Cisco Systems TG2050 802.11 a/b/g/n AP Module User Manual Host manual part 1

Cisco Systems Inc 802.11 a/b/g/n AP Module Host manual part 1

Host manual part 1

Americas Headquarters:Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USARegulatory Compliance and Safety Information for Cisco 800 Series RoutersThis document provides international regulatory and safety compliance information for Cisco 800 series routers. Use this document with the other publications for the Cisco 800 series router you have purchased.This document contains the following sections: •Product Scope, page 1 •Electromagnetic Compatibility, page 7 •EMC Class A, page 7 •Telecommunications, page 10 •Radio, page 12 •Declarations of Conformity, page 18 •CE Marking, page 18 •European Union Statements, page 19 •Environmental Compliance, page 19 •Translated Safety Warnings, page 19 •Obtaining Documentation and Submitting a Service Request, page 86Product ScopeThis section describes the Cisco product models addressed in this document. Table 1 indicates the product model numbers and the following additional information: •Product classification •EMC class information •Wireless standard •Option of outdoor antennaDraft - Not Final Version
2Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 Product ScopeTa b l e 1 Cisco Product Models Addressed in this DocumentModelsProduct Classification EMC ClassWireless StandardOption of Outdoor Antenna1.C812G+7-K9 BNone No2.C819G-4G-A-K9 BNone Yes3.C819G-4G-G-K9 BNone Yes4.C819G-4G-V-K9 BNone Yes5.C819G+7-K9 M2M BNone No6.C819G-B-K9 M2M BNone No7.C812G-CIFI+7-E-K9 B2.4 GHz, 5 GHz No8.C812G-CIFI+7-N-K9 B2.4 GHz, 5 GHz No9.C812G-CIFI-S-A-K9 B2.4 GHz, 5 GHz No10.C812G-CIFI-V-A-K9 B2.4 GHz, 5 GHz No11.C819G-S-K9 M2M BNone No12.C819G-U-K9 M2M BNone No13.C819G-V-K9 M2M BNone No14.C819H-K9 BNone No15.C819HG-4G-A-K9 BNone Yes16.C819HG-4G-G-K9 BNone Yes17.C819HG-4G-V-K9 BNone Yes18.C819HG+7-K9 M2M BNone Yes19.C819HG-B-K9 M2M BNone Yes20.C819HG-S-K9 M2M BNone Yes21.C819HG-U-K9 M2M BNone Yes22.C819HG-V-K9 M2M BNone Yes23.C819HGW+7-A-A-K9 B2.4 GHz, 5 GHz Yes24.C819HGW+7-E-K9 B2.4 GHz, 5 GHz Yes25.C819HGW+7-N-K9 B2.4 GHz, 5 GHz Yes26.C819HGW-S-A-K9 B2.4 GHz, 5 GHz Yes27.C819HGW-V-A-K9 B2.4 GHz, 5 GHz YesDraft - Not Final Version
3Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 Product Scope28.C819HWD-A-K9 B2.4 GHz, 5 GHz Yes29.C819HWD-E-K9 B2.4 GHz, 5 GHz Yes30.C866VAE-W-E-K9 Multimode DSL B2.4 GHz, 5 GHz No31.C867VAE-POE-W-A-K9 Multimode DSL B2.4 GHz, 5 GHz No32.C867VAE-W-A-K9 Multimode DSL B2.4 GHz, 5 GHz No33.C867VAE-W-E-K9 Multimode DSL B2.4 GHz, 5 GHz No34.C881-V-K9 Voice BNone No35.C881G+7-A-K9 Ethernet BNone No36.C881G+7-K9 Ethernet BNone No37.C881G-B-K9 Ethernet BNone No38.C881G-S-K9 Ethernet BNone No39.C881G-U-K9 Ethernet BNone No40.C881G-V-K9 Ethernet BNone No41.C881SRST-K9 Ethernet BNone No42.C881SRSTW-GN-A-K9 Ethernet B2.4 GHz No43.C881SRSTW-GN-E-K9 Ethernet B2.4 GHz No44.C881W-A-K9 Ethernet B2.4 GHz No45.C881W-E-K9 Ethernet B2.4 GHz No46.C881W-P-K9 Ethernet B2.4 GHz No47.C881WD-A-K9 Ethernet B2.4 GHz, 5 GHz No48.C881WD-E-K9 Ethernet B2.4 GHz, 5 GHz No49.C886VA-W-E-K9 Multimode DSL A2.4 GHz No50.C886VAG+7-K9 Multimode DSL ANone No51.C887VA-V-K9 Vo ic e ANone No52.C887VA-V-K9 Multimode DSL ANone No53.C887VA-V-W-E-K9 Multimode DSL A2.4 GHz NoTable 1 Cisco Product Models Addressed in this DocumentModelsProduct Classification EMC ClassWireless StandardOption of Outdoor AntennaDraft - Not Final Version
4Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 Product Scope54.C887VA-W-A-K9 Multimode DSL A2.4 GHz No55.C887VA-W-E-K9 Multimode DSL A2.4 GHz No56.C887VA-WD-A-K9 Multimode DSL A2.4 GHz, 5 GHz No57.C887VA-WD-E-K9 Multimode DSL A2.4 GHz, 5 GHz No58.C887VAG+7-K9 Multimode DSL ANone No59.C887VAG-S-K9 Multimode DSL ANone No60.C887VAGW+7-A-K9 Multimode DSL A2.4 GHz, 5 GHz No61.C887VAGW+7-E-K9 Multimode DSL A2.4 GHz, 5 GHz No62.C887VAMG+7-K9 Multimode DSL ANone No63.C888EA-K9 SHDSL ANone No64.C888EG+7-K9 SHDSL ANone No65.C888ESRST-K9 SHDSL ANone No66.C888ESRSTW-GNA-K9 SHDSL A2.4 GHz No67.C888ESRSTW-GNE-K9 SHDSL A2.4 GHz No68.C888SRST-K9 SHDSL ANone No69.C888SRSTW-GN-A-K9 SHDSL A2.4 GHz No70.C888SRSTW-GN-E-K9 SHDSL A2.4 GHz No71.C892FSP-K9 BNone No72.C896VA BNone No73.C897VA Multimode DSL BNone No74.C897VA-M Multimode DSL BNone No75.C897VAM-W Multimode DSL B2.4 GHz, 5 GHz No76.C897VAW Multimode DSL B2.4 GHz, 5 GHz No77.C898EA SHDSL ANone No78.CISCO861-K9 Ethernet BNone No79.CISCO861-PCI-K9 Ethernet BNone NoTable 1 Cisco Product Models Addressed in this DocumentModelsProduct Classification EMC ClassWireless StandardOption of Outdoor AntennaDraft - Not Final Version
5Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 Product Scope80.CISCO861W-GN-A-K9 Ethernet B2.4 GHz No81.CISCO861W-GN-E-K9 Ethernet B2.4 GHz No82.CISCO861W-GN-P-K9 Ethernet B2.4 GHz No83.CISCO866VAE Multimode DSL BNone No84.CISCO866VAE-K9 Multimode DSL BNone No85.CISCO867VAE Multimode DSL BNone No86.CISCO867VAE-K9 Multimode DSL BNone No87.CISCO881-K9 Ethernet BNone No88.CISCO881-PCI-K9 Ethernet BNone No89.CISCO881-SEC-K9 Ethernet BNone No90.CISCO881C-K9 Ethernet BNone No91.CISCO881C-W-E-K9 Ethernet B2.4 GHz No92.CISCO881G-K9 Ethernet BNone No93.CISCO881GC-K9 Ethernet BNone No94.CISCO881GC-W-E-K9 Ethernet B2.4 GHz No95.CISCO881GW-GN-A-K9 Ethernet B2.4 GHz, 5 GHz No96.CISCO881GW-GN-E-K9 Ethernet B2.4 GHz, 5 GHz No97.CISCO881W-GN-A-K9 Ethernet B2.4 GHz No98.CISCO881W-GN-E-K9 Ethernet B2.4 GHz No99.CISCO881W-GN-P-K9 Ethernet B2.4 GHz, 5 GHz No100.CISCO886VA-J-K9 Multimode DSL ANone No101.CISCO886VA-K9 Multimode DSL ANone No102.CISCO886VA-SEC-K9 Multimode DSL ANone No103.CISCO887V-K9 Multimode DSL ANone No104.CISCO887V-SEC-K9 Multimode DSL ANone No105.CISCO887VA-K9 Multimode DSL ANone NoTable 1 Cisco Product Models Addressed in this DocumentModelsProduct Classification EMC ClassWireless StandardOption of Outdoor AntennaDraft - Not Final Version
6Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 Product Scope106.CISCO887VA-M-K9 Multimode DSL ANone No107.CISCO887VA-SEC-K9 Multimode DSL ANone No108.CISCO887VG-K9 Multimode DSL ANone No109.CISCO887VGW-GNA-K9 VDSL A2.4 GHz No110.CISCO887VGW-GNE-K9 VDSL A2.4 GHz No111.CISCO887VW-GNA-K9 Multimode DSL A2.4 GHz No112.CISCO887VW-GNE-K9 Multimode DSL A2.4 GHz No113.CISCO888-K9 SHDSL ANone No114.CISCO888-SEC-K9 SHDSL ANone No115.CISCO888E-K9 SHDSL ANone No116.CISCO888EW-GNA-K9 SHDSL A2.4 GHz No117.CISCO888EW-GNE-K9 SHDSL A2.4 GHz No118.CISCO888G-K9 SHDSL ANone No119.CISCO888GW-GN-A-K9 SHDSL A2.4 GHz No120.CISCO888GW-GN-E-K9 SHDSL A2.4 GHz No121.CISCO888W-GN-A-K9 SHDSL A2.4 GHz No122.CISCO888W-GN-E-K9 SHDSL A2.4 GHz No123.CISCO891-K9 Ethernet BNone No124.CISCO891-PCI-K9 Ethernet BNone No125.CISCO891C-K9 Ethernet BNone No126.CISCO891C-W-C-K9 Ethernet B2.4 GHz, 5 GHz No127.CISCO891W-AGN-A-K9 Ethernet B2.4 GHz, 5 GHz No128.CISCO891W-AGN-C-K9 Ethernet B2.4 GHz, 5 GHz No129.CISCO891W-AGN-N-K9 Ethernet B2.4 GHz, 5 GHz No130.CISCO892-K9 Ethernet BNone No131.CISCO892C-K9 Ethernet BNone No132.CISCO892C-W-C-K9 Ethernet B2.4 GHz, 5 GHz No133.CISCO892F-K9 Ethernet BNone NoTable 1 Cisco Product Models Addressed in this DocumentModelsProduct Classification EMC ClassWireless StandardOption of Outdoor AntennaDraft - Not Final Version
7Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 Electromagnetic CompatibilityElectromagnetic CompatibilityThis section describes electromagnetic compatibility (EMC) compliance conditions. It contains the following: •EMC Class A •EMC Class BEMC Class AThis section includes the following EMC Class A warnings: •Statement 2017—Class A Notice for FCC •CISPR 22 Class A Statement •Statement 2021—Class A Notice for Canada •Statement 191—VCCI Class A Warning for JapanStatement 2017—Class A Notice for FCCModifying the equipment without Cisco's authorization may result in the equipment no longer complying with FCC requirements for Class A or Class B digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television communications at your own expense.This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.134.CISCO892FW-A-K9 Ethernet B2.4 GHz, 5 GHz No135.CISCO892FW-E-K9 Ethernet B2.4 GHz, 5 GHz No136.CISCO892J-K9 Ethernet ANone No137.CISCO892W-AGN-E-K9 Ethernet B2.4 GHz, 5 GHz No138.CISCO892W-AGN-P-K9 Ethernet B2.4 GHz, 5 GHz NoTable 1 Cisco Product Models Addressed in this DocumentModelsProduct Classification EMC ClassWireless StandardOption of Outdoor AntennaDraft - Not Final Version
8Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 Electromagnetic CompatibilityCISPR 22 Class A StatementThis equipment complies with the requirements of CISPR 22 (EN 55022) for Class A Information Technology Equipment (ITE). WarningThis is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.Statement 2021—Class A Notice for CanadaThis Class A digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.Statement 191—VCCI Class A Warning for JapanEMC Class BStatement 2018—Class B Notice for FCCModifying the equipment without Cisco’s authorization may result in the equipment no longer complying with FCC requirements for Class B digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television communications at your own expense.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular WarningThis is a Class A product based on the standard of the VCCI Council. If this equipment is used in a domestic environment, radio interference may occur, in which case, the user may be required to take corrective actions.VCCI-ADraft - Not Final Version
9Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 Electromagnetic Compatibilityinstallation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: •Reorient or relocate the receiving antenna. •Increase the separation between the equipment and receiver. •Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. •Consult the dealer or an experienced radio/TV technician for help.CISPR 22 Class B StatementEmissions:This equipment complies with the requirements of CISPR 22 (EN 55022) for Class B Information Technology Equipment (ITE).Canada Compliance StatementsStatement 2022—Class B Notice for CanadaThis Class B digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.Industry Canada NoticeThis equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is confirmed by the registration number. The abbreviation, IC, before the registration number signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not imply that Industry Canada approved the equipment.The Ringer Equivalence Number (REN) for this terminal equipment is 01. The REN assigned to each terminal equipment provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed five.Le présent matériel est conforme aux spécifications techniques applicables d'Industrie Canada. Cette conformité est confirmée par le numéro d'enregistrement. Le sigle IC, placé devant le numéro d'enregistrement, signifie que l’enregistrement s’est effectué conformément à une déclaration de conformité et indique que les spécifications techniques d'Industrie Canada ont été respectées. Il n’implique pas qu’Industrie Canada a approuvé le matériel. L'indice d'équivalence de la sonnerie (IES) du présent matériel est de 01. L'IESassigné à chaque dispositif terminal indique le nombre maximal de terminaux qui peuvent êtreraccordés à une interface téléphonique. La terminaison d'une interface peut consister en unecombinaison quelconque de dispositifs, à la seule condition que la somme d'indicesd'équivalence de la sonnerie de tous les dispositifs n'excède pas 5.Draft - Not Final Version
10Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 TelecommunicationsAustralia Compliance StatementNetwork connected equipment is approved to the Australian and New Zealand Safety and EMC requirements by Cisco Systems Incorporated which is a Recognized Laboratory by ACA and New Zealand. Stand-alone power supply modules provided with this equipment are separately approved by an Australian State designated Electricity Authority.Statement 157—VCCI Compliance for Class B EquipmentTelecommunicationsThis section describes telecommunications compliance. It contains the following: •Statement 3023—Equipment That Complies With 47 CFR Part 68Statement 3023—Equipment That Complies With 47 CFR Part 68This equipment complies with Part 68 of the FCC rules and the requirements adopted by ACTA. On the bottom of the equipment is a label that contains, among other information, a product identifier in the format, US:AAAAANNAAAAAAA. If requested, this number must be provided to the telephone company.Applicable connector jack Universal Service Order Codes (“USOC”) for the Equipment is RJ11.A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details.The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone WarningThis is a Class B product based on the standard of the VCCI Council. If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual. VCCI-BDraft - Not Final Version
11Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 Telecommunicationscompany. For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format US:AAAAANNAAAAAAA. The digits represented by 01 are the REN without a decimal point.If this Router (Cisco 860VAE) causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. If advance notice is not practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.The telephone company may make changes in its facilities, equipment, operation, or procedures that could affect the operation of this equipment. If this happens, the telephone company will provide advance notice in order for you to make the necessary modifications to maintain uninterrupted service.If trouble is experienced with this Router (Cisco 860VAE), for repair or warranty information, please contact Cisco Systems, Inc. – address: 170 West Tasman Dr. San Jose, CA95134 USA, phone number: 1 408 526 4000. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved.Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information.If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer.WHEN PROGRAMMING EMERGENCY NUMBERS AND/OR MAKING TEST CALLS TO EMERGENCY NUMBERS:1.Remain on the line and briefly explain to the dispatcher the reason for the call.2.Perform such activities in the off-peak hours, such as early morning or late evenings.The facility interface and service order codes for the Cisco 800 series routers are shown in Table 2. Cisco 800 series and SOHO series routers bearing labeling identification number US:5B1MFNA0013 or US:5B1DLO1B0144, and Cisco 860 and 880 router models bearing labeling identification number US:5B1ISO1B0247 comply with the following requirement: •FCC Rules and Regulations 47 CFR Part 68 •TIA-968-A, Technical Criteria for Terminal Equipment to Prevent Harm to the Telephone Network, July 2002, as adopted by the Administrative Council on Terminal Attachments (ACTA).Ta b l e 2 Cisco 800 Series Routers Facility Interface and Service Order CodesPort TypeFacility Interface CodeService Order Code Jack TypeISDN BRI S/T 02IS5 6.0N RJ-49CISDN BRI U 02IS5 6.0N RJ-49CDSU 56K 04DU5-56 6.0N RJ-48SADSL Metallic —RJ-11CSHDSL Metallic —RJ-14CFXO 02LS2 None RJ-11CFXO 02GS2 None RJ-21XDID 02RV2.T AS.2 RJ-11CAnalog Modem 02LS2 None RJ-11CDraft - Not Final Version
12Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 RadioCisco 801, 802, 803, 804, 805, 806, 811, 813, 815, 826, 827, 828, 831, 836, 837, 851, 856, 857, 858, 871, 877, 878, 881-V, and 887VA-V routers, and Cisco SOHO 76, 77, 78, 91, 96, and 97 routers bearing labeling identification number US:5BMFMAM0013 or US:5B1DLO1B0144, and IAD881F, IAD881B, C881SRST, 888, 888G, IAD888F, IAD888B, C888SRST, routers bearing labeling identification number US:5B1IS01B0247, and Cisco 891, 892 routers bearing labeling identification number US:5B1IS01B0268 comply with the following requirement: •FCC Rules and Regulations 47 CFR Part 68 •TIA-968-A, Technical Criteria for Terminal Equipment to Prevent Harm to the Telephone Network, 2002, as adopted by the Administrative Council on Terminal Attachments (ACTA).Cisco’s Supplier Declarations of Conformity are available online at:http://wwwin-tools.cisco.com/cse/prdapp/jsp/ExternalSearch.jsp?selNavObjId=search|extSearchRadioThis section describes radio compliance conditions. It contains the following: •Power Level Settings •Canadian Compliance Statement •Statement 287—Declaration of Conformity to R&TTE Directive 1999/5/EC for the European Community, Switzerland, Norway, Iceland and Liechtenstein •RF Exposure •Statement 372—Wireless LAN Products •Statement 391—Low-Power Radio Data Communications Systems (ARIB-STD) •Administrative Rules for Cisco Wireless Devices in TaiwanRadio: CautionsCautionThe Part 15 radio device operates on a non-interference basis with other devices operating at this frequency when using the integrated antennas. Any changes or modification to the product not expressly approved by Cisco could void the user’s authority to operate this device.Draft - Not Final Version
13Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 RadioRadio: Statements and Additional InformationNoteThis equipment is intended to be used in all EU and EFTA countries. Outdoor use may be restricted to certain frequencies and/or may require a license for operation. For more details, contact Cisco Corporate Compliance.Cautions Relevant to 5 GHz RadioStatement 372—Wireless LAN ProductsAll wireless LAN products in the 5.2/5.3GHz band cannot be used outdoors. Use the product only indoors.Indoor OperationCautionThis device operates in the 5150 to 5250 MHz and 5470 to 5725 MHz bands and is therefore restricted to indoor operation only per FCC guidance. The use of this system outside is in non compliance of the FCC regulations and guidelines. Please contact your Cisco sales person for further detail.Power Level SettingsTable 3 lists the maximum power level settings permissible for the radio modules.Canadian Compliance StatementThis Class B Digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment Regulations.Ta b l e 3 Maximum Rated Power Output for the RadiosRadio FCC IDMaximum Power Setting (dBM)802.11a 802.11b (2.4 GHz) 802.11g (2.4 GHz) 802.11n (2.4, 5 GHz)LDKXSNIACG13 —19 17 —MCL74487504 —17 15 16MCL74487604 16 17 15 15LDKTG2050 15 17 15 16MCL74751901 —17 15 16 (2.4 GHz only)Draft - Not Final Version
14Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 RadioCet appareil numerique de la classe B respecte les exigences du Reglement sur le material broilleur du Canada.This device complies with Class B Limits of Industry Canada. Operation is subject to the following two conditions: •This device may not cause harmful interference. •This device must accept any interference received, including interference that may cause undesired operation.Cisco 2.4-GHz and 5-GHz Access Points are certified to the requirements of RSS-210 for 2.4-GHz spread spectrum devices. The use of this device in a system operating either partially or completely outdoors may require the user to obtain a license for the system according to the Canadian regulations. For further information, contact your local Industry Canada office.Statement 287—Declaration of Conformity to R&TTE Directive 1999/5/EC for the European Community, Switzerland, Norway, Iceland and LiechtensteinThis section contains compliance information relevant to the European Union and other countries that have implemented the EU Directive 1999/5/EC.The information contained in this section applies to the following wireless LAN products:English:This equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.[Bulgarian]: [Czech]: Dansk [Danish]:Dette udstyr er i overensstemmelse med de væsentlige krav og andre relevante bestemmelser i Direktiv 1999/5/EF.Deutsch [German]:Dieses Gerät entspricht den grundlegenden Anforderungen und den weiteren entsprechenden Vorgaben der Richtlinie 1999/5/EU.Eesti [Estonian]: See seade vastab direktiivi 1999/5/EÜ olulistele nõuetele ja teistele asjakohastele sätetele.Español [Spanish]:Este equipo cumple con los requisitos esenciales asi como con otras disposiciones de la Directiva 1999/5/CE.[Greek]: Français [French]:Cet appareil est conforme aux exigences essentielles et aux autres dispositions pertinentes de la Directive 1999/5/EC.Íslenska [Icelandic]:Þetta tæki er samkvæmt grunnkröfum og öðrum viðeigandi ákvæðum Tilskipunar 1999/5/EC.Draft - Not Final Version
15Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 RadioRF ExposureThe radio has been found to be compliant to the requirements set forth in CFR 47 Sections 2.1091, and 15.247 (b) (4) addressing RF Exposure from radio frequency devices as defined in Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields. The equipment should be installed more than 20 cm (7.9 in.) from your body or nearby persons. The access Italiano [Italian]:Questo apparato é conforme ai requisiti essenziali ed agli altri principi sanciti dalla Direttiva 1999/5/CE.Latviski [Latvian]: [Lithuanian]: Nederlands [Dutch]:Dit apparaat voldoet aan de essentiele eisen en andere van toepassing zijnde bepalingen van de Richtlijn 1999/5/EC.Malti [Maltese]: Magyar [Hungarian]: Norsk [Norwegian]:Dette utstyret er i samsvar med de grunnleggende krav og andre relevante bestemmelser i EU-direktiv 1999/5/EF.Polski [Polish]: Português [Portuguese]:Este equipamento está em conformidade com os requisitos essenciais e outras provisões relevantes da Directiva 1999/5/EC.[Romanian]: Acest echipament este in conformitate cu cerintele esentiale si cu alte prevederi relevante ale Directivei 1999/5/EC.Slovensko [Slovenian]: Ta naprava je skladna z bistvenimi zahtevami in ostalimi relevantnimi pogoji Direktive 1999/5/EC.Slovensky [Slovak]: Toto zariadenie je v zhode so základnými požiadavkami a inými príslušnými nariadeniami direktív: 1999/5/EC. Suomi [Finnish]: Svenska [Swedish]: Draft - Not Final Version
16Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 Radiopoint must be installed to maintain a minimum 20 cm (7.9 in.) co-located separation distance from other FCC approved indoor/outdoor antennas used with the access point. Any antennas or transmitters not approved by the FCC cannot be co-located with the access point. The access point’s co-located 2.4 GHz integrated antennas support a minimum separation distance of 8 cm (3.2 in.) and are compliant with the applicable FCC RF exposure limit when transmitting simultaneously.NoteDual antennas used for diversity operation are not considered co-located.Statement 391—Low-Power Radio Data Communications Systems (ARIB-STD)This equipment shares a frequency band with a wide range of equipment: e.g. industrial, scientific, and medical equipment such as microwave ovens, premises radio station (radio stations requiring licenses), and specified low-power radio stations (radio stations not requiring licenses) for RFID used for factory production lines as well as amateur radio stations (radio stations requiring licenses).1.Before use, confirm that no premises radio stations and specified low-power radio stations for RFID or amateur radio stations operate in your vicinity.2.In the event that this equipment causes harmful interference to any premises radio station for RFID, immediately change frequencies or halt radio wave emission and contact us at the information indicated below for consultation on interference avoidance measures (e.g. partition installation).3.Contact us at the information indicated below URL if this equipment causes harmful interference to any specified low-power radio stations for RFID or amateur radio stations or if other problems arise.Contact us at: http://www.cisco.com/jp/Administrative Rules for Cisco Wireless Devices in TaiwanThis section provides administrative rules for operating Cisco wireless access products in Taiwan. The rules are provided in both Chinese and English.Wireless Devices with IEEE 802.11a/b/g Radios This equipment is limited for indoor use.Draft - Not Final Version
17Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 RadioStatement 392—Device is Prohibited for Outdoor Operations Within the 5.25–5.35 GHz BandTo avoid radio interference, this device is prohibited for outdoor operations within the 5.25–5.35 GHz band. (for unit covers 5.25–5.35 GHz, on both unit and manual)Administrative Rules for Low-power Radio-frequency Devices (for all wireless unit, on manual)Article 12 For those low-power radio-frequency devices that have already received a type-approval, companies, business units or users should not change its frequencies, increase its power or change its original features and functions.Article 14 The operation of the Low-power Radio-frequency Devices is subject to the conditions that no harmful interference is caused to aviation safety and authorised radio station; and if interference is caused, the user must stop operating the device immediately and can’t re-operate it until the harmful interference is clear.The authorised radio station means a radio-communication service operating in accordance with COMMUNICATION ACT.The operation of the Low-power Radio-frequency Devices is subject to the interference caused by the operation of an authorised radio station, by another intentional or unintentional radiator, by industrial, scientific and medical (ISM) equipment, or by an incidental radiator.Low-power Radio-frequency Devices Technical Specifications (for unit covers 5.25–5.35 GHz, on manual)4.7 Unlicensed National Information Infrastructure4.7.5 Within the 5.25–5.35 GHz band, U-NII devices will be restricted to indoor operations to reduce any potential for harmful interference to co-channel MSS operations.4.7.6 The U-NII devices shall accept any interference from legal communications and shall not interfere the legal communications. If interference is caused, the user must stop operating the device immediately and can’t re-operate it until the harmful interference is clear.4.7.7 Manufacturers of U-NII devices are responsible for ensuring frequency stability such that an emissionis maintained within the band of operation under all conditions of normal operation as specified in the user manual.Draft - Not Final Version
18Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 Declarations of ConformityDeclarations of ConformityThe Declaration of Conformity statements for this product can be found at the following URL:http://www.ciscofax.comNoteIf you still have questions regarding the compliance of these products or you cannot find the information you are looking for, please send an e-mail request to complianceinfo@cisco.com.CE MarkingThis product bears the CE mark in conformance with Annex VII of Directive 1999/5/CE. The following CE mark and class-2 identifier is affixed to the equipment and packaging:Draft - Not Final Version
19Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 European Union StatementsEuropean Union StatementsThe following statements apply in the European Union (EU). •Network Termination Point Statement •ISDN S/T Ports StatementNetwork Termination Point StatementThis product does not contain a “Network Termination Point” (NTP) as defined by ETSI 300 386-2. This product is classified by the manufacturer as “Terminal Equipment.” If you have any additional questions, please contact your local network operator.ISDN S/T Ports StatementThese ports have not been classified as “directly connected ports” to outside cables as defined by CISPR 24, 1997 by the manufacturer. If you have any additional questions, please contact your local network operator.Environmental ComplianceThe following statement(s) address environmental compliance. •Statement 6005—California Perchlorate Contamination Prevention Act (Title 22, California Code of Regulations, Chapter 33)Statement 6005—California Perchlorate Contamination Prevention Act (Title 22, California Code of Regulations, Chapter 33)The battery inside this product might contain perchlorate, a known hazardous substance, so special handling and disposal of this product might be necessary. For more information about perchlorate and best management practices for perchlorate-containing substances, see http://www.dtsc.ca.gov/HazardousWaste/Perchlorate/index.cfm.Translated Safety WarningsThis section contains the translations of the following warning statements. A warning means danger. You are in a situation that could cause bodily injury. Before working on equipment, be aware of the hazards involved with electrical circuitry and standard safety practices to prevent accidents. •Statement 1071—Warning Definition •Statement 19—TN Power Warning •Statement 23—ISDN Connection Warning •Statement 43—Jewelry Removal WarningDraft - Not Final Version
20Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 Translated Safety Warnings •Statement 94—Wrist Strap Warning •Statement 119—Unit Short Circuit Protection •Statement 150—Power Off Before Working on System •Statement 151—ISDN Network Voltages Warning •Statement 162—EU Public Network Port Warning •Statement 199—Emergency Access Warning •Statement 242—Equipment Grounding Warning •Statement 332—Antenna Installation Warning •Statement 353—This Product Must be Connected •Statement 371—Power Cable and AC Adapter •Statement 373—Must Connect To An Indoor Antenna •Statement 378—Read Wall-Mounting Instructions Before Installation •Statement 393—Explosive Device Proximity Wireless Network Device •Statement 1004—Installation Instructions •Statement 1005—Circuit Breaker •Statement 1008—Class 1 Laser Product •Statement 1010—Staring into Laser Beam •Statement 1015—Battery Handling •Statement 1016—Invisible Laser Radiation •Statement 1021—SELV Circuit •Statement 1023—No. 26 AWG •Statement 1024—Ground Conductor •Statement 1025—Use Copper Conductors Only •Statement 1026—WAN Port Static Shock •Statement 1028—More Than One Power Supply •Statement 1030—Equipment Installation •Statement 1031—EU Public Network Port •Statement 1033—SELV-IEC 60950 DC Power Supply •Statement 1035—Proximity to Water •Statement 1036—Telephone Jacks in Wet Locations •Statement 1037—Uninsulated Wires or Terminals •Statement 1038—Telephone Use During an Electrical Storm •Statement 1040—Product Disposal •Statement 1042—Ring Signal Generator •Statement 1046—Installing or Replacing the Unit •Statement 1052—Installing and Grounding the Antenna •Statement 1056—Unterminated Fiber Cable •Statement 1057—Hazardous Radiation ExposureDraft - Not Final Version
21Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 Translated Safety Warnings •Statement 1072—Shock Hazard from Interconnections •Statement 1073—No User-Serviceable Parts •Statement 1074—Comply with Local and National Electrical Codes •Statement 1077—Do Not Operate Unit Without Covers •Statement 1088—Avoid Servicing Outdoor Connections During an Electrical StormStatement 1071—Warning DefinitionWarningIMPORTANT SAFETY INSTRUCTIONSThis warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device. SAVE THESE INSTRUCTIONSWaarschuwingBELANGRIJKE VEILIGHEIDSINSTRUCTIESDit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt raadplegen.BEWAAR DEZE INSTRUCTIESVaroitusTÄRKEITÄ TURVALLISUUSOHJEITATämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien lausuntonumeroiden avulla.SÄILYTÄ NÄMÄ OHJEETAttentionIMPORTANTES INFORMATIONS DE SÉCURITÉ Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil, référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.CONSERVEZ CES INFORMATIONSDraft - Not Final Version
22Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 Translated Safety WarningsWarnungWICHTIGE SICHERHEITSHINWEISEDieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.BEWAHREN SIE DIESE HINWEISE GUT AUF.AvvertenzaIMPORTANTI ISTRUZIONI SULLA SICUREZZA Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti. Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le traduzioni delle avvertenze riportate in questo documento. CONSERVARE QUESTE ISTRUZIONIAdvarselVIKTIGE SIKKERHETSINSTRUKSJONERDette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne enheten.TA VARE PÅ DISSE INSTRUKSJONENEAvisoINSTRUÇÕES IMPORTANTES DE SEGURANÇA Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo.GUARDE ESTAS INSTRUÇÕES ¡Advertencia!INSTRUCCIONES IMPORTANTES DE SEGURIDADEste símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña a este dispositivo. GUARDE ESTAS INSTRUCCIONESDraft - Not Final Version
23Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 Translated Safety WarningsVarning!VIKTIGA SÄKERHETSANVISNINGARDenna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada. Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna anordning.SPARA DESSA ANVISNINGARDraft - Not Final Version
24Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 Translated Safety WarningsAvisoINSTRUÇÕES IMPORTANTES DE SEGURANÇAEste símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo.GUARDE ESTAS INSTRUÇÕESAdvarselVIGTIGE SIKKERHEDSANVISNINGERDette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de oversatte advarsler, der fulgte med denne enhed.GEM DISSE ANVISNINGERDraft - Not Final Version
25Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 Translated Safety WarningsDraft - Not Final Version
26Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 Translated Safety WarningsStatement 19—TN Power WarningWarningThe device is designed to work with TN power systems.WaarschuwingHet apparaat is ontworpen om te functioneren met TN energiesystemen.VaroitusKoje on suunniteltu toimimaan TN-sähkövoimajärjestelmien yhteydessä.AttentionCe dispositif a été conçu pour fonctionner avec des systèmes d'alimentation TN.WarnungDas Gerät ist für die Verwendung mit TN-Stromsystemen ausgelegt.AvvertenzaIl dispositivo è stato progettato per l’uso con sistemi di alimentazione TN.AdvarselUtstyret er utfomet til bruk med TN-strømsystemer.Draft - Not Final Version
27Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 Translated Safety WarningsStatement 23—ISDN Connection WarningAvisoO dispositivo foi criado para operar com sistemas de corrente TN.¡Advertencia!El equipo está diseñado para trabajar con sistemas de alimentación tipo TN. Varning!Enheten är konstruerad för användning tillsammans med elkraftssystem av TN-typ.WarningThe ISDN connection is regarded as a source of voltage that should be inaccessible to user contact. Do not attempt to tamper with or open any public telephone operator (PTO)-provided equipment or connection hardware. Any hardwired connection (other than by nonremovable, connect-one-time-only plug) must be made only by PTO staff or suitably trained engineers.WaarschuwingDe verbinding met ISDN (Integrated Services Digital Network = Digitaal netwerk met geïntegreerde faciliteiten) wordt beschouwd als een spanningsbron die ontoegankelijk dient te zijn voor gebruikers. Gebruikers dienen geen poging te doen om door de openbare telefoondienst (PTT) verstrekte apparatuur of aansluitingshardware te openen of ermee te knoeien. Alle vastbedrade verbindingen (behalve die verbindingen die gemaakt zijn door een niet-verwijderbare, slechts eenmaal te verbinden stekker) dienen slechts door PTT-personeel of door daartoe opgeleide ingenieurs gemaakt te worden.VaroitusISDN-liitäntää pidetään jännitelähteenä, jonka kanssa käyttäjän ei tulisi päästä kosketuksiin. Käyttäjien ei tulisi yrittää peukaloida tai avata laitteita tai liittimiä, jotka kuuluvat yleiselle puhelinlaitokselle (PTO). Ainoastaan yleisen puhelinlaitoksen henkilökunnan tai ammattitaitoisten teknikoiden tulee tehdä kaapeliliitännät (lukuun ottamatta kiinteitä pistokkeita, jotka yhdistetään ainoastaan yhden kerran).Draft - Not Final Version
28Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 Translated Safety WarningsAttentionLa connexion du réseau numérique intégré (Integrated Services Digital Network ou ISDN) constitue une source de tension qui ne doit pas être accessible à l'utilisateur. Les utilisateurs ne doivent jamais tenter de modifier ni même d'ouvrir un matériel fourni par une compagnie de téléphone public, ou le matériel de connexion. Toute connexion câblée (autre que celles établies par une prise non démontable à connexion unique) ne doit être effectuée que par le personnel de la compagnie de téléphone ou par des techniciens proprement formés.WarnungDie ISDN-Verbindung gilt als eine Spannungsquelle, die dem Anwender unzugänglich sein sollte. Anwender sollten nicht versuchen, sich an der von den Anbietern öffentlicher TK-Dienste gelieferten Ausstattung oder Verbindungs-Hardware zu schaffen zu machen oder sie zu öffnen. Alle festverdrahteten Verbindungen (mit Ausnahme der Verbindungen mit einem nicht abnehmbaren, nur einmal anzuschließenden Stecker) sind von Mitarbeitern des TK-Anbieters oder von entsprechend geschulten Technikern herzustellen.AvvertenzaIl collegamento ISDN (Integrated Services Digital Network - Rete digitale a servizi integrati) viene considerato come una fonte di tensione che dovrebbe essere inaccessibile al contatto dell’utente. Gli utenti non devono né manomettere né provare ad aprire le apparecchiature o i dispositivi di collegamento forniti dalla società telefonica. Qualsiasi collegamento cablato (ad eccezione di una spina non rimovibile, da installare una sola volta) deve essere eseguito esclusivamente da un dipendente della società telefonica o da tecnici specializzati.AdvarselISDN-koblingen betraktes som en spenningskilde som bør være utilgjengelig for brukeren. Brukere bør ikke klusse med eller åpne utstyr eller tilkoblingsmateriale som er utstyrt av Telenor. Eventuelle faste installasjoner (bortsett fra koblinger som er foretatt med et støpsel for engangsbruk og som ikke kan fjernes) må kun utføres av Telenor-montører.AvisoA conexão RDIS (Rede Digital com Integração de Serviços) é interpretada como uma fonte de tensão que deverá ser inacessível ao utilizador. Os utilizadores não deverão tentar violar qualquer equipamento ou conexão de serviço telefónico público. Qualquer conexão de rede de fios (para além daquela estabelecida por uma ficha não-removível de ligação única), deverá apenas ser efectuada por pessoal dos serviços telefónicos ou engenheiros devidamente treinados.¡Advertencia!La conexión al circuito RDSI (Red Digital de Servicios Integrados) se considera como una fuente de voltaje con la cual el usuario no debe entrar en contacto. Los usuarios deberán evitar manipular indebidamente, o abrir, los equipos o hardware de conexión proporcionados por cualquier compañía operadora de la red pública de telefonía. Las conexiones de cable rígido que sean necesarias (excepto las de clavija no desmontable de un solo uso) deberán ser realizadas exclusivamente por personal de la entidad operadora de la red pública de telefonía, o por personal técnico adecuadamente capacitado.Varning!ISDN-anslutningen betraktas som en spänningskälla och bör inte vara åtkomlig för användaren (ISDN: Integrated Services Digital Network = digitalt flertjänstnät). Användare får inte manipulera eller söka öppna utrustning eller anslutningsdon som tillhandahållits av telefonbolag (PTO-produkter). Anslutning av ledningar (med undantag av en icke löstagbar propp för engångsanslutning) får endast utföras av PTO-anställda eller lämpligt utbildade tekniker.Draft - Not Final Version
29Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 Translated Safety WarningsStatement 43—Jewelry Removal WarningWarningBefore working on equipment that is connected to power lines, remove jewelry (including rings, necklaces, and watches). Metal objects will heat up when connected to power and ground and can cause serious burns or weld the metal object to the terminals.WaarschuwingAlvorens aan apparatuur te werken die met elektrische leidingen is verbonden, sieraden (inclusief ringen, kettingen en horloges) verwijderen. Metalen voorwerpen worden warm wanneer ze met stroom en aarde zijn verbonden, en kunnen ernstige brandwonden veroorzaken of het metalen voorwerp aan de aansluitklemmen lassen.VaroitusEnnen kuin työskentelet voimavirtajohtoihin kytkettyjen laitteiden parissa, ota pois kaikki korut (sormukset, kaulakorut ja kellot mukaan lukien). Metalliesineet kuumenevat, kun ne ovat yhteydessä sähkövirran ja maan kanssa, ja ne voivat aiheuttaa vakavia palovammoja tai hitsata metalliesineet kiinni liitäntänapoihin.AttentionAvant d’accéder à cet équipement connecté aux lignes électriques, ôter tout bijou (anneaux, colliers et montres compris). Lorsqu’ils sont branchés à l’alimentation et reliés à la terre, les objets métalliques chauffent, ce qui peut provoquer des blessures graves ou souder l’objet métallique aux bornes.WarnungVor der Arbeit an Geräten, die an das Netz angeschlossen sind, jeglichen Schmuck (einschließlich Ringe, Ketten und Uhren) abnehmen. Metallgegenstände erhitzen sich, wenn sie an das Netz und die Erde angeschlossen werden, und können schwere Verbrennungen verursachen oder an die Anschlußklemmen angeschweißt werden.AvvertenzaPrima di intervenire su apparecchiature collegate alle linee di alimentazione, togliersi qualsiasi monile (inclusi anelli, collane, braccialetti ed orologi). Gli oggetti metallici si riscaldano quando sono collegati tra punti di alimentazione e massa: possono causare ustioni gravi oppure il metallo può saldarsi ai terminali.Draft - Not Final Version
30Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 Translated Safety WarningsAdvarselFjern alle smykker (inkludert ringer, halskjeder og klokker) før du skal arbeide på utstyr som er koblet til kraftledninger. Metallgjenstander som er koblet til kraftledninger og jord blir svært varme og kan forårsake alvorlige brannskader eller smelte fast til polene.AvisoAntes de trabalhar em equipamento que esteja ligado a linhas de corrente, retire todas as jóias que estiver a usar (incluindo anéis, fios e relógios). Os objectos metálicos aquecerão em contacto com a corrente e em contacto com a ligação à terra, podendo causar queimaduras graves ou ficarem soldados aos terminais.¡Advertencia!Antes de operar sobre equipos conectados a líneas de alimentación, quitarse las joyas (incluidos anillos, collares y relojes). Los objetos de metal se calientan cuando se conectan a la alimentación y a tierra, lo que puede ocasionar quemaduras graves o que los objetos metálicos queden soldados a los bornes.Varning!Tag av alla smycken (inklusive ringar, halsband och armbandsur) innan du arbetar på utrustning som är kopplad till kraftledningar. Metallobjekt hettas upp när de kopplas ihop med ström och jord och kan förorsaka allvarliga brännskador; metallobjekt kan också sammansvetsas med kontakterna.Draft - Not Final Version
31Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 Translated Safety WarningsStatement 94—Wrist Strap WarningWarningDuring this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself.WaarschuwingDraag tijdens deze procedure aardingspolsbanden om te vermijden dat de kaart beschadigd wordt door elektrostatische ontlading. Raak het achterbord niet rechtstreeks aan met uw hand of met een metalen werktuig, omdat u anders een elektrische schok zou kunnen oplopen.VaroitusKäytä tämän toimenpiteen aikana maadoitettuja rannesuojia estääksesi kortin vaurioitumisen sähköstaattisen purkauksen vuoksi. Älä kosketa taustalevyä suoraan kädelläsi tai metallisella työkalulla sähköiskuvaaran takia.AttentionLors de cette procédure, toujours porter des bracelets antistatiques pour éviter que des décharges électriques n’endommagent la carte. Pour éviter l’électrocution, ne pas toucher le fond de panier directement avec la main ni avec un outil métallique.WarnungZur Vermeidung einer Beschädigung der Karte durch elektrostatische Entladung während dieses Verfahrens ein Erdungsband am Handgelenk tragen. Bei Berührung der Rückwand mit der Hand oder einem metallenen Werkzeug besteht Elektroschockgefahr.AvvertenzaDurante questa procedura, indossare bracciali antistatici per evitare danni alla scheda causati da un’eventuale scarica elettrostatica. Non toccare direttamente il pannello delle connessioni, né con le mani né con un qualsiasi utensile metallico, perché esiste il pericolo di folgorazione.Draft - Not Final Version
32Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 Translated Safety WarningsStatement 119—Unit Short Circuit Protection AdvarselBruk jordingsarmbånd under prosedyren for å unngå ESD-skader på kortet. Unngå direkte berøring av bakplanet med hånden eller metallverktøy, slik at di ikke får elektrisk støt.AvisoDurante este procedimento e para evitar danos ESD causados à placa, use fitas de ligação à terra para os pulsos. Para evitar o risco de choque eléctrico, não toque directamente na parte posterior com a mão ou com qualquer ferramenta metálica.¡Advertencia!Usartiras conectadas a tierra en las muñecas durante este procedimiento para evitar daños en la tarjeta causados por descargas electrostáticas. No tocar el plano posterior con las manos ni con ninguna herramienta metálica, ya que podría producir un choque eléctrico.Varning!Använd jordade armbandsremmar under denna procedur för att förhindra elektrostatisk skada på kortet. Rör inte vid baksidan med handen eller metallverktyg då detta kan orsaka elektrisk stöt.WarningThis product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that a fuse or circuit breaker no larger than 120VAC, 20A U.S. (240VAC, 16 to 20A international) is used on the phase conductors (all current-carrying conductors). The fuse or circuit breaker must have adequate safety approval recognized by the country of usage.WaarschuwingDit product is afhankelijk van de installatie van het gebouw voor bescherming tegen kortsluiting (overstroom). Zorg ervoor dat de zekering of stroomonderbreker die gebruikt wordt niet groter is dan 120 V~, 20 ampère in de V.S. of 240 V~, 16-20 ampère internationaal op de fasegeleiders (alle stroomdragende geleiders). De zekering of stroomonderbreker dient de juiste veiligheidsgoedkeuringen te hebben in het land waarin het gebruikt wordt.Draft - Not Final Version
33Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 Translated Safety WarningsVaroitusTämä tuote on riippuvainen rakennuksen oikosulkusuojauksesta (ylivirtasuojauksesta). Varmista, että vaihejohtimissa (kaikissa jännitteellisissä johtimissa) käytetään alle 240 V vaihtovirran, 16–20 ampeerin (kansainvälinen) tai 120 V vaihtovirran, 20 ampeerin (Yhdysvallat) sulaketta tai virtakytkintä. Sulakkeessa tai virtakytkimessä on oltava käyttömaassa tunnistetut, riittävät turvahyväksynnät. AttentionPour la protection contre les courts-circuits (surtension), ce produit utilise les dispositifs intégrés au bâtiment. Assurez-vous qu'un fusible ou un disjoncteur est utilisé sur les conducteurs de phase (tous les conducteurs porteurs de courant). Le fusible ou le disjoncteur (maximum 240 V CA, 16 à 20 A [aux USA, maximum 120 V CA, 20 A]) doit être conforme aux normes de sécurité en vigueur dans votre pays.WarnungDiese Produkt erfordert eine Gebäudeabsicherung gegen Kurzschluß (Überstrom). Achten Sie darauf, daß auf den Phasenleitern (allen stromführenden Leitern) eine Sicherung oder ein Schaltkreisunterbrecher verwendet wird, der nicht größer ist als 120VAC, 20A U.S. (240VAC, 16 bis 20A international). Die Sicherung oder der Schaltkreisunterbrecher muß angemessenen Sicherheitsvorschriften genügen, die den Bestimmungen des Anwendungslandes entsprechen.AvvertenzaLa protezione di questo prodotto da cortocircuiti (sovracorrente) dipende dall'impianto elettrico dell’edificio. Assicuratevi che un fusibile o interruttore di circuito con meno di 120VAC, 20A U.S. (240VAC, da 16 a 20A internazionale) venga utilizzato sui conduttori di fase (tutti i conduttori di corrente elettrica). Il fusibile o interruttore di circuito deve rispondere alle specifiche di sicurezza invigore nel paese dove viene utilizzato.AdvarselDette produktet er avhengig av bygningens installasjoner for overstrømsbeskyttelse (kortslutning). Kontroller at det ikke brukes en sikring eller overbelastningsbryter som er større enn 120 V, 20 ampere i USA, eller 240 V, 16 til 20 ampere internasjonalt, på faselederne (alle strømførende ledere). Sikringen eller overbelastningsbryteren må være sikkerhetsgodkjent i det aktuelle landet der den skal brukes.AvisoEste dispositivo depende das instalações existentes para protecção contra curto-circuitos (sobrecarga). Assegure-se de que utiliza um fusível ou um disjuntor com uma capacidade não superior a 120VAC, 20A U.S. (240VAC, 16 a 20A internacional) nos condutores de fase (todos os condutores de corrente). O fusível ou disjuntor deverá possuir as necessárias aprovações de segurança por parte das autoridades locais. ¡Advertencia!Este producto ha sido diseñado teniendo en cuenta que la instalación del edificio contará con protección contra cortocircuitos (sobrevoltajes). Asegúrese de que se usa un fusible o cortacircuitos no superior a 120VAC, 20A en los EE.UU. (240VAC, de 16 a 20A en el resto de países) en los conductores de fase (todos los conductores de transporte corriente). El fusible o cortacircuitos debe contar con las aprobaciones de seguridad adecuadas y reconocidas por el país en el que vayan a usarse. Varning!Denna produkt förlitar sig på att byggnadens installation är försedd med skydd mot kortslutning (överström). Se till att en säkring eller ett överspänningsskydd för högst 120 V~, 20 A USA (240 V~, 16 – 20 A internationellt) används på fasledarna (alla strömförande ledare). Säkringen eller överspänningsskyddet måste ha fullgoda säkerhetstillstånd som erkänns av användningslandet. Draft - Not Final Version
34Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 Translated Safety WarningsStatement 150—Power Off Before Working on SystemWarningBefore working on a system that has a standby/off switch, turn off the power by pressing the power switch to standby and unplug the power cord.WaarschuwingAlvorens aan een systeem met een standby/uit-schakelaar te werken dient u de voeding uit te schakelen door de voedingsschakelaar op standby te zetten en het voedingssnoer te verwijderen.VaroitusKatkaise virta valmiustila/virtakytkimellä varustetusta laitteesta ennen sen käyttämistä painamalla virtakytkin valmiusasentoon ja irrottamalla sähköjohto.AttentionAvant d'utiliser un système équipé d'un commutateur « Standby/Off » (pause/arrêt), coupez l'alimentation en plaçant le commutateur sur la position Standby et débranchez le cordon d'alimentation.WarnungBevor Sie an einem System mit einem Bereit-/Aus-Schalter arbeiten, stellen Sie den Strom ab, indem Sie den Stromschalter auf "Bereit" stellen und das Stromkabel herausziehen.AvvertenzaPrima di lavorare su un sistema con interruttore attesa/off, spegnetelo premendo il pulsante sulla posizione di attesa e staccate la spina elettrica. AdvarselFør det utføres arbeid på et system som har en standby/av-bryter, skal strømmen slås av ved å skyve av/på-bryteren til standby og trekke ut strømledningen.AvisoAntes de começar a trabalhar num sistema com um interruptor standby (posição de espera)/off (desligado), desligue a corrente eléctrica colocando o interruptor na posição standby e retire o cabo de alimentação da tomada.¡Advertencia!Antes de empezar a trabajar con un sistema cuyo interruptor incluya la posición standby, cierre la corriente posicionando el interruptor a standby y a continuación desconecte el cable eléctrico.Varning!Innan du arbetar på ett system med en standby-/strömbrytaromkopplare, slå av strömmen genom att ställa omkopplaren på standby och koppla ur nätsladden.Draft - Not Final Version
35Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 Translated Safety WarningsStatement 151—ISDN Network Voltages WarningWarningNetwork hazardous voltages are present in the ISDN cable. If you detach the ISDN cable, detach the end away from the router first to avoid possible electric shock. Network hazardous voltages also are present on the system card in the area of the ISDN port (RJ-45 connector), regardless of when power is turned off (by pressing power switch to standby).WaarschuwingDe ISDN-kabel bevat voltages die gevaar voor het netwerk opleveren. Als de ISDN-kabel verwijderd moet worden, verwijdert u om mogelijke elektrische schokken te vermijden eerst het uiteinde dat niet op de router is aangesloten. Verder bevat tevens de systeemkaart in de buurt van de ISDN-poort (RJ-45-aansluiting) voltages die gevaar voor het netwerk opleveren, onafhankelijk van wanneer de voeding wordt uitgeschakeld (door de voedingsschakelaar op standby te zetten).VaroitusISDN-johdossa on verkolle vaarallisia jännitteitä. Jos ISDN-kaapeli irrotetaan, irrota ensin reitittimen puoleinen pää sähköiskun välttämiseksi. Verkolle vaarallisia jännitteitä on myös järjestelmäkortissa ISDN-portin alueella (RJ-45-liitin), vaikka virta olisikin katkaistu painamalla virtakytkin valmiusasentoon.AttentionDes tensions électriques réseau dangereuses circulent sur le câble RNIS. Pour éviter tout risque de choc électrique lorsque vous débranchez ce câble, déconnectez d'abord l'extrémité non raccordée au routeur. Par ailleurs, des tensions dangereuses sont également présentes autour du port RNIS (connecteur RJ-45) de la carte système, que le système soit sous tension ou hors tension (commutateur d'alimentation sur « Standby »).WarnungAuf dem ISDN-Kabel herrschen gefährliche Spannungen. Bei Entfernung des ISDN-Kabels muß zuerst das Kabel von der Routerseite her abgetrennt werden, um einen möglichen elektrischen Schlag zu vermeiden. Gefährliche Spannungen herrschen darüber hinaus auf der Systemkarte im Bereich des ISDN-Ports (RJ-45 Steckverbinder) und zwar unabhängig davon, ob der Strom (durch Umlegung des Stromschalters auf "Bereit") abgeschaltet ist.AvvertenzaSono presenti dei voltaggi elettrici rete pericolosi nei cavi ISDN. Se staccate il cavo ISDN, dovete prima staccare l'estremità collegata al router per evitare scosse elettriche. Pericolose tensioni elettriche rete sono presente anche sulla scheda del sistema vicino alla porta ISDN (connettore RJ-45) a prescindere da quando sia stata spenta l'alimentazione elettrica (premendo il pulsante sulla posizione di attesa).AdvarselLivsfarlig spenning er til stede i nettverkets ISDN-kabel. Hvis du kobler fra ISDN-kabelen, skal enden som vender bort fra ruteren, kobles fra først for å unngå mulig elektrisk støt. Livsfarlig spenning er også til stede på nettverkets systemkort i området ved ISDN-utgangen (RJ-45-kobingen), uten hensyn til når strømmen er slått av (ved å skyve strømbryteren til standby).AvisoExistem tensões de rede perigosas no cabo de Rede Digital com Integração de Serviços-RDIS (ISDN-Integrated Services Digital Network). Se for desligar o cabo RDIS, desligue primeiro a extremidade oposta à do comutador para evitar possíveis choques eléctricos. Existem tensões de rede perigosas também na placa do sistema, nomeadamente, na área da porta RDIS (conector RJ-45), independentemente do facto da corrente estar desligada (ao colocar o interruptor em standby) ou não.Draft - Not Final Version
36Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 Translated Safety WarningsStatement 162—EU Public Network Port Warning¡Advertencia!Las líneas RSDI contienen voltajes peligrosos de la red. Si desconecta el cable RSDI, separe primero el final del router para evitar posibles choques eléctricos. La tarjeta del sistema en el área del puerto RSDI (conector RJ-45) también contiene altos voltajes de la red, independientemente de si está apagada (posicionando el interruptor de la corriente a standby). Varning!I ISDN-kabeln förekommer spänningar som är farliga för nätverk. Om du kopplar ur ISDN-kabeln, undvik eventuell elstöt genom att först koppla ur den ände som är längst bort ifrån routern. Spänningar som är farliga för nätverk förekommer också på systemkortet i området intill ISDN-porten (RJ-45-koppling), oberoende av när strömmen slås av (genom att ställa omkopplaren på standby).WarningIf the symbol of suitability with an overlaid cross appears above a port, you must not connect the port to a public network that follows the European Union standards. Connecting the port to this type of public network can cause severe injury or damage your router.WaarschuwingAls er een geschiktheidsymbool met een overgetrokken kruis boven een poort aanwezig is, dan mag u deze poort niet op een openbaar netwerk aansluiten dat aan de normen van de Europese Unie voldoet. Als u de poort op een dergelijk openbaar netwerk aansluit, kan dit ernstig letsel of schade aan uw router-eenheid veroorzaken.VaroitusJos portin päälle ilmestyy soveltuvuussymboli, jonka päällä on rasti, porttia ei saa liittää Euroopan unionin standardien mukaiseen julkiseen verkkoon. Jos portti liitetään tällaiseen julkiseen verkkoon, seurauksena voi olla henkilö- tai reititinvaurio.AttentionPour éviter tout risque d'accident corporel et/ou de dommage matériel, si le symbole de capacité barré d'une croix apparaît au-dessus d'un port, il est vivement recommandé de ne pas connecter ce port à un réseau public aux normes de l'Union Européenne.WarnungWenn oberhalb des Ports das Verträglichkeitssymbol mit einem Kreuz darüber erscheint, dürfen Sie den Port nicht an ein öffentliches Netzwerk anschließen, daß den Standards der Europäischen Gemeinschaft folgt. Das Anschließen des Port an ein solches Netzwerk kann zu schweren Verletzungen führen oder Ihren Router beschädigen. AvvertenzaSe su una porta compare il simbolo di idoneità sbarrato, significa che la porta non può essere collegata a una rete pubblica a norma UE. Collegando la porta a un simile tipo di rete pubblica si possono correre seri rischi e provocare danni al proprio router.AdvarselHvis symbolet for anvendelse med et kryss over vises over en utgang, skal utgangen ikke kobles til et offentlig nettverk som følger EU-standardene. Hvis utgangen kobles til denne typen offentlig nettverk, kan det medføre alvorlig personskade eller skade på ruteren. AvisoSe o símbolo de adequação com uma cruz sobreposta aparecer acima de uma porta, não conectar a porta a uma rede pública que obedece aos padrões da União Europeia. A conexão da porta a este tipo de rede pública pode causar avarias ou danos severos ao seu distribuidor.Draft - Not Final Version
37Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 Translated Safety WarningsStatement 199—Emergency Access Warning¡Advertencia!Si aparece el símbolo de idoneidad con una cruz sobrepuesta encima de un puerto, no debe conectar el puerto a una red pública que siga los estándares de la Unión Europea. Si conecta el puerto a este tipo de red pública puede lesionarse o dañar su router.Varning!Om lämplighetssymbolen med ett överlagt kors visas ovanför en port, får porten inte anslutas till ett offentligt nätverk av EU-standard. Om porten ansluts till denna typ av offentligt nätverk kan det förorsaka allvarlig personskada eller skada på routern. WarningThis equipment is not designed for making emergency telephony calls when the power fails. Alternative arrangements should be made for access to emergency services. Access to emergency services can be affected by any call-barring function of this equipment.WaarschuwingDeze apparatuur is niet bedoeld voor noodtelefoongesprekken bij stroomstoringen. Voor telefoondiensten in noodsituaties moet u andere maatregelen treffen. Eventuele blokkeringsfuncties van deze apparatuur kunnen van invloed zijn op de bereikbaarheid van deze telefoondiensten.VaroitusTätä laitetta ei voi käyttää hätäpuheluihin, jos sähkövirta on katkennut. Käytettävissä täytyy olla vaihtoehtoinen järjestelmä yhteyden saamiseksi hälytyskeskukseen. Hälytyskeskusyhteyden estymiseen voi vaikuttaa mikä tahansa tämän laitteiston soitonestotoiminto.AttentionCet équipement n’est pas conçu pour les télécommunications d’urgence en cas de panne d’électricité et il importe de prévoir d'autres moyens d'accès aux services d'urgence. Cependant, toute fonction d'interdiction d'appel de cet équipement risque d'avoir une incidence sur l'accès aux services d'urgence.WarnungDieses Gerät ist nicht geeignet für Notruftelefonate, wenn die Stromzufuhr ausfällt. Für das Kontaktieren von Notfalldiensten sollten alternative Maßnahmen geplant werden. Das Kontaktieren von Notfalldiensten kann von jeder der anrufsperrenden Funktionen dieses Gerätes beeinträchtigt werden.AvvertenzaQuesto apparecchio non è predisposto per effettuare chiamate d’emergenza nel caso dimancanza di alimentazione di corrente. È necessario pertanto predisporre misure alternative per consentire l’accesso ai servizi di emergenza. Tale accesso può essere inoltre influenzato dalle funzioni di blocco presenti sull’apparechio stesso.AdvarselDette utstyret har ingen funksjon for nødtjenester når strømmen er brutt. En bør utarbeide alternative ordninger hvis man må ha tilgang til nødtjenester. Tilgangen til nødtjenester kan bli påvirket av alle samtalesperrende funksjoner i dette utstyret.AvisoEste equipamento não foi concebido para estabelecer chamadas telefónicas de emergência quando faltar a energia. Devem tomar-se medidas alternativas para aceder a serviços de emergência. O acesso aos serviços de emergência pode ser afectado por qualquer função de barramento de chamadas aplicada a este equipamento.Draft - Not Final Version
38Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 Translated Safety WarningsStatement 242—Equipment Grounding Warning¡Advertencia!Este equipo no está diseñado para efectuar llamadas telefónicas de emergencia en caso de que falle la alimentación. Se deberán tomar medidas alternativas para acceder a servicios de emergencia. El acceso a servicios de emergencia puede verse afectado por cualquier función de bloqueo de llamadas que pueda tener este equipo.Varning!Denna utrustning är inte utformad för telefonsamtal i nödläge när strömmen bryts. Andra arrangemang måste göras för att kunna nå nödtjänster. Åtkomst till nödtjänster kan påverkas av alla samtalsspärrningsfunktioner i denna utrustning. WarningThis equipment needs to be grounded. Use a green and yellow 12 to 14 AWG ground wire to connect the host to earth ground during normal use.WaarschuwingDeze apparatuur hoort geaard te worden. Gebruik een groen/gele 12 - 14 AWG aarddraad om de host tijdens normaal gebruik met de aarde te verbinden.VaroitusTämä laitteisto täytyy maadoittaa. Yhdistä isäntälaite maahan normaalikäytön aikana käyttämällä vihreä-keltaista 12 - 14 AWG -maadoitusjohtoa.AttentionCet équipement doit être relié à la terre. Utilisez un fil vert et jaune de gabarit 12 à 14 (AWG) pour connecter l'hôte à la terre lors de son utilisation normale.WarnungDieses Gerät muß geerdet werden. Verwenden Sie ein grün/gelbes 12 bis 14-AWG-Erdungskabel, um damit das Host-Gerät während des normalen Betriebs zu erden.AvvertenzaQuesta apparecchiatura deve essere collegata a massa. Durante l'uso normale, collegare l'host alla massa di terra usando un filo di massa verde e giallo di diametro compreso tra 12 e 14 AWG.AdvarselDette utstyret krever jording. Bruk grønn og gul 12-14 AWG jordingsledning til å kople vertsterminalen til jording ved normal bruk.AvisoÉ necessário que este equipamento esteja ligado à terra. Utilize um fio de ligação à terra de 12 a 14 AWG, verde e amarelo, para ligar o host à ligação à terra durante a sua utilização normal.¡Advertencia!Este equipo debe conectarse a tierra. Utilizar un hilo de puesta a tierra entre 12 y 14 AWG verde y amarillo para conectar a tierra el equipo principal durante el uso normal.Varning!Denna utrustning är avsedd att jordas. Använd en gulgrön jordledning av storlek 12 till 14 AWG till att jorda värdenheten vid normal användning.Draft - Not Final Version
39Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 Translated Safety WarningsStatement 332—Antenna Installation WarningThis warning applies only to Cisco 850 series and Cisco 870 series routers.WarningIn order to comply with FCC radio frequency (RF) exposure limits, antennas should be located at a minimum of 7.9 inches (20 cm) or more from the body of all persons.WaarschuwingOm te voldoen aan de FCC radiofrequentie (RF) blootstellingslimieten dienen antennes zich minstens 20 cm of meer van de lichamen van alle personen bevinden.VaroitusFCC:n antamien radiotaajuuksille altistumista koskevien rajoitusten mukaan antennien on sijaittava vähintään 20 cm:n päässä kaikista henkilöistä.AttentionPour se conformer aux limites d'exposition à la fréquence radio préconisées par la FCC (Federal Communications Commission), les antennes doivent se situer à un minimum de 20 cm de toute personne.WarnungUm die in den FCC-Richtlinien festgelegten Expositionshöchstgrenzen für Radiofrequenzen (RF) nicht zu überschreiten, sollten Antennen mindestens 20 cm entfernt von Personen aufgestellt werden.AvvertenzaPer conformarsi ai limiti FCC di esposizione a radiofrequenza (RF), le antenne devono stare ad una distanza minima di 20 cm dal corpo di ogni persona.AdvarselI henhold til eksponeringsgrensene for radiofrekvenser (RF), skal antenner befinne seg på en avstand av minst 20 cm eller mer fra mennesker.AvisoPara estar de acordo com as normas FCC de limites de exposição para freqüência de rádio (RF), as antenas devem estar distantes no mínimo 20 cm (7,9 pol) do corpo de qualquer pessoa.¡Advertencia!Para cumplir con los límites de exposición de radio frecuencia (RF) de la Comisión Federal de Comunicaciones (FCC) es preciso ubicar las antenas a un mínimo de 20 cm (7,9 pulgadas) o más del cuerpo de las personas.Varning!För att följa FCC-exponeringsgränserna för radiofrekvens (RF), bör antenner placeras på minst 20 cm avstånd från alla människor.Draft - Not Final Version
40Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 Translated Safety WarningsStatement 353—This Product Must be ConnectedWarningThis product must be connected to a power-over-ethernet (PoE) IEEE 802.3af compliant power source or an IEC60950 compliant limited power source.WaarschuwingDit product moet worden verbonden met een stroomvoorziening die compatibel is met PoE (power-over-ethernet) IEEE 802.3af of een beperkte stroomvoorziening die compatibel is met IEC60950.VaroitusTämä tuote on liitettävä PoE (power-over-ethernet) IEEE 802.3af -yhteensopivaan virtalähteeseen tai IEC60950-yhteensopivaan rajoitettuun virtalähteeseen.AttentionCe produit doit être connecté à une source d'alimentation électrique par câble Ethernet (PoE) conforme à la norme IEEE 802.3af ou à une source d'alimentation limitée conforme à la norme IEC60950.WarnungDieses Produkt muss entweder an eine Stromquelle angeschlossen sein, die mit dem IEEE 802.3af-Standard Power-over-Ethernet (PoE) kompatibel ist oder an eine Stromquelle für geringe Leistungen, die IEC60950-kompatibel ist.AvvertenzaQuesto prodotto deve essere connesso a una fonte di alimentazione di tipo PoE (power-over-ethernet) conforme a IEEE 802.3af o a una fonte di alimentazione conforme a IEC60950.AdvarselDette produktet må være koblet til en Power-over-Ethernet (PoE) IEEE 802.3af-kompatibel strømkilde eller en IEC60950-kompatibel begrenset strømkilde.AvisoEste produto tem de estar ligado a uma fonte de alimentação compatível com a norma IEEE 802.3af, também conhecida pela sigla Power over Ethernet (PoE), ou a uma fonte de alimentação limitada compatível com a norma IEC60950.¡Advertencia!Debe conectar este producto a una fuente de alimentación en Ethernet (PoE) conforme con el estándar IEEE 802.3af, o a una fuente limitada conforme con el estándar IEC60950.Varning! Denna produkt måste vara ansluten till en PoE IEEE 802.3af-kompatibel strömkälla eller en IEC60950-kompatibel begränsad strömkälla.Draft - Not Final Version
41Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 Translated Safety WarningsStatement 371—Power Cable and AC AdapterStatement 373—Must Connect To An Indoor AntennaWarningWhen installing the product, please use the provided or designated connection cables/power cables/AC adaptors/batteries. Using any other cables/adaptors could cause a malfunction or a fire. Electrical Appliance and Material Safety Law prohibits the use of UL-certified cables (that have the “UL” or “CSA” shown on the cord), not regulated with the subject law by showing “PSE” on the cord, for any other electrical devices than products designated by CISCO.WarningThis equipment must be connected to an indoor antenna only.WaarschuwingDeze apparatuur kan alleen worden aangesloten op een antenne voor binnengebruik.VaroitusTämän laitteiston voi liittää vain sisäantenniin.AttentionCet équipement doit être connecté à une antenne intérieure uniquement.WarnungDiese Gerät darf nur an eine Innenantenne angeschlossen werden.AvvertenzaQuesto apparecchio può essere collegato solo a un'antenna da interno.AdvarselDette utstyret må kun kobles til en innendørsantenne.AvisoEste equipamento só pode ser ligado a uma antena interior.¡Advertencia!Este equipo sólo debe estar conectado a una antena de interior.Draft - Not Final Version
42Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 Translated Safety WarningsStatement 378—Read Wall-Mounting Instructions Before InstallationVarning! Den här utrustningen får endast anslutas till en inomhusantenn.WarningRead the wall-mounting instructions carefully before beginning installation. Failure to use the correct hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system.WaarschuwingLees de wandbevestigingsinstructies aandachtig door voordat u met de installatie begint. Het niet gebruiken van de juiste hardware of het opvolgen van de juiste procedures kan resulteren in een gevaarlijke situatie voor mensen en schade aan het systeem.VaroitusLue seinäkiinnitysohjeet huolellisesti läpi ennen työn aloitusta. Mikäli kiinnityksessä ei käytetä oikeanlaisia työkaluja tai ohjeita ei noudateta tarkasti, järjestelmä saattaa aiheuttaa vaaratilanteen tai se voi vaurioitua.AttentionLisez les instructions de montage murale avec attention avant de commencer l'installation. Ne pas utiliser le matériel correct ou ne pas suivre les procédures correctes pourrait donner résultat a une situation dangereuse pour les utilisateurs et endommager le système.WarnungBitte lesen Sie vor Beginn der Installierung die Anleitungen zur Wandmontage sorgfältig durch. Verwendung von inkorrekter Apparatur oder Nichtbefolgung der vorgeschriebenen Methoden kann zur Gefährdung von Personen oder Schaden am System führen.AvvertenzaLeggere attentamente le istruzioni per il montaggio al muro prima di iniziare l'installazione. Un errato uso del corretto hardware o il mancato rispetto delle corrette procedure potrebbe avere come conseguenza una situazione di pericolo per le persone e danni al sistema.AdvarselLes nøye gjennom instruksene om veggmontering før du begynner monteringen. Dersom man ikke bruker riktig maskinvare eller ikke følger riktig framgangsmåte kan det resultere i risiko for personskader og skade på systemet.Draft - Not Final Version
43Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 Translated Safety WarningsStatement 393—Explosive Device Proximity Wireless Network DeviceAvisoLeia com cuidado as instruções de montagem na parede antes de iniciar a instalação. Falha em usar o hardware correto ou em seguir os procedimentos corretos pode resultar numa situação de risco para as pessoas e danos ao sistema.¡Advertencia!Lea atentamente las instrucciones que se encuentran en la pared antes de comenzar con la instalación. Si no utiliza el hardware correcto o no sigue los procedimientos correctos se podría producir una situación peligrosa para las personas y daños al sistema.Varning! Läs väggmonteringsintruktionerna noga innan du påbörjar installationen. Försummelse av att inte använda rätt hårdvara eller att inte föjla korrekt tillvägagångsätt kan resultera i en riskabel situation för människor och kan skada systemet.WarningDo not operate your wireless network device near unshielded blasting caps or in an explosive environment unless the device has been modified to be especially qualified for such use.WaarschuwingGebruik dit draadloos netwerkapparaat alleen in de buurt van onbeschermde ontstekers of in een omgeving met explosieven indien het apparaat speciaal is aangepast om aan de eisen voor een dergelijk gebruik te voldoen.VaroitusÄlä käytä johdotonta verkkolaitetta suojaamattomien räjäytysnallien läheisyydessä tai räjäytysalueella, jos laitetta ei ole erityisesti muunnettu sopivaksi sellaiseen käyttöön. AttentionNe jamais utiliser un équipement de réseau sans fil à proximité d'un détonateur non blindé ou dans un lieu présentant des risques d'explosion, sauf si l'équipement a été modifié à cet effet.Draft - Not Final Version
44Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 Translated Safety WarningsStatement 1004—Installation InstructionsWarnungBenutzen Sie Ihr drahtloses Netzwerkgerät nicht in der Nähe ungeschützter Sprengkapseln oder anderer explosiver Stoffe, es sei denn, Ihr Gerät wurde eigens für diesen Gebrauch modifiziert und bestimmt.AvvertenzaNon utilizzare la periferica di rete senza fili in prossimità di un detonatore non protetto o di esplosivi a meno che la periferica non sia stata modificata a tale proposito.AdvarselIkke bruk den trådløse nettverksenheten nært inntil uisolerte fenghetter eller i et eksplosivt miljø med mindre enheten er modifisert slik at den tåler slik bruk.AvisoNão opere o dispositivo de rede sem fios perto de cápsulas explosivas não protegidas ou num ambiente explosivo, a não ser que o dispositivo tenha sido modificado para se qualificar especialmente para essa utilização.¡Advertencia!No utilizar un aparato de la red sin cable cerca de un detonador que no esté protegido ni tampoco en un entorno explosivo a menos que el aparato haya sido modificado con ese fin.Varning!Använd inte den trådlösa nätverksenheten i närheten av oskyddade tändhattar eller i en explosiv miljö om inte enheten modifierats för att kunna användas i sådana sammanhang.WarningRead the installation instructions before connecting the system to the power source.WaarschuwingRaadpleeg de installatie-instructies voordat u het systeem op de voedingsbron aansluit.VaroitusLue asennusohjeet ennen järjestelmän yhdistämistä virtalähteeseen.AttentionAvant de brancher le système sur la source d'alimentation, consulter les directives d'installation.WarnungVor dem Anschließen des Systems an die Stromquelle die Installationsanweisungen lesen.AvvertenzaConsultare le istruzioni di installazione prima di collegare il sistema all'alimentatore.AdvarselLes installasjonsinstruksjonene før systemet kobles til strømkilden.AvisoLeia as instruções de instalação antes de ligar o sistema à fonte de energia.¡Advertencia!Lea las instrucciones de instalación antes de conectar el sistema a la red de alimentación.Varning!Läs installationsanvisningarna innan du kopplar systemet till strömförsörjningsenheten.Draft - Not Final Version
45Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 Translated Safety WarningsStatement 1005—Circuit BreakerWarningThis product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 120 VAC, 15A U.S. (240 VAC, 10A international)WaarschuwingDit product is afhankelijk van de installatie van het gebouw voor beveiliging tegen kortsluiting (overstroom). Controleer of de beschermingsinrichting niet meer dan: 120 VAC, 15A U.S. (240 VAC, 10A international) is.VaroitusTämä tuote on riippuvainen rakennukseen asennetusta oikosulkusuojauksesta (ylivirtasuojauksesta). Varmista, että suojalaitteen mitoitus ei ole yli: 120 VAC, 15A U.S. (240 VAC, 10A international)Draft - Not Final Version
46Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 Translated Safety WarningsAttentionPour ce qui est de la protection contre les courts-circuits (surtension), ce produit dépend de l'installation électrique du local. Vérifiez que le courant nominal du dispositif de protection n'est pas supérieur à : 120 VAC, 15A U.S. (240 VAC, 10A international)WarnungDieses Produkt ist darauf angewiesen, dass im Gebäude ein Kurzschluss- bzw. Überstromschutz installiert ist. Stellen Sie sicher, dass der Nennwert der Schutzvorrichtung nicht mehr als: 120 VAC, 15A U.S. (240 VAC, 10A international) beträgt.AvvertenzaQuesto prodotto dipende dall'impianto dell'edificio per quanto riguarda la protezione contro cortocircuiti (sovracorrente). Assicurarsi che il dispositivo di protezione non abbia un rating superiore a: 120 VAC, 15A U.S. (240 VAC, 10A international)AdvarselDette produktet er avhengig av bygningens installasjoner av kortslutnings (overstrøm)-beskyttelse. Påse at verneenheten ikke er merket høyere enn: 120 VAC, 15A U.S. (240 VAC, 10A international)AvisoEste produto depende das instalações existentes para proteção contra curto-circuito (sobrecarga). Assegure-se de que o fusível ou disjuntor não seja superior a: 120 VAC, 15A U.S. (240 VAC, 10A international)¡Advertencia!Este equipo utiliza el sistema de protección contra cortocircuitos (o sobrecorrientes) del edificio. Asegúrese de que el dispositivo de protección no sea superior a: 120 VAC, 15A U.S. (240 VAC, 10A international)Varning!Denna produkt är beroende av i byggnaden installerat kortslutningsskydd (överströmsskydd). Kontrollera att skyddsanordningen inte har högre märkvärde än: 120 VAC, 15A U.S. (240 VAC, 10A international)120 VAC, 15A U.S. (240 VAC, 10A international)120 VAC, 15A U.S. (240 VAC, 10A international)120 VAC, 15A U.S. (240 VAC, 10A international)120 VAC, 15A U.S. (240 VAC, 10A international)Draft - Not Final Version
47Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 Translated Safety WarningsStatement 1008—Class 1 Laser ProductWarningClass 1 laser product.WaarschuwingKlasse-1 laser produkt.VaroitusLuokan 1 lasertuote.AttentionProduit laser de classe 1.WarnungLaserprodukt der Klasse 1.AvvertenzaProdotto laser di Classe 1.AdvarselLaserprodukt av klasse 1.AvisoProduto laser de classe 1.¡Advertencia!Producto láser Clase I.Varning!Laserprodukt av klass 1.AvisoProduto a laser de classe 1.AdvarselKlasse 1 laserprodukt.Draft - Not Final Version
48Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 Translated Safety WarningsStatement 1010—Staring into Laser BeamWarningDo not stare into the laser beam.WaarschuwingNiet in de straal staren.VaroitusÄlä katso säteeseen.AttentionNe pas fixer le faisceau des yeux.WarnungNicht direkt in den Strahl blicken.AvvertenzaNon fissare il raggio con gli occhi.AdvarselStirr ikke på strålen.AvisoNão olhe fixamente para o raio.¡Advertencia!No mirar fijamente el haz.Varning!Laserstrålning när enheten är öppen.Draft - Not Final Version
49Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 Translated Safety WarningsStatement 1015—Battery HandlingWarningThere is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.WaarschuwingEr is ontploffingsgevaar als de batterij verkeerd vervangen wordt. Vervang de batterij slechts met hetzelfde of een equivalent type dat door de fabrikant aanbevolen is. Gebruikte batterijen dienen overeenkomstig fabrieksvoorschriften weggeworpen te worden.VaroitusRäjähdyksen vaara, jos akku on vaihdettu väärään akkuun. Käytä vaihtamiseen ainoastaan saman- tai vastaavantyyppistä akkua, joka on valmistajan suosittelema. Hävitä käytetyt akut valmistajan ohjeiden mukaan.AttentionDanger d'explosion si la pile n'est pas remplacée correctement. Ne la remplacer que par une pile de type semblable ou équivalent, recommandée par le fabricant. Jeter les piles usagées conformément aux instructions du fabricant.WarnungBei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie die Batterie nur durch den gleichen oder vom Hersteller empfohlenen Batterietyp. Entsorgen Sie die benutzten Batterien nach den Anweisungen des Herstellers.AvvertenzaPericolo di esplosione se la batteria non è installata correttamente. Sostituire solo con una di tipo uguale o equivalente, consigliata dal produttore. Eliminare le batterie usate secondo le istruzioni del produttore.AdvarselDet kan være fare for eksplosjon hvis batteriet skiftes på feil måte. Skift kun med samme eller tilsvarende type som er anbefalt av produsenten. Kasser brukte batterier i henhold til produsentens instruksjoner.AvisoExiste perigo de explosão se a bateria for substituída incorrectamente. Substitua a bateria por uma bateria igual ou de um tipo equivalente recomendado pelo fabricante. Destrua as baterias usadas conforme as instruções do fabricante.¡Advertencia!Existe peligro de explosión si la batería se reemplaza de manera incorrecta. Reemplazar la batería exclusivamente con el mismo tipo o el equivalente recomendado por el fabricante. Desechar las baterías gastadas según las instrucciones del fabricante.Varning!Explosionsfara vid felaktigt batteribyte. Ersätt endast batteriet med samma batterityp som rekommenderas av tillverkaren eller motsvarande. Följ tillverkarens anvisningar vid kassering av använda batterier.Draft - Not Final Version
50Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 Translated Safety WarningsStatement 1016—Invisible Laser RadiationWarningInvisible laser radiation present.WaarschuwingOnzichtbare laserstraling aanwezig.VaroitusNäkymättömiä lasersäteitä.AttentionRayonnement laser actif mais invisible.WarnungUnsichtbare Laserstrahlung.AvvertenzaRadiazione laser invisibile.AdvarselUsynlig laserstråling.AvisoRadiação laser invisível presente.¡Advertencia!Existe radiación láser invisible.Varning!Nu pågående osynlig laserstrålning. Draft - Not Final Version
51Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 Translated Safety WarningsStatement 1021—SELV CircuitWarningTo avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telephone-network voltage (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain TNV circuits. Some LAN and WAN ports both use RJ-45 connectors. Use caution when connecting cables.WaarschuwingOm elektrische schokken te vermijden, mogen veiligheidscircuits met extra lage spanning (genaamd SELV = Safety Extra-Low Voltage) niet met telefoonnetwerkspanning (TNV) circuits verbonden worden. LAN (Lokaal netwerk) poorten bevatten SELV circuits en WAN (Regionaal netwerk) poorten bevatten TNV circuits. Sommige LAN en WAN poorten gebruiken allebei RJ-45 connectors. Ga voorzichtig te werk wanneer u kabels verbindt.VaroitusJotta vältyt sähköiskulta, älä kytke pienjännitteisiä SELV-suojapiirejä puhelinverkkojännitettä (TNV) käyttäviin virtapiireihin. LAN-portit sisältävät SELV-piirejä ja WAN-portit puhelinverkkojännitettä käyttäviä piirejä. Osa sekä LAN- että WAN-porteista käyttää RJ-45-liittimiä. Ole varovainen kytkiessäsi kaapeleita.AttentionPour éviter une électrocution, ne raccordez pas les circuits de sécurité basse tension (Safety Extra-Low Voltage ou SELV) à des circuits de tension de réseau téléphonique (Telephone Network Voltage ou TNV). Les ports du réseau local (LAN) contiennent des circuits SELV et les ports du réseau longue distance (WAN) sont munis de circuits TNV. Certains ports LAN et WAN utilisent des connecteurs RJ-45. Raccordez les câbles en prenant toutes les précautions nécessaires.WarnungZur Vermeidung von Elektroschock die Sicherheits-Kleinspannungs-Stromkreise (SELV-Kreise) nicht an Fernsprechnetzspannungs-Stromkreise (TNV-Kreise) anschließen. LAN-Ports enthalten SELV-Kreise, und WAN-Ports enthalten TNV-Kreise. Einige LAN- und WAN-Ports verwenden auch RJ-45-Steckverbinder. Vorsicht beim Anschließen von Kabeln.AvvertenzaPer evitare scosse elettriche, non collegare circuiti di sicurezza a tensione molto bassa (SELV) ai circuiti a tensione di rete telefonica (TNV). Le porte LAN contengono circuiti SELV e le porte WAN contengono circuiti TNV. Alcune porte LAN e WAN fanno uso di connettori RJ-45. Fare attenzione quando si collegano cavi.AdvarselUnngå å koble lavspenningskretser (SELV) til kretser for telenettspenning (TNV), slik at du unngår elektrisk støt. LAN-utganger inneholder SELV-kretser og WAN-utganger inneholder TNV-kretser. Det finnes både LAN-utganger og WAN-utganger som bruker RJ-45-kontakter. Vær forsiktig når du kobler kabler.Draft - Not Final Version
52Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 Translated Safety WarningsAvisoPara evitar choques eléctricos, não conecte os circuitos de segurança de baixa tensão (SELV) aos circuitos de tensão de rede telefónica (TNV). As portas LAN contêm circuitos SELV e as portas WAN contêm circuitos TNV. Algumas portas LAN e WAN usam conectores RJ-45. Tenha o devido cuidado ao conectar os cabos.¡Advertencia!Para evitar la sacudida eléctrica, no conectar circuitos de seguridad de voltaje muy bajo (safety extra-low voltage = SELV) con circuitos de voltaje de red telefónica (telephone network voltage = TNV). Los puertos de redes de área local (local area network = LAN) contienen circuitos SELV, y los puertos de redes de área extendida (wide area network = WAN) contienen circuitos TNV. En algunos casos, tanto los puertos LAN como los WAN usan conectores RJ-45. Proceda con precaución al conectar los cables.Varning!För att undvika elektriska stötar, koppla inte säkerhetskretsar med extra låg spänning (SELV-kretsar) till kretsar med telefonnätspänning (TNV-kretsar). LAN-portar innehåller SELV-kretsar och WAN-portar innehåller TNV-kretsar. Vissa LAN- och WAN-portar är försedda med RJ-45-kontakter. Iaktta försiktighet vid anslutning av kablar. Draft - Not Final Version
53Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 Translated Safety WarningsStatement 1023—No. 26 AWGWarningTo reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord.WaarschuwingOm brandgevaar te reduceren, dient slechts telecommunicatielijnsnoer nr. 26 AWG of groter gebruikt te worden.VaroitusTulipalovaaran vähentämiseksi käytä ainoastaan nro 26 AWG- tai paksumpaa tietoliikennejohdinta.AttentionPour réduire le risque d’incendie, n’utiliser que des cordons de lignes de télécommunications de type AWG nº 26 ou plus larges.WarnungZur Reduzierung der Feuergefahr eine Fernmeldeleitungsschnur der Größe 26 AWG oder größer verwenden.AvvertenzaPer ridurre il rischio di incendio, usare solo un cavo per linea di telecomunicazioni di sezione 0,12 mm2 (26 AWG) o maggiore.AdvarselBruk kun AWG nr. 26 eller telekommunikasjonsledninger med større dimensjon for å redusere faren for brann.AvisoPara reduzir o risco de incêndio, utilize apenas terminais de fio de telecomunicações Nº. 26 AWG ou superiores.AdvertenciaPara reducir el riesgo de incendios, usar sólo líneas de telecomunicaciones de calibre No. 26 AWG o más gruesas.Varning!För att minska brandrisken skall endast Nr. 26 AWG eller större telekommunikationsledning användas.Draft - Not Final Version
54Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 Translated Safety WarningsStatement 1024—Ground ConductorWarningThis equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available.WaarschuwingDeze apparatuur dient geaard te zijn. De aardingsleiding mag nooit buiten werking worden gesteld en de apparatuur mag nooit bediend worden zonder dat er een op de juiste wijze geïnstalleerde aardingsleiding aanwezig is. Neem contact op met de bevoegde instantie voor elektrische inspecties of met een elektricien als u er niet zeker van bent dat er voor passende aarding gezorgd is.VaroitusLaitteiden on oltava maadoitettuja. Älä koskaan ohita maajohdinta tai käytä laitteita ilman oikein asennettua maajohdinta. Ota yhteys sähkötarkastusviranomaiseen tai sähköasentajaan, jos olet epävarma maadoituksen sopivuudesta.AttentionCet équipement doit être mis à la masse. Ne jamais rendre inopérant le conducteur de masse ni utiliser l'équipement sans un conducteur de masse adéquatement installé. En cas de doute sur la mise à la masse appropriée disponible, s'adresser à l'organisme responsable de la sécurité électrique ou à un électricien.WarnungDieses Gerät muss geerdet sein. Auf keinen Fall den Erdungsleiter unwirksam machen oder das Gerät ohne einen sachgerecht installierten Erdungsleiter verwenden. Wenn Sie sich nicht sicher sind, ob eine sachgerechte Erdung vorhanden ist, wenden Sie sich an die zuständige Inspektionsbehörde oder einen Elektriker.AvvertenzaQuesta apparecchiatura deve essere dotata di messa a terra. Non escludere mai il conduttore di protezione né usare l'apparecchiatura in assenza di un conduttore di protezione installato in modo corretto. Se non si è certi della disponibilità di un adeguato collegamento di messa a terra, richiedere un controllo elettrico presso le autorità competenti o rivolgersi a un elettricista.AdvarselDette utstyret må jordes. Omgå aldri jordingslederen og bruk aldri utstyret uten riktig montert jordingsleder. Ta kontakt med fagfolk innen elektrisk inspeksjon eller med en elektriker hvis du er usikker på om det finnes velegnet jordning.AvisoEste equipamento deve ser aterrado. Nunca anule o fio terra nem opere o equipamento sem um aterramento adequadamente instalado. Em caso de dúvida com relação ao sistema de aterramento disponível, entre em contato com os serviços locais de inspeção elétrica ou um eletricista qualificado.¡Advertencia!Este equipo debe estar conectado a tierra. No inhabilite el conductor de tierra ni haga funcionar el equipo si no hay un conductor de tierra instalado correctamente. Póngase en contacto con la autoridad correspondiente de inspección eléctrica o con un electricista si no está seguro de que haya una conexión a tierra adecuada.Varning!Denna utrustning måste jordas. Koppla aldrig från jordledningen och använd aldrig utrustningen utan en på lämpligt sätt installerad jordledning. Om det föreligger osäkerhet huruvida lämplig jordning finns skall elektrisk besiktningsauktoritet eller elektriker kontaktas.Draft - Not Final Version
55Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 Translated Safety WarningsDraft - Not Final Version
56Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 Translated Safety WarningsStatement 1025—Use Copper Conductors OnlyWarningUse copper conductors only.WaarschuwingGebruik alleen koperen geleiders.VaroitusKäytä vain kuparijohtimia.AttentionUtilisez uniquement des conducteurs en cuivre.WarnungVerwenden Sie ausschließlich Kupferleiter.AvvertenzaUsate unicamente dei conduttori di rame.AdvarselBruk bare kobberledninger.AvisoUtilize apenas fios condutores de cobre.¡Advertencia!Emplee sólo conductores de cobre.Varning!Använd endast ledare av koppar.Draft - Not Final Version
57Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 Translated Safety WarningsStatement 1026—WAN Port Static ShockWarningHazardous network voltages are present in WAN ports regardless of whether power to the unit is OFF or ON. To avoid electric shock, use caution when working near WAN ports. When detaching cables, detach the end away from the unit first.WaarschuwingEr is gevaarlijke netwerkspanning aanwezig in WAN poorten ongeacht of de stroom naar de router INGESCHAKELD of UITGESCHAKELD is. Om elektrische schokken te vermijden, dient u voorzichtig te werk te gaan wanneer u in de nabijheid van WAN poorten werkt. Wanneer u kabels losmaakt, dient u eerst het uiteinde dat zich het verst van de eenheid vandaan bevindt, te verwijderen.VaroitusWAN-porteissa on vaarallisia verkkojännitteitä riippumatta siitä, onko yksikön virta kytketty vai ei. Välttyäksesi sähköiskulta ole varovainen työskennellessäsi WAN-porttien lähettyvillä. Kun irrotat kaapeleita, irrota yksiköstä kauimpana sijaitseva pää ensiksi.AttentionLes ports de réseau longue distance (WAN) gèrent des tensions de réseau dangereuses, que l'unité soit sous tension ou pas. Pour éviter tout risque d’électrocution, prenez toutes les précautions nécessaires avant de travailler à proximité des ports WAN. Pour déconnecter les câbles, commencez par débrancher l’extrémité la plus éloignée du routeur.WarnungIn WAN-Ports sind gefährliche Netzspannungen vorhanden, auch wenn der Strom zur Einheit abgeschaltet wurde. Zur Vermeidung von Elektroschock Vorsicht bei der Arbeit in der Nähe von WAN-Ports. Beim Abtrennen von Kabeln zuerst das vom Router entfernte Ende lösen.AvvertenzaNelle porte WAN sono presenti tensioni di rete pericolose, sia che il sistema sia acceso o meno (ON od OFF). Per evitare scosse elettriche, fare attenzione quando si lavora in prossimità di porte WAN. Quando si scollegano cavi, staccare per primo il connettore collegato al router.Advarsel!Det er livsfarlig nettverksspenning i WAN-utganger, uavhengig av om strømmen til enheten er slått av (OFF) eller på (ON). Vær forsiktig når du jobber nær WAN-utganger slik at du unngår elektrisk støt. Hvis du skal løsne kabler, må du først løsne den enden som er lengst borte fra fordelingsenheten.AvisoExistem sempre tensões de rede perigosas nas portas WAN, independentemente da corrente para a unidade estar desligada (OFF) ou ligada (ON). Para evitar choques eléctricos, tenha o devido cuidado ao trabalhar junto das portas WAN. Ao desconectar os cabos, separe primeiro a extremidade do cabo que se encontra ligada à unidade.¡Advertencia!En los puertos de redes de área extendida (WAN) existen tensiones de red peligrosas, tanto si la unidad está conectada como si está desconectada. Para evitar descargas eléctricas, proceda con precaución cuando trabaje cerca de los puertos WAN. Para desconectar los cables, desconecte primero el extremo que va a la unidad.Draft - Not Final Version
58Regulatory Compliance and Safety Information for Cisco 800 Series RoutersOL-10260-06 Translated Safety WarningsStatement 1028—More Than One Power SupplyVarning!Farlig nätverksspänning föreligger i WAN-portarna oavsett om strömförsörjningen till enheten är bruten eller ej. För att undvika elektriska stötar ska du vara försiktig vid arbete i närheten av dessa portar. När du kopplar bort en kabel ska du först koppla bort den ände som inte är ansluten till enheten.WarningThis unit might have more than one power supply connection. All connections must be removed to de-energize the unit.WaarschuwingDeze eenheid kan meer dan één stroomtoevoeraansluiting bevatten. Alle aansluitingen dienen ontkoppeld te worden om de eenheid te ontkrachten.VaroitusTässä laitteessa voi olla useampia kuin yksi virtakytkentä. Kaikki liitännät on irrotettava, jotta jännite poistetaan laitteesta.AttentionCette unité peut avoir plus d'une connexion d'alimentation. Pour supprimer toute tension et tout courant électrique de l'unité, toutes les connexions d'alimentation doivent être débranchées.WarnungDieses Gerät kann mehr als eine Stromzufuhr haben. Um sicherzustellen, dass der Einheit kein Strom zugeführt wird, müssen alle Verbindungen entfernt werden.AvvertenzaQuesta unità può avere più di una connessione all'alimentazione elettrica. Tutte le connessioni devono essere staccate per togliere la corrente dall'unità.AdvarselDenne enheten kan ha mer enn én strømtilførselskobling. Alle koblinger må fjernes fra enheten for å utkoble all strøm. Draft - Not Final Version

Navigation menu