Abocom Systems CAS1040 IP Sharing Fast EtherSwitch For Cable/ xDSL Modem User Manual INTRODUCTION

Download:
Mirror Download [FCC.gov]
Document ID	164257
Application ID	Pqs07frDUPVcgMQu1tepiA==
Document Description	users manual 3
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	101.04kB (1263032 bits)
Date Submitted	2001-08-13 00:00:00
Date Available	2001-08-10 00:00:00
Creation Date	2001-08-13 08:39:05
Producing Software	Acrobat Distiller 5.0 (Windows)
Document Lastmod	2001-08-13 08:39:12
Document Title	INTRODUCTION
Document Creator	Acrobat PDFMaker 5.0 for Word
Document Author:	user8

Management from Internet: Checking this item lets you manage this device remotely
from outside of the network through Telnet or Web Configuration.
Note: to reduce the risk of hacker attack, it is better to leave this box unchecked.
Factory Reset Device Configuration: Click Factory Reset and all current settings on the
device will be reset to the default values.
SAVE: After completing the settings on this page, click “SAVE” to save the settings.
RESET: Click “RESET” to clear all the settings on this page.
Local Port
This screen contains settings for LAN interface attached to the local network.
- 17 -
IP Address
•
Default: 192.168.1.254
SubNetmask
•
Default: 255.255.255.0
~Do not distribute IP address to local computers5
Checking this radio button to disable this IP Sharing device to distribute IP Addresses
(DHCP disabled).
~Distribute IP addresses to local computers
Checking this radio button to enable this IP Sharing device to distribute IP Addresses (DHCP
enabled). And the following field will be activated for you to enter the starting IP Address:
Continuous IP address pool starts at
The starting address of this local IP network address pool. The pool is a piece of continous IP
address segment. Keep the default value 192.168.1.1 should work for most cases.
Number of IP address in pool
•
Maximum: 128. Default value 128 should work for most cases.
Note: If “Continuous IP address poll starts” is set at 192.168.1.1 and the “Number of IP
address in pool” is 128, the device will distribute IP addresses from 192.168.1.1 to
192.168.1.128 to all the computers in the network that request IP addresses from DHCP
server (IP Sharing Device).
If you check this selection, remember you have to specify a static IP address for all your local computers.
- 18 -
SAVE: After completing the settings on this page, click “SAVE” to save the settings.
RESET: Click “RESET” to clear all the settings on this page.
Global Port
This screen contains settings for the Global (Internet connection) interface.
Adapter Address: Read-only. It is necessary for some ISP to identify this device by its MAC
address.
Device/Computer Name: Enter a descriptive name for identification purpose. Some Internet
Service Providers (ISP) requires this information and if that is the case, they will provide you
with the name. The Maximum input for this field is 20 alphanumeric characters and it is case
sensitive.
Domain Name: For example: yourcompany.com. The maximum input for this field is 32
alphanumeric characters and it is case insensitive.
Note: Your ISP may ask you to input a certain domain name. Domain name is also required
for internal network’s email and news functions.
~Obtain configuration automatically (CATV dynamic mode): For Cable Modem Internet
service.
~PPPoE (DSL dynamic mode): For xDSL Internet service that runs PPPoE. If your xDSL
service uses PPPoE, after installing the IP Sharing device, please do not run PPPoE software
on your computers.
- 19 -
~Static configuration: Check this button when the ISP assigns static IP address for your
account.
PPPoE Account Info (enter information provided by ISP when PPPoE is selected)
Username:
•
Maximum input is 52 alphanumeric characters (case sensitive).
Password:
•
Maximum input is 36 alphanumeric characters (case sensitive).
Service Name: For identification purpose. If it is required, your ISP will provide you the
information.
Auto-disconnect: This device can be configured to auto-disconnect when there is no activity
on the line for a predetermined period of time.
•
Default: 5 minutes. You can input any number from 0 to 65535.
•
To keep the line always connected, please set the number to 0.
Link Status (Read-Only): Displays the current PPPoE link status (for PPPoE only). It
shows either “PPPoE connected” or “PPPoE disconnected”.
Internet Port Configuration: For CATV dynamic mode or PPPoE (DSL dynamic mode),
user can get new settings by pressing the Release and then the Renew button. For Static
configuration, however, these two buttons are grayed out since user will enter these
addresses by using information provided by the ISP.
IP address: Enter the information provided by your ISP in case of Static configuration.
Subnet Mask: Enter the information provided by your ISP in case of Static configuration.
Gateway: Enter the information provided by your ISP in case of Static configuration.
- 20 -
DNS server #1: /DNS server #2:
When the Internet Station is setup to “Obtain global port configuration automatically” and
it is connected to the ISP, it will obtain these two addresses from ISP automatically. You can
change the values according to ISP’s instruction.
SAVE: After completing the settings on this page, click “SAVE” to save the settings.
RESET: Click “RESET” to clear all the settings on this page.
Virtual Server
ADD Server
Single Port/Port Range: For selecting between a specific port and a range of ports which
you want the Internet users to be able to access. The valid port number ranges from 0 to
65535.
Port Type: please select the port type (TCP or UDP) for the port number that was entered
earlier.
Local Server IP Address: Enter the Local Server’s IP address (for the specified port entered
above).
ADD: Click “ADD” to add the local server in the Server List.
Note: Maximum 12 Server (port) entries are allowed and each port number can only be
assigned to one IP address.
RESET: Click “RESET” to clear the settings on the page.
Server List: The Local Server IP Addresses will appear on the screen.
List: If there is any Local Server in the Server List, click on the down arrow  to select the
desired Server Number on the list.
DELETE: After selecting the Server Number in the “List”, click on “DELETE” to remove
the Server from the list. You can only delete one Server at a time.
- 21 -

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Modify Date                     : 2001:08:13 08:39:12-04:00
Create Date                     : 2001:08:13 08:39:05-04:00
Title                           : INTRODUCTION
Author                          : user8
Creator                         : Acrobat PDFMaker 5.0 for Word
Producer                        : Acrobat Distiller 5.0 (Windows)
Page Count                      : 5

EXIF Metadata provided by EXIF.tools