Allied Telesis K K AP500 Cloud-Managed Enterprise-class Wireless Access Point with IEEE802.11a/b/g/n/ac Dual Radio User Manual at002286a
Allied Telesis K.K. Cloud-Managed Enterprise-class Wireless Access Point with IEEE802.11a/b/g/n/ac Dual Radio at002286a
Contents
- 1. Users Manual
- 2. Users Manual_revised0119
- 3. Users Manual_0208
Users Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2969665 |
| Application ID | kept3LJzQ1oTqHpb7gDTSw== |
| Document Description | Users Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 180.42kB (2255227 bits) |
| Date Submitted | 2016-04-26 00:00:00 |
| Date Available | 2016-04-27 00:00:00 |
| Creation Date | 2016-02-01 10:48:08 |
| Producing Software | Acrobat Distiller 9.0.0 (Windows) |
| Document Lastmod | 2016-04-25 22:55:15 |
| Document Title | at002286a.book |
| Document Creator | FrameMaker 12.0.4 |
| Document Author: | wshrank |
Review Draft 4-25-16 AT-AP500 Cloud-Managed Enterprise-class Wireless Access Point with IEEE802.11a/b/g/n/ac Dual Radio Installation Guide 613-002286 Rev. A Review Draft 4-25-16 Copyright 2016 Allied Telesis, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesis, Inc. Allied Telesis and the Allied Telesis logo are trademarks of Allied Telesis, Incorporated. All other product names, company names, logos or other designations mentioned herein are trademarks or registered trademarks of their respective owners. Allied Telesis, Inc. reserves the right to make changes in specifications and other information contained in this document without prior written notice. The information provided herein is subject to change without notice. In no event shall Allied Telesis, Inc. be liable for any incidental, special, indirect, or consequential damages whatsoever, including but not limited to lost profits, arising out of or related to this manual or the information contained herein, even if Allied Telesis, Inc. has been advised of, known, or should have known, the possibility of such damages. Review Draft 4-25-16 Electrical Safety and Emissions Standards This product meets the following standards: Federal Communications Commission Interference Statement Declaration of Conformity Manufacturer Name: Allied Telesis, Inc. Declares that the product: Wireless access point with PoE+ powered device function Model Number: AT-AP500 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. E80 Avertissement Avertissement de la FCC: Les changements ou modifications non expressément approuvés par la partie responsable de la conformité pourraient annuler l'autorité de l'utilisateur à utiliser cet équipement. E80 Review Draft 4-25-16 This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. For operation within 5150-5250MHz / 5470-5725MHz frequency range, it is restricted to indoor environment.The band from 5600-5650MHz will be disabled by the software during the manufacturing and cannot be changed by the end user. This device meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 26cm between the radiator & your body. Safety and Electromagnetic Emissions Certificates Electromagnetic Compatibility (EMC) ICES-003 Class B Radio Equipment FCC 47 CFR Part 15, Subpart C FCC 47 CFR Part 15, Subpart E FCC OET Bulletin No. 65 Supplement C RSS-Gen, Issue No. 4 RSS-102, Issue No. 5 RSS-247, Issue No. 1 Safety UL 60950-1 2nd Edition CAN/CSA C22.2 No. 60950-1 Translated Safety Statements Important: The indicates that a translation of the safety statement is available in a PDF document titled Translated Safety Statements on the Allied Telesis website at www.alliedtelesis.com/support. Review Draft 4-25-16 Contents Preface ............................................................................................................................................................11 Safety Symbols Used in this Document ..................................................................................................... 12 Contacting Allied Telesis............................................................................................................................ 13 Chapter 1: Overview ......................................................................................................................................15 Features ..................................................................................................................................................... 16 Rear Panel Components............................................................................................................................ 17 LAN Port..................................................................................................................................................... 19 Power over Ethernet............................................................................................................................ 19 Connector Type ................................................................................................................................... 19 Speed .................................................................................................................................................. 19 Duplex Mode ....................................................................................................................................... 19 Maximum Distance .............................................................................................................................. 19 Cable Requirements............................................................................................................................ 19 Automatic MDIX Detection .................................................................................................................. 20 Port Pinouts ......................................................................................................................................... 20 LEDs .......................................................................................................................................................... 21 Reset Button .............................................................................................................................................. 22 Chapter 2: Installing the Access Point ........................................................................................................23 Reviewing Safety Precautions ................................................................................................................... 24 Unpacking the AT-AP500 Access Point..................................................................................................... 26 Installing the Access Point on a Wall or Ceiling ......................................................................................... 27 Guidelines............................................................................................................................................ 27 Mounting the Base Plate to the Wall or Ceiling ................................................................................... 28 Attaching the Mounting Bracket to the Access Point........................................................................... 29 Attaching the Access Point to the Base Plate ..................................................................................... 30 Cabling the Access Point..................................................................................................................... 31 Kensington Lock......................................................................................................................................... 34 Starting the Initial Management Session on the Access Point................................................................... 35 Requirements ...................................................................................................................................... 35 Starting the Management Session ...................................................................................................... 35 Appendix A: Technical Specifications ........................................................................................................37 Physical Specifications............................................................................................................................... 37 Environmental Specifications ..................................................................................................................... 37 Power Specifications.................................................................................................................................. 38 LAN Port..................................................................................................................................................... 39 Safety and Electromagnetic Emissions Certifications ................................................................................ 41 Appendix B: Regulatory Statements ...........................................................................................................43 Federal Communication Commission Interference Statement................................................................... 44 Contents Review Draft 4-25-16 Review Draft 4-25-16 Figures Figure 1: Rear Panel Components .................................................................................................................. Figure 2: AT-TQ0091 AC/DC Power Adapter.................................................................................................. Figure 3: Ventilation Slots................................................................................................................................ Figure 4: Base Plate Hole Dimensions............................................................................................................ Figure 5: Mounting Base Plate ........................................................................................................................ Figure 6: Bottom of Access Point .................................................................................................................... Figure 7: Locking Bracket to Access Point ...................................................................................................... Figure 8: Attaching the Mounting-Bracket Screw ............................................................................................ Figure 9: Attaching Access Point to Base Plate .............................................................................................. Figure 10: Connecting the Network Cable....................................................................................................... Figure 11: Connecting the Power Cable from the AT-TQ0091 AC/DC Adapter.............................................. Figure 12: Removing an AC Plug from the AT-TQ0091 AC/DC Power Adapter ............................................. Figure 13: Installing an AC Plug on the AT-TQ0091 AC/DC Power Adapter .................................................. Figure 14: Kensington Lock............................................................................................................................. Figure 15: Pin Layout for the RJ45 Connector on the LAN Port...................................................................... 17 26 27 28 28 29 29 30 30 31 32 32 33 34 39 List of Figures Review Draft 4-25-16 Review Draft 4-25-16 Tables Table 1. Components on the Rear Panel ....................................................................................................... 17 Table 2. Twisted Pair Cable for the LAN Port ................................................................................................. 20 Table 3. LEDs on the AT-AP500 Access Point .............................................................................................. 21 Table 4. AT-AP500 Physical Specifications ................................................................................................... 37 Table 5. Environmental Specifications ........................................................................................................... 37 Table 6. AT-AP500 Maximum Power Consumption ....................................................................................... 38 Table 7. AT-TQ0091 Power Adapter .............................................................................................................. 38 Table 8. LAN Port Specifications .................................................................................................................... 39 Table 9. MDI Pin Signals (10Base-T or 100Base-TX) .................................................................................... 39 Table 10. MDI-X Pin Signals (10Base-T or 100Base-TX) .............................................................................. 40 Table 11. 1000Base-T Connector Pinouts ..................................................................................................... 40 Table 12. Safety and Electromagnetic Emissions Certificates ....................................................................... 41 List of Tables 10 Preface This guide contains the hardware installation instructions for the AT-AP500 Wireless Access Point. This preface contains the following sections: “Safety Symbols Used in this Document” on page 12 “Contacting Allied Telesis” on page 13 11 Preface Safety Symbols Used in this Document This document uses the following conventions. Note Notes provide additional information. Caution Cautions inform you that performing or omitting a specific action may result in equipment damage or loss of data. Warning Warnings inform you that performing or omitting a specific action may result in bodily injury. 12 AT-AP500 Wireless Access Point Installation Guide Contacting Allied Telesis If you need assistance with this product, you may contact Allied Telesis technical support by going to the Support & Services section of the Allied Telesis web site at www.alliedtelesis.com/support. You can find links for the following services on this page: 24/7 Online Support — Enter our interactive support center to search for answers to your product questions in our knowledge database, check support tickets, learn about Return Merchandise Authorizations (RMAs), and contact Allied Telesis technical experts. USA and EMEA phone support — Select the phone number that best fits your location and customer type. Hardware warranty information — Learn about Allied Telesis warranties and register your product online. Replacement Services — Submit an RMA request via our interactive support center. Documentation — View the most recent installation and user guides, software release notes, white papers, and data sheets for your products. Software Downloads — Download the latest software releases for your managed products. For sales or corporate information, go to www.alliedtelesis.com/ purchase. 13 Preface 14 Chapter 1 Overview This chapter describes the hardware components of the AT-AP500 Wireless Access Point. This chapter contains the following sections: “Features” on page 16 “Rear Panel Components” on page 17 “LAN Port” on page 19 “LEDs” on page 21 “Reset Button” on page 22 15 Chapter 1: Overview Features The main features of the product are listed here: Dual concurrent radio: 2.4 GHz and 5 GHz IEEE 802.11a/b/g/n/ac MIMO with internal omni antennas — 2.4 GHz radio: 3x3:3ss — 5 GHz radio: 4x4:4ss 16 Maximum capacity 2.4 GHz: 450 Mbps Maximum capacity 5 GHz: 2,200 Mbps Rogue access point detection Multiple SSIDs One 10/100/1000Base-T Ethernet port with Auto-Negotiation, auto MDI/MDIX, and IEEE 802.3at Power over Ethernet (PoE+) IEEE 802.3 (10Base-T), IEEE 802.3u (100Base-TX), and IEEE 802.3ab (1000Base-T) compliance on the Ethernet port MAC address filtering for wireless access security Broadcast and multicast rate limiting Virtual access points for multiple broadcast domains DHCP client WPA-Personal and WPA-Enterprise with WPA, WPA2, TKIP, and CCMP (AES) authentication and encryption Static WEP encryption Cloud-managed from AlliedView™ Cloud Quality of Service Wall or ceiling installation AT-AP500 Wireless Access Point Installation Guide Rear Panel Components The rear panel components of the AT-AP500 Access Point are illustrated in Figure 1. Kensington Lock Reset Button LAN Port DC Power Connector Console Port Figure 1. Rear Panel Components The components are listed in Table 1. Table 1. Components on the Rear Panel Field Description Kensington Lock Lock to secure the access point. For information, refer to “Kensington Lock” on page 34. Console Port The Console port is for manufacturing purposes only. Reset Button Reboots the unit. For information, refer to “Reset Button” on page 22. LAN Port The LAN port connects the access point to your wired network. It supports PoE+. If you connect the port to an Ethernet switch that supports PoE+, you do not have to use the AC/DC adapter to power the device. For information, refer to “LAN Port” on page 19. 17 Chapter 1: Overview Table 1. Components on the Rear Panel (Continued) Field DC Power Connector 18 Description This connector is for the AT-TQ0091 Power Adapter. The access point can be powered with PoE+ on the LAN port or the power adapter. The AT-TQ0091 Power Adapter does not come with the access point. It must be ordered separately from Allied Telesis. AT-AP500 Wireless Access Point Installation Guide LAN Port The LAN port is used to connect the device to your Local Area Network (LAN), typically through an Ethernet switch. Power over Ethernet The AT-AP500 Access Point supports Power over Ethernet (PoE+) on the LAN port. The unit is a PoE+ class 4 powered device with a maximum power consumption of 16 watts. When the port is connected to a PoE+ Ethernet switch, the unit receives its power over the network cable that carries the network traffic. If you use the PoE+ feature, you do not need to use the AC/DC power adapter that has to be purchased separately. Connector Type The LAN port has an eight-pin RJ45 connector. The port uses four pins at 10 or 100 Mbps and all eight pins at 1000 Mbps. The pin assignments are listed in “LAN Port” on page 39. Speed The LAN port can operate at 10, 100, or 1000 Mbps. The speed is set automatically with Auto-Negotiation. You cannot disable Auto-Negotiation on the port. Note The LAN port should be connected to a network device that also adjusts its speed with Auto-Negotiation. If the network device does not support Auto-Negotiation, the LAN port operates at 10 Mbps, which may reduce network performance. Duplex Mode The LAN port can operate in either half- or full-duplex mode at 10 or 100 Mbps, and full-duplex mode at 1000 Mbps. The port is IEEE 802.3ucompliant and uses Auto-Negotiation to set the duplex mode. (You cannot disable Auto-Negotiation on the port.) Note The LAN port should be connected to a network device that also sets its duplex mode with Auto-Negotiation. If the network device does not support Auto-Negotiation, the LAN port operates at halfduplex mode. This may result in a duplex mode mismatch if the network device is operating at full-duplex. Maximum Distance Cable Requirements The LAN port has a maximum operating distance of 100 meters (328 feet). The cable requirements for the LAN port are listed in Table 2 on page 20. 19 Chapter 1: Overview Table 2. Twisted Pair Cable for the LAN Port 10Mbps Cable Type Automatic MDIX Detection 100Mbps 1000Mbps PoE+ NonPoE+ PoE+ NonPoE+ PoE+ Standard TIA/EIA 568- Yes B-compliant Category 3 shielded or unshielded cabling with 100 ohm impedance and 16 MHz frequency. No No No No No Standard TIA/EIA 568A-compliant Category 5 shielded or unshielded cabling with 100 ohm impedance and 100 MHz frequency. Yes Yes Yes Yes No No Standard TIA/EIA 568B-compliant Enhanced Category 5 (Cat 5e) shielded or unshielded cabling with 100 ohm impedance and 100 MHz frequency. Yes Yes Yes Yes Yes Yes Standard TIA/EIA 568B-compliant Category 6 or 6a shielded cabling. Yes Yes Yes Yes Yes Yes NonPoE+ The 10/100/1000 Mbps twisted-pair port is IEEE 802.3ab compliant and features automatic MDIX detection when operating at 10 or 100 Mbps. (Automatic MDIX detection does not apply to 1000 Mbps.) This feature automatically configures the port to MDI or MDI-X, depending on the wiring configuration of the port on the Ethernet switch. You may not disable automatic MDIX detection. For automatic MDIX detection to work properly, it must also be present on the Ethernet switch. The LAN port defaults to MDIX if it is connected to a network device that does not support automatic MDIX detection. Port Pinouts 20 Refer to Table 9 on page 39 for the port pinouts of the LAN port when it is operating at 10 or 100 Mbps in the MDI configuration and Table 10 on page 40 for the MDI-X configuration. Refer to Table 11 on page 40 for the port pinouts when the port is operating at 1000 Mbps. AT-AP500 Wireless Access Point Installation Guide LEDs The LEDs on the AT-AP500 Access Point are described in Table 3. Table 3. LEDs on the AT-AP500 Access Point LED PWR SYS LAN State Description Solid Green The unit is receiving DC power that is within the normal operating range. Off The power supply is not receiving power from either the AC/DC power adapter or a PoE+ Ethernet switch. Solid Amber The access point is loading its firmware or there is a system fault. Off The unit is operating normally. Solid Green The Ethernet port is operating at 1000 Mbps. Flashing Green The Ethernet port is operating at 1000 Mbps with link activity. Solid Amber The Ethernet port is operating at 10/100 Mbps. Flashing Amber The Ethernet port is operating at 10/100 Mbps with link activity. 2.4GHz Solid Green The 2.4GHz radio is sending and receiving radio waves. 5GHz Solid Green The 5GHz radio is sending and receiving radio waves. 21 Chapter 1: Overview Reset Button The Reset button on the rear panel is used to reboot the unit. The Reset button is recessed to prevent it from being accidentally pressed. To press the button, use a pointed object, such as the end of a straightened paper clip. 22 Chapter 2 Installing the Access Point This chapter describes how to install the AT-AP500 Wireless Access Point. This chapter contains the following sections: “Reviewing Safety Precautions” on page 24 “Unpacking the AT-AP500 Access Point” on page 26 “Installing the Access Point on a Wall or Ceiling” on page 27 “Kensington Lock” on page 34 “Starting the Initial Management Session on the Access Point” on page 35 23 Chapter 2: Installing the Access Point Reviewing Safety Precautions Please review the following safety precautions before you begin to install the access point. Note The indicates that a translation of the safety statement is available in a PDF document titled Translated Safety Statements on the Allied Telesis website at www.alliedtelesis.com/support. Warning To prevent electric shock, do not remove the cover. No userserviceable parts inside. This unit contains hazardous voltages and should only be opened by a trained and qualified technician. To avoid the possibility of electric shock, disconnect electric power to the product before connecting or disconnecting the LAN cables. E1 Warning Do not work on equipment or cables during periods of lightning activity. E2 Warning Power cord is used as a disconnection device. To de-energize equipment, disconnect the power cord. E3 Note Pluggable Equipment. The socket outlet shall be installed near the equipment and shall be easily accessible. E5 Caution Air vents must not be blocked and must have free access to the room ambient air for cooling. E6 24 AT-AP500 Wireless Access Point Installation Guide Warning Operating Temperature. This product is designed for a maximum ambient temperature of 40°C E7. Warning To reduce the risk of electric shock, the PoE port on this product must not connect to cabling that is routed outside the building where this device is located. E40 Caution FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. E80 Warning This equipment is intended for indoor use only. E95 Note All Countries: Install product in accordance with local and National Electrical Codes. E8 Note This product is not approved for use in a computer room as defined in the Standard for Protection of Electronic Computer/Data Processing Equipment, ANSI/NFPA 75. Note If you are not using PoE to power to unit, use only an approved AC/ DC adapter. Note You should verify that your PoE network adheres to the standards of a separated extra-low voltage (SELV) circuit before using the PoE feature on the wireless access point. 25 Chapter 2: Installing the Access Point Unpacking the AT-AP500 Access Point As you unpack the access point, check the shipping container for the components the following items: One AT-AP500 Wireless Access Point One AT-AP500 Wireless Access Point Quick Installation Guide One mounting-bracket screw One bracket and one base plate for wall or ceiling mounting If any item is missing or damaged, contact your Allied Telesis sales representative for assistance. If you are not using the PoE feature on the LAN port of the access point to power the device, you need to separately order the AT-TQ0091 AC/DC Power Adapter. The adapter comes with four regional AC plugs. (One of the AC plugs comes pre-installed on the adapter.) Refer to Figure 2. Figure 2. AT-TQ0091 AC/DC Power Adapter Go to “Installing the Access Point on a Wall or Ceiling” on page 27. 26 AT-AP500 Wireless Access Point Installation Guide Installing the Access Point on a Wall or Ceiling This procedure contains the following sections. Guidelines “Guidelines” “Mounting the Base Plate to the Wall or Ceiling” on page 28 “Attaching the Mounting Bracket to the Access Point” on page 29 “Attaching the Access Point to the Base Plate” on page 30 “Cabling the Access Point” on page 31 Please review the following guidelines before installing the access point on a wall or ceiling: The selected location must not block the ventilation slots around the base of the unit. Refer to Figure 3. Ventilation Slots Figure 3. Ventilation Slots The wall or ceiling mounting surface must be of proper material to accommodate the self-tapping screws, such as wood strong enough to support the weight of the equipment and cables. Otherwise, you must provide anchors to fit the mounting surface. One mounting-bracket screw is provided for attaching the mounting bracket to the unit. You must provide the four selftapping screws that secure the base plate to the wall or ceiling. The location must have an AC power source if you are using the AT-TQ0091 Power Adapter. 27 Chapter 2: Installing the Access Point Mounting the Base Plate to the Wall or Ceiling To mount the base plate to the wall or ceiling, perform the following: 1. Using the base plate as a template, mark the four holes for mounting the base plate to the wall or ceiling. See Figure 4 for hole dimensions. Figure 4. Base Plate Hole Dimensions 2. Drill the holes for the four self-tapping screws, and if applicable, two wall anchors. 3. If you are not installing wall anchors, skip to Step 4. If so, install the wall anchors. 4. Mount the base plate to the wall or ceiling using the self-tapping screws, as shown in Figure 5. Figure 5. Mounting Base Plate 28 AT-AP500 Wireless Access Point Installation Guide Attaching the Mounting Bracket to the Access Point To attach the mounting bracket to the access point, perform the following: 1. Place the access point upside down on a flat surface. 2. Place the bracket against the bottom of the access point and use the bracket to push downward on the stopper nub (see Figure 6). Figure 6. Bottom of Access Point 3. Turn the bracket in the direction of the arrows shown in Figure 7 until the two hooks hold the bracket: The stopper nub pops up, and the bracket locks in place. Figure 7. Locking Bracket to Access Point 4. Attach the mounting-bracket screw through the notch in the mounting bracket to the access point, as shown in Figure 8 on page 30: The bracket is fastened to the access point. 29 Chapter 2: Installing the Access Point Figure 8. Attaching the Mounting-Bracket Screw Attaching the Access Point to the Base Plate To attach the access point and mounting bracket to the base plate on the wall or ceiling, perform the following: 1. Have someone hold the bottom of the access point next to the base plate attached to the wall or ceiling. 2. Insert the two base-plate pins into the circles of the keyhole slots, as shown in Figure 9. Step 4 Step 2 Step 3 Step 3 Figure 9. Attaching Access Point to Base Plate 3. Slide the access point downward to lock the necks of the base-plate pins in the slots, as shown in Figure 9. 30 AT-AP500 Wireless Access Point Installation Guide 4. Fasten the access point to the base plate by turning the base-plate captive screw clockwise using a Phillips-head screwdriver, as shown in Figure 9 on page 30. Cabling the Access Point To install cabling on the access point, perform the following: 1. Connect a network cable to the LAN port (labeled WAN/PoE) on the rear panel of the access point. Refer to Figure 10. The specifications of the cable are listed in Table 2 on page 20. Figure 10. Connecting the Network Cable 2. If you have not already done so, connect the other end of the network cable to a port on an Ethernet switch. 3. Do one of the following: If the access point is to be powered with the AT-TQ0091 AC/DC Power Adapter, continue with this procedure to attach the power adapter. If the access point is to be powered with the PoE feature on the LAN Port, the installation procedure is complete. Go to “Kensington Lock” on page 34 or “Starting the Initial Management Session on the Access Point” on page 35. 4. Connect the DC power cable from the AT-TQ0091 AC/DC Power Adapter to the DC 12V connector on the rear panel of the access point. Refer to Figure 11 on page 32. 31 Chapter 2: Installing the Access Point Figure 11. Connecting the Power Cable from the AT-TQ0091 AC/DC Adapter 5. Check the AC plug on the AC/DC Power Adapter to see if it is the correct plug for your region. If it is not the correct plug, remove it by pushing down on the release tab and sliding it from the slot on the adapter. Refer to Figure 12. Release Tab Figure 12. Removing an AC Plug from the AT-TQ0091 AC/DC Power Adapter 32 AT-AP500 Wireless Access Point Installation Guide 6. Slide the correct AC plug for your region into the slot on the adapter until it clicks into place. Refer to Figure 13. Figure 13. Installing an AC Plug on the AT-TQ0091 AC/DC Power Adapter 7. Connect the AC plug on the power cord to an appropriate AC power source. Refer to Table 7 on page 38 for the power specifications of the power adapter. After installing the access point on a wall or ceiling, go to “Kensington Lock” on page 34 or “Starting the Initial Management Session on the Access Point” on page 35. 33 Chapter 2: Installing the Access Point Kensington Lock A Kensington lock can be used to secure the device. The lock is located on the rear panel (see Figure 14.) Kensington Lock Figure 14. Kensington Lock 34 AT-AP500 Wireless Access Point Installation Guide Starting the Initial Management Session on the Access Point This procedure contains the following sections. Requirements “Requirements” “Starting the Management Session” You must have the following to initiate a management session on the access point: Network with a DHCP server and a route for the access point to the Internet. When you power on the access point for the first time, it will obtain an IP address from the DHCP server, and then it must be able to access the Internet to register itself with the AlliedView Cloud service. Starting the Management Session Serial number for the access point. To start the initial management session on the access point, perform the following. 1. Create an AlliedView Cloud account at avcloud.alliedtelesis.com for the management of the access points. Refer to the AlliedView Cloud User’s Guide. Note This account will share the login credentials with the Allied Telesis Support portal account. 2. Add one or more access points to the account by entering the access point name and serial number. Refer to the AlliedView Cloud User’s Guide. 3. If not done already, power on the access point: the access point automatically registers with the AlliedView Cloud once a name and serial number is assigned, and the unit is powered up. 4. Refer to the AlliedView Cloud User’s Guide to add the access point to the network and configure the access point. 35 Chapter 2: Installing the Access Point 36 Appendix A Technical Specifications This appendix contains the following sections: “Physical Specifications” “Environmental Specifications” “Power Specifications” on page 38 “LAN Port” on page 39 “Safety and Electromagnetic Emissions Certifications” on page 41 Physical Specifications Table 4. AT-AP500 Physical Specifications Dimensions (W x D x H) 170.0 mm x 170.0 mm x 35.0 mm (6.7 in. x 6.7 in. x 1.4 in.) Weight 0.47 kg (1 lb.) Environmental Specifications Table 5. Environmental Specifications Operating Temperature of the Access Point When Using PoE 0° C to 40° C (32° F to 104° F) Operating Temperature of the Access Point When Using the AC/ DC Adapter 0° C to 40° C (32° F to 104° F) Storage Temperature -20° C to 60° C (-4° F to 140° F) Operating Humidity 5% to 80% non-condensing Storage Humidity 5% to 95% non-condensing 37 Appendix A: Technical Specifications Power Specifications Table 6. AT-AP500 Maximum Power Consumption AT-AP500 16 watts Table 7. AT-TQ0091 Power Adapter Input Range 100~240 Vac Input Frequency 47-63 Hz Input Power Consumption (no load) <0.3W max. 38 Output Voltage +12 VDC Output Current 2A max. AT-AP500 Wireless Access Point Installation Guide LAN Port Table 8. LAN Port Specifications Connector RJ45 Standards IEEE 802.3 (10Base-T) IEEE 802.3u (100Base-TX) IEEE 802.3ab (1000Base-T) PoE standard IEEE 802.3at (class 4) Figure 15 illustrates the pin layout of the LAN port. Figure 15. Pin Layout for the RJ45 Connector on the LAN Port Table 9 lists the pin signals when the port is operating in the MDI configuration at 10 or 100 Mbps. Table 9. MDI Pin Signals (10Base-T or 100Base-TX) Pin Signal TX+ TX- RX+ RX- 39 Appendix A: Technical Specifications Table 10 lists the pin signals for the MDI-X configuration at 10 or 100 Mbps. Table 10. MDI-X Pin Signals (10Base-T or 100Base-TX) Pin Signal RX+ RX- TX+ TX- Table 11 lists the pin signals when the LAN port is operating at 1000 Mbps. Table 11. 1000Base-T Connector Pinouts Pin 40 Pair Signal TX and RX TX and RX- TX and RX+ TX and RX+ TX and RX- TX and RX- TX and RX+ TX and RX- AT-AP500 Wireless Access Point Installation Guide Safety and Electromagnetic Emissions Certifications Table 12. Safety and Electromagnetic Emissions Certificates Electromagnetic FCC Class B Compatibility (EMC) ICES-003 Class B Radio Equipment FCC 47 CFR Part 15, Subpart C FCC 47 CFR Part 15, Subpart E FCC OET Bulletin No. 65 Supplement C RSS-Gen, Issue No. 4 RSS-247, Issue No. 1 Safety UL 60950-1 2nd Edition CAN/CSA C22.2 No. 60950-1 41 Appendix A: Technical Specifications 42 Appendix B Regulatory Statements This appendix contains the following regulatory statement: "Federal Communication Commission Interference Statement" on page 44 “Industry Canadal Statement” on page 45 43 Appendix B: Regulatory Statements Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. E80 Caution Avertissement de la FCC: Les changements ou modifications non expressément approuvés par la partie responsable de la conformité pourraient annuler l'autorité de l'utilisateur à utiliser cet équipement. E80 This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. For operation within 5150-5250MHz / 5470-5725MHz frequency range, it is restricted to indoor environment.The band from 5600-5650MHz will be disabled by the software during the manufacturing and cannot be changed by the end user. This device meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules. Rdiaion Exposure Statement 44 This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 26cm between the radiator & your body. Review Draft 3-24-16 Appendix B: Regulatory Statements Industry Canada Statement This device complies with RSS-247 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme à la norme CNR-247 d'Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la Classe B est conforme à la norme NMB-003 du Canada. Caution: (i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; (ii) the maximum antenna gain permitted for devices in the bands 52505350 MHz and 5470-5725 MHz shall comply with the e.i.r.p. limit; and (iii) the maximum antenna gain permitted for devices in the band 57255825 MHz shall comply with the e.i.r.p. limits specified for point-to-point and non point-to-point operation as appropriate. (iv) Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 56505850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. Avertissement: Le guide d’utilisation des dispositifs pour réseaux locaux doit inclure des instructions précises sur les restrictions susmentionnées, notamment: (i) les dispositifs fonctionnant dans la bande 5 150-5 250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux; 45 Review Draft 3-24-16 (ii) le gain maximal d’antenne permis pour les dispositifs utilisant les bandes 5 250-5 350 MHz et 5 470-5 725 MHz doit se conformer à la limite de p.i.r.e.; (iii) le gain maximal d’antenne permis (pour les dispositifs utilisant la bande 5 725-5 825 MHz) doit se conformer à la limite de p.i.r.e. spécifiée pour l’exploitation point à point et non point à point, selon le cas. (iv) De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-àd., qu’ils ont la priorité) pour les bandes 5 250-5 350 MHz et 5 650-5 850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 26cm between the radiator & your body. Déclaration d'exposition aux radiations: Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 26cm de distance entre la source de rayonnement et votre corps. 46
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V2.3 (128-bit) User Access : Print, Copy, Extract Page Mode : UseOutlines XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39 Format : application/pdf Title : at002286a.book Creator : wshrank Create Date : 2016:02:01 10:48:08Z Creator Tool : FrameMaker 12.0.4 Modify Date : 2016:04:25 22:55:15+08:00 Metadata Date : 2016:04:25 22:55:15+08:00 Producer : Acrobat Distiller 9.0.0 (Windows) Document ID : uuid:cbad276d-22ff-41e7-8d6e-6f3255d26117 Instance ID : uuid:77266841-0b29-49c7-b5eb-d9a814b5452b Has XFA : No Page Count : 46 Language : en Author : wshrankEXIF Metadata provided by EXIF.tools