Cambium Networks XS35004 XS-3500 Wireless LAN Array User Manual xirrus

Download:
Mirror Download [FCC.gov]
Document ID	609615
Application ID	baGKSnFTQsUkM4Nhxf74Nw==
Document Description	Users Manual Part 2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	136.57kB (1707151 bits)
Date Submitted	2005-12-07 00:00:00
Date Available	2005-12-07 00:00:00
Creation Date	2005-11-09 12:58:53
Producing Software	Acrobat Distiller 6.0.1 (Windows)
Document Lastmod	2005-11-09 12:59:09
Document Title	xirrus.book
Document Creator	FrameMaker 6.0
Document Author:	Administrator

Wireless LAN Array
Element
Security
Specifications
Wireless Security:
WEP 40bit/128bit encryption
WPA with TKIP and AES encryption
Misappropriated APs automatically reset to
factory defaults (requires the Xirrus Wireless
Management System)
Rogue AP detection, with alerts and
classification
User and System Authentication:
WPA Pre-Shared Key authentication
Embedded RADIUS Server
802.1x EAP-TLS
802.1x EAP-TTLS
802.1x PEAP
External RADIUS servers
Authentication of Xirrus Arrays to the Xirrus
Management System (XM-3300)
Introduction
19
Wireless LAN Array
Element
Wireless
Specifications
Number of Radios:
4 x 802.11a/b/g radios
Wireless Standards:
802.11a/b/g and g-only mode
802.11e (draft), 802.11i
Channel Selection:
Manual
Automatic
Frequency Bands:
11a: 5.15-5.25 GHz (UNII 1)
11a: 5.15-5.25 GHz (TELEC)
11a: 5.25-5.35 GHz (UNII 2)
11a: 5.470-5.725 (ETSI)
11a: 5.725-5825 GHz (UNII 3)
11b/g: 2.412-2.462 GHz (FCC)
11b/g: 2.412-2.472 GHz (ETSI)
11b/g: 2.412-2.484 GHz (TELEC)
Antenna:
4 internal 3 dBi 180° 802.11b/g sectorized
antennas
1 internal 2 dBi 360° omni-directional antenna
External RP-TNC connector
Radio Approvals:
FCC (United States)
EN 301.893 (Europe)
20
Compliance
UL / cUL 60950 and EN 60950
FCC Part 15.107 and 15109, Class A
EN 301.489 (Europe)
Warranty
One year (hardware), 90 day (software)
Introduction
Wireless LAN Array
Installing the Xirrus Array
This chapter defines the prerequisites for installing the Xirrus Array and provides
instructions to help you complete a successful installation. Section headings for
this chapter include:
“Installation Prerequisites” on page 21
“Planning Your Installation” on page 24
“Installation Workflow” on page 39
“Unpacking the Xirrus Array” on page 40
“Installing Your Xirrus Wireless LAN Array” on page 41
“Powering Up the Xirrus Wireless LAN Array” on page 51
“Establishing Communication with the Array” on page 53
“Performing the Express Setup Procedure” on page 54
Installation Prerequisites
Your Xirrus Array deployment requires the presence of hardware and services in
the host wired/wireless network, including:
Dedicated AC power outlet
Unless you are using the Xirrus Remote DC Power System (XP-3100) with
the DC version of the Xirrus Array, you need a dedicated power outlet to
supply AC power to each unit deployed at the site. If you are using the
optional XP-3100, then DC power is supplied to all units and only one AC
outlet is required for the XP-3100.
Ethernet port (read notes)
You need at least one 10/100/1000 BaseT port to establish wired Gigabit
Ethernet connectivity (via the product’s Gigabit 1 or Gigabit 2 port) and
one 10/100 BaseT port (if desired) for product management.
The Array’s Ethernet ports should be plugged into an Ethernet
switch, not an Ethernet hub—if a hub is used, we recommend that
you connect only one Ethernet port.
Installing the Xirrus Array
21
Wireless LAN Array
The Gigabit1 Ethernet interface is the primary port for both data
and management traffic. If a single Ethernet connection is used, it
must be connected to the Gigabit1 Ethernet interface.
The 10/100 Ethernet Port can be used for managing the Array, and
will only bridge management traffic. See also, “Port Failover
Protection” on page 33.
Secure Shell (SSH) utility
To establish secure remote command line access to the Array, you need a
Secure Shell (SSH) utility, such as PuTTY.
Secure Web browser
Either Internet Explorer (version 6.0 or higher), Netscape Navigator
(version 7.0 or higher), or Mozilla Firefox (version 1.01 or higher) and it
must be available on the same subnet as the Array. A secure Web browser
is required for Web-based management of the Array.
Serial connection capability
To connect directly to the console port on the Array, your computer must
be equipped with a male 9-pin serial port and terminal emulation
software (for example, HyperTerminal).
Use the following settings when establishing a serial connection:
Bits per second
Data bits
Parity
Stop bits
Flow control
22
115,200
None
None
Installing the Xirrus Array
Wireless LAN Array
Optional Network Components
The following network components are optional.
DHCP server
To distribute IP addresses and ancillary information to your Xirrus Array.
Xirrus Wireless Management System (XM-3300)
The optional XM-3300 offers powerful management features for small or
large Xirrus Array deployments.
Xirrus Remote DC Power System (XP-3100)
The optional XP-3100 provides distributed DC power to multiple Arrays,
eliminating the need to run dedicated AC power to each unit and
facilitating backup power when connected via a UPS.
External RADIUS server
Although your Array comes with an embedded RADIUS server, for
802.1x authentication in large deployments you may want to add an
external RADIUS server.
Client Requirements
The Xirrus Array should only be used with Wi-Fi certified client devices.
Installing the Xirrus Array
23
Wireless LAN Array
Planning Your Installation
This section provides guidelines and examples to help you plan your Xirrus
Array deployment to achieve the best overall coverage and performance. We
recommend you conduct a site survey to determine the best location and settings
for each Array you install.
General Deployment Considerations
The Xirrus Array’s unique multi-radio architecture generates 360 degrees of
sectored high-gain 802.11a/b/g coverage that provides extended range. However,
the number, thickness and location of walls, ceilings or other objects that the
wireless signals must pass through may affect the range. Typical ranges vary
depending on the types of materials and background RF (radio frequency) noise
at your location. To maximize wireless range, follow these basic guidelines:
1.
Keep the number of walls and ceilings between the Array and your
receiving devices to a minimum—each wall or ceiling can reduce the
wireless range from between 3 and 90 feet (1 to 30 meters). Position your
devices so that the number of walls or ceilings is minimized.
2.
Be aware of the direct line between each device. For example, a wall that
is 1.5 feet thick (half a meter) at 90° is actually almost 3 feet thick (or 1
meter) when viewed at a 45° angle. At an acute 2° degree angle the same
wall is over 42 feet (or 14 meters) thick! For best reception, try to ensure
that your wireless devices are positioned so that signals will travel
straight through a wall or ceiling.
90°
45°
2°
> 42 feet
< 3 feet
1.5 feet
Figure 8. Wall Thickness Considerations
24
Installing the Xirrus Array
Wireless LAN Array
3.
Building materials can make all the difference. For example, solid metal
doors or aluminum wall studs may adversely effect wireless signals. Try
to position wireless client devices so that the signal passes through
drywall (between studs) or open doorways and not other materials.
Coverage and Capacity Planning
This section considers coverage and capacity for your deployment(s), including
placement options, RF patterns and cell sizes, area calculations, roaming
considerations, and channel allocations.
Placement
Use the following guidelines when considering placement options:
1.
The best placement option for the Array is ceiling-mounted within an
open plan environment (cubicles rather than fixed walls).
2.
Keep the Array away from electrical devices or appliances that generate
RF noise. Because the Array is generally mounted on ceilings, be aware of
its position relative to lighting (especially fluorescent lighting)—we
recommend maintaining a distance of at least 3 to 6 feet (or 1 to 2 meters).
3.
If using multiple Arrays at the same location, we recommend
maintaining a distance of at least 100 feet between units.
≥ 100 ft
≥ 100 ft
≥ 100 ft
Figure 9. Unit Placement
Installing the Xirrus Array
25
Wireless LAN Array
RF Patterns
The Xirrus Array allows you to control—automatically or manually—the pattern
of wireless coverage that best suits your deployment needs. You can choose to
operate with full coverage, half coverage, or custom coverage (by enabling or
disabling individual sectors).
Full (Normal) Coverage
In normal operation, the Array provides a full 360 degrees of coverage.
Figure 10. Full (Normal) Coverage
Half Coverage
If installing a unit close to an exterior wall, you can deactivate half of the radios to
prevent redundant signals from “bleeding” beyond the wall and extending
service into public areas. The same principle applies if you want to restrict service
to an adjacent room within the site.
outside wall
Figure 11. Adjusting RF Patterns
26
Installing the Xirrus Array
Wireless LAN Array
Custom Coverage
Where there are highly reflective objects in close proximity to the Array, you can
turn off specific radios to avoid interference and feedback.
reflective
object
Figure 12. Custom Coverage
Calculating Areas
Before we discuss cell sizes, it is useful to know how to calculate the area of a
circle (because the Array radiates a full 360 degrees). The area of a circle is equal
to pi (π) times the square of the radius, where pi is equal to 3.14. The following
graphic calculates the area of a circle with a radius of 20 feet.
3.14 x 202 = 1,256 sq ft
20 ft
Figure 13. Calculating the Area of a Circle
Installing the Xirrus Array
27
Wireless LAN Array
Capacity and Cell Sizes
Cell sizes should be calculated based on the number of users, the applications
being used (for example, data/video/voice), and the number of Arrays available
at the location. The capacity of a cell is defined as the minimum data rate desired
for each sector multiplied by the total number of sectors being used.
The following chart shows the maximum recommended cell sizes for each data
rate.
Desired
Data Rate
(Mbps)
28
11a Cell Size
11b/g Cell Size
Radius
(feet)
Area
(sq. feet)
Radius
(feet)
Area
(sq. feet)
54
100
31,400
104
33,962
48
185
107,466
183
105,155
36
247
191,568
260
212,264
24
278
242,672
283
251,479
18
309
299,810
338
358,726
12
339
360,852
364
416,037
371
432,193
374
439,211
402
507,437
390
477,594
11
416
543,396
5.5
437
649,295
458
658,659
468
687,735
Installing the Xirrus Array
Wireless LAN Array
Sample 802.11a Cells
The following 802.11a sample cells illustrate the coverage area and minimum
throughput you can expect (per sector) based on the size of each cell. Notice how
the throughput increases as the cell size decreases, and vice versa.
68 ft
14,520 sq ft
54 Mbps per sector
98 ft
30,157 sq ft
36 Mbps per sector
165 ft
85,487 sq ft
18 Mbps per sector
Figure 14. Sample 802.11a Cells
Installing the Xirrus Array
29
Wireless LAN Array
Fine Tuning Cell Sizes
Adjusting the transmit power allows you to fine tune cell sizes. There are three
settings—Large, Medium, or Small (the default is Large). If you are installing
many units in close proximity to each other, reduce the transmit power to avoid
excessive interference with other Arrays or installed APs. See also, “IAP Settings”
on page 90.
Small
Medium
Large
Figure 15. Transmit Power
Roaming Considerations
Cells should overlap approximately 10 - 15% to accommodate client roaming.
ROAMING
10 - 15% overlap
Figure 16. Overlapping Cells
30
Installing the Xirrus Array
Wireless LAN Array
Allocating Channels
Because the Xirrus Array is a multi-channel device, allocating the best channels to
radios is important if peak performance is to be maintained.
Automatic Channel Selection
We recommend that you allow the Array to make intelligent channel allocation
decisions automatically. In the automatic mode, channels are allocated
dynamically, driven by changes in the environment.
Manual Channel Selection
You can manually assign channels on a per radio basis, though manual selection
is not recommended (and not necessary).
To avoid co-channel interference, do not select adjacent channels for radios that
are physically next to each other.
Maintain channel separation
Figure 17. Allocating Channels Manually
Installing the Xirrus Array
31
Wireless LAN Array
Deployment Examples
The following examples employ 802.11a cells, each offering minimum
throughputs of 54 Mbps, 36 Mbps, and 18 Mbps per sector respectively, and
assume a floor plan covering a total area of about 60,000 square feet.
Figure 18. Deployment Scenario (54 Mbps)—Per Sector
Figure 19. Deployment Scenario (36 Mbps)—Per Sector
32
Installing the Xirrus Array
Wireless LAN Array
Figure 20. Deployment Scenario (18 Mbps)—Per Sector
Failover Planning
This section discusses failover protection at the unit and port levels.
Port Failover Protection
To ensure that service is continued in the event of a port failure, you can utilize
the Gigabit 1 and Gigabit 2 ports simultaneously.
Multiple port connections
Ethernet switch
Figure 21. Port Failover Protection
Installing the Xirrus Array
33
Wireless LAN Array
In addition, the Array has full failover protection between the Gigabit 1 and
Gigabit 2 Ethernet ports (see following table).
Interface
Bridges
data?
Bridges
mgmt
traffic?
Fails over
to:
Fast Ethernet
No
Yes
None
DHCP or
static
Gigabit 1
Yes
Yes
Gigabit 2
DHCP or
static
Gigabit 2
Yes
Yes
Gigabit 1
Assumes the
IP address of
Gigabit 1
IP address
Switch Failover Protection
To ensure that service is continued in the event of a switch failure, you can
connect Arrays to more than one Ethernet switch (not a hub).
Ethernet connections
Backup switch
Ethernet switch
Figure 22. Switch Failover Protection
34
Gigabit Ethernet connections must be on the same subnet.
Installing the Xirrus Array
Wireless LAN Array
Power Planning
This section discusses the AC and DC power options.
AC Power
The AC power option requires a direct connection between the Array and a
dedicated AC power outlet. The power cord is provided with the unit.
Remote Distributed DC Power
To deliver DC power to the Array, you must have the optional Xirrus Remote DC
Power System (XP-3100) and a Xirrus Array that supports DC power—see
Figure 4 on page 8 . The XP-3100 provides DC power to multiple Arrays from a
single source, and requires only one AC power outlet.
Depending on the type of cable used, Arrays can be located up to 1,000 feet from
the XP-3100. In addition, the XP-3100 can be plugged into a UPS to prevent power
failure to all Arrays in the network.
When using CAT5 cable, DC power can be provided up to a distance of 300
feet.
Security Planning
This section offers some useful guidelines for defining your preferred encryption
and authentication method. For additional information, go to the Security section
of “Frequently Asked Questions” on page 222.
Wireless Encryption
Encryption ensures that no user can decipher another user’s data transmitted
over the airwaves. There are three encryption options available to you, including:
WEP-40bit or WEP-128bit
Because WEP is vulnerable to cracks, we recommend that you only use
this for legacy devices that cannot support a stronger encryption type.
Wi-Fi Protected Access
This is much more secure than WEP and uses TKIP for encryption.
Installing the Xirrus Array
35
Wireless LAN Array
Wi-Fi Protected Access with AES
This is government-grade encryption—available on most new client
adapters—and uses the AES–CCM encryption mode (Advanced
Encryption Standard–Counter Mode).
Authentication
Authentication ensures users are who they say they are, and occurs when users
attempt to join the wireless network and periodically there after. The following
authentication methods are available with the XS-3900:
36
RADIUS 802.1x
802.1x uses a remote RADIUS server to authenticate large numbers of
clients, and can handle different authentication methods (EAP-TLS, EAPTTLS EAP-PEAP).
Xirrus internal RADIUS server
Includes all the core functionality of a full RADIUS server built into the
Xirrus Array. Recommended for smaller numbers of users (about 100 or
less).
Pre-Shared Key
Uses a pass-phrase or key that is manually distributed to all authorized
users. The same passphrase is given to client devices and entered into
each Array.
MAC Access Control Lists (ACLs)
MAC access control lists provide a list of client adapter MAC addresses
that are allowed or denied access to the wireless network, and can be
used in addition to any of the above authentication methods. ACLs are
good for embedded devices, like printers and bar-code scanners (though
MAC addresses can be spoofed). The Xirrus Array supports 512 ACL
entries.
Installing the Xirrus Array
Wireless LAN Array
Network Management Planning
Network management can be performed using any of the following methods:
Command Line Interface, using an SSH (Secure Shell) utility, like PuTTY.
Web-based management, using the Array’s embedded Web Management
Interface (WMI). This method provides configuration and basic
monitoring tools, and is good for small deployments (one or two units).
Web-based management, using the optional Xirrus Wireless Management
System (XM-3300). The XM-3300 is used for managing large Array
deployments from a centralized Web-based interface and offers the
following features:
Š Layer 3 appliance
Š
Globally manage large numbers of Arrays
Š
Seamless view of the entire wireless network
Š
Easily configure large numbers of Arrays
Š
Rogue AP monitoring
Š
Easily manage system-wide firmware updates
Š
Monitor performance and trends
Š Aggregation of alerts and alarms
Installing the Xirrus Array
37
Wireless LAN Array
Deployment Summary
The following table summarizes your deployment options for small and large
deployments.
Number of Xirrus Arrays
Function
Power
One or Two
Three or More
AC
AC
DC (with XP-3100)
DC (with XP-3100)
UPS backup
(recommended)
Failover
Recommended
Highly recommended
VLANs
Optional
Optional use,
Can be used to put all
APs on one VLAN or
map to existing VLAN
scheme
Encryption
Authentication
WPA with TKIP
(recommended)
WPA with AES
(recommended)
PSK or 802.1x
802.1x keying
Internal RADIUS server
External RADIUS server
Pre-Shared Key
Management
Internal WMI
XM-3300
Internal CLI
XM-3300
38
Installing the Xirrus Array
Wireless LAN Array
Installation Workflow
This workflow illustrates the steps that are required to install and configure your
Xirrus Array successfully. Review this flowchart before attempting to install the
unit on a customer’s network.
Determine the number of Arrays needed
Choose the location(s) for your Xirrus Arrays
AC
AC or DC
power?
Run AC power and Ethernet cables
DC
Run DC power and Ethernet cables
Install the mounting plate
Connect the cables and turn on the power
Verify that the Ethernet link and radio LEDs are functioning correctly
Perform the Express Setup procedure
Figure 23. Installation Workflow
Installing the Xirrus Array
39
Wireless LAN Array
Unpacking the Xirrus Array
When you unpack your Xirrus Array, you will find the following items in the
carton:
Item
40
Quantity
Xirrus Wireless LAN Array
AC power cord
Console cable
Mounting plate
Mounting screws
Tile grid mounting clamps
Clamp nuts
Mounting template
CD-ROM containing:
This User’s Guide in PDF format
End User License Agreement (EULA)
README file
Quick Install Guide
Registration Card
Installing the Xirrus Array
Wireless LAN Array
Installing Your Xirrus Wireless LAN Array
This section provides instructions for installing your Xirrus Wireless LAN Array.
Choosing a Location
Based on coverage, capacity and deployment examples discussed earlier in this
chapter, choose a location for the Array that will provide the best results for your
needs. The Xirrus Array was designed to be mounted on a ceiling where the unit
is unobtrusive and wireless transmissions can travel unimpeded throughout open
plan areas. Choose a location that is central to your users (see the following
diagram for correct placement.
WRONG
RON
RO
ON
WRONG
RON
RO
O G
ON
CORRECT
ORRE
ORREC
Figure 24. Array Placement
Installing the Xirrus Array
41
Wireless LAN Array
Wiring Considerations
Unless you are using the Xirrus Remote DC Power System (XP-3100) with the DC
version of the Array, an AC power outlet must be available to the Array (an AC
power cord is provided with each unit). If you are using the XP-3100 to distribute
DC power to multiple Arrays, go to “Remote DC Power System (Optional)” on
page 8.
Once you have determined the best location for your Xirrus Array, you must run
cables to the location for the following services:
Power
Dedicated AC power
DC power (if using the XP-3100)
Network
42
Gigabit 1
Gigabit 2 (optional, not available on the XS-3500)
Fast Ethernet (optional, not available on the XS-3500)
Serial cable
Installing the Xirrus Array
Wireless LAN Array
Important Notes About Network Connections
Read the following notes before making any network connections.
The Array’s Ethernet ports should be plugged into an Ethernet switch,
not an Ethernet hub—if a hub is used, we recommend that you connect
only one Ethernet port.
The Gigabit1 Ethernet interface is the primary port for both data and
management traffic. If a single Ethernet connection is used, it must be
connected to the Gigabit1 Ethernet interface.
The 10/100 Ethernet Port can be used for managing the Array, and will
only bridge management traffic. See also, “Port Failover Protection” on
page 33.
When the unit’s IP address is unknown or a network connection has not
been established, the serial cable is used for connecting directly with the
Command Line Interface (CLI) via HyperTerminal. When a network
connection is established, the Array can be managed from any of the
available network connections, either Fast Ethernet, Gigabit 1 or
Gigabit 2.
Mounting the Unit
Most offices have drop-down acoustical ceiling tiles set into a standard grid. The
Xirrus Array has been designed to enable mounting to a tiled ceiling via a
mounting plate and clamps that attach to the grid. Once the mounting plate is
attached, the Array simply rotates onto the plate (similar to a smoke detector).
Once the unit is mounted it can be removed and re-attached easily, without the
need for tools or modifications to the original installation.
This section assumes that you are mounting the Array to a tiled ceiling. If your
ceiling is not tiled, the mounting plate can be attached directly to the ceiling with
the screws and anchors provided (without using the tile grid mounting clamps).
Installing the Xirrus Array
43
Wireless LAN Array
Attaching the T-Bar Clips
The T-bar clips are used to create four mounting points on the ceiling tile grid for
the Array mounting plate. Use the mounting template (provided) to find the
correct location for all four clamps. To attach the clamps, simply twist the clamps
onto the grid and tighten the screw post with a screwdriver.
Ceiling tile grid
Template
T-bar clips (4 places)
Tighten the screw post
Figure 25. Attaching the T-Bar Clips
44
Installing the Xirrus Array
Wireless LAN Array
Installing the Mounting Plate
If necessary, orient the mounting plate (see “Attaching the T-Bar Clips” on
page 44) and locate the plate on the four screw posts. Secure the mounting plate to
the four clamps using the nuts provided. Once the mounting plate is secured, cut
an access hole in the ceiling tile for the cables.
Tile grid
Mounting Plate
Cut an access hole here
Figure 26. Installing the Mounting Plate (XS-3900 shown)
Installing the Xirrus Array
45
Wireless LAN Array
Connecting the Cables
Feed the power and Ethernet cables through the access hole in the tile and the
mounting plate (XS-3900), then connect the cables to the unit. See also, “Wiring
Considerations” on page 42.
Figure 27. Connecting the Cables
When the cables are connected, turn on the power switch—before attaching the
unit to the mounting plate (next step). Verify that the Ethernet link LED lights and
the LED boot sequence begins. The radio LEDs on the front of the unit will
illuminate in rotation, indicating that the Xirrus Array software is loading and the
unit is functioning correctly.
46
Installing the Xirrus Array
Wireless LAN Array
Attaching the Array to the Mounting Plate (XS-3900)
Align the port recess on the Array with the access hole in the mounting plate, then
connect the Array with the lugs on the mounting plate (4 places) and turn the
Array clockwise to lock the unit into place (similar to a smoke detector).
Figure 28. Attaching the Unit (XS-3900)
Installing the Xirrus Array
47
Wireless LAN Array
Attaching the Array to the Mounting Plate (XS-3500)
Align the XS-3500 Wireless LAN Array with the key post on the mounting plate,
then turn the Array to the right to lock the unit into place at the 4 lugs—similar to
a smoke detector.
Key post
Lug
Alignment hole
Figure 29. Attaching the Unit (XS-3500)
48
Installing the Xirrus Array
Wireless LAN Array
Securing the Array
For added security, there is a locking bracket incorporated into the mounting
plate, which will accept a small luggage-style padlock (if desired). There is also a
Kensington lock slot located near the Ethernet ports. In addition, the mounting
plate incorporates a positive locking tab that prevents the unit from being
inadvertently released.
Locking bracket
Figure 30. Securing the Array
Now that the Array is physically installed, you must run the Express Setup
procedure from the unit’s Web Management Interface to enable the radios and
establish initial system configuration settings. Go to “Powering Up the Xirrus
Wireless LAN Array” on page 51.
Installing the Xirrus Array
49
Wireless LAN Array
Dismounting the Array
To dismount the Array, place your fingers so as to increase the space between the
Array and the mounting plate at the positions indicated by the decals on the
mounting plate—these are aligned with IAPs (radios) abg1 and abg3, as indicated
on the clock-face of the Array.
a12
a11
a1
abg4
abg1
a10
a2
a3
a9
a8
a4
abg3
abg2
a7
a5
a6
Figure 31. IAP Positions (XS-3900)
50
Installing the Xirrus Array
Wireless LAN Array
Powering Up the Xirrus Wireless LAN Array
When powering up, the Array follows a specific sequence of LED patterns
showing the boot progress, and following a successful boot will provide extensive
status information. The normal boot sequence is as follows:
1.
The green status LED will light first, showing a steady flashing while the
unit boots. In the event of a boot failure, this LED will change to flashing
red.
2.
The Ethernet Link/Activity LEDs on the underside of the Array will light
for those ports connected to the network.
3.
All IAP radio LEDs will light simultaneously.
4.
While the Array is booting, a sequential LED pattern will cycle through
all the radio LEDs.
5.
When the Array completes boot, the status LED will show a steady green,
and all radio lights will show the current state of those radios.
Ethernet
Activity LEDs
Status LED
IAP LEDs (x16)
Figure 32. LED Locations (XS-3900)
Installing the Xirrus Array
51
Wireless LAN Array
Once the unit is fully booted the default IAP LED display will be as follows:
IAP radio LEDs that are enabled will show a steady orange for 802.11a
radios, or green for 802.11b/g radios.
Once a client associates with an individual IAP, that LED will show a
slow flash (heartbeat) pattern.
When data is transmitted or received by an IAP, that IAP’s LED will flash.
The rate of flashing changes with the number of packets sent or received
per second—the LED will flash more quickly with a greater number of
packets per second and more slowly with lower numbers of packets per
second.
These settings may be altered or disabled entirely for diagnostic purposes or for
personal preference. Changes are made via the Array’s Command Line Interface
or the Web Management Interface—refer to “IAP LED Settings” on page 102.
Figure 33. WMI: IAP LED Settings Page
52
Installing the Xirrus Array
Wireless LAN Array
Establishing Communication with the Array
The Array can be configured through the Command Line Interface (CLI) or the
graphical Web Management Interface (WMI). You can use the CLI via the serial
management port, the Fast Ethernet port, or either of the Gigabit Ethernet ports.
You can use the WMI via any of the Array’s Ethernet ports.
Serial
Fast Ethernet
Gigabit 1
Gigabit 2
Figure 34. Network Interface Ports
Using the Serial Port
If using the serial port to make your connection, use serial settings of 8 bits, no
parity, 1 stop bit (8N1) and a speed setting of 115200 baud. Use the
communication package of your choice.
Using the Ethernet Ports
If the Array is booted and does not receive DHCP addresses on either the Fast
Ethernet or Gigabit Ethernet ports, the Fast Ethernet port will default to an IP
address of 10.0.0.1 and both Gigabit Ethernet ports will default to 10.0.1.1 and
10.0.2.1 respectively. If the Array is connected to a network that provides DHCP
addresses, the IP address can be determined by the following two methods:
1.
Examine the DHCP tables on the server and find the addresses assigned
to the Array (Xirrus MAC addresses begin with 000F7D).
2.
Query the Array using the CLI via the serial port. Use the show ethernet
command to view the IP addresses assigned to each port.
Logging In
When logging in to the Array, use the default user name and password—the
default user name is admin, and the default password is admin.
Installing the Xirrus Array
53
Wireless LAN Array
Performing the Express Setup Procedure
The Express Setup procedure allows you to establish global configuration settings
that will enable basic Array functionality. Any changes you make on this page
will affect all radios. When finished, click on the Apply button to apply the new
settings to this session, then click on the Save button to save your changes.
more ...
Figure 35. WMI: Express Setup Page (Part 1)
54
Installing the Xirrus Array
Wireless LAN Array
... continued
Figure 36. WMI: Express Setup Page (Part 2)
Procedure for Performing an Express Setup
1.
Host Name: Specify a unique host name for this Array. The host name is
used to identify the Array on the network. Use a name that will be
meaningful within your network environment, up to 64 alphanumeric
characters.
2.
Location Information: Enter a brief but meaningful description that
accurately defines the physical location of the Array. In an environment
where multiple units are installed, clear definitions for their locations are
important if you want to identify a specific unit.
3.
Admin Contact: Enter the name and contact information of the person
who is responsible for administering the Array at the designated location.
4.
Admin Email: Enter the email address of the admin contact you entered
in Step 3.
5.
Admin Phone: Enter the telephone number of the admin contact you
entered in Step 3.
6.
Enable/Configure All IAPs: Click on the Execute button to enable and
auto configure all IAPs (a message displays the countdown time—in
seconds—to complete the auto-configuration task).
Installing the Xirrus Array
55
Wireless LAN Array
7.
Configure the Fast Ethernet (10/100 Megabit), Gigabit 1 and Gigabit 2
network interfaces. The fields for each of these interfaces are the same,
and include:
a.
Enable Interface: Choose Yes to enable this network interface, or
choose No to disable the interface.
b. Allow Management on Interface: Choose Yes to allow management
of the Array via this network interface, or choose No to deny all
management privileges for this interface.
c.
8.
Configuration Server Protocol: Choose DHCP to instruct the Array
to use DHCP to assign IP addresses to the Array’s Ethernet interfaces,
or choose Static IP if you intend to enter IP addresses manually. If
you choose the Static IP option, you must enter the following
information:
IP Address: Enter a valid IP address for this Array. To use
any of the remote connections (Web, SNMP, or SSH), a valid
IP address must be used.
IP Subnet Mask: Enter a valid IP address for the subnet
mask (the default is 255.255.255.0). The subnet mask defines
the number of IP addresses that are available on the routed
subnet where the Array is located.
Default Gateway: Enter a valid IP address for the default
gateway. This is the IP address of the router that the Array
uses to forward data to other networks.
SSID (Wireless Network Name): The SSID (Service Set Identifier) is a
unique name that identifies a wireless network. All devices attempting to
connect to a specific WLAN must use the same SSID. The default for this
field is “xirrus.”
For additional information about SSIDs, go to the Multiple SSIDs section
of “Frequently Asked Questions” on page 222.
56
Installing the Xirrus Array
Wireless LAN Array
9.
Wireless Security: Select the desired wireless security scheme (Open,
WEP or WPA). Make your selection from the choices available in the pulldown list.
Open
This option offers no data encryption and is not recommended,
though you might choose this option if clients are required to use a
VPN connection through a secure SSH utility, like PuTTy.
WEP (Wired Equivalent Privacy)
An optional IEEE 802.11 function that offers frame transmission
privacy similar to a wired network. WEP generates secret shared
encryption keys that both source and destination stations can use to
alter frame bits to avoid disclosure to eavesdroppers.
WPA (Wi-Fi Protected Access)
A Wi-Fi Alliance standard that contains a subset of the IEEE 802.11i
standard, using TKIP or AES as an encryption method and 802.1X for
authentication. WPA is the stronger of the two wireless security
schemes.
For more information about security, including a full review of all
security options and settings, go to “Security Management” on page 113.
Security settings will only take effect if they are assigned to a specific
SSID. Refer to “SSID” on page 107.
10. Wireless Key/Passphrase: Depending on the wireless security scheme
you selected, enter a unique WEP key or WPA passphrase.
a.
Confirm Key/Passphrase: If you entered a WEP key or WPA
passphrase, confirm it here.
11. New Admin Password: If desired, enter a new administration password
for managing this Array. Choose a password that is not obvious, and one
that you can remember. If you forget your password, you must reset the
Array to its factory defaults so that the password is reset to admin (its
default setting).
Installing the Xirrus Array
57
Wireless LAN Array
a.
Confirm Admin Password: If you entered a new administration
password, confirm the new password here.
12. Adjust Time (hrs:min:sec): Check this box if you want to adjust the
current system time. When the box is checked, the time fields become
active. Enter the revised time (hours, minutes, seconds, am/pm) in the
corresponding fields. If you don’t want to adjust the current time, this box
should be left unchecked (default).
13. Adjust Date (day/month/year): Check this box if you want to adjust the
current system date. When the box is checked, the date fields become
active. Enter the revised date (day, month, year) in the corresponding
fields. If you don’t want to adjust the current date, this box should be left
unchecked (default).
14. Auto Adjust Daylight Savings: Check this box if you want the system to
adjust for daylight savings automatically, otherwise leave this box
unchecked (default).
15. Time Zone: Select a time zone
from the choices available in the
pull-down list.
Figure 37. WMI: Time Zones
58
Installing the Xirrus Array
Wireless LAN Array
16. Use NTP (IP Address): Check this box if you want to use an NTP
(Network Time Protocol) server to synchronize the Array’s clock. This
ensures that syslog time-stamping is maintained across all units. Without
an NTP server assigned (no universal clock), each Array will use its own
internal clock and stamp times accordingly, which may result in
discrepancies. When this box is checked, the NTP and NTP 2 IP address
fields become active. If you don’t want to use an NTP server, leave this
box unchecked (default), otherwise enter the IP address or DNS name of
the NTP server.
NTP enabled
Figure 38. Enabling the NTP Feature
a.
NTP 2 (IP Address): If you enabled the NTP option and the site is
using a secondary NTP server, enter the IP address or DNS name of
the secondary NTP server.
17. Click on the Apply button to apply the new settings to this session
18. Click on the Save button to save your changes (otherwise your new
settings will not take effect).
This ends the Express Setup procedure.
Installing the Xirrus Array
59
Wireless LAN Array
Installing the XS-3900 Wall Mount Assembly
The wall mounting assembly is used to mount the XS-3900 Wireless LAN Array
on a wall, instead of the traditional ceiling mount—where mounting the Array on
the ceiling may be impractical at your location.
Kit Contents
The Wall Mounting Assembly kit includes the following items:
8 x SNAPTOGGLE™ toggle bolts (for attaching the wall bracket to the
wall)
4 x 1/4 inch bolt assemblies (for attaching the mounting plate to the wall
bracket)
Wall Mounting Bracket
Tools Required
60
Power drill
1/2 inch (13mm) drill bit
Cross head screwdriver
1/4 inch nut wrench
Pencil
Level
Installing the Xirrus Array
Wireless LAN Array
Mark the Wall Position
1.
Use the Wall Mounting Bracket as a template and mark the locations on
the wall for the mounting holes.
Mark holes (at least 5 places)
Figure 39. Wall Mount—Marking the Holes
When marking the holes, ensure that the mounting plate is level—you
may need assistance.
The bracket must be secured to the wall in at least 5 places, using a minimum
of the top 3 holes and the 2 outside holes at the bottom. For maximum strength,
use all 8 mounting points (8 toggle bolts are provided).
Installing the Xirrus Array
61
Wireless LAN Array
Install the SNAPTOGGLE™ Toggle Bolts
2.
At the locations you marked in Step 1, drill a 1/2 inch (13mm) hole (there
must be a minimum clearance behind the wall of 1 7/8 inches (48mm).
3.
(Refer to graphic A) Hold the metal channel flat alongside the plastic
straps and slide the channel through the hole.
Figure 40. Installing the Toggle Bolts
4.
(Refer to graphic B) Hold the strap handle between your thumb and
forefinger and pull towards you until the metal channel rests flush
behind the wall.
To achieve the maximum shear holding capability for the toggle bolt, orient the
metal channel so that the channel is vertical to the floor.
Using your other hand, now slide the plastic cap along the straps until the
flange of the cap is flush with wall.
The straps provide a one-way ratcheting mechanism (similar to a cable tie).
Ensure that the toggle bolt assembly is oriented correctly (vertical to the floor)
before sliding the plastic cap along the straps.
5.
62
(Refer to graphic C) Break the straps at the wall, flush with the flange of
the cap. The straps can be broken by pushing them from side-to-side and
simply snapping them off.
Installing the Xirrus Array
Wireless LAN Array
Graphic D shows a cutaway example of how the toggle bolt is used to
secure an item to the wall (in our case, the item is the Wall Mounting
Bracket—secured to the wall with a minimum of 5 toggle bolts.
Do not attach the Wall Mounting Bracket to the wall at this time.
Attach the Mounting Plate to the Wall Mounting Bracket
Secure the Wireless LAN Array’s mounting plate to the Wall Mounting
Bracket (4 places)—tighten the 4 bolt assemblies to a torque of 10–12 lbf.ft
(1.38–1.66 kgf.m). Do not overtighten the bolts.
Mounting Plate
Secure (x4 bolt assemblies)
Figure 41. Attaching the Wall Mounting Plate
Attach the Wall Mounting Bracket/Plate Assembly to the Wall
6.
Secure the Wall Mounting Bracket (with attached Mounting Plate) to the
wall at the toggle bolt anchors you created in Steps 2 through 5—a
minimum of 5 places.
Installing the Xirrus Array
63
Wireless LAN Array
Mount the Array
The image opposite shows the orientation of the Wireless LAN Array when
mounted on a wall. It is not intended to show a fully installed Array.
7.
Mount the Wireless LAN Array to the Wall Mounting Bracket in the same
way that you would mount the Array to a ceiling mount (the procedure is
identical).
Figure 42. Mounting the Array on a Wall
64
Installing the Xirrus Array
Wireless LAN Array
The Web Management Interface
This chapter provides an overview of the XS-3900’s embedded Web Management
Interface (WMI), used for establishing your network’s configuration settings and
wireless operating parameters.
An Overview
The WMI is an easy-to-use graphical interface to your Xirrus Array. It allows you
to configure the product to suit your individual requirements and ensure that the
unit functions efficiently and effectively.
Figure 43. Web Management Interface
The Web Management Interface
65
Wireless LAN Array
Content
The content of the WMI has been organized by function and hierarchy, shown
here in list form. You can click on any item in the list to jump to the referenced
destination.
Array Status
Express Setup
Network Interfaces
Network Settings
Network Statistics
DHCP Settings
DNS Settings
IAP Interfaces
IAP Settings
Global Settings
Global Settings .11a
Global Settings .11bg
IAP LED Settings
Statistics
(Individual IAP Statistics)
SSID
SSID Management
Security
Security Management
Radius Server
Radius User
MAC Access List
Admin Management
Rogue AP List
Rogue Control List
Stations
Services
Time Settings
System Log
SNMP
Array Info
Tools
Show Config
Event Log
66
The Web Management Interface
Wireless LAN Array
Structure
The WMI has been designed with simplicity in mind, making navigation quick
and easy. In the following example, you’ll see that pages are divided into left and
right frames. The left frame contains configuration elements organized by
function (for example, radio interfaces, security, etc.), and where these functions
are sub-divided there is an associated pull-down menu. Also included in the left
frame are three counters that provide a running total of messages generated by
the syslog subsystem during your session—organized into Critical, Warning and
Event messages.
Left frame
Right frame
Message counters
Pull-down menu
Figure 44. WMI: Frames
The right frame contains the configuration parameters for the Array. This is
where you input data (if you want to make changes) or review the Array’s current
status and activity.
The Web Management Interface
67
Wireless LAN Array
Status Bar
Below the configuration frames you will find a status bar containing information
about this Array, including:
Location—displays the location information assigned to the unit.
Host name—the host name assigned to this unit.
Network interface IP address—the IP address of the network interface
that is currently being used.
Also included in the status bar is a Print button and a Help button. Click on the
Print button to send a print file of the active page to your local printer, or click on
the Help button to go to the Array’s online help system.
Print button
Status information
Help button
Figure 45. WMI: Status Bar
Applying Configuration Changes
When you have defined all your settings on any WMI configuration page, you
must click on the Apply button for the changes to take effect in the current
session. Click on the Save button to write your changes (for future sessions).
Character Restrictions
When inputting strings in the WMI (for example, assigning SSIDs, host name,
password, etc.), use only common alphanumeric characters. Do not use any of the
following characters:
68
“
The Web Management Interface

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Modify Date                     : 2005:11:09 12:59:09-08:00
Create Date                     : 2005:11:09 12:58:53-08:00
Title                           : xirrus.book
Author                          : Administrator
Creator                         : FrameMaker 6.0
Producer                        : Acrobat Distiller 6.0.1 (Windows)
Page Count                      : 50
Mod Date                        : 2005:11:09 12:59:09-08:00
Creation Date                   : 2005:11:09 12:58:53-08:00
Metadata Date                   : 2005:11:09 12:59:09-08:00
Has XFA                         : No

EXIF Metadata provided by EXIF.tools