (RJ-48C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
DC Power Connection (Plug-In Terminal Block) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Alarm Contacts (Plug-In Terminal Block) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Antenna Interface (N-Type Connector) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Network Module Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
4xT1 Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Quad Ethernet Switch Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
4xE1 Module with 120Ω Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
4xE1 Module with 75Ω Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
At-A-Glance Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
LIST OF FIGURES
Figure 1.
Figure 2.
Figure 3.
Figure 4.
TRACER 6410 Front Panel Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TRACER 6420 Front Panel Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TRACER 64x0 Rear Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
E1 Breakout Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
32
32
36
41
LIST OF TABLES
Table 1.
Table 2.
Table 3.
Table 4.
Table 5.
Table 6.
Table 7.
Table 8.
Table 9.
Table 10.
Table 11.
Table 12.
Table 13.
Table 14.
Table 15.
TRACER 64x0 Front Panel Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
TRACER 64x0 LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
AUX RS232 Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
CRAFT Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Null-Modem Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Rear Panel Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
MGMT 10/100BaseT/TX Interface Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
DC Power Connector Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Alarm Contact Connector Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
4xT1 Module RJ-45 Connector Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Quad Ethernet Switch RJ-45 Connector Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
4xE1 Module with 120Ω Interface RJ-45 Connector Pinout . . . . . . . . . . . . . . . . . . . . . . 39
4xE1 Module with 75Ω Interface DB-25 Connector Pinout . . . . . . . . . . . . . . . . . . . . . . . 40
DB-25 to 75Ω Unbalanced Cable Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
At-A-Glance Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
612806420L1-1D
Copyright © 2005 ADTRAN, Inc.
31
Section 3 Engineering Guidelines
1.
TRACER 6000 Series Integrated System Manual
EQUIPMENT DIMENSIONS
The TRACER 64x0 integrated radio is 17.2 inch (43.7 cm) W, 11.4 inch (28.9 cm) D, and
1.7 inch (4.4 cm) H, weighs 7 pounds (3.18 kg), and can be used in rackmount configurations.
2.
POWER REQUIREMENTS
The TRACER 64x0 radio has a maximum power consumption of 25 W and a maximum current draw of
1.1 A (at 21 VDC).
3.
REVIEWING THE FRONT PANEL DESIGN
The front panel contains an RSSI monitoring interface, a GND interface for reference with RSSI, a TEST
interface for factory use only, a DB-9 CRAFT PORT for management and configuration, an AUX RS232
interface (RJ-45) that provides an end-to-end serial port interface (at 9600 bps), and status LEDs to provide
visual information about the TRACER 64x0 system. Figure 1 and Figure 2 identify the various interfaces and
the LEDs for the TRACER 6410 and TRACER 6420, respectively. Table 1 on page 33 provides a brief
description of each interface.
Figure 1. TRACER 6410 Front Panel Layout
TRACER 6200
Figure 2. TRACER 6420 Front Panel Layout
32
Copyright © 2005 ADTRAN, Inc.
612806420L1-1D
TRACER 6000 Series Integrated System Manual
Section 3 Engineering Guidelines
Table 1. TRACER 64x0 Front Panel Description1
Name
Connector
Description
RSSI
bantam
DC voltage indicating strength of the received signal at
the antenna
Status LEDs
N/A
Visual status information about the system
GND
bantam
Ground reference for the RSSI interface
TEST
3.5 mm mini-jack
Factory use only
AUX RS232
RJ-45
Serial interface for a 9600 bps connection between the
local and remote systems over the RF link
CRAFT PORT
DB-9
RS-232 interface for connection to a VT100 terminal or
PC with terminal emulation software
Detailed discussions (including pinouts) of front panel components (where applicable) follow the table.
RSSI Monitoring Interface
The RSSI voltage is a function of the signal strength at the receiver and is used to measure the received
signal strength. RSSI varies from approximately 0 to 5 VDC. An RSSI calibration sheet is shipped with the
system to provide the installer a cross-reference between actual received signal level (in dBm) and RSSI
voltage. This sheet is useful for verifying link budget calculations and ensuring proper equipment
installation.
Front Panel LEDs
With the TRACER powered-on, the front panel LEDs provide visual information about the status of the
system. Table 2 describes the LEDs.
Table 2. TRACER 64x0 LEDs
For these LEDs...
This color light...
Indicates that...
PWR
Green (solid)
the TRACER is connected to a power source.
Off
the TRACER is not currently powered up.
Green (solid)
the TRACER 6410 system temperature is within normal range.
Red (solid)
the TRACER 6410 has an active temperature alarm.
Green (solid)
the TRACER 6410 system fans are working properly.
Red (solid)
the TRACER 6410 system fans are not functioning.
Amber (flashes once)
power-up self-test is in progress. If the LED continuously flashes
or remains on (solid) after 10 seconds, the unit has failed
self-test.
Green
the module is installed and functioning properly.
Red (solid)
a port on the installed module is currently in alarm.
Off
no module occupies the slot.
TEMP
*TRACER 6410 only
FAN
*TRACER 6410 only
TST
*TRACER 6420 only
STATUS
MOD1 and MOD2
612806420L1-1D
Copyright © 2005 ADTRAN, Inc.
33
Section 3 Engineering Guidelines
TRACER 6000 Series Integrated System Manual
Table 2. TRACER 64x0 LEDs (Continued)
For these LEDs...
This color light...
Indicates that...
Green (solid)
the TRACER is transmitting on Frequency Plan A.
Off
the TRACER is not transmitting on Frequency Plan A.
Green (solid)
the TRACER is transmitting on Frequency Plan B.
Off
the TRACER is not transmitting on Frequency Plan B.
RF LO
Red (solid)
the RSSI level is below suggested minimum threshold
(approximately 10 dBm above the minimum receive sensitivity).
RF DWN
Red (solid)
there is a communication problem between the local and remote
TRACERs.
PLAN A
PLAN B
AUX RS232 Interface (RJ-45)
The AUX RS232 interface provides a female RJ-45 terminal connection (wired as a DCE interface), used
for a 9600 bps point-to-point connection between the local and remote systems (over the RF link). Table 3
shows the pinout.
Table 3. AUX RS232 Pinout
34
Pin
Name
Source
Description
GND
Common
Signal ground
RTS
Attached Equipment
Request to send (unused)
TXDATA
Attached Equipment
Transmit data (from attached equipment)
DSR
TRACER
Data set ready
RXDATA
TRACER
Received data (to attached equipment)
CTS
TRACER
Clear to send
DTR
Attached Equipment
Data terminal ready (unused)
CD
TRACER
Carrier detect
Copyright © 2005 ADTRAN, Inc.
612806420L1-1D
TRACER 6000 Series Integrated System Manual
Section 3 Engineering Guidelines
CRAFT Port (DB-9)
The CRAFT connector provides a female DB-9 terminal connection (wired as a DCE interface), used for
terminal access to the TRACER system. Table 4 shows the pinout. A null modem cable is necessary for
connecting the CRAFT port to a modem for remote dial-up access. Table 5 shows the pinout for a null
modem cable.
Table 4. CRAFT Pinout
Pin
Name
CD
TRACER
Carrier detect
RXDATA
TRACER
Received data (to attached equipment)
TXDATA
Attached Equipment
Transmit data (from attached equipment)
DTR
Attached Equipment
Data terminal ready (unused)
GND
Common
Signal ground
DSR
TRACER
Data set ready
RTS
Attached Equipment
Request to send (unused)
CTS
TRACER
Clear to send
RI
TRACER
Ring indicator (unused)
Source
Description
Table 5. Null-Modem Pinout
Modem
Pin
4.
TRACER 64x0
Pin
1 (CD)
Unconnected
2 (RXD)
3 (TXD)
3 (TXD)
2 (RXD)
4 (DTR)
6 (DSR)
5 (GND)
5 (GND)
6 (DSR)
4 (DTR)
7 (RTS)
8 (CTS)
8 (CTS)
7 (RTS)
9 (RI)
Unconnected
REVIEWING THE TRACER 64X0 REAR PANEL DESIGN
Figure 3 on page 36 identifies the features of the TRACER rear panel, and Table 6 on page 36 provides a
brief description of each interface.
612806420L1-1D
Copyright © 2005 ADTRAN, Inc.
35
Section 3 Engineering Guidelines
TRACER 6000 Series Integrated System Manual
DC Power
Connection
Network
Module Slots
Antenna
Connector
Alarm
Contacts
Fuse
Ethernet
Interface
Ground
Lug
Figure 3. TRACER 64x0 Rear Panel
Table 6. Rear Panel Description1
Name
Connector
Description
Network Module
Slots
N/A
Dual network module slots for system flexibility (shown
with a single 4xT1 module and a Quad Ethernet Switch
module installed)
MGMT
RJ-45
DC Power
Terminal block
21 to 60 VDC power source connection (either polarity
referenced to ground)
Fuse
N/A
2A, 250 V, 2-inch slo-blo fuse
Alarm
Terminal block
External alarm monitoring system connection
Antenna
N-type (female)
Antenna feedline cable connection
Ground Lug
N/A
Earth ground connection
10/100BaseT/TX Ethernet interface for SNMP, TFTP, and
Telnet access
Detailed discussions (including pinouts) of rear panel components (where applicable) follow the table.
MGMT 10/100BaseT/TX Connection (RJ-48C)
The physical Ethernet interface is provided by a single RJ-48C jack (labeled MGMT) that delivers
10/100BaseT/TX for LAN connectivity. The MGMT port is used for Telnet, SNMP, and TFTP access and
is not a router interface. The MGMT port has a green LINK LED to indicate a valid link and an amber ACT
LED that flashes with data activity on the interface. Table 7 shows the pinout.
Table 7. MGMT 10/100BaseT/TX Interface Pinout
Pin
Description
TX1
Transmit positive
TX2
Transmit negative
RX1
Receive positive
4,5
7, 8
36
Name
—
RX2
—
Unused
Receive negative
Unused
Copyright © 2005 ADTRAN, Inc.
612806420L1-1D
TRACER 6000 Series Integrated System Manual
Section 3 Engineering Guidelines
DC Power Connection (Plug-In Terminal Block)
The TRACER 64x0 can operate from a supply between 21 and 60 VDC, with either polarity referenced to
ground, and consumes less than 25 W. Power supplies should be able to provide up to 25 W at the selected
voltage. Current required (in amps) is determined by dividing the power consumed (in watts) by the applied
voltage (in volts). For example, at 48 V, TRACER 64x0 would draw approximately 0.52 A
(25 W/48 V). Table 8 shows the DC power connection pinout.
Table 8. DC Power Connector Pinout
Pin
Name
Description
+/–
Voltage
GND
Ground
Fuse
The fuse holder, accessible from the rear panel of the TRACER 64x0, accepts a generic 2 A, 250 V, 2-inch
slow-blo fuse.
Alarm Contacts (Plug-In Terminal Block)
An RF link down condition is indicated with both normally open (NO) and normally closed (NC) alarm
contacts on the rear panel of the TRACER 64x0 system. In normal operation, the NC contact is electrically
connected to the common contact (COM) and the NO contact is isolated. When the RF link drops, the NC
contact becomes isolated and the NO is electrically connected to COM. This allows RF down conditions to
be reported to external alarm monitoring systems. Table 9 provides the alarm contact pinout.
Table 9. Alarm Contact Connector Pinout
Pin
Name
Description
COM
NO
Normally-Open Contact
NC
Normally-Closed Contact
Common Contact
Antenna Interface (N-Type Connector)
The ANTENNA interface (N-type connector) connects to the customer-supplied antenna using standard
antenna feedline cable. When determining the cable specifications for your application, refer to Section 2,
Microwave Path Engineering Basics (System Losses (L) on page 21) for a discussion on cable length and
loss factors.
612806420L1-1D
Copyright © 2005 ADTRAN, Inc.
37
Section 3 Engineering Guidelines
5.
TRACER 6000 Series Integrated System Manual
NETWORK MODULE INTERFACES
4xT1 Module
The 4xT1 network module has four T1 interfaces (through four RJ-45 ports) that provide the following
functions:
ANSI T1.403 and AT&T® 54016 and 62411 compliant
AMI or B8ZS coding
Extended Super Frame (ESF) and Super Frame (SF) framing support
Manual line build out
Network performance monitoring and reporting
Test loopbacks (both line and link)
•
•
•
•
•
•
Table 10 provides the RJ-45 interface pinout for the 4xT1 network module.
Table 10. 4xT1 Module RJ-45 Connector Pinout
Pin
Name
Description
Transmit data (ring) towards the network
Transmit data (tip) towards the network
3, 6-8
UNUSED
—
R1
Receive data (ring) toward the network
T1
Receive data (tip) from the network
Quad Ethernet Switch Module
The Quad Ethernet Switch module has four 10/100BaseTX interfaces (through four RJ-45 ports) that
provide the following functions:
•
•
•
•
IEEE 802.3 and 802.3u compliant
Auto MDI/MDIX crossover
Back-pressure flow control on all full-duplex interfaces
Link and activity LEDs for each port
Table 11 provides the RJ-45 interface pinout for the Quad Ethernet Switch module.
Table 11. Quad Ethernet Switch RJ-45 Connector Pinout
Pin
Name
Source
Description
RX1
Attached Equipment
Receive Positive
RX2
Attached Equipment
Receive Negative
TX1
Module
Transmit Positive
4, 5
Unused
N/A
—
TX2
Module
Transmit Negative
7, 8
Unused
N/A
—
38
Copyright © 2005 ADTRAN, Inc.
612806420L1-1D
TRACER 6000 Series Integrated System Manual
Section 3 Engineering Guidelines
4xE1 Module with 120Ω Interface
The 4xE1 network module provides four E1 interfaces (through four RJ-45 connectors) that provide the
following functions:
•
•
•
•
AMI or HDB3 coding
Framed, multi-framed, and unframed framing support
Network performance monitoring and reporting
Test loopbacks (both line and link)
Table 12 provides the RJ-45 interface pinout for the 4xE1 network module.
Table 12. 4xE1 Module with 120Ω Interface RJ-45 Connector Pinout
Pin
Name
Description
TX Tip
TX Ring
Transmit signal (Ring)
Unused
—
RX Tip
Receive signal (Tip)
RX Ring
Receive signal (Ring)
6–8
Unused
—
Transmit signal (Tip)
4xE1 Module with 75Ω Interface
The 4xE1 network module provides four E1 interfaces (through a single DB-25 interface) that provide the
following functions:
•
•
•
•
AMI or HDB3 coding
Framed, multi-framed, and unframed framing support
Network performance monitoring and reporting
Test loopbacks (both line and link)
Table 13 on page 40 provides the DB-25 interface pinout for the 4xE1 network module. A separate
breakout panel is available to provide 75Ω BNC unbalanced interfaces (see Table 14 on page 40 for the
pinout of the 75Ω cable). Figure 4 displays the E1 breakout panel.
612806420L1-1D
Copyright © 2005 ADTRAN, Inc.
39
Section 3 Engineering Guidelines
TRACER 6000 Series Integrated System Manual
Table 13. 4xE1 Module with 75Ω Interface DB-25 Connector Pinout
Pin
Name
Description
E1D RX
Receive signal for E1 D interface
E1D TX
Output signal for E1 D interface
GND
E1C RX
Receive signal for E1 C interface
E1C TX
Output signal for E1 C interface
GND
E1B RX
Receive signal for E1 B interface
E1B TX
Output signal for E1 B interface
GND
10
E1A RX
Receive signal for E1 A interface
11
E1A TX
Output signal for E1 A interface
12-25
GND
Ground
Ground
Ground
Ground
Table 14. DB-25 to 75Ω Unbalanced Cable Pinout
E1 Cable Interface
DB-25 Male
(TRACER Side)
DB-25 Male
(Breakout Panel)
Channel 1 Input
10
14
Channel 1 Output
11
Channel 2 Input
17
Channel 2 Output
Channel 3 Input
20
Channel 3 Output
Channel 4 Input
23
Channel 4 Output
12
Ground
All other pins
All other pins
40
Copyright © 2005 ADTRAN, Inc.
612806420L1-1D
TRACER 6000 Series Integrated System Manual
Section 3 Engineering Guidelines
Figure 4. E1 Breakout Panel
6.
AT-A-GLANCE SPECIFICATIONS
Table 15 on page 41 contains a list of specifications for the TRACER 64x0 system.
Table 15. At-A-Glance Specifications
Hardware
Description
Specification
Transmitter
Output Power
+27 dBm, maximum (TRACER 6410)
+20 dBm, maximum (TRACER 6420)
Frequency Range
2400 to 2483.5 MHz (TRACER 6410)
5725 to 5850 MHz (TRACER 6420)
Receive Level,
Minimum
TRACER 6410
-86 dBm @ 8xT1
-89 dBm @ 4xT1
-93 dBm @ 2xT1
-84 dBm @ 8xE1/16Mbps Ethernet
-87 dBm @ 4xE1/8 Mbps Ethernet
-90 dBm @ 2xE1/4 Mbps Ethernet
TRACER 6420
-85 dBm @ 8xT1
-89 dBm @ 4xT1
-92 dBm @ 2xT1
-83 dBm @ 8xE1/16Mbps Ethernet
-87 dBm @ 4xE1/8 Mbps Ethernet
-90 dBm @ 2xE1/4 Mbps Ethernet
Receiver
612806420L1-1D
Receive Level, Maximum
-30 dBm
Receive Level, Nominal
-55 dBm
Copyright © 2005 ADTRAN, Inc.
41
Section 3 Engineering Guidelines
TRACER 6000 Series Integrated System Manual
Table 15. At-A-Glance Specifications (Continued)
Hardware
Description
Specification
Frequency Plan
Channel Plan
Tx 2.419 GHz, Rx 2.459 GHz (TRACER 6410)
Tx 5.744 GHz, Rx 5.824 GHz (TRACER 6420)
Tx 2.422 GHz, Rx 2.462 GHz (TRACER 6410)
Tx 5.747 GHz, Rx 5.827 GHz (TRACER 6420)
Tx 2.425 GHz, Rx 2.465 GHz (TRACER 6410)
Tx 5.751 GHz, Rx 5.831 GHz (TRACER 6420)
Plan A
Channel Plan
Tx 2.459 GHz, Rx 2.419 GHz (TRACER 6410)
Tx 5.824 GHz, Rx 5.744 GHz (TRACER 6420)
Tx 2.462 GHz, Rx 2.422 GHz (TRACER 6410)
Tx 5.827 GHz, Rx 5.747 GHz (TRACER 6420)
Tx 2.465 GHz, Rx 2.425 GHz (TRACER 6410)
Tx 5.831 GHz, Rx 5.751 GHz (TRACER 6420)
Plan B
Data Encryption
Encryption Type
Symmetric Triple-DES (3DES)
Panel
Alarm LEDs
Diagnostics
RF link diagnostics and error history, transmit and receive packets
history, real-time signal levels
Test Points
RSSI and Ground (GND)
Alarms
Normally Open (NO) and Normally Closed (NC)
VT100 Terminal
Menu-driven user interface, control of the remote end, event history
Telnet Access
Menu-driven user interface, control of the remote end, event history
SNMP
Standard MIB support (T1/E1 and Ether-like MIBs); Enterprise MIB
support (ADTRAN TRACER)
User Interface
VT100 Terminal Interface
42
Data Rate
9600, 19200, 38400, 57600, 115200 bps
Data Bits
Parity
None
Stop Bits
Terminal Emulation
VT100
Copyright © 2005 ADTRAN, Inc.
612806420L1-1D
TRACER 6000 Series Integrated System Manual
Section 3 Engineering Guidelines
Table 15. At-A-Glance Specifications (Continued)
Hardware
Description
Specification
Mechanical and Environmental
Operating Temperature
-25°C to 65°C
Size
1.7 inch (4.4 cm) H
17.2 inch (43.7 cm) W
11.4 inch (28.9 cm) D
Humidity
95 percent, noncondensing
Weight
7 lbs (3.18 kg)
Input Voltage
21 to 60 VDC, either polarity referenced to ground
Power Consumption
< 25 W
Connector
2-pin terminal block (DC)
Fuse
2 A, 250 V slow-blo fuse (2-inch)
Power
Network Modules
Quad T1 Module Connection
Quad Ethernet
Switch Module
Capacity
4xT1 (ANSI T1.403, AT&T® 54016 and 62411)
Line Code
B8ZS (default), AMI
Alarms
AIS, Red, Yellow, BPVs, LOS
Connection
Four RJ-45 interfaces
Interface Type
Four 10BaseT/100BaseTX interfaces with auto MDI/MIDX
crossover
Flow Control
Back-pressure flow control on half-duplex interfaces
Pause-frame flow control on full-duplex interfaces
Quad E1 Module Connection
(120Ω Interface)
Four RJ-45 interfaces
Capacity
4xE1 (CCITT G.703)
Line Code
HDB3 (default), AMI
Alarms
LOS, LCV, AIS, RMT, OOF, CRC
Loopbacks
Local and remote line and link
Quad E1 Module Connection
(75Ω Interface)
612806420L1-1D
Four RJ-45 interfaces
Single DB-25 connector on module; 75Ω unbalanced interface
available using BNC breakout panel
Capacity
4xE1 (CCITT G.703)
Line Code
HDB3 (default), AMI
Alarms
LOS, LCV, AIS, RMT, OOF, CRC
Loopbacks
Local and remote line and link
Copyright © 2005 ADTRAN, Inc.
43
Section 3 Engineering Guidelines
44
TRACER 6000 Series Integrated System Manual
Copyright © 2005 ADTRAN, Inc.
612806420L1-1D
NETWORK TURNUP PROCEDURE
Provides shipment contents list, grounding instructions, mounting options, and specifics of supplying
power to the unit.
CONTENTS
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Unpack and Inspect the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Contents of Shipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Customer Provides . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Channel Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Grounding Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Supplying Power to the Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Mounting Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Installing Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Instructions for Installing Network Modules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Connecting the Module Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Quad T1 Module Interfaces. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Quad Ethernet Switch Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Quad E1 (120Ω) Module Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Quad E1 (75Ω) Module Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
FIGURES
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
2.4 GHz Bandwidth Division. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.8 GHz Bandwidth Division. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19-inch Rackmount Illustration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
23-inch Rackmount Illustration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TRACER 64x0 Network Module Slot Designation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
E1 Connection with Breakout Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
612806420L1-1D
Copyright © 2005 ADTRAN, Inc.
48
48
50
51
51
53
45
Section 4 Network Turnup Procedure
1.
TRACER 6000 Series Integrated System Manual
INTRODUCTION
This section discusses TRACER 64x0 system installation.
Changes or modifications not expressly approved by ADTRAN could void the user’s
authority to operate the equipment.
2.
TOOLS REQUIRED
The tools required for TRACER 64x0 installation are:
•
•
VT100 terminal or PC with terminal emulation software
RS-232 (DB-9 male for TRACER 64x0) cable for connecting to terminal
To prevent electrical shock, do not install equipment in a wet location or during a lightning
storm.
3.
UNPACK AND INSPECT THE SYSTEM
This system MUST be installed by qualified service personnel in a Restricted Access
Location.
Each TRACER 64x0 is shipped in its own cardboard shipping carton. Open each carton carefully and
avoid deep penetration into the carton with sharp objects.
After unpacking the unit, inspect it for possible shipping damage. If the equipment has been damaged in
transit, immediately file a claim with the carrier; then contact ADTRAN Customer Service (see Warranty,
Customer Service, Product Support Information, and Training information in the front of this manual).
Contents of Shipment
Your shipment of the base unit includes the following items:
•
•
•
•
•
•
TRACER 64x0 unit
RJ-45 to DB-9 connector (ADTRAN P/N 3196ADPT001) for connection to the AUX RS232 port
6-foot silver satin cable for connection to the AUX RS232 port
Rackmount brackets
Power and Alarm connectors
TRACER 64x0 Documentation CD
Your Quad T1 module shipment includes the following items:
•
•
46
Quad T1 module
Quad T1 module quick start guide
Copyright © 2005 ADTRAN, Inc.
612806420L1-1D
TRACER 6000 Series Integrated System Manual
Section 4 Network Turnup Procedure
Your Quad Ethernet Switch module shipment includes the following items:
•
•
Quad Ethernet Switch module
Quad Ethernet Switch module quick start guide
Your Quad E1 module (120Ω interface) shipment includes the following items:
•
•
Quad E1 module
Quad E1 module quick start guide
Your Quad E1 module (75Ω interface) shipment includes the following items:
•
•
•
Quad E1 module
Quad E1 module quick start guide
DB-25 to DB-25 cable for connecting to the 75Ω BNC breakout panel
Your Octal 75Ω E1 Breakout Panel shipment includes the following items:
•
•
•
Octal 75Ω E1 Breakout Panel
23-inch rack mounting brackets (ADTN P/N 3265622@A)
Octal 75Ω E1 Breakout Panel quick start guide
Customer Provides
Base System
The following items are necessary to install the TRACER 64x0 system and are not provided:
•
•
•
21 to 60 VDC power source with either polarity referenced to ground
DB-9 cable for VT100 access
Ethernet cable (for Telnet, SNMP, or TFTP access)
Quad T1 Module
•
T1 cables for connecting external equipment to the T1 interfaces (Quad T1 module only)
Quad Ethernet Switch Module
•
Ethernet cables for connected external equipment for the switch interfaces (Quad Ethernet Switch
module only)
Quad E1 (120Ω)Module
•
E1 cables for connecting the Quad E1 module to external E1 devices
Quad E1 (75Ω)Module
•
BNC cables for connecting the 75Ω E1 Breakout Panel to external devices
612806420L1-1D
Copyright © 2005 ADTRAN, Inc.
47
Section 4 Network Turnup Procedure
4.
TRACER 6000 Series Integrated System Manual
CHANNEL SELECTION
The FCC has allocated 83.5 MHz of spectrum in the 2.4 GHz band where the TRACER 6410 operates, and
125 MHz of spectrum in the 5.8 GHz band where the TRACER 6420 operates. Figure 1 and Figure 2
illustrates the bandwidth division.
Channel A
2400 MHz
2419
2422
Bandplan 1
Channel B
2425
2441.75
2459
2462
Bandplan 1
Bandplan 3
2465
2483.5 MHz
Bandplan 3
Bandplan 2
Bandplan 2
Figure 1. 2.4 GHz Bandwidth Division
Frequency Plan A
5725 MHz
Frequency Plan B
Band plan 1
Band plan 2
Band plan 3
5744
5747
5751
5787
Band plan 1
Band plan 2
Band plan 3
5824
5827
5831
5850 MHz
Figure 2. 5.8 GHz Bandwidth Division
To designate the utilization of the Industrial, Scientific, and Medical (ISM) bandwidth, there are two
different frequency plans, labeled A and B. The letter of each frequency plan setting is preset by the factory
and refers to the physical configuration of the diplexer filter inside the chassis. Each frequency plan is then
divided into three band plans (1, 2, or 3). The band plans must be the same for the local and remote
TRACER 64x0. For example, the transmitter at one end of the link will transmit in band plan 1 of frequency
plan A (the lower portion of the spectrum) and receive in band plan 1 of frequency plan B (the upper
portion). Consequently, the receiver at the other end should receive in band plan 1 of frequency plan A (the
lower portion) and transmit in band plan 1 of frequency plan B (the upper portion).
The letter of the frequency plan (A or B) must be different on both ends, and the number of the band plan (1,
2, or 3) must be the same on both ends. The default band plan configuration for the TRACER 64x0 is band
plan 1.
The frequency plan (A or B) of the unit may be changed in the field, if necessary, by rewiring the internal
diplexer. Contact Technical Support (see Warranty, Customer Service, Product Support Information, and
Training on page 7) for more information on this procedure.
48
Copyright © 2005 ADTRAN, Inc.
612806420L1-1D
TRACER 6000 Series Integrated System Manual
5.
Section 4 Network Turnup Procedure
GROUNDING INSTRUCTIONS
The following paragraphs provide grounding instruction information from the Underwriters’ Laboratory
UL60950 Standard for Safety of Information Technology Equipment Including Electrical Business
Equipment, with revisions dated March 15, 2002.
An equipment grounding conductor that is not smaller in size than the ungrounded branch-circuit supply
conductors is to be installed as part of the circuit that supplies the product or system. Bare, covered, or
insulated grounding conductors are acceptable. Individually covered or insulated equipment grounding
conductors shall have a continuous outer finish that is either green, or green with one or more yellow stripes.
The equipment grounding conductor is to be connected to ground at the service equipment.
The attachment-plug receptacles in the vicinity of the product or system are all to be of a grounding type, and
the equipment grounding conductors serving these receptacles are to be connected to earth ground at the
service equipment.
A supplementary equipment grounding conductor shall be installed between the product or system and
ground that is in addition to the equipment grounding conductor in the power supply cord.
The supplementary equipment grounding conductor shall not be smaller in size than the ungrounded
branch-circuit supply conductors. The supplementary equipment grounding conductor shall be connected to
the product at the terminal provided, and shall be connected to ground in a manner that will retain the ground
connection when the product is unplugged from the receptacle. The connection to ground of the
supplementary equipment grounding conductor shall be in compliance with the rules for terminating bonding
jumpers at Part K or Article 250 of the National Electrical Code, ANSI/NFPA 70. Termination of the
supplementary equipment grounding conductor is permitted to be made to building steel, to a metal electrical
raceway system, or to any grounded item that is permanently and reliably connected to the electrical service
equipment ground.
The supplemental grounding conductor shall be connected to the equipment using a number 8 ring terminal
and should be fastened to the grounding lug provided on the rear panel of the equipment. The ring terminal
should be installed using the appropriate crimping tool (AMP P/N 59250 T-EAD Crimping Tool or
equivalent).
The supplemental equipment grounding terminal is located on the rear panel of the
TRACER 64x0.
6.
SUPPLYING POWER TO THE UNIT
The TRACER 64x0 can operate from an LPS or Class 2 power source between 21 and 60 VDC and a
minimum output current rating of 1.2 A, with either polarity referenced to ground. Power supplies should be
able to provide up to 25 W at the selected voltage and be suitable for operation at a 50° C ambient
temperature. A dual pin terminal plug accepts power at the rear panel of the unit, providing a voltage (+/–)
and ground (GND) reference point.
•
•
612806420L1-1D
Power to the TRACER 64x0 DC system must be from a reliably grounded
21 to 60 VDC UL Listed Power Supply with outputs meeting LPS requirements.
A readily accessible disconnect device that is suitably approved and rated shall be
incorporated in the field wiring.
Copyright © 2005 ADTRAN, Inc.
49
Section 4 Network Turnup Procedure
7.
TRACER 6000 Series Integrated System Manual
MOUNTING OPTIONS
Install the TRACER 64x0 in a location that requires minimal antenna feedline length (the loss in this cable
directly affects overall system performance). The TRACER 64x0 is designed to be mounted in a rack. If
multiple units are installed in one location, one-half inch of spacing is recommended above and below the
unit.
The TRACER 64x0 systems are 1U high, rack-mountable units which can be installed into 19-inch (see
Figure 3) or 23-inch (see Figure 4 on page 51) equipment racks using the supplied rackmount brackets
(3265498@B). Follow these steps to mount the TRACER 64x0 into a rack:
Instructions for Rack Mounting the TRACER 64x0
1.
Position the TRACER 64x0 in a stationary equipment rack. This unit takes up 1U of
space. To allow proper grounding, scrape the paint from the rack around the
mounting holes where the TRACER 64x0 will be positioned.
2.
Have an assistant hold the unit in position as you install two mounting bolts through
the unit’s brackets and into the equipment rack using a #2 phillips-head
screwdriver.
Be careful not to compromise the stability of the equipment mounting rack when installing
this product.
ER
AC
TR
20
64
Figure 3. 19-inch Rackmount Illustration
50
Copyright © 2005 ADTRAN, Inc.
612806420L1-1D
TRACER 6000 Series Integrated System Manual
Section 4 Network Turnup Procedure
TR
AC
64
20
Figure 4. 23-inch Rackmount Illustration
8.
INSTALLING MODULES
Figure 5 shows the slot numbering designation as viewed from the rear of the TRACER 64x0. The
functionally identical option slots only accept TRACER 6000 Series modules.
MODULE 1
MODULE 2
Figure 5. TRACER 64x0 Network Module Slot Designation
Access modules are intended to be serviced by qualified service personnel only.
TRACER 64x0 modules are not hot swappable. Remove power from the system before
installing or removing the module.
Electronic modules can be damaged by static electrical discharge. Before handling
modules, put on an antistatic discharge wrist strap to prevent damage to electronic
components. Place modules in antistatic packing material when transporting or storing.
When working on modules, always place them on an approved antistatic mat that is
electrically grounded.
612806420L1-1D
Copyright © 2005 ADTRAN, Inc.
51
Section 4 Network Turnup Procedure
TRACER 6000 Series Integrated System Manual
Instructions for Installing Network Modules
Individual access modules insert in the back of the chassis. Two phillips-head screws hold the modules in
place for added security. To install network modules, follow the steps outlined below.
For proper airflow through the system to avoid elevated temperature levels, leave filler
plates on any unused slots.
Instructions for Installing Network Modules
9.
1.
Remove power from the unit.
2.
Remove the blank panel plate (if necessary).
3.
Slide the network module into the network slot until the module is firmly seated
against the front of the chassis.
4.
Secure the screws at both edges of the module.
5.
Install the optional hardware components (when necessary). For example, for
the E1 network module, an optional BNC breakout panel is available.
6.
Connect the cables to the associated device(s).
7.
Restore power to the unit.
CONNECTING THE MODULE INTERFACES
Quad T1 Module Interfaces
The physical T1 interfaces are provided using four RJ-45 ports located on the module. Straight-through T1
interface cables can be used to interface to any standard T1 DTE device (not supplied).
T1 crossover cables are needed when connecting two TRACER 64x0 T1 ports in
back-to-back operation.
Quad Ethernet Switch Module
The physical Ethernet interfaces are provided using four RJ-45 jacks. Ethernet cables are not supplied with
your shipment. Connect any standard Ethernet device to one of the switch ports located on the rear of the
unit.
Quad E1 (120Ω) Module Interfaces
The physical E1 interfaces are provided using four RJ-45 ports located on the module. Straight-through E1
interface cables can be used to interface to any standard E1 DTE device (not supplied).
E1 crossover cables are needed when connecting two TRACER 64x0 E1 ports in
back-to-back operation.
52
Copyright © 2005 ADTRAN, Inc.
612806420L1-1D
TRACER 6000 Series Integrated System Manual
Section 4 Network Turnup Procedure
Quad E1 (75Ω) Module Interfaces
The physical E1 interfaces are provided using a single DB-25 interface, an adapter cable, and a BNC
breakout panel. Connect one end of the adapter cable (labeled TO RADIO) to the module’s DB-25
connector, and then attach the other end of the cable (labeled TO PANEL) to the BNC breakout panel. The
75Ω unbalanced interfaces provided by the breakout panel are available for connection to standard E1
DTE devices (see Figure 6).
Figure 6. E1 Connection with Breakout Panel
612806420L1-1D
Copyright © 2005 ADTRAN, Inc.
53
Section 4 Network Turnup Procedure
54
TRACER 6000 Series Integrated System Manual
Copyright © 2005 ADTRAN, Inc.
612806420L1-1D
USER INTERFACE GUIDE
Provides detailed descriptions of all menu options and configuration parameters available for the
TRACER 64x0.
This section of the TRACER 6000 Series Integrated System Manual is designed for use by network
administrators and others who will configure and provision the system. It contains information about
navigating the VT100 user interface, configuration information, and menu descriptions.
CONTENTS
Navigating the Terminal Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Terminal Menu Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Navigating using the Keyboard Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Menu and System Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Password Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Menu Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
> System Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
> Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
> System Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
> RF Link Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
> RF Link Performance History (Main Screen) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
> RF Link Error History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
> RF Link Max/Min Received Power History. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
> RF Link Min/Max Received Signal Quality History. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
> Datapath Provisioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
> 4xE1 Module Configuration/Status/History (Main Screen). . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
> E1x Status/Configuration/Loopback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
> E1x Performance History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
> T1 Module Configuration/Status/History (Main Screen). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
> T1x Status/Configuration/Loopback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
> Ethernet Switch Module Configuration/Status/History (Main Screen) . . . . . . . . . . . . . . . . . . . 80
> Ethernet Switch Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
> Ethernet Switch Status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
> Management/Utilities (Main Screen) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
> Ping Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
> Firmware Upgrade Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
> RF Link Management Bridge Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
> System Alarms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
FIGURES
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Figure 7.
Figure 8.
Main Menu Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TRACER 64x0 System Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TRACER 64x0 Main Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TRACER 64x0 System Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RF Link Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4 GHz Bandwidth Division. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.8 GHz Bandwidth Division. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RF Link Performance History (Main Screen) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
612806420L1-1D
Copyright © 2005 ADTRAN, Inc.
57
59
62
63
65
66
66
67
55
Section 5 User Interface Guide
Figure 9.
Figure 10.
Figure 11.
Figure 12.
Figure 13.
Figure 14.
Figure 15.
Figure 16.
Figure 17.
Figure 18.
Figure 19.
Figure 20.
Figure 21.
Figure 22.
Figure 23.
Figure 24.
Figure 25.
Figure 26.
Figure 27.
Figure 28.
Figure 29.
Figure 30.
Figure 31.
Figure 32.
Figure 33.
Figure 34.
Figure 35.
Figure 36.
56
TRACER 6000 Series Integrated System Manual
RF Link Error History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RF Link Max/Min Received Power History. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RF Link Min/Max Received Signal Quality History. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Datapath Provisioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
E1 Module Configuration/Status/History (Main Screen). . . . . . . . . . . . . . . . . . . . . . . . .
E1x Status/Configuration/Loopback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
E1 Local Link Loopback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
E1 Remote Link Loopback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
E1 Local Line Loopback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
E1 Remote Line Loopback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
E1x Link Performance History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
T1 Module Configuration/Status/History (Main Screen). . . . . . . . . . . . . . . . . . . . . . . . .
T1x Status/Configuration/Loopback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
T1 Local Link Loopback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
T1 Remote Link Loopback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
T1 Local Line Loopback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
T1 Remote Line Loopback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
T1x Link Performance History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ethernet Switch Module Configuration/Status/History (Main Screen) . . . . . . . . . . . . . .
Ethernet Switch Module Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ethernet Switch Module Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Management/Utilities (Main Screen) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Management/SNMP Port Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ping Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Firmware Upgrade Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RF Link Management Bridge Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Active Fan Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Copyright © 2005 ADTRAN, Inc.
68
69
70
71
72
72
74
74
74
75
75
76
76
78
78
78
78
79
80
80
81
82
83
84
86
88
89
90
612806420L1-1D
TRACER 6000 Series Integrated System Manual
1.
Section 5 User Interface Guide
NAVIGATING THE TERMINAL MENU
The TRACER 64x0 menu system can be accessed with a VT100 compatible terminal that is connected to
the CRAFT PORT (located on the front of the unit) and set to 9600 bits per second (default), 8 data bits,
1 stop bit, and no parity. Flow control on the serial interface should be configured to NONE for proper
operation. Once a terminal is connected, press  until the login screen appears. The default
password for the TRACER 64x0 is password.
All TRACER 64x0 passwords are case-sensitive.
Terminal Menu Window
The TRACER 64x0 uses a series of menu pages and a single Main menu page to access its many features.
The Main menu page (see Figure 1) provides a link to all available configuration/status pages.
After connecting a VT100 terminal to the TRACER 64x0, press  or  to
redraw the current screen.
Figure 1. Main Menu Screen
612806420L1-1D
Copyright © 2005 ADTRAN, Inc.
57
Section 5 User Interface Guide
TRACER 6000 Series Integrated System Manual
Navigating using the Keyboard Keys
You can use various keystrokes to move through the terminal menu, to manage a terminal menu session,
and to configure the system.
Moving Through the Menus
To do this...
Press this key...
Activate the Login screen (upon initial connection)
Enter (twice)
Refresh the screen


Exit the menu system and return to the login screen

Close the Telnet session (or toggle the modem signalling to hang up an
attached modem)
 (twice)
Move up to select items
Up Arrow
p (Previous)
Move down to select items
Down Arrow
n (Next)
Edit a selected menu item
Enter
Spacebar
Scroll through configuration parameters for a menu item
Cancel an edit
Spacebar
Left/Right Arrows
p or n (Prev/Next)
Escape
Return to Main menu page
Back out to previous menu page
Left Arrow
Go to System Status menu page
2.
MENU AND SYSTEM CONTROL
Password Protection
The TRACER 64x0 provides password protection for the menu interface (via Terminal or Telnet access).
All TRACER 64x0 systems are shipped with a default password of password. (Passwords
are case-sensitive.)
58
Copyright © 2005 ADTRAN, Inc.
612806420L1-1D
TRACER 6000 Series Integrated System Manual
3.
Section 5 User Interface Guide
MENU DESCRIPTIONS
The remainder of this section describes the TRACER 64x0 menus and submenus.
The menu structure of the TRACER 64x0 system is depicted below as follows:
> MENU PAGE
> MENU PAGE > MENU SELECTION
> MENU PAGE > MENU SELECTION > SUB-MENU
> SYSTEM STATUS
Figure 2 shows the TRACER 64x0 System Status menu page. The status of major system components for
both sides of the RF link are displayed, but no configuration can be performed from this view.
Elapsed
Time
Module Status
Module Status
Local
TRACER
Status
Remote
TRACER
Status
Alarm Status
Alarm Status
RF Status
Frequency
Plan
Real-Time
Signal Values
Rx Quality
Frequency
Plan
Rx Quality
Rx Power
Rx Power
Tx Power
Navigation Reminders
Tx Power
Figure 2. TRACER 64x0 System Status
A. Elapsed Time
The top of the TRACER 64x0 System Status menu page displays the elapsed time the TRACER 64x0
system has been operational since the last power reset.
B. Module Status
A visual status of the current installed modules. The modules are listed in the order they are installed
(Module 1 on top and Module 2 on the bottom).
4XT1 MODULE
A visual status of current errors/alarms on the T1 interfaces (for both the local and remote
systems) is provided on the TRACER 6420 System Status menu page. The four available T1
interfaces on the module (A through D) are only displayed if the interface is mapped in the
DATAPATH PROVISIONING; a – is displayed for inactive, unmapped interfaces. The interface
displayed in reverse highlight indicates an active error or alarm condition on the specified
interface (A through D). Individual T1 status pages (accessible from the Main menu) provide
detailed T1 information.
612806420L1-1D
Copyright © 2005 ADTRAN, Inc.
59
Section 5 User Interface Guide
TRACER 6000 Series Integrated System Manual
QUAD ETHERNET SWITCH MODULE
A visual status of current errors/alarms on the Ethernet interfaces (for both the local and
remote systems) is provided on the TRACER 6420 System Status menu page. The
configured data rate (on the Datapath Provisioning page) is displayed. Individual status
notations for the available Ethernet interfaces are available through the Quad Ethernet
Switch Module Status page.
4XE1 MODULES
A visual status of current errors/alarms on the E1 interfaces (for both the local and remote
systems) is provided on the System Status menu page. The four available E1 interfaces on
the module (A through D) are only displayed if the interface is mapped in the DATAPATH
PROVISIONING; a – is displayed for inactive, unmapped interfaces. The interface displayed in
reverse highlight indicates an active error or alarm condition on the specified interface (A
through D). Individual E1 status pages (accessible from the Main menu) provide detailed E1
information.
C. RF Status
A graphical indicator of the RF links is located beneath the Elapsed Time display. The status of the
received radio link is indicated as RF UP or RF DOWN for each direction. This RF status display
corresponds to the RF DWN LED on the front of the unit.
D. Remote System Status
The right portion of the TRACER 64x0 System Status menu page reports the status of the remote
TRACER 64x0 (the system across the wireless link from the active terminal). If the RF link is down in
either direction, DATA NOT AVAILABLE is displayed in place of the remote system status information.
E. Local System Status
The left portion of the TRACER 64x0 System Status menu page reports the status of the local
TRACER 64x0 (the system where the active terminal is attached).
F. System Alarm Status
Indicates whether there are active system alarms (temperature, fan, or link) for the TRACER 64x0
unit. During alarm conditions, SYSTEM ALARM is displayed in reverse highlighted text. More details on
the current system alarm is found on the SYSTEM ALARMS page.
G. Frequency Plan
Displays the frequency plan (A or B) for the TRACER 64x0 unit. For an operational TRACER 64x0
system, you should have one A and one B frequency plan.
H. Rx Quality
Displays an indicator of receive signal quality that is not necessarily related to receive signal level (for
both the local and remote units) using a series of symbols (#) and a numeric value. The more symbols
(#) displayed, the better the signal quality. This indicator is related to signal-to-noise ratio and features
a colon (:) marker to indicate 10-6 bit error rate. This indicator is useful as a diagnostic tool to help
identify interference, as the system may have high receive signal level and poor signal quality in
situations where interference is an issue.
60
Copyright © 2005 ADTRAN, Inc.
612806420L1-1D
TRACER 6000 Series Integrated System Manual
Section 5 User Interface Guide
I. Rx Power
Displays the approximate receiver levels (for both the local and remote units) using a series of symbols
(#) and the actual real-time value (in dBm). The more symbols (#) displayed, the stronger the signal. If
the link is down in either direction and remote end data is unavailable, DATA NOT AVAILABLE is
displayed in place of the symbols (#).
J. Tx Power
Displays both an approximate transmitter levels (for both the local and remote units) using a series of
symbols (#) and the actual real-time value (in dBm). The more symbols (#) displayed, the stronger the
signal. If the link is down in either direction and remote end data is unavailable, DATA NOT AVAILABLE
is displayed in place of the symbols (#).
K. Navigation Reminders
Displays system navigation reminders. For more details on system navigation, refer to Navigating the
Terminal Menu on page 57.
L. Real-Time Signal Values
Displays real-time signal values for Rx Quality, Rx Power, and Tx Power (for both the local and
remote units).
Real-time signal values are not supported on all TRACER 64x0 systems. Systems must be
ADTRAN calibrated to provide readings for Rx or Tx Power signal levels.
> MAIN MENU
The TRACER 64x0 Main menu page provides access to all other configuration/status pages. Figure 3 on
page 62 shows the TRACER 64x0 Main menu page.
Installed network modules are displayed as menu options 5 (slot 1) and 6 (slot 2). Menu
options for empty slots are not displayed.
612806420L1-1D
Copyright © 2005 ADTRAN, Inc.
61
Section 5 User Interface Guide
TRACER 6000 Series Integrated System Manual
TRACER 6410
Only
Figure 3. TRACER 64x0 Main Menu
From the keyboard, use the up and down arrow keys to scroll through the available pages, or enter the
number or letter of the selected page (to highlight the menu page) and press .
Press  from any menu in the TRACER 64x0 menu structure to access the
TRACER 64x0 Main menu page.
> SYSTEM CONFIGURATION
Figure 4 on page 63 shows the TRACER 64x0 System Configuration menu page. System configuration
parameters for both the local and remote TRACER 64x0 units are available through this menu page.
62
Copyright © 2005 ADTRAN, Inc.
612806420L1-1D
TRACER 6000 Series Integrated System Manual
Section 5 User Interface Guide
Figure 4. TRACER 64x0 System Configuration
Press <1> from any menu in the TRACER 64x0 menu structure to access the System
Configuration menu page.
> SYSTEM CONFIGURATION > SITE NAME
Provides a user-defined alphanumeric description (up to 25 characters) for the TRACER 64x0 system.
> SYSTEM CONFIGURATION > SERIAL NUMBER
Displays the serial number for the unit. The serial number of the TRACER 64x0 automatically displays in
this field.
> SYSTEM CONFIGURATION > SYSTEM TIME
Displays the current time, including seconds. To edit this field, place the cursor on the field and press
. Then, enter the time in a 24-hour format (such as 23:00:00 for 11:00 p.m.). Press  when
you are finished to accept the change.
> SYSTEM CONFIGURATION > SYSTEM DATE
Displays the current date. To edit this field, place the cursor on the field and press . Then, enter the
date in mm-dd-yyyy format (for example, 10-30-1998). Press  when you are finished to accept the
change.
> SYSTEM CONFIGURATION > ELAPSED TIME
Displays the length of time the TRACER 64x0 system has been running. Each time you reset the system, this
value resets to 0 days, 0 hours, 0 min, and 0 secs.
612806420L1-1D
Copyright © 2005 ADTRAN, Inc.
63
Section 5 User Interface Guide
TRACER 6000 Series Integrated System Manual
> SYSTEM CONFIGURATION > CRAFT PORT BAUD
Specifies the baud rate of the port. Select either 9600 (default), 19200, 38400, 57600, or 115200 bps. If
you are using the CRAFT port for modem access, ensure that the CRAFT port rate matches the modem
baud rate.
> SYSTEM CONFIGURATION > INACTIVITY LOGOUT
This option defines the amount of time in minutes the user can stay connected without any activity on the
CRAFT port before the user is automatically logged out of the system. Select one of the following: 5 MIN,
10 MIN (default), 15 MIN, 30 MIN, 45 MIN, 60 MIN, or OFF.
Changes to the INACTIVITY LOGOUT setting do not apply to the current session. All changes
take affect at the next login to the system menus.
> SYSTEM CONFIGURATION > PASSWORD
Sets the password for password protection of the TRACER 64x0 terminal interface. Enter up to eight
alphanumeric characters. The system password is case sensitive.
The default password for the TRACER 64x0 is password.
> SYSTEM CONFIGURATION > PERFORMANCE STATS (CLEAR)
Resets all system error counters for the TRACER 64x0.
> SYSTEM CONFIGURATION > FACTORY DEFAULTS
Resets the system to the factory default settings. The configured IP ADDRESS, SUBNET MASK, and DEFAULT
GATEWAY are not defaulted during a factory default. When you select this command, the following
confirmation message appears:
Are you sure you want to restore factory Defaults? Y or N
Press Y to restore factory defaults or N to cancel this command.
The TOTAL ACTIVE CHANNELS parameter (on the Datapath Provisioning menu page) is
reset to the factory default value (8). Performing a factory default on any system with less
than eight active channels results in an RF link loss.
64
Copyright © 2005 ADTRAN, Inc.
612806420L1-1D
TRACER 6000 Series Integrated System Manual
Section 5 User Interface Guide
> RF LINK CONFIGURATION
Figure 5 shows the TRACER 64x0 RF Link Configuration menu page, which contains the transmit and
receive power settings and band plan configuration for both the local and remote units.
Figure 5. RF Link Configuration
> RF LINK CONFIGURATION > RX POWER
Displays the real-time receiver levels (for both the local and remote units) in dBm and a visual
approximation using a series of symbols (#). The more symbols (#) displayed, the stronger the signal.
Real-time receiver levels are displayed within ±5 dBm accuracy and can vary with extreme temperatures.
If the link is down in either direction and remote end data is unavailable, DATA NOT AVAILABLE displays in
place of the symbols (#). This parameter is display only.
> RF LINK CONFIGURATION > TX POWER
Allows the transmitter levels (for both the local and remote units) to be adjusted. The current transmitter
level is displayed in dBm or a visual approximation using a series of symbols (#). The more symbols (#)
displayed, the stronger the signal. Real-time receiver levels are displayed within ±1 dBm accuracy. If the
link is down and remote end data is unavailable, DATA NOT AVAILABLE displays in place of the symbols (#).
Pressing (+) on this field sets the TX POWER to full strength; pressing (-) reduces the TX POWER to the
minimum.
Reducing the transmitter power of the remote TRACER 64x0 could cause the RF link to
drop, requiring a technician to increase the transmit power by using the menu system at
the remote site.
612806420L1-1D
Copyright © 2005 ADTRAN, Inc.
65
Section 5 User Interface Guide
TRACER 6000 Series Integrated System Manual
> RF LINK CONFIGURATION > RF BAND PLAN
When changing RF band plans on installed links, change the remote end first. If the local
end is changed first, remote configuration capability is lost. In the event the local end is
changed first and the link is dropped, reset the local end to the previous setting to restore
the link.
Sets the band plan for the TRACER 64x0. Each frequency plan is divided into three band plans (1, 2, or 3).
Both local and remote TRACER 64x0 systems must be configured with the same band plan (1, 2, or 3) but
different frequency plans (A or B). For example, the transmitter at one end of the link will transmit in band
plan 1 of frequency plan A (the lower portion of the spectrum) and receive in band plan 1 of frequency
plan B (the upper portion). Consequently, the receiver at the other end should receive in band plan 1 of
frequency plan A (the lower portion) and transmit in band plan 1 of frequency plan B (the upper portion).
(Refer to Figure 6 (TRACER 6410) Figure 7 (TRACER 6420) for the divisions.) The TRACER 64x0
comes factory programmed with RF band plan set to Band 1.
Channel A
2400 MHz
2419
2422
Channel B
2425
Bandplan 1
2441.75
2459
2462
Bandplan 1
Bandplan 3
2465
2483.5 MHz
Bandplan 3
Figure 6. 2.4 GHz Bandwidth Division
Frequency Plan A
5725 MHz
Frequency Plan B
Band plan 1
Band plan 2
Band plan 3
5744
5747
5751
5787
Band plan 1
Band plan 2
Band plan 3
5824
5827
5831
5850 MHz
Figure 7. 5.8 GHz Bandwidth Division
66
Copyright © 2005 ADTRAN, Inc.
612806420L1-1D
TRACER 6000 Series Integrated System Manual
Section 5 User Interface Guide
> RF LINK CONFIGURATION > LINK ENCRYPTION
The TRACER 64x0 provides triple-DES (3DES) encryption of the data passed over the RF Link. When
LINK ENCRYPTION is set to ENABLED, the TRACER 64x0 sequentially applies the three keys entered in the
SUBKEY 0, 1, and 2 fields to each 64-bit block of data transmitted over the RF link. The remote
TRACER 64x0 uses the same keys to decrypt each block. (The keys entered in the local and remote
systems must be identical.)
> RF LINK CONFIGURATION > SUBKEY (0-2)
The TRACER 64x0 provides 3DES encryption of the data passed over the RF Link. When LINK
ENCRYPTION is set to ENABLED, the TRACER 64x0 sequentially applies the three keys entered in the
SUBKEY 0, 1, and 2 fields to each 64-bit block of data transmitted over the RF link. The remote
TRACER 64x0 uses the same keys to decrypt each block. (The keys entered in the local and remote
systems must be identical.) Valid entries are numbers 0 through 9 and letters a through f.
> RF LINK PERFORMANCE HISTORY (MAIN SCREEN)
Figure 8 shows the TRACER 64x0 RF Link Performance History main screen, which contains the transmit
and receive power settings and band plan configuration for both the local and remote units.
Figure 8. RF Link Performance History (Main Screen)
612806420L1-1D
Copyright © 2005 ADTRAN, Inc.
67
Section 5 User Interface Guide
TRACER 6000 Series Integrated System Manual
> RF LINK ERROR HISTORY
Figure 9 shows the TRACER 64x0 main RF Link Error History menu page, which displays detailed error
statistics for the RF link (from both the local and remote TRACER 64x0 units) in 15-minute and 24-hour
increments.
Days
24
Hours
(8 hours
displayed
at a time)
Figure 9. RF Link Error History
Link errors (LNK) represent errored seconds across the wireless link, and are generally an indication of
path or interference problems.
The link error count and minimum received signal level for the most recent 24 hours are recorded in
15-minute increments and displayed on the right side of the page. The left side of the page displays the 24
hour totals for the most recent 7 days.
Press  to view the next 8-hour segment of 15-minute totals and 

to view the previous 8-hour segment. > RF LINK MAX/MIN RECEIVED POWER HISTORY Figure 10 on page 69 shows the TRACER 64x0 RF Link Max/Min Received Power History page, which displays the available received power statistics from the system. Minimum and maximum received signal levels for the RF link (from both the local and remote TRACER 64x0 units) in 15-minute and 24-hour increments are found on this screen. 68 Copyright © 2005 ADTRAN, Inc. 612806420L1-1D TRACER 6000 Series Integrated System Manual Section 5 User Interface Guide Days 24 Hours (8 hours displayed at a time) Figure 10. RF Link Max/Min Received Power History The received power level (MIN and MAX) represents the minimum and maximum values of received signal levels in 24-hour or 15-minute increments, and is displayed as a numerical value in dBm. Real-time signal values are not supported on all TRACER 64x0 systems. Systems must be ADTRAN calibrated to provide readings for Rx or Tx Power signal levels. For uncalibrated systems, the received power level is displayed as a numerical value from 0 to 100 where 0 corresponds to 0V RSSI and 100 corresponds to 5V RSSI. The minimum receive power level is recorded to aid in troubleshooting problem RF links. Radio links with high MIN numbers and intermittent performance are probably experiencing interference, while links with low MIN numbers have improperly engineered paths or excess system losses. A system with MIN numbers varying widely could indicate fading, reflections, or an intermittent installation problem such as loose connectors, damaged coax or lightning arrestors, or water contaminated feedlines. Press to view the next 8-hour segment of 15-minute totals and

to view the previous 8-hour segment. > RF LINK MIN/MAX RECEIVED SIGNAL QUALITY HISTORY Figure 10 on page 69 shows the TRACER 64x0 RF Link Min/Max Received Signal Quality History menu page, which displays the available received signal quality statistics from the system. Minimum and maximum received signal quality levels for the RF link (from both the local and remote TRACER 64x0 units) in 15-minute and 24-hour increments are found on this menu page. 612806420L1-1D Copyright © 2005 ADTRAN, Inc. 69 Section 5 User Interface Guide TRACER 6000 Series Integrated System Manual Days 24 Hours (8 hours displayed at a time) Figure 11. RF Link Min/Max Received Signal Quality History The received power quality level (MIN and MAX) represents the minimum and maximum values of received signal quality levels in 24-hour or 15-minute increments, and is displayed as a numerical value from 0 to 100, with 0 corresponding to poor signal quality and 100 corresponding to exceptional signal quality. Radio links with consistently high MIN and MAX numbers should not experience interference. Radio links with a large difference between MIN and MAX numbers could be experiencing fading, reflections, or intermittent interference or installation problems such as loose connectors, damaged coax cable, water contaminated feedlines, or damaged lightning arrestors. Radio links with consistently low MIN and MAX numbers may be experiencing interference, low receive levels, or installation problems. If this is the case, examine the RF LINK MIN/MAX RECEIVED POWER HISTORY. High received power numbers with low received signal quality numbers indicate interference, while low received power numbers with low received signal quality numbers indicate low receive levels or installation problems. Press to view the next 8-hour segment of 15-minute totals and

to view the previous 8-hour segment. 70 Copyright © 2005 ADTRAN, Inc. 612806420L1-1D TRACER 6000 Series Integrated System Manual Section 5 User Interface Guide > DATAPATH PROVISIONING Figure 12 shows the Datapath Provisioning menu page, which displays the active network interfaces for the installed modules (from both the local and remote TRACER 64x0 units). Figure 12. Datapath Provisioning > DATAPATH PROVISIONING > TOTAL ACTIVE CHANNELS Defines the total number of channels active on the installed modules. Specify 2, 4, or 8 total active channels. After defining the total number of active channels, specify the actual active channels using the CHANNEL SELECTION menu. > DATAPATH PROVISIONING > MODULE 1/MODULE 2 CHANNELS (Read Only) Displays the total number of active channels on the installed module. The number of active channels and the channel configuration on both the local and remote systems must match for the RF link to function properly. A discrepancy between the systems can result in unpredictable operation. > DATAPATH PROVISIONING > CHANNEL SELECTION Defines the active channels (A, B, C, D) on each installed T1 module or the bandwidth dedicated to the Quad Ethernet Switch module (in 2 Mbps steps). To activate a channel, press and use the spacebar or arrow keys to cycle through the available channel combinations until the desired combination displays. Press again to make the channel combination change. If the specified channel selection is not valid, the TRACER 64x0 automatically corrects the configuration and populates the field with a valid selection. The number of active channels and the channel configuration on both the local and remote systems must match for the RF link to function properly. A discrepancy between the systems can result in unpredictable operation. 612806420L1-1D Copyright © 2005 ADTRAN, Inc. 71 Section 5 User Interface Guide TRACER 6000 Series Integrated System Manual > 4XE1 MODULE CONFIGURATION/STATUS/HISTORY (MAIN SCREEN) Figure 13 shows the TRACER 64x0 E1 Module Configuration main screen, which contains access to the status, configuration, testing, and performance history parameters for the selected E1 module. Figure 13. E1 Module Configuration/Status/History (Main Screen) > E1X STATUS/CONFIGURATION/LOOPBACK The following menus for the E1X STATUS/CONFIGURATION/LOOPBACK apply to all four available E1 interfaces (A through D). Figure 14 shows the E1x Status/Configuration/Loopback menu page, which displays a real-time graphical representation for the E1x link using data from both the local and remote TRACER 64x0 units. E1x operational configuration parameters and testing functions are configured from this menu. Figure 14. E1x Status/Configuration/Loopback 72 Copyright © 2005 ADTRAN, Inc. 612806420L1-1D TRACER 6000 Series Integrated System Manual Section 5 User Interface Guide > E1X STATUS/CONFIGURATION/LOOPBACK > E1X INTERFACE ALARMS Displays any active alarms on the E1 link (reported from both the local and remote TRACER 64x0 units). These alarms include AIS, CRC, LCV, LOS, OOF, and RMT. Table 1 briefly describes these alarms. See Section 8, Troubleshooting Guide, on page 123 for more information on these alarms. Table 1. E1 Interface Alarms AIS (Alarm Indication Signal) Activates when an incoming remote alarm is received from a connected E1 device. An AIS signal is an unframed all one signal that replaces the normal traffic signal. CRC (Loss of CRC-4 Framing) The receiver is unable to synchronize to the CRC-4 frame pattern of the received signal. LCV (Line Code Violations) Activates when the incoming E1 stream presents line coding violations. LOS (Loss of Signal) Activates when no E1 signal is present from the connected E1 equipment. LOS is activated after receiving 192 consecutive zeros. OOF (Out of Frame) The receiver is unable to synchronize to the FAS framing pattern of the received signal. RMT (Received Remote Alarm) Activates when an incoming remote alarm is received from the E1 device, indicating that a failure has occurred in the received direction. > E1X STATUS/CONFIGURATION/LOOPBACK > INTERFACE TYPE (Read Only) Displays the current interface type of the E1 module as either 75 OHM or 120 OHM. > E1X STATUS/CONFIGURATION/LOOPBACK > ALARM REPORTING Determines whether the TRACER 64x0 unit will report active alarms. If set to DISABLED, no alarms will be displayed on this menu page. The ALARM REPORTING parameter is independently configured for the local and remote TRACER 64x0 units. When set to DISABLED, the TRACER 64x0 does not report active alarms via SNMP, the CRAFT port, alarm contacts, menu screens, or LEDs on the front panel. By default, alarm reporting is set to ENABLED. > E1X STATUS/CONFIGURATION/LOOPBACK > CRC4 DETECTION When ENABLED, the receiver detects the CRC-4 checksum bits in the outgoing E1 data stream and checks the received signal for errors. > E1X STATUS/CONFIGURATION/LOOPBACK > SIGNALING Configures the framing format for the E1 link. The TRACER 64x0 transports E1 data across the link (as long as the E1 signal is properly timed). Configure the framing format (using the SIGNALING menu) to enable the TRACER 64x0 to monitor incoming framing error events and indicate problems with the attached metallic service. The TRACER 64x0 supports MULTIFRAMED (also known as CAS), UNFRAMED (all data stream with no framing sequence bits), and FRAMED (also known as CCS). The default value is FRAMED. 612806420L1-1D Copyright © 2005 ADTRAN, Inc. 73 Section 5 User Interface Guide TRACER 6000 Series Integrated System Manual > E1X STATUS/CONFIGURATION/LOOPBACK > LINE CODE Sets the line coding for the E1 link. The TRACER 64x0 supports high-density bipolar 3 substitution (HDB3) and alternate mark inversion (AMI) line coding. HDB3 coding does not allow more than three consecutive zeros in a transmitted bit stream and is the standard coding method on public networks. > E1X STATUS/CONFIGURATION/LOOPBACK > LOOP/NORMAL STATE Controls the loop status of the E1 link. Activates/deactivates loopback conditions for testing purposes. > E1X STATUS/CONFIGURATION/LOOPBACK > LOOP/NORMAL STATE > NORMAL Defines the E1 link as normal data transport mode; there are no active loopbacks. > E1X STATUS/CONFIGURATION/LOOPBACK > LOOP/NORMAL STATE > LINK [LOCAL] Activates a loopback at the local TRACER 64x0 E1 framer towards the remote end of the wireless link (see Figure 15). Use the local LINK loopback to loop the data transmitted from the remote end of the link back across the radio link to the remote end of the link. This loopback tests the integrity of the radio link and all the associated digital and RF hardware. Figure 15. E1 Local Link Loopback > E1X STATUS/CONFIGURATION/LOOPBACK > LOOP/NORMAL STATE > LINK [REMOTE] Activates a loopback at the remote TRACER 64x0 E1 framer towards the local end of the wireless link (see Figure 16). Use the remote LINK loopback to loop the data transmitted from the local end of the link across the radio link to the local end of the link. This loopback tests the integrity of the radio link and all the associated digital and RF hardware. Figure 16. E1 Remote Link Loopback > E1X STATUS/CONFIGURATION/LOOPBACK > LOOP/NORMAL STATE > LINE [LOCAL] Activates a loopback at the local TRACER 64x0 E1 framer towards the locally connected E1 equipment (see Figure 17). Use the local LINE loopback to test data path integrity from the local TRACER 64x0 unit to the connected E1 equipment. Figure 17. E1 Local Line Loopback 74 Copyright © 2005 ADTRAN, Inc. 612806420L1-1D TRACER 6000 Series Integrated System Manual Section 5 User Interface Guide > E1X STATUS/CONFIGURATION/LOOPBACK > LOOP/NORMAL STATE > LINE [REMOTE] Activates a loopback at the remote TRACER 64x0 E1 framer towards the connected E1 equipment at the remote end of the link (see Figure 18). Use the remote LINE loopback to test data path integrity from the remote TRACER 64x0 unit to the E1 equipment connected at the remote end of the link. Figure 18. E1 Remote Line Loopback > E1X PERFORMANCE HISTORY The following menus for the E1X PERFORMANCE HISTORY apply to all four available E1 interfaces (A through D). Figure 19 shows the E1x Performance History menu page, which displays detailed error statistics for the E1 link (from both the local and remote TRACER 64x0 units) in 15-minute and 24-hour increments. 24 Hours Days (8 Hours displayed at a time) Figure 19. E1x Link Performance History E1 performance data is presented as Errored Seconds (ES) and Severely Errored Seconds (SES) on the E1 interface. The following events qualify as an ES: LOS, OOF, LCV, or CRC error. An SES is caused by a loss of signal or an out-of-frame event. The error count for the most recent 24 hours are recorded in 15-minute increments and displayed on the right side of the page. The left side of the page displays the 24-hour totals for the most recent 7 days. Press to view the next 8-hour segment of 15-minute totals and

to view the previous 8-hour segment. 612806420L1-1D Copyright © 2005 ADTRAN, Inc. 75 Section 5 User Interface Guide TRACER 6000 Series Integrated System Manual > T1 MODULE CONFIGURATION/STATUS/HISTORY (MAIN SCREEN) Figure 20 shows the TRACER 64x0 4xT1 Module Configuration main screen, which contains access to the status, configuration, testing, and performance history parameters for the selected T1 module. Figure 20. T1 Module Configuration/Status/History (Main Screen) > T1X STATUS/CONFIGURATION/LOOPBACK The following menus for the T1X STATUS/CONFIGURATION/LOOPBACK apply to all four available T1 interfaces (A through D). Figure 21 shows the T1x Status/Configuration/Loopback menu page, which displays a real-time graphical representation for the T1x link using data from both the local and remote TRACER 64x0 units. T1x operational configuration parameters and testing functions are configured from this menu. Figure 21. T1x Status/Configuration/Loopback 76 Copyright © 2005 ADTRAN, Inc. 612806420L1-1D TRACER 6000 Series Integrated System Manual Section 5 User Interface Guide >T1X STATUS/CONFIGURATION/LOOPBACK > T1X INTERFACE ALARMS Displays any active alarms on the T1 link (reported from both the local and remote TRACER 64x0 units). These alarms include Red, Blue/AIS, Yellow, LOS, and bipolar violations (BPV). Table 2 briefly describes these alarms. See Section 8, Troubleshooting Guide, on page 123 for more information on these alarms. Table 2. T1 Interface Alarms RED Activates when no T1 signal is present from the connected T1 equipment. LOS is activated after receiving 192 consecutive zeros. BLUE/AIS (Alarm Indication Signal) Activates when an incoming remote alarm is received from a connected T1 device. An AIS signal is an unframed all one signal that replaces the normal traffic signal. YEL (Yellow Alarm) Activates when an incoming remote alarm is received from the T1 device indicating that a failure has occurred in the received direction. LOS (Loss of Sync) Occurs when the TRACER system cannot synchronize to the incoming T1 data stream. BPV (Bipolar Violations) Activates when the incoming T1 stream presents BPVs. BPVs occur when two one bits are received back-to-back with the same polarity. > T1X STATUS/CONFIGURATION/LOOPBACK > ALARM REPORTING Determines whether the TRACER 64x0 unit will report active alarms. If set to DISABLED, no alarms will be displayed on this menu page. The ALARM REPORTING parameter is independently configured for the local and remote TRACER 64x0 units. When set to DISABLED, the TRACER 64x0 does not report active alarms via SNMP or the CRAFT port, and the status LEDs are off. By default, alarm reporting is set to ENABLED. >T1X STATUS/CONFIGURATION/LOOPBACK > T1X LINE BUILD OUT Configures the T1 for the appropriate line build out, based on the distance to the T1 equipment. By default, the line build out for the TRACER 64x0 is 0 dB/133 FT. > T1X STATUS/CONFIGURATION/LOOPBACK > SIGNALING Configures the framing format for the T1 link for both the local and remote TRACER 64x0 units. The TRACER 64x0 transports T1 data across the link (as long as the T1 signal is properly timed). Configure the framing format (using the SIGNALING menu) to enable the TRACER 64x0 to monitor incoming framing error events and indicate problems with the attached metallic service. The TRACER 64x0 supports both extended superframe (ESF) and superframe (D4) framing formats. By default, the signaling method is set to ESF. > T1X STATUS/CONFIGURATION/LOOPBACK > LINE CODE Sets the line coding for the T1 link. The TRACER 64x0 supports bipolar eight-zero substitution (B8ZS) and alternate mark inversion (AMI) line coding. By default, the line code is set to B8ZS. > T1X STATUS/CONFIGURATION/LOOPBACK > LOOP/NORMAL STATE Controls the loop status of the T1 link. Activates/deactivates loopback conditions for testing purposes. 612806420L1-1D Copyright © 2005 ADTRAN, Inc. 77 Section 5 User Interface Guide TRACER 6000 Series Integrated System Manual > T1X STATUS/CONFIGURATION/LOOPBACK > LOOP/NORMAL STATE > NORMAL Defines the T1 link as normal data transport mode; there are no active loopbacks. > T1X STATUS/CONFIGURATION/LOOPBACK > LOOP/NORMAL STATE > LINK [LOCAL] Activates a loopback at the local TRACER 64x0 T1 framer towards the remote end of the wireless link (see Figure 22). Use the local LINK loopback to loop the data transmitted from the remote end of the link back across the radio link to the remote end of the link. This loopback tests the integrity of the radio link and all the associated digital and RF hardware. Figure 22. T1 Local Link Loopback > T1X STATUS/CONFIGURATION/LOOPBACK > LOOP/NORMAL STATE > LINK [REMOTE] Activates a loopback at the remote TRACER 64x0 T1 framer towards the local end of the wireless link (see Figure 23). Use the remote LINK loopback to loop the data transmitted from the local end of the link across the radio link to the local end of the link. This loopback tests the integrity of the radio link and all the associated digital and RF hardware. Figure 23. T1 Remote Link Loopback > T1X STATUS/CONFIGURATION/LOOPBACK > LOOP/NORMAL STATE > LINE [LOCAL] Activates a loopback at the local TRACER 64x0 T1 framer towards the connected T1 equipment (see Figure 24). Use the local LINE loopback to test data path integrity from the local TRACER 64x0 unit to the connected T1 equipment. Figure 24. T1 Local Line Loopback > T1X STATUS/CONFIGURATION/LOOPBACK > LOOP/NORMAL STATE > LINE [REMOTE] Activates a loopback at the remote TRACER 64x0 T1 framer towards the connected T1 equipment at the remote end of the link (see Figure 25). Use the remote LINE loopback to test data path integrity from the remote TRACER 64x0 unit to the T1 equipment connected at the remote end of the link. Figure 25. T1 Remote Line Loopback 78 Copyright © 2005 ADTRAN, Inc. 612806420L1-1D TRACER 6000 Series Integrated System Manual Section 5 User Interface Guide > T1X PERFORMANCE HISTORY The following menus for the T1x Performance History apply to all four available T1 interfaces (A through D). Figure 26 shows the T1x Performance History menu page, which displays detailed error statistics for the T1 link (from both the local and remote TRACER 64x0 units) in 15-minute and 24-hour increments. Days 24 Hours (8 hours displayed at a time) Figure 26. T1x Link Performance History T1 performance data is presented as Errored Seconds (ES) and Severely Errored Seconds (SES) on the T1 interface. The following events qualify as an ES: AIS, LOS or LOF alarm second, a single BPV, excessive zero event, or a single parity bit. An SES is caused by an AIS, LOS or LOF alarm second, excessive BPVs, or framed parity-bit errors causing a line bit error rate (BER) of 10-6. The error counts for the most recent 24 hours are recorded in 15-minute increments and displayed on the right side of the page. The left side of the page displays the 24-hour totals for the most recent 7 days. Press to view the next 8-hour segment of 15-minute totals and

to view the previous 8-hour segment. 612806420L1-1D Copyright © 2005 ADTRAN, Inc. 79 Section 5 User Interface Guide TRACER 6000 Series Integrated System Manual > ETHERNET SWITCH MODULE CONFIGURATION/STATUS/HISTORY (MAIN SCREEN) Figure 27 shows the Ethernet Switch Module Configuration/Status/History main screen, which contains access to the status, configuration, testing, and performance history parameters for the selected Ethernet Switch module. Figure 27. Ethernet Switch Module Configuration/Status/History (Main Screen) > ETHERNET SWITCH CONFIGURATION Figure 28 shows the Ethernet Switch Module Configuration screen, which contains access to the port configuration options for the available Ethernet interfaces on the selected module. The following menus for the ETHERNET SWITCH CONFIGURATION apply to all four available Ethernet interfaces (1 through 4). Figure 28. Ethernet Switch Module Configuration 80 Copyright © 2005 ADTRAN, Inc. 612806420L1-1D TRACER 6000 Series Integrated System Manual Section 5 User Interface Guide >ETHERNET SWITCH CONFIGURATION > PORT X The Quad Ethernet Switch module provides the capability to individually disable interfaces on the module. Selecting DISABLE from the PORT X menu disables the port, stopping all data passing through the interface. >ETHERNET SWITCH CONFIGURATION > SPEED/DUPLEX Defines the speed and duplex for the selected Ethernet interface. Available options are: 100/FDX (100 Mbps with full-duplex operation), 100/HDX (100 Mbps with half-duplex operation), 10/FDX (10 Mbps with full-duplex operation), and 10/HDX (10 Mbps with half-duplex operation), and AUTO (automatically detects speed and duplex of the connection). The speed and duplex settings of the TRACER Ethernet port and the attached Ethernet equipment should be identical; if the TRACER is set to auto-negotiation, the attached equipment should also be set for auto-negotiation.When the SPEED/DUPLEX is manually set, 802.3u auto-negotiation is disabled; the Ethernet equipment connected to the manual port must be manually set to the same speed/duplex settings. When set to AUTO, the actual negotiated speed and duplex of the system can be displayed on the Ethernet Switch Status page. > ETHERNET SWITCH STATUS Figure 29 shows the Ethernet Switch Status menu page, which displays the current speed and duplex operation for each switch interface (on both the local and remote TRACER 64x0 systems) as well as transmit and receive data statistics for the Ethernet interface (from both the local and remote TRACER 64x0 systems) and RF link. Figure 29. Ethernet Switch Module Status >ETHERNET SWITCH STATUS > TX PACKETS Displays a counter of all data packets transmitted out the local and remote TRACER 64x0 Ethernet interfaces. Use this data as an indicator for how many packets are being transmitted between the four Ethernet interfaces versus over the wireless link (WAN stats). The WAN statistics (Ethernet packets transmitted over the RF link) provide a quick way to determine Ethernet packet loss over the wireless link; the RX PACKETS on the local system should match the TX PACKETS on the remote side (and vice versa). >ETHERNET SWITCH STATUS > TX PACKETS DROPPED Displays a counter of all transmit data packets that were unable to be transmitted out the individual Ethernet interfaces (for both the local and remote TRACER 64x0 units). Use this data as an indicator of congestion on the Ethernet network segments. Dropped packets on the WAN interface can indicate that the provisioned bandwidth for the switch module is insufficient. 612806420L1-1D Copyright © 2005 ADTRAN, Inc. 81 Section 5 User Interface Guide TRACER 6000 Series Integrated System Manual >ETHERNET SWITCH STATUS > RX PACKETS Displays a counter of all data packets received on the local and remote TRACER 64x0 Ethernet interfaces and WAN (RF link). Use this data as an indicator of how many packets are being received on the four Ethernet interfaces versus being received over the wireless link. >ETHERNET SWITCH STATUS > RX PACKETS DROPPED Displays a counter of all received data packets that were unable to be processed due to congestion inside the TRACER 64x0 switch (for both the local and remote TRACER 64x0 units). Use this data as an indicator of congestion inside the TRACER 64x0 switch. >ETHERNET SWITCH STATUS > RX PACKET ERRORS Displays a counter of all received data packets that are greater than or equal to 64 bytes in length and have either an FCS error or an alignment error (for both the local and remote TRACER 64x0 units). RX PACKET ERRORS on the WAN interface (RF link) could indicate link degradation (due to interference, fading, etc.). If the RF link goes down, some packet errors may display. Once the TRACER 64x0 system recognizes the link is down (an active RF Low alarm), packet errors will NOT increment. > MANAGEMENT/UTILITIES (MAIN SCREEN) Figure 30 shows the TRACER 64x0 Management/Utilities main screen, which contains access to the SNMP configuration, firmware upgrade options, and a ping utility for Ethernet testing. Figure 30. Management/Utilities (Main Screen) 82 Copyright © 2005 ADTRAN, Inc. 612806420L1-1D TRACER 6000 Series Integrated System Manual Section 5 User Interface Guide > MANAGEMENT/SNMP PORT CONFIGURATION Figure 31 shows the Management/SNMP Port Configuration menu page, which contains the configuration parameters for the 10/100BaseT/TX MGMT Ethernet interface and SNMP configuration parameters (from both the local and remote TRACER 64x0 units). Figure 31. Management/SNMP Port Configuration > MANAGEMENT/SNMP PORT CONFIGURATION > IP ADDRESS Lists the address assigned to the 10/100BaseT/TX MGMT Ethernet port. This address is in dotted decimal notation (four decimal numbers, each in the range of 0 to 255, separated by periods). This value is set to 192.168.0.10 by default. Obtain the correct IP address from your LAN administrator. > MANAGEMENT/SNMP PORT CONFIGURATION > NET MASK Defines which part of a destination IP address contains the network number. This address is in dotted decimal notation (four decimal numbers, each in the range of 0 to 255, separated by periods). This value is set to 255.255.255.0 by default. This part of the destination IP address is used along with the TRACER 64x0 IP address to determine which nodes must be reached through the default IP gateway. > MANAGEMENT/SNMP PORT CONFIGURATION > DEFAULT GATEWAY Defines or changes the default gateway. You will need a default gateway if the LAN contains multiple segments. This address is in dotted decimal notation (four decimal numbers, each in the range of 0 to 255, separated by periods). This value is set to 192.168.0.254 by default. Contact your LAN administrator for the appropriate address. > MANAGEMENT/SNMP PORT CONFIGURATION > MAC ADDRESS (Read Only) Displays the system Ethernet Media Access Control (MAC) address. > MANAGEMENT/SNMP PORT CONFIGURATION > SNMP MANAGEMENT Controls SNMP management in the TRACER system. When set to DISABLED, the TRACER system does not send SNMP traps. When set to ENABLED, the TRACER system sends SNMP traps to configured management systems. 612806420L1-1D Copyright © 2005 ADTRAN, Inc. 83 Section 5 User Interface Guide TRACER 6000 Series Integrated System Manual > MANAGEMENT/SNMP PORT CONFIGURATION > SNMP GET COMMUNITY Defines the community name for Get access (to poll the TRACER 64x0 for status information). This value must match the Get name defined on the network management stations (NMS). Get access is read only access. The default name is public. > MANAGEMENT/SNMP PORT CONFIGURATION > SNMP PUT COMMUNITY Defines the community name for Set access (to change TRACER 64x0 configuration parameters through SNMP). This value must match the Get or Set name defined on the NMS. The default name is private. > MANAGEMENT/SNMP PORT CONFIGURATION > SNMP TRAP COMMUNITY Defines the community name for trap destinations. This name must match the community name defined on the NMS. The default name is SNMP_trap. > MANAGEMENT/SNMP PORT CONFIGURATION > SNMP TRAP HOST #0 - #4 Identifies the IP address in dotted decimal notation of the NMS for the TRACER 64x0 to send SNMP traps to. Up to five trap destinations can be entered. > PING UTILITY Figure 32 shows the Ping Utility menu page, which contains the parameters for performing a ping test out of the 10/100BaseT/TX MGMT Ethernet interface. Figure 32. Ping Utility > PING UTILITY > PING ADDRESS Specifies the IP address to ping (in dotted decimal notation). 84 Copyright © 2005 ADTRAN, Inc. 612806420L1-1D TRACER 6000 Series Integrated System Manual Section 5 User Interface Guide > PING UTILITY > NUMBER OF PACKETS Specifies the number of ping packets to send to the IP address specified in the PING ADDRESS field. The default value is 4, and the maximum value is 99. > PING UTILITY > PACKET SIZE (BYTES) Specifies the size (in bytes) of the data portion of the ping request. The default value is 64 bytes, and the maximum size is 1472 bytes. > PING UTILITY > TIMEOUT (MS) Specifies the time (in milliseconds) to wait for a ping reply before timing out. The default timeout is 3 seconds (3000 milliseconds), and the maximum value is 10 seconds (10000 milliseconds). > PING UTILITY > PING COMMAND Use this field to manually start (START) or stop (ABORT) a ping request, reset the ping statistics (RESET STATS), or return the ping configuration parameters to their default values (DEFAULT VALUES). > PING UTILITY > DELAY (Read Only) Displays the round trip time (in milliseconds) of the ping request/reply of the current set of pings and provides the following information: MINIMUM The minimum round trip time of the ping request/reply for the current set of pings. MAXIMUM The maximum round trip time of the ping request/reply for the current set of pings. AVERAGE The average round trip time of the ping request/reply for the current set of pings. >PING UTILITY > PACKETS (Read Only) Displays the packet statistics for the ping request/reply of the current set of pings and provides the following information: TX The number of ping requests transmitted. RX The number of ping replies received. LOST The number of ping requests that did not receive replies. 612806420L1-1D Copyright © 2005 ADTRAN, Inc. 85 Section 5 User Interface Guide TRACER 6000 Series Integrated System Manual > FIRMWARE UPGRADE UTILITY Figure 33 shows the Firmware Upgrade Utility menu page, which contains the parameters for performing a firmware upgrade for the local and remote systems. Figure 33. Firmware Upgrade Utility > FIRMWARE UPGRADE UTILITY > FILE XFER METHOD Lists the available transfer methods for updating the TRACER 64x0 system. The following selections are available: TFTP LOCAL MGMT PORT Upgrade the firmware using a trivial file transfer protocol (TFTP) server that is located on the same Ethernet network as the local system. TFTP transfers files by specifying an appropriate server address and filename. TFTP REMOTE MGMT PORT Upgrade the firmware using a TFTP server that is located on the same Ethernet network as the remote system. TFTP transfers files by specifying an appropriate server address and filename. XMODEM Upgrade the firmware using XMODEM software on a terminal or PC that is connected to the CRAFT interface of the local system. > FIRMWARE UPGRADE UTILITY > TFTP SERVER (Available for TFTP transfers only.) Configures the IP address of the TFTP server on which the update file resides. The TRACER 64x0 uses this field to locate the network TFTP server and request the file transfer. > FIRMWARE UPGRADE UTILITY > TFTP FILENAME (Available for TFTP transfers only.) Specifies the name of the update file to retrieve from the TFTP server. Enter the full filename for the file. Some TFTP servers require the full path name for any file not located in the default directory. Refer to the TFTP software documentation for more details. 86 Copyright © 2005 ADTRAN, Inc. 612806420L1-1D TRACER 6000 Series Integrated System Manual Section 5 User Interface Guide > FIRMWARE UPGRADE UTILITY > UPGRADE DESTINATION Specify the unit to upgrade. The following options are available: LOCAL IDU Upgrade the local system. REMOTE IDU Upgrade the remote system. When upgrading the remote system, the upgrade file is first loaded into the local system and then transferred over the wireless link to the remote system. The actual upgrade process is not started on the remote system until the entire upgrade file has been received. > FIRMWARE UPGRADE UTILITY > COMMAND Use this command to start (START) or stop (ABORT) a firmware upgrade. For XMODEM updates, cancel the process via the terminal emulation software (consult your documentation for instructions on how to do this). For TFTP updates, you can cancel the process by selecting ABORT from this field. > FIRMWARE UPGRADE UTILITY > LOCAL CURRENT STATUS (Available for TFTP updates only.) Indicates progress or problems encountered during the current upgrade of the local unit. The field displays IDLE if no update is in progress or when the update is successfully completed. At the end of a successful update, the contents of this field are copied into the Local Previous Status. For a detailed listing of these messages, please refer to DLP-5, Updating the Firmware Using TFTP, on page 103. > FIRMWARE UPGRADE UTILITY > LOCAL PREVIOUS STATUS (Available for TFTP updates only.) Displays the status of the previous update of the local unit. Following a successful update, this field reads UPGRADE FINISHED SUCCESSFULLY. If an update was unsuccessful, the appropriate error message displays. Refer to DLP-5, Updating the Firmware Using TFTP, on page 103 for more details on available error messages. > FIRMWARE UPGRADE UTILITY > REMOTE CURRENT STATUS (Available for TFTP updates only.) Indicates progress or problems encountered during the current upgrade of the remote unit. The field displays IDLE if no update is in progress or when the update is successfully completed. At the end of a successful update, the contents of this field are copied into the Local Previous Status. For a detailed listing of these messages, please refer to DLP-5, Updating the Firmware Using TFTP, on page 103. > FIRMWARE UPGRADE UTILITY > REMOTE PREVIOUS STATUS (Available for TFTP updates only.) Displays the status of the previous update of the remote unit. Following a successful update, this field reads UPGRADE FINISHED SUCCESSFULLY. If an update was unsuccessful, the appropriate error message displays. Refer to DLP-5, Updating the Firmware Using TFTP, on page 103 for more details on available error messages. 612806420L1-1D Copyright © 2005 ADTRAN, Inc. 87 Section 5 User Interface Guide TRACER 6000 Series Integrated System Manual > RF LINK MANAGEMENT BRIDGE CONFIGURATION Figure 34 shows the RF Link Bridge Configuration menu page, which contains the parameters for enabling and configuring the TRACER 64x0 management bridge for passing information from the management port across the RF link to the remote end. Figure 34. RF Link Management Bridge Configuration >RF LINK MANAGEMENT BRIDGE CONFIGURATION > BRIDGE OPERATION The TRACER 64x0 has the capability to pass management information received on the local management port (MGMT) across the RF link to the remote end. This feature allows units to operate in a daisy-chain fashion, providing the user with configuration, management, and monitoring functions for all TRACER systems in the chain as well as any other Ethernet-capable device located on the same network segment as the TRACER systems. The TRACER 64x0 takes Ethernet traffic received on the local management port and determines (using a MAC bridge functionality) whether the traffic is intended for the local TRACER system or a system located over the RF link. If the BRIDGE OPERATION is ENABLED and Ethernet traffic is received on the MGMT interface for a remote TRACER system, the TRACER 64x0 bridges the data over the RF link. The RF Link Management Bridge feature is ENABLED by default. The RF Link Management Bridge feature should be used only to pass TRACER management information from one TRACER to another over the RF link. It is important to employ an IP addressing scheme that allows for independent networks at the local and all remote sites in the daisy-chain because the TRACER 64x0 will bridge all Ethernet traffic bound for a remote network over the RF link. Excessive bridge traffic can impede proper management operation; it is recommended that bridge traffic be limited to configuration, management, and monitoring functions. 88 Copyright © 2005 ADTRAN, Inc. 612806420L1-1D TRACER 6000 Series Integrated System Manual Section 5 User Interface Guide >RF LINK MANAGEMENT BRIDGE CONFIGURATION > INACTIVITY TIMEOUT Defines the amount of time that an Ethernet address is maintained in the bridge table. A shorter time produces a more dynamic bridge table, allowing addresses to change network segments without causing extra forwarded traffic. A longer time reduces the amount of unnecessarily forwarded traffic (due to unknown Ethernet addresses), but causes the bridge table to respond more slowly to a MAC address switching network segments. Valid choices are: 5 SEC (default), 15 SEC, 30 SEC, 1 MIN, and 5 MIN. > SYSTEM ALARMS Figure 35 shows the System Alarms menu page, which displays system alarm information for the link, fans, and temperature of the local and remote systems. System Alarm information is only available for the TRACER 6410. Figure 35. System Alarms > SYSTEM ALARMS > LINK ALARM Indicates the current status of the RF link between the local and remote TRACER 6410 systems. LINK UP indicates that the system detects a valid RF link and LINK DOWN indicates that the system does not detect a valid RF link. > SYSTEM ALARMS > FAN ALARMS Displays operational alarms for the system fans. An alarm is indicated when the system detects that the fan(s) rotational speed is below nominal operation and when the fan(s) is not functioning properly. Figure 36 on page 90 provides an example fan alarm. 612806420L1-1D Copyright © 2005 ADTRAN, Inc. 89 Section 5 User Interface Guide TRACER 6000 Series Integrated System Manual Figure 36. Active Fan Alarm > SYSTEM ALARMS > TEMP ALARMS Displays temperature alarm information for the system. An alarm is indicated when the system detects that the internal system temperature is elevated above normal operation. > SYSTEM ALARMS > PERSISTENT ALARMS Clears all current alarms listed on the SYSTEM ALARMS page. 90 Copyright © 2005 ADTRAN, Inc. 612806420L1-1D DETAIL LEVEL PROCEDURES Provides detailed instructions on performing common system tasks such as connecting to the system and upgrading firmware. CONTENTS DLP-1 Connecting a VT100 Terminal or PC to the CRAFT Port. . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 DLP-2 Logging into the TRACER 64x0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 DLP-3 Setting IP Parameters for the TRACER 64x0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 DLP-4 Verifying Communications Over an IP LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 DLP-5 Updating the Firmware Using TFTP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105 DLP-6 Updating the Firmware Using XMODEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 612806420L1-1D Copyright © 2005 ADTRAN, Inc. 91 Section 6 Detail Level Procedures 92 TRACER 6000 Series Integrated System Manual Copyright © 2005 ADTRAN, Inc. 612806420L1-1D DLP-1 Connecting a VT100 Terminal or PC to the CRAFT Port Introduction TRACER 64x0 management and provisioning are facilitated by a series of intuitive menus that are accessible on a computer screen. Connecting either a VT100 terminal or a PC with terminal emulation software to the CRAFT interface (DB-9) on the front of the unit allows access to TRACER menus and management features. This section specifies how to connect the VT100 terminal or PC to the TRACER 64x0. Prerequisite Procedures The TRACER 64x0 must be powered up for terminal communication to function. Tools and Materials Required • • A VT100 compatible terminal or PC with terminal emulation software An appropriate cable to connect the TRACER 64x0 to a terminal To prevent electrical shock, do not install equipment in a wet location or during a lightning storm. Electronic equipment can be damaged by static electrical discharge. Before handling it, put on an antistatic discharge wrist strap to prevent damage to electronic components. Place equipment in antistatic packing material when transporting or storing. When working on equipment, always place it on an approved antistatic mat that is electrically grounded. 612806420L1-1D Copyright © 2005 ADTRAN, Inc. 93 Section 6 DLP-1 TRACER 6000 Series Integrated System Manual Perform one of the following steps: 1. Connecting a VT100 terminal to the TRACER 64x0: • Set the parameters of the VT100 terminal or PC to: – 9600 baud rate – 8 data bits – No parity – 1 stop bit – No flow control • If the terminal has a parallel setting, disable this setting and use the serial port. Using the CRAFT Port • Plug the DB-9 male end of the data cable into the TRACER 64x0 CRAFT port on the front of the unit. Make the connection to the VT100 terminal as appropriate for your equipment. 2. Connecting a PC emulating a VT100 terminal to the TRACER 64x0: Most PCs or laptops can run communications software that emulates a VT100 terminal. Examples include Windows programs such as Terminal® or Hyperterminal®. However, there are many other adequate, commercially available software packages which will allow your PC or laptop to emulate a VT100 terminal. • Set the parameters of the communications software to: – 9600 baud rate – 8 data bits – No parity – 1 stop bit – No flow control • Set the PC for direct connect (instead of dial up connection) on the appropriate com port. Using the CRAFT Port • Plug the DB-9 male end of the data cable into the TRACER 64x0 CRAFT port on the front of the unit. Make connection to the PC or laptop as appropriate for your equipment. You are now ready to log in to the TRACER 64x0 as described in DLP-2, Logging into the TRACER 64x0, on page 95. 94 Copyright © 2005 ADTRAN, Inc. 612806420L1-1D DLP-2 Logging into the TRACER 64x0 Introduction Once you are connected to the TRACER 64x0, you must log into the system to gain access to the management and provisioning functions. This DLP assumes you are connected to the TRACER 64x0 and provides specific steps for logging into the system. Prerequisite Procedures Complete DLP-1, Connecting a VT100 Terminal or PC to the CRAFT Port, on page 93. To prevent electrical shock, do not install equipment in a wet location or during a lightning storm. Electronic equipment can be damaged by static electrical discharge. Before handling it, put on an antistatic discharge wrist strap to prevent damage to electronic components. Place equipment in antistatic packing material when transporting or storing. When working on equipment, always place it on an approved antistatic mat that is electrically grounded. see After the IP parameters have been provisioned (see DLP-3, Setting IP Parameters for the TRACER 64x0, on page 97), you can also log in via Telnet. 612806420L1-1D Copyright © 2005 ADTRAN, Inc. 95 Section 6 DLP-2 TRACER 6000 Series Integrated System Manual Perform the steps below in the order listed. 1. After connecting to the system, press any key to display the LOGIN screen shown here. The flashing cursor at the LOGIN field indicates that a password must be entered. 2. Enter the password for the TRACER 64x0 at the LOGIN field. The manufacturer’s default password for the TRACER 64x0 system is password in lowercase letters. 3. Upon entering the correct password, the TRACER 64x0 SYSTEM STATUS page is displayed as shown below. 4. You are now logged in to the TRACER 64x0 menu system. 96 Copyright © 2005 ADTRAN, Inc. 612806420L1-1D DLP-3 Setting IP Parameters for the TRACER 64x0 Introduction If the TRACER 64x0 is connected to an IP network for Telnet, TFTP, or SNMP management, several IP parameters must be set for the unit to communicate with the network. These parameters are described in this DLP along with the procedures for setting them. Please see your Network Administrator for the proper assignment of the following parameters: IP ADDRESS, SUBNET MASK, and DEFAULT GATEWAY. Prerequisite Procedures This procedure assumes that the TRACER 64x0 unit is connected to an IP network and is powered up. To prevent electrical shock, do not install equipment in a wet location or during a lightning storm. Electronic equipment can be damaged by static electrical discharge. Before handling it, put on an antistatic discharge wrist strap to prevent damage to electronic components. Place equipment in antistatic packing material when transporting or storing. When working on equipment, always place it on an approved antistatic mat that is electrically grounded. 612806420L1-1D Copyright © 2005 ADTRAN, Inc. 97 Section 6 DLP-3 TRACER 6000 Series Integrated System Manual Perform the steps below in the order listed. 1. Log into the system with maximum rights (details are in DLP-2, Logging into the TRACER 64x0, on page 95). 2. Press m to activate the Main menu page. From the Main menu page, press 7 to select MANAGEMENT/UTILITIES. 3. From the MANAGEMENT/UTILITIES page, select the MANAGEMENT/SNMP PORT CONFIGURATION option and press . 98 Copyright © 2005 ADTRAN, Inc. 612806420L1-1D TRACER 6000 Series Integrated System Manual Section 6 DLP-3 4. From the MANAGEMENT/SNMP CONFIGURATION menu page, select the IP ADDRESS field and press . Type the IP address provided by your network manager and press to accept the change. Repeat the process for the SUBNET MASK and DEFAULT GATEWAY options. The TRACER 64x0 is now available for Telnet access. Complete the steps outlined in DLP-4, Verifying Communications Over an IP LAN, on page 101. 612806420L1-1D Copyright © 2005 ADTRAN, Inc. 99 Section 6 DLP-3 100 TRACER 6000 Series Integrated System Manual Copyright © 2005 ADTRAN, Inc. 612806420L1-1D DLP-4 Verifying Communications Over an IP LAN Introduction When the 10/100BaseT/TX MGMT port is connected to a local area network (LAN), test steps must be performed on the TRACER 64x0 to ensure that the unit is communicating properly over the network. This procedure outlines those steps. Prerequisite Procedures Before beginning this procedure, the unit should be physically connected to the LAN and the provisioning tasks detailed in DLP-3, Setting IP Parameters for the TRACER 64x0, on page 97 should be complete. Tools and Materials Required • Access to a PC or other computer connected to the LAN To prevent electrical shock, do not install equipment in a wet location or during a lightning storm. Electronic equipment can be damaged by static electrical discharge. Before handling it, put on an antistatic discharge wrist strap to prevent damage to electronic components. Place equipment in antistatic packing material when transporting or storing. When working on equipment, always place it on an approved antistatic mat that is electrically grounded. 612806420L1-1D 101 Section 6 DLP-4 TRACER 6000 Series Integrated System Manual Perform the following steps in the order listed. 1. Verify the TRACER 64x0 IP address. If you do not already have the IP Address for the TRACER 64x0, obtain it from the network administrator or manually check for the address on the MANAGEMENT/SNMP CONFIGURATION page. (Access the MANAGEMENT/SNMP CONFIGURATION page by pressing 7 and then 1 from the Main menu page.) 2. Ping the TRACER 64x0 unit from a remote computer on the network. Using a remote computer system connected to the LAN, perform an ICMP ping on the IP address of the TRACER 64x0. Verify that the unit responds properly. If the TRACER 64x0 fails to respond, try the following: • Verify that the proper IP Address, subnet mask, and default gateway are provisioned in the unit (see DLP-3, Setting IP Parameters for the TRACER 64x0, on page 97, for details). • Verify that the TRACER 64x0 is properly cabled into the LAN and that the Ethernet cable is properly seated in the RJ-45 jack on the rear of the unit. • If the TRACER 64x0 is connected to a hub or other network device that provides a carrier sense light for each port, verify that the carrier sense light for the port to which the TRACER 64x0 is connected is lit. If this light is not lit, check the cabling between the hub and the shelf. The connection may also be verified using the activity LED located on the rear of the unit (part of the 10/100BaseT/TX MGMT RJ-45 connector). • Verify the IP address, subnet mask, and default gateway on the remote computer system. • If these steps fail, contact the LAN Administrator for assistance. Refer to the computer system’s documentation if you are unsure how to perform a ping command. Most computers running a networked version of Microsoft Windows™ or UNIX allow a ping to be performed by typing ping at a command line prompt. Typically, the ping program responds by indicating that the remote IP Address has responded in a certain amount of time or that no response was received. Some versions of ping continue running until you explicitly tell them to stop. If the program does not terminate on its own, type to stop the program. 102 612806420L1-1D TRACER 6000 Series Integrated System Manual Section 6 DLP-4 3. Telnet to the TRACER 64x0. From the same computer used in the previous step, Telnet to the TRACER 64x0 and verify that the Telnet session is properly opened. Once the Telnet session is established, press to logout of the session and return to the Login screen. Pressing again closes the Telnet session. Refer to the documentation of the computer system if you are unsure how to initiate a Telnet session. Most computers running a networked version of Microsoft Windows® or UNIX initiate a Telnet session by typing telnet at a command line prompt. The Windows XP HyperTerminal program also provides a Telnet client. Telnet is a utility common on many local area networks, and allows remote access to another computer or piece of equipment. 612806420L1-1D 103 Section 6 DLP-4 104 TRACER 6000 Series Integrated System Manual 612806420L1-1D DLP-5 Updating the Firmware Using TFTP Introduction The TRACER 64x0 supports firmware updates using TFTP or XMODEM. Use the 10/100BaseT/TX MGMT Ethernet port and TFTP from a network server or XMODEM (if your Telnet client supports file transfers), or use XMODEM and the CRAFT interface. This DLP provides the steps for a successful firmware upgrade using the 10/100 BaseT/TX MGMT Ethernet port and a TFTP server. (See DLP-6, Updating the Firmware Using XMODEM, on page 109 for instructions on using XMODEM.) Tools and Materials Required • • A PC with Telnet client software A TFTP server accessible on the network To prevent electrical shock, do not install equipment in a wet location or during a lightning storm. Electronic equipment can be damaged by static electrical discharge. Before handling it, put on an antistatic discharge wrist strap to prevent damage to electronic components. Place equipment in antistatic packing material when transporting or storing. When working on equipment, always place it on an approved antistatic mat that is electrically grounded. 612806420L1-1D Copyright © 2005 ADTRAN, Inc. 105 Section 6 DLP-5 TRACER 6000 Series Integrated System Manual Perform the following steps in the order listed. 1. Connect to the TRACER 64x0 using the 10/100BaseT/TX MGMT interface. If you are not already connected to the unit’s 10/100BaseT/TX MGMT port using Telnet client software, use the procedure in DLP-3, Setting IP Parameters for the TRACER 64x0, on page 97 to connect to the unit. 2. Press m to go to the Main menu page. 3. Select the MANAGEMENT/UTILITIES menu and press . 4. Select the FIRMWARE UPGRADE UTILITY menu and press . 5. Go to the FILE XFER METHOD menu and select TFTP. The TRACER 64x0 can use a TFTP server connected to the same Ethernet network as the local unit or a TFTP server connected to the same Ethernet network as the remote unit. Make the appropriate selection for your setup (choices are TFTP-LOCAL MGMT PORT or TFTP-REMOTE MGMT PORT). 6. Go to the TFTP SERVER field and enter the IP address of the network TFTP server. 7. Go to the TFTP FILENAME field and enter the filename of the firmware. TRACER 64x0 firmware files have a .bin extension. When specifying the filename, include the full path if the firmware file is not located in the TFTP default location. For example, to use a firmware file in the c:\firmware folder on your local machine, enter c:\firmware\myfirmware.bin into the TFTP FILENAME field. 8. Select the UPGRADE DESTINATION. Using TFTP provides the capability to upgrade both sections of the local and remote units. Valid choices are LOCAL IDU and REMOTE IDU. 9. View CURRENT UPDATE STATUS to verify the progress of the current firmware update or to identify any errors encountered during the download. During the TFTP upload, the following status messages display in CURRENT UPDATE STATUS to indicate the progress of the upload: 106 IDLE No active firmware upgrade. IDU RESET Indicates the firmware file transfer to the IDU is complete and the system is rebooting to load the new firmware. UPGRADE ABORTED Indicates the firmware upgrade was manually aborted by selecting ABORT from the COMMAND field. CONTACTING TFTP SERVER Indicates communication with the TFTP network server is trying to be established with the specified server address in the TFTP SERVER IP ADDRESS field. REQUESTING TFTP OF FILENAME Indicates the TRACER 64x0 is requesting TFTP access to the given update filename and path. Please verify appropriate user rights are selected for the specified path. TFTP TRANSFER IN PROGRESS Indicates communication with the TFTP network server has been established and the update file is being transferred between the TRACER 64x0 and the TFTP network server. UPGRADE IMAGE IS VALID Indicates that the system image was verified as a valid image for the specified update. Before the firmware upgrade begins, the TRACER 64x0 verifies that the image is valid. If it is not valid for the system, UPGRADE IMAGE IS INVALID displays. Copyright © 2005 ADTRAN, Inc. 612806420L1-1D TRACER 6000 Series Integrated System Manual Section 6 DLP-5 UPGRADE IMAGE IS INVALID Indicates that the system image was not verified as a valid image for the specified update. Before the firmware upgrade begins, the TRACER 64x0 verifies that the image is valid. If it is not valid for the system, UPGRADE IMAGE IS INVALID displays. WAITING FOR SC TRANSFER TO BEGIN Indicates that the local system is waiting to transfer the firmware upgrade information to the remote system over the service channel. Service channel communications over the RF link allow a user connected to a local system to upgrade the firmware of a remote system. Before the remote system begins the firmware upgrade process, a complete copy of the new firmware image must be received and stored in the remote system. This is done automatically when the remote system is chosen from the UPGRADE DESTINATION field. RECEIVING SC TRANSFER Indicates that the system is receiving the firmware upgrade information from the remote system over the service channel. Service channel communications over the RF link allow a user connected to a local system to upgrade the firmware of a remote system. Before the remote system begins the firmware upgrade process, a complete copy of the new firmware image must be received and stored in the remote system. This is done automatically when the remote system is chosen from the UPGRADE DESTINATION field. READY TO BEGIN SENDING SC Indicates that the local system is ready to transfer the firmware upgrade TRANSFER information to the remote system over the service channel. Service channel communications over the RF link allow a user connected to a local system to upgrade the firmware of a remote system. Before the remote system begins the firmware upgrade process, a complete copy of the new firmware image must be received and stored in the remote system. This is done automatically when the remote system is chosen from the UPGRADE DESTINATION field. SENDING SC TRANSFER Indicates that the local system is sending the firmware upgrade information to the remote system over the service channel. Service channel communications over the RF link allow a user connected to a local system to upgrade the firmware of a remote system. Before the remote system begins the firmware upgrade process, a complete copy of the new firmware image must be received and stored in the remote system. This is done automatically when the remote system is chosen from the UPGRADE DESTINATION field. VERIFYING FLASH IMAGE Indicates that the system flash image is being verified as a valid image for the specified update. Before the new firmware is loaded into the local flash, the TRACER 64x0 verifies that the flash image is valid for the new firmware. If it is not valid for the system, the firmware upgrade fails. ERASING FLASH Indicates that the system flash is being erased so the new firmware image can be loaded into the local flash. Before the new firmware is loaded into the local flash, the TRACER 64x0 verifies that the flash image is valid for the new firmware. If it is not valid for the system, the firmware upgrade fails. PROGRAMMING FLASH Indicates that the new firmware image is being loaded into the local flash. Before the new firmware is loaded into the local flash, the TRACER 64x0 verifies that the flash image is valid for the new firmware. If it is not valid for the system, the firmware upgrade fails. 612806420L1-1D Copyright © 2005 ADTRAN, Inc. 107 Section 6 DLP-5 TRACER 6000 Series Integrated System Manual REQUIRED COMMUNICATIONS LINK IS DOWN Indicates that a problem with the RF link or the service channel is preventing a successful remote system firmware upgrade. Before a firmware upgrade begins, the system verifies that communication between all required parts is operational. If this check fails, the firmware upgrade fails. UPGRADE FAILED Indicates that the firmware upgrade was unsuccessful. UPGRADE FINISHED SUCCESSFULLY Indicates that the firmware upgrade completed successfully and the new firmware should be loaded and running. 10. When the update has successfully completed, IDLE displays in the CURRENT UPDATE STATUS field and UPGRADE FINISHED SUCCESSFULLY displays in the PREVIOUS UPDATE STATUS field. The TRACER 64x0 will restart immediately and resume operation. During reset and initialization, the RF link between the units will not be operational. 108 Copyright © 2005 ADTRAN, Inc. 612806420L1-1D DLP-6 Updating the Firmware Using XMODEM Introduction The TRACER 64x0 supports firmware updates of the local and remote systems using TFTP or XMODEM. Use the 10/100BaseT/TX MGMT port and TFTP from a network server or XMODEM (if your Telnet client supports file transfers), or use XMODEM and the CRAFT interface. This procedure outlines the steps for a successful firmware upgrade using the CRAFT interface and XMODEM software. The same XMODEM steps apply for file transfers through your Telnet client (refer to your Telnet client documentation for more details on file transfer specifics). (See DLP-5, Updating the Firmware Using TFTP, on page 105 for instructions on using TFTP.) Tools and Materials Required • • VT100 terminal or PC with VT100 terminal emulation software XMODEM software To prevent electrical shock, do not install equipment in a wet location or during a lightning storm Electronic equipment can be damaged by static electrical discharge. Before handling it, put on an antistatic discharge wrist strap to prevent damage to electronic components. Place equipment in antistatic packing material when transporting or storing. When working on equipment, always place it on an approved antistatic mat that is electrically grounded. 612806420L1-1D Copyright © 2005 ADTRAN, Inc. 109 Section 6 DLP-6 TRACER 6000 Series Integrated System Manual Perform the following steps in the order listed. 1. Connect to the TRACER 64x0 using the front panel DB-9 CRAFT interface. If you are not already connected to the unit’s CRAFT interface (either with a VT100 compatible terminal or with a PC running VT100 emulation software), follow the procedure in DLP-1, Connecting a VT100 Terminal or PC to the CRAFT Port, on page 93. Connecting to the CRAFT interface limits the upgrade procedure to XMODEM only. 2. Log in to the unit (see DLP-2, Logging into the TRACER 64x0, on page 95 for details). 3. Press m to go to the Main menu page. 4. Select the MANAGEMENT/UTILITIES menu and press . 5. Select the FIRMWARE UPGRADE UTILITY menu and press . 6. Go to the FILE XFER METHOD menu and select XMODEM. 7. Select the UPGRADE DESTINATION. (Valid selections for XMODEM are LOCAL IDU and LOCAL ODU). 8. View CURRENT UPDATE STATUS to verify the progress of the current firmware update or to identify any errors encountered during the download. 9. Select START from the COMMAND menu to start the update. When the TRACER 64x0 is ready to receive the XMODEM upload, the menu screen clears and displays XMODEM waiting for start.... twice to Cancel. If this does not appear, please review the steps above for possible configuration errors. 10. From the terminal emulation software, begin the XMODEM upload by using the appropriate command sequence. This may take several minutes. If necessary, refer to the terminal emulation software documentation for help. Also, when specifying the filename, ensure that the file transferred is the one provided by ADTRAN. Otherwise, the update will not complete successfully. Because XMODEM data is being transferred inband through the menu interface, the VT100 menus of the TRACER 64x0 will be inoperable from the CRAFT interface. You can cancel the update at any time within the terminal emulation software. (Please consult the documentation provided by the terminal emulation software to determine how to do this). 11. When the update has successfully completed, IDLE displays in the CURRENT UPDATE STATUS field and UPGRADE FINISHED SUCCESSFULLY displays in the PREVIOUS UPDATE STATUS field. The TRACER 64x0 will restart immediately and resume operation. During reset and initialization, the RF link between the units will not be operational. Alternatively, if the unit is part of a management cluster connected to the local network, you may use a PC connected to the network to Telnet into the unit. By using the 10/100BaseT/TX MGMT port, the TRACER 64x0 may be quickly upgraded using TFTP, provided there is a TFTP server on the local network. (See DLP-5, Updating the Firmware Using TFTP, on page 105 for more details.) 110 Copyright © 2005 ADTRAN, Inc. 612806420L1-1D MIBS Provides a listing of SNMP Management Information Bases (MIBs) supported by the TRACER 64x0. This section also lists traps supported for each MIB. CONTENTS MIBs Supported by the TRACER 64x0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112 MIB Compilation Order . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112 Traps Supported by the TRACER 64x0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113 MIB Variables Supported by the TRACER 64x0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116 TABLES Table 1. Table 2. Table 3. Table 4. Table 5. Table 6. MIBs Supported by the TRACER 64x0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112 MIB Compilation Order . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112 Traps Supported by the TRACER 64x0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113 MIB Variables for ad.mi2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116 MIB Variables for ads1.mi2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116 MIB Variables for TRACER6000.mib . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117 612806420L1-1D Copyright © 2005 ADTRAN, Inc. 111 Section 7 MIBs 1. TRACER 6000 Series Integrated System Manual MIBS SUPPORTED BY THE TRACER 64x0 Table 1 lists the MIBs supported by the TRACER 64x0. Table 1. MIBs Supported by the TRACER 64x0 rfc2495.mib Standard – DS1 and E1 interface types rfc2863.mib IF MIB – updated MIB II needed for RFC2495 rfc3418.mib SNMPv2 MIB rfc3593.mib PerfHist-TC-MIB needed for RFC2495 rfc3635.mib EtherLike MIB adtran.mi2 ADTRAN product MIB needed to locate the ADTRAN specific MIBs on the MIB node tree ianaif.mib IF MIB needed for RFC2863 ads1.mi2 ADTRAN DS1 MIB tracer6000.mib TRACER 6000 series modular MIB SNMPv2-SMI, SNMPv2-TC, and SNMPv2-CONF are not compiled, but the paths to these files are required by your MIB compiler during setup. 2. MIB COMPILATION ORDER MIBs are compiled in the order shown in Table 2. Table 2. MIB Compilation Order rfc3418.mib ianaif.mib rfc2863.mib rfc3593.mib rfc3635.mib rfc2495.mib adtran.mi2 ads1.mi2 tracer6000.mib 112 Copyright © 2005 ADTRAN, Inc. 612806420L1-1D TRACER 6000 Series Integrated System Manual 3. Section 7 MIBs TRAPS SUPPORTED BY THE TRACER 64x0 The TRACER 64x0 supports the traps described in Table 3. Table 3. Traps Supported by the TRACER 64x0 MIB Trap This trap indicates that.... TRACER6000.mib adTRACERColdStart 612806420L1-1D the unit has powered up. adTRACERYellow a change in the YELLOW alarm state has occurred and the YELLOW alarm is now active. adTRACERAIS a change in the Alarm Indication Signal (AIS) has occurred and the AIS alarm is active. adTRACERRedAlarm a change in the RED alarm state has occurred and the RED alarm is now active. adTRACERLOS a change in the Loss of Signal (LOS) state has occurred and the LOS alarm is active. adTRACERBPV a change in the BiPolar Violation (BPV) state has occurred and the BPV alarm is active. adTRACERRA a change in the Frame RA (Remote Alarm) state has occurred and the RA alarm is active. adTRACEROOF a change in the Out Of Frame (OOF) state has occurred and the OOF alarm is active. adTRACERCV a change in the Code Violation (CV) state has occurred and the CV alarm is active. adTRACERCRC a change in the Cyclic Redundancy Check (CRC) state has occurred and the CRC alarm is active. adTRACERmfLOF a change in the Loss of Multiframe (LOMF) state has occurred and the LOMF alarm is active. adTRACERmfLOS a change in the Multiframe Loss of Signal (LOS) state has occurred and the Multiframe LOS alarm is active. adTRACERmfAIS a change in the Multiframe Alarm Indication Signal (AIS) state has occurred and the Multiframe AIS alarm is active. adTRACERmfRA a change in the Multiframe Remote Alarm (RA) has occurred and the Multiframe RA alarm is active. adTRACERlineLoopback a change in the line loopback state has occurred and the line loopback is active. adTRACERlinkLoopback a change in the link loopback state has occurred and the link loopback is active. adTRACERYellowOff a change in the YELLOW alarm state has occurred and the YELLOW alarm is now inactive. adTRACERAISoff a change in the Alarm Indication Signal (AIS) has occurred and the AIS alarm is inactive. adTRACERRedAlarmOff a change in the RED alarm state has occurred and the RED alarm is now inactive. adTRACERLOSoff a change in the Loss of Signal (LOS) state has occurred and the LOS alarm is inactive. Copyright © 2005 ADTRAN, Inc. 113 Section 7 MIBs TRACER 6000 Series Integrated System Manual Table 3. Traps Supported by the TRACER 64x0 (Continued) MIB Trap This trap indicates that.... TRACER6000.mib adTRACERBPVoff 114 a change in the BiPolar Violation (BPV) state has occurred and the BPV alarm is inactive. adTRACERRAoff a change in the Frame RA (Remote Alarm) state has occurred and the RA alarm is inactive. adTRACEROOFoff a change in the Out Of Frame (OOF) state has occurred and the OOF alarm is inactive. adTRACERCVoff a change in the Code Violation (CV) state has occurred and the CV alarm is inactive. adTRACERCRCoff a change in the Cyclic Redundancy Check (CRC) state has occurred and the CRC alarm is inactive. adTRACERmfLOFoff a change in the Loss of Multiframe (LOMF) state has occurred and the LOMF alarm is inactive. adTRACERmfLOSoff a change in the Multiframe Loss of Signal (LOS) state has occurred and the Multiframe LOS alarm is inactive. adTRACERmfAISoff a change in the Multiframe Alarm Indication Signal (AIS) state has occurred and the Multiframe AIS alarm is inactive. adTRACERmfRAoff a change in the Multiframe Remote Alarm (RA) has occurred and the Multiframe RA alarm is inactive. adTRACERlineLoopbackOff a change in the line loopback state has occurred and the line loopback is inactive. adTRACERlinkLoopbackOff a change in the link loopback state has occurred and the link loopback is inactive. adTRACERLinkDown the RF link is down. adTRACERLinkUp the RF link is up. adTRACERRFCLinkDown the RFC link is down between the Indoor Unit (IDU) and Outdoor Unit (ODU). This trap only applies to TRACER split systems. adTRACERRFCLinkUp the RFC link is up between the IDU and ODU. This trap only applies to TRACER split systems. adTRACERRxLow the receive level is within 10 dB of sensitivity and the RF Low alarm is active. adTRACERRxLevel a change in receive level has occurred and the receive level is within normal range. adTRACERcurrThrsESon the threshold for current Errored Seconds (ES) has been exceeded. adTRACERcurrThrsESoff the threshold for current ES has not been exceeded. adTRACERcurrThrsSESon the threshold for current Severely Errored Seconds (SES) has been exceeded. adTRACERcurrThrsSESoff the threshold for current SES has not been exceeded. Copyright © 2005 ADTRAN, Inc. 612806420L1-1D TRACER 6000 Series Integrated System Manual Section 7 MIBs Table 3. Traps Supported by the TRACER 64x0 (Continued) MIB Trap This trap indicates that.... TRACER6000.mib adTRACERtotalThrsESon the threshold for Total ES has been exceeded. adTRACERtotalThrsESoff the threshold for Total ES has not been exceeded. adTRACERtotalThsSESon the threshold for Total SES has been exceeded. adTRACERtotalThsSESoff the threshold for Total SES has not been exceeded. adTRACERfan1Alarm* fan 1 currently has an active alarm. adTRACERfan1Fail* fan 1 has failed. adTRACERfan1AlarmOff* the fan 1 alarm has turned off after it was activated. adTRACERfan1On* fan 1 has turned back on after a fan 1 failure. adTRACERfan2Alarm* fan 2 currently has an active alarm. adTRACERfan2Fail* fan 2 has failed. adTRACERfan2AlarmOff* the fan 2 alarm has turned off after it was activated. adTRACERfan2On* fan 2 has turned back on after a fan 2 failure. adTRACERtempAlarm* the temperature alarm has turned on due to an increase in internal temperature. adTRACERtempAlarmOff* the temperature alarm has turned off due to a decrease in internal temperature. adTRACERtxshutdown* the transmitter has shut down due to temperature constraints. * Listed traps only apply to TRACER high power systems. 612806420L1-1D Copyright © 2005 ADTRAN, Inc. 115 Section 7 MIBs 4. TRACER 6000 Series Integrated System Manual MIB VARIABLES SUPPORTED BY THE TRACER 64X0 Table 4. MIB Variables for ad.mi2 ad adProducts adProductInfo adProdName DisplayString RO adProdPartNumber DisplayString RO adProdCLEIcode DisplayString RO adProdSerialNumber DisplayString RO adProdRevision DisplayString RO adProdSwVersion DisplayString RO adProdPhysAddress PhysAddress RO DisplayString RO adDS1AlarmIndex Integer RO adDS1AlarmEnable Integer RW adDS1LineEvent Integer RO adDS1LineArm Integer RW adDS1AlertIndex Integer RO adDS1AlertEnable Integer RW adDS1CurrentAlert Integer RO adDS1TotalAlert Integer RO adDS1FarCurrentAlert Integer RO adDS1FarTotalAlert Integer RO adProdProductID adProdTransType adMgmt adAdmin adPerform adShared adIdentity adIdentityShared adAgentCapModule adAgentCapProduct adAgentCapShared adConformance adCompliances Table 5. MIB Variables for ads1.mi2 adDS1AlarmTable adDS1AlarmEntry adDS1AlertTable adDS1AlertEntry 116 Copyright © 2005 ADTRAN, Inc. 612806420L1-1D TRACER 6000 Series Integrated System Manual Section 7 MIBs Table 5. MIB Variables for ads1.mi2 (Continued) adDS1CurrentArm Integer RW adDS1TotalArm Integer RW adDS1FarCurrentArm Integer RW adDS1FarTotalArm Integer RW adDS1CurrentThrsES Integer RW adDS1CurrentThrsSES Integer RW adDS1CurrentThrsSEFS Integer RW adDS1CurrentThrsUAS Integer RW adDS1CurrentThrsCSS Integer RW adDS1CurrentThrsPCVsf Integer RW adDS1CurrentThrsPCVesf Integer RW adDS1CurrentThrsLES Integer RW adDS1CurrentThrsLCV Integer RW adDS1TotalThrsES Integer RW adDS1TotalThrsSES Integer RW adDS1TotalThrsSEFS Integer RW adDS1TotalThrsUAS Integer RW adDS1TotalThrsCSS Integer RW adDS1TotalThrsPCVsf Integer RW adDS1TotalThrsPCVesf Integer RW adDS1TotalThrsLES Integer RW adDS1TotalThrsLCV Integer RW adTRACERRFlinkState DisplayString RO adTRACERRFClinkState* DisplayString RO adTRACERrfLow DisplayString RO adTRACERRXquality DisplayString RO adTRACERRXLevel DisplayString RO adTRACERFrequencyPlan DisplayString RO adTRACERLEDStatus DisplayString RO adTRACERSlot1 DisplayString RO adTRACERSlot2 DisplayString RO adDS1CurrentThreshold adDS1TotalThreshold Table 6. MIB Variables for TRACER6000.mib adTRACER6000mg adTRACER6000status * Listed variable only applies to TRACER split systems. 612806420L1-1D Copyright © 2005 ADTRAN, Inc. 117 Section 7 MIBs TRACER 6000 Series Integrated System Manual Table 6. MIB Variables for TRACER6000.mib (Continued) adTRACER6000cfg adTRACERBaudRate Integer RW adTRACERBandPlan Integer RW adTRACERactiveChannels Integer RW adTRACERdsx1ChannelSelectIdx Integer RO adTRACERdsx1ChannelSelection Integer RW adTRACERswitchChannelSelectIdx Integer RO adTRACERswitchChannelSelection Integer RW DisplayString RW adTRACERalarmNumber Integer RO adTRACERAlarmReporting Integer RW adTRACERClearHistory Integer RW adTRACERrfTrapEnable Integer RW adTRACERswitchPortIdx Integer RO adTRACERswitchPortEnable Integer RO adTRACERswitchPortSpeedDuplex Integer RW adTRACERswitchPortStatusIdx Integer RO adTRACERswitchPortTxPackets Integer RO adTRACERswitchPortTxPacketsDrop Integer RO adTRACERswitchPortRxPackets Integer RO adTRACERswitchPortRxPacketsDrop Integer RO adTRACERswitchPortRxPacketError Integer RO adTRACERchannelSelect adTRACERdsx1ChannelSelectTable adTRACERdsx1ChannelSelectEntry AdTRACERdsx1ChannelSelectEntry adTRACERswitchChannelSelectTable adTRACERswitchChannelSelectEntry AdTRACERswitchChannelSelectEntry adTRACERTxPower adTRACERalarmTable adTRACERalarmEntry AdTRACERAlarmEntry adTRACERswitchModuleCfg adTRACERswitchPortCfgTable adTRACERswitchPortCfgEntry AdTRACERswitchPortCfgEntry adTRACERswitchModuleStatus adTRACERswitchPortStatusTable adTRACERswitchPortStatusEntry AdTRACERswitchPortStatusEntry 118 Copyright © 2005 ADTRAN, Inc. 612806420L1-1D TRACER 6000 Series Integrated System Manual Section 7 MIBs Table 6. MIB Variables for TRACER6000.mib (Continued) adTRACERswitchWanStatusTable adTRACERswitchWanStatusEntry AdTRACERswitchWanStatusEntry adTRACERswitchWanStatusIdx Integer RO adTRACERswitchWanTxPackets Integer RO adTRACERswitchWanTxPacketsDrop Integer RO adTRACERswitchWanRxPackets Integer RO adTRACERswitchWanRxPacketsDrop Integer RO adTRACERswitchWanRxPacketError Integer RO adTRACERfan1* Display String RO adTRACERfan1AlarmTripped* Display String RO adTRACERfan2* Display String RO adTRACERfan2AlarmTripped* Display String RO adTRACERtemperature* Display String RO adTRACERtemperatureTripped* Display String RO adTRACERtransmitter* Display String RO adTRACERClearFanAlarms* Integer RW adTRACERIpAddress IpAddress RO adTRACERSubnetMask IpAddress RO adTRACERGatewayIp IpAddress RO adTRACERTrapIpHost1 IpAddress RW adTRACERTrapIpHost2 IpAddress RW adTRACERTrapIpHost3 IpAddress RW adTRACERTrapIpHost4 IpAddress RW adTRACERTrapIpHost5 IpAddress RW adTRACERcsu1IntervalIndex Integer RO adTRACERcsu1IntervalNumber Integer RO adTRACERintervalCSU1Aes Integer RO adTRACERintervalCSU1Ases Integer RO adTRACERintervalCSU1Bes Integer RO adTRACERintervalCSU1Bses Integer RO adTRACERintervalCSU1Ces Integer RO adTRACERintervalCSU1Cses Integer RO adTRACER6000FanStatus* adTRACER6000ip adTRACER6000trapIP adTRACERcsu1IntervalTable adTRACERcsu1IntervalEntry AdTRACERcsu1IntervalEntry * Listed variable only applies to TRACER high power systems. 612806420L1-1D Copyright © 2005 ADTRAN, Inc. 119 Section 7 MIBs TRACER 6000 Series Integrated System Manual Table 6. MIB Variables for TRACER6000.mib (Continued) adTRACERintervalCSU1Des Integer RO adTRACERintervalCSU1Dses Integer RO adTRACERIntervalValidData TruthValue RO adTRACERcsu2IntervalIndex Integer RO adTRACERcsu2IntervalNumber Integer RO adTRACERintervalCSU2Aes Integer RO adTRACERintervalCSU2Ases Integer RO adTRACERintervalCSU2Bes Integer RO adTRACERintervalCSU2Bses Integer RO adTRACERintervalCSU2Ces Integer RO adTRACERintervalCSU2Cses Integer RO adTRACERintervalCSU2Des Integer RO adTRACERintervalCSU2Dses Integer RO adTRACERIntervalValidData TruthValue RO adTRACERcurrentRFs Integer RO adTRACERcurrent24hRFs Integer RO adTRACERcurrentRFCs* Integer RO adTRACERcurrent24hRFCs* Integer RO adTRACERcurrentRxLs Integer RO adTRACERcurrentMaxRxLs Integer RO adTRACERcurrent24hMaxRxLs Integer RO adTRACERcurrentMinRxLs Integer RO adTRACERcurrent24hMinRxLs Integer RO adTRACERcurrentRxQs Integer RO adTRACERcurrentMaxRxQs Integer RO adTRACERcurrent24hMaxRxQs Integer RO adTRACERcurrentMinRxQs Integer RO adTRACERcurrent24hMinRxQs Integer RO adTRACERintervalIndex Integer RO adTRACERintervalNumber Integer RO adTRACERintevalRFs Integer RO adTRACERcsu2IntervalTable adTRACERcsu2IntervalEntry AdTRACERcsu2IntervalEntry adTRACER6000current adTRACERintervalTable adTRACERintervalEntry AdTRACERintervalEntry * Listed variable only applies to TRACER split systems. 120 Copyright © 2005 ADTRAN, Inc. 612806420L1-1D TRACER 6000 Series Integrated System Manual Section 7 MIBs Table 6. MIB Variables for TRACER6000.mib (Continued) adTRACERintervalRFCs* Integer RO adTRACERintervalMaxRxLs Integer RO adTRACERintervalMinRxLs Integer RO adTRACERintervalMaxRxQs Integer RO adTRACERintervalMinRxQs Integer RO adTRACERintervalValidData TruthValue RO adTRACERtotalNumber Integer RO adTRACERtotalRFs Integer RO adTRACERtotalRFCs* Integer RO adTRACERtotalMaxRxLs Integer RO adTRACERtotalMinRxLs Integer RO adTRACERtotalMaxRxQs Integer RO adTRACERtotalMinRxQs Integer RO adTRACERtotalValidData TruthValue RO adTRACERremoteRFlinkState DisplayString RO adTRACERremoteRFClinkState* DisplayString RO adTRACERremoteRFLow DisplayString RO adTRACERremoteRXquality DisplayString RO adTRACERremoteRXLevel DisplayString RO adTRACERremoteFrequencyPlan DisplayString RO adTRACERremoteLEDStatus DisplayString RO adTRACERremoteSlot1 DisplayString RO adTRACERremoteSlot2 DisplayString RO adTRACERremoteBaudRate Integer RW adTRACERremoteBandPlan Integer RW adTRACERremoteActiveChannels Integer RW adTRACERremoteDSX1ChannelSelectIdx Integer RO adTRACERremoteDSX1ChannelSelection Integer RW adTRACERtotalTable adTRACERtotalEntry AdTRACERtotalEntry adTRACER6000remoteStatus adTRACER6000remoteCfg adTRACERremoteChannelSelect adTRACERremoteDSX1ChannelSelectTable adTRACERremoteDSX1ChannelSelectEntry AdTRACERremoteDSX1ChannelSelectEntry adTRACERremoteSwitchChannelSelectTable * Listed variable only applies to TRACER split systems. 612806420L1-1D Copyright © 2005 ADTRAN, Inc. 121 Section 7 MIBs TRACER 6000 Series Integrated System Manual Table 6. MIB Variables for TRACER6000.mib (Continued) AdTRACERremoteSwitchChannelSelectEntry adTRACERremoteSwitchChannelSelectEntry adTRACERremoteSwitchChannelSelectIdx Integer RO adTRACERremoteSwitchChannelSelection Integer RW DisplayString RW adTRACERremoteAlarmNumber Integer RO adTRACERremoteAlarmReporting Integer RW Integer RW adTRACERremoteSwitchPortIdx Integer RO adTRACERremoteSwitchPortEnable Integer RO adTRACERremoteSwitchPortSpeedDuplex Integer RW adTRACERremoteSwitchPortStatusIdx Integer RO adTRACERremoteSwitchPortTxPackets Integer RO adTRACERremoteSwitchPortTxPacketsDrop Integer RO adTRACERremoteSwitchPortRxPackets Integer RO adTRACERremoteSwitchPortRxPacketsDrop Integer RO adTRACERremoteSwitchPortRxPacketError Integer RO adTRACERremoteSwitchWanStatusIdx Integer RO adTRACERremoteSwitchWanTxPackets Integer RO adTRACERremoteSwitchWanTxPacketsDrop Integer RO adTRACERremoteSwitchWanRxPackets Integer RO adTRACERremoteSwitchWanRxPacketsDrop Integer RO adTRACERremoteSwitchWanRxPacketError Integer RO adTRACERremoteFan1 DisplayString RO adTRACERremoteFan1AlarmTripped DisplayString RO adTRACERremoteTxPower adTRACERremoteAlarmTable AdTRACERremoteAlarmEntry adTRACERremoteAlarmEntry adTRACERremoteClearHistory adTRACERremoteSwitchModuleCfg adTRACERremoteSwitchPortCfgTable adTRACERremoteSwitchPortCfgEntry AdTRACERremoteSwitchPortCfgEntry adTRACERremoteSwitchModuleStatus adTRACERremoteSwitchPortStatusTable adTRACERremoteSwitchPortStatusEntry AdTRACERremoteSwitchPortStatusEntry adTRACERremoteSwitchWanStatusTable adTRACERremoteSwitchWanStatusEntry AdTRACERremoteSwitchWanStatusEntry 122 Copyright © 2005 ADTRAN, Inc. 612806420L1-1D TRACER 6000 Series Integrated System Manual Section 7 MIBs Table 6. MIB Variables for TRACER6000.mib (Continued) adTRACERremoteFan2 DisplayString RO adTRACERFan2AlarmTripped DisplayString RO adTRACERremoteTemperature DisplayString RO adTRACERremoteTemperatureTripped DisplayString RO adTRACERremoteTransmitter DisplayString RO adTRACERremoteClearFanAlarms Integer RW adTRACERremoteTrapIpHost1 IpAddress RW adTRACERremoteTrapIpHost2 IpAddress RW adTRACERremoteTrapIpHost3 IpAddress RW adTRACERremoteTrapIpHost4 IpAddress RW adTRACERremoteTrapIpHost5 IpAddress RW adTRACERremotecsu1IntervalIndex Integer RO adTRACERremotecsu1IntervalNumber Integer RO adTRACERremoteintervalCSU1Aes Integer RO adTRACERremoteintervalCSU1Ases Integer RO adTRACERremoteintervalCSU1Bes Integer RO adTRACERremoteintervalCSU1Bses Integer RO adTRACERremoteintervalCSU1Ces Integer RO adTRACERremoteintervalCSU1Cses Integer RO adTRACERremoteintervalCSU1Des Integer RO adTRACERremoteintervalCSU1Dses Integer RO adTRACERremoteIntervalValidData TruthValue RO adTRACERremotecsu2IntervalIndex Integer RO adTRACERremotecsu2IntervalNumber Integer RO adTRACERremoteintervalCSU2Aes Integer RO adTRACERremoteintervalCSU2Ases Integer RO adTRACERremoteintervalCSU2Bes Integer RO adTRACERremoteintervalCSU2Bses Integer RO adTRACERremoteintervalCSU2Ces Integer RO adTRACERremoteintervalCSU2Cses Integer RO adTRACERremoteintervalCSU2Des Integer RO adTRACERremoteintervalCSU2Dses Integer RO adTRACERremoteIntervalValidData TruthValue RO adTRACER6000remoteTrapIP adTRACERremotecsu1IntervalTable adTRACERremotecsu1IntervalEntry AdTRACERremotecsu1IntervalEntry adTRACERremotecsu2IntervalTable adTRACERremotecsu2IntervalEntry AdTRACERremotecsu2IntervalEntry 612806420L1-1D Copyright © 2005 ADTRAN, Inc. 123 Section 7 MIBs TRACER 6000 Series Integrated System Manual Table 6. MIB Variables for TRACER6000.mib (Continued) adTRACERremoteCurrent adTRACERremoteCurrentRFs Integer RO adTRACERremoteCurrent24hRFs Integer RO adTRACERremoteCurrentRFCs* Integer RO adTRACERremoteCurrent24hRFCs* Integer RO adTRACERremoteCurrentRxLs Integer RO adTRACERremoteCurrentMaxRxLs Integer RO adTRACERremoteCurrent24hMaxRxLs Integer RO adTRACERremoteCurrentMinRxLs Integer RO adTRACERremoteCurrent24hMinRxLs Integer RO adTRACERremoteCurrentRxQs Integer RO adTRACERremoteCurrentMaxRxQs Integer RO adTRACERremoteCurrent24hMaxRxQs Integer RO adTRACERremoteCurrentMinRxQs Integer RO adTRACERremoteCurrent24hMinRxQs Integer RO adTRACERremoteIntervalIndex Integer RO adTRACERremoteIntervalNumber Integer RO adTRACERremoteIntevalRFs Integer RO adTRACERremoteIntervalRFCs* Integer RO adTRACERremoteIntervalMaxRxLs Integer RO adTRACERremoteIntervalMinRxLs Integer RO adTRACERremoteIntervalMaxRxQs Integer RO adTRACERremoteIntervalMinRxQs Integer RO adTRACERremoteIntervalValidData TruthValue RO adTRACERremoteTotalNumber Integer RO adTRACERremoteTotalRFs Integer RO adTRACERremoteTotalRFCs* Integer RO adTRACERremoteTotalMaxRxLs Integer RO adTRACERremoteTotalMinRxLs Integer RO adTRACERremoteTotalMaxRxQs Integer RO adTRACERremoteTotalMinRxQs Integer RO adTRACERremoteTotalValidData TruthValue RO adTRACERremoteIntervalTable AdTRACERremoteIntervalEntry adTRACERremoteIntervalEntry adTRACERremoteTotalTable AdTRACERremoteTotalEntry adTRACERremoteTotalEntry * Listed variable only applies to TRACER split systems. 124 Copyright © 2005 ADTRAN, Inc. 612806420L1-1D TROUBLESHOOTING GUIDE Provides helpful information for troubleshooting common configuration problems for the TRACER 64x0. CONTENTS Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126 LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126 PWR LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126 TST LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126 RF DWN LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126 RF LOW LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 T1 Interface Alarms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 E1 Interface Alarms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 LAN LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129 RF Errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129 Step-by-Step Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129 Installing/Troubleshooting the TRACER Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130 Installing/Configuring T1 Hardware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131 Installing/Configuring E1 Hardware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131 Installing/Configuring Ethernet Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132 612806420L1-1D Copyright © 2005 ADTRAN, Inc. 123 Section 8 Troubleshooting Guide 1. TRACER 6000 Series Integrated System Manual OVERVIEW This troubleshooting guide recommends corrective actions for various conditions of the TRACER 64x0 system. The status LEDs (located on the front panel of the unit) provide information to help determine the necessary troubleshooting action. This guide suggests steps for resolving possible problems indicated by the status LEDs. 2. LED INDICATORS PWR LED If the PWR LED is not ON and solid green, the TRACER 64x0 is not receiving adequate DC power. Recommended Actions: 1. Verify that the power source is delivering between 21 and 60 VDC. 2. Check the polarity of the power connection (referenced to ground) of both the TRACER 64x0 unit and the power source. 3. Check the internal fuse. The fuse is accessed from the rear panel of the unit. If this fuse is open, replace it with a 2 A, 250 V (2-inch) slow-blo fuse. TST LED The TST LED will flash once (amber) during power-up to indicate a self-test is in progress. If the TST LED is flashing or remains ON after 10 seconds, the TRACER 64x0 unit has failed the self-test. This is an internal failure, and Technical Support should be contacted. RF DWN LED If the RF DWN LED is ON (solid red), there is a problem with the RF receive path from the remote TRACER 64x0. Recommended Actions: 1. Verify that one end of the link is configured as frequency plan A and the other end as frequency plan B. 2. Verify that both ends of the link are configured for the same band plan (1, 2, or 3). 3. Measure the RSSI voltage and consult the RSSI calibration sheet included with the unit. If the voltage level corresponds to a received signal power level that agrees with the calculated receive signal level, proceed with Step 7. 4. Check the RF coaxial cable connection. 5. Verify that the antenna polarization is the same at both ends of the RF signal transmit and receive path. 6. Verify the RF signal path is clear. 7. Check the integrity of the lightning arrestors. 8. Check for possible interference at both ends of the link. If necessary, change polarization and/or band plans at both ends. 124 Copyright © 2005 ADTRAN, Inc. 612806420L1-1D TRACER 6000 Series Integrated System Manual Section 8 Troubleshooting Guide RF LOW LED If the RF LOW LED is ON (solid red), the received signal is approaching 0 V of RSSI. This condition is typically indicative of a path or installation problem. Recommended Actions: 1. Verify the far-end transmitter power setting is the value that the link planning budget allows. 2. Check all coaxial cable connectors for solid connections. Check for water and corrosion around any of the connectors. If water is apparent in the coaxial connectors, replace the coaxial cable and the connectors, making sure to properly weatherproof the replacements. 3. Verify the RF signal path by verifying the antenna alignment. 4. Check the integrity of lightning arrestors. T1 Interface Alarms All active T1 alarms are displayed in the T1X STATUS/CONFIGURATION/LOOPBACK menu page.To identify the T1 interface in alarm and the specific alarm present, display the T1(X) STATUS screens and check the T1(X) INTERFACE ALARMS field. Recommended Actions: 1. Display the T1(X) STATUS screen and check the T1(X) INTERFACE ALARM field to identify the active alarm. 2. Follow the steps below for the appropriate alarm. LOS Alarm or Red Alarm LOS ALARM and RED ALARM are indications that the TRACER 64x0 may be unable to detect a viable T1 received signal from the connected T1 equipment. This error may be due to a degraded signal or no signal, or may be caused by improper framing. Recommended Actions: 1. Verify that the T1 cable is connected to the T1 interface on the TRACER 64x0. 2. Verify the connections at the opposite end of the T1 cable. 3. Verify that the framing mode (D4 or ESF) is the same for both the TRACER 64x0 and the T1 equipment. Yellow Alarm A Yellow Alarm is generated by the attached equipment. When the attached equipment’s T1 interface is in Red Alarm, the TRACER 64x0 generates a Yellow Alarm. Recommended Actions: 1. Follow the troubleshooting steps for Red Alarm, but do so at the attached equipment. Blue Alarm A remote alarm (alarm indication signal or AIS) is generated by the attached equipment. The root cause must be determined at the attached equipment. A typical cause of a blue alarm is a lack of input to a CSU. Recommended Actions: 1. Verify the input to any attached data equipment. 612806420L1-1D Copyright © 2005 ADTRAN, Inc. 125 Section 8 Troubleshooting Guide TRACER 6000 Series Integrated System Manual BPV Bipolar violations (BPVs) indicate an improper configuration or faulty wiring. Recommended Actions: 1. Verify the TRACER 64x0 unit and the attached equipment are configured for the same line coding (B8ZS or AMI). 2. Verify the cable connections for the T1 interface are solid. E1 Interface Alarms All active E1 alarms are displayed on the E1X STATUS/CONFIGURATION/LOOPBACK menu page. To identify the E1 interface in alarm and the specific alarm present, display the E1(X) STATUS screens and check the E1(X) INTERFACE ALARMS field. Recommended Actions: 1. Display the E1(X) STATUS screen and check the E1(X) INTERFACE ALARM field to identify the active alarm. 2. Follow the steps below for the appropriate alarm. LOS Alarm (Loss of Signal) LOS ALARM is an indication that the TRACER 64x0 may be unable to detect a viable E1 received signal from the connected E1 equipment. This error may be due to a degraded signal or no signal, or may be caused by improper framing. Recommended Actions: 1. Verify that the E1 cable is connected to the E1 interface on the TRACER 64x0. 2. Verify the connections at the opposite end of the E1 cable. 3. Verify that the framing mode (framed, multiframed, or unframed) is the same for both the TRACER 64x0 and the E1 equipment. AIS Alarm A remote alarm (alarm indication signal or AIS) is generated by the attached equipment. The root cause must be determined at the attached equipment. A typical cause of a blue alarm is a lack of input to a CSU. Recommended Actions: 1. Verify the input to any attached data equipment. LCV Line code violations (LCVs) indicate that the received E1 stream contains an invalid line code and are generally caused by an improper configuration or faulty wiring. Recommended Actions: 1. Verify the TRACER 64x0 unit and the attached equipment are configured for the same line coding (HDB3 or AMI). 2. Verify the cable connections for the E1 interface are solid. 126 Copyright © 2005 ADTRAN, Inc. 612806420L1-1D TRACER 6000 Series Integrated System Manual Section 8 Troubleshooting Guide CRC CRC errors indicate that the receiver is unable to synchronize to the CRC-4 frame pattern of the received E1 signal. Recommended Actions: 1. Verify the TRACER 64x0 unit and the attached equipment are configured for the same signaling (MULTIFRAMED, UNFRAMED, or FRAMED). 2. Verify the cable connections for the E1 interface are solid. LAN LEDs If the LAN LED is OFF, the TRACER 64x0 is not able to detect an active Ethernet link on the particular 10/100BaseT/TX interface. Recommended Actions: 1. Check all Ethernet cable connections to verify they are properly plugged in (making sure the tab on the connector snaps into place). 2. Connect the 10/100BaseT/TX interface to a “known good” Ethernet port to verify the TRACER port is functioning properly. 3. Try another Ethernet cable. 3. RF ERRORS RF errors can range from a nonviable microwave path to loose RF connectors. Nonviable path conditions could be caused by physical obstructions such as buildings, mountainous terrain, trees, etc., as well as other physical limitations such as excessive path distances and in-band RF interference. These types of errors are remedied by performing a detailed line-of-site microwave path study to determine whether a microwave link is feasible for the terrain and environment under consideration. If after performing a microwave path study the system is still not operational, ensure that the antennas are properly aligned. Note that alignment must be achieved in both elevation and azimuth for optimal link performance. The TRACER 64x0 can be used to aid in antenna alignment by looking at the real-time signal strength numbers or the RX POWER “fuel gauge” on the SYSTEM STATUS or SYSTEM OPTION menu pages or by measuring the DC voltage (relative to ground) at the RSSI front panel test jack. Optimal antenna alignment is achieved by peaking the front panel RSSI voltage or the RX POWER “fuel gauge” on the TRACER 64x0 terminal display. Consult the ADTRAN TRACER Data Sheet included with the unit to verify that the actual receive signal level agrees with the calculated receive signal. An RSSI test point, located on the front panel, provides a DC voltage level (relative to the GND test point) that corresponds to the amount of signal being received from the far end’s transmitter. The voltage at this test point can vary from approximately 0 to 5 VDC. An RSSI calibration sheet is shipped with the system to provide the installer a cross-reference between actual received signal level (in dBm) and RSSI voltage. This sheet is useful for verifying link budget calculations and ensuring proper equipment installation. 4. STEP-BY-STEP TROUBLESHOOTING The logical troubleshooting flow presented in this section can be used to set up your TRACER 64x0 system or to diagnose a previously installed system. Please contact Technical Support at any stage during installation and/or troubleshooting if you require assistance. 612806420L1-1D Copyright © 2005 ADTRAN, Inc. 127 Section 8 Troubleshooting Guide 5. TRACER 6000 Series Integrated System Manual INSTALLING/TROUBLESHOOTING THE TRACER HARDWARE 1. Perform a detailed path profile and link budget for each TRACER 64x0 microwave link. A thorough path study can be used to estimate signal power budgets, estimate fade margins at each receiver, identify potential line-of-site obstacles, properly size antenna dishes, and determine minimum antenna dish heights above the earth. 2. Set up all of the TRACER 64x0 hardware on a workbench. The actual cables used in the permanent installation should be used in the workbench setup. A rigorous workbench “simulation” of the link will help alleviate and avoid time-consuming errors. 3. Examine the PLAN A and PLAN B LEDs on the front panel of each unit. These LEDs indicate the frequency plan for each TRACER 64x0 unit. Each TRACER link must have a Plan A radio on one side and a Plan B radio on the other. 4. Attach the RF coaxial cables to be used in the permanent installation to the N-type connectors on the back of the TRACER 64x0 unit. Attach the other end of the coaxial cable(s) to an RF power meter or spectrum analyzer, if either is available. The power measured by the meter/analyzer is the RF power available at the input of the antenna. The TRACER 64x0 unit is programmed at the factory to output approximately 100 mW (20 dBm) of RF power. The actual power level measured by the meter/analyzer will be less than 100 mW due to RF losses through the coaxial cable, and is a function of the cable type and length being used. In any event, the power level at the output of the coaxial cable should be a significant fraction of 100 mW. A power meter/analyzer reading that is not on the order of at least tens-of-milliwatts could be an indication of unsuitable RF cable or faulty or unreasonably long coaxial cable, or a combination of these factors. 5. Resolve all RF coaxial cabling errors before proceeding. 6. Attach the RF coaxial cables to a high-quality attenuator, if possible. If you do not have an attenuator, attach the coaxial cables to the antennas to be used in the permanent installation. If the installation antennas are not available, small, inexpensive dipole or patch antennas can be used for verification purposes. If an adjustable attenuator is being used, dial in the amount of attenuation that corresponds to the path loss value expected for the microwave link in which the TRACER hardware will be installed. The path loss value can be calculated from a knowledge of the path length, or provided by a path study. Remember to subtract both antenna gain values from the attenuator level if these values have not already been accounted for. 7. After setting up the RF pieces, examine the RF DOWN LED on the front panel of each TRACER 64x0 unit. If the RF DOWN LED is illuminated (red), the corresponding TRACER 64x0 is not receiving a suitable RF signal from the other TRACER 64x0 unit. In this case, the receiving TRACER 64x0 is either receiving a very weak signal or no signal at all. If the RF DOWN LED is not illuminated, then the TRACER 64x0 units are receiving a suitable RF signal. Suitable RF power levels for low error rate communication range from -30 dBm to -88 dBm measured at the N-type connector input on the TRACER 64x0 unit. 8. Resolve any signal level issues before proceeding. 9. Examine the RF LOW LED on the front panel of each TRACER 64x0. If this LED is illuminated, then the TRACER 64x0 is receiving a relatively weak signal; however, if the RF DOWN LED is not illuminated, then the received signal is being suitably processed by the TRACER 64x0 system. If you are receiving a weak signal (RF LOW is ON), please verify that the weak signal is not being caused by a faulty cable, an insufficiently tightened cable, or some other installation-related problem. Also, make sure an unreasonably large attenuation value has not been selected if you are using an attenuator on a workbench setup. 128 Copyright © 2005 ADTRAN, Inc. 612806420L1-1D TRACER 6000 Series Integrated System Manual Section 8 Troubleshooting Guide Use the tables in Section 2, Microwave Path Engineering Basics, on page 15, of this manual to select the proper free-space attenuation value (in dB) based on the estimated length of the microwave path. Remember to subtract both antenna gains (local and remote) from the attenuator setting. 10. Test the installed modules by performing the following steps: 4xT1 Module Initiate a line loopback on the local TRACER 64x0 unit and run a test pattern from the connected T1 equipment. This will verify the connection between the T1 equipment and the local TRACER 64x0 unit. Quad Ethernet Switch Module Connect a computer (or Ethernet test equipment) to the TRACER 64x0 Ethernet interfaces. Perform a “ping” from one test station across the wireless link to another test station connected to the remote TRACER 64x0. This will verify the data path between the test equipment and the TRACER 64x0 unit. 4xE1 Module Initiate a line loopback on the local TRACER 64x0 unit and run a test pattern from the connected E1 equipment. This will verify the connection between the E1 equipment and the local TRACER 64x0 unit. 11. Command a link loopback on the remote TRACER 64x0 unit and run a test pattern from the connected T1 equipment. This will verify the data path across the RF link. External pattern generators are required to test data path integrity. A T1/E1 BER tester is suggested. Installing/Configuring T1 Hardware 1. If possible, attach any or all of the intended T1 hardware to the TRACER 64x0 units using the same workbench setup. This step offers the perfect opportunity to configure your T1 hardware for proper functioning with the TRACER 64x0 hardware. 2. To significantly reduce the probability of an unsuccessful field installation, resolve any remaining T1 equipment-to-TRACER 64x0 configuration issues before field installation. See T1 Interface Alarms on page 125 for more information on resolving T1 interface alarm conditions. Installing/Configuring E1 Hardware 1. If possible, attach any or all of the intended E1 hardware to the TRACER 64x0 units using the same workbench setup. This step offers the perfect opportunity to configure your E1 hardware for proper functioning with the TRACER 64x0 hardware. 2. To significantly reduce the probability of an unsuccessful field installation, resolve any remaining E1 equipment-to-TRACER 64x0 configuration issues before field installation. See E1 Interface Alarms on page 126 for more information on resolving E1 interface alarm conditions. 612806420L1-1D Copyright © 2005 ADTRAN, Inc. 129 Section 8 Troubleshooting Guide TRACER 6000 Series Integrated System Manual Installing/Configuring Ethernet Hardware 1. If possible, attach any or all of the intended Ethernet hardware to the TRACER 64x0 units using the same workbench setup. This step offers the perfect opportunity to configure your Ethernet hardware for proper functioning with the TRACER hardware. 2. To significantly reduce the probability of an unsuccessful field installation, resolve any remaining Ethernet equipment-to-TRACER 64x0 configuration issues before field installation. 130 Copyright © 2005 ADTRAN, Inc. 612806420L1-1D


Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 130
Page Mode                       : UseOutlines
Has XFA                         : No
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:fb708904-b65d-4189-9994-f85d7aa59459
Producer                        : Acrobat Distiller 6.0 (Windows)
Create Date                     : 2005:09:16 13:38:18Z
Creator Tool                    : FrameMaker 7.0
Modify Date                     : 2006:07:21 11:32:08-04:00
Metadata Date                   : 2006:07:21 11:32:08-04:00
Document ID                     : uuid:82669dff-4135-48eb-befa-53adea1305a9
Format                          : application/pdf
Title                           : TRACER 6000 Series Integrated System Manual
Description                     : TRACER 6000 Series Wireless Products
Creator                         : ADTRAN, Inc.
Tagged PDF                      : Yes
Author                          : ADTRAN, Inc.
Subject                         : TRACER 6000 Series Wireless Products
EXIF Metadata provided by EXIF.tools
FCC ID Filing: HDCTRC6410L2X

Navigation menu