CAEN RFID srl CAENRFID010 Low Power OEM UHF Compact RFID Reader User Manual CAENRFIDLibrary
CAEN RFID srl Low Power OEM UHF Compact RFID Reader CAENRFIDLibrary
Contents
- 1. Users Manual I
- 2. Users Manual II
- 3. Users Manual III
- 4. Users Manual IV
- 5. User Manual
Users Manual III
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1405618 |
| Application ID | Us84MbO0Yej+kv5yhg7NKw== |
| Document Description | Users Manual III |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 96.83kB (1210314 bits) |
| Date Submitted | 2011-01-17 00:00:00 |
| Date Available | 2011-01-17 00:00:00 |
| Creation Date | 2010-12-22 14:02:48 |
| Producing Software | Microsoft® Office Word 2007 |
| Document Lastmod | 2010-12-22 14:02:48 |
| Document Title | CAENRFIDLibrary |
| Document Creator | Microsoft® Office Word 2007 |
| Document Author: | manuela |
R1230CB OEM UHF Multiregional Ultra Compact Reader R1230CBEVB Quark Reader Evaluation Board R1230ADAT Quark Adapter Board Technical Information Manual Revision n. 00 25/11/2010 Scope of Manual The goal of this manual is to provide the basic information to work with the QUARK family. Change Document Record Date 25 Nov 2010 Revision 00 Changes Preliminary release. CAEN RFID srl Via Vetraia, 11 55049 Viareggio (LU) - ITALY Tel. +39.0584.388.398 Fax +39.0584.388.959 info@caenrfid.it www.caenrfid.it © CAEN RFID srl – 2010 Disclaimer No part of this manual may be reproduced in any form or by any means, electronic, mechanical, recording, or otherwise, without the prior written permission of CAEN RFID. The information contained herein has been carefully checked and is believed to be accurate; however, no responsibility is assumed for inaccuracies. CAEN RFID reserves the right to modify its products specifications without giving any notice; for up to date information please visit www.caenrfid.it. Federal Communications Commission (FCC) Notice (Preliminary) This device was tested and found to comply with the limits set forth in Part 15 of the FCC Rules. Operation is subject to the following conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This device generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instruction manual, the product may cause harmful interference to radio communications. Operation of this product in a residential area is likely to cause harmful interference, in which case, the user is required to correct the interference at their own expense. The authority to operate this product is conditioned by the requirements that no modifications be made to the equipment unless the changes or modifications are expressly approved by CAEN RFID. Preliminary Product Information This document contains information for a new product. CAEN RFID reserves the right to modify this product without notice. “Preliminary” product information describes products that are ready for production, but for which full characterization data is not yet available. CAEN RFID believes that the information contained in this document is accurate and reliable. However, the information is subject to change without notice and is provided “AS IS” without warranty of any kind (Express or implied). You are advised to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. No responsibility is assumed by CAEN RFID for the use of this information, including use of this information as the basis for manufacture or sale of any items, or for infringement of patents or other rights of third parties. Disposal of the product Do not dispose the product in municipal or household waste. Please check your local regulations for disposal/recycle of electronic products. Index Scope of Manual .......................................................................................................................... 2 Change Document Record ........................................................................................................... 2 Index.......................................................................................................................................... 3 List of Figures ............................................................................................................................. 4 List of Tables .............................................................................................................................. 4 Introduction ....................................................................................................................... 5 General Information .................................................................................................................... 6 Ordering Code.............................................................................................................................. 7 Installation Notice........................................................................................................................ 8 Quark R1230CB .................................................................................................................. 9 Technical Specifications Table ................................................................................................... 10 External Connections ................................................................................................................. 11 R1230CB supply and I/O connector electrical characteristics ......................................... 13 Power supply connection ................................................................................................. 14 General purpose I/O connections .................................................................................... 14 External reset ................................................................................................................... 15 UART connection.............................................................................................................. 15 Antenna port specifications ............................................................................................. 15 Reader – Tag Link Profiles.......................................................................................................... 16 Firmware Upgrade ..................................................................................................................... 16 BLS operation ................................................................................................................... 16 Firmware upgrade via R1230CBEVB board ...................................................................... 17 PCB Pad Layout .......................................................................................................................... 17 Quark R1230CBEVB .......................................................................................................... 18 Technical Specifications Table ................................................................................................... 19 Connection diagram .................................................................................................................. 19 Technical drawings .................................................................................................................... 20 Electrical scheme ....................................................................................................................... 21 External Connections ................................................................................................................. 22 Quark R1230ADAT ............................................................................................................ 23 Technical Specifications Table ................................................................................................... 24 Technical drawings .................................................................................................................... 24 Electrical scheme ....................................................................................................................... 25 External Connections ................................................................................................................. 26 Quark Regulatory Compliance .......................................................................................... 27 FCC Compliance ......................................................................................................................... 28 QUARK R1230CB - R1230BEVB - R1230ADAT - Technical Information Manual List of Figures Fig. 1.1: QUARK R1230CB OEM UHF Multiregional compact reader................................................... 6 Fig. 1.2: QUARK R1230CBEVB - Quark Reader Evaluation Board ........................................................ 6 Fig. 1.3: QUARK R1230ADAT - Quark Adapter Board .......................................................................... 6 Fig. 1.4: Connection of the R1230CBEVB to the Quark R1230CB module. .......................................... 8 Fig. 1.5: Connection of the R1230ADAT to the Quark R1230CB module. ........................................... 8 Fig. 2.1: QUARK R1230CB technical drawings: top view.................................................................... 11 Fig. 2.2: QUARK R1230CB technical drawings: lateral views ............................................................. 11 Fig. 2.3: QUARK R1230CB power supply connection ......................................................................... 14 Fig. 2.4: QUARK R1230CB GPIO connection example ........................................................................ 14 Fig. 2.5: QUARK R1230CB external reset ........................................................................................... 15 Fig. 2.6: QUARK R1230CB RS232 connection ..................................................................................... 15 Fig. 2.7: BSL sequence ........................................................................................................................ 16 Fig. 2.8: QUARK R1230CB upgrade program window........................................................................ 17 Fig. 2.9: PCB pad layout...................................................................................................................... 17 Fig. 3.1: Quark R1230CBEVB technical drawing................................................................................. 20 Fig. 3.2: Quark R1230CBEVB electrical scheme ................................................................................. 21 Fig. 4.1: Quark R1230ADAT technical drawing .................................................................................. 24 Fig. 4.2: Quark R1230ADAT electrical scheme ................................................................................... 25 List of Tables Tab. 2.1: QUARK R1230CB Technical Specifications .......................................................................... 10 Tab. 2.2: QUARK R1230CB connector pinout .................................................................................... 12 Tab. 2.3: QUARK R1230CB supply and I/O connector electrical characteristics ............................... 13 Tab. 2.4: RF port pinout ..................................................................................................................... 15 Tab. 2.5: RF port electrical characteristics ......................................................................................... 16 Tab. 2.6: QUARK R1230CB reader to tag link profiles........................................................................ 16 Tab. 3.1: QUARK R1230CBEVB Technical Specifications.................................................................... 19 Tab. 3.2: QUARK R1230CBEVB connector pinout .............................................................................. 22 Tab. 4.1: QUARK R1230ADAT Technical Specifications ..................................................................... 24 Tab. 4.2: QUARK R1230ADAT connector pinout ................................................................................ 26 QUARK R1230CB - R1230BEVB - R1230ADAT - Technical Information Manual 1 Introduction This Chapter gives general information about the Quark family. It contains these topics: General Information Ordering Code Installation Notice QUARK R1230CB - R1230BEVB - R1230ADAT - Technical Information Manual General Information The Quark (Model R1230CB), the new OEM reader of the easy2read© Family, is an UHF multiregional ultra compact reader for low-power, high performances UHF RFID applications. With programmable output power in 15 steps from 9dBm to 23dBm, the reader can detect tags at more than 2 mt of distance (depending on antenna and tag dimensions). Due to its low power consumption, the module is specifically designed to be easily integrated in battery powered devices as well as powered directly by a standard USB port. The radio frequency core of the module permits to achieve fast reading and to be used in dense reader and dense tag environments for top-class rated performances. The compactness of the device and the board-to-board connector allow to embed the R1230CB inside the new small form factor industrial handhelds, smartphone accessories, small USB dongles and other compact form factor devices. The R1230CB complies with and can operate in both European and US regulatory environments and due to its multiregional capabilities, it is ideal for integration in devices requiring compliance to different geographical regions. The Mod. R1230CBEVB evaluation board allows to manage the Mod. R1230CB OEM UHF multiregional Compact Reader directly via USB In case customers want to replace directly with Quark reader others CAEN RFID OEM modules (i.e. A828, A828A, A528), the Mod. R1230ADAT adapter board can be used. Fig. 1.1: QUARK R1230CB OEM UHF Multiregional compact reader Fig. 1.2: QUARK R1230CBEVB - Quark Reader Evaluation Board Fig. 1.3: QUARK R1230ADAT - Quark Adapter Board QUARK R1230CB - R1230BEVB - R1230ADAT - Technical Information Manual It is also available the R1230CBDK Development KIT with QUARK reader, antenna, tags. Kit contents: no. 1 R1230CB - Quark Low Power OEM UHF Compact RFID Reader no. 1 R1230CBEVB - Quark Reader Evaluation Board no. 5 WEPCLABEL002 - EPC C1G2 Label Short Dipole EU no. 1 A927Z - Temperature logger UHF semi-passive tag (EPC C1G2) no. 1 RT0005 - Temperature logger UHF semi-passive tag (EPC C1G2) Blistered no. 1 WANTENNAX009 - Linear polarized antenna for printers 865 - 870 MHz (ETSI) no. 1 WANTENNAX012 - Linear polarized antenna for printers 902 - 928 MHz (FCC) no. 1 cable MINI USB - no. 1 CD-ROM containing SW libraries, CAENRFID demo SW and technical manuals Ordering Code Code WR1230ADAT01 WR1230CBEVBX WR1230CXBAAA WR1230CBDKEU Description R1230ADAT - Quark Adapter Board R1230CBEVB - Quark Reader Evaluation Board R1230CB – Quark Low Power OEM UHF Compact RFID Reader R1230CBDK - Development KIT with QUARK reader, antenna, tags QUARK R1230CB - R1230BEVB - R1230ADAT - Technical Information Manual Installation Notice The correct way to connect the Quark R1230CB module to the evaluation board and the adapter board is shown in the following pictures. Fig. 1.4: Connection of the R1230CBEVB to the Quark R1230CB module. Fig. 1.5: Connection of the R1230ADAT to the Quark R1230CB module. QUARK R1230CB - R1230BEVB - R1230ADAT - Technical Information Manual 2 Quark R1230CB This Chapter provide the basic information to work with the Quark R1230CB multiregional ultra compact reader. It contains these topics: Technical Specifications Table External Connections Reader – Tag Link Profiles Firmware Upgrade PCB Pad Layout QUARK R1230CB - R1230BEVB - R1230ADAT - Technical Information Manual Technical Specifications Table Frequency Band Output Power Level Output Power Accuracy Antenna VSWR Requirement Antenna Connector Frequency Tolerance Number of Channels Standard Compliance Digital I/O UART Serial Port Dimensions Supply Voltage Range Power Consumption Operating Temperature Weight 902÷928 MHz (FCC part 15) 865.600÷867.600 MHz (ETSI EN 302 208) Programmable in 15 levels (1dB step) from 9dBm to 23dBm (from 8mW to 200mW) conducted +/- 1dB 2:1 or better for optimum performances Nr. 1 MMCX type ±10 ppm over the entire temperature range 4 channels (compliant to ETSI EN 302 208 v1.2.1) 50 hopping channels (compliant to FCC part 15.247). All subsets of 902-928 MHz band are supported EPC C1G2 Others by FW upgrade Four I/O lines 3.3V out @ 3mA; 3.3V input level Baudrate: 115200 Databits: 8 Stopbits: 1 Parity: none Flow control: none 3.3 V I/O voltage level 9.6÷115 kbit/s data rate (settable) (W)25 x (L)40 x (H)6 mm (1.0 x 1.6 x 0.2 inch ) 2.5V ÷ 5.5V - 1.6W @ RF out = 23dBm - 1.3W @ RF out = 17dBm - 0.25W in idle mode -10 °C to +55 °C 8g Tab. 2.1: QUARK R1230CB Technical Specifications 10 QUARK R1230CB - R1230BEVB - R1230ADAT - Technical Information Manual External Connections The location of the connectors is shown in Fig. 2.1. Their mechanical specifications are listed below: Antenna Port: RF Coax Connector Huber+Suhner type 82MMCX-S50-0-2/111_K (to be used with Huber+Suhner type 11MMCX-50-1-1/111_O). Supply and I/O connector: Molex P.N. 53748-0208 (mates with Molex 52991-0208 to be used on the host board). Fig. 2.1: QUARK R1230CB technical drawings: top view Fig. 2.2: QUARK R1230CB technical drawings: lateral views QUARK R1230CB - R1230BEVB - R1230ADAT - Technical Information Manual 11 1 Supply and I/O connector pinout is shown in the following table : Pin # 10 11 12 13 14 15 16 17 18 19 20 Signal GND TCK GND /RST TXD TMS RXD TDI 5V_OUT TDO BSL_SEL TST VDD_M GPIO0 VDD_M GPIO1 VIN GPIO2 VIN GPIO3 Description Ground TCK JTAG signal (debug purpose only) Ground Reset (active low) UART TX to host TMS JTAG signal (debug purpose only) UART RX from host TDI JTAG signal (debug purpose only) 5Vdc auxiliary output voltage TDO JTAG signal (debug purpose only) Bootloader interface selection TST JTAG signal (also for BSL operation) 3.3Vdc auxiliary output voltage General Purpose IO #0 3.3Vdc auxiliary output voltage General Purpose IO #1 Input supply voltage General Purpose IO #2 Input supply voltage General Purpose IO #3 Tab. 2.2: QUARK R1230CB connector pinout The GPIO0-GPIO3 pins are 4 general purpose bidirectional pins, their default direction (or after a Reset) is input. The RXD/TXD pins are used to communicate with the Quark reader via UART port; to establish a link with the device you must configure your COM port as follows: Baud rate: 115200 Parity: None Data bits: Stop bits: Flow Control: none JTAG pins, unless otherwise noted, are for internal debug purpose only and shall not be connected by the user. /RST, BSL_SEL and TST pins shall be properly driven to start the bootloader of R1230CB embedded microcontroller in case the user wants to upgrade the firmware image of the reader. In normal operation BSL_SEL and TST shall be at low level or left unconnected. See § BLS operation (pag. 16) for the description of bootloader operation. VDD_M and 5V_OUT are two auxiliary supply sources with 20mA maximum current capability to be used as supply voltages of external components. Debug purpose and unused pins should not be connected. If BSL_SEL is at high level, the UART interface is connected to the serial port dedicated to microcontroller Boot Strap Loader operation required for flashing the firmware inside the MCU memory. This pin shall be at low level or left unconnected in normal operation. 12 QUARK R1230CB - R1230BEVB - R1230ADAT - Technical Information Manual R1230CB supply and I/O connector electrical characteristics3 Pin name Pin No. GND 1,3 TCK Parameter Min VIL VIH Type Max Unit -0.3 0.75 1.5 3.6 10 μA VIL -0.3 0.6 VIH 1.65 3.6 Input current /RESET TXD Internal pull-up resistance Pulse width 10 VOL 0.55 VOH 2.5 3.5 3.0 mA VIL -0.3 0.75 VIH 1.5 3.6 10 μA VIL -0.3 0.75 VIH 1.5 3.6 10 μA Input current TDI VIL -0.3 0.75 VIH 1.5 3.6 Input current 5V_OUT TDO 10 Output DC voltage 4.75 5.00 Output current 11 VDD_M GPIO[0:3] 12 13,15 14, 16, 18, 20 20 mA VOH 2.5 3.5 3.0 μA 1.0 VIL -0.3 VIH 2.2 3.6 10 17,19 VIL -0.3 0.75 1.5 3.6 Internal pull-down resistance 45 Output DC voltage 3.1 Ω kΩ VIH kΩ 3.3 Output current 3.5 20 mA VOL 0.55 VOH 2.5 3.5 3.0 mA VIL -0.3 0.75 VIH 1.5 3.6 10 μA 5.5 Output current Input supply voltage 0.55 Input current VIN μA Internal pull-down resistance TST 10 5.25 VOL Output current BSL_SEL μs Input current RXD 47 Output current TMS 2.5 Supply current @ Vin = 2.5V 0.68 Supply current @ Vin = 3.7V 0.42 Supply current @ Vin = 5.0V 0.30 Tab. 2.3: QUARK R1230CB supply and I/O connector electrical characteristics Exceeding maximum values reported in the table may cause permanent damage to the model. External 100uF bypass capacitor between Vin and GND is recommended for proper operation. QUARK R1230CB - R1230BEVB - R1230ADAT - Technical Information Manual 13 Power supply connection In the following schematic suggested R1230CB power supply connection is shown. An external 100uF bypass capacitor between Vin and GND is recommended for proper operation. The use of fuse F1 (or an equivalent solid state current limiter) is recommended since R1230CB doesn't provide internal current limitation protection. Fig. 2.3: QUARK R1230CB power supply connection General purpose I/O connections The GPIO0-GPIO3 pins are 4 general-purpose bidirectional pins. Their default direction after a power on reset or a general reset is set to input. GPIO, when configured as Outputs, can be used to drive indicators as leds or buzzers or to send trigger signal to others equipments. GPIO, when configured as Inputs, can accept control signals from other equipments or trigger signals from sensors (i.e. photocells). In the following schematic an example of application of GPIO is shown. Fig. 2.4: QUARK R1230CB GPIO connection example 14 QUARK R1230CB - R1230BEVB - R1230ADAT - Technical Information Manual External reset R1230CB manual reset can be performed by forcing at low level /RESET pin for 10μs at least. /RESET pin is pulled-up by an internal resistor. Fig. 2.5: QUARK R1230CB external reset UART connection The RXD/TXD pins are used to communicate with the R1230CB board via UART port. Since Quark RX/TX are TTL level signals, in order to connect it with a PC, a TTL/RS232 translator shall be used (please refer to the diagram below). To establish a link with the device host COM port shall be configured as follows: Baud rate: 115200 Parity: None Data bits: Stop bits: Flow Control: none Fig. 2.6: QUARK R1230CB RS232 connection Antenna port specifications In the following table the pinout of R1230CB antenna is shown. Pin # INNER OUTER Function RF OUT GND Direction OUT Description RF output Ground Tab. 2.4: RF port pinout QUARK R1230CB - R1230BEVB - R1230ADAT - Technical Information Manual 15 Parameter Min RF output power Output power vs. power setting accuracy RF port impedance Recommended antenna VSWR Typ. Max 200 23 ±1 50 2:1 Unit mW dBm dB Ω Tab. 2.5: RF port electrical characteristics Reader – Tag Link Profiles Quark reader supports different modulation and return link profiles according to EPC Class1 Gen2 protocol. In the following table are reported all profiles that have been tested for the compliance with ETSI and FCC regulations. Link profile # Regulation ETSI - FCC ETSI - FCC Modulation DSB–ASK; f=40kHz DSB–ASK; f=40kHz Return Link FM0; f = 40kHz Miller (M=4); f = 256kHz Tab. 2.6: QUARK R1230CB reader to tag link profiles Firmware Upgrade Quark reader firmware upgrade is based on Boot Start Loader (BSL) of the embedded microcontroller inside the module. An upgrade software has been developed to be used with Quark evaluation board (mod. R1230CBEVB). BLS operation In order to start the BSL of Quark internal microcontroller /RST, TST and BSL_SEL signal shall be driven as in the picture below: Fig. 2.7: BSL sequence The BSL program execution starts when TST pin has received a minimum of two positive transitions and if TST is high while /RST rises from low to high. BSL_SEL shall be at high level before BSL starts. Pulses length and distance between edges of all signals shall be 10ms at least. 16 QUARK R1230CB - R1230BEVB - R1230ADAT - Technical Information Manual Firmware upgrade via R1230CBEVB board Quark firmware upgrade can be managed via USB by using the evaluation board (mod.R1230CBEVB) and the SW upgrade program. In order to upgrade the firmware follow the steps below: - Connect to the USB port the evaluation board with the Quark reader installed - Verify the virtual COM port associated to the board - Open the FW upgrade program - Select the COM port - Select the image file by clicking on “Open” button - Click on “Upgrade” button - Disconnect the USB cable from the evaluation board - Connect again the USB cable in order to restore normal reader operation. Fig. 2.8: QUARK R1230CB upgrade program window PCB Pad Layout In the picture below the recommended PCB pad layout to be implemented on the user host board is shown. The 4 square pads shall be used to solder R1230CB shield and shall be connected to ground. In addition is shown the position and the layout required for Molex 52991-0208 connector, which mates with R1230CB supply and I/O connector, and which shall be soldered on the host board. 19 20 Fig. 2.9: PCB pad layout QUARK R1230CB - R1230BEVB - R1230ADAT - Technical Information Manual 17 3 Quark R1230CBEVB This Chapter provide the basic information to work with the Quark R1230CBEVB Evaluation Board. It contains these topics: 18 Technical Specifications Table Connection diagram Technical drawings Electrical scheme External Connections QUARK R1230CB - R1230BEVB - R1230ADAT - Technical Information Manual Technical Specifications Table Switch USB Port User Interface Dimensions Electrical Power Operating Temperature SW1= RESET SW2...SW5=GPIO USB Type A plug connector Bus powered USB 2.0 device Must be connected to Hight-power Port (500 mA @ VBUS) It appears as USB serial port Virtual Com Port (VCP) drivers for Windows XP/Vista/Seven (7), Windows CE 4.2, Linux 2.40 and greater Baudrate: 115200 Databits: 8 Stopbits: 1 Parity: none Flow control: none Red LED: Power Yellow LED: USB communication activity Green LED: GPIO[0..3]. (W)70.9 x (L)62.5 x (H)11.6 mm (2.8 x 2.5 x 0.5 inch ) DC Voltage 5V +/-5% Max 400 mA -10 °C to +55 °C Tab. 3.1: QUARK R1230CBEVB Technical Specifications Connection diagram The following block diagram shows how to connect the Mod. R1230CB with the PC host via the Mod. R1230CBEVB evaluation board. to host Antenna R1230CBEVB Molex Connector USB R1230CB OEM UHF Multiregional Ultra Compact Reader With Quark reader operating. QUARK R1230CB - R1230BEVB - R1230ADAT - Technical Information Manual 19 Technical drawings The location of the connectors is shown in Fig. 3.1. Their mechanical specifications are listed below: QUARK R1230CB mounting location Fig. 3.1: Quark R1230CBEVB technical drawing 20 QUARK R1230CB - R1230BEVB - R1230ADAT - Technical Information Manual Electrical scheme The electrical scheme of the Quark R1230CBEVB is shown in Fig. 3.2. Fig. 3.2: Quark R1230CBEVB electrical scheme QUARK R1230CB - R1230BEVB - R1230ADAT - Technical Information Manual 21 External Connections GPIO connector pinout is shown in the following table: Pin # Signal GPIO 1 GPIO 0 GPIO 2 GPIO 3 GND GND Tab. 3.2: QUARK R1230CBEVB connector pinout 22 QUARK R1230CB - R1230BEVB - R1230ADAT - Technical Information Manual 4 Quark R1230ADAT This Chapter provide the basic information to work with the Quark R1230ADAT Adapter Board. It contains these topics: Technical Specifications Table Technical drawings Electrical scheme External Connections QUARK R1230CB - R1230BEVB - R1230ADAT - Technical Information Manual 23 Technical Specifications Table Digital I/O Four I/O lines 3.3 V out @ 3mA Baudrate: 115200 Databits: 8 Stopbits: 1 Parity: none Flow control: none 3.3 V I/O voltage level 9.6÷115 kbit/s data rate (settable) (W)60 x (L)37 x (H)4.6 mm (2.4 x 1.5 x 0.2 inch ) 2.5V ÷ 5.5V -10 °C to +55 °C UART Serial Port Dimensions Supply Voltage Range Operating Temperature Tab. 4.1: QUARK R1230ADAT Technical Specifications Technical drawings The location of the connector is shown in Fig. 4.1. The mechanical specifications are listed below: QUARK R1230CB mounting location Fig. 4.1: Quark R1230ADAT technical drawing 24 QUARK R1230CB - R1230BEVB - R1230ADAT - Technical Information Manual Electrical scheme The electrical scheme of the Quark R1230ADAT is shown in Fig. 4.2. Fig. 4.2: Quark R1230ADAT electrical scheme QUARK R1230CB - R1230BEVB - R1230ADAT - Technical Information Manual 25 External Connections Supply and I/O connector pinout is shown in the following table: Pin # 10 11 12 Signal VIN /RST GPIO0 GPIO1 GPIO2 GPIO3 NC NC RXD TXD GND GND Description Input supply voltage Reset (active low) General Purpose IO #0 General Purpose IO #1 General Purpose IO #2 General Purpose IO #3 Not connected Not connected UART RX from host UART TX to host Ground Ground Tab. 4.2: QUARK R1230ADAT connector pinout 26 QUARK R1230CB - R1230BEVB - R1230ADAT - Technical Information Manual 5 Quark Regulatory Compliance 27 QUARK R1230CB - R1230BEVB - R1230ADAT - Technical Information Manual FCC Compliance This equipment has been tested and found to comply with Part 15 of the FCC Rules. NOTE: (a) Any changes or modification not approved by CAEN RFID could void the user’s authority to operate the equipment. (b) The QUARK R1230CB Module, which is rated at 200 mW output, is approved for operation with the CAENRFID antenna Mod. WANTENNAX012 (Linear polarized antenna 1.3dBi gain 902 - 928 MHz). Use of other than the approved antenna with this unit may result in harmful interference with other users, and cause the unit to fail to meet regulatory requirements. (c) The QUARK R1230CB transmitter module is approved for battery operation. In case that the module is embedded inside a device powered by AC line, the overall equipment shall be tested to comply with Section 15.207 requirements. 28 QUARK R1230CB - R1230BEVB - R1230ADAT - Technical Information Manual
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 28 Language : it-IT Tagged PDF : Yes Title : CAENRFIDLibrary Author : manuela Subject : 00107/05:A828x.MUTx/09 Keywords : 1.5 Creator : Microsoft® Office Word 2007 Create Date : 2010:12:22 14:02:48 Modify Date : 2010:12:22 14:02:48 Producer : Microsoft® Office Word 2007EXIF Metadata provided by EXIF.tools