CANTOPS CTS-ICOM IR PIO User Manual Appendix 8

Download:
Mirror Download [FCC.gov]
Document ID	2556965
Application ID	lkFL8ehYBFwjWU/w+h2dYA==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	20.15kB (251834 bits)
Date Submitted	2015-03-17 00:00:00
Date Available	2015-03-17 00:00:00
Creation Date	2015-03-17 13:17:32
Producing Software	Acrobat Distiller 9.0.0 (Windows)
Document Lastmod	2015-03-17 13:17:32
Document Title	Microsoft Word - Appendix 8. User Manual
Document Creator	PScript5.dll Version 5.2.2
Document Author:	bwshy

IR-PIO SPECIFICATION
CTS-ICOM-AA01 (EQ-PIO)
CTS-ICOM-AB01 (OHT-PIO)
* The wireless equipment concerned can result in jamming during operation.
2014. 3. 11 ( Ver 0.9 )
FCC STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC ID: RMNCTS-ICOM
WARNING! Changes or modifications to this unit not expressly approved
by the party responsible for compliance could void the user’s authority to
operate the equipment.
RF EXPOSURE WARNING! This equipment must be installed and operated
in accordance with provided instructions and the antenna(s) used for this
transmitter must be installed to provide a separation distance of at least 20
cm from all persons and must not be co-located or operating in
conjunction with any other antenna or transmitter. End-users and installers
must be provided with antenna installation instructions and transmitter
operating conditions for satisfying RF exposure compliance.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
[ Table of Contents ]
1. Product Outline
2. Product Feature
3. Wireless Communication Characteristics
4. IR Communication Characteristics
5. Product Code Configuration
6. IR Radiation Characteristics
7. Antenna Radiation Characteristics
8. Input/output Circuit
9. Product Specification
10. Tool Specification
11. Connector Connection Specification
12. LED Display Content
13. Major Pin Function
14. ID & CH Setting Method
15. RF Consideration When Installing a PIO
1. Product Outline
The CTS-ICOM Series is an IR communication device used to give and
receive 8-bit data in a non-contact type, and is a product with various
convenient functions using a 2.4GHz wireless communication technology.
This device is used to give and receive a SEMI-E84/E23 protocol or
maximum 8-bit input/output data wirelessly for an exchange of control
signals mainly between an AGV or OHT(Master or Active device), etc. and
equipment(Slave or Passive device).
This is a product to grasp causes quickly and establish measures easily
by providing various functions to analysis the causes in case of an
abnormality in data given and received during use.
2. Product Feature
 IR communication : For giving and receiving input/output data
 2.4GHz wireless communication : Additional function such as
downloading of transmission/reception data and F/W, etc.
 The wireless communication operating distance is maximum 5M
(However, there shall be no obstacles to electromagnetic waves in the
middle.)
 Designation of a wireless communication ID(address) : 6 digits
(hexadecimal code)
 For 8-bit input/output signals
 Storage of various information using a large-capacity SRAM : About 200
pieces of work such as communication data, absolute time, reception
signal intensity, etc. (Erased when power is OFF)
 Serial communication port : Setting change, communication data
information receiving, F/W downloading, etc.
3. Wireless Communication Characteristics
 RF communication using a 2.4GHz ISM(Industrial, Scientific and Medical)
band that can be used without permission
 Equipment name: Wireless device for a wireless data communication
system
 High-speed data communication of 1Mbps per channel
 GFSK modulation type, 1MHz bandwidth
 Superior expandability with an optional function of 6-byte serial number
and 2-byte frequency
 200uS or less channel switching time to minimize interference with
other wireless devices
 Possibility of frequency interference with 2.4GHz Bluetooth and wireless
communication devices
 RF maximum output power : 0dBm
 Sensitivity of the reception part : -90dBm
4. IR Communication Characteristics
 Wavelength : 870nm (infrared ray)
 Ambient brightness : 4000lx or less incandescent lamp and fluorescent
lamp, where there is no direct sunshine
 Transmission and reception method : Half Duplex
 Modulation method : Pulse Modulation
 Operating distance and angle : 0.5m at 0°, 0.25m at ±15°
 Communication distance regulation : Serial communication command
 Reception level regulation : For serial communication command and
ambient light noise removal
 Input signal and GO output filtering function : 0th ~ 10th (Serial
communication command)
5. Product Code Configuration
Item name
Feature
CTS-ICOM-AA01-xx-y-zz
(EQ, Slave)
25-pin DSUB, Male Type
(For equipment)
CTS-ICOM-AB01-xx-y-zz
(OHT, Master)
Hirose 26-pin, HIF6-26D-1.27R
(For OHT, AGV)
*) xx : The communication distance and unit are 0.1m, 05=0.5m, 10=1.0m
*) y : Transmission and reception window position, T=Top View, F=Front
View
*) zz : The cable length and unit are 0.1m, 25=2.5m
6. IR Radiation Characteristics
As shown in the figure below, the communicable angle is 30°, and
communication is possible from a 0.25m away distance at ±15° and from
a 0.5m away distance at 0°. If lighting, sunshine, IR remote control, IR type
sensor, etc. applies light directly to the transmission and reception window,
then there may happen loss of communication. In this case, shield the
external light and then use it.
+15°
-15°
0.25m
0.5m
7. Antenna Radiation Characteristics
The antenna used for this product is located at the position like the figure
below in the case. In order to exert the maximum performance without
jamming, the whole product except the fixing hole part had better be
arranged such that there may be no object that can cause jamming.
Especially, avoid metals or other objects that can cause jamming around
the antenna.
Antenna
IN
OUT
STATE
GO
Fixing hole(2 ea)
8. Input/output Circuit
 Input circuit : Maximum 10mA
PIO
RF-PIO
Inside
Inside
+24V
VCC
INPUT
 Output circuit : NPN type Open Collector, maximum operating current of
50mA / 30V
VCE max. 100mV / 10mA
RF-PIO
PIO
Inside
Inside
DCV
OUTPUT
9. Product Specification
Division
Specific item
Content
Displayed when IR communication
starts
Flashing as watchdog signals for
operating conditions
Display of operating conditions of
the 8Bit input port
Display of operating conditions of
the 8Bit output port
AA01 Model : 25-pin DSUB, Male,
2.5m, 5m
AB01 Model : Hirose 26-pin,
1.27mm pitch, 1m
26AWG x 22C + 24AWG x 3C, Foil
Shield
8 Bit, Photo-Coupler, 24V
On : 10mA, Off : 0.1mA or less
8Bit, Open Collector, NPN, 30V
Maximum operating current 50mA
GO
STATE
Display part
IN
OUT
Connection
connector
External equipment
Cable
connection
Input
Output
Communication
media
Communication
distance
Communication
angle
Communication
method
IR
Communication
Communication
window
function
location
Optical
modulation
type
Communication
error check
Communication
period
Communication
media
Additional
Frequency
communication(RF)
band
function
Safety function
870nm, Infrared
0.5m (0°), 0.25m (+15°, -15°)
30° ( ±15°)
1:1 communication, Half Duplex
T Type : Top View
F Type : Front View
Pulse Modulation
Parity
About 24ms when linked, about
48ms when communication is lost
2403~2480 MHz, bandwidth 1MHz
2403~2480 MHz, 78 channels*1)
Serial number confirmation function,
CRC-16
Environment
Power
Communication
1:1 communication, Half Duplex
type
PIO
serial
number
to
avoid
interference with neighboring PIOs,
ID setting
which
is
composed
of
16
digits(hexadecimal code)
Communication frequency to avoid
Channel setting interference with neighboring PIOs,
which is composed of 3 digits
ID setting
Serial communication command
method
F/W download, data download, time
Major function
setting, etc.
5m@0dBm(However, when there is
Operating
no objects causing jamming in the
distance
middle)
Storage temperature : -25 ~ 70°C
Storage
Storage humidity : 5 ~ 95%RH
environment
(However, there shall be no dew
condensation phenomenon)
Ambient brightness : 4000lx or less
(Incandescent lamp, fluorescent
lamp)
*) Install it such that no external
light may enter the reception part.
Operating
Operating temperature : 0 ~ 40°C
environment
Operating humidity : 35~85 %RH
(However, there shall be no dew
condensation phenomenon)
Vibration : 4~150 Hz, 4.9m/s2 or
less
Input voltage
DC 24V±10%
Consumed
current
100mA or less @ 24V
Case material
Polycarbonate
Size(WHD)
505320mm (Except the connector
overhang)
Weight
About 100g
*1) Can be used in an environment without frequency interference with other
wireless equipment(wireless LAN, Bluetooth, etc.)
10
10. Tool Specification
< F Type : Front View >
< T Type : Top View >
Unit: mm
11
11. Connector Connection Specification
 For equipment(CTS-ICOM-AA01) : For equipment(Slave), DSUB 25
pin, Pin Type, cable length 2.5m, 5m
 The Mode pin(#11) is connected to GND in the product, so it
doesn’t need to be connected.
Function
Pin No.
Function
Pin No.
IN 1
OUT 1
14
IN 2
OUT 2
15
IN 3
OUT 3
16
IN 4
OUT 4
17
IN 5
OUT 5
18
IN 6
OUT 6
19
IN 7
OUT 7
20
IN 8
OUT 8
21
Not Connected
Not Connected
22
SELECT
10
+VIN
23
MODE
11 (GND)
GND
24
Go (Ready)
12
GND
25
Not Connected
13
TxD
RxD
GND
Serial port
(DSUB 9 pins, arm)
12
 For OHT(CTS-ICOM-AB01) : Master, Hirose 26 pins, 1.27mm IDE
Connector
Function
Pin No.
Pin No.
Function
Input 1
16
Output 1
Input 2
17
Output 2
Input 3
18
Output 3
Input 4
19
Output 4
Input 5
20
Output 5
Input 6
21
Output 6
Input 7
22
Output 7
Input 8
23
10
Output 8
SELECT
14
Ready (Go)
MODE
15
12
+VIN
11, 24
GND
25, 26
13
GND
TxD
RxD
GND
Serial port
(DSUB 9 pins, arm)
13
12. LED Display Content
IN
OUT
STATE
GO
Fixing hole(2 ea)
LED
name
1~8
GO
STATE
Display content
The IN side displays the input condition, which is turned ON
when the Low is inputted.
The OUT side displays the output condition, which is turned ON
when the TR is turned ON.
Turned ON when data transmission/reception is realized
between PIOs.
Delay time until the GO LED is turned OFF after wireless
transmission/reception is disconnected: The filtering can be set
2 ~ 20 times(48ms*The number of filtering times).
Used as watchdog signals to check whether there is an
abnormality in this product or not, and the period of flashing
differs depending on master mode(0.25 sec), slave mode(1
sec) or standby mode(0.05 sec).
14
13. Major Pin Function
Signal
name
Usage
Mode
(Input)
Input to select a mode of PIO
▪ GND : Slave Mode (equipment)
▪ OPEN : Master Mode (OHT)
Select
(Input)
Input to operate the PIO
▪ GND : PIO function stop
▪ OPEN : PIO operation
GO
(Output)
Turned ON if communication is normally realized between
the Master PIO and the Slave PIO
 Master Mode : Opening the Select signal and operating the PIO transmits
optical signals. This is a mode attached to OHT or AGV and used.
 Slave Mode : Even opening the Select signal and operating the PIO
doesn’t transmit light, but only receives light, and then receiving
optical signals from the master transmits the data entering the input
port wirelessly. This is a mode attached to the equipment and used.
15
14. ID & CH Setting Method
The wireless function of CTS-ICOM Series is simultaneously connected
to many devices due to its wireless characteristics to be crossed, so in
order to communicate with a device, the ID and CH(channel) of the
communication counterparty shall be set before starting communication
and then communication shall be tried. This ID and CH setting is possible
using serial communication.
 Slave Mode : Connect it to the serial port of this device, and then set the
ID, channel and transmission power to use by using a
communication command. The set data is stored in EEPROM, so
even though power is turned OFF after set once, it doesn’t need to
be set again.
 Serial communication setting value: 57600,8,n,1, no flow control
 The starting letter for all commands is “<”, and the ending letter is “>”.
 The starting letter for a reply to a command is “[“, and the ending letter
is “]”.
 The ID uses 6 digits and hexadecimal codes
 Command to change the address
1) Setting : 
2) Confirmation : Reply : [A=AB95-623456]
3) Setting value during shipment: 0000-000000
 Command to change the address and the channel at a time
1) Setting : 
2) Confirmation : Reply[B=AB95-B54321:34]
3) Setting value during shipment: 0000-000000:00
 Command to set a channel
1) Setting : 
2) Confirmation : Reply : [C=40]
3) Setting value during shipment: 00
 Command to set the transmission power
1) Setting : 
2) Confirmation : 
Reply : [P=3]
3) Setting value during shipment: 3
 Command to receive real-time communication data in serial
1) Setting :  data output,  no output
2) Confirmation : Reply : [D=0]
3) Setting value during shipment: 0
16
 Command to set the time
1) Setting : 
2) Confirmation : Reply : [T=10/08/17 23:33:41-2]
3) Setting value during shipment: 10/01/01 00:00:00
 Check the F/W version.
1) Confirmation : Reply : [V=1.30]
17
15. RF Consideration when Installing a PIO
Intensity of electromagnetic wave : The length of the arrow in the figure
below indicates the size of electromagnetic waves emitted from the PIO,
so the electromagnetic waves are emitted the most to the up direction.
Therefore, a structure facing a possible sensor end(green part, the area
with an antenna) is the most desirable.
Caution
1) Metals, mirrors and other objects existing in a space at the straight-line
distance between two sensors reduce the wireless performance.
Remove the obstacles on the wireless path as far as possible.
2) You can use it stably without communication errors when there is no
interference with other wireless devices in an open space.
3) There is an antenna around the green part in the above figure. Take care
so that there may be no metals or other obstacles within a 60mm
radius around this antenna.
4) There may happen frequency interference due to other RF devices
around. Use this in an environment without frequency interference for
stable operation.
5) Especially, when using this together with a device using a 2.4GHz band,
allocate a channel such that the used channels may not be overlapped.
6) Maintain an 20cm or more interval between PIOs for equipment that are
installed in the equipment.
*) The specification of this product is subject to changes without prior
notice to improve the performance of the product.
18

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : bwshy
Create Date                     : 2015:03:17 13:17:32+09:00
Modify Date                     : 2015:03:17 13:17:32+09:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Creator Tool                    : PScript5.dll Version 5.2.2
Producer                        : Acrobat Distiller 9.0.0 (Windows)
Format                          : application/pdf
Title                           : Microsoft Word - Appendix 8. User Manual
Creator                         : bwshy
Document ID                     : uuid:42875b65-19c2-4d7f-83a3-02b961ebd1de
Instance ID                     : uuid:65995dcc-e767-4941-8fc8-2d32f8eba2da
Page Count                      : 18