Arts Electronics LPP1000 TURNTABLE AUDIO SYSTEM User Manual 1
Arts Electronics Co., Ltd TURNTABLE AUDIO SYSTEM 1
Contents
user manual 1
ENGLISH FRANÇAIS
TURNTABLE AUDIO SYSTEM
OWNER'S MANUAL
MODE D’EMPLOI
LP-P1000
Z
77-20L100000000
LP-P1000_OM_EF_vA_CS6.indb 1 2013/09/11 16:16
2
IMPORTANT SAFETY PRECAUTIONS
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
M
The lightning flash with arrowhead in an equilateral
triangle is intended to alert the user to the presence of
uninsulated “dangerous voltage” within the product’s
enclosure that could be of sufficient magnitude to con-
stitute a risk of electric shock to persons.
V
The exclamation point in an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
CAUTION
oDO NOT REMOVE THE EXTERNAL CASES OR CABINETS TO EXPOSE
THE ELECTRONICS. NO USER SERVICEABLE PARTS ARE INSIDE.
oIF YOU ARE EXPERIENCING PROBLEMS WITH THIS PRODUCT,
CONTACT TEAC FOR A SERVICE REFERRAL. DO NOT USE THE
PRODUCT UNTIL IT HAS BEEN REPAIRED.
oUSE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY
RESULT IN HAZARDOUS RADIATION EXPOSURE.
IN USA/CANADA, USE ONLY ON 120 V SUPPLY.
LP-P1000_OM_EF_vA_CS6.indb 2 2013/09/11 16:16
3
This product contains a semiconductor laser system inside the cabi-
net and is classified as a “CLASS 1 LASER PRODUCT”.
To prevent being exposed to the laser beam, do not try to open the
enclosure.
Laser:
Type: EP-C101
Manufacturer: Ever Bright Teachnolog and Science
Electronical Co., LTD.
Laser output: Less than 0.5 mW
Wavelength: 790±25 nm
Model for USA
This product has been designed and manufactured according to
FDA regulations “title 21, CFR, chapter 1, subchapter J, based on the
Radiation Control for Health and Safety Act of 1968”, and is classified
as class laser product. There is not hazardous invisible laser radia-
tion during operation because invisible laser radiation emitted
inside of this product is completely confined in the protective
housings.
The label required in this regulation is as follows:
Q Precautions concerning batteries
Misuse of batteries could cause them to rupture or leak leading
to fire, injury or the staining of nearby things. Please read and
observe the following precautions carefully.
oBe sure to insert the batteries with correct positive (+) and
negative (_) orientations.
oUse batteries of the same type. Never use different types of
batteries together.
oIf the remote control is not used for a long time (more than a
month), remove the batteries to prevent them from leaking.
oIf the batteries leak, wipe away the leakage inside the battery
compartment and replace the batteries with new ones.
oDo not use batteries of types other than those specified. Do
not mix new batteries with old ones or use different types of
batteries together.
oDo not heat or disassemble batteries. Never throw batteries
into fire or water.
oDo not carry or store batteries with other metallic objects.
The batteries could short circuit, leak or explode.
oNever recharge a battery unless it is confirmed to be a
rechargeable type.
LP-P1000_OM_EF_vA_CS6.indb 3 2013/09/11 16:16
4
IMPORTANT SAFETY INSTRUCTIONS
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with
the manufacturer's instructions.
8) Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-
type plug. A polarized plug has two blades with one wider than
the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are pro-
vided for your safety. If the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete
outlet.
10) Protect the power cord from being walked on or pinched par-
ticularly at plugs, convenience receptacles, and the point where
they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod,
bracket, or table specified by the manu-
facturer, or sold with the apparatus. When
a cart is used, use caution when moving
the cart/apparatus combination to avoid
injury from tip-over.
13) Unplug this apparatus during lightning
storms or when unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate normally,
or has been dropped.
oThe apparatus draws nominal non-operating power from the
AC outlet with its POWER or STANDBY/ON switch not in the ON
position.
oThe mains plug is used as the disconnect device, the disconnect
device shall remain readily operable.
oCaution should be taken when using earphones or headphones
with the product because excessive sound pressure (volume)
from earphones or headphones can cause hearing loss.
CAUTION
oDo not expose this apparatus to drips or splashes.
oDo not place any objects filled with liquids, such as vases, on
the apparatus.
oDo not install this apparatus in a confined space such as a
book case or similar unit.
oThe apparatus should be located close enough to the AC
outlet so that you can easily reach the power cord plug at any
time.
oIf the product uses batteries (including a battery pack or
installed batteries), they should not be exposed to sunshine,
fire or excessive heat.
oCAUTION for products that use replaceable lithium batter-
ies: there is danger of explosion if a battery is replaced with
an incorrect type of battery. Replace only with the same or
equivalent type.
The Bluetooth® word mark and logos are registered trademarks
owned by Bluetooth SIG, Inc. and any use of such marks by TEAC is
under license.
This product is protected by certain intellectual property rights of
Microsoft. Use or distribution of such technology outside of this
product is prohibited without a license from Microsoft.
MPEG Layer-3 audio coding technology licensed from Fraunhofer IIS
and Thomson.
Other company names and product names in this document are
the trademarks or registered trademarks of their respective owners.
LP-P1000_OM_EF_vA_CS6.indb 4 2013/09/11 16:16
CAUTION
Changes or modifications not expressly approved by
the party responsible for compliance could void the
user’s authority to operate the equipment.
CAUTION
Authorization of wireless devices are different in coun-
tries or regions. Please use only in the country where
you purchased the product.
oDepending on the country, restrictions on the use
of Bluetooth wireless technology might exist.
Confirm the laws and regulations of the country or
region where you want to use the unit before use.
Radiation Exposure requirements
This equipment meets the regulation, which is recog-
nized internationally, for the case of human exposure to
radio waves generated by the transmitter.
Based on the following two conditions:
oEnd-users and installers must be provided with
antenna installation instructions and transmit-
ter operating conditions for satisfying RF exposure
compliance.
oThis equipment should be installed and operated
with minimum distance 20 cm (8") between the
radiator and your body.
Statement of compliance
Model for USA
This device complies with FCC radiation exposure lim-
its set forth for an uncontrolled environment.
Model for Canada
The device meets the exemption from the routine
evaluation limits in section 2.5 of RSS 102 and com-
pliance with RSS-102 RF exposure, users can obtain
Canadian information on RF exposure and compliance.
Compliance of radio transmitter and
interference
Model for USA
This device complies with Part.15 of FCC Rules.
Operation is subject to the following two conditions:
1) This device may not cause interference, and
2) This device must accept any interference, including
interference that may cause undesired operation.
Labeling of authorization
FCC ID: TZI-LPP1000
Model for Canada
Compliance of radio transmitter
This device complies with Industry Canada licence-
exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not
cause interference, and (2) this device must accept any
interference, including interference that may cause
undesired operation of the device.
Labeling of authorization
IC: 7234A-LPP1000
5
ENGLISH
Wireless equipment precautions (1)
LP-P1000_OM_EF_vA_CS6.indb 5 2013/09/11 16:16
Information for interference
(FCC requirements)
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interfer-
ence in a residential installation.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will
not occur in a particular installation.
If this equipment does cause harmful interference to
radio or television reception, which can be deter-
mined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or
more of the following measures.
oReorient or relocate the equipment and/or the
receiving antenna.
oIncrease the separation between the equipment and
receiver.
oConnect the equipment into an outlet on a cir-
cuit different from that to which the receiver is
connected.
oConsult the dealer or an experienced radio/TV tech-
nician for help.
6
Wireless equipment precautions (2) Bluetooth® notes
When using this unit with a mobile phone or other
Bluetooth devices, they should be no more than about
10 m (33 ft) apart. Depending on the circumstances of
use, however, the effective transmission distance might
be shorter.
Wireless communication with every device that sup-
ports Bluetooth wireless technology is not guaranteed.
To determine the compatibility between this unit
and another device that supports Bluetooth wireless
technology, refer to that device's operation manual or
contact the shop where you purchased it.
LP-P1000_OM_EF_vA_CS6.indb 6 2013/09/11 16:16
7
ENGLISH
LP-P1000_OM_EF_vA_CS6.indb 7 2013/09/11 16:16
8
Before useContents
Included items
Check to be sure the box includes all the supplied
accessories shown below.
Please contact the store where you purchased this unit
if any of these accessories are missing or have been
damaged during transportation.
Speakers × 1 pair
Remote control (RC-1312) × 1
45 RPM adapter × 1
Sapphire stylus for LP and EP records (already
installed)
Protective rubber mat for turntable × 1
Turntable cover × 1
Hinges × 2
Batteries for remote control (AA) × 2
AM antenna × 1
FM antenna (wire type) × 1
Stereo mini plug cable (60 cm or 24") × 1
Speaker cable (3 m or 10 ft) × 2
Owner’s manual (this document) × 1
oKeep this manual in a safe place for future reference.
Warranty card × 1
Wireless equipment precautions ......................5
Bluetooth® notes .....................................6
Before use ............................................8
Discs ................................................10
MP3/WMA files ......................................12
Handling records ....................................13
Connections .........................................14
Replacing the stylus .................................17
Names and functions of parts (main unit) ............18
Names and functions of parts (remote control) .......20
Using the remote control ............................22
Names and functions of parts (turntable) ............23
Turntable cover ......................................24
Setting the clock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Basic operation ......................................27
Listening to a CD ....................................30
Programmed playback ...............................34
Repeat and shuffle playback .........................38
About MP3/WMA files ...............................39
Listening to audio from a Bluetooth device ..........42
Pairing with another Bluetooth device ...............44
Listening to records. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Listening to the radio ................................48
Preset tuning ........................................50
Wakeup timer .......................................52
Sleep timer ..........................................55
Listening to a connected device .....................56
Troubleshooting .....................................57
Specifications ........................................59
Thank you for choosing TEAC. Read this manual care-
fully to get the best performance from this unit.
LP-P1000_OM_EF_vA_CS6.indb 8 2013/09/11 16:16
9
ENGLISH
Precautions for use
oDo not place anything on the turntable cover.
Objects on the cover might cause noise due to vibra-
tions or fall off, especially during playback.
oAvoid placing the unit in direct sunlight, close to
a source of heat or in other similar conditions. Do
not place the unit on top of an amplifier or other
equipment that might generate heat that exceeds
the operating temperature range of this unit.
Doing so could cause discoloration, deformation or
malfunction.
oAs the unit could become warm during operation,
always leave sufficient space around it for ventila-
tion. When installing this unit, leave at least 20 cm
(8") between it and walls. To allow good heat dis-
sipation, leave a little space between it and other
devices. When placing it in a rack, for example, leave
at least 40 cm (16") open above it and 10 cm (4")
open behind it. Failure to provide these gaps could
cause heat to build up inside and result in fire.
oDO NOT MOVE THE UNIT DURING PLAYBACK. During
playback, the disc or the record rotates. Do not lift or
move the unit during playback. Doing so may dam-
age the disc, the record, the stylus, the cartridge or
the unit.
oAlways remove the disc or the record before relocat-
ing or moving this unit. Moving the unit with a disc
inside or a record on the turntable could damage the
disc, the record, the stylus and the cartridge or could
cause a malfunction.
oThe voltage supplied to the unit should match the
voltage as printed on the rear panel. If you are in any
doubt regarding this matter, consult an electrician.
oDo not open the cabinet as this might result in dam-
age to the circuitry or electrical shock. If a foreign
object should get into the unit, contact your dealer
or TEAC customer support.
oWhen removing the power plug from the wall outlet,
always pull directly on the plug, never yank on the
cord.
oWhen a TV is on, depending on the TV broadcast
electromagnetic wave conditions, lines might appear
on the TV screen if the unit is turned on. This is not a
malfunction of the unit or the TV. If this occurs, put
this unit into standby mode (off) when using the TV.
User registration
Customers in the USA, please visit the TEAC website
(http://audio.teac.com/support/registration/) to register
as a user online.
Maintenance
If the surface of the unit gets dirty, wipe it with a soft
cloth or use diluted mild liquid soap. Allow the surface
of the unit to dry completely before using.
Do not use chemical cleaning cloths, thinner or similar
substances as they could damage the surface of the
unit.
VCAUTION
For safety, disconnect the power cord from
the socket before cleaning.
LP-P1000_OM_EF_vA_CS6.indb 9 2013/09/11 16:16
10
CD-R/CD-RW discs
This unit can play back CD-R and CD-RW discs that have
been recorded in the audio CD format (CD-DA) and the
MP3 or WMA format.
oDiscs created by a CD recorder must be finalized with
the CD recorder that was used to create the discs
before being used with this unit.
oDepending on disc quality and recording conditions,
playback of some discs might not be possible. Please
see the manual for the device that you used to create
the disc.
oIf you are uncertain about the handling of a CD-R
or CD-RW disc, please contact the seller of the disc
directly.
Precautions for use
oDo not use cracked discs because they could dam-
age the unit.
oWhen writing something on the label side of a disc,
use a felt tip permanent marker. The use of a ball-
point pen or other pen with a hard tip could damage
the disc, making it unplayable.
oNever use commercially available CD stabilizers.
Doing so could make the disc unplayable or damage
the unit.
oNever use CDs with irregular shapes, including heart-
shaped and octagonal discs because such discs
could damage the unit.
Discs
Discs that can be played on this unit
CDs with the Compact disc Digital Audio logo
CD-R and CD-RW discs that have been created in
the audio CD format and finalized correctly.
CD-R and CD-RW discs that have been written
with MP3 or WMA files and finalized.
This unit can play the above types of discs (without
adapters). This unit cannot play any other types of discs.
VCAUTION
If you try to play any other type of disc with
this unit, loud noises that damage speakers
or harm hearing could occur. Never try to
play any other type of disc with this unit.
oThis unit might not be able to properly play back
Copy Control CDs, Dual Discs and other special CDs
that do not conform to the Red Book CD standard.
Operation and sound quality cannot be guaranteed
when special discs are used in this unit. If playback of
a special disc should cause trouble, contact the seller
of the disc.
LP-P1000_OM_EF_vA_CS6.indb 10 2013/09/11 16:16
11
ENGLISH
Handling precautions
oAlways insert the disc into the disc tray with the label
side up. Only one side of a Compact Disc can be
played or used for recording.
oIf the side of the disc that the signal is recorded on
(unlabeled side) has scratches, fingerprints or dirt on
it, for example, playback errors could occur. Please
handle discs with care.
oTo remove a disc from its case, press down on the
center of the case and hold the disc by its edges.
Do not touch the side of the disc that has the data
encoded on it (unlabeled side).
Removal from case Holding by edges
Storage precautions
oDiscs should be stored in their cases when not being
used. Failure to do so could result in warping and
scratches.
oDo not leave discs in places that are exposed to direct
sunlight or that are very humid or hot. Long exposure
to such conditions could warp or degrade discs, mak-
ing them unplayable.
oSince CD-R/CD-RW discs are more susceptible to the
effects of heat and ultraviolet rays compared to com-
mercial CDs, do not leave them for long periods of
time in places that are, for example, exposed to direct
sunlight or near equipment that generate heat.
oSmudges on a disc might cause the sound to skip or
degrade the sound quality. Always clean discs before
storing them.
Maintenance
oIf the side of the disc that has the data encoded on
it (unlabeled side) becomes dirty with fingerprints
or dust, use a soft cloth to wipe the surface from the
center directly toward the edge.
oNever use record cleaners, antistatic treatments,
thinners or similar chemicals to clean discs. Such
chemicals could harm the surface of the disc.
LP-P1000_OM_EF_vA_CS6.indb 11 2013/09/11 16:16
12
MP3/WMA files
This unit can play MP3 and WMA files that are on CD-R/
CD-RW discs.
oAudio file formats that can be played back
MP3 (file extension: .mp3)
Bit rate: 8 kbps to 320 kbps
Sampling frequency: 16 kHz to 48 kHz
WMA (file extension: .wma)
Bit rate: 8 kbps to 320 kbps
Sampling frequency: 32 kHz, 44.1 kHz, 48 kHz
Note: Digital Rights Management (DRM) is not
supported.
oUp to 8 levels of folders supported
File information shown on the display
The display of this unit can only show single-byte
alphanumeric characters.
oIf the file information uses Japanese, Chinese or other
double-byte characters, playback is possible but the
name will not be shown correctly.
Precautions when creating MP3/WMA
files on a computer
oOnly discs that have been recorded using the ISO
9660 standard can be played by this unit.
oMP3 and WMA files are recognized by their file exten-
sions (“.mp3” for MP3 files and “.wma” for WMA files. )
Always include the extension in the file name.
oFiles without extensions cannot be recognized. A file
cannot be played back regardless of the file name
extension, if the data is not in the MP3 or WMA
format.
oAfter recording to a CD-R/CD-RW, always close the
session (complete disc creation). This unit cannot
play a disc if its session has not been closed.
oA maximum of 999 files and 99 folders on a disc can
be played. If the media has more than these maxi-
mums, this unit might not be able to correctly play
any file that is the 1000th or higher or any folder that
is the 100th or higher.
oDiscs made with multi-session recording are not sup-
ported. Only the first session can be played back.
oDepending on the condition of the disc, playback
might not be possible or the sound might skip.
oThis unit cannot play copyright-protected audio files.
LP-P1000_OM_EF_vA_CS6.indb 12 2013/09/11 16:16
13
ENGLISH
Handling records
Holding records
When holding a record or removing it from its sleeve,
avoid touching the grooves by holding the record by
its label and edge with one hand or by holding it by its
edge with both hands.
Label Grooves
Outer edge
Cleaning
oFingerprints and dust on a record can cause noise
and the sound to skip, as well as damage the record
itself and the stylus. Use a commercially available
record cleaner to clean records. Do not use thinner or
anything other than a record cleaner. Such chemicals
could harm the surface of the record.
oWhen using a record cleaner, wipe the surface of the
record in a circular motion, following the grooves.
Precautions
oDo not leave records in places that are exposed to
direct sunlight or are very hot or very humid. Leaving
a record in such a condition for a long time could
result in warping or other damage.
oDo not stack multiple records or place heavy objects
on top of them. Do not leave records at an angle for
long amounts of time either. Doing so could result in
warping or other damage.
oDo not allow hard objects to directly touch the audio
grooves. Doing so could cause scratches.
oAfter you finish playing a record, always put it back
into its sleeve for storage. Leaving a record unpro-
tected could result in warping or scratching.
oDo not use cracked records.
Placing the rubber mat
Place the included rubber mat, which protects the turn-
table, on the turntable.
oThe rubber mat has top and bottom sides. Place
the side with radiating lines face up as shown in the
illustration.
LP-P1000_OM_EF_vA_CS6.indb 13 2013/09/11 16:16
14
VPrecautions when making connections
oDo not turn the unit on until after making all connections.
oCarefully read the manuals of the devices that you are connecting
and follow their instructions when making connections.
BC
D
A
LLR
Connections (1)
A FM antenna connector
Extend the FM antenna and fix it in the position
where the reception is best (on a window frame or
wall, for example).
B AM antenna connector
Assemble the included AM loop antenna and con-
nect it to the AM antenna jack on the back of the
unit.
Place the antenna in the position that provides the
best AM reception.
Assembling the AM antenna
To assemble the AM antenna, turn the base in the direc-
tion of the arrow. Then, insert the hook at the bottom of
the loop into the slot in the base.
Antenna base Hook
1 2
Recording device
Cassette deck, CD recorder, etc.
Audio output
jacks
Audio input
jacks
LP-P1000_OM_EF_vA_CS6.indb 14 2013/09/11 16:16
15
ENGLISH
C Analog audio input and output jacks
(AUX1 IN/LINE OUT)
These input and output analog audio signals.
Use commercially available audio cables to connect
other equipment to the input and output jacks of
this unit.
White (L)
Red (R)
White (L)
Red (R)
oTo connect and use a cassette deck, CD recorder
or other recording device, connect that device’s
output jacks to this unit’s AUX 1 IN jacks, and that
device’s input jacks to this unit’s LINE OUT jacks.
oInsert the plugs completely. Do not bundle these
cords with power cords or speaker cables. Doing
so could reduce the audio quality or cause noise.
There are analog audio input jacks on both the front
and rear panels.
If cables are connected to both the front panel
(AUX 2 IN) and the rear panel (AUX 1 IN) jacks, the
audio input through the front panel jack (AUX 2 IN)
will be used. If nothing is connected to the front
panel jack (AUX 2 IN), the audio input through the
rear panel jack (AUX 1 IN) will be used.
D AC power cord
Confirm that the power plug is plugged into a
working outlet.
V Be sure to connect the power cord to an
AC outlet that supplies the correct voltage.
Connection to an outlet that supplies incor-
rect voltage could cause fire or electric shock.
Hold the power plug when plugging it into an
outlet or unplugging it. Never pull or yank on
the power cord. Unplug the power cord from
the outlet when you are not planning to use
the unit for an extended period of time.
LP-P1000_OM_EF_vA_CS6.indb 15 2013/09/11 16:16
16
Connecting the speakers
Use the included speaker cables to connect the
included speakers to the main unit.
Right speaker Left speaker
While pressing the lever, insert the end of the cable
(where the wire is exposed). Release the lever to con-
nect the speaker cable. Connect the cable to both the
main unit and the speaker.
Connections (2)
Connect the end of the + speaker cable with the mark
into the red speaker terminal.
Connect the end of the transparent − speaker cable
into the black speaker terminal.
oGently pull the cables to make sure they are con-
nected firmly.
oConfirm that only the exposed part of the wire is
inserted into the terminal and that the cable sheath
is not touching the terminal.
oA short could occur if the exposed core wire at the
tip of a speaker cable touches another cable or
terminal.
oNever let the speaker cables short.
oIn order to avoid noise, do not bundle speaker cables
with power cords or other cables.
The included speakers have bass ports in their backs.
Place the speakers so that these ports are not blocked
by, for example, other objects or walls.
Bass port
Speaker terminals
LP-P1000_OM_EF_vA_CS6.indb 16 2013/09/11 16:16
17
ENGLISH
Replacing the stylus
oRecord styluses are precision parts, so handle them
carefully to avoid bending or damaging their tips. If
a stylus becomes bent or damaged, it might not be
able to follow the audio groove precisely and could
damage records or cause other malfunction.
oIf a stylus becomes dirty, use a commercially avail-
able stylus cleaner or similar product to clean it.
oDo not rub the stylus tip forcefully with anything
hard. Do not wipe the stylus with thinner or other
chemicals. Doing so could harm it.
Replacing the stylus
Using a record stylus wears it down, which could cause
the sound quality to worsen and possibly damage
records. Replace the stylus with a replacement stylus
specified by TEAC as early as possible. In general, you
should replace a sapphire stylus for LP and EP records
after about 50 hours of use and a diamond stylus for SP
records after about every 100 hours.
CAUTION
oSince loud noises could suddenly occur, put the unit
into standby before changing the stylus.
oBe careful not to hurt your hand or the equipment.
oBe careful not to allow small children to accidentally
swallow styluses.
Removing the stylus (red part)
1 Press the STANDBY/ON button to put
the unit into standby.
2 Hold the cartridge with one hand, and
use a small screwdriver or other tool to
push the level difference at the front
of the stylus down in the “A” direction.
Then, pull it forward and o.
Screwdriver
Attaching a new stylus
1 Insert it in the “B” direction so that the
end of the stylus ts into the cartridge.
2 Push in the “C” direction until it snaps
into place.
Replacement styluses (sold separately)
STL-103: Sapphire stylus for LP and EP records
(3 per set)
SPL-102: Diamond stylus for SP records
(2 per set)
For replacement styluses, contact your dealer or
TEAC customer support (see the back cover).
LP-P1000_OM_EF_vA_CS6.indb 17 2013/09/11 16:16
18
Names and functions of parts (main unit)
K L M N O P
A B C D HE F G I J
A STANDBY/ON button
Press this button to turn the unit on or put it in
standby. The ring around the STANDBY/ON button
lights blue when on.
B Function buttons
(PHONO/AUX, FM/AM, CD/Bluetooth)
To listen to a record, press the PHONO/AUX button
and select PHONO.
To listen to an external device connected to one
of the AUX jacks (AUX 1 IN or AUX 2 IN), press the
PHONO/AUX button and select AUX.
To listen to a CD, press the CD/Bluetooth button
and select CD.
To listen to a Bluetooth device, press the CD/
Bluetooth button and select Bluetooth.
To listen to the radio, press the FM/AM button.
Press the FM/AM button again to switch between
FM and AM bands.
C PAIRING button
Use this when pairing with other Bluetooth devices
and when ending Bluetooth connections (pages
44 and 43).
D PLAY MODE button
FM MODE button
When listening to an CD/MP3/WMA file, use to
change the play mode (ordinary, repeat, shuffle)
(page 38).
When listening to FM radio, use to switch between
stereo and mono (page 49).
E Search (m/,) buttons
PRESET (j/k) buttons
Press and hold during CD playback to search for-
ward/backward (page 33).
When listening to the radio, use to select preset sta-
tions (page 51).
Q Q
LP-P1000_OM_EF_vA_CS6.indb 18 2013/09/11 16:16
19
ENGLISH
F Stop (8) button
Press to stop CD playback.
G Play/pause (y/9) button
Press when the CD or a supported Bluetooth device
is stopped or paused to start playback.
Use this button to pause playback during playback.
H Open/close button (-)
Press to open and close the disc tray.
I Turntable cover
J VOLUME knob
Use to adjust the volume. Turn right to raise the vol-
ume and left to lower it.
K PHONES jack
When you use headphones, first reduce the volume
level to minimum. Then, insert the plug from your
headphones into the PHONES jack, and turn the
volume up gradually by turning the VOLUME knob.
oDo not turn the unit on and put it into standby
or connect and disconnect the headphones plug
while wearing headphones.
(Doing so could cause loud noise to be output
from the headphones.)
oWhen a plug is in the headphones jack, no sound
will be output from the speakers.
L Analog audio input jack (AUX 2 IN)
Use to input analog audio signals.
To connect the headphones jack of a portable
music player or similar device to the unit, use the
included stereo mini plug cable to connect it to the
front panel analog audio input jack (AUX 2 IN). In
this case, adjust the volume on the portable music
player. Be careful, however, because turning the
volume of the portable music player up too much
could cause distortion.
M Remote control signal receiver
Signals sent from the remote control are received
here. When using a remote, point it toward this
spot.
N Display
This shows the track number, time, FM/AM fre-
quency and other information.
O Disc tray
P Scroll/skip knob
(MULTI JOG/. //j k)
Use when tuning the radio to select stations (page
49).
Use this also to set the current time and the wakeup
timer (pages 25 and 52).
When listening to a CD, use to skip to the previous
or next track (page 33).
Q Right/left speakers
Place the speakers as desired.
LP-P1000_OM_EF_vA_CS6.indb 19 2013/09/11 16:16
20
Names and functions of parts (remote control)
a
b
c
d
h
e
m
f
g
n
i
o
p
q
l
j
k
a STANDBY/ON button
b DIMMER button
Use to adjust the display brightness (page 29).
c TIMER button
Use to turn the wakeup timer on and off (page 52).
d SLEEP button
Use to set the sleep timer (page 55).
e PRESET/MP3 (j/k) buttons
When listening to the radio, use to select preset
radio stations (page 51).
When listening to an MP3/WMA disc, use to select
the folder number (page 34).
f TUNING/TIME (j/k) buttons
Skip/search (.m/,/) buttons
When listening to the radio, use for manual and
auto station tuning (page 49).
When listening to an MP3/WMA disc, use to select
file numbers (page 34).
When setting the clock and the wakeup timer, use
to set the time (pages 25 and 52).
When listening to a CD, use to skip to the previous
or next track. Press and hold during CD playback to
search forward/backward (page 33).
g Stop (8) button
Press to stop playback.
When both the main unit and the remote control
have buttons with the same functions, the instructions
in this manual refer to only one set of buttons, but the
other set of buttons can be used in the same way.
LP-P1000_OM_EF_vA_CS6.indb 20 2013/09/11 16:16
21
ENGLISH
h Play/pause (y/9) button
Press when stopped or paused to start playback.
Use this button to pause playback during playback
(page 32).
i Function buttons
(PHONO/AUX, FM/AM, CD/Bluetooth)
To listen to a record, press the PHONO/AUX button
and select PHONO.
To listen to an external device connected to one
of the AUX jacks (AUX 1 IN or AUX 2 IN), press the
PHONO/AUX button and select AUX.
To listen to the radio, press the FM/AM button. Press
the FM/AM button again to switch between FM and
AM bands.
To listen to a CD, press the CD/Bluetooth button
and select CD.
To listen to a Bluetooth device, press the CD/
Bluetooth button and select Bluetooth.
j SOUND button
Use to adjust the bass and treble, as well as the left-
right volume balance (page 28).
k MUTE button
Use to temporarily silence the output (page 29).
l PAIRING button
Use this when pairing with other Bluetooth devices
and when ending Bluetooth connections (pages
44 and 43).
m DISPLAY button
Press when FM/AM or CD/Bluetooth is selected to
show the current time.
n INFO button
When listening to a CD, use to change the informa-
tion shown on the display (page 40).
o MEMORY/CLOCK ADJ button
When listening to the radio, use when setting radio
station presets (page 50).
Use to adjust the clock (page 25).
p PLAY MODE/FM MODE button
When listening to a CD, use to change the play
mode (ordinary, repeat, shuffle) (page 38).
When listening to FM radio, use to switch between
stereo and mono (page 49).
q VOLUME (+/−) buttons
Use to adjust the volume. Press the + button to
raise the volume, and press the − button to lower
the volume.
LP-P1000_OM_EF_vA_CS6.indb 21 2013/09/11 16:16
22
Using the remote control
Precautions for use
oWhen using the remote control, point it toward the
remote control signal receiver on the main unit from
a distance of 5 m (16 ft) or less. Do not place obstruc-
tions between the main unit and the remote control.
oThe remote control might not work if the remote
control signal receiver on the main unit is exposed to
sunlight or bright lights. In this case, try moving the
main unit.
oBeware that use of this remote control could cause
the unintentional operation of other devices that can
be controlled by infrared rays.
Installing batteries
Remove the cover from the back of the remote control.
Insert 2 AA batteries into the compartment according
to the +/− indications. Then, close the cover.
When to replace batteries
If the distance required between the remote and main
unit decreases or if the unit stops responding to the
remote buttons, replace both batteries with new ones.
Dispose of the used batteries according to the instruc-
tions on them or requirements set by your local
municipality.
VCAUTION
Misuse of batteries could cause them to rupture or
leak, which might result in fire, injury or the stain-
ing of nearby materials. Please read and observe
the precautions on page 3 carefully.
LP-P1000_OM_EF_vA_CS6.indb 22 2013/09/11 16:16
23
ENGLISH
Names and functions of parts (turntable)
a Turntable
Place records centered on the turntable.
b 45 RPM adapter
Use this when playing back records with large holes.
c Transport locking screw
Before using the record player, use a coin or other
tool to turn the transport locking screw clockwise
until it stops.
Turn this way
Side view of transport locking screw
Transport
position
(when shipped
from the factory)
Use position
Before transporting this unit (to move residences,
for example) turn the screw counterclockwise until
it stops to secure the turntable.
d Cue lever
Use this lever to lift the tone arm from the record.
e Tone arm holder
This is a rest for the tone arm. Gently push the clasp
to the right to release the tone arm before playing a
record.
f Rotation speed selection switch
Set the rotation speed (RPM) suitable for the record.
g Tone arm
When you move the tone arm toward the record,
the turntable will begin to turn.
Cue lever d
Tone arm g
Rotation speed selection switch f
Tone arm holder e
a
b
c
d
e
f
a
g
Before use, remove the
needle cover (white
plastic part) by pulling
it in the direction of the
arrow.
LP-P1000_OM_EF_vA_CS6.indb 23 2013/09/11 16:16
24
Turntable cover
Attaching the turntable cover
Hinge
Main unit
Turntable cover
1 Insert the hinges completely into the
hinge holders at the left and right ends
of the back of the main unit.
2 Align the tops of the hinges with the
turntable cover hinge holders and
insert them.
Removing the turntable cover
Hold both edges of the turntable cover and lift it slowly
to remove it along with the hinges from the unit. Then,
remove the hinges from the turntable cover.
Opening and closing the turntable cover
Open
Opening
Hold the front edge of the turntable cover and gently
lift it open completely until it stops.
The turntable cover will stay open in this position.
Closing
Gently lower the turntable cover until it is closed.
V Be careful not to pinch your hand, for exam-
ple, when closing the turntable cover.
LP-P1000_OM_EF_vA_CS6.indb 24 2013/09/11 16:16