Cisco Systems TG2050 802.11 a/b/g/n AP Module User Manual Host manual part 1
Cisco Systems Inc 802.11 a/b/g/n AP Module Host manual part 1
Contents
Host manual part 1
Americas Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Regulatory Compliance and Safety Information
for Cisco 800 Series Routers
This document provides international regulatory and safety compliance information for Cisco 800 series
routers. Use this document with the other publications for the Cisco 800 series router you have
purchased.
This document contains the following sections:
•
Product Scope, page 1
•
Electromagnetic Compatibility, page 7
•
EMC Class A, page 7
•
Telecommunications, page 10
•
Radio, page 12
•
Declarations of Conformity, page 18
•
CE Marking, page 18
•
European Union Statements, page 19
•
Environmental Compliance, page 19
•
Translated Safety Warnings, page 19
•
Obtaining Documentation and Submitting a Service Request, page 86
Product Scope
This section describes the Cisco product models addressed in this document. Table 1 indicates the
product model numbers and the following additional information:
•
Product classification
•
EMC class information
•
Wireless standard
•
Option of outdoor antenna
Draft - Not Final Version
2
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Product Scope
Ta b l e 1 Cisco Product Models Addressed in this Document
Models
Product
Classification EMC Class
Wireless
Standard
Option of
Outdoor Antenna
1.
C812G+7-K9 BNone No
2.
C819G-4G-A-K9 BNone Yes
3.
C819G-4G-G-K9 BNone Yes
4.
C819G-4G-V-K9 BNone Yes
5.
C819G+7-K9 M2M BNone No
6.
C819G-B-K9 M2M BNone No
7.
C812G-CIFI+7-E-K9 B2.4 GHz,
5 GHz No
8.
C812G-CIFI+7-N-K9 B2.4 GHz,
5 GHz No
9.
C812G-CIFI-S-A-K9 B2.4 GHz,
5 GHz No
10.
C812G-CIFI-V-A-K9 B2.4 GHz,
5 GHz No
11.
C819G-S-K9 M2M BNone No
12.
C819G-U-K9 M2M BNone No
13.
C819G-V-K9 M2M BNone No
14.
C819H-K9 BNone No
15.
C819HG-4G-A-K9 BNone Yes
16.
C819HG-4G-G-K9 BNone Yes
17.
C819HG-4G-V-K9 BNone Yes
18.
C819HG+7-K9 M2M BNone Yes
19.
C819HG-B-K9 M2M BNone Yes
20.
C819HG-S-K9 M2M BNone Yes
21.
C819HG-U-K9 M2M BNone Yes
22.
C819HG-V-K9 M2M BNone Yes
23.
C819HGW+7-A-A-K9 B2.4 GHz,
5 GHz Yes
24.
C819HGW+7-E-K9 B2.4 GHz,
5 GHz Yes
25.
C819HGW+7-N-K9 B2.4 GHz,
5 GHz Yes
26.
C819HGW-S-A-K9 B2.4 GHz,
5 GHz Yes
27.
C819HGW-V-A-K9 B2.4 GHz,
5 GHz Yes
Draft - Not Final Version
3
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Product Scope
28.
C819HWD-A-K9 B2.4 GHz,
5 GHz Yes
29.
C819HWD-E-K9 B2.4 GHz,
5 GHz Yes
30.
C866VAE-W-E-K9 Multimode
DSL B2.4 GHz,
5 GHz No
31.
C867VAE-POE-W-A-K9 Multimode
DSL B2.4 GHz,
5 GHz No
32.
C867VAE-W-A-K9 Multimode
DSL B2.4 GHz,
5 GHz No
33.
C867VAE-W-E-K9 Multimode
DSL B2.4 GHz,
5 GHz No
34.
C881-V-K9 Voice BNone No
35.
C881G+7-A-K9 Ethernet BNone No
36.
C881G+7-K9 Ethernet BNone No
37.
C881G-B-K9 Ethernet BNone No
38.
C881G-S-K9 Ethernet BNone No
39.
C881G-U-K9 Ethernet BNone No
40.
C881G-V-K9 Ethernet BNone No
41.
C881SRST-K9 Ethernet BNone No
42.
C881SRSTW-GN-A-K9 Ethernet B2.4 GHz No
43.
C881SRSTW-GN-E-K9 Ethernet B2.4 GHz No
44.
C881W-A-K9 Ethernet B2.4 GHz No
45.
C881W-E-K9 Ethernet B2.4 GHz No
46.
C881W-P-K9 Ethernet B2.4 GHz No
47.
C881WD-A-K9 Ethernet B2.4 GHz,
5 GHz No
48.
C881WD-E-K9 Ethernet B2.4 GHz,
5 GHz No
49.
C886VA-W-E-K9 Multimode
DSL A2.4 GHz No
50.
C886VAG+7-K9 Multimode
DSL ANone No
51.
C887VA-V-K9 Vo ic e ANone No
52.
C887VA-V-K9 Multimode
DSL ANone No
53.
C887VA-V-W-E-K9 Multimode
DSL A2.4 GHz No
Table 1 Cisco Product Models Addressed in this Document
Models
Product
Classification EMC Class
Wireless
Standard
Option of
Outdoor Antenna
Draft - Not Final Version
4
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Product Scope
54.
C887VA-W-A-K9 Multimode
DSL A2.4 GHz No
55.
C887VA-W-E-K9 Multimode
DSL A2.4 GHz No
56.
C887VA-WD-A-K9 Multimode
DSL A2.4 GHz,
5 GHz No
57.
C887VA-WD-E-K9 Multimode
DSL A2.4 GHz,
5 GHz No
58.
C887VAG+7-K9 Multimode
DSL ANone No
59.
C887VAG-S-K9 Multimode
DSL ANone No
60.
C887VAGW+7-A-K9 Multimode
DSL A2.4 GHz,
5 GHz No
61.
C887VAGW+7-E-K9 Multimode
DSL A2.4 GHz,
5 GHz No
62.
C887VAMG+7-K9 Multimode
DSL ANone No
63.
C888EA-K9 SHDSL ANone No
64.
C888EG+7-K9 SHDSL ANone No
65.
C888ESRST-K9 SHDSL ANone No
66.
C888ESRSTW-GNA-K9 SHDSL A2.4 GHz No
67.
C888ESRSTW-GNE-K9 SHDSL A2.4 GHz No
68.
C888SRST-K9 SHDSL ANone No
69.
C888SRSTW-GN-A-K9 SHDSL A2.4 GHz No
70.
C888SRSTW-GN-E-K9 SHDSL A2.4 GHz No
71.
C892FSP-K9 BNone No
72.
C896VA BNone No
73.
C897VA Multimode
DSL BNone No
74.
C897VA-M Multimode
DSL BNone No
75.
C897VAM-W Multimode
DSL B2.4 GHz,
5 GHz No
76.
C897VAW Multimode
DSL B2.4 GHz,
5 GHz No
77.
C898EA SHDSL ANone No
78.
CISCO861-K9 Ethernet BNone No
79.
CISCO861-PCI-K9 Ethernet BNone No
Table 1 Cisco Product Models Addressed in this Document
Models
Product
Classification EMC Class
Wireless
Standard
Option of
Outdoor Antenna
Draft - Not Final Version
5
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Product Scope
80.
CISCO861W-GN-A-K9 Ethernet B2.4 GHz No
81.
CISCO861W-GN-E-K9 Ethernet B2.4 GHz No
82.
CISCO861W-GN-P-K9 Ethernet B2.4 GHz No
83.
CISCO866VAE Multimode
DSL BNone No
84.
CISCO866VAE-K9 Multimode
DSL BNone No
85.
CISCO867VAE Multimode
DSL BNone No
86.
CISCO867VAE-K9 Multimode
DSL BNone No
87.
CISCO881-K9 Ethernet BNone No
88.
CISCO881-PCI-K9 Ethernet BNone No
89.
CISCO881-SEC-K9 Ethernet BNone No
90.
CISCO881C-K9 Ethernet BNone No
91.
CISCO881C-W-E-K9 Ethernet B2.4 GHz No
92.
CISCO881G-K9 Ethernet BNone No
93.
CISCO881GC-K9 Ethernet BNone No
94.
CISCO881GC-W-E-K9 Ethernet B2.4 GHz No
95.
CISCO881GW-GN-A-K9 Ethernet B2.4 GHz,
5 GHz No
96.
CISCO881GW-GN-E-K9 Ethernet B2.4 GHz,
5 GHz No
97.
CISCO881W-GN-A-K9 Ethernet B2.4 GHz No
98.
CISCO881W-GN-E-K9 Ethernet B2.4 GHz No
99.
CISCO881W-GN-P-K9 Ethernet B2.4 GHz,
5 GHz No
100.
CISCO886VA-J-K9 Multimode
DSL ANone No
101.
CISCO886VA-K9 Multimode
DSL ANone No
102.
CISCO886VA-SEC-K9 Multimode
DSL ANone No
103.
CISCO887V-K9 Multimode
DSL ANone No
104.
CISCO887V-SEC-K9 Multimode
DSL ANone No
105.
CISCO887VA-K9 Multimode
DSL ANone No
Table 1 Cisco Product Models Addressed in this Document
Models
Product
Classification EMC Class
Wireless
Standard
Option of
Outdoor Antenna
Draft - Not Final Version
6
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Product Scope
106.
CISCO887VA-M-K9 Multimode
DSL ANone No
107.
CISCO887VA-SEC-K9 Multimode
DSL ANone No
108.
CISCO887VG-K9 Multimode
DSL ANone No
109.
CISCO887VGW-GNA-K9 VDSL A2.4 GHz No
110.
CISCO887VGW-GNE-K9 VDSL A2.4 GHz No
111.
CISCO887VW-GNA-K9 Multimode
DSL A2.4 GHz No
112.
CISCO887VW-GNE-K9 Multimode
DSL A2.4 GHz No
113.
CISCO888-K9 SHDSL ANone No
114.
CISCO888-SEC-K9 SHDSL ANone No
115.
CISCO888E-K9 SHDSL ANone No
116.
CISCO888EW-GNA-K9 SHDSL A2.4 GHz No
117.
CISCO888EW-GNE-K9 SHDSL A2.4 GHz No
118.
CISCO888G-K9 SHDSL ANone No
119.
CISCO888GW-GN-A-K9 SHDSL A2.4 GHz No
120.
CISCO888GW-GN-E-K9 SHDSL A2.4 GHz No
121.
CISCO888W-GN-A-K9 SHDSL A2.4 GHz No
122.
CISCO888W-GN-E-K9 SHDSL A2.4 GHz No
123.
CISCO891-K9 Ethernet BNone No
124.
CISCO891-PCI-K9 Ethernet BNone No
125.
CISCO891C-K9 Ethernet BNone No
126.
CISCO891C-W-C-K9 Ethernet B2.4 GHz,
5 GHz No
127.
CISCO891W-AGN-A-K9 Ethernet B2.4 GHz,
5 GHz No
128.
CISCO891W-AGN-C-K9 Ethernet B2.4 GHz,
5 GHz No
129.
CISCO891W-AGN-N-K9 Ethernet B2.4 GHz,
5 GHz No
130.
CISCO892-K9 Ethernet BNone No
131.
CISCO892C-K9 Ethernet BNone No
132.
CISCO892C-W-C-K9 Ethernet B2.4 GHz,
5 GHz No
133.
CISCO892F-K9 Ethernet BNone No
Table 1 Cisco Product Models Addressed in this Document
Models
Product
Classification EMC Class
Wireless
Standard
Option of
Outdoor Antenna
Draft - Not Final Version
7
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Electromagnetic Compatibility
Electromagnetic Compatibility
This section describes electromagnetic compatibility (EMC) compliance conditions. It contains the
following:
•
EMC Class A
•
EMC Class B
EMC Class A
This section includes the following EMC Class A warnings:
•
Statement 2017—Class A Notice for FCC
•
CISPR 22 Class A Statement
•
Statement 2021—Class A Notice for Canada
•
Statement 191—VCCI Class A Warning for Japan
Statement 2017—Class A Notice for FCC
Modifying the equipment without Cisco's authorization may result in the equipment no longer
complying with FCC requirements for Class A or Class B digital devices. In that event, your right to use
the equipment may be limited by FCC regulations, and you may be required to correct any interference
to radio or television communications at your own expense.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
134.
CISCO892FW-A-K9 Ethernet B2.4 GHz,
5 GHz No
135.
CISCO892FW-E-K9 Ethernet B2.4 GHz,
5 GHz No
136.
CISCO892J-K9 Ethernet ANone No
137.
CISCO892W-AGN-E-K9 Ethernet B2.4 GHz,
5 GHz No
138.
CISCO892W-AGN-P-K9 Ethernet B2.4 GHz,
5 GHz No
Table 1 Cisco Product Models Addressed in this Document
Models
Product
Classification EMC Class
Wireless
Standard
Option of
Outdoor Antenna
Draft - Not Final Version
8
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Electromagnetic Compatibility
CISPR 22 Class A Statement
This equipment complies with the requirements of CISPR 22 (EN 55022) for Class A Information
Technology Equipment (ITE).
Warning
This is a class A product. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.
Statement 2021—Class A Notice for Canada
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
Statement 191—VCCI Class A Warning for Japan
EMC Class B
Statement 2018—Class B Notice for FCC
Modifying the equipment without Cisco’s authorization may result in the equipment no longer
complying with FCC requirements for Class B digital devices. In that event, your right to use the
equipment may be limited by FCC regulations, and you may be required to correct any interference to
radio or television communications at your own expense.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
Warning
This is a Class A product based on the standard of the VCCI Council. If this equipment is used in a
domestic environment, radio interference may occur, in which case, the user may be required to take
corrective actions.
VCCI-A
Draft - Not Final Version
9
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Electromagnetic Compatibility
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
•
Consult the dealer or an experienced radio/TV technician for help.
CISPR 22 Class B Statement
Emissions:
This equipment complies with the requirements of CISPR 22 (EN 55022) for Class B Information
Technology Equipment (ITE).
Canada Compliance Statements
Statement 2022—Class B Notice for Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Industry Canada Notice
This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications.
This is confirmed by the registration number. The abbreviation, IC, before the registration number
signifies that registration was performed based on a Declaration of Conformity indicating that Industry
Canada technical specifications were met. It does not imply that Industry Canada approved the
equipment.
The Ringer Equivalence Number (REN) for this terminal equipment is 01. The REN assigned to each
terminal equipment provides an indication of the maximum number of terminals allowed to be connected
to a telephone interface. The termination on an interface may consist of any combination of devices
subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does
not exceed five.
Le présent matériel est conforme aux spécifications techniques applicables d'Industrie Canada. Cette
conformité est confirmée par le numéro d'enregistrement. Le sigle IC, placé devant le numéro
d'enregistrement, signifie que l’enregistrement s’est effectué conformément à une déclaration de
conformité et indique que les spécifications techniques d'Industrie Canada ont été respectées. Il
n’implique pas qu’Industrie Canada a approuvé le matériel.
L'indice d'équivalence de la sonnerie (IES) du présent matériel est de 01. L'IESassigné à chaque
dispositif terminal indique le nombre maximal de terminaux qui peuvent êtreraccordés à une interface
téléphonique. La terminaison d'une interface peut consister en unecombinaison quelconque de
dispositifs, à la seule condition que la somme d'indicesd'équivalence de la sonnerie de tous les dispositifs
n'excède pas 5.
Draft - Not Final Version
10
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Telecommunications
Australia Compliance Statement
Network connected equipment is approved to the Australian and New Zealand Safety and EMC
requirements by Cisco Systems Incorporated which is a Recognized Laboratory by ACA and New
Zealand. Stand-alone power supply modules provided with this equipment are separately approved by
an Australian State designated Electricity Authority.
Statement 157—VCCI Compliance for Class B Equipment
Telecommunications
This section describes telecommunications compliance. It contains the following:
•
Statement 3023—Equipment That Complies With 47 CFR Part 68
Statement 3023—Equipment That Complies With 47 CFR Part 68
This equipment complies with Part 68 of the FCC rules and the requirements adopted by ACTA. On the
bottom of the equipment is a label that contains, among other information, a product identifier in the
format, US:AAAAANNAAAAAAA. If requested, this number must be provided to the telephone
company.
Applicable connector jack Universal Service Order Codes (“USOC”) for the Equipment is RJ11.
A plug and jack used to connect this equipment to the premises wiring and telephone network must
comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant
telephone cord and modular plug is provided with this product. It is designed to be connected to a
compatible modular jack that is also compliant. See installation instructions for details.
The REN is used to determine the number of devices that may be connected to a telephone line.
Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming
call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number
of devices that may be connected to a line, as determined by the total RENs, contact the local telephone
Warning
This is a Class B product based on the standard of the VCCI Council. If this is used near a radio or
television receiver in a domestic environment, it may cause radio interference. Install and use the
equipment according to the instruction manual.
VCCI-B
Draft - Not Final Version
11
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Telecommunications
company. For products approved after July 23, 2001, the REN for this product is part of the product
identifier that has the format US:AAAAANNAAAAAAA. The digits represented by 01 are the REN
without a decimal point.
If this Router (Cisco 860VAE) causes harm to the telephone network, the telephone company will notify
you in advance that temporary discontinuance of service may be required. If advance notice is not
practical, the telephone company will notify the customer as soon as possible. Also, you will be advised
of your right to file a complaint with the FCC if you believe it is necessary.
The telephone company may make changes in its facilities, equipment, operation, or procedures that
could affect the operation of this equipment. If this happens, the telephone company will provide
advance notice in order for you to make the necessary modifications to maintain uninterrupted service.
If trouble is experienced with this Router (Cisco 860VAE), for repair or warranty information, please
contact Cisco Systems, Inc. – address: 170 West Tasman Dr. San Jose, CA95134 USA, phone number:
1 408 526 4000. If the equipment is causing harm to the telephone network, the telephone company may
request that you disconnect the equipment until the problem is resolved.
Connection to party line service is subject to state tariffs. Contact the state public utility commission,
public service commission or corporation commission for information.
If your home has specially wired alarm equipment connected to the telephone line, ensure the installation
of this equipment does not disable your alarm equipment. If you have questions about what will disable
alarm equipment, consult your telephone company or a qualified installer.
WHEN PROGRAMMING EMERGENCY NUMBERS AND/OR MAKING TEST CALLS TO
EMERGENCY NUMBERS:
1.
Remain on the line and briefly explain to the dispatcher the reason for the call.
2.
Perform such activities in the off-peak hours, such as early morning or late evenings.
The facility interface and service order codes for the Cisco 800 series routers are shown in Table 2.
Cisco 800 series and SOHO series routers bearing labeling identification number US:5B1MFNA0013 or
US:5B1DLO1B0144, and Cisco 860 and 880 router models bearing labeling identification number
US:5B1ISO1B0247 comply with the following requirement:
•
FCC Rules and Regulations 47 CFR Part 68
•
TIA-968-A, Technical Criteria for Terminal Equipment to Prevent Harm to the Telephone Network,
July 2002, as adopted by the Administrative Council on Terminal Attachments (ACTA).
Ta b l e 2 Cisco 800 Series Routers Facility Interface and Service Order Codes
Port Type
Facility Interface
Code
Service Order
Code Jack Type
ISDN BRI S/T 02IS5 6.0N RJ-49C
ISDN BRI U 02IS5 6.0N RJ-49C
DSU 56K 04DU5-56 6.0N RJ-48S
ADSL Metallic —RJ-11C
SHDSL Metallic —RJ-14C
FXO 02LS2 None RJ-11C
FXO 02GS2 None RJ-21X
DID 02RV2.T AS.2 RJ-11C
Analog Modem 02LS2 None RJ-11C
Draft - Not Final Version
12
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Radio
Cisco 801, 802, 803, 804, 805, 806, 811, 813, 815, 826, 827, 828, 831, 836, 837, 851, 856, 857, 858,
871, 877, 878, 881-V, and 887VA-V routers, and Cisco SOHO 76, 77, 78, 91, 96, and 97 routers bearing
labeling identification number US:5BMFMAM0013 or US:5B1DLO1B0144, and IAD881F, IAD881B,
C881SRST, 888, 888G, IAD888F, IAD888B, C888SRST, routers bearing labeling identification number
US:5B1IS01B0247, and Cisco 891, 892 routers bearing labeling identification number
US:5B1IS01B0268 comply with the following requirement:
•
FCC Rules and Regulations 47 CFR Part 68
•
TIA-968-A, Technical Criteria for Terminal Equipment to Prevent Harm to the Telephone Network,
2002, as adopted by the Administrative Council on Terminal Attachments (ACTA).
Cisco’s Supplier Declarations of Conformity are available online at:
http://wwwin-tools.cisco.com/cse/prdapp/jsp/ExternalSearch.jsp?selNavObjId=search|extSearch
Radio
This section describes radio compliance conditions. It contains the following:
•
Power Level Settings
•
Canadian Compliance Statement
•
Statement 287—Declaration of Conformity to R&TTE Directive 1999/5/EC for the European
Community, Switzerland, Norway, Iceland and Liechtenstein
•
RF Exposure
•
Statement 372—Wireless LAN Products
•
Statement 391—Low-Power Radio Data Communications Systems (ARIB-STD)
•
Administrative Rules for Cisco Wireless Devices in Taiwan
Radio: Cautions
Caution
The Part 15 radio device operates on a non-interference basis with other devices operating at this
frequency when using the integrated antennas. Any changes or modification to the product not expressly
approved by Cisco could void the user’s authority to operate this device.
Draft - Not Final Version
13
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Radio
Radio: Statements and Additional Information
Note
This equipment is intended to be used in all EU and EFTA countries. Outdoor use may be restricted to
certain frequencies and/or may require a license for operation. For more details, contact Cisco Corporate
Compliance.
Cautions Relevant to 5 GHz Radio
Statement 372—Wireless LAN Products
All wireless LAN products in the 5.2/5.3GHz band cannot be used outdoors. Use the product only
indoors.
Indoor Operation
Caution
This device operates in the 5150 to 5250 MHz and 5470 to 5725 MHz bands and is therefore restricted
to indoor operation only per FCC guidance. The use of this system outside is in non compliance of the
FCC regulations and guidelines. Please contact your Cisco sales person for further detail.
Power Level Settings
Table 3 lists the maximum power level settings permissible for the radio modules.
Canadian Compliance Statement
This Class B Digital apparatus meets all the requirements of the Canadian Interference-Causing
Equipment Regulations.
Ta b l e 3 Maximum Rated Power Output for the Radios
Radio FCC ID
Maximum Power Setting (dBM)
802.11a 802.11b (2.4 GHz) 802.11g (2.4 GHz) 802.11n (2.4, 5 GHz)
LDKXSNIACG13 —19 17 —
MCL74487504 —17 15 16
MCL74487604 16 17 15 15
LDKTG2050 15 17 15 16
MCL74751901 —17 15 16 (2.4 GHz only)
Draft - Not Final Version
14
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Radio
Cet appareil numerique de la classe B respecte les exigences du Reglement sur le material broilleur du
Canada.
This device complies with Class B Limits of Industry Canada. Operation is subject to the following two
conditions:
•
This device may not cause harmful interference.
•
This device must accept any interference received, including interference that may cause undesired
operation.
Cisco 2.4-GHz and 5-GHz Access Points are certified to the requirements of RSS-210 for 2.4-GHz
spread spectrum devices. The use of this device in a system operating either partially or completely
outdoors may require the user to obtain a license for the system according to the Canadian regulations.
For further information, contact your local Industry Canada office.
Statement 287—Declaration of Conformity to R&TTE Directive 1999/5/EC for the
European Community, Switzerland, Norway, Iceland and Liechtenstein
This section contains compliance information relevant to the European Union and other countries that
have implemented the EU Directive 1999/5/EC.
The information contained in this section applies to the following wireless LAN products:
English:
This equipment is in compliance with the essential requirements and other relevant provisions of
Directive 1999/5/EC.
[Bulgarian]:
[Czech]:
Dansk
[Danish]:
Dette udstyr er i overensstemmelse med de væsentlige krav og andre relevante bestemmelser i
Direktiv 1999/5/EF.
Deutsch
[German]:
Dieses Gerät entspricht den grundlegenden Anforderungen und den weiteren entsprechenden
Vorgaben der Richtlinie 1999/5/EU.
Eesti
[Estonian]:
See seade vastab direktiivi 1999/5/EÜ olulistele nõuetele ja teistele asjakohastele sätetele.
Español
[Spanish]:
Este equipo cumple con los requisitos esenciales asi como con otras disposiciones de la Directiva
1999/5/CE.
[Greek]:
Français
[French]:
Cet appareil est conforme aux exigences essentielles et aux autres dispositions pertinentes de la
Directive 1999/5/EC.
Íslenska
[Icelandic]:
Þetta tæki er samkvæmt grunnkröfum og öðrum viðeigandi ákvæðum Tilskipunar 1999/5/EC.
Draft - Not Final Version
15
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Radio
RF Exposure
The radio has been found to be compliant to the requirements set forth in CFR 47 Sections 2.1091, and
15.247 (b) (4) addressing RF Exposure from radio frequency devices as defined in Evaluating
Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields. The
equipment should be installed more than 20 cm (7.9 in.) from your body or nearby persons. The access
Italiano
[Italian]:
Questo apparato é conforme ai requisiti essenziali ed agli altri principi sanciti dalla Direttiva
1999/5/CE.
Latviski
[Latvian]:
[Lithuanian]:
Nederlands
[Dutch]:
Dit apparaat voldoet aan de essentiele eisen en andere van toepassing zijnde bepalingen van de
Richtlijn 1999/5/EC.
Malti
[Maltese]:
Magyar
[Hungarian]:
Norsk
[Norwegian]:
Dette utstyret er i samsvar med de grunnleggende krav og andre relevante bestemmelser i
EU-direktiv 1999/5/EF.
Polski
[Polish]:
Português
[Portuguese]:
Este equipamento está em conformidade com os requisitos essenciais e outras provisões relevantes
da Directiva 1999/5/EC.
[Romanian]:
Acest echipament este in conformitate cu cerintele esentiale si cu alte prevederi relevante ale
Directivei 1999/5/EC.
Slovensko
[Slovenian]:
Ta naprava je skladna z bistvenimi zahtevami in ostalimi relevantnimi pogoji Direktive 1999/5/EC.
Slovensky
[Slovak]:
Toto zariadenie je v zhode so základnými požiadavkami a inými príslušnými nariadeniami direktív:
1999/5/EC.
Suomi
[Finnish]:
Svenska
[Swedish]:
Draft - Not Final Version
16
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Radio
point must be installed to maintain a minimum 20 cm (7.9 in.) co-located separation distance from other
FCC approved indoor/outdoor antennas used with the access point. Any antennas or transmitters not
approved by the FCC cannot be co-located with the access point. The access point’s co-located 2.4 GHz
integrated antennas support a minimum separation distance of 8 cm (3.2 in.) and are compliant with the
applicable FCC RF exposure limit when transmitting simultaneously.
Note
Dual antennas used for diversity operation are not considered co-located.
Statement 391—Low-Power Radio Data Communications Systems (ARIB-STD)
This equipment shares a frequency band with a wide range of equipment: e.g. industrial, scientific, and
medical equipment such as microwave ovens, premises radio station (radio stations requiring licenses),
and specified low-power radio stations (radio stations not requiring licenses) for RFID used for factory
production lines as well as amateur radio stations (radio stations requiring licenses).
1.
Before use, confirm that no premises radio stations and specified low-power radio stations for RFID
or amateur radio stations operate in your vicinity.
2.
In the event that this equipment causes harmful interference to any premises radio station for RFID,
immediately change frequencies or halt radio wave emission and contact us at the information
indicated below for consultation on interference avoidance measures (e.g. partition installation).
3.
Contact us at the information indicated below URL if this equipment causes harmful interference to
any specified low-power radio stations for RFID or amateur radio stations or if other problems arise.
Contact us at: http://www.cisco.com/jp/
Administrative Rules for Cisco Wireless Devices in Taiwan
This section provides administrative rules for operating Cisco wireless access products in Taiwan. The
rules are provided in both Chinese and English.
Wireless Devices with IEEE 802.11a/b/g Radios
This equipment is limited for indoor use.
Draft - Not Final Version
17
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Radio
Statement 392—Device is Prohibited for Outdoor Operations Within the 5.25–5.35 GHz Band
To avoid radio interference, this device is prohibited for outdoor operations within the 5.25–5.35 GHz
band. (for unit covers 5.25–5.35 GHz, on both unit and manual)
Administrative Rules for Low-power Radio-frequency Devices (for all wireless unit, on manual)
Article 12 For those low-power radio-frequency devices that have already received a type-approval,
companies, business units or users should not change its frequencies, increase its power or change its
original features and functions.
Article 14 The operation of the Low-power Radio-frequency Devices is subject to the conditions that no
harmful interference is caused to aviation safety and authorised radio station; and if interference is
caused, the user must stop operating the device immediately and can’t re-operate it until the harmful
interference is clear.
The authorised radio station means a radio-communication service operating in accordance with
COMMUNICATION ACT.
The operation of the Low-power Radio-frequency Devices is subject to the interference caused by the
operation of an authorised radio station, by another intentional or unintentional radiator, by industrial,
scientific and medical (ISM) equipment, or by an incidental radiator.
Low-power Radio-frequency Devices Technical Specifications (for unit covers 5.25–5.35 GHz, on
manual)
4.7 Unlicensed National Information Infrastructure
4.7.5 Within the 5.25–5.35 GHz band, U-NII devices will be restricted to indoor operations to reduce
any potential for harmful interference to co-channel MSS operations.
4.7.6 The U-NII devices shall accept any interference from legal communications and shall not interfere
the legal communications. If interference is caused, the user must stop operating the device immediately
and can’t re-operate it until the harmful interference is clear.
4.7.7 Manufacturers of U-NII devices are responsible for ensuring frequency stability such that an
emissionis maintained within the band of operation under all conditions of normal operation as specified
in the user manual.
Draft - Not Final Version
18
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Declarations of Conformity
Declarations of Conformity
The Declaration of Conformity statements for this product can be found at the following URL:
http://www.ciscofax.com
Note
If you still have questions regarding the compliance of these products or you cannot find the information
you are looking for, please send an e-mail request to complianceinfo@cisco.com.
CE Marking
This product bears the CE mark in conformance with Annex VII of Directive 1999/5/CE.
The following CE mark and class-2 identifier is affixed to the equipment and packaging:
Draft - Not Final Version
19
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
European Union Statements
European Union Statements
The following statements apply in the European Union (EU).
•
Network Termination Point Statement
•
ISDN S/T Ports Statement
Network Termination Point Statement
This product does not contain a “Network Termination Point” (NTP) as defined by ETSI 300 386-2. This
product is classified by the manufacturer as “Terminal Equipment.” If you have any additional questions,
please contact your local network operator.
ISDN S/T Ports Statement
These ports have not been classified as “directly connected ports” to outside cables as defined by
CISPR 24, 1997 by the manufacturer. If you have any additional questions, please contact your local
network operator.
Environmental Compliance
The following statement(s) address environmental compliance.
•
Statement 6005—California Perchlorate Contamination Prevention Act (Title 22, California Code
of Regulations, Chapter 33)
Statement 6005—California Perchlorate Contamination Prevention Act
(Title 22, California Code of Regulations, Chapter 33)
The battery inside this product might contain perchlorate, a known hazardous substance, so special
handling and disposal of this product might be necessary. For more information about perchlorate
and best management practices for perchlorate-containing substances, see
http://www.dtsc.ca.gov/HazardousWaste/Perchlorate/index.cfm.
Translated Safety Warnings
This section contains the translations of the following warning statements. A warning means danger. You
are in a situation that could cause bodily injury. Before working on equipment, be aware of the hazards
involved with electrical circuitry and standard safety practices to prevent accidents.
•
Statement 1071—Warning Definition
•
Statement 19—TN Power Warning
•
Statement 23—ISDN Connection Warning
•
Statement 43—Jewelry Removal Warning
Draft - Not Final Version
20
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Translated Safety Warnings
•
Statement 94—Wrist Strap Warning
•
Statement 119—Unit Short Circuit Protection
•
Statement 150—Power Off Before Working on System
•
Statement 151—ISDN Network Voltages Warning
•
Statement 162—EU Public Network Port Warning
•
Statement 199—Emergency Access Warning
•
Statement 242—Equipment Grounding Warning
•
Statement 332—Antenna Installation Warning
•
Statement 353—This Product Must be Connected
•
Statement 371—Power Cable and AC Adapter
•
Statement 373—Must Connect To An Indoor Antenna
•
Statement 378—Read Wall-Mounting Instructions Before Installation
•
Statement 393—Explosive Device Proximity Wireless Network Device
•
Statement 1004—Installation Instructions
•
Statement 1005—Circuit Breaker
•
Statement 1008—Class 1 Laser Product
•
Statement 1010—Staring into Laser Beam
•
Statement 1015—Battery Handling
•
Statement 1016—Invisible Laser Radiation
•
Statement 1021—SELV Circuit
•
Statement 1023—No. 26 AWG
•
Statement 1024—Ground Conductor
•
Statement 1025—Use Copper Conductors Only
•
Statement 1026—WAN Port Static Shock
•
Statement 1028—More Than One Power Supply
•
Statement 1030—Equipment Installation
•
Statement 1031—EU Public Network Port
•
Statement 1033—SELV-IEC 60950 DC Power Supply
•
Statement 1035—Proximity to Water
•
Statement 1036—Telephone Jacks in Wet Locations
•
Statement 1037—Uninsulated Wires or Terminals
•
Statement 1038—Telephone Use During an Electrical Storm
•
Statement 1040—Product Disposal
•
Statement 1042—Ring Signal Generator
•
Statement 1046—Installing or Replacing the Unit
•
Statement 1052—Installing and Grounding the Antenna
•
Statement 1056—Unterminated Fiber Cable
•
Statement 1057—Hazardous Radiation Exposure
Draft - Not Final Version
21
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Translated Safety Warnings
•
Statement 1072—Shock Hazard from Interconnections
•
Statement 1073—No User-Serviceable Parts
•
Statement 1074—Comply with Local and National Electrical Codes
•
Statement 1077—Do Not Operate Unit Without Covers
•
Statement 1088—Avoid Servicing Outdoor Connections During an Electrical Storm
Statement 1071—Warning Definition
Warning
IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar
with standard practices for preventing accidents. Use the statement number provided at the end of
each warning to locate its translation in the translated safety warnings that accompanied this
device.
SAVE THESE INSTRUCTIONS
Waarschuwing
BELANGRIJKE VEILIGHEIDSINSTRUCTIES
Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan
veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij
elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard
praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de
waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt
raadplegen.
BEWAAR DEZE INSTRUCTIES
Varoitus
TÄRKEITÄ TURVALLISUUSOHJEITA
Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin
käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu
onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen
mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien
lausuntonumeroiden avulla.
SÄILYTÄ NÄMÄ OHJEET
Attention
IMPORTANTES INFORMATIONS DE SÉCURITÉ
Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant
entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez
conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures
couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des
avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil,
référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.
CONSERVEZ CES INFORMATIONS
Draft - Not Final Version
22
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Translated Safety Warnings
Warnung
WICHTIGE SICHERHEITSHINWEISE
Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen
kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und
den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder
Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten
Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.
BEWAHREN SIE DIESE HINWEISE GUT AUF.
Avvertenza
IMPORTANTI ISTRUZIONI SULLA SICUREZZA
Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle
persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli
relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti.
Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le
traduzioni delle avvertenze riportate in questo documento.
CONSERVARE QUESTE ISTRUZIONI
Advarsel
VIKTIGE SIKKERHETSINSTRUKSJONER
Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du
begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med
elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten
av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne
enheten.
TA VARE PÅ DISSE INSTRUKSJONENE
Aviso
INSTRUÇÕES IMPORTANTES DE SEGURANÇA
Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de
lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos
perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de
prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para
localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo.
GUARDE ESTAS INSTRUÇÕES
¡Advertencia!
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular
cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los
procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el
número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña
a este dispositivo.
GUARDE ESTAS INSTRUCCIONES
Draft - Not Final Version
23
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Translated Safety Warnings
Varning!
VIKTIGA SÄKERHETSANVISNINGAR
Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada.
Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och
känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av
varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna
anordning.
SPARA DESSA ANVISNINGAR
Draft - Not Final Version
24
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Translated Safety Warnings
Aviso
INSTRUÇÕES IMPORTANTES DE SEGURANÇA
Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões
corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os
circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o
número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de
segurança traduzidos que acompanham o dispositivo.
GUARDE ESTAS INSTRUÇÕES
Advarsel
VIGTIGE SIKKERHEDSANVISNINGER
Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for
legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de
involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til
undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de
oversatte advarsler, der fulgte med denne enhed.
GEM DISSE ANVISNINGER
Draft - Not Final Version
25
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Translated Safety Warnings
Draft - Not Final Version
26
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Translated Safety Warnings
Statement 19—TN Power Warning
Warning
The device is designed to work with TN power systems.
Waarschuwing
Het apparaat is ontworpen om te functioneren met TN energiesystemen.
Varoitus
Koje on suunniteltu toimimaan TN-sähkövoimajärjestelmien yhteydessä.
Attention
Ce dispositif a été conçu pour fonctionner avec des systèmes d'alimentation TN.
Warnung
Das Gerät ist für die Verwendung mit TN-Stromsystemen ausgelegt.
Avvertenza
Il dispositivo è stato progettato per l’uso con sistemi di alimentazione TN.
Advarsel
Utstyret er utfomet til bruk med TN-strømsystemer.
Draft - Not Final Version
27
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Translated Safety Warnings
Statement 23—ISDN Connection Warning
Aviso
O dispositivo foi criado para operar com sistemas de corrente TN.
¡Advertencia!
El equipo está diseñado para trabajar con sistemas de alimentación tipo TN.
Varning!
Enheten är konstruerad för användning tillsammans med elkraftssystem av TN-typ.
Warning
The ISDN connection is regarded as a source of voltage that should be inaccessible to user contact.
Do not attempt to tamper with or open any public telephone operator (PTO)-provided equipment or
connection hardware. Any hardwired connection (other than by nonremovable,
connect-one-time-only plug) must be made only by PTO staff or suitably trained engineers.
Waarschuwing
De verbinding met ISDN (Integrated Services Digital Network = Digitaal netwerk met geïntegreerde
faciliteiten) wordt beschouwd als een spanningsbron die ontoegankelijk dient te zijn voor
gebruikers. Gebruikers dienen geen poging te doen om door de openbare telefoondienst (PTT)
verstrekte apparatuur of aansluitingshardware te openen of ermee te knoeien. Alle vastbedrade
verbindingen (behalve die verbindingen die gemaakt zijn door een niet-verwijderbare, slechts
eenmaal te verbinden stekker) dienen slechts door PTT-personeel of door daartoe opgeleide
ingenieurs gemaakt te worden.
Varoitus
ISDN-liitäntää pidetään jännitelähteenä, jonka kanssa käyttäjän ei tulisi päästä kosketuksiin.
Käyttäjien ei tulisi yrittää peukaloida tai avata laitteita tai liittimiä, jotka kuuluvat yleiselle
puhelinlaitokselle (PTO). Ainoastaan yleisen puhelinlaitoksen henkilökunnan tai ammattitaitoisten
teknikoiden tulee tehdä kaapeliliitännät (lukuun ottamatta kiinteitä pistokkeita, jotka yhdistetään
ainoastaan yhden kerran).
Draft - Not Final Version
28
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Translated Safety Warnings
Attention
La connexion du réseau numérique intégré (Integrated Services Digital Network ou ISDN) constitue
une source de tension qui ne doit pas être accessible à l'utilisateur. Les utilisateurs ne doivent
jamais tenter de modifier ni même d'ouvrir un matériel fourni par une compagnie de téléphone
public, ou le matériel de connexion. Toute connexion câblée (autre que celles établies par une prise
non démontable à connexion unique) ne doit être effectuée que par le personnel de la compagnie de
téléphone ou par des techniciens proprement formés.
Warnung
Die ISDN-Verbindung gilt als eine Spannungsquelle, die dem Anwender unzugänglich sein sollte.
Anwender sollten nicht versuchen, sich an der von den Anbietern öffentlicher TK-Dienste
gelieferten Ausstattung oder Verbindungs-Hardware zu schaffen zu machen oder sie zu öffnen. Alle
festverdrahteten Verbindungen (mit Ausnahme der Verbindungen mit einem nicht abnehmbaren, nur
einmal anzuschließenden Stecker) sind von Mitarbeitern des TK-Anbieters oder von entsprechend
geschulten Technikern herzustellen.
Avvertenza
Il collegamento ISDN (Integrated Services Digital Network - Rete digitale a servizi integrati) viene
considerato come una fonte di tensione che dovrebbe essere inaccessibile al contatto dell’utente.
Gli utenti non devono né manomettere né provare ad aprire le apparecchiature o i dispositivi di
collegamento forniti dalla società telefonica. Qualsiasi collegamento cablato (ad eccezione di una
spina non rimovibile, da installare una sola volta) deve essere eseguito esclusivamente da un
dipendente della società telefonica o da tecnici specializzati.
Advarsel
ISDN-koblingen betraktes som en spenningskilde som bør være utilgjengelig for brukeren. Brukere
bør ikke klusse med eller åpne utstyr eller tilkoblingsmateriale som er utstyrt av Telenor. Eventuelle
faste installasjoner (bortsett fra koblinger som er foretatt med et støpsel for engangsbruk og som
ikke kan fjernes) må kun utføres av Telenor-montører.
Aviso
A conexão RDIS (Rede Digital com Integração de Serviços) é interpretada como uma fonte de tensão
que deverá ser inacessível ao utilizador. Os utilizadores não deverão tentar violar qualquer
equipamento ou conexão de serviço telefónico público. Qualquer conexão de rede de fios (para
além daquela estabelecida por uma ficha não-removível de ligação única), deverá apenas ser
efectuada por pessoal dos serviços telefónicos ou engenheiros devidamente treinados.
¡Advertencia!
La conexión al circuito RDSI (Red Digital de Servicios Integrados) se considera como una fuente de
voltaje con la cual el usuario no debe entrar en contacto. Los usuarios deberán evitar manipular
indebidamente, o abrir, los equipos o hardware de conexión proporcionados por cualquier
compañía operadora de la red pública de telefonía. Las conexiones de cable rígido que sean
necesarias (excepto las de clavija no desmontable de un solo uso) deberán ser realizadas
exclusivamente por personal de la entidad operadora de la red pública de telefonía, o por personal
técnico adecuadamente capacitado.
Varning!
ISDN-anslutningen betraktas som en spänningskälla och bör inte vara åtkomlig för användaren
(ISDN: Integrated Services Digital Network = digitalt flertjänstnät). Användare får inte manipulera
eller söka öppna utrustning eller anslutningsdon som tillhandahållits av telefonbolag
(PTO-produkter). Anslutning av ledningar (med undantag av en icke löstagbar propp för
engångsanslutning) får endast utföras av PTO-anställda eller lämpligt utbildade tekniker.
Draft - Not Final Version
29
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Translated Safety Warnings
Statement 43—Jewelry Removal Warning
Warning
Before working on equipment that is connected to power lines, remove jewelry (including rings,
necklaces, and watches). Metal objects will heat up when connected to power and ground and can
cause serious burns or weld the metal object to the terminals.
Waarschuwing
Alvorens aan apparatuur te werken die met elektrische leidingen is verbonden, sieraden (inclusief
ringen, kettingen en horloges) verwijderen. Metalen voorwerpen worden warm wanneer ze met
stroom en aarde zijn verbonden, en kunnen ernstige brandwonden veroorzaken of het metalen
voorwerp aan de aansluitklemmen lassen.
Varoitus
Ennen kuin työskentelet voimavirtajohtoihin kytkettyjen laitteiden parissa, ota pois kaikki korut
(sormukset, kaulakorut ja kellot mukaan lukien). Metalliesineet kuumenevat, kun ne ovat
yhteydessä sähkövirran ja maan kanssa, ja ne voivat aiheuttaa vakavia palovammoja tai hitsata
metalliesineet kiinni liitäntänapoihin.
Attention
Avant d’accéder à cet équipement connecté aux lignes électriques, ôter tout bijou (anneaux,
colliers et montres compris). Lorsqu’ils sont branchés à l’alimentation et reliés à la terre, les objets
métalliques chauffent, ce qui peut provoquer des blessures graves ou souder l’objet métallique aux
bornes.
Warnung
Vor der Arbeit an Geräten, die an das Netz angeschlossen sind, jeglichen Schmuck (einschließlich
Ringe, Ketten und Uhren) abnehmen. Metallgegenstände erhitzen sich, wenn sie an das Netz und die
Erde angeschlossen werden, und können schwere Verbrennungen verursachen oder an die
Anschlußklemmen angeschweißt werden.
Avvertenza
Prima di intervenire su apparecchiature collegate alle linee di alimentazione, togliersi qualsiasi
monile (inclusi anelli, collane, braccialetti ed orologi). Gli oggetti metallici si riscaldano quando
sono collegati tra punti di alimentazione e massa: possono causare ustioni gravi oppure il metallo
può saldarsi ai terminali.
Draft - Not Final Version
30
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Translated Safety Warnings
Advarsel
Fjern alle smykker (inkludert ringer, halskjeder og klokker) før du skal arbeide på utstyr som er
koblet til kraftledninger. Metallgjenstander som er koblet til kraftledninger og jord blir svært varme
og kan forårsake alvorlige brannskader eller smelte fast til polene.
Aviso
Antes de trabalhar em equipamento que esteja ligado a linhas de corrente, retire todas as jóias que
estiver a usar (incluindo anéis, fios e relógios). Os objectos metálicos aquecerão em contacto com
a corrente e em contacto com a ligação à terra, podendo causar queimaduras graves ou ficarem
soldados aos terminais.
¡Advertencia!
Antes de operar sobre equipos conectados a líneas de alimentación, quitarse las joyas (incluidos
anillos, collares y relojes). Los objetos de metal se calientan cuando se conectan a la alimentación
y a tierra, lo que puede ocasionar quemaduras graves o que los objetos metálicos queden soldados
a los bornes.
Varning!
Tag av alla smycken (inklusive ringar, halsband och armbandsur) innan du arbetar på utrustning som
är kopplad till kraftledningar. Metallobjekt hettas upp när de kopplas ihop med ström och jord och
kan förorsaka allvarliga brännskador; metallobjekt kan också sammansvetsas med kontakterna.
Draft - Not Final Version
31
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Translated Safety Warnings
Statement 94—Wrist Strap Warning
Warning
During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly
touch the backplane with your hand or any metal tool, or you could shock yourself.
Waarschuwing
Draag tijdens deze procedure aardingspolsbanden om te vermijden dat de kaart beschadigd wordt
door elektrostatische ontlading. Raak het achterbord niet rechtstreeks aan met uw hand of met een
metalen werktuig, omdat u anders een elektrische schok zou kunnen oplopen.
Varoitus
Käytä tämän toimenpiteen aikana maadoitettuja rannesuojia estääksesi kortin vaurioitumisen
sähköstaattisen purkauksen vuoksi. Älä kosketa taustalevyä suoraan kädelläsi tai metallisella
työkalulla sähköiskuvaaran takia.
Attention
Lors de cette procédure, toujours porter des bracelets antistatiques pour éviter que des décharges
électriques n’endommagent la carte. Pour éviter l’électrocution, ne pas toucher le fond de panier
directement avec la main ni avec un outil métallique.
Warnung
Zur Vermeidung einer Beschädigung der Karte durch elektrostatische Entladung während dieses
Verfahrens ein Erdungsband am Handgelenk tragen. Bei Berührung der Rückwand mit der Hand oder
einem metallenen Werkzeug besteht Elektroschockgefahr.
Avvertenza
Durante questa procedura, indossare bracciali antistatici per evitare danni alla scheda causati da
un’eventuale scarica elettrostatica. Non toccare direttamente il pannello delle connessioni, né con
le mani né con un qualsiasi utensile metallico, perché esiste il pericolo di folgorazione.
Draft - Not Final Version
32
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Translated Safety Warnings
Statement 119—Unit Short Circuit Protection
Advarsel
Bruk jordingsarmbånd under prosedyren for å unngå ESD-skader på kortet. Unngå direkte berøring
av bakplanet med hånden eller metallverktøy, slik at di ikke får elektrisk støt.
Aviso
Durante este procedimento e para evitar danos ESD causados à placa, use fitas de ligação à terra
para os pulsos. Para evitar o risco de choque eléctrico, não toque directamente na parte posterior
com a mão ou com qualquer ferramenta metálica.
¡Advertencia!
Usartiras conectadas a tierra en las muñecas durante este procedimiento para evitar daños en la
tarjeta causados por descargas electrostáticas. No tocar el plano posterior con las manos ni con
ninguna herramienta metálica, ya que podría producir un choque eléctrico.
Varning!
Använd jordade armbandsremmar under denna procedur för att förhindra elektrostatisk skada på
kortet. Rör inte vid baksidan med handen eller metallverktyg då detta kan orsaka elektrisk stöt.
Warning
This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure
that a fuse or circuit breaker no larger than 120VAC, 20A U.S. (240VAC, 16 to 20A international) is used
on the phase conductors (all current-carrying conductors). The fuse or circuit breaker must have
adequate safety approval recognized by the country of usage.
Waarschuwing
Dit product is afhankelijk van de installatie van het gebouw voor bescherming tegen kortsluiting
(overstroom). Zorg ervoor dat de zekering of stroomonderbreker die gebruikt wordt niet groter is dan
120 V~, 20 ampère in de V.S. of 240 V~, 16-20 ampère internationaal op de fasegeleiders (alle
stroomdragende geleiders). De zekering of stroomonderbreker dient de juiste
veiligheidsgoedkeuringen te hebben in het land waarin het gebruikt wordt.
Draft - Not Final Version
33
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Translated Safety Warnings
Varoitus
Tämä tuote on riippuvainen rakennuksen oikosulkusuojauksesta (ylivirtasuojauksesta). Varmista,
että vaihejohtimissa (kaikissa jännitteellisissä johtimissa) käytetään alle 240 V vaihtovirran,
16–20 ampeerin (kansainvälinen) tai 120 V vaihtovirran, 20 ampeerin (Yhdysvallat) sulaketta tai
virtakytkintä. Sulakkeessa tai virtakytkimessä on oltava käyttömaassa tunnistetut, riittävät
turvahyväksynnät.
Attention
Pour la protection contre les courts-circuits (surtension), ce produit utilise les dispositifs intégrés
au bâtiment. Assurez-vous qu'un fusible ou un disjoncteur est utilisé sur les conducteurs de phase
(tous les conducteurs porteurs de courant). Le fusible ou le disjoncteur (maximum 240 V CA, 16 à 20 A
[aux USA, maximum 120 V CA, 20 A]) doit être conforme aux normes de sécurité en vigueur dans votre
pays.
Warnung
Diese Produkt erfordert eine Gebäudeabsicherung gegen Kurzschluß (Überstrom). Achten Sie
darauf, daß auf den Phasenleitern (allen stromführenden Leitern) eine Sicherung oder ein
Schaltkreisunterbrecher verwendet wird, der nicht größer ist als 120VAC, 20A U.S. (240VAC, 16 bis
20A international). Die Sicherung oder der Schaltkreisunterbrecher muß angemessenen
Sicherheitsvorschriften genügen, die den Bestimmungen des Anwendungslandes entsprechen.
Avvertenza
La protezione di questo prodotto da cortocircuiti (sovracorrente) dipende dall'impianto elettrico
dell’edificio. Assicuratevi che un fusibile o interruttore di circuito con meno di 120VAC, 20A U.S.
(240VAC, da 16 a 20A internazionale) venga utilizzato sui conduttori di fase (tutti i conduttori di
corrente elettrica). Il fusibile o interruttore di circuito deve rispondere alle specifiche di sicurezza
invigore nel paese dove viene utilizzato.
Advarsel
Dette produktet er avhengig av bygningens installasjoner for overstrømsbeskyttelse (kortslutning).
Kontroller at det ikke brukes en sikring eller overbelastningsbryter som er større enn 120 V,
20 ampere i USA, eller 240 V, 16 til 20 ampere internasjonalt, på faselederne (alle strømførende
ledere). Sikringen eller overbelastningsbryteren må være sikkerhetsgodkjent i det aktuelle landet
der den skal brukes.
Aviso
Este dispositivo depende das instalações existentes para protecção contra curto-circuitos
(sobrecarga). Assegure-se de que utiliza um fusível ou um disjuntor com uma capacidade não
superior a 120VAC, 20A U.S. (240VAC, 16 a 20A internacional) nos condutores de fase (todos os
condutores de corrente). O fusível ou disjuntor deverá possuir as necessárias aprovações de
segurança por parte das autoridades locais.
¡Advertencia!
Este producto ha sido diseñado teniendo en cuenta que la instalación del edificio contará con
protección contra cortocircuitos (sobrevoltajes). Asegúrese de que se usa un fusible o
cortacircuitos no superior a 120VAC, 20A en los EE.UU. (240VAC, de 16 a 20A en el resto de países)
en los conductores de fase (todos los conductores de transporte corriente). El fusible o
cortacircuitos debe contar con las aprobaciones de seguridad adecuadas y reconocidas por el país
en el que vayan a usarse.
Varning!
Denna produkt förlitar sig på att byggnadens installation är försedd med skydd mot kortslutning
(överström). Se till att en säkring eller ett överspänningsskydd för högst 120 V~, 20 A USA (240 V~,
16 – 20 A internationellt) används på fasledarna (alla strömförande ledare). Säkringen eller
överspänningsskyddet måste ha fullgoda säkerhetstillstånd som erkänns av användningslandet.
Draft - Not Final Version
34
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Translated Safety Warnings
Statement 150—Power Off Before Working on System
Warning
Before working on a system that has a standby/off switch, turn off the power by pressing the power
switch to standby and unplug the power cord.
Waarschuwing
Alvorens aan een systeem met een standby/uit-schakelaar te werken dient u de voeding uit te
schakelen door de voedingsschakelaar op standby te zetten en het voedingssnoer te verwijderen.
Varoitus
Katkaise virta valmiustila/virtakytkimellä varustetusta laitteesta ennen sen käyttämistä painamalla
virtakytkin valmiusasentoon ja irrottamalla sähköjohto.
Attention
Avant d'utiliser un système équipé d'un commutateur « Standby/Off » (pause/arrêt), coupez
l'alimentation en plaçant le commutateur sur la position Standby et débranchez le cordon
d'alimentation.
Warnung
Bevor Sie an einem System mit einem Bereit-/Aus-Schalter arbeiten, stellen Sie den Strom ab, indem
Sie den Stromschalter auf "Bereit" stellen und das Stromkabel herausziehen.
Avvertenza
Prima di lavorare su un sistema con interruttore attesa/off, spegnetelo premendo il pulsante sulla
posizione di attesa e staccate la spina elettrica.
Advarsel
Før det utføres arbeid på et system som har en standby/av-bryter, skal strømmen slås av ved å skyve
av/på-bryteren til standby og trekke ut strømledningen.
Aviso
Antes de começar a trabalhar num sistema com um interruptor standby (posição de espera)/off
(desligado), desligue a corrente eléctrica colocando o interruptor na posição standby e retire o cabo
de alimentação da tomada.
¡Advertencia!
Antes de empezar a trabajar con un sistema cuyo interruptor incluya la posición standby, cierre la
corriente posicionando el interruptor a standby y a continuación desconecte el cable eléctrico.
Varning!
Innan du arbetar på ett system med en standby-/strömbrytaromkopplare, slå av strömmen genom att
ställa omkopplaren på standby och koppla ur nätsladden.
Draft - Not Final Version
35
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Translated Safety Warnings
Statement 151—ISDN Network Voltages Warning
Warning
Network hazardous voltages are present in the ISDN cable. If you detach the ISDN cable, detach the
end away from the router first to avoid possible electric shock. Network hazardous voltages also are
present on the system card in the area of the ISDN port (RJ-45 connector), regardless of when power
is turned off (by pressing power switch to standby).
Waarschuwing
De ISDN-kabel bevat voltages die gevaar voor het netwerk opleveren. Als de ISDN-kabel verwijderd
moet worden, verwijdert u om mogelijke elektrische schokken te vermijden eerst het uiteinde dat
niet op de router is aangesloten. Verder bevat tevens de systeemkaart in de buurt van de ISDN-poort
(RJ-45-aansluiting) voltages die gevaar voor het netwerk opleveren, onafhankelijk van wanneer de
voeding wordt uitgeschakeld (door de voedingsschakelaar op standby te zetten).
Varoitus
ISDN-johdossa on verkolle vaarallisia jännitteitä. Jos ISDN-kaapeli irrotetaan, irrota ensin
reitittimen puoleinen pää sähköiskun välttämiseksi. Verkolle vaarallisia jännitteitä on myös
järjestelmäkortissa ISDN-portin alueella (RJ-45-liitin), vaikka virta olisikin katkaistu painamalla
virtakytkin valmiusasentoon.
Attention
Des tensions électriques réseau dangereuses circulent sur le câble RNIS. Pour éviter tout risque de
choc électrique lorsque vous débranchez ce câble, déconnectez d'abord l'extrémité non raccordée
au routeur. Par ailleurs, des tensions dangereuses sont également présentes autour du port RNIS
(connecteur RJ-45) de la carte système, que le système soit sous tension ou hors tension
(commutateur d'alimentation sur « Standby »).
Warnung
Auf dem ISDN-Kabel herrschen gefährliche Spannungen. Bei Entfernung des ISDN-Kabels muß
zuerst das Kabel von der Routerseite her abgetrennt werden, um einen möglichen elektrischen
Schlag zu vermeiden. Gefährliche Spannungen herrschen darüber hinaus auf der Systemkarte im
Bereich des ISDN-Ports (RJ-45 Steckverbinder) und zwar unabhängig davon, ob der Strom (durch
Umlegung des Stromschalters auf "Bereit") abgeschaltet ist.
Avvertenza
Sono presenti dei voltaggi elettrici rete pericolosi nei cavi ISDN. Se staccate il cavo ISDN, dovete
prima staccare l'estremità collegata al router per evitare scosse elettriche. Pericolose tensioni
elettriche rete sono presente anche sulla scheda del sistema vicino alla porta ISDN (connettore
RJ-45) a prescindere da quando sia stata spenta l'alimentazione elettrica (premendo il pulsante
sulla posizione di attesa).
Advarsel
Livsfarlig spenning er til stede i nettverkets ISDN-kabel. Hvis du kobler fra ISDN-kabelen, skal
enden som vender bort fra ruteren, kobles fra først for å unngå mulig elektrisk støt. Livsfarlig
spenning er også til stede på nettverkets systemkort i området ved ISDN-utgangen (RJ-45-kobingen),
uten hensyn til når strømmen er slått av (ved å skyve strømbryteren til standby).
Aviso
Existem tensões de rede perigosas no cabo de Rede Digital com Integração de Serviços-RDIS
(ISDN-Integrated Services Digital Network). Se for desligar o cabo RDIS, desligue primeiro a
extremidade oposta à do comutador para evitar possíveis choques eléctricos. Existem tensões de
rede perigosas também na placa do sistema, nomeadamente, na área da porta RDIS (conector RJ-45),
independentemente do facto da corrente estar desligada (ao colocar o interruptor em standby)
ou não.
Draft - Not Final Version
36
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Translated Safety Warnings
Statement 162—EU Public Network Port Warning
¡Advertencia!
Las líneas RSDI contienen voltajes peligrosos de la red. Si desconecta el cable RSDI, separe
primero el final del router para evitar posibles choques eléctricos. La tarjeta del sistema en el área
del puerto RSDI (conector RJ-45) también contiene altos voltajes de la red, independientemente de
si está apagada (posicionando el interruptor de la corriente a standby).
Varning!
I ISDN-kabeln förekommer spänningar som är farliga för nätverk. Om du kopplar ur ISDN-kabeln,
undvik eventuell elstöt genom att först koppla ur den ände som är längst bort ifrån routern.
Spänningar som är farliga för nätverk förekommer också på systemkortet i området intill
ISDN-porten (RJ-45-koppling), oberoende av när strömmen slås av (genom att ställa omkopplaren på
standby).
Warning
If the symbol of suitability with an overlaid cross appears above a port, you must not connect the
port to a public network that follows the European Union standards. Connecting the port to this type
of public network can cause severe injury or damage your router.
Waarschuwing
Als er een geschiktheidsymbool met een overgetrokken kruis boven een poort aanwezig is, dan mag
u deze poort niet op een openbaar netwerk aansluiten dat aan de normen van de Europese Unie
voldoet. Als u de poort op een dergelijk openbaar netwerk aansluit, kan dit ernstig letsel of schade
aan uw router-eenheid veroorzaken.
Varoitus
Jos portin päälle ilmestyy soveltuvuussymboli, jonka päällä on rasti, porttia ei saa liittää Euroopan
unionin standardien mukaiseen julkiseen verkkoon. Jos portti liitetään tällaiseen julkiseen
verkkoon, seurauksena voi olla henkilö- tai reititinvaurio.
Attention
Pour éviter tout risque d'accident corporel et/ou de dommage matériel, si le symbole de capacité
barré d'une croix apparaît au-dessus d'un port, il est vivement recommandé de ne pas connecter ce
port à un réseau public aux normes de l'Union Européenne.
Warnung
Wenn oberhalb des Ports das Verträglichkeitssymbol mit einem Kreuz darüber erscheint, dürfen Sie
den Port nicht an ein öffentliches Netzwerk anschließen, daß den Standards der Europäischen
Gemeinschaft folgt. Das Anschließen des Port an ein solches Netzwerk kann zu schweren
Verletzungen führen oder Ihren Router beschädigen.
Avvertenza
Se su una porta compare il simbolo di idoneità sbarrato, significa che la porta non può essere
collegata a una rete pubblica a norma UE. Collegando la porta a un simile tipo di rete pubblica si
possono correre seri rischi e provocare danni al proprio router.
Advarsel
Hvis symbolet for anvendelse med et kryss over vises over en utgang, skal utgangen ikke kobles til
et offentlig nettverk som følger EU-standardene. Hvis utgangen kobles til denne typen offentlig
nettverk, kan det medføre alvorlig personskade eller skade på ruteren.
Aviso
Se o símbolo de adequação com uma cruz sobreposta aparecer acima de uma porta, não conectar a
porta a uma rede pública que obedece aos padrões da União Europeia. A conexão da porta a este
tipo de rede pública pode causar avarias ou danos severos ao seu distribuidor.
Draft - Not Final Version
37
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Translated Safety Warnings
Statement 199—Emergency Access Warning
¡Advertencia!
Si aparece el símbolo de idoneidad con una cruz sobrepuesta encima de un puerto, no debe conectar
el puerto a una red pública que siga los estándares de la Unión Europea. Si conecta el puerto a este
tipo de red pública puede lesionarse o dañar su router.
Varning!
Om lämplighetssymbolen med ett överlagt kors visas ovanför en port, får porten inte anslutas till ett
offentligt nätverk av EU-standard. Om porten ansluts till denna typ av offentligt nätverk kan det
förorsaka allvarlig personskada eller skada på routern.
Warning
This equipment is not designed for making emergency telephony calls when the power fails.
Alternative arrangements should be made for access to emergency services. Access to emergency
services can be affected by any call-barring function of this equipment.
Waarschuwing
Deze apparatuur is niet bedoeld voor noodtelefoongesprekken bij stroomstoringen. Voor
telefoondiensten in noodsituaties moet u andere maatregelen treffen. Eventuele
blokkeringsfuncties van deze apparatuur kunnen van invloed zijn op de bereikbaarheid van deze
telefoondiensten.
Varoitus
Tätä laitetta ei voi käyttää hätäpuheluihin, jos sähkövirta on katkennut. Käytettävissä täytyy olla
vaihtoehtoinen järjestelmä yhteyden saamiseksi hälytyskeskukseen. Hälytyskeskusyhteyden
estymiseen voi vaikuttaa mikä tahansa tämän laitteiston soitonestotoiminto.
Attention
Cet équipement n’est pas conçu pour les télécommunications d’urgence en cas de panne
d’électricité et il importe de prévoir d'autres moyens d'accès aux services d'urgence. Cependant,
toute fonction d'interdiction d'appel de cet équipement risque d'avoir une incidence sur l'accès aux
services d'urgence.
Warnung
Dieses Gerät ist nicht geeignet für Notruftelefonate, wenn die Stromzufuhr ausfällt. Für das
Kontaktieren von Notfalldiensten sollten alternative Maßnahmen geplant werden. Das Kontaktieren
von Notfalldiensten kann von jeder der anrufsperrenden Funktionen dieses Gerätes beeinträchtigt
werden.
Avvertenza
Questo apparecchio non è predisposto per effettuare chiamate d’emergenza nel caso dimancanza di
alimentazione di corrente. È necessario pertanto predisporre misure alternative per consentire
l’accesso ai servizi di emergenza. Tale accesso può essere inoltre influenzato dalle funzioni di
blocco presenti sull’apparechio stesso.
Advarsel
Dette utstyret har ingen funksjon for nødtjenester når strømmen er brutt. En bør utarbeide alternative
ordninger hvis man må ha tilgang til nødtjenester. Tilgangen til nødtjenester kan bli påvirket av alle
samtalesperrende funksjoner i dette utstyret.
Aviso
Este equipamento não foi concebido para estabelecer chamadas telefónicas de emergência quando
faltar a energia. Devem tomar-se medidas alternativas para aceder a serviços de emergência. O
acesso aos serviços de emergência pode ser afectado por qualquer função de barramento de
chamadas aplicada a este equipamento.
Draft - Not Final Version
38
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Translated Safety Warnings
Statement 242—Equipment Grounding Warning
¡Advertencia!
Este equipo no está diseñado para efectuar llamadas telefónicas de emergencia en caso de que falle
la alimentación. Se deberán tomar medidas alternativas para acceder a servicios de emergencia. El
acceso a servicios de emergencia puede verse afectado por cualquier función de bloqueo de
llamadas que pueda tener este equipo.
Varning!
Denna utrustning är inte utformad för telefonsamtal i nödläge när strömmen bryts. Andra
arrangemang måste göras för att kunna nå nödtjänster. Åtkomst till nödtjänster kan påverkas av alla
samtalsspärrningsfunktioner i denna utrustning.
Warning
This equipment needs to be grounded. Use a green and yellow 12 to 14 AWG ground wire to connect
the host to earth ground during normal use.
Waarschuwing
Deze apparatuur hoort geaard te worden. Gebruik een groen/gele 12 - 14 AWG aarddraad om de host
tijdens normaal gebruik met de aarde te verbinden.
Varoitus
Tämä laitteisto täytyy maadoittaa. Yhdistä isäntälaite maahan normaalikäytön aikana käyttämällä
vihreä-keltaista 12 - 14 AWG -maadoitusjohtoa.
Attention
Cet équipement doit être relié à la terre. Utilisez un fil vert et jaune de gabarit 12 à 14 (AWG) pour
connecter l'hôte à la terre lors de son utilisation normale.
Warnung
Dieses Gerät muß geerdet werden. Verwenden Sie ein grün/gelbes 12 bis 14-AWG-Erdungskabel, um
damit das Host-Gerät während des normalen Betriebs zu erden.
Avvertenza
Questa apparecchiatura deve essere collegata a massa. Durante l'uso normale, collegare l'host alla
massa di terra usando un filo di massa verde e giallo di diametro compreso tra 12 e 14 AWG.
Advarsel
Dette utstyret krever jording. Bruk grønn og gul 12-14 AWG jordingsledning til å kople
vertsterminalen til jording ved normal bruk.
Aviso
É necessário que este equipamento esteja ligado à terra. Utilize um fio de ligação à terra de 12 a 14
AWG, verde e amarelo, para ligar o host à ligação à terra durante a sua utilização normal.
¡Advertencia!
Este equipo debe conectarse a tierra. Utilizar un hilo de puesta a tierra entre 12 y 14 AWG verde y
amarillo para conectar a tierra el equipo principal durante el uso normal.
Varning!
Denna utrustning är avsedd att jordas. Använd en gulgrön jordledning av storlek 12 till 14 AWG till
att jorda värdenheten vid normal användning.
Draft - Not Final Version
39
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Translated Safety Warnings
Statement 332—Antenna Installation Warning
This warning applies only to Cisco 850 series and Cisco 870 series routers.
Warning
In order to comply with FCC radio frequency (RF) exposure limits, antennas should be located at a
minimum of 7.9 inches (20 cm) or more from the body of all persons.
Waarschuwing
Om te voldoen aan de FCC radiofrequentie (RF) blootstellingslimieten dienen antennes zich minstens
20 cm of meer van de lichamen van alle personen bevinden.
Varoitus
FCC:n antamien radiotaajuuksille altistumista koskevien rajoitusten mukaan antennien on sijaittava
vähintään 20 cm:n päässä kaikista henkilöistä.
Attention
Pour se conformer aux limites d'exposition à la fréquence radio préconisées par la FCC (Federal
Communications Commission), les antennes doivent se situer à un minimum de 20 cm de toute
personne.
Warnung
Um die in den FCC-Richtlinien festgelegten Expositionshöchstgrenzen für Radiofrequenzen (RF)
nicht zu überschreiten, sollten Antennen mindestens 20 cm entfernt von Personen aufgestellt
werden.
Avvertenza
Per conformarsi ai limiti FCC di esposizione a radiofrequenza (RF), le antenne devono stare ad una
distanza minima di 20 cm dal corpo di ogni persona.
Advarsel
I henhold til eksponeringsgrensene for radiofrekvenser (RF), skal antenner befinne seg på en
avstand av minst 20 cm eller mer fra mennesker.
Aviso
Para estar de acordo com as normas FCC de limites de exposição para freqüência de rádio (RF), as
antenas devem estar distantes no mínimo 20 cm (7,9 pol) do corpo de qualquer pessoa.
¡Advertencia!
Para cumplir con los límites de exposición de radio frecuencia (RF) de la Comisión Federal de
Comunicaciones (FCC) es preciso ubicar las antenas a un mínimo de 20 cm (7,9 pulgadas) o más del
cuerpo de las personas.
Varning!
För att följa FCC-exponeringsgränserna för radiofrekvens (RF), bör antenner placeras på minst 20 cm
avstånd från alla människor.
Draft - Not Final Version
40
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Translated Safety Warnings
Statement 353—This Product Must be Connected
Warning
This product must be connected to a power-over-ethernet (PoE) IEEE 802.3af compliant power source
or an IEC60950 compliant limited power source.
Waarschuwing
Dit product moet worden verbonden met een stroomvoorziening die compatibel is met PoE
(power-over-ethernet) IEEE 802.3af of een beperkte stroomvoorziening die compatibel is met
IEC60950.
Varoitus
Tämä tuote on liitettävä PoE (power-over-ethernet) IEEE 802.3af -yhteensopivaan virtalähteeseen tai
IEC60950-yhteensopivaan rajoitettuun virtalähteeseen.
Attention
Ce produit doit être connecté à une source d'alimentation électrique par câble Ethernet (PoE)
conforme à la norme IEEE 802.3af ou à une source d'alimentation limitée conforme à la norme
IEC60950.
Warnung
Dieses Produkt muss entweder an eine Stromquelle angeschlossen sein, die mit dem IEEE
802.3af-Standard Power-over-Ethernet (PoE) kompatibel ist oder an eine Stromquelle für geringe
Leistungen, die IEC60950-kompatibel ist.
Avvertenza
Questo prodotto deve essere connesso a una fonte di alimentazione di tipo PoE
(power-over-ethernet) conforme a IEEE 802.3af o a una fonte di alimentazione conforme a IEC60950.
Advarsel
Dette produktet må være koblet til en Power-over-Ethernet (PoE) IEEE 802.3af-kompatibel strømkilde
eller en IEC60950-kompatibel begrenset strømkilde.
Aviso
Este produto tem de estar ligado a uma fonte de alimentação compatível com a norma IEEE 802.3af,
também conhecida pela sigla Power over Ethernet (PoE), ou a uma fonte de alimentação limitada
compatível com a norma IEC60950.
¡Advertencia!
Debe conectar este producto a una fuente de alimentación en Ethernet (PoE) conforme con el
estándar IEEE 802.3af, o a una fuente limitada conforme con el estándar IEC60950.
Varning!
Denna produkt måste vara ansluten till en PoE IEEE 802.3af-kompatibel strömkälla eller en
IEC60950-kompatibel begränsad strömkälla.
Draft - Not Final Version
41
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Translated Safety Warnings
Statement 371—Power Cable and AC Adapter
Statement 373—Must Connect To An Indoor Antenna
Warning
When installing the product, please use the provided or designated connection cables/power
cables/AC adaptors/batteries. Using any other cables/adaptors could cause a malfunction or a fire.
Electrical Appliance and Material Safety Law prohibits the use of UL-certified cables (that have the
“UL” or “CSA” shown on the cord), not regulated with the subject law by showing “PSE” on the cord,
for any other electrical devices than products designated by CISCO.
Warning
This equipment must be connected to an indoor antenna only.
Waarschuwing
Deze apparatuur kan alleen worden aangesloten op een antenne voor binnengebruik.
Varoitus
Tämän laitteiston voi liittää vain sisäantenniin.
Attention
Cet équipement doit être connecté à une antenne intérieure uniquement.
Warnung
Diese Gerät darf nur an eine Innenantenne angeschlossen werden.
Avvertenza
Questo apparecchio può essere collegato solo a un'antenna da interno.
Advarsel
Dette utstyret må kun kobles til en innendørsantenne.
Aviso
Este equipamento só pode ser ligado a uma antena interior.
¡Advertencia!
Este equipo sólo debe estar conectado a una antena de interior.
Draft - Not Final Version
42
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Translated Safety Warnings
Statement 378—Read Wall-Mounting Instructions Before Installation
Varning!
Den här utrustningen får endast anslutas till en inomhusantenn.
Warning
Read the wall-mounting instructions carefully before beginning installation. Failure to use the
correct hardware or to follow the correct procedures could result in a hazardous situation to people
and damage to the system.
Waarschuwing
Lees de wandbevestigingsinstructies aandachtig door voordat u met de installatie begint. Het niet
gebruiken van de juiste hardware of het opvolgen van de juiste procedures kan resulteren in een
gevaarlijke situatie voor mensen en schade aan het systeem.
Varoitus
Lue seinäkiinnitysohjeet huolellisesti läpi ennen työn aloitusta. Mikäli kiinnityksessä ei käytetä
oikeanlaisia työkaluja tai ohjeita ei noudateta tarkasti, järjestelmä saattaa aiheuttaa vaaratilanteen
tai se voi vaurioitua.
Attention
Lisez les instructions de montage murale avec attention avant de commencer l'installation. Ne pas
utiliser le matériel correct ou ne pas suivre les procédures correctes pourrait donner résultat a une
situation dangereuse pour les utilisateurs et endommager le système.
Warnung
Bitte lesen Sie vor Beginn der Installierung die Anleitungen zur Wandmontage sorgfältig durch.
Verwendung von inkorrekter Apparatur oder Nichtbefolgung der vorgeschriebenen Methoden kann
zur Gefährdung von Personen oder Schaden am System führen.
Avvertenza
Leggere attentamente le istruzioni per il montaggio al muro prima di iniziare l'installazione. Un
errato uso del corretto hardware o il mancato rispetto delle corrette procedure potrebbe avere come
conseguenza una situazione di pericolo per le persone e danni al sistema.
Advarsel
Les nøye gjennom instruksene om veggmontering før du begynner monteringen. Dersom man ikke
bruker riktig maskinvare eller ikke følger riktig framgangsmåte kan det resultere i risiko for
personskader og skade på systemet.
Draft - Not Final Version
43
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Translated Safety Warnings
Statement 393—Explosive Device Proximity Wireless Network Device
Aviso
Leia com cuidado as instruções de montagem na parede antes de iniciar a instalação. Falha em usar
o hardware correto ou em seguir os procedimentos corretos pode resultar numa situação de risco
para as pessoas e danos ao sistema.
¡Advertencia!
Lea atentamente las instrucciones que se encuentran en la pared antes de comenzar con la
instalación. Si no utiliza el hardware correcto o no sigue los procedimientos correctos se podría
producir una situación peligrosa para las personas y daños al sistema.
Varning!
Läs väggmonteringsintruktionerna noga innan du påbörjar installationen. Försummelse av att inte
använda rätt hårdvara eller att inte föjla korrekt tillvägagångsätt kan resultera i en riskabel
situation för människor och kan skada systemet.
Warning
Do not operate your wireless network device near unshielded blasting caps or in an explosive
environment unless the device has been modified to be especially qualified for such use.
Waarschuwing
Gebruik dit draadloos netwerkapparaat alleen in de buurt van onbeschermde ontstekers of in een
omgeving met explosieven indien het apparaat speciaal is aangepast om aan de eisen voor een
dergelijk gebruik te voldoen.
Varoitus
Älä käytä johdotonta verkkolaitetta suojaamattomien räjäytysnallien läheisyydessä tai
räjäytysalueella, jos laitetta ei ole erityisesti muunnettu sopivaksi sellaiseen käyttöön.
Attention
Ne jamais utiliser un équipement de réseau sans fil à proximité d'un détonateur non blindé ou dans
un lieu présentant des risques d'explosion, sauf si l'équipement a été modifié à cet effet.
Draft - Not Final Version
44
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Translated Safety Warnings
Statement 1004—Installation Instructions
Warnung
Benutzen Sie Ihr drahtloses Netzwerkgerät nicht in der Nähe ungeschützter Sprengkapseln oder
anderer explosiver Stoffe, es sei denn, Ihr Gerät wurde eigens für diesen Gebrauch modifiziert und
bestimmt.
Avvertenza
Non utilizzare la periferica di rete senza fili in prossimità di un detonatore non protetto o di esplosivi
a meno che la periferica non sia stata modificata a tale proposito.
Advarsel
Ikke bruk den trådløse nettverksenheten nært inntil uisolerte fenghetter eller i et eksplosivt miljø
med mindre enheten er modifisert slik at den tåler slik bruk.
Aviso
Não opere o dispositivo de rede sem fios perto de cápsulas explosivas não protegidas ou num
ambiente explosivo, a não ser que o dispositivo tenha sido modificado para se qualificar
especialmente para essa utilização.
¡Advertencia!
No utilizar un aparato de la red sin cable cerca de un detonador que no esté protegido ni tampoco
en un entorno explosivo a menos que el aparato haya sido modificado con ese fin.
Varning!
Använd inte den trådlösa nätverksenheten i närheten av oskyddade tändhattar eller i en explosiv
miljö om inte enheten modifierats för att kunna användas i sådana sammanhang.
Warning
Read the installation instructions before connecting the system to the power source.
Waarschuwing
Raadpleeg de installatie-instructies voordat u het systeem op de voedingsbron aansluit.
Varoitus
Lue asennusohjeet ennen järjestelmän yhdistämistä virtalähteeseen.
Attention
Avant de brancher le système sur la source d'alimentation, consulter les directives d'installation.
Warnung
Vor dem Anschließen des Systems an die Stromquelle die Installationsanweisungen lesen.
Avvertenza
Consultare le istruzioni di installazione prima di collegare il sistema all'alimentatore.
Advarsel
Les installasjonsinstruksjonene før systemet kobles til strømkilden.
Aviso
Leia as instruções de instalação antes de ligar o sistema à fonte de energia.
¡Advertencia!
Lea las instrucciones de instalación antes de conectar el sistema a la red de alimentación.
Varning!
Läs installationsanvisningarna innan du kopplar systemet till strömförsörjningsenheten.
Draft - Not Final Version
45
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Translated Safety Warnings
Statement 1005—Circuit Breaker
Warning
This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure
that the protective device is rated not greater than:
120 VAC, 15A U.S. (240 VAC, 10A international)
Waarschuwing
Dit product is afhankelijk van de installatie van het gebouw voor beveiliging tegen kortsluiting
(overstroom). Controleer of de beschermingsinrichting niet meer dan:
120 VAC, 15A U.S. (240 VAC, 10A international) is.
Varoitus
Tämä tuote on riippuvainen rakennukseen asennetusta oikosulkusuojauksesta
(ylivirtasuojauksesta). Varmista, että suojalaitteen mitoitus ei ole yli:
120 VAC, 15A U.S. (240 VAC, 10A international)
Draft - Not Final Version
46
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Translated Safety Warnings
Attention
Pour ce qui est de la protection contre les courts-circuits (surtension), ce produit dépend de
l'installation électrique du local. Vérifiez que le courant nominal du dispositif de protection n'est
pas supérieur à :
120 VAC, 15A U.S. (240 VAC, 10A international)
Warnung
Dieses Produkt ist darauf angewiesen, dass im Gebäude ein Kurzschluss- bzw. Überstromschutz
installiert ist. Stellen Sie sicher, dass der Nennwert der Schutzvorrichtung nicht mehr als:
120 VAC, 15A U.S. (240 VAC, 10A international) beträgt.
Avvertenza
Questo prodotto dipende dall'impianto dell'edificio per quanto riguarda la protezione contro
cortocircuiti (sovracorrente). Assicurarsi che il dispositivo di protezione non abbia un rating
superiore a:
120 VAC, 15A U.S. (240 VAC, 10A international)
Advarsel
Dette produktet er avhengig av bygningens installasjoner av kortslutnings (overstrøm)-beskyttelse.
Påse at verneenheten ikke er merket høyere enn:
120 VAC, 15A U.S. (240 VAC, 10A international)
Aviso
Este produto depende das instalações existentes para proteção contra curto-circuito (sobrecarga).
Assegure-se de que o fusível ou disjuntor não seja superior a:
120 VAC, 15A U.S. (240 VAC, 10A international)
¡Advertencia!
Este equipo utiliza el sistema de protección contra cortocircuitos (o sobrecorrientes) del edificio. Asegúrese
de que el dispositivo de protección no sea superior a:
120 VAC, 15A U.S. (240 VAC, 10A international)
Varning!
Denna produkt är beroende av i byggnaden installerat kortslutningsskydd (överströmsskydd).
Kontrollera att skyddsanordningen inte har högre märkvärde än:
120 VAC, 15A U.S. (240 VAC, 10A international)
120 VAC, 15A U.S. (240 VAC, 10A international)
120 VAC, 15A U.S. (240 VAC, 10A international)
120 VAC, 15A U.S. (240 VAC, 10A international)
120 VAC, 15A U.S. (240 VAC, 10A international)
Draft - Not Final Version
47
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Translated Safety Warnings
Statement 1008—Class 1 Laser Product
Warning
Class 1 laser product.
Waarschuwing
Klasse-1 laser produkt.
Varoitus
Luokan 1 lasertuote.
Attention
Produit laser de classe 1.
Warnung
Laserprodukt der Klasse 1.
Avvertenza
Prodotto laser di Classe 1.
Advarsel
Laserprodukt av klasse 1.
Aviso
Produto laser de classe 1.
¡Advertencia!
Producto láser Clase I.
Varning!
Laserprodukt av klass 1.
Aviso
Produto a laser de classe 1.
Advarsel
Klasse 1 laserprodukt.
Draft - Not Final Version
48
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Translated Safety Warnings
Statement 1010—Staring into Laser Beam
Warning
Do not stare into the laser beam.
Waarschuwing
Niet in de straal staren.
Varoitus
Älä katso säteeseen.
Attention
Ne pas fixer le faisceau des yeux.
Warnung
Nicht direkt in den Strahl blicken.
Avvertenza
Non fissare il raggio con gli occhi.
Advarsel
Stirr ikke på strålen.
Aviso
Não olhe fixamente para o raio.
¡Advertencia!
No mirar fijamente el haz.
Varning!
Laserstrålning när enheten är öppen.
Draft - Not Final Version
49
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Translated Safety Warnings
Statement 1015—Battery Handling
Warning
There is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with
the same or equivalent type recommended by the manufacturer. Dispose of used batteries according
to the manufacturer’s instructions.
Waarschuwing
Er is ontploffingsgevaar als de batterij verkeerd vervangen wordt. Vervang de batterij slechts met
hetzelfde of een equivalent type dat door de fabrikant aanbevolen is. Gebruikte batterijen dienen
overeenkomstig fabrieksvoorschriften weggeworpen te worden.
Varoitus
Räjähdyksen vaara, jos akku on vaihdettu väärään akkuun. Käytä vaihtamiseen ainoastaan saman-
tai vastaavantyyppistä akkua, joka on valmistajan suosittelema. Hävitä käytetyt akut valmistajan
ohjeiden mukaan.
Attention
Danger d'explosion si la pile n'est pas remplacée correctement. Ne la remplacer que par une pile
de type semblable ou équivalent, recommandée par le fabricant. Jeter les piles usagées
conformément aux instructions du fabricant.
Warnung
Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie die Batterie nur durch
den gleichen oder vom Hersteller empfohlenen Batterietyp. Entsorgen Sie die benutzten Batterien
nach den Anweisungen des Herstellers.
Avvertenza
Pericolo di esplosione se la batteria non è installata correttamente. Sostituire solo con una di tipo
uguale o equivalente, consigliata dal produttore. Eliminare le batterie usate secondo le istruzioni
del produttore.
Advarsel
Det kan være fare for eksplosjon hvis batteriet skiftes på feil måte. Skift kun med samme eller
tilsvarende type som er anbefalt av produsenten. Kasser brukte batterier i henhold til produsentens
instruksjoner.
Aviso
Existe perigo de explosão se a bateria for substituída incorrectamente. Substitua a bateria por uma
bateria igual ou de um tipo equivalente recomendado pelo fabricante. Destrua as baterias usadas
conforme as instruções do fabricante.
¡Advertencia!
Existe peligro de explosión si la batería se reemplaza de manera incorrecta. Reemplazar la batería
exclusivamente con el mismo tipo o el equivalente recomendado por el fabricante. Desechar las
baterías gastadas según las instrucciones del fabricante.
Varning!
Explosionsfara vid felaktigt batteribyte. Ersätt endast batteriet med samma batterityp som
rekommenderas av tillverkaren eller motsvarande. Följ tillverkarens anvisningar vid kassering av
använda batterier.
Draft - Not Final Version
50
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Translated Safety Warnings
Statement 1016—Invisible Laser Radiation
Warning
Invisible laser radiation present.
Waarschuwing
Onzichtbare laserstraling aanwezig.
Varoitus
Näkymättömiä lasersäteitä.
Attention
Rayonnement laser actif mais invisible.
Warnung
Unsichtbare Laserstrahlung.
Avvertenza
Radiazione laser invisibile.
Advarsel
Usynlig laserstråling.
Aviso
Radiação laser invisível presente.
¡Advertencia!
Existe radiación láser invisible.
Varning!
Nu pågående osynlig laserstrålning.
Draft - Not Final Version
51
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Translated Safety Warnings
Statement 1021—SELV Circuit
Warning
To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to
telephone-network voltage (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain
TNV circuits. Some LAN and WAN ports both use RJ-45 connectors. Use caution when
connecting cables.
Waarschuwing
Om elektrische schokken te vermijden, mogen veiligheidscircuits met extra lage spanning
(genaamd SELV = Safety Extra-Low Voltage) niet met telefoonnetwerkspanning (TNV) circuits
verbonden worden. LAN (Lokaal netwerk) poorten bevatten SELV circuits en WAN (Regionaal
netwerk) poorten bevatten TNV circuits. Sommige LAN en WAN poorten gebruiken allebei RJ-45
connectors. Ga voorzichtig te werk wanneer u kabels verbindt.
Varoitus
Jotta vältyt sähköiskulta, älä kytke pienjännitteisiä SELV-suojapiirejä puhelinverkkojännitettä
(TNV) käyttäviin virtapiireihin. LAN-portit sisältävät SELV-piirejä ja WAN-portit
puhelinverkkojännitettä käyttäviä piirejä. Osa sekä LAN- että WAN-porteista käyttää
RJ-45-liittimiä. Ole varovainen kytkiessäsi kaapeleita.
Attention
Pour éviter une électrocution, ne raccordez pas les circuits de sécurité basse tension (Safety
Extra-Low Voltage ou SELV) à des circuits de tension de réseau téléphonique (Telephone Network
Voltage ou TNV). Les ports du réseau local (LAN) contiennent des circuits SELV et les ports du réseau
longue distance (WAN) sont munis de circuits TNV. Certains ports LAN et WAN utilisent des
connecteurs RJ-45. Raccordez les câbles en prenant toutes les précautions nécessaires.
Warnung
Zur Vermeidung von Elektroschock die Sicherheits-Kleinspannungs-Stromkreise (SELV-Kreise)
nicht an Fernsprechnetzspannungs-Stromkreise (TNV-Kreise) anschließen. LAN-Ports enthalten
SELV-Kreise, und WAN-Ports enthalten TNV-Kreise. Einige LAN- und WAN-Ports verwenden auch
RJ-45-Steckverbinder. Vorsicht beim Anschließen von Kabeln.
Avvertenza
Per evitare scosse elettriche, non collegare circuiti di sicurezza a tensione molto bassa (SELV) ai
circuiti a tensione di rete telefonica (TNV). Le porte LAN contengono circuiti SELV e le porte WAN
contengono circuiti TNV. Alcune porte LAN e WAN fanno uso di connettori RJ-45. Fare attenzione
quando si collegano cavi.
Advarsel
Unngå å koble lavspenningskretser (SELV) til kretser for telenettspenning (TNV), slik at du unngår
elektrisk støt. LAN-utganger inneholder SELV-kretser og WAN-utganger inneholder TNV-kretser. Det
finnes både LAN-utganger og WAN-utganger som bruker RJ-45-kontakter. Vær forsiktig når du
kobler kabler.
Draft - Not Final Version
52
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Translated Safety Warnings
Aviso
Para evitar choques eléctricos, não conecte os circuitos de segurança de baixa tensão (SELV) aos
circuitos de tensão de rede telefónica (TNV). As portas LAN contêm circuitos SELV e as portas WAN
contêm circuitos TNV. Algumas portas LAN e WAN usam conectores RJ-45. Tenha o devido cuidado
ao conectar os cabos.
¡Advertencia!
Para evitar la sacudida eléctrica, no conectar circuitos de seguridad de voltaje muy bajo (safety
extra-low voltage = SELV) con circuitos de voltaje de red telefónica (telephone network voltage =
TNV). Los puertos de redes de área local (local area network = LAN) contienen circuitos SELV, y los
puertos de redes de área extendida (wide area network = WAN) contienen circuitos TNV. En algunos
casos, tanto los puertos LAN como los WAN usan conectores RJ-45. Proceda con precaución al
conectar los cables.
Varning!
För att undvika elektriska stötar, koppla inte säkerhetskretsar med extra låg spänning
(SELV-kretsar) till kretsar med telefonnätspänning (TNV-kretsar). LAN-portar innehåller
SELV-kretsar och WAN-portar innehåller TNV-kretsar. Vissa LAN- och WAN-portar är försedda med
RJ-45-kontakter. Iaktta försiktighet vid anslutning av kablar.
Draft - Not Final Version
53
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Translated Safety Warnings
Statement 1023—No. 26 AWG
Warning
To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord.
Waarschuwing
Om brandgevaar te reduceren, dient slechts telecommunicatielijnsnoer nr. 26 AWG of groter
gebruikt te worden.
Varoitus
Tulipalovaaran vähentämiseksi käytä ainoastaan nro 26 AWG- tai paksumpaa tietoliikennejohdinta.
Attention
Pour réduire le risque d’incendie, n’utiliser que des cordons de lignes de télécommunications de
type AWG nº 26 ou plus larges.
Warnung
Zur Reduzierung der Feuergefahr eine Fernmeldeleitungsschnur der Größe 26 AWG oder
größer verwenden.
Avvertenza
Per ridurre il rischio di incendio, usare solo un cavo per linea di telecomunicazioni di sezione
0,12 mm
2
(26 AWG) o maggiore.
Advarsel
Bruk kun AWG nr. 26 eller telekommunikasjonsledninger med større dimensjon for å redusere faren
for brann.
Aviso
Para reduzir o risco de incêndio, utilize apenas terminais de fio de telecomunicações Nº. 26 AWG
ou superiores.
Advertencia
Para reducir el riesgo de incendios, usar sólo líneas de telecomunicaciones de calibre No. 26 AWG
o más gruesas.
Varning!
För att minska brandrisken skall endast Nr. 26 AWG eller större telekommunikationsledning
användas.
Draft - Not Final Version
54
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Translated Safety Warnings
Statement 1024—Ground Conductor
Warning
This equipment must be grounded. Never defeat the ground conductor or operate the equipment in
the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection
authority or an electrician if you are uncertain that suitable grounding is available.
Waarschuwing
Deze apparatuur dient geaard te zijn. De aardingsleiding mag nooit buiten werking worden gesteld
en de apparatuur mag nooit bediend worden zonder dat er een op de juiste wijze geïnstalleerde
aardingsleiding aanwezig is. Neem contact op met de bevoegde instantie voor elektrische
inspecties of met een elektricien als u er niet zeker van bent dat er voor passende aarding
gezorgd is.
Varoitus
Laitteiden on oltava maadoitettuja. Älä koskaan ohita maajohdinta tai käytä laitteita ilman oikein
asennettua maajohdinta. Ota yhteys sähkötarkastusviranomaiseen tai sähköasentajaan, jos olet
epävarma maadoituksen sopivuudesta.
Attention
Cet équipement doit être mis à la masse. Ne jamais rendre inopérant le conducteur de masse ni
utiliser l'équipement sans un conducteur de masse adéquatement installé. En cas de doute sur la
mise à la masse appropriée disponible, s'adresser à l'organisme responsable de la sécurité
électrique ou à un électricien.
Warnung
Dieses Gerät muss geerdet sein. Auf keinen Fall den Erdungsleiter unwirksam machen oder das
Gerät ohne einen sachgerecht installierten Erdungsleiter verwenden. Wenn Sie sich nicht sicher
sind, ob eine sachgerechte Erdung vorhanden ist, wenden Sie sich an die zuständige
Inspektionsbehörde oder einen Elektriker.
Avvertenza
Questa apparecchiatura deve essere dotata di messa a terra. Non escludere mai il conduttore di
protezione né usare l'apparecchiatura in assenza di un conduttore di protezione installato in modo
corretto. Se non si è certi della disponibilità di un adeguato collegamento di messa a terra,
richiedere un controllo elettrico presso le autorità competenti o rivolgersi a un elettricista.
Advarsel
Dette utstyret må jordes. Omgå aldri jordingslederen og bruk aldri utstyret uten riktig montert
jordingsleder. Ta kontakt med fagfolk innen elektrisk inspeksjon eller med en elektriker hvis du er
usikker på om det finnes velegnet jordning.
Aviso
Este equipamento deve ser aterrado. Nunca anule o fio terra nem opere o equipamento sem um
aterramento adequadamente instalado. Em caso de dúvida com relação ao sistema de aterramento
disponível, entre em contato com os serviços locais de inspeção elétrica ou um eletricista
qualificado.
¡Advertencia!
Este equipo debe estar conectado a tierra. No inhabilite el conductor de tierra ni haga funcionar el
equipo si no hay un conductor de tierra instalado correctamente. Póngase en contacto con la
autoridad correspondiente de inspección eléctrica o con un electricista si no está seguro de que
haya una conexión a tierra adecuada.
Varning!
Denna utrustning måste jordas. Koppla aldrig från jordledningen och använd aldrig utrustningen
utan en på lämpligt sätt installerad jordledning. Om det föreligger osäkerhet huruvida lämplig
jordning finns skall elektrisk besiktningsauktoritet eller elektriker kontaktas.
Draft - Not Final Version
55
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Translated Safety Warnings
Draft - Not Final Version
56
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Translated Safety Warnings
Statement 1025—Use Copper Conductors Only
Warning
Use copper conductors only.
Waarschuwing
Gebruik alleen koperen geleiders.
Varoitus
Käytä vain kuparijohtimia.
Attention
Utilisez uniquement des conducteurs en cuivre.
Warnung
Verwenden Sie ausschließlich Kupferleiter.
Avvertenza
Usate unicamente dei conduttori di rame.
Advarsel
Bruk bare kobberledninger.
Aviso
Utilize apenas fios condutores de cobre.
¡Advertencia!
Emplee sólo conductores de cobre.
Varning!
Använd endast ledare av koppar.
Draft - Not Final Version
57
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Translated Safety Warnings
Statement 1026—WAN Port Static Shock
Warning
Hazardous network voltages are present in WAN ports regardless of whether power to the unit is
OFF or ON. To avoid electric shock, use caution when working near WAN ports. When detaching
cables, detach the end away from the unit first.
Waarschuwing
Er is gevaarlijke netwerkspanning aanwezig in WAN poorten ongeacht of de stroom naar de router
INGESCHAKELD of UITGESCHAKELD is. Om elektrische schokken te vermijden, dient u voorzichtig te
werk te gaan wanneer u in de nabijheid van WAN poorten werkt. Wanneer u kabels losmaakt, dient
u eerst het uiteinde dat zich het verst van de eenheid vandaan bevindt, te verwijderen.
Varoitus
WAN-porteissa on vaarallisia verkkojännitteitä riippumatta siitä, onko yksikön virta kytketty vai ei.
Välttyäksesi sähköiskulta ole varovainen työskennellessäsi WAN-porttien lähettyvillä. Kun irrotat
kaapeleita, irrota yksiköstä kauimpana sijaitseva pää ensiksi.
Attention
Les ports de réseau longue distance (WAN) gèrent des tensions de réseau dangereuses, que l'unité
soit sous tension ou pas. Pour éviter tout risque d’électrocution, prenez toutes les précautions
nécessaires avant de travailler à proximité des ports WAN. Pour déconnecter les câbles,
commencez par débrancher l’extrémité la plus éloignée du routeur.
Warnung
In WAN-Ports sind gefährliche Netzspannungen vorhanden, auch wenn der Strom zur Einheit
abgeschaltet wurde. Zur Vermeidung von Elektroschock Vorsicht bei der Arbeit in der Nähe von
WAN-Ports. Beim Abtrennen von Kabeln zuerst das vom Router entfernte Ende lösen.
Avvertenza
Nelle porte WAN sono presenti tensioni di rete pericolose, sia che il sistema sia acceso o meno (ON
od OFF). Per evitare scosse elettriche, fare attenzione quando si lavora in prossimità di porte WAN.
Quando si scollegano cavi, staccare per primo il connettore collegato al router.
Advarsel!
Det er livsfarlig nettverksspenning i WAN-utganger, uavhengig av om strømmen til enheten er slått
av (OFF) eller på (ON). Vær forsiktig når du jobber nær WAN-utganger slik at du unngår elektrisk støt.
Hvis du skal løsne kabler, må du først løsne den enden som er lengst borte fra fordelingsenheten.
Aviso
Existem sempre tensões de rede perigosas nas portas WAN, independentemente da corrente para a
unidade estar desligada (OFF) ou ligada (ON). Para evitar choques eléctricos, tenha o devido
cuidado ao trabalhar junto das portas WAN. Ao desconectar os cabos, separe primeiro a
extremidade do cabo que se encontra ligada à unidade.
¡Advertencia!
En los puertos de redes de área extendida (WAN) existen tensiones de red peligrosas, tanto si la
unidad está conectada como si está desconectada. Para evitar descargas eléctricas, proceda con
precaución cuando trabaje cerca de los puertos WAN. Para desconectar los cables, desconecte
primero el extremo que va a la unidad.
Draft - Not Final Version
58
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
OL-10260-06
Translated Safety Warnings
Statement 1028—More Than One Power Supply
Varning!
Farlig nätverksspänning föreligger i WAN-portarna oavsett om strömförsörjningen till enheten är
bruten eller ej. För att undvika elektriska stötar ska du vara försiktig vid arbete i närheten av dessa
portar. När du kopplar bort en kabel ska du först koppla bort den ände som inte är ansluten
till enheten.
Warning
This unit might have more than one power supply connection. All connections must be removed to
de-energize the unit.
Waarschuwing
Deze eenheid kan meer dan één stroomtoevoeraansluiting bevatten. Alle aansluitingen dienen
ontkoppeld te worden om de eenheid te ontkrachten.
Varoitus
Tässä laitteessa voi olla useampia kuin yksi virtakytkentä. Kaikki liitännät on irrotettava, jotta
jännite poistetaan laitteesta.
Attention
Cette unité peut avoir plus d'une connexion d'alimentation. Pour supprimer toute tension et tout
courant électrique de l'unité, toutes les connexions d'alimentation doivent être débranchées.
Warnung
Dieses Gerät kann mehr als eine Stromzufuhr haben. Um sicherzustellen, dass der Einheit kein Strom
zugeführt wird, müssen alle Verbindungen entfernt werden.
Avvertenza
Questa unità può avere più di una connessione all'alimentazione elettrica. Tutte le connessioni
devono essere staccate per togliere la corrente dall'unità.
Advarsel
Denne enheten kan ha mer enn én strømtilførselskobling. Alle koblinger må fjernes fra enheten for
å utkoble all strøm.
Draft - Not Final Version