Autec s r l FJMNZ422 Transceiver unit User Manual 1
Autec s.r.l. Transceiver unit 1
Contents
User Manual 1
Original instructions
DYNAMIC SERIES
Part B:
Conformity and frequencies
(915MHz - FCC/IC)
INDEX
1 Conformity ............................................................................................................. 2
1.1 Federal Communications Commission (FCC) ................................................... 3
1.2 Industry Canada (IC) ........................................................................................ 3
2 Frequencies ........................................................................................................... 3
2.1 Dynamic mode ................................................................................................. 3
2.2 Static mode ...................................................................................................... 3
3 Market .................................................................................................................... 4
AUTEC LIDY2E00-08_new
2
LIDY2E00-08_new
Conformity
AUTEC - Dynamic Series
1 Conformity
Each Dynamic series' radio remote control working in the frequency band 915-928MHz
complies with Part 15 of standards FCC and with RSS-210 of IC standards.
Unit FCC ID IC number
ADD OQA-ADDNE022 d9061A-ADDNE022 a b c
ARM OQA-ARMNB022 d
OQA-ARMNC022 d
9061A-ARMNB022 a b c
9061A-ARMNC022 a b c
ARS OQA-ARSND022 d9061A-ARSND022 a b c
ARX OQA-ARXNG022 d9061A-ARXNG022 a b c
CRS OQA-CRSNA022 d9061A-CRSNA022 a b c
CRX OQA-CRXNH022 d9061A-CRXNH022 a b c
FJL OQA-FJLNF022 9061A-FJLNF022
FJM OQA-FJMNF022 9061A-FJMNF022
FJM OQA-FJMNZ422 9061A-FJMNZ422
FJR OQA-FJRNF022 9061A-FJRNF022
FJR OQA-FJRNZ422 9061A-FJRNZ422
FJS OQA-FJSNF022 9061A-FJSNF022
a. Under Industry Canada regulations, this radio transmitter may only operate using an antenna
of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To
reduce potential radio interference to other users, the antenna type and its gain should be so
chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary
for successful communication.
b. This radio transmitter has been approved by Industry Canada to operate with the antenna types
listed below with the maximum permissible gain and required antenna impedance for each antenna
type indicated. Antenna types not included in this list, having a gain greater than the maximum
gain indicated for that type, are strictly prohibited for use with this device.
Antenna type Antenna gain Antenna impedance
Autec stylus λ/4 <2dBi 50 Ohm
Autec stylus λ/4 with 5m
RG58 <2dBi 50 Ohm
c. Autec allows you to use only the dedicated antenna supplied either with the remote control or
as original spare part. The use of any other type of antenna is prohibited and will invalidate the
guarantee.
d. Place the antenna of the receiving unit in a position that ensures a minimum separation distance
of 20cm with all the people that can be in the working area.
AUTEC - Dynamic Series
Frequencies 3
LIDY2E00-08_new
1.1 Federal Communications Commission (FCC)
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
Any changes or modications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
1.2 Industry Canada (IC)
This device complies with Industry Canada’s licence-exempt RSSs.
Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired
operation of the device..
2 Frequencies
The radio link between the units of Autec Dynamic series radio remote controls is established
at one of the frequencies permitted by the US, Canadian and Australian standards in force
when the system is put on the market.
Frequency band ............................................................................................ 915-928MHz
RF power ........................................................................ meets FCC and IC requirements
Available radio channels .............................................................................................. 259
Channel spacing ...................................................................................................... 50kHz
Dynamic series industrial radio remote controls communicate either in dynamic or static
mode. Mode is set by the machine manufacturer.
2.1 Dynamic mode
A radio remote control communicating in dynamic mode:
-uses a working frequency in the band 915-928MHz
-checks that the frequency is free before using it
-continually changes the working frequency to maintain the radio link even when interference
occurs.
2.2 Static mode
A radio remote control communicating in static mode:
-uses a working frequency in the band 915-928MHz
-checks that the frequency is free before using it
-always works at the same frequency until the stop function is activated.
4
LIDY2E00-08_new
Market
AUTEC - Dynamic Series
3 Market
Dynamic series' radio remote controls working in the frequency band 915-928MHz can be
used in the US, Canadian and Australian markets.