Araknis Networks AN700APOAC Araknis Networks Dual-Band Wireless-AC 1750 Outdoor Access Point User Manual 2
Araknis Networks Araknis Networks Dual-Band Wireless-AC 1750 Outdoor Access Point Users Manual 2
Contents
- 1. Users Manual-1_rev.pdf
- 2. Users Manual-2.pdf
Users Manual-2.pdf
Araknis Networks Outdoor Wireless Access Point Quick Start Guide Step 4: Bracket Weatherproofing Weep hole plugs must be installed correctly Pull cables through BEFORE installing foam pieces to avoid tearing the foam. Use gaskets that best fit cable diameter Leave bottom weep holes open for drainage To ensure weatherproofing, insert gasket even if cable entrance is not used. © 2017 Araknis Networks® 11 Araknis Networks Outdoor Wireless Access Point Quick Start Guide Step 4: Connect PoE+ In Connections Install Cable Gasket Data Port (No PoE) Foam block must be pushed to the back of the cable entrance with large holes facing connectors. PoE+ Power Input Specifications IEEE 802.3at Compliant Power Source Power Consumption: Remove the adhesive backing before installation. Typical: 18W Peak: 23W NOTE: Leave the white dust cover in the non-PoE Data Port in place unless the port is being used. Use pliers to remove the dust cover. 12 Support: 866.838.5052 Araknis Networks Outdoor Wireless Access Point Quick Start Guide Step 5: Secure © 2017 Araknis Networks® 13 Araknis Networks Outdoor Wireless Access Point Quick Start Guide Step 6: Verify 5 GHz (Blue) – Off: Radio disabled Solid: Radio enabled Blinking: Radio activity 2.4 GHz (Blue) – Off: Radio disabled Solid: Radio enabled Blinking: Radio activity LAN 2 (Blue) – Off: No Ethernet link Solid: Ethernet link established Blinking: Ethernet link activity LAN 1 (Blue) – Off: No Ethernet link Solid: Ethernet link established Blinking: Ethernet link activity Power (Blue) – Off: No power to AP Blinking: AP booting Solid: AP ready 14 5GHz 2.4GHz LAN 2 LAN 1 Power Support: 866.838.5052 Araknis Networks Outdoor Wireless Access Point Quick Start Guide Step 7: Claim on OvrC OvrC gives you remote device management, real-time notifications, and intuitive customer management, right from your computer or mobile device. Setup is plug-and-play, with no port forwarding or DDNS address required. To add this device to your OvrC account: A Connect the WAP to the Internet. B Log Into OvrC (www.ovrc.com) and create a or select a location to add the device. C Add the Device (MAC address and Service Tag numbers needed for authentication) Web Browser Access Internet 1 Gbps Link/Act ENABLED AN-110-SW-R-8 Mobile Apps OvrC Server © 2017 Araknis Networks® 15 Araknis Networks Outdoor Wireless Access Point Quick Start Guide Step 8: Log Into Web Interface A Find the WAP in the OvrC device list, then click Web Connect. B Select whether you are on the LAN (I Am Local) or connecting over the Internet (I Am Remote). C Log in using the default credentials: Username araknis Password araknis NOTE: If you can’t connect to the WAP using this method, or need to configure the device before connecting it to the network, try these options for accessing your device: 16 • DHCP IP address – Page 18 • Default IP Address – Page 19 Support: 866.838.5052 Araknis Networks Outdoor Wireless Access Point Quick Start Guide Pro Tip: Save and Apply Changes After making changes to settings on a menu page, left-click the Save button on the menu to hold the new settings in the Apply Changes field. After all desired changes have been made, left-click Apply Changes to review the new settings. Left-click Apply to make the changes or Revert to cancel the changes. NOTE: Settings will take affect after the progress bar completes 100%. © 2017 Araknis Networks® 17 Araknis Networks Outdoor Wireless Access Point Quick Start Guide Other Access Methods: DHCP IP Address The WAP is configured to DHCP by default so that the DHCP server can assign an IP address when the WAP is connected to the network (the DHCP server is usually the router). This address can be used for accessing the web interface. Use one of these methods to find the IP address of the WAP: • Check the client table on your router • Use a network scanner (e.g. Fing) to sniff the network. The Araknis WAP manufacturer field will display “Snap AV” See the highlighted field in the Fing screenshot to the right for an example of an Araknis device being identified. 18 Support: 866.838.5052 Araknis Networks Outdoor Wireless Access Point Quick Start Guide Other Access Methods: Default IP Address If the WAP is not issued an IP address on the network, or needs to be accessed while not connected to a network, you can configure your computer's network connection to allow access using the default IP address, 192.168.20.253. Windows 7 screenshots shown for reference. A Connect your PC to the WAP using a network patch cable. Computer © 2017 Araknis Networks® B On your PC, open the Control Panel and left-click Network and Internet. C Left-click Network and Sharing Center. WAP 19 Araknis Networks Outdoor Wireless Access Point Quick Start Guide Other Access Methods: Default IP Address Windows 7 screenshots shown for reference. D In the left bar, left-click Change adapter settings. 20 E Right-click the icon for the wired network connection and left-click Properties. F Left-click to highlight Internet Protocol Version 4 (TCP/IPv4), then left-click Properties. Support: 866.838.5052 Araknis Networks Outdoor Wireless Access Point Quick Start Guide Other Access Methods: Default IP Address Windows 7 screenshots shown for reference. G In the General tab, left-click Use the following IP address: and enter the IP address and subnet mask. H Left-click OK to close Internet Protocol Version 4 (TCP/IPv4) Properties, then left-click OK to close wireless network connection properties. Open a browser and navigate to the IP address, 192.168.20.253. Log in using the default credentials: IP Address 192.168.20.2 Username araknis Subnet Mask 255.255.255.0 Password araknis © 2017 Araknis Networks® 21 Araknis Networks Outdoor Wireless Access Point Quick Start Guide Troubleshooting: Reboot and Default Procedures Reset Button 22 Reboot – Press and release the RESET button. The device will reboot and no settings will be changed. Factory Default – Press and hold the RESET button for at least 15 seconds. The device will reset to factory defaults, then reboot. Support: 866.838.5052 Contacting Technical Support (866) 838-5052 techsupport@araknisnetworks.com 2-Year Limited Warranty Araknis Networks® products have a 2-Year Limited Warranty. This warranty includes parts and labor repairs on all components found to be defective in material or workmanship under normal conditions of use. This warranty shall not apply to products that have been abused, modified, or disassembled. Products to be repaired under this warranty must be returned to SnapAV or a designated service center with prior notification and an assigned return authorization (RA) number. © 2017 Araknis Networks® 170628-1130
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.7 Linearized : Yes Encryption : Standard V2.3 (128-bit) User Access : Print, Extract Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39 Modify Date : 2017:07:05 10:48:46+08:00 Create Date : 2017:07:05 10:47:27+08:00 Metadata Date : 2017:07:05 10:48:46+08:00 Creator Tool : Adobe InDesign CC 2017 (Windows) Format : application/pdf Document ID : uuid:7c84252c-95b6-4552-9b42-7424fe627af9 Instance ID : uuid:2a455f94-72b5-43b8-a6fb-d9f4b0082a99 Producer : Adobe PDF Library 15.0 Page Count : 14 Creator : Adobe InDesign CC 2017 (Windows)EXIF Metadata provided by EXIF.tools