Cheng Uei Precision Industry H3 Bluetooth Headset User Manual Part II

Download:
Mirror Download [FCC.gov]
Document ID	608331
Application ID	ix6xXVd6qlRj6sLz3sSAhg==
Document Description	User Manual Part II
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	157.76kB (1972022 bits)
Date Submitted	2005-12-05 00:00:00
Date Available	2005-12-05 00:00:00
Creation Date	2005-12-05 18:05:35
Producing Software	Adobe PDF library 5.00
Document Lastmod	2005-12-05 18:05:51
Document Title	User Manual Part II
Document Creator	Adobe Illustrator 10.0

Features and
Functions Guide
H3
BluetoothÂŽ
Handsfree Headset
WEARING THE
HEADSET
TURNING HEADSET
ON/OFF
To turn your headset on, press and hold
the Call button until the indicator light
flashes. Then, release the button.
To turn your headset off, press and hold
the Call button until the indicator light
flashes rapidly and then turns off.
CHANGING FOR USE
ON OTHER EAR
2 Loop the earhook over your ear.
You can wear your H3 headset on your left or
right ear. The headset comes ready for the right
ear. To change the headset for the left ear:
If you change your headset to wear on the
other ear, you can also change the
orientation of the volume buttons.
3 Press the headset to your ear.
1 Open the earhook 90
1 Turn the headset power off.
1 Open the earhook.
degrees from the
headset.
2 Press the Call button along with the
2 Gently lift and pull the
IMPORTANT:
Be sure to first follow the
CHANGING VOLUME
BUTTON ORIENTATION
top of the earhook up
and off the upper
hinge pin. Then, pull it
away to remove it.
1 Open Earhook
Volume button you want to assign as
"volume up" button until the indicator
light flashes twice.
Call
Button
The headset power turns on.
2 Pull Earhook Up
3 Flip the headset over.
Quick Start Guide
on the reverse side
of this guide
to complete initial setup
of your H3.
4 Hook the bottom of
the earhook onto the
lower hinge pin, then
lift and pull the top of
the earhook over the
upper hinge pin.
MAKING CALLS
MAKING CALLS CONTINUED
The indicator light provides information about
your headset status.
Action
Function
Action
Make a voice dial call
Tap the Call button
and speak the
name after the tone
Toggle between two
active calls
Press and hold
the Call button
End a call
Tap the Call button
Join a 3-way call
Press and hold
both Volume buttons
Receive a call
Tap the Call button
Reject a call
Press and hold the
Call button until you
hear a beep
Put an active call on
hold or resume a call
on hold
Press and hold the
Call button until you
hear a beep
Transfer a call from the
phone to the headset
Tap the Call button
Disable or enable the
indicator light
Press and hold
both Volume
buttons for 3 to 4
seconds
Headset Indicator
Off
On (steady)
10 rapid flashes
Slow pulse
Mute or unmute a call
Tap both Volume
buttons
Quick flash
Redial last call
Press and hold the
Call button until you
hear a beep
Answer a second
incoming call
Press and hold the
Call button (places
first call on hold)
Note: Your H3 supports both Handsfree and Headset
Profiles. Accessing call functions depends upon which
profile your phone supports. See your phone's user's guide
for more information.
Note: Some features are phone/network dependent.
Volume
Buttons
Hinge Pin
INDICATOR LIGHTS
Function
Call
Button
With the Charger Plugged In
Headset Indicator
Headset Status
On (steady)
Charging
Off
Charging complete
With No Charger Plugged In
Headset Status
Power off
Pairing mode
Pairing successful
Connected
(on a call)
Standby
(not on call)
Note: After 5 minutes of inactivity, the light stops flashing to
conserve power, but the headset remains in standby mode.
AUDIO TONES
The audio tones provide information about your
headset status.
Audio Tone
Single high tone when
pressing volume button
Five rapid high tones
repeated every 60 sec.
No audio indications;
deteriorating quality
Ring tone
Single high tone
Single low tone
Dual high/low tone
Single high tone
Low to high tone
Two ascending tones
Two descending tones
Headset Status
Volume at minimum
or maximum
Low battery
Out of range
Incoming call
Pairing confirmation
Voice activation
Voice tag not
recognized
End call
Phone network
not available
Mute enabled
Mute enabled
FEDERAL COMMUNICATIONS COMMISSION
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:(1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
NOTE
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiated radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user‘s authority to operate the equipment.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 2
Creator Version                 : 10
Container Version               : 9
Creator                         : Adobe Illustrator(R) 10.0
For                             : Rick Lazier, Harbor Light Communications, Inc.
Title                           : C:\Harbor Light Communications\Projects\MOT\Work Files\H3\9498a97o\Latest\Production\9498a97o\graphics\9498a97o_Back.eps
Create Date                     : 11/2/2005 8:14 PM
Bounding Box                    : -55 -649 1129 54
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:456c6272-b87d-4f29-ae3b-1c0bd8515866
Modify Date                     : 2005:12:05 18:05:51+08:00
Metadata Date                   : 2005:12:05 18:05:51+08:00
Document ID                     : uuid:08834edf-67e3-4dbe-ad4d-781df3cb5840
Format                          : application/pdf
Producer                        : Adobe PDF library 5.00

EXIF Metadata provided by EXIF.tools