Araknis Networks AN700APOAC Araknis Networks Dual-Band Wireless-AC 1750 Outdoor Access Point User Manual 2

Araknis Networks Araknis Networks Dual-Band Wireless-AC 1750 Outdoor Access Point Users Manual 2

Contents

Users Manual-2.pdf

© 2017 Araknis Networks® 11Araknis Networks Outdoor Wireless Access PointQuick Start GuideStep 4: Bracket WeatherproofingUse gaskets that best fit cable diameterWeep hole plugs must be installed correctlyLeave bottom weep holes open for drainageTo ensure weatherproofing, insert gasket even if cable entrance is not used.Pull cables through BEFORE installing foam pieces to avoid tearing the foam.
12Araknis Networks Outdoor Wireless Access PointQuick Start GuideSupport: 866.838.5052 Foam block must be pushed to the back of the cable entrance with large holes facing connectors.Step 4: ConnectConnectionsAInstall Cable GasketBPoE+ Power Input SpecificationsIEEE 802.3at Compliant Power SourcePower Consumption:Typical: 18WPeak: 23WPoE+ In Data Port (No PoE)Remove the adhesive backing before installation.NOTE: Leave the white dust cover in the non-PoE Data Port in place unless the port is being used. Use pliers to remove the dust cover.
© 2017 Araknis Networks® 13Araknis Networks Outdoor Wireless Access PointQuick Start GuideStep 5: Secure
14Araknis Networks Outdoor Wireless Access PointQuick Start GuideSupport: 866.838.5052 Step 6: Verify5 GHz (Blue) – O: Radio disabled Solid: Radio enabled Blinking: Radio activity2.4 GHz (Blue) – O: Radio disabled Solid: Radio enabled Blinking: Radio activityLAN 2 (Blue) – O: No Ethernet link Solid: Ethernet link established Blinking: Ethernet link activityLAN 1 (Blue) – O: No Ethernet link Solid: Ethernet link established Blinking: Ethernet link activityPower (Blue) – O: No power to AP Blinking: AP booting Solid: AP ready5GHz2.4GHzLAN 2LAN 1Power
© 2017 Araknis Networks® 15Araknis Networks Outdoor Wireless Access PointQuick Start GuideENABLEDWeb Browser AccessMobileAppsAN-110-SW-R-81 2 3 4 5 6 7 81 GbpsLink/ActStep 7: Claim on OvrCOvrC gives you remote device management, real-time notifications, and intuitive customer management, right from your computer or mobile device. Setup is plug-and-play, with no port forwarding or DDNS address required. To add this device to your OvrC account:Connect the WAP to the Internet.Log Into OvrC (www.ovrc.com) and create a or select a location to add the device.Add the Device (MAC address and Service Tag numbers needed for authentication)ABCInternetOvrC Server
16Araknis Networks Outdoor Wireless Access PointQuick Start GuideSupport: 866.838.5052 Step 8: Log Into Web InterfaceNOTE: If you can’t connect to the WAP using this method, or need to configure the device before connecting it to the network, try these options for accessing your device:• DHCP IP address – Page 18• Default IP Address – Page 19Find the WAP in the OvrC device list, then click Web Connect.Select whether you are on the LAN (I Am Local) or connecting over the Internet (I Am Remote).Log in using the default credentials:Username araknisPassword araknisABC
© 2017 Araknis Networks® 17Araknis Networks Outdoor Wireless Access PointQuick Start GuidePro Tip: Save and Apply ChangesAfter making changes to settings on a menu page, left-click the Save button on the menu to hold the new settings in the Apply Changes field.After all desired changes have been made, left-click Apply Changes to review the new settings. Left-click Apply to make the changes or Revert to cancel the changes.NOTE: Settings will take aect after the progress bar completes 100%.
18Araknis Networks Outdoor Wireless Access PointQuick Start GuideSupport: 866.838.5052 Other Access Methods: DHCP IP AddressThe WAP is configured to DHCP by default so that the DHCP server can assign an IP address when the WAP is connected to the network (the DHCP server is usually the router). This address can be used for accessing the web interface.Use one of these methods to find the IP address of the WAP:• Check the client table on your router• Use a network scanner (e.g. Fing) to sni the network. The Araknis WAP manufacturer field will display “Snap AV”See the highlighted field in the Fing screenshot to the right for an example of an Araknis device being identified.
© 2017 Araknis Networks® 19Araknis Networks Outdoor Wireless Access PointQuick Start GuideOther Access Methods: Default IP AddressIf the WAP is not issued an IP address on the network, or needs to be accessed while not connected to a network, you can configure your computer's network connection to allow access using the default IP address, 192.168.20.253.Connect your PC to the WAP using a network patch cable.On your PC, open the Control Panel and left-click Network and Internet.Left-click Network and Sharing Center.A B CWindows 7 screenshots shown for reference.Computer WAP
20Araknis Networks Outdoor Wireless Access PointQuick Start GuideSupport: 866.838.5052 Other Access Methods: Default IP AddressWindows 7 screenshots shown for reference.D E FIn the left bar, left-click Change adapter settings.Right-click the icon for the wired network connection and left-click Properties.Left-click to highlight Internet Protocol Version 4 (TCP/IPv4), then left-click Properties.
© 2017 Araknis Networks® 21Araknis Networks Outdoor Wireless Access PointQuick Start GuideOther Access Methods: Default IP AddressG H ILeft-click OK to close Internet Protocol Version 4 (TCP/IPv4) Properties, then left-click OK to close wireless network connection properties.In the General tab, left-click Use the following IP address: and enter the IP address and subnet mask.IP Address 192.168.20.2Subnet Mask 255.255.255.0Open a browser and navigate to the IP address, 192.168.20.253. Log in using the default credentials:Username araknisPassword araknisWindows 7 screenshots shown for reference.
22Araknis Networks Outdoor Wireless Access PointQuick Start GuideSupport: 866.838.5052 Troubleshooting: Reboot and Default ProceduresReset ButtonReboot – Press and release the RESET button. The device will reboot and no settings will be changed.Factory Default – Press and hold the RESET button for at least 15 seconds. The device will reset to factory defaults, then reboot.
Contacting Technical Support (866) 838-5052 techsupport@araknisnetworks.com2-Year Limited WarrantyAraknis Networks® products have a 2-Year Limited Warranty. This warranty includes parts and labor repairs on all components found to be defective in material or workmanship under normal conditions of use. This warranty shall not apply to products that have been abused, modified, or disassembled. Products to be repaired under this warranty must be returned to SnapAV or a designated service center with prior notification and an assigned return authorization (RA) number.© 2017 Araknis Networks® 170628-1130

Navigation menu